Merge tag 'omap-for-v4.8/fixes-rc2' of...

Merge tag 'omap-for-v4.8/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.8-rc cycle, mostly a series of four fixes for
am335x RTC zero offset for clkctrl register. Also few other fixes:

- Add missing sysc information for DSI as at least n950 needs it for
  the working display

- Fix old elm-id properties that cause nand boot to not work

- Fix overo gpmc nand cs0 range

- FIx overo gpmc nand on boards with ethernet

- Fix logicpd torpedo nand ready pin nand interrupt configuration

* tag 'omap-for-v4.8/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: logicpd-somlv: Fix NAND device nodes
  ARM: dts: logicpd-torpedo-som: Provide NAND ready pin
  ARM: dts: overo: fix gpmc nand on boards with ethernet
  ARM: dts: overo: fix gpmc nand cs0 range
  ARM: dts: am335x: Update elm phandle binding
  ARM: OMAP4+: CM: Remove redundant checks for clkctrl_offs of zero
  ARM: OMAP4+: Have _omap4_wait_target_* check for valid clkctrl_offs
  ARM: OMAP2+: AM33XX: Add HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET flag to rtc hwmod
  ARM: OMAP4+: hwmod: Add hwmod flag for HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET
  ARM: OMAP3: hwmod data: Add sysc information for DSI
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/am335x-baltos.dtsi

@@ -226,7 +226,7 @@ nand@0,0 {
 
 		#address-cells = <1>;
 		#size-cells = <1>;
-		elm_id = <&elm>;
+		ti,elm-id = <&elm>;
 	};
 };
 

arch/arm/boot/dts/am335x-igep0033.dtsi

@@ -161,7 +161,7 @@ nand@0,0 {
 
 		#address-cells = <1>;
 		#size-cells = <1>;
-		elm_id = <&elm>;
+		ti,elm-id = <&elm>;
 
 		/* MTD partition table */
 		partition@0 {

arch/arm/boot/dts/am335x-phycore-som.dtsi

@@ -197,7 +197,7 @@ nandflash: nand@0,0 {
 		gpmc,wr-access-ns = <30>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 
-		elm_id = <&elm>;
+		ti,elm-id = <&elm>;
 
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm/boot/dts/logicpd-som-lv.dtsi

@@ -35,10 +35,15 @@ &gpmc {
 	ranges = <0 0 0x00000000 0x1000000>;	/* CS0: 16MB for NAND */
 
 	nand@0,0 {
-		linux,mtd-name = "micron,mt29f4g16abbda3w";
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
+		linux,mtd-name = "micron,mt29f4g16abbda3w";
 		nand-bus-width = <16>;
 		ti,nand-ecc-opt = "bch8";
+		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <44>;
@@ -54,10 +59,6 @@ nand@0,0 {
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 		gpmc,device-width = <2>;
-
-		gpmc,page-burst-access-ns = <5>;
-		gpmc,cycle2cycle-delay-ns = <50>;
-
 		#address-cells = <1>;
 		#size-cells = <1>;
 

arch/arm/boot/dts/logicpd-torpedo-som.dtsi

@@ -46,6 +46,7 @@ nand@0,0 {
 		linux,mtd-name = "micron,mt29f4g16abbda3w";
 		nand-bus-width = <16>;
 		ti,nand-ecc-opt = "bch8";
+		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <44>;

arch/arm/boot/dts/omap3-overo-base.dtsi

@@ -223,7 +223,9 @@ &mcbsp2 {
 };
 
 &gpmc {
-	ranges = <0 0 0x00000000 0x20000000>;
+	ranges = <0 0 0x30000000 0x1000000>,	/* CS0 */
+		 <4 0 0x2b000000 0x1000000>,	/* CS4 */
+		 <5 0 0x2c000000 0x1000000>;	/* CS5 */
 
 	nand@0,0 {
 		compatible = "ti,omap2-nand";

arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi

@@ -55,8 +55,6 @@ button1@14 {
 #include "omap-gpmc-smsc9221.dtsi"
 
 &gpmc {
-	ranges = <5 0 0x2c000000 0x1000000>;	/* CS5 */
-
 	ethernet@gpmc {
 		reg = <5 0 0xff>;
 		interrupt-parent = <&gpio6>;

arch/arm/boot/dts/omap3-overo-tobi-common.dtsi

@@ -27,8 +27,6 @@ heartbeat {
 #include "omap-gpmc-smsc9221.dtsi"
 
 &gpmc {
-	ranges = <5 0 0x2c000000 0x1000000>;	/* CS5 */
-
 	ethernet@gpmc {
 		reg = <5 0 0xff>;
 		interrupt-parent = <&gpio6>;

arch/arm/boot/dts/omap3-overo-tobiduo-common.dtsi

@@ -15,9 +15,6 @@
 #include "omap-gpmc-smsc9221.dtsi"
 
 &gpmc {
-	ranges = <4 0 0x2b000000 0x1000000>,	/* CS4 */
-		 <5 0 0x2c000000 0x1000000>;	/* CS5 */
-
 	smsc1: ethernet@gpmc {
 		reg = <5 0 0xff>;
 		interrupt-parent = <&gpio6>;

arch/arm/mach-omap2/cm33xx.c

@@ -220,9 +220,6 @@ static int am33xx_cm_wait_module_ready(u8 part, s16 inst, u16 clkctrl_offs,
 {
 	int i = 0;
 
-	if (!clkctrl_offs)
-		return 0;
-
 	omap_test_timeout(_is_module_ready(inst, clkctrl_offs),
 			  MAX_MODULE_READY_TIME, i);
 
@@ -246,9 +243,6 @@ static int am33xx_cm_wait_module_idle(u8 part, s16 inst, u16 clkctrl_offs,
 {
 	int i = 0;
 
-	if (!clkctrl_offs)
-		return 0;
-
 	omap_test_timeout((_clkctrl_idlest(inst, clkctrl_offs) ==
 				CLKCTRL_IDLEST_DISABLED),
 				MAX_MODULE_READY_TIME, i);

arch/arm/mach-omap2/cminst44xx.c

@@ -278,9 +278,6 @@ static int omap4_cminst_wait_module_ready(u8 part, s16 inst, u16 clkctrl_offs,
 {
 	int i = 0;
 
-	if (!clkctrl_offs)
-		return 0;
-
 	omap_test_timeout(_is_module_ready(part, inst, clkctrl_offs),
 			  MAX_MODULE_READY_TIME, i);
 
@@ -304,9 +301,6 @@ static int omap4_cminst_wait_module_idle(u8 part, s16 inst, u16 clkctrl_offs,
 {
 	int i = 0;
 
-	if (!clkctrl_offs)
-		return 0;
-
 	omap_test_timeout((_clkctrl_idlest(part, inst, clkctrl_offs) ==
 			   CLKCTRL_IDLEST_DISABLED),
 			  MAX_MODULE_DISABLE_TIME, i);

arch/arm/mach-omap2/omap_hwmod.c

@@ -1053,6 +1053,10 @@ static int _omap4_wait_target_disable(struct omap_hwmod *oh)
 	if (oh->flags & HWMOD_NO_IDLEST)
 		return 0;
 
+	if (!oh->prcm.omap4.clkctrl_offs &&
+	    !(oh->prcm.omap4.flags & HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET))
+		return 0;
+
 	return omap_cm_wait_module_idle(oh->clkdm->prcm_partition,
 					oh->clkdm->cm_inst,
 					oh->prcm.omap4.clkctrl_offs, 0);
@@ -2971,6 +2975,10 @@ static int _omap4_wait_target_ready(struct omap_hwmod *oh)
 	if (!_find_mpu_rt_port(oh))
 		return 0;
 
+	if (!oh->prcm.omap4.clkctrl_offs &&
+	    !(oh->prcm.omap4.flags & HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET))
+		return 0;
+
 	/* XXX check module SIDLEMODE, hardreset status */
 
 	return omap_cm_wait_module_ready(oh->clkdm->prcm_partition,

arch/arm/mach-omap2/omap_hwmod.h

@@ -443,8 +443,12 @@ struct omap_hwmod_omap2_prcm {
  * HWMOD_OMAP4_NO_CONTEXT_LOSS_BIT: Some IP blocks don't have a PRCM
  *     module-level context loss register associated with them; this
  *     flag bit should be set in those cases
+ * HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET: Some IP blocks have a valid CLKCTRL
+ *	offset of zero; this flag bit should be set in those cases to
+ *	distinguish from hwmods that have no clkctrl offset.
  */
 #define HWMOD_OMAP4_NO_CONTEXT_LOSS_BIT		(1 << 0)
+#define HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET		(1 << 1)
 
 /**
  * struct omap_hwmod_omap4_prcm - OMAP4-specific PRCM data

arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c

@@ -29,6 +29,7 @@
 #define CLKCTRL(oh, clkctrl) ((oh).prcm.omap4.clkctrl_offs = (clkctrl))
 #define RSTCTRL(oh, rstctrl) ((oh).prcm.omap4.rstctrl_offs = (rstctrl))
 #define RSTST(oh, rstst) ((oh).prcm.omap4.rstst_offs = (rstst))
+#define PRCM_FLAGS(oh, flag) ((oh).prcm.omap4.flags = (flag))
 
 /*
  * 'l3' class
@@ -1296,6 +1297,7 @@ static void omap_hwmod_am33xx_clkctrl(void)
 	CLKCTRL(am33xx_i2c1_hwmod, AM33XX_CM_WKUP_I2C0_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_wd_timer1_hwmod, AM33XX_CM_WKUP_WDT1_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_rtc_hwmod, AM33XX_CM_RTC_RTC_CLKCTRL_OFFSET);
+	PRCM_FLAGS(am33xx_rtc_hwmod, HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_mmc2_hwmod, AM33XX_CM_PER_MMC2_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_gpmc_hwmod, AM33XX_CM_PER_GPMC_CLKCTRL_OFFSET);
 	CLKCTRL(am33xx_l4_ls_hwmod, AM33XX_CM_PER_L4LS_CLKCTRL_OFFSET);

arch/arm/mach-omap2/omap_hwmod_3xxx_data.c

@@ -722,8 +722,20 @@ static struct omap_hwmod omap3xxx_dss_dispc_hwmod = {
  * display serial interface controller
  */
 
+static struct omap_hwmod_class_sysconfig omap3xxx_dsi_sysc = {
+	.rev_offs	= 0x0000,
+	.sysc_offs	= 0x0010,
+	.syss_offs	= 0x0014,
+	.sysc_flags	= (SYSC_HAS_AUTOIDLE | SYSC_HAS_CLOCKACTIVITY |
+			   SYSC_HAS_ENAWAKEUP | SYSC_HAS_SIDLEMODE |
+			   SYSC_HAS_SOFTRESET | SYSS_HAS_RESET_STATUS),
+	.idlemodes	= (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART),
+	.sysc_fields	= &omap_hwmod_sysc_type1,
+};
+
 static struct omap_hwmod_class omap3xxx_dsi_hwmod_class = {
 	.name = "dsi",
+	.sysc	= &omap3xxx_dsi_sysc,
 };
 
 static struct omap_hwmod_irq_info omap3xxx_dsi1_irqs[] = {