Skip to content

L
linux
Commit fb7a6d4e authored by David S. Miller's avatar David S. Miller
Browse files
Options

Merge git://github.com/Jkirsher/net-next

parents 230dec61 8c838d73
Show whitespace changes
Inline Side-by-side
Showing with 443 additions and 245 deletions
drivers/net/ethernet/intel/ixgbe/ixgbe.h
View file @ fb7a6d4e
......@@ -128,6 +128,7 @@ struct vf_data_storage {
u16 pf_vlan; /* When set, guest VLAN config not allowed. */
u16 pf_qos;
u16 tx_rate;
struct pci_dev *vfdev;
};
struct vf_macvlans {
......@@ -490,6 +491,7 @@ struct ixgbe_adapter {
u64 rsc_total_flush;
u32 wol;
u16 eeprom_version;
u16 eeprom_cap;
int node;
u32 led_reg;
......
drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c
View file @ fb7a6d4e
......@@ -759,7 +759,9 @@ static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw)
u8 analog_val;
/* Call adapter stop to disable tx/rx and clear interrupts */
hw->mac.ops.stop_adapter(hw);
status = hw->mac.ops.stop_adapter(hw);
if (status != 0)
goto reset_hw_out;
/*
* Power up the Atlas Tx lanes if they are currently powered down.
......@@ -802,19 +804,12 @@ static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw)
phy_status = hw->phy.ops.init(hw);
if (phy_status == IXGBE_ERR_SFP_NOT_SUPPORTED)
goto reset_hw_out;
else if (phy_status == IXGBE_ERR_SFP_NOT_PRESENT)
goto no_phy_reset;
if (phy_status == IXGBE_ERR_SFP_NOT_PRESENT)
goto mac_reset_top;
hw->phy.ops.reset(hw);
}
no_phy_reset:
/*
* Prevent the PCI-E bus from from hanging by disabling PCI-E master
* access and verify no pending requests before reset
*/
ixgbe_disable_pcie_master(hw);
mac_reset_top:
/*
* Issue global reset to the MAC. This needs to be a SW reset.
......
drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
View file @ fb7a6d4e
......@@ -910,7 +910,12 @@ static s32 ixgbe_reset_hw_82599(struct ixgbe_hw *hw)
bool link_up = false;
/* Call adapter stop to disable tx/rx and clear interrupts */
hw->mac.ops.stop_adapter(hw);
status = hw->mac.ops.stop_adapter(hw);
if (status != 0)
goto reset_hw_out;
/* flush pending Tx transactions */
ixgbe_clear_tx_pending(hw);
/* PHY ops must be identified and initialized prior to reset */
......@@ -933,12 +938,6 @@ static s32 ixgbe_reset_hw_82599(struct ixgbe_hw *hw)
if (hw->phy.reset_disable == false && hw->phy.ops.reset != NULL)
hw->phy.ops.reset(hw);
/*
* Prevent the PCI-E bus from from hanging by disabling PCI-E master
* access and verify no pending requests before reset
*/
ixgbe_disable_pcie_master(hw);
mac_reset_top:
/*
* Issue global reset to the MAC. Needs to be SW reset if link is up.
......
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
View file @ fb7a6d4e
......@@ -61,6 +61,7 @@ static s32 ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
u16 words, u16 *data);
static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw,
u16 offset);
static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw);
/**
* ixgbe_start_hw_generic - Prepare hardware for Tx/Rx
......@@ -496,7 +497,6 @@ void ixgbe_set_lan_id_multi_port_pcie(struct ixgbe_hw *hw)
**/
s32 ixgbe_stop_adapter_generic(struct ixgbe_hw *hw)
{
u32 number_of_queues;
u32 reg_val;
u16 i;
......@@ -507,35 +507,35 @@ s32 ixgbe_stop_adapter_generic(struct ixgbe_hw *hw)
hw->adapter_stopped = true;
/* Disable the receive unit */
reg_val = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
reg_val &= ~(IXGBE_RXCTRL_RXEN);
IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, reg_val);
IXGBE_WRITE_FLUSH(hw);
usleep_range(2000, 4000);
IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, 0);
/* Clear interrupt mask to stop from interrupts being generated */
/* Clear interrupt mask to stop interrupts from being generated */
IXGBE_WRITE_REG(hw, IXGBE_EIMC, IXGBE_IRQ_CLEAR_MASK);
/* Clear any pending interrupts */
/* Clear any pending interrupts, flush previous writes */
IXGBE_READ_REG(hw, IXGBE_EICR);
/* Disable the transmit unit. Each queue must be disabled. */
number_of_queues = hw->mac.max_tx_queues;
for (i = 0; i < number_of_queues; i++) {
reg_val = IXGBE_READ_REG(hw, IXGBE_TXDCTL(i));
if (reg_val & IXGBE_TXDCTL_ENABLE) {
reg_val &= ~IXGBE_TXDCTL_ENABLE;
IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(i), reg_val);
}
for (i = 0; i < hw->mac.max_tx_queues; i++)
IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(i), IXGBE_TXDCTL_SWFLSH);
/* Disable the receive unit by stopping each queue */
for (i = 0; i < hw->mac.max_rx_queues; i++) {
reg_val = IXGBE_READ_REG(hw, IXGBE_RXDCTL(i));
reg_val &= ~IXGBE_RXDCTL_ENABLE;
reg_val |= IXGBE_RXDCTL_SWFLSH;
IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(i), reg_val);
}
/* flush all queues disables */
IXGBE_WRITE_FLUSH(hw);
usleep_range(1000, 2000);
/*
* Prevent the PCI-E bus from from hanging by disabling PCI-E master
* access and verify no pending requests
*/
ixgbe_disable_pcie_master(hw);
return 0;
return ixgbe_disable_pcie_master(hw);
}
/**
......@@ -2458,75 +2458,57 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
* bit hasn't caused the master requests to be disabled, else 0
* is returned signifying master requests disabled.
**/
s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw)
static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw)
{
struct ixgbe_adapter *adapter = hw->back;
u32 i;
u32 reg_val;
u32 number_of_queues;
s32 status = 0;
u16 dev_status = 0;
u32 i;
u16 value;
/* Just jump out if bus mastering is already disabled */
/* Always set this bit to ensure any future transactions are blocked */
IXGBE_WRITE_REG(hw, IXGBE_CTRL, IXGBE_CTRL_GIO_DIS);
/* Exit if master requests are blocked */
if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO))
goto out;
/* Disable the receive unit by stopping each queue */
number_of_queues = hw->mac.max_rx_queues;
for (i = 0; i < number_of_queues; i++) {
reg_val = IXGBE_READ_REG(hw, IXGBE_RXDCTL(i));
if (reg_val & IXGBE_RXDCTL_ENABLE) {
reg_val &= ~IXGBE_RXDCTL_ENABLE;
IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(i), reg_val);
}
}
reg_val = IXGBE_READ_REG(hw, IXGBE_CTRL);
reg_val |= IXGBE_CTRL_GIO_DIS;
IXGBE_WRITE_REG(hw, IXGBE_CTRL, reg_val);
/* Poll for master request bit to clear */
for (i = 0; i < IXGBE_PCI_MASTER_DISABLE_TIMEOUT; i++) {
if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO))
goto check_device_status;
udelay(100);
if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO))
goto out;
}
/*
* Two consecutive resets are required via CTRL.RST per datasheet
* 5.2.5.3.2 Master Disable. We set a flag to inform the reset routine
* of this need. The first reset prevents new master requests from
* being issued by our device. We then must wait 1usec or more for any
* remaining completions from the PCIe bus to trickle in, and then reset
* again to clear out any effects they may have had on our device.
*/
hw_dbg(hw, "GIO Master Disable bit didn't clear - requesting resets\n");
status = IXGBE_ERR_MASTER_REQUESTS_PENDING;
hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
/*
* Before proceeding, make sure that the PCIe block does not have
* transactions pending.
*/
check_device_status:
for (i = 0; i < IXGBE_PCI_MASTER_DISABLE_TIMEOUT; i++) {
pci_read_config_word(adapter->pdev, IXGBE_PCI_DEVICE_STATUS,
&dev_status);
if (!(dev_status & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING))
break;
udelay(100);
pci_read_config_word(adapter->pdev, IXGBE_PCI_DEVICE_STATUS,
&value);
if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING))
goto out;
}
if (i == IXGBE_PCI_MASTER_DISABLE_TIMEOUT)
hw_dbg(hw, "PCIe transaction pending bit also did not clear.\n");
else
goto out;
/*
* Two consecutive resets are required via CTRL.RST per datasheet
* 5.2.5.3.2 Master Disable. We set a flag to inform the reset routine
* of this need. The first reset prevents new master requests from
* being issued by our device. We then must wait 1usec for any
* remaining completions from the PCIe bus to trickle in, and then reset
* again to clear out any effects they may have had on our device.
*/
hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
status = IXGBE_ERR_MASTER_REQUESTS_PENDING;
out:
return status;
}
/**
* ixgbe_acquire_swfw_sync - Acquire SWFW semaphore
* @hw: pointer to hardware structure
......@@ -3509,3 +3491,44 @@ s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min,
out:
return ret_val;
}
/**
* ixgbe_clear_tx_pending - Clear pending TX work from the PCIe fifo
* @hw: pointer to the hardware structure
*
* The 82599 and x540 MACs can experience issues if TX work is still pending
* when a reset occurs. This function prevents this by flushing the PCIe
* buffers on the system.
**/
void ixgbe_clear_tx_pending(struct ixgbe_hw *hw)
{
u32 gcr_ext, hlreg0;
/*
* If double reset is not requested then all transactions should
* already be clear and as such there is no work to do
*/
if (!(hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED))
return;
/*
* Set loopback enable to prevent any transmits from being sent
* should the link come up. This assumes that the RXCTRL.RXEN bit
* has already been cleared.
*/
hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0);
IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0 | IXGBE_HLREG0_LPBK);
/* initiate cleaning flow for buffers in the PCIe transaction layer */
gcr_ext = IXGBE_READ_REG(hw, IXGBE_GCR_EXT);
IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT,
gcr_ext | IXGBE_GCR_EXT_BUFFERS_CLEAR);
/* Flush all writes and allow 20usec for all transactions to clear */
IXGBE_WRITE_FLUSH(hw);
udelay(20);
/* restore previous register values */
IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, gcr_ext);
IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0);
}
drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
View file @ fb7a6d4e
......@@ -81,7 +81,6 @@ s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw);
s32 ixgbe_validate_mac_addr(u8 *mac_addr);
s32 ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u16 mask);
void ixgbe_release_swfw_sync(struct ixgbe_hw *hw, u16 mask);
s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw);
s32 ixgbe_get_san_mac_addr_generic(struct ixgbe_hw *hw, u8 *san_mac_addr);
s32 ixgbe_set_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq);
s32 ixgbe_clear_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq);
......@@ -101,6 +100,7 @@ void ixgbe_set_vlan_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf);
s32 ixgbe_get_device_caps_generic(struct ixgbe_hw *hw, u16 *device_caps);
s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min,
u8 build, u8 ver);
void ixgbe_clear_tx_pending(struct ixgbe_hw *hw);
void ixgbe_set_rxpba_generic(struct ixgbe_hw *hw, int num_pb,
u32 headroom, int strategy);
......
drivers/net/ethernet/intel/ixgbe/ixgbe_dcb.c
View file @ fb7a6d4e
......@@ -40,7 +40,8 @@
* hardware. The IEEE 802.1Qaz specification do not use bandwidth
* groups so this is much simplified from the CEE case.
*/
s32 ixgbe_ieee_credits(__u8 *bw, __u16 *refill, __u16 *max, int max_frame)
static s32 ixgbe_ieee_credits(__u8 *bw, __u16 *refill,
__u16 *max, int max_frame)
{
int min_percent = 100;
int min_credit, multiplier;
......@@ -291,6 +292,39 @@ s32 ixgbe_dcb_hw_pfc_config(struct ixgbe_hw *hw, u8 pfc_en)
return ret;
}
s32 ixgbe_dcb_hw_ets(struct ixgbe_hw *hw, struct ieee_ets *ets, int max_frame)
{
__u16 refill[IEEE_8021QAZ_MAX_TCS], max[IEEE_8021QAZ_MAX_TCS];
__u8 prio_type[IEEE_8021QAZ_MAX_TCS];
int i;
/* naively give each TC a bwg to map onto CEE hardware */
__u8 bwg_id[IEEE_8021QAZ_MAX_TCS] = {0, 1, 2, 3, 4, 5, 6, 7};
/* Map TSA onto CEE prio type */
for (i = 0; i < IEEE_8021QAZ_MAX_TCS; i++) {
switch (ets->tc_tsa[i]) {
case IEEE_8021QAZ_TSA_STRICT:
prio_type[i] = 2;
break;
case IEEE_8021QAZ_TSA_ETS:
prio_type[i] = 0;
break;
default:
/* Hardware only supports priority strict or
* ETS transmission selection algorithms if
* we receive some other value from dcbnl
* throw an error
*/
return -EINVAL;
}
}
ixgbe_ieee_credits(ets->tc_tx_bw, refill, max, max_frame);
return ixgbe_dcb_hw_ets_config(hw, refill, max,
bwg_id, prio_type, ets->prio_tc);
}
s32 ixgbe_dcb_hw_ets_config(struct ixgbe_hw *hw,
u16 *refill, u16 *max, u8 *bwg_id,
u8 *prio_type, u8 *prio_tc)
......
drivers/net/ethernet/intel/ixgbe/ixgbe_dcb.h
View file @ fb7a6d4e
......@@ -29,6 +29,7 @@
#ifndef _DCB_CONFIG_H_
#define _DCB_CONFIG_H_
#include <linux/dcbnl.h>
#include "ixgbe_type.h"
/* DCB data structures */
......@@ -147,11 +148,11 @@ void ixgbe_dcb_unpack_bwgid(struct ixgbe_dcb_config *, int, u8 *);
void ixgbe_dcb_unpack_prio(struct ixgbe_dcb_config *, int, u8 *);
/* DCB credits calculation */
s32 ixgbe_ieee_credits(__u8 *bw, __u16 *refill, __u16 *max, int max_frame);
s32 ixgbe_dcb_calculate_tc_credits(struct ixgbe_hw *,
struct ixgbe_dcb_config *, int, u8);
/* DCB hw initialization */
s32 ixgbe_dcb_hw_ets(struct ixgbe_hw *hw, struct ieee_ets *ets, int max);
s32 ixgbe_dcb_hw_ets_config(struct ixgbe_hw *hw, u16 *refill, u16 *max,
u8 *bwg_id, u8 *prio_type, u8 *tc_prio);
s32 ixgbe_dcb_hw_pfc_config(struct ixgbe_hw *hw, u8 pfc_en);
......
drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_nl.c
View file @ fb7a6d4e
......@@ -114,6 +114,10 @@ static u8 ixgbe_dcbnl_set_state(struct net_device *netdev, u8 state)
u8 err = 0;
struct ixgbe_adapter *adapter = netdev_priv(netdev);
/* Fail command if not in CEE mode */
if (!(adapter->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
return 1;
/* verify there is something to do, if not then exit */
if (!!state != !(adapter->flags & IXGBE_FLAG_DCB_ENABLED))
return err;
......@@ -301,6 +305,10 @@ static u8 ixgbe_dcbnl_set_all(struct net_device *netdev)
u8 up = dcb_getapp(netdev, &app);
#endif
/* Fail command if not in CEE mode */
if (!(adapter->dcbx_cap & DCB_CAP_DCBX_VER_CEE))
return 1;
ret = ixgbe_copy_dcb_cfg(&adapter->temp_dcb_cfg, &adapter->dcb_cfg,
MAX_TRAFFIC_CLASS);
if (ret)
......@@ -537,13 +545,9 @@ static int ixgbe_dcbnl_ieee_setets(struct net_device *dev,
struct ieee_ets *ets)
{
struct ixgbe_adapter *adapter = netdev_priv(dev);
__u16 refill[IEEE_8021QAZ_MAX_TCS], max[IEEE_8021QAZ_MAX_TCS];
__u8 prio_type[IEEE_8021QAZ_MAX_TCS];
int max_frame = dev->mtu + ETH_HLEN + ETH_FCS_LEN;
int i, err;
__u64 *p = (__u64 *) ets->prio_tc;
/* naively give each TC a bwg to map onto CEE hardware */
__u8 bwg_id[IEEE_8021QAZ_MAX_TCS] = {0, 1, 2, 3, 4, 5, 6, 7};
int i;
__u8 max_tc = 0;
if (!(adapter->dcbx_cap & DCB_CAP_DCBX_VER_IEEE))
return -EINVAL;
......@@ -557,34 +561,21 @@ static int ixgbe_dcbnl_ieee_setets(struct net_device *dev,
memcpy(adapter->ixgbe_ieee_ets, ets, sizeof(*adapter->ixgbe_ieee_ets));
/* Map TSA onto CEE prio type */
for (i = 0; i < IEEE_8021QAZ_MAX_TCS; i++) {
switch (ets->tc_tsa[i]) {
case IEEE_8021QAZ_TSA_STRICT:
prio_type[i] = 2;
break;
case IEEE_8021QAZ_TSA_ETS:
prio_type[i] = 0;
break;
default:
/* Hardware only supports priority strict or
* ETS transmission selection algorithms if
* we receive some other value from dcbnl
* throw an error
*/
return -EINVAL;
}
if (ets->prio_tc[i] > max_tc)
max_tc = ets->prio_tc[i];
}
if (*p)
ixgbe_dcbnl_set_state(dev, 1);
else
ixgbe_dcbnl_set_state(dev, 0);
if (max_tc)
max_tc++;
ixgbe_ieee_credits(ets->tc_tx_bw, refill, max, max_frame);
err = ixgbe_dcb_hw_ets_config(&adapter->hw, refill, max,
bwg_id, prio_type, ets->prio_tc);
return err;
if (max_tc != netdev_get_num_tc(dev))
ixgbe_setup_tc(dev, max_tc);
for (i = 0; i < IEEE_8021QAZ_MAX_TCS; i++)
netdev_set_prio_tc_map(dev, i, ets->prio_tc[i]);
return ixgbe_dcb_hw_ets(&adapter->hw, ets, max_frame);
}
static int ixgbe_dcbnl_ieee_getpfc(struct net_device *dev,
......@@ -615,7 +606,6 @@ static int ixgbe_dcbnl_ieee_setpfc(struct net_device *dev,
struct ieee_pfc *pfc)
{
struct ixgbe_adapter *adapter = netdev_priv(dev);
int err;
if (!(adapter->dcbx_cap & DCB_CAP_DCBX_VER_IEEE))
return -EINVAL;
......@@ -628,8 +618,7 @@ static int ixgbe_dcbnl_ieee_setpfc(struct net_device *dev,
}
memcpy(adapter->ixgbe_ieee_pfc, pfc, sizeof(*adapter->ixgbe_ieee_pfc));
err = ixgbe_dcb_hw_pfc_config(&adapter->hw, pfc->pfc_en);
return err;
return ixgbe_dcb_hw_pfc_config(&adapter->hw, pfc->pfc_en);
}
#ifdef IXGBE_FCOE
......@@ -740,7 +729,7 @@ static u8 ixgbe_dcbnl_setdcbx(struct net_device *dev, u8 mode)
*/
ixgbe_dcbnl_ieee_setets(dev, &ets);
ixgbe_dcbnl_ieee_setpfc(dev, &pfc);
ixgbe_dcbnl_set_state(dev, 0);
ixgbe_setup_tc(dev, 0);
}
return 0;
......
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
View file @ fb7a6d4e
......@@ -1888,6 +1888,7 @@ static int ixgbe_wol_exclusion(struct ixgbe_adapter *adapter,
{
struct ixgbe_hw *hw = &adapter->hw;
int retval = 1;
u16 wol_cap = adapter->eeprom_cap & IXGBE_DEVICE_CAPS_WOL_MASK;
/* WOL not supported except for the following */
switch(hw->device_id) {
......@@ -1911,6 +1912,18 @@ static int ixgbe_wol_exclusion(struct ixgbe_adapter *adapter,
case IXGBE_DEV_ID_82599_KX4:
retval = 0;
break;
case IXGBE_DEV_ID_X540T:
/* check eeprom to see if enabled wol */
if ((wol_cap == IXGBE_DEVICE_CAPS_WOL_PORT0_1) ||
((wol_cap == IXGBE_DEVICE_CAPS_WOL_PORT0) &&
(hw->bus.func == 0))) {
retval = 0;
break;
}
/* All others not supported */
wol->supported = 0;
break;
default:
wol->supported = 0;
}
......
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
View file @ fb7a6d4e
......@@ -134,42 +134,6 @@ MODULE_VERSION(DRV_VERSION);
#define DEFAULT_DEBUG_LEVEL_SHIFT 3
static inline void ixgbe_disable_sriov(struct ixgbe_adapter *adapter)
{
struct ixgbe_hw *hw = &adapter->hw;
u32 gcr;
u32 gpie;
u32 vmdctl;
#ifdef CONFIG_PCI_IOV
/* disable iov and allow time for transactions to clear */
pci_disable_sriov(adapter->pdev);
#endif
/* turn off device IOV mode */
gcr = IXGBE_READ_REG(hw, IXGBE_GCR_EXT);
gcr &= ~(IXGBE_GCR_EXT_SRIOV);
IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, gcr);
gpie = IXGBE_READ_REG(hw, IXGBE_GPIE);
gpie &= ~IXGBE_GPIE_VTMODE_MASK;
IXGBE_WRITE_REG(hw, IXGBE_GPIE, gpie);
/* set default pool back to 0 */
vmdctl = IXGBE_READ_REG(hw, IXGBE_VT_CTL);
vmdctl &= ~IXGBE_VT_CTL_POOL_MASK;
IXGBE_WRITE_REG(hw, IXGBE_VT_CTL, vmdctl);
IXGBE_WRITE_FLUSH(hw);
/* take a breather then clean up driver data */
msleep(100);
kfree(adapter->vfinfo);
adapter->vfinfo = NULL;
adapter->num_vfs = 0;
adapter->flags &= ~IXGBE_FLAG_SRIOV_ENABLED;
}
static void ixgbe_service_event_schedule(struct ixgbe_adapter *adapter)
{
if (!test_bit(__IXGBE_DOWN, &adapter->state) &&
......@@ -1899,10 +1863,10 @@ static inline void ixgbe_irq_enable(struct ixgbe_adapter *adapter, bool queues,
mask |= IXGBE_EIMS_GPI_SDP1;
switch (adapter->hw.mac.type) {
case ixgbe_mac_82599EB:
case ixgbe_mac_X540:
mask |= IXGBE_EIMS_ECC;
mask |= IXGBE_EIMS_GPI_SDP1;
mask |= IXGBE_EIMS_GPI_SDP2;
case ixgbe_mac_X540:
mask |= IXGBE_EIMS_ECC;
mask |= IXGBE_EIMS_MAILBOX;
break;
default:
......@@ -3355,12 +3319,18 @@ static void ixgbe_configure_dcb(struct ixgbe_adapter *adapter)
} else {
struct net_device *dev = adapter->netdev;
if (adapter->ixgbe_ieee_ets)
dev->dcbnl_ops->ieee_setets(dev,
adapter->ixgbe_ieee_ets);
if (adapter->ixgbe_ieee_pfc)
dev->dcbnl_ops->ieee_setpfc(dev,
adapter->ixgbe_ieee_pfc);
if (adapter->ixgbe_ieee_ets) {
struct ieee_ets *ets = adapter->ixgbe_ieee_ets;
int max_frame = dev->mtu + ETH_HLEN + ETH_FCS_LEN;
ixgbe_dcb_hw_ets(&adapter->hw, ets, max_frame);
}
if (adapter->ixgbe_ieee_pfc) {
struct ieee_pfc *pfc = adapter->ixgbe_ieee_pfc;
ixgbe_dcb_hw_pfc_config(&adapter->hw, pfc->pfc_en);
}
}
/* Enable RSS Hash per TC */
......@@ -7064,11 +7034,8 @@ static void __devinit ixgbe_probe_vf(struct ixgbe_adapter *adapter,
{
#ifdef CONFIG_PCI_IOV
struct ixgbe_hw *hw = &adapter->hw;
int err;
int num_vf_macvlans, i;
struct vf_macvlans *mv_list;
if (hw->mac.type == ixgbe_mac_82598EB || !max_vfs)
if (hw->mac.type == ixgbe_mac_82598EB)
return;
/* The 82599 supports up to 64 VFs per physical function
......@@ -7077,60 +7044,7 @@ static void __devinit ixgbe_probe_vf(struct ixgbe_adapter *adapter,
* physical function
*/
adapter->num_vfs = (max_vfs > 63) ? 63 : max_vfs;
adapter->flags |= IXGBE_FLAG_SRIOV_ENABLED;
err = pci_enable_sriov(adapter->pdev, adapter->num_vfs);
if (err) {
e_err(probe, "Failed to enable PCI sriov: %d\n", err);
goto err_novfs;
}
num_vf_macvlans = hw->mac.num_rar_entries -
(IXGBE_MAX_PF_MACVLANS + 1 + adapter->num_vfs);
adapter->mv_list = mv_list = kcalloc(num_vf_macvlans,
sizeof(struct vf_macvlans),
GFP_KERNEL);
if (mv_list) {
/* Initialize list of VF macvlans */
INIT_LIST_HEAD(&adapter->vf_mvs.l);
for (i = 0; i < num_vf_macvlans; i++) {
mv_list->vf = -1;
mv_list->free = true;
mv_list->rar_entry = hw->mac.num_rar_entries -
(i + adapter->num_vfs + 1);
list_add(&mv_list->l, &adapter->vf_mvs.l);
mv_list++;
}
}
/* If call to enable VFs succeeded then allocate memory
* for per VF control structures.
*/
adapter->vfinfo =
kcalloc(adapter->num_vfs,
sizeof(struct vf_data_storage), GFP_KERNEL);
if (adapter->vfinfo) {
/* Now that we're sure SR-IOV is enabled
* and memory allocated set up the mailbox parameters
*/
ixgbe_init_mbx_params_pf(hw);
memcpy(&hw->mbx.ops, ii->mbx_ops,
sizeof(hw->mbx.ops));
/* Disable RSC when in SR-IOV mode */
adapter->flags2 &= ~(IXGBE_FLAG2_RSC_CAPABLE |
IXGBE_FLAG2_RSC_ENABLED);
return;
}
/* Oh oh */
e_err(probe, "Unable to allocate memory for VF Data Storage - "
"SRIOV disabled\n");
pci_disable_sriov(adapter->pdev);
err_novfs:
adapter->flags &= ~IXGBE_FLAG_SRIOV_ENABLED;
adapter->num_vfs = 0;
ixgbe_enable_sriov(adapter, ii);
#endif /* CONFIG_PCI_IOV */
}
......@@ -7160,6 +7074,7 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
u16 device_caps;
#endif
u32 eec;
u16 wol_cap;
/* Catch broken hardware that put the wrong VF device ID in
* the PCIe SR-IOV capability.
......@@ -7424,6 +7339,8 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
netdev->features &= ~NETIF_F_RXHASH;
}
/* WOL not supported for all but the following */
adapter->wol = 0;
switch (pdev->device) {
case IXGBE_DEV_ID_82599_SFP:
/* Only this subdevice supports WOL */
......@@ -7438,8 +7355,15 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
case IXGBE_DEV_ID_82599_KX4:
adapter->wol = IXGBE_WUFC_MAG;
break;
default:
adapter->wol = 0;
case IXGBE_DEV_ID_X540T:
/* Check eeprom to see if it is enabled */
hw->eeprom.ops.read(hw, 0x2c, &adapter->eeprom_cap);
wol_cap = adapter->eeprom_cap & IXGBE_DEVICE_CAPS_WOL_MASK;
if ((wol_cap == IXGBE_DEVICE_CAPS_WOL_PORT0_1) ||
((wol_cap == IXGBE_DEVICE_CAPS_WOL_PORT0) &&
(hw->bus.func == 0)))
adapter->wol = IXGBE_WUFC_MAG;
break;
}
device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
......@@ -7580,8 +7504,13 @@ static void __devexit ixgbe_remove(struct pci_dev *pdev)
if (netdev->reg_state == NETREG_REGISTERED)
unregister_netdev(netdev);
if (adapter->flags & IXGBE_FLAG_SRIOV_ENABLED)
if (adapter->flags & IXGBE_FLAG_SRIOV_ENABLED) {
if (!(ixgbe_check_vf_assignment(adapter)))
ixgbe_disable_sriov(adapter);
else
e_dev_warn("Unloading driver while VFs are assigned "
"- VFs will not be deallocated\n");
}
ixgbe_clear_interrupt_scheme(adapter);
......
drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c
View file @ fb7a6d4e
......@@ -40,9 +40,174 @@
#endif
#include "ixgbe.h"
#include "ixgbe_type.h"
#include "ixgbe_sriov.h"
#ifdef CONFIG_PCI_IOV
static int ixgbe_find_enabled_vfs(struct ixgbe_adapter *adapter)
{
struct pci_dev *pdev = adapter->pdev;
struct pci_dev *pvfdev;
u16 vf_devfn = 0;
int device_id;
int vfs_found = 0;
switch (adapter->hw.mac.type) {
case ixgbe_mac_82599EB:
device_id = IXGBE_DEV_ID_82599_VF;
break;
case ixgbe_mac_X540:
device_id = IXGBE_DEV_ID_X540_VF;
break;
default:
device_id = 0;
break;
}
vf_devfn = pdev->devfn + 0x80;
pvfdev = pci_get_device(IXGBE_INTEL_VENDOR_ID, device_id, NULL);
while (pvfdev) {
if (pvfdev->devfn == vf_devfn)
vfs_found++;
vf_devfn += 2;
pvfdev = pci_get_device(IXGBE_INTEL_VENDOR_ID,
device_id, pvfdev);
}
return vfs_found;
}
void ixgbe_enable_sriov(struct ixgbe_adapter *adapter,
const struct ixgbe_info *ii)
{
struct ixgbe_hw *hw = &adapter->hw;
int err = 0;
int num_vf_macvlans, i;
struct vf_macvlans *mv_list;
int pre_existing_vfs = 0;
pre_existing_vfs = ixgbe_find_enabled_vfs(adapter);
if (!pre_existing_vfs && !adapter->num_vfs)
return;
/* If there are pre-existing VFs then we have to force
* use of that many because they were not deleted the last
* time someone removed the PF driver. That would have
* been because they were allocated to guest VMs and can't
* be removed. Go ahead and just re-enable the old amount.
* If the user wants to change the number of VFs they can
* use ethtool while making sure no VFs are allocated to
* guest VMs... i.e. the right way.
*/
if (pre_existing_vfs) {
adapter->num_vfs = pre_existing_vfs;
dev_warn(&adapter->pdev->dev, "Virtual Functions already "
"enabled for this device - Please reload all "
"VF drivers to avoid spoofed packet errors\n");
} else {
err = pci_enable_sriov(adapter->pdev, adapter->num_vfs);
}
if (err) {
e_err(probe, "Failed to enable PCI sriov: %d\n", err);
goto err_novfs;
}
adapter->flags |= IXGBE_FLAG_SRIOV_ENABLED;
e_info(probe, "SR-IOV enabled with %d VFs\n", adapter->num_vfs);
num_vf_macvlans = hw->mac.num_rar_entries -
(IXGBE_MAX_PF_MACVLANS + 1 + adapter->num_vfs);
adapter->mv_list = mv_list = kcalloc(num_vf_macvlans,
sizeof(struct vf_macvlans),
GFP_KERNEL);
if (mv_list) {
/* Initialize list of VF macvlans */
INIT_LIST_HEAD(&adapter->vf_mvs.l);
for (i = 0; i < num_vf_macvlans; i++) {
mv_list->vf = -1;
mv_list->free = true;
mv_list->rar_entry = hw->mac.num_rar_entries -
(i + adapter->num_vfs + 1);
list_add(&mv_list->l, &adapter->vf_mvs.l);
mv_list++;
}
}
/* If call to enable VFs succeeded then allocate memory
* for per VF control structures.
*/
adapter->vfinfo =
kcalloc(adapter->num_vfs,
sizeof(struct vf_data_storage), GFP_KERNEL);
if (adapter->vfinfo) {
/* Now that we're sure SR-IOV is enabled
* and memory allocated set up the mailbox parameters
*/
ixgbe_init_mbx_params_pf(hw);
memcpy(&hw->mbx.ops, ii->mbx_ops,
sizeof(hw->mbx.ops));
/* Disable RSC when in SR-IOV mode */
adapter->flags2 &= ~(IXGBE_FLAG2_RSC_CAPABLE |
IXGBE_FLAG2_RSC_ENABLED);
return;
}
/* Oh oh */
e_err(probe, "Unable to allocate memory for VF Data Storage - "
"SRIOV disabled\n");
pci_disable_sriov(adapter->pdev);
err_novfs:
adapter->flags &= ~IXGBE_FLAG_SRIOV_ENABLED;
adapter->num_vfs = 0;
}
#endif /* #ifdef CONFIG_PCI_IOV */
void ixgbe_disable_sriov(struct ixgbe_adapter *adapter)
{
struct ixgbe_hw *hw = &adapter->hw;
u32 gcr;
u32 gpie;
u32 vmdctl;
int i;
#ifdef CONFIG_PCI_IOV
/* disable iov and allow time for transactions to clear */
pci_disable_sriov(adapter->pdev);
#endif
/* turn off device IOV mode */
gcr = IXGBE_READ_REG(hw, IXGBE_GCR_EXT);
gcr &= ~(IXGBE_GCR_EXT_SRIOV);
IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, gcr);
gpie = IXGBE_READ_REG(hw, IXGBE_GPIE);
gpie &= ~IXGBE_GPIE_VTMODE_MASK;
IXGBE_WRITE_REG(hw, IXGBE_GPIE, gpie);
/* set default pool back to 0 */
vmdctl = IXGBE_READ_REG(hw, IXGBE_VT_CTL);
vmdctl &= ~IXGBE_VT_CTL_POOL_MASK;
IXGBE_WRITE_REG(hw, IXGBE_VT_CTL, vmdctl);
IXGBE_WRITE_FLUSH(hw);
/* take a breather then clean up driver data */
msleep(100);
/* Release reference to VF devices */
for (i = 0; i < adapter->num_vfs; i++) {
if (adapter->vfinfo[i].vfdev)
pci_dev_put(adapter->vfinfo[i].vfdev);
}
kfree(adapter->vfinfo);
kfree(adapter->mv_list);
adapter->vfinfo = NULL;
adapter->num_vfs = 0;
adapter->flags &= ~IXGBE_FLAG_SRIOV_ENABLED;
}
static int ixgbe_set_vf_multicasts(struct ixgbe_adapter *adapter,
int entries, u16 *hash_list, u32 vf)
{
......@@ -273,11 +438,26 @@ static int ixgbe_set_vf_macvlan(struct ixgbe_adapter *adapter,
return 0;
}
int ixgbe_check_vf_assignment(struct ixgbe_adapter *adapter)
{
int i;
for (i = 0; i < adapter->num_vfs; i++) {
if (adapter->vfinfo[i].vfdev->dev_flags &
PCI_DEV_FLAGS_ASSIGNED)
return true;
}
return false;
}
int ixgbe_vf_configuration(struct pci_dev *pdev, unsigned int event_mask)
{
unsigned char vf_mac_addr[6];
struct ixgbe_adapter *adapter = pci_get_drvdata(pdev);
unsigned int vfn = (event_mask & 0x3f);
struct pci_dev *pvfdev;
unsigned int device_id;
u16 thisvf_devfn = (pdev->devfn + 0x80 + (vfn << 1)) |
(pdev->devfn & 1);
bool enable = ((event_mask & 0x10000000U) != 0);
......@@ -290,6 +470,31 @@ int ixgbe_vf_configuration(struct pci_dev *pdev, unsigned int event_mask)
* for it later.
*/
memcpy(adapter->vfinfo[vfn].vf_mac_addresses, vf_mac_addr, 6);
switch (adapter->hw.mac.type) {
case ixgbe_mac_82599EB:
device_id = IXGBE_DEV_ID_82599_VF;
break;
case ixgbe_mac_X540:
device_id = IXGBE_DEV_ID_X540_VF;
break;
default:
device_id = 0;
break;
}
pvfdev = pci_get_device(IXGBE_INTEL_VENDOR_ID, device_id, NULL);
while (pvfdev) {
if (pvfdev->devfn == thisvf_devfn)
break;
pvfdev = pci_get_device(IXGBE_INTEL_VENDOR_ID,
device_id, pvfdev);
}
if (pvfdev)
adapter->vfinfo[vfn].vfdev = pvfdev;
else
e_err(drv, "Couldn't find pci dev ptr for VF %4.4x\n",
thisvf_devfn);
}
return 0;
......
drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.h
View file @ fb7a6d4e
......@@ -41,6 +41,11 @@ int ixgbe_ndo_set_vf_bw(struct net_device *netdev, int vf, int tx_rate);
int ixgbe_ndo_get_vf_config(struct net_device *netdev,
int vf, struct ifla_vf_info *ivi);
void ixgbe_check_vf_rate_limit(struct ixgbe_adapter *adapter);
void ixgbe_disable_sriov(struct ixgbe_adapter *adapter);
void ixgbe_enable_sriov(struct ixgbe_adapter *adapter,
const struct ixgbe_info *ii);
int ixgbe_check_vf_assignment(struct ixgbe_adapter *adapter);
#endif /* _IXGBE_SRIOV_H_ */
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
View file @ fb7a6d4e
......@@ -65,6 +65,10 @@
#define IXGBE_DEV_ID_82599_LS 0x154F
#define IXGBE_DEV_ID_X540T 0x1528
/* VF Device IDs */
#define IXGBE_DEV_ID_82599_VF 0x10ED
#define IXGBE_DEV_ID_X540_VF 0x1515
/* General Registers */
#define IXGBE_CTRL 0x00000
#define IXGBE_STATUS 0x00008
......@@ -766,6 +770,7 @@
#define IXGBE_GCR_CAP_VER2 0x00040000
#define IXGBE_GCR_EXT_MSIX_EN 0x80000000
#define IXGBE_GCR_EXT_BUFFERS_CLEAR 0x40000000
#define IXGBE_GCR_EXT_VT_MODE_16 0x00000001
#define IXGBE_GCR_EXT_VT_MODE_32 0x00000002
#define IXGBE_GCR_EXT_VT_MODE_64 0x00000003
......@@ -1749,6 +1754,10 @@ enum {
#define IXGBE_ALT_SAN_MAC_ADDR_CAPS_SANMAC 0x0 /* Alt. SAN MAC exists */
#define IXGBE_ALT_SAN_MAC_ADDR_CAPS_ALTWWN 0x1 /* Alt. WWN base exists */
#define IXGBE_DEVICE_CAPS_WOL_PORT0_1 0x4 /* WoL supported on ports 0 & 1 */
#define IXGBE_DEVICE_CAPS_WOL_PORT0 0x8 /* WoL supported on port 0 */
#define IXGBE_DEVICE_CAPS_WOL_MASK 0xC /* Mask for WoL capabilities */
/* PCI Bus Info */
#define IXGBE_PCI_DEVICE_STATUS 0xAA
#define IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING 0x0020
......@@ -1818,6 +1827,7 @@ enum {
#define IXGBE_RXCTRL_RXEN 0x00000001 /* Enable Receiver */
#define IXGBE_RXCTRL_DMBYPS 0x00000002 /* Descriptor Monitor Bypass */
#define IXGBE_RXDCTL_ENABLE 0x02000000 /* Enable specific Rx Queue */
#define IXGBE_RXDCTL_SWFLSH 0x04000000 /* Rx Desc. write-back flushing */
#define IXGBE_RXDCTL_RLPMLMASK 0x00003FFF /* Only supported on the X540 */
#define IXGBE_RXDCTL_RLPML_EN 0x00008000
#define IXGBE_RXDCTL_VME 0x40000000 /* VLAN mode enable */
......
drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
View file @ fb7a6d4e
......@@ -93,34 +93,19 @@ static s32 ixgbe_setup_mac_link_X540(struct ixgbe_hw *hw,
**/
static s32 ixgbe_reset_hw_X540(struct ixgbe_hw *hw)
{
ixgbe_link_speed link_speed;
s32 status;
u32 ctrl, i;
bool link_up = false;
/* Call adapter stop to disable tx/rx and clear interrupts */
hw->mac.ops.stop_adapter(hw);
status = hw->mac.ops.stop_adapter(hw);
if (status != 0)
goto reset_hw_out;
/*
* Prevent the PCI-E bus from from hanging by disabling PCI-E master
* access and verify no pending requests before reset
*/
ixgbe_disable_pcie_master(hw);
/* flush pending Tx transactions */
ixgbe_clear_tx_pending(hw);
mac_reset_top:
/*
* Issue global reset to the MAC. Needs to be SW reset if link is up.
* If link reset is used when link is up, it might reset the PHY when
* mng is using it. If link is down or the flag to force full link
* reset is set, then perform link reset.
*/
ctrl = IXGBE_CTRL_LNK_RST;
if (!hw->force_full_reset) {
hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
if (link_up)
ctrl = IXGBE_CTRL_RST;
}
ctrl |= IXGBE_READ_REG(hw, IXGBE_CTRL);
IXGBE_WRITE_REG(hw, IXGBE_CTRL, ctrl);
IXGBE_WRITE_FLUSH(hw);
......@@ -137,8 +122,7 @@ static s32 ixgbe_reset_hw_X540(struct ixgbe_hw *hw)
status = IXGBE_ERR_RESET_FAILED;
hw_dbg(hw, "Reset polling failed to complete.\n");
}
msleep(50);
msleep(100);
/*
* Double resets are required for recovery from certain error
......@@ -180,6 +164,7 @@ static s32 ixgbe_reset_hw_X540(struct ixgbe_hw *hw)
hw->mac.ops.get_wwn_prefix(hw, &hw->mac.wwnn_prefix,
&hw->mac.wwpn_prefix);
reset_hw_out:
return status;
}
......
include/linux/pci.h
View file @ fb7a6d4e
......@@ -174,6 +174,8 @@ enum pci_dev_flags {
PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG = (__force pci_dev_flags_t) 1,
/* Device configuration is irrevocably lost if disabled into D3 */
PCI_DEV_FLAGS_NO_D3 = (__force pci_dev_flags_t) 2,
/* Provide indication device is assigned by a Virtual Machine Manager */
PCI_DEV_FLAGS_ASSIGNED = (__force pci_dev_flags_t) 4,
};
enum pci_irq_reroute_variant {
......
virt/kvm/assigned-dev.c
View file @ fb7a6d4e
......@@ -205,6 +205,8 @@ static void kvm_free_assigned_device(struct kvm *kvm,
else
pci_restore_state(assigned_dev->dev);
assigned_dev->dev->dev_flags &= ~PCI_DEV_FLAGS_ASSIGNED;
pci_release_regions(assigned_dev->dev);
pci_disable_device(assigned_dev->dev);
pci_dev_put(assigned_dev->dev);
......
virt/kvm/iommu.c
View file @ fb7a6d4e
......@@ -187,6 +187,8 @@ int kvm_assign_device(struct kvm *kvm,
goto out_unmap;
}
pdev->dev_flags |= PCI_DEV_FLAGS_ASSIGNED;
printk(KERN_DEBUG "assign device %x:%x:%x.%x\n",
assigned_dev->host_segnr,
assigned_dev->host_busnr,
......@@ -215,6 +217,8 @@ int kvm_deassign_device(struct kvm *kvm,
iommu_detach_device(domain, &pdev->dev);
pdev->dev_flags &= ~PCI_DEV_FLAGS_ASSIGNED;
printk(KERN_DEBUG "deassign device %x:%x:%x.%x\n",
assigned_dev->host_segnr,
assigned_dev->host_busnr,
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7