Commit df59c940 authored by Matt Carlson's avatar Matt Carlson Committed by David S. Miller

tg3: Move phylib report to end of tg3_init_one

Currently, phylib reports appear with a eth%d prefix.  Move the line
after register_netdev() and place it alongside the other informative
messages.  Update nearby informative messages accordingly.
Signed-off-by: default avatarMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: default avatarMichael Chan <mchan@broadcom.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent b2b98d4a
...@@ -1360,10 +1360,6 @@ static int tg3_phy_init(struct tg3 *tp) ...@@ -1360,10 +1360,6 @@ static int tg3_phy_init(struct tg3 *tp)
phydev->advertising = phydev->supported; phydev->advertising = phydev->supported;
printk(KERN_INFO
"%s: attached PHY driver [%s] (mii_bus:phy_addr=%s)\n",
tp->dev->name, phydev->drv->name, phydev->dev.bus_id);
return 0; return 0;
} }
...@@ -13547,26 +13543,34 @@ static int __devinit tg3_init_one(struct pci_dev *pdev, ...@@ -13547,26 +13543,34 @@ static int __devinit tg3_init_one(struct pci_dev *pdev,
goto err_out_apeunmap; goto err_out_apeunmap;
} }
printk(KERN_INFO "%s: Tigon3 [partno(%s) rev %04x PHY(%s)] " printk(KERN_INFO "%s: Tigon3 [partno(%s) rev %04x] (%s) MAC address %pM\n",
"(%s) %s Ethernet %pM\n",
dev->name, dev->name,
tp->board_part_number, tp->board_part_number,
tp->pci_chip_rev_id, tp->pci_chip_rev_id,
tg3_phy_string(tp),
tg3_bus_string(tp, str), tg3_bus_string(tp, str),
dev->dev_addr);
if (tp->tg3_flags3 & TG3_FLG3_PHY_CONNECTED)
printk(KERN_INFO
"%s: attached PHY driver [%s] (mii_bus:phy_addr=%s)\n",
tp->dev->name,
tp->mdio_bus->phy_map[PHY_ADDR]->drv->name,
tp->mdio_bus->phy_map[PHY_ADDR]->dev.bus_id);
else
printk(KERN_INFO
"%s: attached PHY is %s (%s Ethernet) (WireSpeed[%d])\n",
tp->dev->name, tg3_phy_string(tp),
((tp->tg3_flags & TG3_FLAG_10_100_ONLY) ? "10/100Base-TX" : ((tp->tg3_flags & TG3_FLAG_10_100_ONLY) ? "10/100Base-TX" :
((tp->tg3_flags2 & TG3_FLG2_ANY_SERDES) ? "1000Base-SX" : ((tp->tg3_flags2 & TG3_FLG2_ANY_SERDES) ? "1000Base-SX" :
"10/100/1000Base-T")), "10/100/1000Base-T")),
dev->dev_addr); (tp->tg3_flags2 & TG3_FLG2_NO_ETH_WIRE_SPEED) == 0);
printk(KERN_INFO "%s: RXcsums[%d] LinkChgREG[%d] " printk(KERN_INFO "%s: RXcsums[%d] LinkChgREG[%d] MIirq[%d] ASF[%d] TSOcap[%d]\n",
"MIirq[%d] ASF[%d] WireSpeed[%d] TSOcap[%d]\n",
dev->name, dev->name,
(tp->tg3_flags & TG3_FLAG_RX_CHECKSUMS) != 0, (tp->tg3_flags & TG3_FLAG_RX_CHECKSUMS) != 0,
(tp->tg3_flags & TG3_FLAG_USE_LINKCHG_REG) != 0, (tp->tg3_flags & TG3_FLAG_USE_LINKCHG_REG) != 0,
(tp->tg3_flags & TG3_FLAG_USE_MI_INTERRUPT) != 0, (tp->tg3_flags & TG3_FLAG_USE_MI_INTERRUPT) != 0,
(tp->tg3_flags & TG3_FLAG_ENABLE_ASF) != 0, (tp->tg3_flags & TG3_FLAG_ENABLE_ASF) != 0,
(tp->tg3_flags2 & TG3_FLG2_NO_ETH_WIRE_SPEED) == 0,
(tp->tg3_flags2 & TG3_FLG2_TSO_CAPABLE) != 0); (tp->tg3_flags2 & TG3_FLG2_TSO_CAPABLE) != 0);
printk(KERN_INFO "%s: dma_rwctrl[%08x] dma_mask[%d-bit]\n", printk(KERN_INFO "%s: dma_rwctrl[%08x] dma_mask[%d-bit]\n",
dev->name, tp->dma_rwctrl, dev->name, tp->dma_rwctrl,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment