drm/msm/dp: Drop now unused hpd_high member

Since '8ede2ecc ("drm/msm/dp: Add DP compliance tests on Snapdragon
Chipsets")' the hpd_high member of struct dp_usbpd has been write-only.

Let's clean up the code a little bit by removing the writes as well.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211106172246.2597431-1-bjorn.andersson@linaro.orgSigned-off-by: Rob Clark <robdclark@chromium.org>

drivers/gpu/drm/msm/dp/dp_display.c

@@ -531,11 +531,8 @@ static int dp_hpd_plug_handle(struct dp_display_private *dp, u32 data)
 
 	dp->hpd_state = ST_CONNECT_PENDING;
 
-	hpd->hpd_high = 1;
-
 	ret = dp_display_usbpd_configure_cb(&dp->pdev->dev);
 	if (ret) {	/* link train failed */
-		hpd->hpd_high = 0;
 		dp->hpd_state = ST_DISCONNECTED;
 
 		if (ret == -ECONNRESET) { /* cable unplugged */
@@ -612,7 +609,6 @@ static int dp_hpd_unplug_handle(struct dp_display_private *dp, u32 data)
 		/* triggered by irq_hdp with sink_count = 0 */
 		if (dp->link->sink_count == 0) {
 			dp_ctrl_off_phy(dp->ctrl);
-			hpd->hpd_high = 0;
 			dp->core_initialized = false;
 		}
 		mutex_unlock(&dp->event_mutex);
@@ -636,8 +632,6 @@ static int dp_hpd_unplug_handle(struct dp_display_private *dp, u32 data)
 	/* disable HPD plug interrupts */
 	dp_catalog_hpd_config_intr(dp->catalog, DP_DP_HPD_PLUG_INT_MASK, false);
 
-	hpd->hpd_high = 0;
-
 	/*
 	 * We don't need separate work for disconnect as
 	 * connect/attention interrupts are disabled

drivers/gpu/drm/msm/dp/dp_hpd.c

@@ -32,8 +32,6 @@ int dp_hpd_connect(struct dp_usbpd *dp_usbpd, bool hpd)
 	hpd_priv = container_of(dp_usbpd, struct dp_hpd_private,
 					dp_usbpd);
 
-	dp_usbpd->hpd_high = hpd;
-
 	if (!hpd_priv->dp_cb || !hpd_priv->dp_cb->configure
 				|| !hpd_priv->dp_cb->disconnect) {
 		pr_err("hpd dp_cb not initialized\n");

drivers/gpu/drm/msm/dp/dp_hpd.h

@@ -26,7 +26,6 @@ enum plug_orientation {
  * @multi_func: multi-function preferred
  * @usb_config_req: request to switch to usb
  * @exit_dp_mode: request exit from displayport mode
- * @hpd_high: Hot Plug Detect signal is high.
  * @hpd_irq: Change in the status since last message
  * @alt_mode_cfg_done: bool to specify alt mode status
  * @debug_en: bool to specify debug mode
@@ -39,7 +38,6 @@ struct dp_usbpd {
 	bool multi_func;
 	bool usb_config_req;
 	bool exit_dp_mode;
-	bool hpd_high;
 	bool hpd_irq;
 	bool alt_mode_cfg_done;
 	bool debug_en;