docs: networking: device drivers: convert neterion/vxge.txt to ReST

- add SPDX header;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/networking/device_drivers/index.rst

@@ -43,6 +43,7 @@ Contents:
    intel/ipw2200
    microsoft/netvsc
    neterion/s2io
+   neterion/vxge
 
 .. only::  subproject and html
 

Documentation/networking/device_drivers/neterion/vxge.txt → Documentation/networking/device_drivers/neterion/vxge.rst

+.. SPDX-License-Identifier: GPL-2.0
+
+==============================================================================
 Neterion's (Formerly S2io) X3100 Series 10GbE PCIe Server Adapter Linux driver
 ==============================================================================
 
-Contents
---------
+.. Contents
+
+  1) Introduction
+  2) Features supported
+  3) Configurable driver parameters
+  4) Troubleshooting
 
-1) Introduction
-2) Features supported
-3) Configurable driver parameters
-4) Troubleshooting
+1. Introduction
+===============
 
-1) Introduction:
-----------------
 This Linux driver supports all Neterion's X3100 series 10 GbE PCIe I/O
 Virtualized Server adapters.
+
 The X3100 series supports four modes of operation, configurable via
-firmware -
-	Single function mode
-	Multi function mode
-	SRIOV mode
-	MRIOV mode
+firmware:
+
+	- Single function mode
+	- Multi function mode
+	- SRIOV mode
+	- MRIOV mode
+
 The functions share a 10GbE link and the pci-e bus, but hardly anything else
 inside the ASIC. Features like independent hw reset, statistics, bandwidth/
 priority allocation and guarantees, GRO, TSO, interrupt moderation etc are
@@ -26,41 +32,49 @@ supported independently on each function.
 
 (See below for a complete list of features supported for both IPv4 and IPv6)
 
-2) Features supported:
-----------------------
+2. Features supported
+=====================
 
 i)   Single function mode (up to 17 queues)
 
 ii)  Multi function mode (up to 17 functions)
 
 iii) PCI-SIG's I/O Virtualization
+
        - Single Root mode: v1.0 (up to 17 functions)
        - Multi-Root mode: v1.0 (up to 17 functions)
 
 iv)  Jumbo frames
+
        X3100 Series supports MTU up to 9600 bytes, modifiable using
        ip command.
 
 v)   Offloads supported: (Enabled by default)
-       Checksum offload (TCP/UDP/IP) on transmit and receive paths
-       TCP Segmentation Offload (TSO) on transmit path
-       Generic Receive Offload (GRO) on receive path
+
+       - Checksum offload (TCP/UDP/IP) on transmit and receive paths
+       - TCP Segmentation Offload (TSO) on transmit path
+       - Generic Receive Offload (GRO) on receive path
 
 vi)  MSI-X: (Enabled by default)
+
        Resulting in noticeable performance improvement (up to 7% on certain
        platforms).
 
 vii) NAPI: (Enabled by default)
+
        For better Rx interrupt moderation.
 
 viii)RTH (Receive Traffic Hash): (Enabled by default)
+
        Receive side steering for better scaling.
 
 ix)  Statistics
+
        Comprehensive MAC-level and software statistics displayed using
        "ethtool -S" option.
 
 x)   Multiple hardware queues: (Enabled by default)
+
        Up to 17 hardware based transmit and receive data channels, with
        multiple steering options (transmit multiqueue enabled by default).
 
@@ -69,25 +83,33 @@ x)   Multiple hardware queues: (Enabled by default)
 
 i)  max_config_dev
        Specifies maximum device functions to be enabled.
+
        Valid range: 1-8
 
 ii) max_config_port
        Specifies number of ports to be enabled.
+
        Valid range: 1,2
+
        Default: 1
 
-iii)max_config_vpath
+iii) max_config_vpath
        Specifies maximum VPATH(s) configured for each device function.
+
        Valid range: 1-17
 
 iv) vlan_tag_strip
        Enables/disables vlan tag stripping from all received tagged frames that
        are not replicated at the internal L2 switch.
+
        Valid range: 0,1 (disabled, enabled respectively)
+
        Default: 1
 
 v)  addr_learn_en
        Enable learning the mac address of the guest OS interface in
        virtualization environment.
+
        Valid range: 0,1 (disabled, enabled respectively)
+
        Default: 0

MAINTAINERS

@@ -11657,7 +11657,7 @@ M:	Jon Mason <jdmason@kudzu.us>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	Documentation/networking/device_drivers/neterion/s2io.rst
-F:	Documentation/networking/device_drivers/neterion/vxge.txt
+F:	Documentation/networking/device_drivers/neterion/vxge.rst
 F:	drivers/net/ethernet/neterion/
 
 NETFILTER

drivers/net/ethernet/neterion/Kconfig

@@ -42,7 +42,7 @@ config VXGE
 	  labeled as either one, depending on its age.
 
 	  More specific information on configuring the driver is in
-	  <file:Documentation/networking/device_drivers/neterion/vxge.txt>.
+	  <file:Documentation/networking/device_drivers/neterion/vxge.rst>.
 
 	  To compile this driver as a module, choose M here. The module
 	  will be called vxge.