Merge tag 'for_3.13_late/dts_signed' of...

Merge tag 'for_3.13_late/dts_signed' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into omap-for-v3.13/dt

Add i2c aliases
Add McASP and audio support
Add reset/idle on init bindings for OMAP
Add more nodes for AM4272

Documentation/devicetree/bindings/arm/omap/omap.txt

@@ -21,7 +21,8 @@ Required properties:
 Optional properties:
 - ti,no_idle_on_suspend: When present, it prevents the PM to idle the module
   during suspend.
-
+- ti,no-reset-on-init: When present, the module should not be reset at init
+- ti,no-idle-on-init: When present, the module should not be idled at init
 
 Example:
 

arch/arm/boot/dts/am335x-evm.dts

@@ -119,6 +119,19 @@ display-timings {
 			};
 		};
 	};
+
+	sound {
+		compatible = "ti,da830-evm-audio";
+		ti,model = "AM335x-EVM";
+		ti,audio-codec = <&tlv320aic3106>;
+		ti,mcasp-controller = <&mcasp1>;
+		ti,codec-clock-rate = <12000000>;
+		ti,audio-routing =
+			"Headphone Jack",       "HPLOUT",
+			"Headphone Jack",       "HPROUT",
+			"LINE1L",               "Line In",
+			"LINE1R",               "Line In";
+	};
 };
 
 &am33xx_pinmux {
@@ -279,6 +292,15 @@ lcd_pins_s0: lcd_pins_s0 {
 			0xec 0x00	/* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */
 		>;
 	};
+
+	am335x_evm_audio_pins: am335x_evm_audio_pins {
+		pinctrl-single,pins = <
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rx_dv.mcasp1_aclkx */
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_txd3.mcasp1_fsx */
+			0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+		>;
+	};
 };
 
 &uart0 {
@@ -373,6 +395,18 @@ tmp275: tmp275@48 {
 		compatible = "ti,tmp275";
 		reg = <0x48>;
 	};
+
+	tlv320aic3106: tlv320aic3106@1b {
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		status = "okay";
+
+		/* Regulators */
+		AVDD-supply = <&vaux2_reg>;
+		IOVDD-supply = <&vaux2_reg>;
+		DRVDD-supply = <&vaux2_reg>;
+		DVDD-supply = <&vbat>;
+	};
 };
 
 &lcdc {
@@ -476,6 +510,22 @@ partition@7 {
 
 #include "tps65910.dtsi"
 
+&mcasp1 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&am335x_evm_audio_pins>;
+
+		status = "okay";
+
+		op-mode = <0>;          /* MCASP_IIS_MODE */
+		tdm-slots = <2>;
+		/* 4 serializers */
+		serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+			0 0 1 2
+		>;
+		tx-num-evt = <1>;
+		rx-num-evt = <1>;
+};
+
 &tps {
 	vcc1-supply = <&vbat>;
 	vcc2-supply = <&vbat>;

arch/arm/boot/dts/am335x-evmsk.dts

@@ -115,6 +115,17 @@ backlight {
 		brightness-levels = <0 58 61 66 75 90 125 170 255>;
 		default-brightness-level = <8>;
 	};
+
+	sound {
+		compatible = "ti,da830-evm-audio";
+		ti,model = "AM335x-EVMSK";
+		ti,audio-codec = <&tlv320aic3106>;
+		ti,mcasp-controller = <&mcasp1>;
+		ti,codec-clock-rate = <24576000>;
+		ti,audio-routing =
+			"Headphone Jack",       "HPLOUT",
+			"Headphone Jack",       "HPROUT";
+	};
 };
 
 &am33xx_pinmux {
@@ -244,6 +255,15 @@ davinci_mdio_sleep: davinci_mdio_sleep {
 			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
 		>;
 	};
+
+	mcasp1_pins: mcasp1_pins {
+		pinctrl-single,pins = <
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */
+			0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+		>;
+	};
 };
 
 &uart0 {
@@ -291,6 +311,18 @@ lis331dlh: lis331dlh@18 {
 		st,max-limit-y = <550>;
 		st,max-limit-z = <750>;
 	};
+
+	tlv320aic3106: tlv320aic3106@1b {
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		status = "okay";
+
+		/* Regulators */
+		AVDD-supply = <&vaux2_reg>;
+		IOVDD-supply = <&vaux2_reg>;
+		DRVDD-supply = <&vaux2_reg>;
+		DVDD-supply = <&vbat>;
+	};
 };
 
 &usb {
@@ -433,3 +465,23 @@ &sham {
 &aes {
 	status = "okay";
 };
+
+&gpio0 {
+	ti,no-reset-on-init;
+};
+
+&mcasp1 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcasp1_pins>;
+
+		status = "okay";
+
+		op-mode = <0>;          /* MCASP_IIS_MODE */
+		tdm-slots = <2>;
+		/* 4 serializers */
+		serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+			0 0 1 2
+		>;
+		tx-num-evt = <1>;
+		rx-num-evt = <1>;
+};

arch/arm/boot/dts/am335x-igep0033.dtsi

@@ -44,6 +44,13 @@ vbat: fixedregulator@0 {
 		regulator-max-microvolt = <5000000>;
 		regulator-boot-on;
 	};
+
+	vmmc: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
 
 &am33xx_pinmux {
@@ -180,6 +187,12 @@ tps: tps@2d {
 	};
 };
 
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmc>;
+	bus-width = <4>;
+};
+
 &uart0 {
 	status = "okay";
 	pinctrl-names = "default";

arch/arm/boot/dts/am33xx.dtsi

@@ -18,6 +18,9 @@ / {
 	interrupt-parent = <&intc>;
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &uart2;
@@ -674,6 +677,7 @@ wkup_m3: wkup_m3@44d00000 {
 			reg = <0x44d00000 0x4000	/* M3 UMEM */
 			       0x44d80000 0x2000>;	/* M3 DMEM */
 			ti,hwmods = "wkup_m3";
+			ti,no-reset-on-init;
 		};
 
 		elm: elm@48080000 {
@@ -713,6 +717,7 @@ am335x_adc: adc {
 		gpmc: gpmc@50000000 {
 			compatible = "ti,am3352-gpmc";
 			ti,hwmods = "gpmc";
+			ti,no-idle-on-init;
 			reg = <0x50000000 0x2000>;
 			interrupts = <100>;
 			gpmc,num-cs = <7>;
@@ -740,5 +745,33 @@ aes: aes@53500000 {
 			       <&edma 5>;
 			dma-names = "tx", "rx";
 		};
+
+		mcasp0: mcasp@48038000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp0";
+			reg = <0x48038000 0x2000>,
+			      <0x46000000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <80>, <81>;
+			interrupts-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 8>,
+				<&edma 9>;
+			dma-names = "tx", "rx";
+		};
+
+		mcasp1: mcasp@4803C000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp1";
+			reg = <0x4803C000 0x2000>,
+			      <0x46400000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <82>, <83>;
+			interrupts-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 10>,
+				<&edma 11>;
+			dma-names = "tx", "rx";
+		};
 	};
 };

arch/arm/boot/dts/am4372.dtsi

@@ -18,7 +18,12 @@ / {
 
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
 		serial0 = &uart0;
+		ethernet0 = &cpsw_emac0;
+		ethernet1 = &cpsw_emac1;
 	};
 
 	cpus {
@@ -39,11 +44,42 @@ gic: interrupt-controller@48241000 {
 		      <0x48240100 0x0100>;
 	};
 
+	l2-cache-controller@48242000 {
+		compatible = "arm,pl310-cache";
+		reg = <0x48242000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+
+	am43xx_pinmux: pinmux@44e10800 {
+		compatible = "pinctrl-single";
+		reg = <0x44e10800 0x31c>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
+
 	ocp {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
+		ti,hwmods = "l3_main";
+
+		edma: edma@49000000 {
+			compatible = "ti,edma3";
+			ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
+			reg =	<0x49000000 0x10000>,
+				<0x44e10f90 0x10>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			dma-channels = <64>;
+			ti,edma-regions = <4>;
+			ti,edma-slots = <256>;
+		};
 
 		uart0: serial@44e09000 {
 			compatible = "ti,am4372-uart","ti,omap2-uart";
@@ -92,6 +128,18 @@ uart5: serial@481aa000 {
 			status = "disabled";
 		};
 
+		mailbox: mailbox@480C8000 {
+			compatible = "ti,omap4-mailbox";
+			reg = <0x480C8000 0x200>;
+			interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mailbox";
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <8>;
+			ti,mbox-names = "wkup_m3";
+			ti,mbox-data = <0 0 0 0>;
+			status = "disabled";
+		};
+
 		timer1: timer@44e31000 {
 			compatible = "ti,am4372-timer-1ms","ti,am335x-timer-1ms";
 			reg = <0x44e31000 0x400>;
@@ -203,7 +251,6 @@ wdt@44e35000 {
 			reg = <0x44e35000 0x1000>;
 			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "wd_timer2";
-			status = "disabled";
 		};
 
 		gpio0: gpio@44e07000 {
@@ -318,6 +365,40 @@ spi0: spi@48030000 {
 			status = "disabled";
 		};
 
+		mmc1: mmc@48060000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x48060000 0x1000>;
+			ti,hwmods = "mmc1";
+			ti,dual-volt;
+			ti,needs-special-reset;
+			dmas = <&edma 24
+				&edma 25>;
+			dma-names = "tx", "rx";
+			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		mmc2: mmc@481d8000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x481d8000 0x1000>;
+			ti,hwmods = "mmc2";
+			ti,needs-special-reset;
+			dmas = <&edma 2
+				&edma 3>;
+			dma-names = "tx", "rx";
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		mmc3: mmc@47810000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x47810000 0x1000>;
+			ti,hwmods = "mmc3";
+			ti,needs-special-reset;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
 		spi1: spi@481a0000 {
 			compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
 			reg = <0x481a0000 0x400>;
@@ -366,50 +447,173 @@ mac: ethernet@4a100000 {
 				      GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH
 				      GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH
 				      GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			ti,hwmods = "cpgmac0";
 			status = "disabled";
+			cpdma_channels = <8>;
+			ale_entries = <1024>;
+			bd_ram_size = <0x2000>;
+			no_bd_ram = <0>;
+			rx_descs = <64>;
+			mac_control = <0x20>;
+			slaves = <2>;
+			active_slave = <0>;
+			cpts_clock_mult = <0x80000000>;
+			cpts_clock_shift = <29>;
+			ranges;
+
+			davinci_mdio: mdio@4a101000 {
+				compatible = "ti,am4372-mdio","ti,davinci_mdio";
+				reg = <0x4a101000 0x100>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				ti,hwmods = "davinci_mdio";
+				bus_freq = <1000000>;
+				status = "disabled";
+			};
+
+			cpsw_emac0: slave@4a100200 {
+				/* Filled in by U-Boot */
+				mac-address = [ 00 00 00 00 00 00 ];
+			};
+
+			cpsw_emac1: slave@4a100300 {
+				/* Filled in by U-Boot */
+				mac-address = [ 00 00 00 00 00 00 ];
+			};
 		};
 
 		epwmss0: epwmss@48300000 {
 			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
 			reg = <0x48300000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 			ti,hwmods = "epwmss0";
 			status = "disabled";
+
+			ecap0: ecap@48300100 {
+				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				reg = <0x48300100 0x80>;
+				ti,hwmods = "ecap0";
+				status = "disabled";
+			};
+
+			ehrpwm0: ehrpwm@48300200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				reg = <0x48300200 0x80>;
+				ti,hwmods = "ehrpwm0";
+				status = "disabled";
+			};
 		};
 
 		epwmss1: epwmss@48302000 {
 			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
 			reg = <0x48302000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 			ti,hwmods = "epwmss1";
 			status = "disabled";
+
+			ecap1: ecap@48302100 {
+				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				reg = <0x48302100 0x80>;
+				ti,hwmods = "ecap1";
+				status = "disabled";
+			};
+
+			ehrpwm1: ehrpwm@48302200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				reg = <0x48302200 0x80>;
+				ti,hwmods = "ehrpwm1";
+				status = "disabled";
+			};
 		};
 
 		epwmss2: epwmss@48304000 {
 			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
 			reg = <0x48304000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 			ti,hwmods = "epwmss2";
 			status = "disabled";
+
+			ecap2: ecap@48304100 {
+				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				reg = <0x48304100 0x80>;
+				ti,hwmods = "ecap2";
+				status = "disabled";
+			};
+
+			ehrpwm2: ehrpwm@48304200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				reg = <0x48304200 0x80>;
+				ti,hwmods = "ehrpwm2";
+				status = "disabled";
+			};
 		};
 
 		epwmss3: epwmss@48306000 {
 			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
 			reg = <0x48306000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 			ti,hwmods = "epwmss3";
 			status = "disabled";
+
+			ehrpwm3: ehrpwm@48306200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				reg = <0x48306200 0x80>;
+				ti,hwmods = "ehrpwm3";
+				status = "disabled";
+			};
 		};
 
 		epwmss4: epwmss@48308000 {
 			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
 			reg = <0x48308000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 			ti,hwmods = "epwmss4";
 			status = "disabled";
+
+			ehrpwm4: ehrpwm@48308200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				reg = <0x48308200 0x80>;
+				ti,hwmods = "ehrpwm4";
+				status = "disabled";
+			};
 		};
 
 		epwmss5: epwmss@4830a000 {
 			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
 			reg = <0x4830a000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 			ti,hwmods = "epwmss5";
 			status = "disabled";
+
+			ehrpwm5: ehrpwm@4830a200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				reg = <0x4830a200 0x80>;
+				ti,hwmods = "ehrpwm5";
+				status = "disabled";
+			};
+		};
+
+		sham: sham@53100000 {
+			compatible = "ti,omap5-sham";
+			ti,hwmods = "sham";
+			reg = <0x53100000 0x300>;
+			dmas = <&edma 36>;
+			dma-names = "rx";
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		aes: aes@53501000 {
@@ -417,6 +621,9 @@ aes: aes@53501000 {
 			ti,hwmods = "aes";
 			reg = <0x53501000 0xa0>;
 			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&edma 6
+				&edma 5>;
+			dma-names = "tx", "rx";
 		};
 
 		des: des@53701000 {
@@ -424,6 +631,37 @@ des: des@53701000 {
 			ti,hwmods = "des";
 			reg = <0x53701000 0xa0>;
 			interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&edma 34
+				&edma 33>;
+			dma-names = "tx", "rx";
+		};
+
+		mcasp0: mcasp@48038000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp0";
+			reg = <0x48038000 0x2000>,
+			      <0x46000000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <80>, <81>;
+			interrupts-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 8>,
+			       <&edma 9>;
+			dma-names = "tx", "rx";
+		};
+
+		mcasp1: mcasp@4803C000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp1";
+			reg = <0x4803C000 0x2000>,
+			      <0x46400000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <82>, <83>;
+			interrupts-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 10>,
+			       <&edma 11>;
+			dma-names = "tx", "rx";
 		};
 	};
 };

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -11,8 +11,176 @@
 /dts-v1/;
 
 #include "am4372.dtsi"
+#include <dt-bindings/pinctrl/am43xx.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "TI AM43x EPOS EVM";
 	compatible = "ti,am43x-epos-evm","ti,am4372","ti,am43";
+
+	vmmcsd_fixed: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+	};
+
+	am43xx_pinmux: pinmux@44e10800 {
+		cpsw_default: cpsw_default {
+			pinctrl-single,pins = <
+				/* Slave 1 */
+				0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_crs.rmii1_crs */
+				0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxerr.rmii1_rxerr */
+				0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_txen.rmii1_txen */
+				0x118 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxdv.rmii1_rxdv */
+				0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_txd1.rmii1_txd1 */
+				0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_txd0.rmii1_txd0 */
+				0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxd1.rmii1_rxd1 */
+				0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxd0.rmii1_rxd0 */
+				0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* rmii1_refclk.rmii1_refclk */
+			>;
+		};
+
+		cpsw_sleep: cpsw_sleep {
+			pinctrl-single,pins = <
+				/* Slave 1 reset value */
+				0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			>;
+		};
+
+		davinci_mdio_default: davinci_mdio_default {
+			pinctrl-single,pins = <
+				/* MDIO */
+				0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+				0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
+			>;
+		};
+
+		davinci_mdio_sleep: davinci_mdio_sleep {
+			pinctrl-single,pins = <
+				/* MDIO reset value */
+				0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+				0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			>;
+		};
+
+		i2c0_pins: pinmux_i2c0_pins {
+			pinctrl-single,pins = <
+				0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+				0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+			>;
+		};
+	};
+
+	matrix_keypad: matrix_keypad@0 {
+			compatible = "gpio-matrix-keypad";
+			debounce-delay-ms = <5>;
+			col-scan-delay-us = <2>;
+
+			row-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH		/* Bank0, pin12 */
+				     &gpio0 13 GPIO_ACTIVE_HIGH		/* Bank0, pin13 */
+				     &gpio0 14 GPIO_ACTIVE_HIGH		/* Bank0, pin14 */
+				     &gpio0 15 GPIO_ACTIVE_HIGH>;	/* Bank0, pin15 */
+
+			col-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH		/* Bank3, pin9 */
+				     &gpio3 10 GPIO_ACTIVE_HIGH		/* Bank3, pin10 */
+				     &gpio2 18 GPIO_ACTIVE_HIGH		/* Bank2, pin18 */
+				     &gpio2 19 GPIO_ACTIVE_HIGH>;	/* Bank2, pin19 */
+
+			linux,keymap = <0x00000201	/* P1 */
+				0x01000204	/* P4 */
+				0x02000207	/* P7 */
+				0x0300020a	/* NUMERIC_STAR */
+				0x00010202	/* P2 */
+				0x01010205	/* P5 */
+				0x02010208	/* P8 */
+				0x03010200	/* P0 */
+				0x00020203	/* P3 */
+				0x01020206	/* P6 */
+				0x02020209	/* P9 */
+				0x0302020b	/* NUMERIC_POUND */
+				0x00030067	/* UP */
+				0x0103006a	/* RIGHT */
+				0x0203006c	/* DOWN */
+				0x03030069>;	/* LEFT */
+		};
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+};
+
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <16>;
+	phy-mode = "rmii";
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <1>;
+	phy-mode = "rmii";
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	at24@50 {
+		compatible = "at24,24c256";
+		pagesize = <64>;
+		reg = <0x50>;
+	};
+
+	pixcir_ts@5c {
+		compatible = "pixcir,pixcir_ts";
+		reg = <0x5c>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <17 0>;
+
+		attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+
+		x-size = <1024>;
+		y-size = <768>;
+	};
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&gpio3 {
+	status = "okay";
 };

arch/arm/boot/dts/dra7.dtsi

@@ -20,6 +20,11 @@ / {
 	interrupt-parent = <&gic>;
 
 	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
+		i2c4 = &i2c5;
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;

arch/arm/boot/dts/omap3-beagle.dts

@@ -173,6 +173,8 @@ &gpio1 {
 &usb_otg_hs {
 	interface-type = <0>;
 	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
 	mode = <3>;
 	power = <50>;
 };

arch/arm/boot/dts/omap3-gta04.dts

@@ -131,6 +131,8 @@ &i2c3 {
 &usb_otg_hs {
 	interface-type = <0>;
 	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
 	mode = <3>;
 	power = <50>;
 };

arch/arm/boot/dts/omap3-n900.dts

@@ -87,6 +87,8 @@ mipid@2 {
 &usb_otg_hs {
 	interface-type = <0>;
 	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
 	mode = <2>;
 	power = <50>;
 };

arch/arm/boot/dts/omap3.dtsi

@@ -19,6 +19,9 @@ / {
 	interrupt-parent = <&intc>;
 
 	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;

arch/arm/boot/dts/omap4-panda-es.dts

@@ -62,3 +62,7 @@ mmc {
 		gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 	};
 };
+
+&gpio1 {
+	 ti,no-reset-on-init;
+};

arch/arm/boot/dts/omap4.dtsi

@@ -17,6 +17,10 @@ / {
 	interrupt-parent = <&gic>;
 
 	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;
@@ -214,6 +218,7 @@ gpmc: gpmc@50000000 {
 			gpmc,num-cs = <8>;
 			gpmc,num-waitpins = <4>;
 			ti,hwmods = "gpmc";
+			ti,no-idle-on-init;
 		};
 
 		uart1: serial@4806a000 {
@@ -492,6 +497,7 @@ emif1: emif@4c000000 {
 			reg = <0x4c000000 0x100>;
 			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "emif1";
+			ti,no-idle-on-init;
 			phy-type = <1>;
 			hw-caps-read-idle-ctrl;
 			hw-caps-ll-interface;
@@ -503,6 +509,7 @@ emif2: emif@4d000000 {
 			reg = <0x4d000000 0x100>;
 			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "emif2";
+			ti,no-idle-on-init;
 			phy-type = <1>;
 			hw-caps-read-idle-ctrl;
 			hw-caps-ll-interface;

arch/arm/boot/dts/omap5-uevm.dts

@@ -334,8 +334,6 @@ smps10_out1_reg: smps10_out1 {
 					regulator-name = "smps10_out1";
 					regulator-min-microvolt = <5000000>;
 					regulator-max-microvolt = <5000000>;
-					regulator-always-on;
-					regulator-boot-on;
 				};
 
 				ldo1_reg: ldo1 {

arch/arm/boot/dts/omap5.dtsi

@@ -21,6 +21,11 @@ / {
 	interrupt-parent = <&gic>;
 
 	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
+		i2c4 = &i2c5;
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;
@@ -52,7 +57,6 @@ timer {
 			     <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>;
-		clock-frequency = <6144000>;
 	};
 
 	gic: interrupt-controller@48211000 {
@@ -607,6 +611,7 @@ wdt2: wdt@4ae14000 {
 		emif1: emif@4c000000 {
 			compatible	= "ti,emif-4d5";
 			ti,hwmods	= "emif1";
+			ti,no-idle-on-init;
 			phy-type	= <2>; /* DDR PHY type: Intelli PHY */
 			reg = <0x4c000000 0x400>;
 			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
@@ -618,6 +623,7 @@ emif1: emif@4c000000 {
 		emif2: emif@4d000000 {
 			compatible	= "ti,emif-4d5";
 			ti,hwmods	= "emif2";
+			ti,no-idle-on-init;
 			phy-type	= <2>; /* DDR PHY type: Intelli PHY */
 			reg = <0x4d000000 0x400>;
 			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
@@ -648,6 +654,7 @@ dwc3@4a030000 {
 				reg = <0x4a030000 0x10000>;
 				interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
 				usb-phy = <&usb2_phy>, <&usb3_phy>;
+				dr_mode = "peripheral";
 				tx-fifo-resize;
 			};
 		};

include/dt-bindings/pinctrl/am43xx.h

+/*
+ * This header provides constants specific to AM43XX pinctrl bindings.
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_AM43XX_H
+#define _DT_BINDINGS_PINCTRL_AM43XX_H
+
+#define MUX_MODE0	0
+#define MUX_MODE1	1
+#define MUX_MODE2	2
+#define MUX_MODE3	3
+#define MUX_MODE4	4
+#define MUX_MODE5	5
+#define MUX_MODE6	6
+#define MUX_MODE7	7
+
+#define PULL_DISABLE		(1 << 16)
+#define PULL_UP			(1 << 17)
+#define INPUT_EN		(1 << 18)
+#define SLEWCTRL_FAST		(1 << 19)
+#define DS0_PULL_UP_DOWN_EN	(1 << 27)
+
+#define PIN_OUTPUT		(PULL_DISABLE)
+#define PIN_OUTPUT_PULLUP	(PULL_UP)
+#define PIN_OUTPUT_PULLDOWN	0
+#define PIN_INPUT		(INPUT_EN | PULL_DISABLE)
+#define PIN_INPUT_PULLUP	(INPUT_EN | PULL_UP)
+#define PIN_INPUT_PULLDOWN	(INPUT_EN)
+
+#endif
+