component/slapos/obs.cfg: fix after perl version up

This is a fixup of f6281e7a.

component/slapos/obs.cfg

@@ -44,23 +44,23 @@ configure-options +=
 make-options +=
   DESTDIR=${buildout:destdir}
 environment +=
-  PERL5LIB=${perl:location}/lib/5.28.1/
+  PERL5LIB=${perl:location}/lib/5.38.0/
 
 [intltool]
 environment +=
-  PERL5LIB=${perl:location}/lib/5.28.1/
+  PERL5LIB=${perl:location}/lib/5.38.0/
 
 [autoconf]
 environment +=
-  PERL5LIB=${perl:location}/lib/5.28.1/
+  PERL5LIB=${perl:location}/lib/5.38.0/
 
 [automake]
 environment +=
-  PERL5LIB=${perl:location}/lib/5.28.1/
+  PERL5LIB=${perl:location}/lib/5.38.0/
 
 [firewalld]
 environment +=
-  PERL5LIB=${perl:location}/lib/5.28.1/
+  PERL5LIB=${perl:location}/lib/5.38.0/
 
 
 [dbus]
@@ -97,7 +97,7 @@ make-options +=
   INSTALL_PREFIX=${buildout:destdir}
   DESTDIR=${buildout:destdir}
 environment +=
-  PERL5LIB=${perl:location}/lib/5.28.1/
+  PERL5LIB=${perl:location}/lib/5.38.0/
 
 [gobject-introspection]
 pre-configure =
@@ -105,7 +105,7 @@ pre-configure =
 configure-options +=
   --enable-shared
 environment +=
-  PERL5LIB=${perl:location}/lib/5.28.1/
+  PERL5LIB=${perl:location}/lib/5.38.0/
 post-install =
   sed -i 's#!${python:location}/bin/python${python:version}#!/opt/slapos/parts/python${python:version}/bin/python${python:version}#' ${python:location}/bin/python${python:version}-config
 
@@ -121,14 +121,14 @@ environment +=
 
 
 [perl-CPAN-package]
-perl-PERL5LIB=${perl:location}/lib/5.28.1/
+perl-PERL5LIB=${perl:location}/lib/5.38.0/
 
 pre-configure =
-  sed -i "s#'/opt/slapos/parts/perl#'${perl:location}#" ${perl:location}/lib/5.28.1/*-linux-thread-multi/Config.pm
-  sed -i "s#'/opt/slapos/parts/site_perl#'${buildout:destdir}/parts/site_perl#" ${perl:location}/lib/5.28.1/*-linux-thread-multi/Config.pm
+  sed -i "s#'/opt/slapos/parts/perl#'${perl:location}#" ${perl:location}/lib/5.38.0/*-linux-thread-multi/Config.pm
+  sed -i "s#'/opt/slapos/parts/site_perl#'${buildout:destdir}/parts/site_perl#" ${perl:location}/lib/5.38.0/*-linux-thread-multi/Config.pm
 post-install =
-  sed -i "s#'${perl:location}#'/opt/slapos/parts/perl#" ${perl:location}/lib/5.28.1/*-linux-thread-multi/Config.pm
-  sed -i "s#'${buildout:destdir}/parts/site_perl#'/opt/slapos/parts/site_perl#" ${perl:location}/lib/5.28.1/*-linux-thread-multi/Config.pm
+  sed -i "s#'${perl:location}#'/opt/slapos/parts/perl#" ${perl:location}/lib/5.38.0/*-linux-thread-multi/Config.pm
+  sed -i "s#'${buildout:destdir}/parts/site_perl#'/opt/slapos/parts/site_perl#" ${perl:location}/lib/5.38.0/*-linux-thread-multi/Config.pm
 
 [perl]
 configure-command =