Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device tree conversions and enablement from Olof Johansson:
 "Continued device tree conversion and enablement across a number of
  platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
  smaller series as well.

  ux500 has seen continued conversion for platforms.  Several platforms
  have seen pinctrl-via-devicetree conversions for simpler
  multiplatform.  Tegra is adding data for new devices/drivers, and
  Exynos has a bunch of new bindings and devices added as well.

  So, pretty much the same progression in the right direction as the
  last few releases."

Fix up conflicts as per Olof.

* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (185 commits)
  ARM: ux500: Rename dbx500 cpufreq code to be more generic
  ARM: dts: add missing ux500 device trees
  ARM: ux500: Stop registering the PCM driver from platform code
  ARM: ux500: Move board specific GPIO info out to subordinate DTS files
  ARM: ux500: Disable the MMCI gpio-regulator by default
  ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
  ARM: Kirkwood: Add support LED of OpenBlocks A6
  ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
  ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
  ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
  ARM: kirkwood: Add support DT of second I2C bus
  ARM: kirkwood: Convert mplcec4 board to pinctrl
  ARM: Kirkwood: Convert km_kirkwood to pinctrl
  ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
  ARM: Kirkwood: Convert IX2-200 to pinctrl.
  ARM: Kirkwood: Convert lsxl boards to pinctrl.
  ARM: Kirkwood: Convert ib62x0 to pinctrl.
  ARM: Kirkwood: Convert GoFlex Net to pinctrl.
  ARM: Kirkwood: Convert dreamplug to pinctrl.
  ARM: Kirkwood: Convert dockstar to pinctrl.
  ...

Documentation/devicetree/bindings/arm/exynos/power_domain.txt

@@ -4,14 +4,13 @@ Exynos processors include support for multiple power domains which are used
 to gate power to one or more peripherals on the processor.
 
 Required Properties:
-- compatiable: should be one of the following.
+- compatible: should be one of the following.
     * samsung,exynos4210-pd - for exynos4210 type power domain.
 - reg: physical base address of the controller and length of memory mapped
     region.
 
-Optional Properties:
-- samsung,exynos4210-pd-off: Specifies that the power domain is in turned-off
-    state during boot and remains to be turned-off until explicitly turned-on.
+Node of a device using power domains must have a samsung,power-domain property
+defined with a phandle to respective power domain.
 
 Example:
 
@@ -19,3 +18,11 @@ Example:
 		compatible = "samsung,exynos4210-pd";
 		reg = <0x10023C00 0x10>;
 	};
+
+Example of the node using power domain:
+
+	node {
+		/* ... */
+		samsung,power-domain = <&lcd0>;
+		/* ... */
+	};

Documentation/devicetree/bindings/arm/fsl.txt

@@ -41,6 +41,10 @@ i.MX6 Quad SABRE Smart Device Board
 Required root node properties:
     - compatible = "fsl,imx6q-sabresd", "fsl,imx6q";
 
+i.MX6 Quad SABRE Automotive Board
+Required root node properties:
+    - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
+
 Generic i.MX boards
 -------------------
 

Documentation/devicetree/bindings/ata/exynos-sata-phy.txt

+* Samsung SATA PHY Controller
+
+SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
+Each SATA PHY controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains "samsung,exynos5-sata-phy"
+- reg               : <registers mapping>
+
+Example:
+        sata@ffe07000 {
+                compatible = "samsung,exynos5-sata-phy";
+                reg = <0xffe07000 0x1000>;
+        };

Documentation/devicetree/bindings/ata/exynos-sata.txt

+* Samsung AHCI SATA Controller
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains "samsung,exynos5-sata"
+- interrupts        : <interrupt mapping for SATA IRQ>
+- reg               : <registers mapping>
+- samsung,sata-freq : <frequency in MHz>
+
+Example:
+        sata@ffe08000 {
+                compatible = "samsung,exynos5-sata";
+                reg = <0xffe08000 0x1000>;
+                interrupts = <115>;
+        };

Documentation/devicetree/bindings/clock/imx25-clock.txt

+* Clock bindings for Freescale i.MX25
+
+Required properties:
+- compatible: Should be "fsl,imx25-ccm"
+- reg: Address and length of the register set
+- interrupts: Should contain CCM interrupt
+- #clock-cells: Should be <1>
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell.  The following is a full list of i.MX25
+clocks and IDs.
+
+	Clock			ID
+	---------------------------
+	dummy			0
+	osc			1
+	mpll			2
+	upll			3
+	mpll_cpu_3_4		4
+	cpu_sel			5
+	cpu			6
+	ahb			7
+	usb_div			8
+	ipg			9
+	per0_sel		10
+	per1_sel		11
+	per2_sel		12
+	per3_sel		13
+	per4_sel		14
+	per5_sel		15
+	per6_sel		16
+	per7_sel		17
+	per8_sel		18
+	per9_sel		19
+	per10_sel		20
+	per11_sel		21
+	per12_sel		22
+	per13_sel		23
+	per14_sel		24
+	per15_sel		25
+	per0			26
+	per1			27
+	per2			28
+	per3			29
+	per4			30
+	per5			31
+	per6			32
+	per7			33
+	per8			34
+	per9			35
+	per10			36
+	per11			37
+	per12			38
+	per13			39
+	per14			40
+	per15			41
+	csi_ipg_per		42
+	epit_ipg_per		43
+	esai_ipg_per		44
+	esdhc1_ipg_per		45
+	esdhc2_ipg_per		46
+	gpt_ipg_per		47
+	i2c_ipg_per		48
+	lcdc_ipg_per		49
+	nfc_ipg_per		50
+	owire_ipg_per		51
+	pwm_ipg_per		52
+	sim1_ipg_per		53
+	sim2_ipg_per		54
+	ssi1_ipg_per		55
+	ssi2_ipg_per		56
+	uart_ipg_per		57
+	ata_ahb			58
+	reserved		59
+	csi_ahb			60
+	emi_ahb			61
+	esai_ahb		62
+	esdhc1_ahb		63
+	esdhc2_ahb		64
+	fec_ahb			65
+	lcdc_ahb		66
+	rtic_ahb		67
+	sdma_ahb		68
+	slcdc_ahb		69
+	usbotg_ahb		70
+	reserved		71
+	reserved		72
+	reserved		73
+	reserved		74
+	can1_ipg		75
+	can2_ipg		76
+	csi_ipg			77
+	cspi1_ipg		78
+	cspi2_ipg		79
+	cspi3_ipg		80
+	dryice_ipg		81
+	ect_ipg			82
+	epit1_ipg		83
+	epit2_ipg		84
+	reserved		85
+	esdhc1_ipg		86
+	esdhc2_ipg		87
+	fec_ipg			88
+	reserved		89
+	reserved		90
+	reserved		91
+	gpt1_ipg		92
+	gpt2_ipg		93
+	gpt3_ipg		94
+	gpt4_ipg		95
+	reserved		96
+	reserved		97
+	reserved		98
+	iim_ipg			99
+	reserved		100
+	reserved		101
+	kpp_ipg			102
+	lcdc_ipg		103
+	reserved		104
+	pwm1_ipg		105
+	pwm2_ipg		106
+	pwm3_ipg		107
+	pwm4_ipg		108
+	rngb_ipg		109
+	reserved		110
+	scc_ipg			111
+	sdma_ipg		112
+	sim1_ipg		113
+	sim2_ipg		114
+	slcdc_ipg		115
+	spba_ipg		116
+	ssi1_ipg		117
+	ssi2_ipg		118
+	tsc_ipg			119
+	uart1_ipg		120
+	uart2_ipg		121
+	uart3_ipg		122
+	uart4_ipg		123
+	uart5_ipg		124
+	reserved		125
+	wdt_ipg			126
+
+Examples:
+
+clks: ccm@53f80000 {
+	compatible = "fsl,imx25-ccm";
+	reg = <0x53f80000 0x4000>;
+	interrupts = <31>;
+	clock-output-names = ...
+			"uart_ipg",
+			"uart_serial",
+			...;
+};
+
+uart1: serial@43f90000 {
+	compatible = "fsl,imx25-uart", "fsl,imx21-uart";
+	reg = <0x43f90000 0x4000>;
+	interrupts = <45>;
+	clocks = <&clks 79>, <&clks 50>;
+	clock-names = "ipg", "per";
+	status = "disabled";
+};

Documentation/devicetree/bindings/clock/zynq-7000.txt

+Device Tree Clock bindings for the Zynq 7000 EPP
+
+The Zynq EPP has several different clk providers, each with there own bindings.
+The purpose of this document is to document their usage.
+
+See clock_bindings.txt for more information on the generic clock bindings.
+See Chapter 25 of Zynq TRM for more information about Zynq clocks.
+
+== PLLs ==
+
+Used to describe the ARM_PLL, DDR_PLL, and IO_PLL.
+
+Required properties:
+- #clock-cells : shall be 0 (only one clock is output from this node)
+- compatible : "xlnx,zynq-pll"
+- reg : pair of u32 values, which are the address offsets within the SLCR
+        of the relevant PLL_CTRL register and PLL_CFG register respectively
+- clocks : phandle for parent clock.  should be the phandle for ps_clk
+
+Optional properties:
+- clock-output-names : name of the output clock
+
+Example:
+	armpll: armpll {
+		#clock-cells = <0>;
+		compatible = "xlnx,zynq-pll";
+		clocks = <&ps_clk>;
+		reg = <0x100 0x110>;
+		clock-output-names = "armpll";
+	};
+
+== Peripheral clocks ==
+
+Describes clock node for the SDIO, SMC, SPI, QSPI, and UART clocks.
+
+Required properties:
+- #clock-cells : shall be 1
+- compatible : "xlnx,zynq-periph-clock"
+- reg : a single u32 value, describing the offset within the SLCR where
+        the CLK_CTRL register is found for this peripheral
+- clocks : phandle for parent clocks.  should hold phandles for
+           the IO_PLL, ARM_PLL, and DDR_PLL in order
+- clock-output-names : names of the output clock(s).  For peripherals that have
+                       two output clocks (for example, the UART), two clocks
+                       should be listed.
+
+Example:
+	uart_clk: uart_clk {
+		#clock-cells = <1>;
+		compatible = "xlnx,zynq-periph-clock";
+		clocks = <&iopll &armpll &ddrpll>;
+		reg = <0x154>;
+		clock-output-names = "uart0_ref_clk",
+				     "uart1_ref_clk";
+	};

Documentation/devicetree/bindings/drm/exynos/hdmi.txt

+Device-Tree bindings for drm hdmi driver
+
+Required properties:
+- compatible: value should be "samsung,exynos5-hdmi".
+- reg: physical base address of the hdmi and length of memory mapped
+	region.
+- interrupts: interrupt number to the cpu.
+- hpd-gpio: following information about the hotplug gpio pin.
+	a) phandle of the gpio controller node.
+	b) pin number within the gpio controller.
+	c) pin function mode.
+	d) optional flags and pull up/down.
+	e) drive strength.
+
+Example:
+
+	hdmi {
+		compatible = "samsung,exynos5-hdmi";
+		reg = <0x14530000 0x100000>;
+		interrupts = <0 95 0>;
+		hpd-gpio = <&gpx3 7 0xf 1 3>;
+	};

Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt

+Device-Tree bindings for hdmiddc driver
+
+Required properties:
+- compatible: value should be "samsung,exynos5-hdmiddc".
+- reg: I2C address of the hdmiddc device.
+
+Example:
+
+	hdmiddc {
+		compatible = "samsung,exynos5-hdmiddc";
+		reg = <0x50>;
+	};

Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt

+Device-Tree bindings for hdmiphy driver
+
+Required properties:
+- compatible: value should be "samsung,exynos5-hdmiphy".
+- reg: I2C address of the hdmiphy device.
+
+Example:
+
+	hdmiphy {
+		compatible = "samsung,exynos5-hdmiphy";
+		reg = <0x38>;
+	};

Documentation/devicetree/bindings/drm/exynos/mixer.txt

+Device-Tree bindings for mixer driver
+
+Required properties:
+- compatible: value should be "samsung,exynos5-mixer".
+- reg: physical base address of the mixer and length of memory mapped
+	region.
+- interrupts: interrupt number to the cpu.
+
+Example:
+
+	mixer {
+		compatible = "samsung,exynos5-mixer";
+		reg = <0x14450000 0x10000>;
+		interrupts = <0 94 0>;
+	};

Documentation/devicetree/bindings/gpio/gpio-poweroff.txt

+GPIO line that should be set high/low to power off a device
+
+Required properties:
+- compatible : should be "gpio-poweroff".
+- gpios : The GPIO to set high/low, see "gpios property" in
+  Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be
+  low to power down the board set it to "Active Low", otherwise set
+  gpio to "Active High".
+
+Optional properties:
+- input : Initially configure the GPIO line as an input. Only reconfigure
+  it to an output when the pm_power_off function is called. If this optional
+  property is not specified, the GPIO is initialized as an output in its
+  inactive state.
+
+
+Examples:
+
+gpio-poweroff {
+	compatible = "gpio-poweroff";
+	gpios = <&gpio 4 0>; /* GPIO 4 Active Low */
+};

Documentation/devicetree/bindings/input/touchscreen/bu21013.txt

+* Rohm BU21013 Touch Screen
+
+Required properties:
+ - compatible              : "rohm,bu21013_tp"
+ - reg                     :  I2C device address
+
+Optional properties:
+ - touch-gpio              : GPIO pin registering a touch event
+ - <supply_name>-supply    : Phandle to a regulator supply
+ - rohm,touch-max-x        : Maximum outward permitted limit in the X axis
+ - rohm,touch-max-y        : Maximum outward permitted limit in the Y axis
+ - rohm,flip-x             : Flip touch coordinates on the X axis
+ - rohm,flip-y             : Flip touch coordinates on the Y axis
+
+Example:
+
+	i2c@80110000 {
+		bu21013_tp@0x5c {
+			compatible = "rohm,bu21013_tp";
+			reg = <0x5c>;
+			touch-gpio = <&gpio2 20 0x4>;
+			avdd-supply = <&ab8500_ldo_aux1_reg>;
+
+			rohm,touch-max-x = <384>;
+			rohm,touch-max-y = <704>;
+			rohm,flip-y;
+		};
+	};

Documentation/devicetree/bindings/media/s5p-mfc.txt

+* Samsung Multi Format Codec (MFC)
+
+Multi Format Codec (MFC) is the IP present in Samsung SoCs which
+supports high resolution decoding and encoding functionalities.
+The MFC device driver is a v4l2 driver which can encode/decode
+video raw/elementary streams and has support for all popular
+video codecs.
+
+Required properties:
+  - compatible : value should be either one among the following
+	(a) "samsung,mfc-v5" for MFC v5 present in Exynos4 SoCs
+	(b) "samsung,mfc-v6" for MFC v6 present in Exynos5 SoCs
+
+  - reg : Physical base address of the IP registers and length of memory
+	  mapped region.
+
+  - interrupts : MFC interrupt number to the CPU.
+
+  - samsung,mfc-r : Base address of the first memory bank used by MFC
+		    for DMA contiguous memory allocation and its size.
+
+  - samsung,mfc-l : Base address of the second memory bank used by MFC
+		    for DMA contiguous memory allocation and its size.

Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt

@@ -7,8 +7,10 @@ Required properties:
 - compatible: "marvell,88f6180-pinctrl",
               "marvell,88f6190-pinctrl", "marvell,88f6192-pinctrl",
               "marvell,88f6281-pinctrl", "marvell,88f6282-pinctrl"
+              "marvell,98dx4122-pinctrl"
 
 This driver supports all kirkwood variants, i.e. 88f6180, 88f619x, and 88f628x.
+It also support the 88f6281-based variant in the 98dx412x Bobcat SoCs.
 
 Available mpp pins/groups and functions:
 Note: brackets (x) are not part of the mpp name for marvell,function and given
@@ -277,3 +279,40 @@ mpp46         46       gpio, ts(mp10), tdm(fs), lcd(hsync)
 mpp47         47       gpio, ts(mp11), tdm(drx), lcd(vsync)
 mpp48         48       gpio, ts(mp12), tdm(dtx), lcd(d16)
 mpp49         49       gpo, tdm(rx0ql), pex(clkreq), lcd(d17)
+
+* Marvell Bobcat 98dx4122
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, nand(io2), spi(cs)
+mpp1          1        gpo, nand(io3), spi(mosi)
+mpp2          2        gpo, nand(io4), spi(sck)
+mpp3          3        gpo, nand(io5), spi(miso)
+mpp4          4        gpio, nand(io6), uart0(rxd)
+mpp5          5        gpo, nand(io7), uart0(txd)
+mpp6          6        sysrst(out), spi(mosi)
+mpp7          7        gpo, pex(rsto), spi(cs)
+mpp8          8        gpio, twsi0(sda), uart0(rts), uart1(rts)
+mpp9          9        gpio, twsi(sck), uart0(cts), uart1(cts)
+mpp10         10       gpo, spi(sck), uart0(txd)
+mpp11         11       gpio, spi(miso), uart0(rxd)
+mpp13         13       gpio, uart1(txd)
+mpp14         14       gpio, uart1(rxd)
+mpp15         15       gpio, uart0(rts)
+mpp16         16       gpio, uart0(cts)
+mpp18         18       gpo, nand(io0)
+mpp19         19       gpo, nand(io1)
+mpp34         34       gpio
+mpp35         35       gpio
+mpp36         36       gpio
+mpp37         37       gpio
+mpp38         38       gpio
+mpp39         39       gpio
+mpp40         40       gpio
+mpp41         41       gpio
+mpp42         42       gpio
+mpp43         43       gpio
+mpp44         44       gpio
+mpp45         45       gpio
+mpp49         49       gpio
+

Documentation/devicetree/bindings/usb/ehci-orion.txt

+* EHCI controller, Orion Marvell variants
+
+Required properties:
+- compatible: must be "marvell,orion-ehci"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: The EHCI interrupt
+
+Example:
+
+	ehci@50000 {
+		compatible = "marvell,orion-ehci";
+		reg = <0x50000 0x1000>;
+		interrupts = <19>;
+	};

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -55,4 +55,5 @@ ti	Texas Instruments
 via	VIA Technologies, Inc.
 wlf	Wolfson Microelectronics
 wm	Wondermedia Technologies, Inc.
+winbond Winbond Electronics corp.
 xlnx	Xilinx

Documentation/devicetree/bindings/watchdog/atmel-wdt.txt

+* Atmel Watchdog Timers
+
+** at91sam9-wdt
+
+Required properties:
+- compatible: must be "atmel,at91sam9260-wdt".
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+Example:
+
+	watchdog@fffffd40 {
+		compatible = "atmel,at91sam9260-wdt";
+		reg = <0xfffffd40 0x10>;
+	};

arch/arm/Kconfig

@@ -536,6 +536,8 @@ config ARCH_DOVE
 	select CPU_V7
 	select GENERIC_CLOCKEVENTS
 	select MIGHT_HAVE_PCI
+	select PINCTRL
+	select PINCTRL_DOVE
 	select PLAT_ORION_LEGACY
 	select USB_ARCH_HAS_EHCI
 	help
@@ -548,6 +550,8 @@ config ARCH_KIRKWOOD
 	select GENERIC_CLOCKEVENTS
 	select PCI
 	select PCI_QUIRKS
+	select PINCTRL
+	select PINCTRL_KIRKWOOD
 	select PLAT_ORION_LEGACY
 	help
 	  Support for the following Marvell Kirkwood series SoCs:
@@ -962,6 +966,7 @@ config ARCH_ZYNQ
 	bool "Xilinx Zynq ARM Cortex A9 Platform"
 	select ARM_AMBA
 	select ARM_GIC
+	select COMMON_CLK
 	select CPU_V7
 	select GENERIC_CLOCKEVENTS
 	select ICST

arch/arm/Kconfig.debug

@@ -132,6 +132,23 @@ choice
 		  their output to UART1 serial port on DaVinci TNETV107X
 		  devices.
 
+	config DEBUG_ZYNQ_UART0
+		bool "Kernel low-level debugging on Xilinx Zynq using UART0"
+		depends on ARCH_ZYNQ
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART0 on the Zynq platform.
+
+	config DEBUG_ZYNQ_UART1
+		bool "Kernel low-level debugging on Xilinx Zynq using UART1"
+		depends on ARCH_ZYNQ
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART1 on the Zynq platform.
+
+		  If you have a ZC702 board and want early boot messages to
+		  appear on the USB serial adaptor, select this option.
+
 	config DEBUG_DC21285_PORT
 		bool "Kernel low-level debugging messages via footbridge serial port"
 		depends on FOOTBRIDGE
@@ -209,20 +226,12 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on i.MX50 or i.MX53.
 
-	config DEBUG_IMX6Q_UART2
-		bool "i.MX6Q Debug UART2"
+	config DEBUG_IMX6Q_UART
+		bool "i.MX6Q Debug UART"
 		depends on SOC_IMX6Q
 		help
 		  Say Y here if you want kernel low-level debugging support
-		  on i.MX6Q UART2. This is correct for e.g. the SabreLite
-                  board.
-
-	config DEBUG_IMX6Q_UART4
-		bool "i.MX6Q Debug UART4"
-		depends on SOC_IMX6Q
-		help
-		  Say Y here if you want kernel low-level debugging support
-		  on i.MX6Q UART4.
+		  on i.MX6Q.
 
 	config DEBUG_MMP_UART2
 		bool "Kernel low-level debugging message via MMP UART2"
@@ -434,6 +443,15 @@ choice
 
 endchoice
 
+config DEBUG_IMX6Q_UART_PORT
+	int "i.MX6Q Debug UART Port (1-5)" if DEBUG_IMX6Q_UART
+	range 1 5
+	default 1
+	depends on SOC_IMX6Q
+	help
+	  Choose UART port on which kernel low-level debug messages
+	  should be output.
+
 config DEBUG_LL_INCLUDE
 	string
 	default "debug/icedcc.S" if DEBUG_ICEDCC
@@ -443,8 +461,7 @@ config DEBUG_LL_INCLUDE
 				 DEBUG_IMX31_IMX35_UART || \
 				 DEBUG_IMX51_UART || \
 				 DEBUG_IMX50_IMX53_UART ||\
-				 DEBUG_IMX6Q_UART2 || \
-				 DEBUG_IMX6Q_UART4
+				 DEBUG_IMX6Q_UART
 	default "debug/highbank.S" if DEBUG_HIGHBANK_UART
 	default "debug/mvebu.S" if DEBUG_MVEBU_UART
 	default "debug/picoxcell.S" if DEBUG_PICOXCELL_UART

arch/arm/boot/dts/Makefile

@@ -34,6 +34,8 @@ dtb-$(CONFIG_ARCH_AT91) += at91sam9x35ek.dtb
 
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
 dtb-$(CONFIG_ARCH_BCM) += bcm11351-brt.dtb
+dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
+	da850-evm.dtb
 dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \
 	dove-cubox.dtb \
 	dove-dove-db.dtb
@@ -41,7 +43,10 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos4210-smdkv310.dtb \
 	exynos4210-trats.dtb \
 	exynos5250-smdk5250.dtb \
-	exynos5440-ssdk5440.dtb
+	exynos5440-ssdk5440.dtb \
+	exynos4412-smdk4412.dtb \
+	exynos5250-smdk5250.dtb \
+	exynos5250-snow.dtb
 dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb \
 	ecx-2000.dtb
 dtb-$(CONFIG_ARCH_INTEGRATOR) += integratorap.dtb \
@@ -79,16 +84,20 @@ dtb-$(CONFIG_ARCH_MXC) += imx51-babbage.dtb \
 	imx53-qsb.dtb \
 	imx53-smd.dtb \
 	imx6q-arm2.dtb \
+	imx6q-sabreauto.dtb \
 	imx6q-sabrelite.dtb \
 	imx6q-sabresd.dtb
 dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx23-olinuxino.dtb \
 	imx23-stmp378x_devb.dtb \
+	imx28-apf28.dtb \
+	imx28-apf28dev.dtb \
 	imx28-apx4devkit.dtb \
 	imx28-cfa10036.dtb \
 	imx28-cfa10049.dtb \
 	imx28-evk.dtb \
 	imx28-m28evk.dtb \
+	imx28-sps1.dtb \
 	imx28-tx28.dtb
 dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3-beagle.dtb \
@@ -105,7 +114,10 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	am335x-bone.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
-dtb-$(CONFIG_ARCH_U8500) += snowball.dtb
+dtb-$(CONFIG_ARCH_U8500) += snowball.dtb \
+	hrefprev60.dtb \
+	hrefv60plus.dtb \
+	ccu9540.dtb
 dtb-$(CONFIG_ARCH_SHMOBILE) += emev2-kzm9d.dtb \
 	r8a7740-armadillo800eva.dtb \
 	sh73a0-kzm9g.dtb \
@@ -137,6 +149,7 @@ dtb-$(CONFIG_ARCH_VEXPRESS) += vexpress-v2p-ca5s.dtb \
 dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
 	wm8505-ref.dtb \
 	wm8650-mid.dtb
+dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb
 
 targets += dtbs
 endif

arch/arm/boot/dts/at91sam9260.dtsi

@@ -479,6 +479,12 @@ trigger@3 {
 					trigger-external;
 				};
 			};
+
+			watchdog@fffffd40 {
+				compatible = "atmel,at91sam9260-wdt";
+				reg = <0xfffffd40 0x10>;
+				status = "disabled";
+			};
 		};
 
 		nand0: nand@40000000 {

arch/arm/boot/dts/at91sam9263.dtsi

@@ -404,6 +404,12 @@ mmc1: mmc@fff84000 {
 				#size-cells = <0>;
 				status = "disabled";
 			};
+
+			watchdog@fffffd40 {
+				compatible = "atmel,at91sam9260-wdt";
+				reg = <0xfffffd40 0x10>;
+				status = "disabled";
+			};
 		};
 
 		nand0: nand@40000000 {

arch/arm/boot/dts/at91sam9g45.dtsi

@@ -473,6 +473,12 @@ mmc1: mmc@fffd0000 {
 				#size-cells = <0>;
 				status = "disabled";
 			};
+
+			watchdog@fffffd40 {
+				compatible = "atmel,at91sam9260-wdt";
+				reg = <0xfffffd40 0x10>;
+				status = "disabled";
+			};
 		};
 
 		nand0: nand@40000000 {

arch/arm/boot/dts/ccu9540.dts

+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "dbx5x0.dtsi"
+
+/ {
+	model = "ST-Ericsson CCU9540 platform with Device Tree";
+	compatible = "st-ericsson,ccu9540", "st-ericsson,u9540";
+
+	memory {
+		reg = <0x00000000 0x20000000>;
+	};
+
+	soc-u9500 {
+		uart@80120000 {
+			status = "okay";
+		};
+
+		uart@80121000 {
+			status = "okay";
+		};
+
+		uart@80007000 {
+			status = "okay";
+		};
+
+		// External Micro SD slot
+		sdi0_per1@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			mmc-cap-sd-highspeed;
+			mmc-cap-mmc-highspeed;
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+
+			cd-gpios  = <&gpio7 6 0x4>; // 230
+			cd-inverted;
+
+			status = "okay";
+		};
+
+
+		// WLAN SDIO channel
+		sdi1_per2@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+
+			status = "okay";
+		};
+
+		// On-board eMMC
+		sdi4_per2@80114000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <100000000>;
+			bus-width = <8>;
+			mmc-cap-mmc-highspeed;
+			vmmc-supply = <&ab8500_ldo_aux2_reg>;
+
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/cros5250-common.dtsi

+/*
+ * Common device tree include for all Exynos 5250 boards based off of Daisy.
+ *
+ * Copyright (c) 2012 Google, Inc
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/ {
+	aliases {
+	};
+
+	memory {
+		reg = <0x40000000 0x80000000>;
+	};
+
+	chosen {
+	};
+
+	i2c@12C60000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <378000>;
+		gpios = <&gpb3 0 2 3 0>,
+			<&gpb3 1 2 3 0>;
+	};
+
+	i2c@12C70000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <378000>;
+		gpios = <&gpb3 2 2 3 0>,
+			<&gpb3 3 2 3 0>;
+	};
+
+	i2c@12C80000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <66000>;
+
+		/*
+		 * Disabled pullups since external part has its own pullups and
+		 * double-pulling gets us out of spec in some cases.
+		 */
+		gpios = <&gpa0 6 3 0 0>,
+			<&gpa0 7 3 0 0>;
+
+		hdmiddc@50 {
+			compatible = "samsung,exynos5-hdmiddc";
+			reg = <0x50>;
+		};
+	};
+
+	i2c@12C90000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <66000>;
+		gpios = <&gpa1 2 3 3 0>,
+			<&gpa1 3 3 3 0>;
+	};
+
+	i2c@12CA0000 {
+		status = "disabled";
+	};
+
+	i2c@12CB0000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <66000>;
+		gpios = <&gpa2 2 3 3 0>,
+			<&gpa2 3 3 3 0>;
+	};
+
+	i2c@12CC0000 {
+		status = "disabled";
+	};
+
+	i2c@12CD0000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <66000>;
+		gpios = <&gpb2 2 3 3 0>,
+			<&gpb2 3 3 3 0>;
+	};
+
+	i2c@12CE0000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <378000>;
+
+		hdmiphy@38 {
+			compatible = "samsung,exynos5-hdmiphy";
+			reg = <0x38>;
+		};
+	};
+
+	dwmmc0@12200000 {
+		num-slots = <1>;
+		supports-highspeed;
+		broken-cd;
+		fifo-depth = <0x80>;
+		card-detect-delay = <200>;
+		samsung,dw-mshc-ciu-div = <3>;
+		samsung,dw-mshc-sdr-timing = <2 3 3>;
+		samsung,dw-mshc-ddr-timing = <1 2 3>;
+
+		slot@0 {
+			reg = <0>;
+			bus-width = <8>;
+			gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
+				<&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
+				<&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>,
+				<&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
+				<&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>;
+		};
+	};
+
+	dwmmc1@12210000 {
+		status = "disabled";
+	};
+
+	dwmmc2@12220000 {
+		num-slots = <1>;
+		supports-highspeed;
+		fifo-depth = <0x80>;
+		card-detect-delay = <200>;
+		samsung,dw-mshc-ciu-div = <3>;
+		samsung,dw-mshc-sdr-timing = <2 3 3>;
+		samsung,dw-mshc-ddr-timing = <1 2 3>;
+
+		slot@0 {
+			reg = <0>;
+			bus-width = <4>;
+			samsung,cd-pinmux-gpio = <&gpc3 2 2 3 3>;
+			wp-gpios = <&gpc2 1 0 0 3>;
+			gpios = <&gpc3 0 2 0 3>, <&gpc3 1 2 0 3>,
+				<&gpc3 3 2 3 3>, <&gpc3 4 2 3 3>,
+				<&gpc3 5 2 3 3>, <&gpc3 6 2 3 3>;
+		};
+	};
+
+	dwmmc3@12230000 {
+		num-slots = <1>;
+		supports-highspeed;
+		broken-cd;
+		fifo-depth = <0x80>;
+		card-detect-delay = <200>;
+		samsung,dw-mshc-ciu-div = <3>;
+		samsung,dw-mshc-sdr-timing = <2 3 3>;
+		samsung,dw-mshc-ddr-timing = <1 2 3>;
+
+		slot@0 {
+			reg = <0>;
+			bus-width = <4>;
+			/* See board-specific dts files for GPIOs */
+		};
+	};
+
+	spi_0: spi@12d20000 {
+		status = "disabled";
+	};
+
+	spi_1: spi@12d30000 {
+		gpios = <&gpa2 4 2 3 0>,
+			<&gpa2 6 2 3 0>,
+			<&gpa2 7 2 3 0>;
+		samsung,spi-src-clk = <0>;
+		num-cs = <1>;
+	};
+
+	spi_2: spi@12d40000 {
+		status = "disabled";
+	};
+
+	hdmi {
+		hpd-gpio = <&gpx3 7 0xf 1 3>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		power {
+			label = "Power";
+			gpios = <&gpx1 3 0 0x10000 0>;
+			linux,code = <116>; /* KEY_POWER */
+			gpio-key,wakeup;
+		};
+	};
+};

arch/arm/boot/dts/dbx5x0.dtsi

@@ -217,123 +217,103 @@ db8500-prcmu-regulators {
 				// DB8500_REGULATOR_VAPE
 				db8500_vape_reg: db8500_vape {
 					regulator-compatible = "db8500_vape";
-					regulator-name = "db8500-vape";
 					regulator-always-on;
 				};
 
 				// DB8500_REGULATOR_VARM
 				db8500_varm_reg: db8500_varm {
 					regulator-compatible = "db8500_varm";
-					regulator-name = "db8500-varm";
 				};
 
 				// DB8500_REGULATOR_VMODEM
 				db8500_vmodem_reg: db8500_vmodem {
 					regulator-compatible = "db8500_vmodem";
-					regulator-name = "db8500-vmodem";
 				};
 
 				// DB8500_REGULATOR_VPLL
 				db8500_vpll_reg: db8500_vpll {
 					regulator-compatible = "db8500_vpll";
-					regulator-name = "db8500-vpll";
 				};
 
 				// DB8500_REGULATOR_VSMPS1
 				db8500_vsmps1_reg: db8500_vsmps1 {
 					regulator-compatible = "db8500_vsmps1";
-					regulator-name = "db8500-vsmps1";
 				};
 
 				// DB8500_REGULATOR_VSMPS2
 				db8500_vsmps2_reg: db8500_vsmps2 {
 					regulator-compatible = "db8500_vsmps2";
-					regulator-name = "db8500-vsmps2";
 				};
 
 				// DB8500_REGULATOR_VSMPS3
 				db8500_vsmps3_reg: db8500_vsmps3 {
 					regulator-compatible = "db8500_vsmps3";
-					regulator-name = "db8500-vsmps3";
 				};
 
 				// DB8500_REGULATOR_VRF1
 				db8500_vrf1_reg: db8500_vrf1 {
 					regulator-compatible = "db8500_vrf1";
-					regulator-name = "db8500-vrf1";
 				};
 
 				// DB8500_REGULATOR_SWITCH_SVAMMDSP
 				db8500_sva_mmdsp_reg: db8500_sva_mmdsp {
 					regulator-compatible = "db8500_sva_mmdsp";
-					regulator-name = "db8500-sva-mmdsp";
 				};
 
 				// DB8500_REGULATOR_SWITCH_SVAMMDSPRET
 				db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret {
 					regulator-compatible = "db8500_sva_mmdsp_ret";
-					regulator-name = "db8500-sva-mmdsp-ret";
 				};
 
 				// DB8500_REGULATOR_SWITCH_SVAPIPE
 				db8500_sva_pipe_reg: db8500_sva_pipe {
 					regulator-compatible = "db8500_sva_pipe";
-					regulator-name = "db8500_sva_pipe";
 				};
 
 				// DB8500_REGULATOR_SWITCH_SIAMMDSP
 				db8500_sia_mmdsp_reg: db8500_sia_mmdsp {
 					regulator-compatible = "db8500_sia_mmdsp";
-					regulator-name = "db8500_sia_mmdsp";
 				};
 
 				// DB8500_REGULATOR_SWITCH_SIAMMDSPRET
 				db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret {
-					regulator-name = "db8500-sia-mmdsp-ret";
 				};
 
 				// DB8500_REGULATOR_SWITCH_SIAPIPE
 				db8500_sia_pipe_reg: db8500_sia_pipe {
 					regulator-compatible = "db8500_sia_pipe";
-					regulator-name = "db8500-sia-pipe";
 				};
 
 				// DB8500_REGULATOR_SWITCH_SGA
 				db8500_sga_reg: db8500_sga {
 					regulator-compatible = "db8500_sga";
-					regulator-name = "db8500-sga";
 					vin-supply = <&db8500_vape_reg>;
 				};
 
 				// DB8500_REGULATOR_SWITCH_B2R2_MCDE
 				db8500_b2r2_mcde_reg: db8500_b2r2_mcde {
 					regulator-compatible = "db8500_b2r2_mcde";
-					regulator-name = "db8500-b2r2-mcde";
 					vin-supply = <&db8500_vape_reg>;
 				};
 
 				// DB8500_REGULATOR_SWITCH_ESRAM12
 				db8500_esram12_reg: db8500_esram12 {
 					regulator-compatible = "db8500_esram12";
-					regulator-name = "db8500-esram12";
 				};
 
 				// DB8500_REGULATOR_SWITCH_ESRAM12RET
 				db8500_esram12_ret_reg: db8500_esram12_ret {
 					regulator-compatible = "db8500_esram12_ret";
-					regulator-name = "db8500-esram12-ret";
 				};
 
 				// DB8500_REGULATOR_SWITCH_ESRAM34
 				db8500_esram34_reg: db8500_esram34 {
 					regulator-compatible = "db8500_esram34";
-					regulator-name = "db8500-esram34";
 				};
 
 				// DB8500_REGULATOR_SWITCH_ESRAM34RET
 				db8500_esram34_ret_reg: db8500_esram34_ret {
 					regulator-compatible = "db8500_esram34_ret";
-					regulator-name = "db8500-esram34-ret";
 				};
 			};
 
@@ -412,7 +392,6 @@ ab8500-regulators {
 					// supplies to the display/camera
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 						regulator-compatible = "ab8500_ldo_aux1";
-						regulator-name = "V-DISPLAY";
 						regulator-min-microvolt = <2500000>;
 						regulator-max-microvolt = <2900000>;
 						regulator-boot-on;
@@ -423,7 +402,6 @@ ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 					// supplies to the on-board eMMC
 					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
 						regulator-compatible = "ab8500_ldo_aux2";
-						regulator-name = "V-eMMC1";
 						regulator-min-microvolt = <1100000>;
 						regulator-max-microvolt = <3300000>;
 					};
@@ -431,7 +409,6 @@ ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
 					// supply for VAUX3; SDcard slots
 					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
 						regulator-compatible = "ab8500_ldo_aux3";
-						regulator-name = "V-MMC-SD";
 						regulator-min-microvolt = <1100000>;
 						regulator-max-microvolt = <3300000>;
 					};
@@ -439,49 +416,41 @@ ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
 					// supply for v-intcore12; VINTCORE12 LDO
 					ab8500_ldo_initcore_reg: ab8500_ldo_initcore {
 						regulator-compatible = "ab8500_ldo_initcore";
-						regulator-name = "V-INTCORE";
 					};
 
 					// supply for tvout; gpadc; TVOUT LDO
 					ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
 						regulator-compatible = "ab8500_ldo_tvout";
-						regulator-name = "V-TVOUT";
 					};
 
 					// supply for ab8500-usb; USB LDO
 					ab8500_ldo_usb_reg: ab8500_ldo_usb {
 						regulator-compatible = "ab8500_ldo_usb";
-						regulator-name = "dummy";
 					};
 
 					// supply for ab8500-vaudio; VAUDIO LDO
 					ab8500_ldo_audio_reg: ab8500_ldo_audio {
 						regulator-compatible = "ab8500_ldo_audio";
-						regulator-name = "V-AUD";
 					};
 
 					// supply for v-anamic1 VAMic1-LDO
 					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
 						regulator-compatible = "ab8500_ldo_anamic1";
-						regulator-name = "V-AMIC1";
 					};
 
 					// supply for v-amic2; VAMIC2 LDO; reuse constants for AMIC1
 					ab8500_ldo_amamic2_reg: ab8500_ldo_amamic2 {
 						regulator-compatible = "ab8500_ldo_amamic2";
-						regulator-name = "V-AMIC2";
 					};
 
 					// supply for v-dmic; VDMIC LDO
 					ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
 						regulator-compatible = "ab8500_ldo_dmic";
-						regulator-name = "V-DMIC";
 					};
 
 					// supply for U8500 CSI/DSI; VANA LDO
 					ab8500_ldo_ana_reg: ab8500_ldo_ana {
 						regulator-compatible = "ab8500_ldo_ana";
-						regulator-name = "V-CSI/DSI";
 					};
 				};
 			};
@@ -585,42 +554,42 @@ uart@80007000 {
 			status = "disabled";
 		};
 
-		sdi@80126000 {
+		sdi0_per1@80126000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80126000 0x1000>;
 			interrupts = <0 60 0x4>;
 			status = "disabled";
 		};
 
-		sdi@80118000 {
+		sdi1_per2@80118000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80118000 0x1000>;
 			interrupts = <0 50 0x4>;
 			status = "disabled";
 		};
 
-		sdi@80005000 {
+		sdi2_per3@80005000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80005000 0x1000>;
 			interrupts = <0 41 0x4>;
 			status = "disabled";
 		};
 
-		sdi@80119000 {
+		sdi3_per2@80119000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80119000 0x1000>;
 			interrupts = <0 59 0x4>;
 			status = "disabled";
 		};
 
-		sdi@80114000 {
+		sdi4_per2@80114000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80114000 0x1000>;
 			interrupts = <0 99 0x4>;
 			status = "disabled";
 		};
 
-		sdi@80008000 {
+		sdi5_per3@80008000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80008000 0x1000>;
 			interrupts = <0 100 0x4>;
@@ -674,5 +643,18 @@ cpufreq-cooling {
 			status = "disabled";
 		 };
 
+		vmmci: regulator-gpio {
+			compatible = "regulator-gpio";
+
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2600000>;
+			regulator-name = "mmci-reg";
+			regulator-type = "voltage";
+
+			states = <1800000 0x1
+				  2900000 0x0>;
+
+			status = "disabled";
+		};
 	};
 };

arch/arm/boot/dts/dove-cubox.dts

@@ -40,3 +40,13 @@ spi-flash@0 {
 		reg = <0>;
 	};
 };
+
+&pinctrl {
+	pinctrl-0 = <&pmx_gpio_18>;
+	pinctrl-names = "default";
+
+	pmx_gpio_18: pmx-gpio-18 {
+		marvell,pins = "mpp18";
+		marvell,function = "gpio";
+	};
+};

arch/arm/boot/dts/dove.dtsi

@@ -4,6 +4,12 @@ / {
 	compatible = "marvell,dove";
 	model = "Marvell Armada 88AP510 SoC";
 
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+	};
+
 	soc@f1000000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -72,7 +78,8 @@ gpio0: gpio@d0400 {
 			#gpio-cells = <2>;
 			gpio-controller;
 			reg = <0xd0400 0x20>;
-			ngpio = <32>;
+			ngpios = <32>;
+			interrupt-controller;
 			interrupts = <12>, <13>, <14>, <60>;
 		};
 
@@ -81,7 +88,8 @@ gpio1: gpio@d0420 {
 			#gpio-cells = <2>;
 			gpio-controller;
 			reg = <0xd0420 0x20>;
-			ngpio = <32>;
+			ngpios = <32>;
+			interrupt-controller;
 			interrupts = <61>;
 		};
 
@@ -90,7 +98,12 @@ gpio2: gpio@e8400 {
 			#gpio-cells = <2>;
 			gpio-controller;
 			reg = <0xe8400 0x0c>;
-			ngpio = <8>;
+			ngpios = <8>;
+		};
+
+		pinctrl: pinctrl@d0200 {
+			compatible = "marvell,dove-pinctrl";
+			reg = <0xd0200 0x10>;
 		};
 
 		spi0: spi@10600 {

arch/arm/boot/dts/evk-pro3.dts

@@ -22,10 +22,22 @@ macb0: ethernet@fffc4000 {
 				status = "okay";
 			};
 
+			usart0: serial@fffb0000 {
+				status = "okay";
+			};
+
+			usart2: serial@fffb8000 {
+				status = "okay";
+			};
+
 			usb1: gadget@fffa4000 {
 				atmel,vbus-gpio = <&pioC 5 0>;
 				status = "okay";
 			};
+
+			watchdog@fffffd40 {
+				status = "okay";
+			};
 		};
 
 		usb0: ohci@00500000 {

arch/arm/boot/dts/exynos4.dtsi

@@ -28,6 +28,44 @@ aliases {
 		spi0 = &spi_0;
 		spi1 = &spi_1;
 		spi2 = &spi_2;
+		i2c0 = &i2c_0;
+		i2c1 = &i2c_1;
+		i2c2 = &i2c_2;
+		i2c3 = &i2c_3;
+		i2c4 = &i2c_4;
+		i2c5 = &i2c_5;
+		i2c6 = &i2c_6;
+		i2c7 = &i2c_7;
+	};
+
+	pd_mfc: mfc-power-domain@10023C40 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10023C40 0x20>;
+	};
+
+	pd_g3d: g3d-power-domain@10023C60 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10023C60 0x20>;
+	};
+
+	pd_lcd0: lcd0-power-domain@10023C80 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10023C80 0x20>;
+	};
+
+	pd_tv: tv-power-domain@10023C20 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10023C20 0x20>;
+	};
+
+	pd_cam: cam-power-domain@10023C00 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10023C00 0x20>;
+	};
+
+	pd_gps: gps-power-domain@10023CE0 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10023CE0 0x20>;
 	};
 
 	gic:interrupt-controller@10490000 {
@@ -121,7 +159,7 @@ serial@13830000 {
 		status = "disabled";
 	};
 
-	i2c@13860000 {
+	i2c_0: i2c@13860000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "samsung,s3c2440-i2c";
@@ -130,7 +168,7 @@ i2c@13860000 {
 		status = "disabled";
 	};
 
-	i2c@13870000 {
+	i2c_1: i2c@13870000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "samsung,s3c2440-i2c";
@@ -139,7 +177,7 @@ i2c@13870000 {
 		status = "disabled";
 	};
 
-	i2c@13880000 {
+	i2c_2: i2c@13880000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "samsung,s3c2440-i2c";
@@ -148,7 +186,7 @@ i2c@13880000 {
 		status = "disabled";
 	};
 
-	i2c@13890000 {
+	i2c_3: i2c@13890000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "samsung,s3c2440-i2c";
@@ -157,7 +195,7 @@ i2c@13890000 {
 		status = "disabled";
 	};
 
-	i2c@138A0000 {
+	i2c_4: i2c@138A0000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "samsung,s3c2440-i2c";
@@ -166,7 +204,7 @@ i2c@138A0000 {
 		status = "disabled";
 	};
 
-	i2c@138B0000 {
+	i2c_5: i2c@138B0000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "samsung,s3c2440-i2c";
@@ -175,7 +213,7 @@ i2c@138B0000 {
 		status = "disabled";
 	};
 
-	i2c@138C0000 {
+	i2c_6: i2c@138C0000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "samsung,s3c2440-i2c";
@@ -184,7 +222,7 @@ i2c@138C0000 {
 		status = "disabled";
 	};
 
-	i2c@138D0000 {
+	i2c_7: i2c@138D0000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "samsung,s3c2440-i2c";

arch/arm/boot/dts/exynos4210-origen.dts

@@ -22,38 +22,54 @@ / {
 	compatible = "insignal,origen", "samsung,exynos4210";
 
 	memory {
-		reg = <0x40000000 0x40000000>;
+		reg = <0x40000000 0x10000000
+		       0x50000000 0x10000000
+		       0x60000000 0x10000000
+		       0x70000000 0x10000000>;
 	};
 
 	chosen {
 		bootargs ="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC2,115200 init=/linuxrc";
 	};
 
+	mmc_reg: voltage-regulator {
+	        compatible = "regulator-fixed";
+		regulator-name = "VMEM_VDD_2.8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpx1 1 0>;
+		enable-active-high;
+	};
+
 	sdhci@12530000 {
-		samsung,sdhci-bus-width = <4>;
-		linux,mmc_cap_4_bit_data;
-		samsung,sdhci-cd-internal;
-		gpio-cd = <&gpk2 2 2 3 3>;
-		gpios = <&gpk2 0 2 0 3>,
-			<&gpk2 1 2 0 3>,
-			<&gpk2 3 2 3 3>,
-			<&gpk2 4 2 3 3>,
-			<&gpk2 5 2 3 3>,
-			<&gpk2 6 2 3 3>;
+		bus-width = <4>;
+		pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
+		pinctrl-names = "default";
+		vmmc-supply = <&mmc_reg>;
 		status = "okay";
 	};
 
 	sdhci@12510000 {
-		samsung,sdhci-bus-width = <4>;
-		linux,mmc_cap_4_bit_data;
-		samsung,sdhci-cd-internal;
-		gpio-cd = <&gpk0 2 2 3 3>;
-		gpios = <&gpk0 0 2 0 3>,
-			<&gpk0 1 2 0 3>,
-			<&gpk0 3 2 3 3>,
-			<&gpk0 4 2 3 3>,
-			<&gpk0 5 2 3 3>,
-			<&gpk0 6 2 3 3>;
+		bus-width = <4>;
+		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_cd>;
+		pinctrl-names = "default";
+		vmmc-supply = <&mmc_reg>;
+		status = "okay";
+	};
+
+	serial@13800000 {
+		status = "okay";
+	};
+
+	serial@13810000 {
+		status = "okay";
+	};
+
+	serial@13820000 {
+		status = "okay";
+	};
+
+	serial@13830000 {
 		status = "okay";
 	};
 
@@ -64,35 +80,35 @@ gpio_keys {
 
 		up {
 			label = "Up";
-			gpios = <&gpx2 0 0 0x10000 2>;
+			gpios = <&gpx2 0 1>;
 			linux,code = <103>;
 			gpio-key,wakeup;
 		};
 
 		down {
 			label = "Down";
-			gpios = <&gpx2 1 0 0x10000 2>;
+			gpios = <&gpx2 1 1>;
 			linux,code = <108>;
 			gpio-key,wakeup;
 		};
 
 		back {
 			label = "Back";
-			gpios = <&gpx1 7 0 0x10000 2>;
+			gpios = <&gpx1 7 1>;
 			linux,code = <158>;
 			gpio-key,wakeup;
 		};
 
 		home {
 			label = "Home";
-			gpios = <&gpx1 6 0 0x10000 2>;
+			gpios = <&gpx1 6 1>;
 			linux,code = <102>;
 			gpio-key,wakeup;
 		};
 
 		menu {
 			label = "Menu";
-			gpios = <&gpx1 5 0 0x10000 2>;
+			gpios = <&gpx1 5 1>;
 			linux,code = <139>;
 			gpio-key,wakeup;
 		};
@@ -101,7 +117,7 @@ menu {
 	leds {
 		compatible = "gpio-leds";
 		status {
-			gpios = <&gpx1 3 0 0x10000 2>;
+			gpios = <&gpx1 3 1>;
 			linux,default-trigger = "heartbeat";
 		};
 	};

arch/arm/boot/dts/exynos4210-pinctrl.dtsi

@@ -482,196 +482,196 @@ sd0_clk: sd0-clk {
 			samsung,pins = "gpk0-0";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd0_cmd: sd0-cmd {
 			samsung,pins = "gpk0-1";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd0_cd: sd0-cd {
 			samsung,pins = "gpk0-2";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd0_bus1: sd0-bus-width1 {
 			samsung,pins = "gpk0-3";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd0_bus4: sd0-bus-width4 {
 			samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd0_bus8: sd0-bus-width8 {
 			samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 			samsung,pin-function = <3>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd4_clk: sd4-clk {
 			samsung,pins = "gpk0-0";
 			samsung,pin-function = <3>;
 			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd4_cmd: sd4-cmd {
 			samsung,pins = "gpk0-1";
 			samsung,pin-function = <3>;
 			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd4_cd: sd4-cd {
 			samsung,pins = "gpk0-2";
 			samsung,pin-function = <3>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd4_bus1: sd4-bus-width1 {
 			samsung,pins = "gpk0-3";
 			samsung,pin-function = <3>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd4_bus4: sd4-bus-width4 {
 			samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
 			samsung,pin-function = <3>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd4_bus8: sd4-bus-width8 {
 			samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 			samsung,pin-function = <3>;
 			samsung,pin-pud = <4>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd1_clk: sd1-clk {
 			samsung,pins = "gpk1-0";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd1_cmd: sd1-cmd {
 			samsung,pins = "gpk1-1";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd1_cd: sd1-cd {
 			samsung,pins = "gpk1-2";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd1_bus1: sd1-bus-width1 {
 			samsung,pins = "gpk1-3";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd1_bus4: sd1-bus-width4 {
 			samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd2_clk: sd2-clk {
 			samsung,pins = "gpk2-0";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd2_cmd: sd2-cmd {
 			samsung,pins = "gpk2-1";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd2_cd: sd2-cd {
 			samsung,pins = "gpk2-2";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd2_bus1: sd2-bus-width1 {
 			samsung,pins = "gpk2-3";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd2_bus4: sd2-bus-width4 {
 			samsung,pins = "gpk2-3", "gpk2-4", "gpk2-5", "gpk2-6";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd2_bus8: sd2-bus-width8 {
 			samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
 			samsung,pin-function = <3>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd3_clk: sd3-clk {
 			samsung,pins = "gpk3-0";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd3_cmd: sd3-cmd {
 			samsung,pins = "gpk3-1";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <0>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd3_cd: sd3-cd {
 			samsung,pins = "gpk3-2";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd3_bus1: sd3-bus-width1 {
 			samsung,pins = "gpk3-3";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		sd3_bus4: sd3-bus-width4 {
 			samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <3>;
-			samsung,pin-drv = <0>;
+			samsung,pin-drv = <3>;
 		};
 
 		eint0: ext-int0 {

arch/arm/boot/dts/exynos4210-smdkv310.dts

@@ -43,6 +43,22 @@ sdhci@12530000 {
 		status = "okay";
 	};
 
+	serial@13800000 {
+		status = "okay";
+	};
+
+	serial@13810000 {
+		status = "okay";
+	};
+
+	serial@13820000 {
+		status = "okay";
+	};
+
+	serial@13830000 {
+		status = "okay";
+	};
+
 	keypad@100A0000 {
 		samsung,keypad-num-rows = <2>;
 		samsung,keypad-num-columns = <8>;

arch/arm/boot/dts/exynos4210-trats.dts

@@ -35,24 +35,15 @@ vemmc_reg: voltage-regulator@0 {
 		regulator-name = "VMEM_VDD_2.8V";
 		regulator-min-microvolt = <2800000>;
 		regulator-max-microvolt = <2800000>;
-		gpio = <&gpk0 2 1 0 0>;
+		gpio = <&gpk0 2 0>;
 		enable-active-high;
 	};
 
 	sdhci_emmc: sdhci@12510000 {
 		bus-width = <8>;
 		non-removable;
-		broken-voltage;
-		gpios = <&gpk0 0 2 0 3>,
-			<&gpk0 1 2 0 3>,
-			<&gpk0 3 2 2 3>,
-			<&gpk0 4 2 2 3>,
-			<&gpk0 5 2 2 3>,
-			<&gpk0 6 2 2 3>,
-			<&gpk1 3 3 3 3>,
-			<&gpk1 4 3 3 3>,
-			<&gpk1 5 3 3 3>,
-			<&gpk1 6 3 3 3>;
+		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
+		pinctrl-names = "default";
 		vmmc-supply = <&vemmc_reg>;
 		status = "okay";
 	};
@@ -73,12 +64,74 @@ serial@13830000 {
 		status = "okay";
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		vol-down-key {
+			gpios = <&gpx2 1 1>;
+			linux,code = <114>;
+			label = "volume down";
+			debounce-interval = <10>;
+		};
+
+		vol-up-key {
+			gpios = <&gpx2 0 1>;
+			linux,code = <115>;
+			label = "volume up";
+			debounce-interval = <10>;
+		};
+
+		power-key {
+			gpios = <&gpx2 7 1>;
+			linux,code = <116>;
+			label = "power";
+			debounce-interval = <10>;
+			gpio-key,wakeup;
+		};
+
+		ok-key {
+			gpios = <&gpx3 5 1>;
+			linux,code = <352>;
+			label = "ok";
+			debounce-interval = <10>;
+		};
+	};
+
+	tsp_reg: voltage-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "TSP_FIXED_VOLTAGES";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpl0 3 0>;
+		enable-active-high;
+	};
+
+	i2c@13890000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-slave-addr = <0x10>;
+		samsung,i2c-max-bus-freq = <400000>;
+		pinctrl-0 = <&i2c3_bus>;
+		pinctrl-names = "default";
+		status = "okay";
+
+		mms114-touchscreen@48 {
+			compatible = "melfas,mms114";
+			reg = <0x48>;
+			interrupt-parent = <&gpx0>;
+			interrupts = <4 2>;
+			x-size = <720>;
+			y-size = <1280>;
+			avdd-supply = <&tsp_reg>;
+			vdd-supply = <&tsp_reg>;
+		};
+	};
+
 	i2c@138B0000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-slave-addr = <0x10>;
 		samsung,i2c-max-bus-freq = <100000>;
-		gpios = <&gpb 6 3 3 0>,
-			<&gpb 7 3 3 0>;
+		pinctrl-0 = <&i2c5_bus>;
+		pinctrl-names = "default";
 		status = "okay";
 
 		max8997_pmic@66 {
@@ -93,9 +146,9 @@ max8997_pmic@66 {
 			max8997,pmic-ignore-gpiodvs-side-effect;
 			max8997,pmic-buck125-default-dvs-idx = <0>;
 
-			max8997,pmic-buck125-dvs-gpios = <&gpx0 5 1 0 0>,
-						         <&gpx0 6 1 0 0>,
-							 <&gpl0 0 1 0 0>;
+			max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>,
+						         <&gpx0 6 0>,
+							 <&gpl0 0 0>;
 
 			max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
 							 <1250000>, <1200000>,

arch/arm/boot/dts/exynos4210.dtsi

@@ -31,6 +31,11 @@ aliases {
 		pinctrl2 = &pinctrl_2;
 	};
 
+	pd_lcd1: lcd1-power-domain@10023CA0 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10023CA0 0x20>;
+	};
+
 	gic:interrupt-controller@10490000 {
 		cpu-offset = <0x8000>;
 	};
@@ -64,4 +69,11 @@ pinctrl_2: pinctrl@03860000 {
 		compatible = "samsung,pinctrl-exynos4210";
 		reg = <0x03860000 0x1000>;
 	};
+
+	tmu@100C0000 {
+		compatible = "samsung,exynos4210-tmu";
+		interrupt-parent = <&combiner>;
+		reg = <0x100C0000 0x100>;
+		interrupts = <2 4>;
+	};
 };

arch/arm/boot/dts/exynos4212.dtsi

+/*
+ * Samsung's Exynos4212 SoC device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos4212 SoC device nodes are listed in this file. Exynos4212
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos4212 SoC. As device tree coverage for Exynos4212 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/include/ "exynos4x12.dtsi"
+
+/ {
+	compatible = "samsung,exynos4212";
+
+	gic:interrupt-controller@10490000 {
+		cpu-offset = <0x8000>;
+	};
+};

arch/arm/boot/dts/exynos4412-smdk4412.dts

+/*
+ * Samsung's Exynos4412 based SMDK board device tree source
+ *
+ * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Device tree source file for Samsung's SMDK4412 board which is based on
+ * Samsung's Exynos4412 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ "exynos4412.dtsi"
+
+/ {
+	model = "Samsung SMDK evaluation board based on Exynos4412";
+	compatible = "samsung,smdk4412", "samsung,exynos4412";
+
+	memory {
+		reg = <0x40000000 0x40000000>;
+	};
+
+	chosen {
+		bootargs ="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC1,115200 init=/linuxrc";
+	};
+
+	serial@13800000 {
+		status = "okay";
+	};
+
+	serial@13810000 {
+		status = "okay";
+	};
+
+	serial@13820000 {
+		status = "okay";
+	};
+
+	serial@13830000 {
+		status = "okay";
+	};
+};

arch/arm/boot/dts/exynos4412.dtsi

+/*
+ * Samsung's Exynos4412 SoC device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos4412 SoC device nodes are listed in this file. Exynos4412
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos4412 SoC. As device tree coverage for Exynos4412 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/include/ "exynos4x12.dtsi"
+
+/ {
+	compatible = "samsung,exynos4412";
+
+	gic:interrupt-controller@10490000 {
+		cpu-offset = <0x4000>;
+	};
+};

arch/arm/boot/dts/exynos4x12.dtsi

+/*
+ * Samsung's Exynos4x12 SoCs device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos4x12 SoCs device nodes are listed in this file. Exynos4x12
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos4x12 SoC. As device tree coverage for Exynos4x12 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/include/ "exynos4.dtsi"
+/include/ "exynos4x12-pinctrl.dtsi"
+
+/ {
+	aliases {
+		pinctrl0 = &pinctrl_0;
+		pinctrl1 = &pinctrl_1;
+		pinctrl2 = &pinctrl_2;
+		pinctrl3 = &pinctrl_3;
+	};
+
+	combiner:interrupt-controller@10440000 {
+		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+			     <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+			     <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
+			     <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>;
+	};
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,pinctrl-exynos4x12";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+	};
+
+	pinctrl_1: pinctrl@11000000 {
+		compatible = "samsung,pinctrl-exynos4x12";
+		reg = <0x11000000 0x1000>;
+		interrupts = <0 46 0>;
+
+		wakup_eint: wakeup-interrupt-controller {
+			compatible = "samsung,exynos4210-wakeup-eint";
+			interrupt-parent = <&gic>;
+			interrupts = <0 32 0>;
+		};
+	};
+
+	pinctrl_2: pinctrl@03860000 {
+		compatible = "samsung,pinctrl-exynos4x12";
+		reg = <0x03860000 0x1000>;
+		interrupt-parent = <&combiner>;
+		interrupts = <10 0>;
+	};
+
+	pinctrl_3: pinctrl@106E0000 {
+		compatible = "samsung,pinctrl-exynos4x12";
+		reg = <0x106E0000 0x1000>;
+		interrupts = <0 72 0>;
+	};
+};

arch/arm/boot/dts/exynos5250-smdk5250.dts

@@ -17,10 +17,6 @@ / {
 	compatible = "samsung,smdk5250", "samsung,exynos5250";
 
 	aliases {
-		mshc0 = &dwmmc_0;
-		mshc1 = &dwmmc_1;
-		mshc2 = &dwmmc_2;
-		mshc3 = &dwmmc_3;
 	};
 
 	memory {
@@ -55,8 +51,31 @@ eeprom@51 {
 		};
 	};
 
+	i2c@121D0000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <40000>;
+		samsung,i2c-slave-addr = <0x38>;
+
+		sata-phy {
+			compatible = "samsung,sata-phy";
+			reg = <0x38>;
+		};
+	};
+
+	sata@122F0000 {
+		samsung,sata-freq = <66>;
+	};
+
 	i2c@12C80000 {
-		status = "disabled";
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <66000>;
+		gpios = <&gpa0 6 3 3 0>,
+			<&gpa0 7 3 3 0>;
+
+		hdmiddc@50 {
+			compatible = "samsung,exynos5-hdmiddc";
+			reg = <0x50>;
+		};
 	};
 
 	i2c@12C90000 {
@@ -79,7 +98,17 @@ i2c@12CD0000 {
 		status = "disabled";
 	};
 
-	dwmmc_0: dwmmc0@12200000 {
+	i2c@12CE0000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <66000>;
+
+		hdmiphy@38 {
+			compatible = "samsung,exynos5-hdmiphy";
+			reg = <0x38>;
+		};
+	};
+
+	dwmmc0@12200000 {
 		num-slots = <1>;
 		supports-highspeed;
 		broken-cd;
@@ -100,11 +129,11 @@ slot@0 {
 		};
 	};
 
-	dwmmc_1: dwmmc1@12210000 {
+	dwmmc1@12210000 {
 		status = "disabled";
 	};
 
-	dwmmc_2: dwmmc2@12220000 {
+	dwmmc2@12220000 {
 		num-slots = <1>;
 		supports-highspeed;
 		fifo-depth = <0x80>;
@@ -125,7 +154,7 @@ slot@0 {
 		};
 	};
 
-	dwmmc_3: dwmmc3@12230000 {
+	dwmmc3@12230000 {
 		status = "disabled";
 	};
 
@@ -166,4 +195,13 @@ partition@40000 {
 	spi_2: spi@12d40000 {
 		status = "disabled";
 	};
+
+	hdmi {
+		hpd-gpio = <&gpx3 7 0xf 1 3>;
+	};
+
+	codec@11000000 {
+		samsung,mfc-r = <0x43000000 0x800000>;
+		samsung,mfc-l = <0x51000000 0x800000>;
+	};
 };

arch/arm/boot/dts/exynos5250-snow.dts

+/*
+ * Google Snow board device tree source
+ *
+ * Copyright (c) 2012 Google, Inc
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ "exynos5250.dtsi"
+/include/ "cros5250-common.dtsi"
+
+/ {
+	model = "Google Snow";
+	compatible = "google,snow", "samsung,exynos5250";
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		lid-switch {
+			label = "Lid";
+			gpios = <&gpx3 5 0 0x10000 0>;
+			linux,input-type = <5>; /* EV_SW */
+			linux,code = <0>; /* SW_LID */
+			debounce-interval = <1>;
+			gpio-key,wakeup;
+		};
+	};
+
+	/*
+	 * On Snow we've got SIP WiFi and so can keep drive strengths low to
+	 * reduce EMI.
+	 */
+	dwmmc3@12230000 {
+		slot@0 {
+			gpios = <&gpc4 0 2 0 0>, <&gpc4 1 2 3 0>,
+				<&gpc4 3 2 3 0>, <&gpc4 4 2 3 0>,
+				<&gpc4 5 2 3 0>, <&gpc4 6 2 3 0>;
+		};
+	};
+};

arch/arm/boot/dts/exynos5250.dtsi

@@ -31,6 +31,10 @@ aliases {
 		gsc1 = &gsc_1;
 		gsc2 = &gsc_2;
 		gsc3 = &gsc_3;
+		mshc0 = &dwmmc_0;
+		mshc1 = &dwmmc_1;
+		mshc2 = &dwmmc_2;
+		mshc3 = &dwmmc_3;
 	};
 
 	gic:interrupt-controller@10481000 {
@@ -62,12 +66,24 @@ watchdog {
 		interrupts = <0 42 0>;
 	};
 
+	codec@11000000 {
+		compatible = "samsung,mfc-v6";
+		reg = <0x11000000 0x10000>;
+		interrupts = <0 96 0>;
+	};
+
 	rtc {
 		compatible = "samsung,s3c6410-rtc";
 		reg = <0x101E0000 0x100>;
 		interrupts = <0 43 0>, <0 44 0>;
 	};
 
+	tmu@10060000 {
+		compatible = "samsung,exynos5250-tmu";
+		reg = <0x10060000 0x100>;
+		interrupts = <0 65 0>;
+	};
+
 	serial@12C00000 {
 		compatible = "samsung,exynos4210-uart";
 		reg = <0x12C00000 0x100>;
@@ -92,6 +108,17 @@ serial@12C30000 {
 		interrupts = <0 54 0>;
 	};
 
+	sata@122F0000 {
+		compatible = "samsung,exynos5-sata-ahci";
+		reg = <0x122F0000 0x1ff>;
+		interrupts = <0 115 0>;
+	};
+
+	sata-phy@12170000 {
+		compatible = "samsung,exynos5-sata-phy";
+		reg = <0x12170000 0x1ff>;
+	};
+
 	i2c@12C60000 {
 		compatible = "samsung,s3c2440-i2c";
 		reg = <0x12C60000 0x100>;
@@ -156,6 +183,21 @@ i2c@12CD0000 {
 		#size-cells = <0>;
 	};
 
+	i2c@12CE0000 {
+		compatible = "samsung,s3c2440-hdmiphy-i2c";
+		reg = <0x12CE0000 0x1000>;
+		interrupts = <0 64 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	i2c@121D0000 {
+                compatible = "samsung,exynos5-sata-phy-i2c";
+                reg = <0x121D0000 0x100>;
+                #address-cells = <1>;
+                #size-cells = <0>;
+	};
+
 	spi_0: spi@12d20000 {
 		compatible = "samsung,exynos4210-spi";
 		reg = <0x12d20000 0x100>;
@@ -186,7 +228,7 @@ spi_2: spi@12d40000 {
 		#size-cells = <0>;
 	};
 
-	dwmmc0@12200000 {
+	dwmmc_0: dwmmc0@12200000 {
 		compatible = "samsung,exynos5250-dw-mshc";
 		reg = <0x12200000 0x1000>;
 		interrupts = <0 75 0>;
@@ -194,7 +236,7 @@ dwmmc0@12200000 {
 		#size-cells = <0>;
 	};
 
-	dwmmc1@12210000 {
+	dwmmc_1: dwmmc1@12210000 {
 		compatible = "samsung,exynos5250-dw-mshc";
 		reg = <0x12210000 0x1000>;
 		interrupts = <0 76 0>;
@@ -202,7 +244,7 @@ dwmmc1@12210000 {
 		#size-cells = <0>;
 	};
 
-	dwmmc2@12220000 {
+	dwmmc_2: dwmmc2@12220000 {
 		compatible = "samsung,exynos5250-dw-mshc";
 		reg = <0x12220000 0x1000>;
 		interrupts = <0 77 0>;
@@ -210,7 +252,7 @@ dwmmc2@12220000 {
 		#size-cells = <0>;
 	};
 
-	dwmmc3@12230000 {
+	dwmmc_3: dwmmc3@12230000 {
 		compatible = "samsung,exynos5250-dw-mshc";
 		reg = <0x12230000 0x1000>;
 		interrupts = <0 78 0>;
@@ -520,4 +562,16 @@ gsc_3:  gsc@0x13e30000 {
 		reg = <0x13e30000 0x1000>;
 		interrupts = <0 88 0>;
 	};
+
+	hdmi {
+		compatible = "samsung,exynos5-hdmi";
+		reg = <0x14530000 0x100000>;
+		interrupts = <0 95 0>;
+	};
+
+	mixer {
+		compatible = "samsung,exynos5-mixer";
+		reg = <0x14450000 0x10000>;
+		interrupts = <0 94 0>;
+	};
 };

arch/arm/boot/dts/href.dtsi

+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "dbx5x0.dtsi"
+
+/ {
+	memory {
+		reg = <0x00000000 0x20000000>;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		button@1 {
+			linux,code = <11>;
+			label = "SFH7741 Proximity Sensor";
+		};
+	};
+
+	soc-u9500 {
+		uart@80120000 {
+			status = "okay";
+		};
+
+		uart@80121000 {
+			status = "okay";
+		};
+
+		uart@80007000 {
+			status = "okay";
+		};
+
+		i2c@80004000 {
+			tc3589x@42 {
+				compatible = "tc3589x";
+				reg = <0x42>;
+				interrupt-parent = <&gpio6>;
+				interrupts = <25 0x1>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				tc3589x_gpio: tc3589x_gpio {
+					compatible = "tc3589x-gpio";
+					interrupts = <0 0x1>;
+
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+			};
+		};
+
+		i2c@80128000 {
+			lp5521@0x33 {
+				compatible = "lp5521";
+				reg = <0x33>;
+			};
+
+			lp5521@0x34 {
+				compatible = "lp5521";
+				reg = <0x34>;
+			};
+
+			bh1780@0x29 {
+				compatible = "rohm,bh1780gli";
+				reg = <0x33>;
+			};
+		};
+
+		// External Micro SD slot
+		sdi0_per1@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			mmc-cap-sd-highspeed;
+			mmc-cap-mmc-highspeed;
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+
+			cd-gpios  = <&tc3589x_gpio 3 0x4>;
+
+			status = "okay";
+		};
+
+		// WLAN SDIO channel
+		sdi1_per2@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+
+			status = "okay";
+		};
+
+		// PoP:ed eMMC
+		sdi2_per3@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <8>;
+			mmc-cap-mmc-highspeed;
+
+			status = "okay";
+		};
+
+		// On-board eMMC
+		sdi4_per2@80114000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <50000000>;
+			bus-width = <8>;
+			mmc-cap-mmc-highspeed;
+			vmmc-supply = <&ab8500_ldo_aux2_reg>;
+
+			status = "okay";
+		};
+
+		sound {
+			compatible = "stericsson,snd-soc-mop500";
+
+			stericsson,cpu-dai = <&msp1 &msp3>;
+			stericsson,audio-codec = <&codec>;
+		};
+
+		msp1: msp@80124000 {
+			status = "okay";
+		};
+
+		msp3: msp@80125000 {
+			status = "okay";
+		};
+
+		prcmu@80157000 {
+			db8500-prcmu-regulators {
+				db8500_vape_reg: db8500_vape {
+					regulator-name = "db8500-vape";
+				};
+
+				db8500_varm_reg: db8500_varm {
+					regulator-name = "db8500-varm";
+				};
+
+				db8500_vmodem_reg: db8500_vmodem {
+					regulator-name = "db8500-vmodem";
+				};
+
+				db8500_vpll_reg: db8500_vpll {
+					regulator-name = "db8500-vpll";
+				};
+
+				db8500_vsmps1_reg: db8500_vsmps1 {
+					regulator-name = "db8500-vsmps1";
+				};
+
+				db8500_vsmps2_reg: db8500_vsmps2 {
+					regulator-name = "db8500-vsmps2";
+				};
+
+				db8500_vsmps3_reg: db8500_vsmps3 {
+					regulator-name = "db8500-vsmps3";
+				};
+
+				db8500_vrf1_reg: db8500_vrf1 {
+					regulator-name = "db8500-vrf1";
+				};
+
+				db8500_sva_mmdsp_reg: db8500_sva_mmdsp {
+					regulator-name = "db8500-sva-mmdsp";
+				};
+
+				db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret {
+					regulator-name = "db8500-sva-mmdsp-ret";
+				};
+
+				db8500_sva_pipe_reg: db8500_sva_pipe {
+					regulator-name = "db8500_sva_pipe";
+				};
+
+				db8500_sia_mmdsp_reg: db8500_sia_mmdsp {
+					regulator-name = "db8500_sia_mmdsp";
+				};
+
+				db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret {
+					regulator-name = "db8500-sia-mmdsp-ret";
+				};
+
+				db8500_sia_pipe_reg: db8500_sia_pipe {
+					regulator-name = "db8500-sia-pipe";
+				};
+
+				db8500_sga_reg: db8500_sga {
+					regulator-name = "db8500-sga";
+				};
+
+				db8500_b2r2_mcde_reg: db8500_b2r2_mcde {
+					regulator-name = "db8500-b2r2-mcde";
+				};
+
+				db8500_esram12_reg: db8500_esram12 {
+					regulator-name = "db8500-esram12";
+				};
+
+				db8500_esram12_ret_reg: db8500_esram12_ret {
+					regulator-name = "db8500-esram12-ret";
+				};
+
+				db8500_esram34_reg: db8500_esram34 {
+					regulator-name = "db8500-esram34";
+				};
+
+				db8500_esram34_ret_reg: db8500_esram34_ret {
+					regulator-name = "db8500-esram34-ret";
+				};
+			};
+
+			ab8500@5 {
+				ab8500-regulators {
+					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
+						regulator-name = "V-DISPLAY";
+					};
+
+					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
+						regulator-name = "V-eMMC1";
+					};
+
+					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
+						regulator-name = "V-MMC-SD";
+					};
+
+					ab8500_ldo_initcore_reg: ab8500_ldo_initcore {
+						regulator-name = "V-INTCORE";
+					};
+
+					ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
+						regulator-name = "V-TVOUT";
+					};
+
+					ab8500_ldo_usb_reg: ab8500_ldo_usb {
+						regulator-name = "dummy";
+					};
+
+					ab8500_ldo_audio_reg: ab8500_ldo_audio {
+						regulator-name = "V-AUD";
+					};
+
+					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
+						regulator-name = "V-AMIC1";
+					};
+
+					ab8500_ldo_amamic2_reg: ab8500_ldo_amamic2 {
+						regulator-name = "V-AMIC2";
+					};
+
+					ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
+						regulator-name = "V-DMIC";
+					};
+
+					ab8500_ldo_ana_reg: ab8500_ldo_ana {
+						regulator-name = "V-CSI/DSI";
+					};
+				};
+			};
+		};
+	};
+};

arch/arm/boot/dts/hrefprev60.dts

+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "dbx5x0.dtsi"
+/include/ "href.dtsi"
+/include/ "stuib.dtsi"
+
+/ {
+	model = "ST-Ericsson HREF (pre-v60) platform with Device Tree";
+	compatible = "st-ericsson,mop500", "st-ericsson,u8500";
+
+	gpio_keys {
+		button@1 {
+			gpios = <&tc3589x_gpio 7 0x4>;
+		};
+	};
+
+	soc-u9500 {
+		i2c@80004000 {
+			tps61052@33 {
+				compatible = "tps61052";
+				reg = <0x33>;
+			};
+		};
+
+		i2c@80110000 {
+			bu21013_tp@0x5c {
+				reset-gpio = <&tc3589x_gpio 13 0x4>;
+			};
+		};
+
+		vmmci: regulator-gpio {
+			gpios = <&tc3589x_gpio 18 0x4>;
+			gpio-enable = <&tc3589x_gpio 17 0x4>;
+
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/hrefv60plus.dts

@@ -11,85 +11,200 @@
 
 /dts-v1/;
 /include/ "dbx5x0.dtsi"
+/include/ "href.dtsi"
+/include/ "stuib.dtsi"
 
 / {
-	model = "ST-Ericsson HREF platform with Device Tree";
-	compatible = "st-ericsson,hrefv60+";
+	model = "ST-Ericsson HREF (v60+) platform with Device Tree";
+	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
 
-	memory {
-		reg = <0x00000000 0x20000000>;
+	gpio_keys {
+		button@1 {
+			gpios = <&gpio6 25 0x4>;
+		};
 	};
 
 	soc-u9500 {
-		uart@80120000 {
+		i2c@80110000 {
+			bu21013_tp@0x5c {
+				reset-gpio = <&gpio4 15 0x4>;
+			};
+		};
+
+		// External Micro SD slot
+		sdi0_per1@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			mmc-cap-sd-highspeed;
+			mmc-cap-mmc-highspeed;
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+
+			cd-gpios  = <&tc3589x_gpio 3 0x4>;
+
 			status = "okay";
 		};
 
-		uart@80121000 {
+		// WLAN SDIO channel
+		sdi1_per2@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+
 			status = "okay";
 		};
 
-		uart@80007000 {
+		// PoP:ed eMMC
+		sdi2_per3@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <8>;
+			mmc-cap-mmc-highspeed;
+
 			status = "okay";
 		};
 
-		i2c@80004000 {
-			tc3589x@42 {
-				compatible = "tc3589x";
-				reg = <0x42>;
-				interrupt-parent = <&gpio6>;
-				interrupts = <25 0x1>;
+		// On-board eMMC
+		sdi4_per2@80114000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <50000000>;
+			bus-width = <8>;
+			mmc-cap-mmc-highspeed;
+			vmmc-supply = <&ab8500_ldo_aux2_reg>;
 
-				interrupt-controller;
-				#interrupt-cells = <2>;
+			status = "okay";
+		};
 
-				tc3589x_gpio: tc3589x_gpio {
-					compatible = "tc3589x-gpio";
-					interrupts = <0 0x1>;
+		prcmu@80157000 {
+			db8500-prcmu-regulators {
+				db8500_vape_reg: db8500_vape {
+					regulator-name = "db8500-vape";
+				};
 
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					#gpio-cells = <2>;
+				db8500_varm_reg: db8500_varm {
+					regulator-name = "db8500-varm";
 				};
+
+				db8500_vmodem_reg: db8500_vmodem {
+					regulator-name = "db8500-vmodem";
 				};
 
-			tps61052@33 {
-				compatible = "tps61052";
-				reg = <0x33>;
+				db8500_vpll_reg: db8500_vpll {
+					regulator-name = "db8500-vpll";
 				};
+
+				db8500_vsmps1_reg: db8500_vsmps1 {
+					regulator-name = "db8500-vsmps1";
 				};
 
-		i2c@80128000 {
-			lp5521@0x33 {
-				compatible = "lp5521";
-				reg = <0x33>;
+				db8500_vsmps2_reg: db8500_vsmps2 {
+					regulator-name = "db8500-vsmps2";
 				};
 
-			lp5521@0x34 {
-				compatible = "lp5521";
-				reg = <0x34>;
+				db8500_vsmps3_reg: db8500_vsmps3 {
+					regulator-name = "db8500-vsmps3";
 				};
 
-			bh1780@0x29 {
-				compatible = "rohm,bh1780gli";
-				reg = <0x33>;
+				db8500_vrf1_reg: db8500_vrf1 {
+					regulator-name = "db8500-vrf1";
 				};
+
+				db8500_sva_mmdsp_reg: db8500_sva_mmdsp {
+					regulator-name = "db8500-sva-mmdsp";
 				};
 
-		sound {
-			compatible = "stericsson,snd-soc-mop500";
+				db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret {
+					regulator-name = "db8500-sva-mmdsp-ret";
+				};
 
-			stericsson,cpu-dai = <&msp1 &msp3>;
-			stericsson,audio-codec = <&codec>;
+				db8500_sva_pipe_reg: db8500_sva_pipe {
+					regulator-name = "db8500_sva_pipe";
 				};
 
-		msp1: msp@80124000 {
-			status = "okay";
+				db8500_sia_mmdsp_reg: db8500_sia_mmdsp {
+					regulator-name = "db8500_sia_mmdsp";
 				};
 
-		msp3: msp@80125000 {
-			status = "okay";
+				db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret {
+					regulator-name = "db8500-sia-mmdsp-ret";
+				};
+
+				db8500_sia_pipe_reg: db8500_sia_pipe {
+					regulator-name = "db8500-sia-pipe";
+				};
+
+				db8500_sga_reg: db8500_sga {
+					regulator-name = "db8500-sga";
+				};
+
+				db8500_b2r2_mcde_reg: db8500_b2r2_mcde {
+					regulator-name = "db8500-b2r2-mcde";
+				};
+
+				db8500_esram12_reg: db8500_esram12 {
+					regulator-name = "db8500-esram12";
+				};
+
+				db8500_esram12_ret_reg: db8500_esram12_ret {
+					regulator-name = "db8500-esram12-ret";
+				};
+
+				db8500_esram34_reg: db8500_esram34 {
+					regulator-name = "db8500-esram34";
+				};
+
+				db8500_esram34_ret_reg: db8500_esram34_ret {
+					regulator-name = "db8500-esram34-ret";
+				};
+			};
+
+			ab8500@5 {
+				ab8500-regulators {
+					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
+						regulator-name = "V-DISPLAY";
+					};
+
+					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
+						regulator-name = "V-eMMC1";
+					};
+
+					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
+						regulator-name = "V-MMC-SD";
+					};
+
+					ab8500_ldo_initcore_reg: ab8500_ldo_initcore {
+						regulator-name = "V-INTCORE";
+					};
+
+					ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
+						regulator-name = "V-TVOUT";
+					};
+
+					ab8500_ldo_usb_reg: ab8500_ldo_usb {
+						regulator-name = "dummy";
+					};
+
+					ab8500_ldo_audio_reg: ab8500_ldo_audio {
+						regulator-name = "V-AUD";
+					};
+
+					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
+						regulator-name = "V-AMIC1";
+					};
+
+					ab8500_ldo_amamic2_reg: ab8500_ldo_amamic2 {
+						regulator-name = "V-AMIC2";
+					};
+
+					ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
+						regulator-name = "V-DMIC";
+					};
+
+					ab8500_ldo_ana_reg: ab8500_ldo_ana {
+						regulator-name = "V-CSI/DSI";
+					};
+				};
+			};
 		};
 	};
 };

arch/arm/boot/dts/imx23-olinuxino.dts

@@ -40,6 +40,15 @@ hog_pins_a: hog@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x2013 /* MX23_PAD_SSP1_DETECT__GPIO_2_1 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				led_pin_gpio0_17: led_gpio0_17@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x0113 /* MX23_PAD_GPMI_ALE__GPIO_0_17 */
 					>;
 					fsl,drive-strength = <0>;
@@ -47,6 +56,15 @@ hog_pins_a: hog@0 {
 					fsl,pull-up = <0>;
 				};
 			};
+
+			ssp1: ssp@80034000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx23-spi";
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi2_pins_a>;
+				status = "okay";
+			};
 		};
 
 		apbx@80040000 {
@@ -91,11 +109,12 @@ reg_usb0_vbus: usb0_vbus {
 
 	leds {
 		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pin_gpio0_17>;
 
 		user {
 			label = "green";
-			gpios = <&gpio2 1 0>;
-			linux,default-trigger = "default-on";
+			gpios = <&gpio2 1 1>;
 		};
 	};
 };

arch/arm/boot/dts/imx23.dtsi

@@ -279,6 +279,19 @@ lcdif_24bit_pins_a: lcdif-24bit@0 {
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
+
+				spi2_pins_a: spi2@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x0182 /* MX23_PAD_GPMI_WRN__SSP2_SCK */
+						0x0142 /* MX23_PAD_GPMI_RDY1__SSP2_CMD */
+						0x0002 /* MX23_PAD_GPMI_D00__SSP2_DATA0 */
+						0x0032 /* MX23_PAD_GPMI_D03__SSP2_DATA3 */
+					>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
 			};
 
 			digctl@8001c000 {

arch/arm/boot/dts/imx25-karo-tx25.dts

+/*
+ * Copyright 2012 Sascha Hauer, Pengutronix
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx25.dtsi"
+
+/ {
+	model = "Ka-Ro TX25";
+	compatible = "karo,imx25-tx25", "fsl,imx25";
+
+	memory {
+		reg = <0x80000000 0x02000000 0x90000000 0x02000000>;
+	};
+
+	soc {
+		aips@43f00000 {
+			uart1: serial@43f90000 {
+				status = "okay";
+			};
+		};
+
+		spba@50000000 {
+			fec: ethernet@50038000 {
+				status = "okay";
+				phy-mode = "rmii";
+			};
+		};
+
+		emi@80000000 {
+			nand@bb000000 {
+				nand-on-flash-bbt;
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/imx27-apf27.dts

+/*
+ * Copyright 2012 Philippe Reynes <tremyfr@yahoo.fr>
+ * Copyright 2012 Armadeus Systems <support@armadeus.com>
+ *
+ * Based on code which is: Copyright 2012 Sascha Hauer, Pengutronix
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx27.dtsi"
+
+/ {
+	model = "Armadeus Systems APF27 module";
+	compatible = "armadeus,imx27-apf27", "fsl,imx27";
+
+	memory {
+		reg = <0xa0000000 0x04000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		osc26m {
+			compatible = "fsl,imx-osc26m", "fixed-clock";
+			clock-frequency = <0>;
+		};
+	};
+
+	soc {
+		aipi@10000000 {
+			serial@1000a000 {
+				status = "okay";
+			};
+
+			ethernet@1002b000 {
+				status = "okay";
+			};
+		};
+
+		nand@d8000000 {
+			status = "okay";
+			nand-bus-width = <16>;
+			nand-ecc-mode = "hw";
+			nand-on-flash-bbt;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x100000>;
+			};
+
+			partition@100000 {
+				label = "env";
+				reg = <0x100000 0x80000>;
+			};
+
+			partition@180000 {
+				label = "env2";
+				reg = <0x180000 0x80000>;
+			};
+
+			partition@200000 {
+				label = "firmware";
+				reg = <0x200000 0x80000>;
+			};
+
+			partition@280000 {
+				label = "dtb";
+				reg = <0x280000 0x80000>;
+			};
+
+			partition@300000 {
+				label = "kernel";
+				reg = <0x300000 0x500000>;
+			};
+
+			partition@800000 {
+				label = "rootfs";
+				reg = <0x800000 0xf800000>;
+			};
+		};
+	};
+};

arch/arm/boot/dts/imx27.dtsi

@@ -58,7 +58,7 @@ aipi@10000000 { /* AIPI1 */
 			reg = <0x10000000 0x10000000>;
 			ranges;
 
-			wdog@10002000 {
+			wdog: wdog@10002000 {
 				compatible = "fsl,imx27-wdt", "fsl,imx21-wdt";
 				reg = <0x10002000 0x4000>;
 				interrupts = <27>;
@@ -218,7 +218,8 @@ fec: ethernet@1002b000 {
 				status = "disabled";
 			};
 		};
-		nand@d8000000 {
+
+		nfc: nand@d8000000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 

arch/arm/boot/dts/imx28-apf28.dts

+/*
+ * Copyright 2012 Armadeus Systems - <support@armadeus.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx28.dtsi"
+
+/ {
+	model = "Armadeus Systems APF28 module";
+	compatible = "armadeus,imx28-apf28", "fsl,imx28";
+
+	memory {
+		reg = <0x40000000 0x08000000>;
+	};
+
+	apb@80000000 {
+		apbh@80000000 {
+			gpmi-nand@8000c000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+				status = "okay";
+
+				partition@0 {
+					label = "u-boot";
+					reg = <0x0 0x300000>;
+				};
+
+				partition@300000 {
+					label = "env";
+					reg = <0x300000 0x80000>;
+				};
+
+				partition@380000 {
+					label = "env2";
+					reg = <0x380000 0x80000>;
+				};
+
+				partition@400000 {
+					label = "dtb";
+					reg = <0x400000 0x80000>;
+				};
+
+				partition@480000 {
+					label = "splash";
+					reg = <0x480000 0x80000>;
+				};
+
+				partition@500000 {
+					label = "kernel";
+					reg = <0x500000 0x800000>;
+				};
+
+				partition@d00000 {
+					label = "rootfs";
+					reg = <0xd00000 0xf300000>;
+				};
+			};
+		};
+
+		apbx@80040000 {
+			duart: serial@80074000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&duart_pins_a>;
+				status = "okay";
+			};
+		};
+	};
+
+	ahb@80080000 {
+		mac0: ethernet@800f0000 {
+			phy-mode = "rmii";
+			pinctrl-names = "default";
+			pinctrl-0 = <&mac0_pins_a>;
+			phy-reset-gpios = <&gpio4 13 0>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/imx28-apf28dev.dts

+/*
+ * Copyright 2012 Armadeus Systems - <support@armadeus.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/* APF28Dev is a docking board for the APF28 SOM */
+/include/ "imx28-apf28.dts"
+
+/ {
+	model = "Armadeus Systems APF28Dev docking/development board";
+	compatible = "armadeus,imx28-apf28dev", "armadeus,imx28-apf28", "fsl,imx28";
+
+	apb@80000000 {
+		apbh@80000000 {
+			ssp0: ssp@80010000 {
+				compatible = "fsl,imx28-mmc";
+				pinctrl-names = "default";
+				pinctrl-0 = <&mmc0_4bit_pins_a
+					&mmc0_cd_cfg &mmc0_sck_cfg>;
+				bus-width = <4>;
+				status = "okay";
+			};
+
+			ssp2: ssp@80014000 {
+				compatible = "fsl,imx28-spi";
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi2_pins_a>;
+				status = "okay";
+			};
+
+			pinctrl@80018000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&hog_pins_apf28dev>;
+
+				hog_pins_apf28dev: hog@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x1103 /* MX28_PAD_LCD_D16__GPIO_1_16 */
+						0x1113 /* MX28_PAD_LCD_D17__GPIO_1_17 */
+						0x1123 /* MX28_PAD_LCD_D18__GPIO_1_18 */
+						0x1133 /* MX28_PAD_LCD_D19__GPIO_1_19 */
+						0x1143 /* MX28_PAD_LCD_D20__GPIO_1_20 */
+						0x1153 /* MX28_PAD_LCD_D21__GPIO_1_21 */
+						0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				lcdif_pins_apf28dev: lcdif-apf28dev@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
+						0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
+						0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
+						0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+			};
+
+			lcdif@80030000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&lcdif_16bit_pins_a
+						&lcdif_pins_apf28dev>;
+				status = "okay";
+			};
+		};
+
+		apbx@80040000 {
+			lradc@80050000 {
+				status = "okay";
+			};
+
+			i2c0: i2c@80058000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c0_pins_a>;
+				status = "okay";
+			};
+
+			pwm: pwm@80064000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pwm3_pins_a &pwm4_pins_a>;
+				status = "okay";
+			};
+
+			usbphy0: usbphy@8007c000 {
+				status = "okay";
+			};
+
+			usbphy1: usbphy@8007e000 {
+				status = "okay";
+			};
+		};
+	};
+
+	ahb@80080000 {
+		usb0: usb@80080000 {
+			vbus-supply = <&reg_usb0_vbus>;
+			status = "okay";
+		};
+
+		usb1: usb@80090000 {
+			status = "okay";
+		};
+
+		mac1: ethernet@800f4000 {
+			phy-mode = "rmii";
+			pinctrl-names = "default";
+			pinctrl-0 = <&mac1_pins_a>;
+			phy-reset-gpios = <&gpio0 23 0>;
+			status = "okay";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_usb0_vbus: usb0_vbus {
+			compatible = "regulator-fixed";
+			regulator-name = "usb0_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio1 23 1>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		user {
+			label = "Heartbeat";
+			gpios = <&gpio0 21 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+
+		pwms = <&pwm 3 191000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+};

arch/arm/boot/dts/imx28-cfa10036.dts

@@ -22,6 +22,31 @@ memory {
 
 	apb@80000000 {
 		apbh@80000000 {
+			pinctrl@80018000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&hog_pins_cfa10036>;
+
+				hog_pins_cfa10036: hog-10036@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x2073 /* MX28_PAD_SSP0_D7__GPIO_2_7 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				led_pins_cfa10036: leds-10036@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x3043 /* MX28_PAD_AUART1_RX__GPIO_3_4 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+			};
+
 			ssp0: ssp@80010000 {
 				compatible = "fsl,imx28-mmc";
 				pinctrl-names = "default";
@@ -33,16 +58,37 @@ ssp0: ssp@80010000 {
 		};
 
 		apbx@80040000 {
+			pwm: pwm@80064000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pwm4_pins_a>;
+				status = "okay";
+			};
+
 			duart: serial@80074000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&duart_pins_b>;
 				status = "okay";
 			};
+
+			i2c0: i2c@80058000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c0_pins_b>;
+				status = "okay";
+
+				ssd1307: oled@3c {
+					compatible = "solomon,ssd1307fb-i2c";
+					reg = <0x3c>;
+					pwms = <&pwm 4 3000>;
+					reset-gpios = <&gpio2 7 0>;
+				};
+			};
 		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_cfa10036>;
 
 		power {
 			gpios = <&gpio3 4 1>;

arch/arm/boot/dts/imx28-cfa10049.dts

@@ -22,6 +22,22 @@ / {
 	apb@80000000 {
 		apbh@80000000 {
 			pinctrl@80018000 {
+				pinctrl-names = "default", "default";
+				pinctrl-1 = <&hog_pins_cfa10049>;
+
+				hog_pins_cfa10049: hog-10049@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+						0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */
+						0x1173 /* MX28_PAD_LCD_D22__GPIO_1_23 */
+						0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
 				spi3_pins_cfa10049: spi3-cfa10049@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -29,6 +45,7 @@ spi3_pins_cfa10049: spi3-cfa10049@0 {
 						0x01c1 /* MX28_PAD_GPMI_RESETN__SSP3_CMD */
 						0x0111 /* MX28_PAD_GPMI_CE1N__SSP3_D3 */
 						0x01a2 /* MX28_PAD_GPMI_ALE__SSP3_D4 */
+						0x01b2 /* MX28_PAD_GPMI_CLE__SSP3_D5 */
 					>;
 					fsl,drive-strength = <1>;
 					fsl,voltage = <1>;
@@ -60,6 +77,11 @@ gpio6: gpio6@1 {
 					spi-max-frequency = <100000>;
 				};
 
+				dac0: dh2228@2 {
+					compatible = "rohm,dh2228fv";
+					reg = <2>;
+					spi-max-frequency = <100000>;
+				};
 			};
 		};
 
@@ -96,4 +118,15 @@ reg_usb1_vbus: usb1_vbus {
 			gpio = <&gpio0 7 1>;
 		};
 	};
+
+	ahb@80080000 {
+		mac0: ethernet@800f0000 {
+			phy-mode = "rmii";
+			pinctrl-names = "default";
+			pinctrl-0 = <&mac0_pins_a>;
+			phy-reset-gpios = <&gpio2 21 0>;
+			phy-reset-duration = <100>;
+			status = "okay";
+		};
+	};
 };

arch/arm/boot/dts/imx28-evk.dts

@@ -76,7 +76,6 @@ hog_pins_a: hog@0 {
 						0x20c3 /* MX28_PAD_SSP1_SCK__GPIO_2_12 */
 						0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
 						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
-						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
 						0x3083 /* MX28_PAD_AUART2_RX__GPIO_3_8 */
 						0x3093 /* MX28_PAD_AUART2_TX__GPIO_3_9 */
 					>;
@@ -85,6 +84,16 @@ hog_pins_a: hog@0 {
 					fsl,pull-up = <0>;
 				};
 
+				led_pin_gpio3_5: led_gpio3_5@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
 				gpmi_pins_evk: gpmi-nand-evk@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -288,6 +297,8 @@ sound {
 
 	leds {
 		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pin_gpio3_5>;
 
 		user {
 			label = "Heartbeat";

arch/arm/boot/dts/lpc32xx.dtsi

@@ -182,6 +182,13 @@ i2c2: i2c@400A8000 {
 				pnx,timeout = <0x64>;
 			};
 
+			mpwm: mpwm@400E8000 {
+				compatible = "nxp,lpc3220-motor-pwm";
+				reg = <0x400E8000 0x78>;
+				status = "disabled";
+				#pwm-cells = <2>;
+			};
+
 			i2cusb: i2c@31020300 {
 				compatible = "nxp,pnx-i2c";
 				reg = <0x31020300 0x100>;

arch/arm/boot/dts/tegra20-plutux.dts

@@ -6,6 +6,12 @@ / {
 	model = "Avionic Design Plutux board";
 	compatible = "ad,plutux", "ad,tamonten", "nvidia,tegra20";
 
+	host1x {
+		hdmi {
+			status = "okay";
+		};
+	};
+
 	i2c@7000c000 {
 		wm8903: wm8903@1a {
 			compatible = "wlf,wm8903";