Merge tag 'stm32-dt-for-v4.6-2' of...

Merge tag 'stm32-dt-for-v4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32 into next/dt

Merge "STM32 DT updates for v4.6 #2" from Maxime Coquelin:

Highlights:
-----------
 - Fix clock references in GPIO nodes
 - Add early support to stm32f469 MCU
 - Add USB HS support in host mdoe to stm32429-eval board
 - Add Ethernet support to stm32429-eval board

* tag 'stm32-dt-for-v4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32:
  ARM: dts: stm32f429: Enable Ethernet on Eval board
  ARM: dts: stm32f429: Add Ethernet support
  ARM: dts: stm32f429: Add system config bank node
  ARM: dts: stm32429i-eval: Add USB HS host mode support
  ARM: dts: stm32f429: Fix clocks referenced by GPIO banks
  ARM: stm32: Supply a DTS file for the STM32F469 Discovery board

arch/arm/boot/dts/Makefile

@@ -622,6 +622,7 @@ dtb-$(CONFIG_ARCH_STI) += \
 	stih418-b2199.dtb
 dtb-$(CONFIG_ARCH_STM32)+= \
 	stm32f429-disco.dtb \
+	stm32f469-disco.dtb \
 	stm32429i-eval.dtb
 dtb-$(CONFIG_MACH_SUN4I) += \
 	sun4i-a10-a1000.dtb \

arch/arm/boot/dts/stm32429i-eval.dts

@@ -81,14 +81,45 @@ blue {
 			gpios = <&gpiog 12 1>;
 		};
 	};
+
+	usbotg_hs_phy: usbphy {
+		#phy-cells = <0>;
+		compatible = "usb-nop-xceiv";
+		clocks = <&rcc 0 30>;
+		clock-names = "main_clk";
+	};
 };
 
 &clk_hse {
 	clock-frequency = <25000000>;
 };
 
+&ethernet0 {
+	status = "okay";
+	pinctrl-0	= <&ethernet0_mii>;
+	pinctrl-names	= "default";
+	phy-mode	= "mii-id";
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy1: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins_a>;
 	pinctrl-names = "default";
 	status = "okay";
 };
+
+&usbotg_hs {
+	dr_mode = "host";
+	phys = <&usbotg_hs_phy>;
+	phy-names = "usb2-phy";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};

arch/arm/boot/dts/stm32f429.dtsi

@@ -171,6 +171,11 @@ usart6: serial@40011400 {
 			status = "disabled";
 		};
 
+		syscfg: system-config@40013800 {
+			compatible = "syscon";
+			reg = <0x40013800 0x400>;
+		};
+
 		pin-controller {
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -182,7 +187,7 @@ gpioa: gpio@40020000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				reg = <0x0 0x400>;
-				clocks = <&rcc 0 256>;
+				clocks = <&rcc 0 0>;
 				st,bank-name = "GPIOA";
 			};
 
@@ -190,7 +195,7 @@ gpiob: gpio@40020400 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				reg = <0x400 0x400>;
-				clocks = <&rcc 0 257>;
+				clocks = <&rcc 0 1>;
 				st,bank-name = "GPIOB";
 			};
 
@@ -198,7 +203,7 @@ gpioc: gpio@40020800 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				reg = <0x800 0x400>;
-				clocks = <&rcc 0 258>;
+				clocks = <&rcc 0 2>;
 				st,bank-name = "GPIOC";
 			};
 
@@ -206,7 +211,7 @@ gpiod: gpio@40020c00 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				reg = <0xc00 0x400>;
-				clocks = <&rcc 0 259>;
+				clocks = <&rcc 0 3>;
 				st,bank-name = "GPIOD";
 			};
 
@@ -214,7 +219,7 @@ gpioe: gpio@40021000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				reg = <0x1000 0x400>;
-				clocks = <&rcc 0 260>;
+				clocks = <&rcc 0 4>;
 				st,bank-name = "GPIOE";
 			};
 
@@ -222,7 +227,7 @@ gpiof: gpio@40021400 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				reg = <0x1400 0x400>;
-				clocks = <&rcc 0 261>;
+				clocks = <&rcc 0 5>;
 				st,bank-name = "GPIOF";
 			};
 
@@ -230,7 +235,7 @@ gpiog: gpio@40021800 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				reg = <0x1800 0x400>;
-				clocks = <&rcc 0 262>;
+				clocks = <&rcc 0 6>;
 				st,bank-name = "GPIOG";
 			};
 
@@ -238,7 +243,7 @@ gpioh: gpio@40021c00 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				reg = <0x1c00 0x400>;
-				clocks = <&rcc 0 263>;
+				clocks = <&rcc 0 7>;
 				st,bank-name = "GPIOH";
 			};
 
@@ -246,7 +251,7 @@ gpioi: gpio@40022000 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				reg = <0x2000 0x400>;
-				clocks = <&rcc 0 264>;
+				clocks = <&rcc 0 8>;
 				st,bank-name = "GPIOI";
 			};
 
@@ -254,7 +259,7 @@ gpioj: gpio@40022400 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				reg = <0x2400 0x400>;
-				clocks = <&rcc 0 265>;
+				clocks = <&rcc 0 9>;
 				st,bank-name = "GPIOJ";
 			};
 
@@ -262,7 +267,7 @@ gpiok: gpio@40022800 {
 				gpio-controller;
 				#gpio-cells = <2>;
 				reg = <0x2800 0x400>;
-				clocks = <&rcc 0 266>;
+				clocks = <&rcc 0 10>;
 				st,bank-name = "GPIOK";
 			};
 
@@ -278,6 +283,46 @@ pins2 {
 					bias-disable;
 				};
 			};
+
+			usbotg_hs_pins_a: usbotg_hs@0 {
+				pins {
+					pinmux = <STM32F429_PH4_FUNC_OTG_HS_ULPI_NXT>,
+						 <STM32F429_PI11_FUNC_OTG_HS_ULPI_DIR>,
+						 <STM32F429_PC0_FUNC_OTG_HS_ULPI_STP>,
+						 <STM32F429_PA5_FUNC_OTG_HS_ULPI_CK>,
+						 <STM32F429_PA3_FUNC_OTG_HS_ULPI_D0>,
+						 <STM32F429_PB0_FUNC_OTG_HS_ULPI_D1>,
+						 <STM32F429_PB1_FUNC_OTG_HS_ULPI_D2>,
+						 <STM32F429_PB10_FUNC_OTG_HS_ULPI_D3>,
+						 <STM32F429_PB11_FUNC_OTG_HS_ULPI_D4>,
+						 <STM32F429_PB12_FUNC_OTG_HS_ULPI_D5>,
+						 <STM32F429_PB13_FUNC_OTG_HS_ULPI_D6>,
+						 <STM32F429_PB5_FUNC_OTG_HS_ULPI_D7>;
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+			};
+
+			ethernet0_mii: mii@0 {
+				pins {
+					pinmux = <STM32F429_PG13_FUNC_ETH_MII_TXD0_ETH_RMII_TXD0>,
+						 <STM32F429_PG14_FUNC_ETH_MII_TXD1_ETH_RMII_TXD1>,
+						 <STM32F429_PC2_FUNC_ETH_MII_TXD2>,
+						 <STM32F429_PB8_FUNC_ETH_MII_TXD3>,
+						 <STM32F429_PC3_FUNC_ETH_MII_TX_CLK>,
+						 <STM32F429_PG11_FUNC_ETH_MII_TX_EN_ETH_RMII_TX_EN>,
+						 <STM32F429_PA2_FUNC_ETH_MDIO>,
+						 <STM32F429_PC1_FUNC_ETH_MDC>,
+						 <STM32F429_PA1_FUNC_ETH_MII_RX_CLK_ETH_RMII_REF_CLK>,
+						 <STM32F429_PA7_FUNC_ETH_MII_RX_DV_ETH_RMII_CRS_DV>,
+						 <STM32F429_PC4_FUNC_ETH_MII_RXD0_ETH_RMII_RXD0>,
+						 <STM32F429_PC5_FUNC_ETH_MII_RXD1_ETH_RMII_RXD1>,
+						 <STM32F429_PH6_FUNC_ETH_MII_RXD2>,
+						 <STM32F429_PH7_FUNC_ETH_MII_RXD3>;
+					slew-rate = <2>;
+				};
+			};
 		};
 
 		rcc: rcc@40023810 {
@@ -318,6 +363,31 @@ dma2: dma-controller@40026400 {
 			st,mem2mem;
 		};
 
+		ethernet0: dwmac@40028000 {
+			compatible = "st,stm32-dwmac", "snps,dwmac-3.50a";
+			reg = <0x40028000 0x8000>;
+			reg-names = "stmmaceth";
+			interrupts = <61>, <62>;
+			interrupt-names = "macirq", "eth_wake_irq";
+			clock-names = "stmmaceth", "tx-clk", "rx-clk";
+			clocks = <&rcc 0 25>, <&rcc 0 26>, <&rcc 0 27>;
+			st,syscon = <&syscfg 0x4>;
+			snps,pbl = <8>;
+			snps,mixed-burst;
+			dma-ranges;
+			status = "disabled";
+		};
+
+		usbotg_hs: usb@40040000 {
+			compatible = "snps,dwc2";
+			dma-ranges;
+			reg = <0x40040000 0x40000>;
+			interrupts = <77>;
+			clocks = <&rcc 0 29>;
+			clock-names = "otg";
+			status = "disabled";
+		};
+
 		rng: rng@50060800 {
 			compatible = "st,stm32-rng";
 			reg = <0x50060800 0x400>;

arch/arm/boot/dts/stm32f469-disco.dts

+/*
+ * Copyright 2016 - Lee Jones <lee.jones@linaro.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "stm32f429.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32F469i-DISCO board";
+	compatible = "st,stm32f469i-disco", "st,stm32f469";
+
+	chosen {
+		bootargs = "root=/dev/ram rdinit=/linuxrc";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0x00000000 0x800000>;
+	};
+
+	aliases {
+		serial0 = &usart3;
+	};
+};
+
+&clk_hse {
+	clock-frequency = <8000000>;
+};
+
+&usart3 {
+	status = "okay";
+};