Merge kroah.com:/home/greg/linux/BK/bleed-2.5

into kroah.com:/home/greg/linux/BK/gregkh-2.5

drivers/usb/net/usbnet.c

@@ -1701,6 +1701,15 @@ static const struct driver_info	zaurus_slb500_info = {
 
 	.in = 1, .out = 2,
 };
+static const struct driver_info zaurus_slc700_info = {
+    .description =  "Sharp Zaurus SL-C700",
+    .flags =    FLAG_FRAMING_Z,
+    .check_connect = always_connected,
+    .tx_fixup =     zaurus_tx_fixup,
+
+    .in = 1, .out = 2,
+};
+
 
 // SL-5600 and C-700 are PXA based; should resemble A300
 
@@ -2751,6 +2760,15 @@ static const struct usb_device_id	products [] = {
 	.bInterfaceSubClass	= 0x0a,
 	.bInterfaceProtocol	= 0x00,
 	.driver_info =  (unsigned long) &zaurus_slb500_info,
+}, {
+	.match_flags    =   USB_DEVICE_ID_MATCH_INT_INFO
+	          | USB_DEVICE_ID_MATCH_DEVICE,
+	.idVendor       = 0x04DD,
+	.idProduct      = 0x8007,
+	.bInterfaceClass    = 0x02,
+	.bInterfaceSubClass = 0x0a,
+	.bInterfaceProtocol = 0x00,
+	.driver_info =  (unsigned long) &zaurus_slc700_info,
 },
 #endif
 

drivers/usb/storage/scsiglue.c

@@ -166,6 +166,10 @@ static int device_reset( Scsi_Cmnd *srb )
 
 	/* lock the device pointers and do the reset */
 	down(&(us->dev_semaphore));
+	if (test_bit(US_FLIDX_DISCONNECTING, &us->flags)) {
+		result = FAILED;
+		US_DEBUGP("No reset during disconnect\n");
+	} else
 		result = us->transport_reset(us);
 	up(&(us->dev_semaphore));
 
@@ -202,7 +206,7 @@ static int bus_reset( Scsi_Cmnd *srb )
 	down(&(us->dev_semaphore));
 	if (test_bit(US_FLIDX_DISCONNECTING, &us->flags)) {
 		result = -EIO;
-		US_DEBUGP("Attempt to reset during disconnect\n");
+		US_DEBUGP("No reset during disconnect\n");
 	} else if (us->pusb_dev->actconfig->desc.bNumInterfaces != 1) {
 		result = -EBUSY;
 		US_DEBUGP("Refusing to reset a multi-interface device\n");

drivers/usb/storage/transport.c

@@ -147,9 +147,19 @@ static int usb_stor_msg_common(struct us_data *us, int timeout)
 	us->current_urb->context = &urb_done;
 	us->current_urb->actual_length = 0;
 	us->current_urb->error_count = 0;
-	us->current_urb->transfer_flags = URB_ASYNC_UNLINK;
 	us->current_urb->status = 0;
 
+	/* we assume that if transfer_buffer isn't us->iobuf then it
+	 * hasn't been mapped for DMA.  Yes, this is clunky, but it's
+	 * easier than always having the caller tell us whether the
+	 * transfer buffer has already been mapped. */
+	us->current_urb->transfer_flags =
+			URB_ASYNC_UNLINK | URB_NO_SETUP_DMA_MAP;
+	if (us->current_urb->transfer_buffer == us->iobuf)
+		us->current_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
+	us->current_urb->transfer_dma = us->iobuf_dma;
+	us->current_urb->setup_dma = us->cr_dma;
+
 	/* submit the URB */
 	status = usb_submit_urb(us->current_urb, GFP_NOIO);
 	if (status) {
@@ -207,15 +217,15 @@ int usb_stor_control_msg(struct us_data *us, unsigned int pipe,
 			value, index, size);
 
 	/* fill in the devrequest structure */
-	us->dr->bRequestType = requesttype;
-	us->dr->bRequest = request;
-	us->dr->wValue = cpu_to_le16(value);
-	us->dr->wIndex = cpu_to_le16(index);
-	us->dr->wLength = cpu_to_le16(size);
+	us->cr->bRequestType = requesttype;
+	us->cr->bRequest = request;
+	us->cr->wValue = cpu_to_le16(value);
+	us->cr->wIndex = cpu_to_le16(index);
+	us->cr->wLength = cpu_to_le16(size);
 
 	/* fill and submit the URB */
 	usb_fill_control_urb(us->current_urb, us->pusb_dev, pipe, 
-			 (unsigned char*) us->dr, data, size, 
+			 (unsigned char*) us->cr, data, size, 
 			 usb_stor_blocking_completion, NULL);
 	status = usb_stor_msg_common(us, timeout);
 
@@ -346,15 +356,15 @@ int usb_stor_ctrl_transfer(struct us_data *us, unsigned int pipe,
 			value, index, size);
 
 	/* fill in the devrequest structure */
-	us->dr->bRequestType = requesttype;
-	us->dr->bRequest = request;
-	us->dr->wValue = cpu_to_le16(value);
-	us->dr->wIndex = cpu_to_le16(index);
-	us->dr->wLength = cpu_to_le16(size);
+	us->cr->bRequestType = requesttype;
+	us->cr->bRequest = request;
+	us->cr->wValue = cpu_to_le16(value);
+	us->cr->wIndex = cpu_to_le16(index);
+	us->cr->wLength = cpu_to_le16(size);
 
 	/* fill and submit the URB */
 	usb_fill_control_urb(us->current_urb, us->pusb_dev, pipe, 
-			 (unsigned char*) us->dr, data, size, 
+			 (unsigned char*) us->cr, data, size, 
 			 usb_stor_blocking_completion, NULL);
 	result = usb_stor_msg_common(us, 0);
 
@@ -786,9 +796,9 @@ int usb_stor_CBI_transport(Scsi_Cmnd *srb, struct us_data *us)
 	}
 
 	/* STATUS STAGE */
-	result = usb_stor_intr_transfer(us, us->irqdata, sizeof(us->irqdata));
+	result = usb_stor_intr_transfer(us, us->iobuf, 2);
 	US_DEBUGP("Got interrupt data (0x%x, 0x%x)\n", 
-			us->irqdata[0], us->irqdata[1]);
+			us->iobuf[0], us->iobuf[1]);
 	if (result != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_ERROR;
 
@@ -804,7 +814,7 @@ int usb_stor_CBI_transport(Scsi_Cmnd *srb, struct us_data *us)
 		    srb->cmnd[0] == INQUIRY)
 			return USB_STOR_TRANSPORT_GOOD;
 		else {
-			if (us->irqdata[0])
+			if (us->iobuf[0])
 				return USB_STOR_TRANSPORT_FAILED;
 			else
 				return USB_STOR_TRANSPORT_GOOD;
@@ -815,13 +825,13 @@ int usb_stor_CBI_transport(Scsi_Cmnd *srb, struct us_data *us)
 	 * The first byte should always be a 0x0
 	 * The second byte & 0x0F should be 0x0 for good, otherwise error 
 	 */
-	if (us->irqdata[0]) {
+	if (us->iobuf[0]) {
 		US_DEBUGP("CBI IRQ data showed reserved bType %d\n",
-				us->irqdata[0]);
+				us->iobuf[0]);
 		return USB_STOR_TRANSPORT_ERROR;
 	}
 
-	switch (us->irqdata[1] & 0x0F) {
+	switch (us->iobuf[1] & 0x0F) {
 		case 0x00: 
 			return USB_STOR_TRANSPORT_GOOD;
 		case 0x01: 
@@ -889,7 +899,6 @@ int usb_stor_CB_transport(Scsi_Cmnd *srb, struct us_data *us)
 /* Determine what the maximum LUN supported is */
 int usb_stor_Bulk_max_lun(struct us_data *us)
 {
-	unsigned char data;
 	int result;
 
 	/* issue the command */
@@ -897,14 +906,14 @@ int usb_stor_Bulk_max_lun(struct us_data *us)
 				 US_BULK_GET_MAX_LUN, 
 				 USB_DIR_IN | USB_TYPE_CLASS | 
 				 USB_RECIP_INTERFACE,
-				 0, us->ifnum, &data, sizeof(data), HZ);
+				 0, us->ifnum, us->iobuf, 1, HZ);
 
 	US_DEBUGP("GetMaxLUN command result is %d, data is %d\n", 
-		  result, data);
+		  result, us->iobuf[0]);
 
 	/* if we have a successful request, return the result */
 	if (result == 1)
-		return data;
+		return us->iobuf[0];
 
 	/* return the default -- no LUNs */
 	return 0;
@@ -912,33 +921,34 @@ int usb_stor_Bulk_max_lun(struct us_data *us)
 
 int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 {
-	struct bulk_cb_wrap bcb;
-	struct bulk_cs_wrap bcs;
+	struct bulk_cb_wrap *bcb = (struct bulk_cb_wrap *) us->iobuf;
+	struct bulk_cs_wrap *bcs = (struct bulk_cs_wrap *) us->iobuf;
 	unsigned int transfer_length = srb->request_bufflen;
 	int result;
 	int fake_sense = 0;
 
 	/* set up the command wrapper */
-	bcb.Signature = cpu_to_le32(US_BULK_CB_SIGN);
-	bcb.DataTransferLength = cpu_to_le32(transfer_length);
-	bcb.Flags = srb->sc_data_direction == SCSI_DATA_READ ? 1 << 7 : 0;
-	bcb.Tag = srb->serial_number;
-	bcb.Lun = srb->device->lun;
+	bcb->Signature = cpu_to_le32(US_BULK_CB_SIGN);
+	bcb->DataTransferLength = cpu_to_le32(transfer_length);
+	bcb->Flags = srb->sc_data_direction == SCSI_DATA_READ ? 1 << 7 : 0;
+	bcb->Tag = srb->serial_number;
+	bcb->Lun = srb->device->lun;
 	if (us->flags & US_FL_SCM_MULT_TARG)
-		bcb.Lun |= srb->device->id << 4;
-	bcb.Length = srb->cmd_len;
+		bcb->Lun |= srb->device->id << 4;
+	bcb->Length = srb->cmd_len;
 
 	/* copy the command payload */
-	memset(bcb.CDB, 0, sizeof(bcb.CDB));
-	memcpy(bcb.CDB, srb->cmnd, bcb.Length);
+	memset(bcb->CDB, 0, sizeof(bcb->CDB));
+	memcpy(bcb->CDB, srb->cmnd, bcb->Length);
 
 	/* send it to out endpoint */
 	US_DEBUGP("Bulk command S 0x%x T 0x%x Trg %d LUN %d L %d F %d CL %d\n",
-		  le32_to_cpu(bcb.Signature), bcb.Tag,
-		  (bcb.Lun >> 4), (bcb.Lun & 0x0F), 
-		  le32_to_cpu(bcb.DataTransferLength), bcb.Flags, bcb.Length);
+			le32_to_cpu(bcb->Signature), bcb->Tag,
+			(bcb->Lun >> 4), (bcb->Lun & 0x0F), 
+			le32_to_cpu(bcb->DataTransferLength),
+			bcb->Flags, bcb->Length);
 	result = usb_stor_bulk_transfer_buf(us, us->send_bulk_pipe,
-				&bcb, US_BULK_CB_WRAP_LEN, NULL);
+				bcb, US_BULK_CB_WRAP_LEN, NULL);
 	US_DEBUGP("Bulk command transfer result=%d\n", result);
 	if (result != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_ERROR;
@@ -972,7 +982,7 @@ int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 	/* get CSW for device status */
 	US_DEBUGP("Attempting to get CSW...\n");
 	result = usb_stor_bulk_transfer_buf(us, us->recv_bulk_pipe,
-				&bcs, US_BULK_CS_WRAP_LEN, NULL);
+				bcs, US_BULK_CS_WRAP_LEN, NULL);
 
 	/* did the attempt to read the CSW fail? */
 	if (result == USB_STOR_XFER_STALLED) {
@@ -980,7 +990,7 @@ int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 		/* get the status again */
 		US_DEBUGP("Attempting to get CSW (2nd try)...\n");
 		result = usb_stor_bulk_transfer_buf(us, us->recv_bulk_pipe,
-				&bcs, US_BULK_CS_WRAP_LEN, NULL);
+				bcs, US_BULK_CS_WRAP_LEN, NULL);
 	}
 
 	/* if we still have a failure at this point, we're in trouble */
@@ -990,17 +1000,18 @@ int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 
 	/* check bulk status */
 	US_DEBUGP("Bulk status Sig 0x%x T 0x%x R %d Stat 0x%x\n",
-		  le32_to_cpu(bcs.Signature), bcs.Tag, 
-		  bcs.Residue, bcs.Status);
-	if ((bcs.Signature != cpu_to_le32(US_BULK_CS_SIGN) && bcs.Signature != cpu_to_le32(US_BULK_CS_OLYMPUS_SIGN)) || 
-	    bcs.Tag != bcb.Tag || 
-	    bcs.Status > US_BULK_STAT_PHASE) {
+			le32_to_cpu(bcs->Signature), bcs->Tag, 
+			bcs->Residue, bcs->Status);
+	if ((bcs->Signature != cpu_to_le32(US_BULK_CS_SIGN) &&
+		    bcs->Signature != cpu_to_le32(US_BULK_CS_OLYMPUS_SIGN)) ||
+			bcs->Tag != srb->serial_number || 
+			bcs->Status > US_BULK_STAT_PHASE) {
 		US_DEBUGP("Bulk logical error\n");
 		return USB_STOR_TRANSPORT_ERROR;
 	}
 
 	/* based on the status code, we report good or bad */
-	switch (bcs.Status) {
+	switch (bcs->Status) {
 		case US_BULK_STAT_OK:
 			/* device babbled -- return fake sense data */
 			if (fake_sense) {
@@ -1065,6 +1076,10 @@ static int usb_stor_reset_common(struct us_data *us,
 	schedule_timeout(HZ*6);
 	set_current_state(TASK_RUNNING);
 	down(&us->dev_semaphore);
+	if (test_bit(US_FLIDX_DISCONNECTING, &us->flags)) {
+		US_DEBUGP("Reset interrupted by disconnect\n");
+		return FAILED;
+	}
 
 	US_DEBUGP("Soft reset: clearing bulk-in endpoint halt\n");
 	result = usb_stor_clear_halt(us, us->recv_bulk_pipe);
@@ -1083,18 +1098,18 @@ static int usb_stor_reset_common(struct us_data *us,
 
 /* This issues a CB[I] Reset to the device in question
  */
+#define CB_RESET_CMD_SIZE	12
+
 int usb_stor_CB_reset(struct us_data *us)
 {
-	unsigned char cmd[12];
-
-	US_DEBUGP("CB_reset() called\n");
+	US_DEBUGP("%s called\n", __FUNCTION__);
 
-	memset(cmd, 0xFF, sizeof(cmd));
-	cmd[0] = SEND_DIAGNOSTIC;
-	cmd[1] = 4;
+	memset(us->iobuf, 0xFF, CB_RESET_CMD_SIZE);
+	us->iobuf[0] = SEND_DIAGNOSTIC;
+	us->iobuf[1] = 4;
 	return usb_stor_reset_common(us, US_CBI_ADSC, 
 				 USB_TYPE_CLASS | USB_RECIP_INTERFACE,
-				 0, us->ifnum, cmd, sizeof(cmd));
+				 0, us->ifnum, us->iobuf, CB_RESET_CMD_SIZE);
 }
 
 /* This issues a Bulk-only Reset to the device in question, including
@@ -1102,7 +1117,7 @@ int usb_stor_CB_reset(struct us_data *us)
  */
 int usb_stor_Bulk_reset(struct us_data *us)
 {
-	US_DEBUGP("Bulk reset requested\n");
+	US_DEBUGP("%s called\n", __FUNCTION__);
 
 	return usb_stor_reset_common(us, US_BULK_RESET_REQUEST, 
 				 USB_TYPE_CLASS | USB_RECIP_INTERFACE,

drivers/usb/storage/unusual_devs.h

@@ -252,6 +252,14 @@ UNUSUAL_DEV(  0x054c, 0x0025, 0x0100, 0x0100,
 		US_SC_UFI, US_PR_CB, NULL,
 		US_FL_SINGLE_LUN ),
 
+#ifdef CONFIG_USB_STORAGE_ISD200
+UNUSUAL_DEV(  0x054c, 0x002b, 0x0100, 0x0110,
+		"Sony",
+		"Portable USB Harddrive V2",
+		US_SC_ISD200, US_PR_BULK, isd200_Initialization,
+		0 ),
+#endif
+
 UNUSUAL_DEV(  0x054c, 0x002d, 0x0100, 0x0100, 
 		"Sony",
 		"Memorystick MSAC-US1",
@@ -295,26 +303,6 @@ UNUSUAL_DEV(  0x059f, 0xa601, 0x0200, 0x0200,
 		"USB Hard Disk",
 		US_SC_RBC, US_PR_CB, NULL, 0 ), 
 
-/* This Pentax still camera is not conformant
- * to the USB storage specification: -
- * - It does not like the INQUIRY command. So we must handle this command
- *   of the SCSI layer ourselves.
- * Tested on Rev. 10.00 (0x1000)
- * Submitted by James Courtier-Dutton <James@superbug.demon.co.uk>
- */
-UNUSUAL_DEV( 0x0a17, 0x0004, 0x1000, 0x1000,
-                "Pentax",
-                "Optio 2/3/400",
-                US_SC_DEVICE, US_PR_DEVICE, NULL,
-                US_FL_FIX_INQUIRY ),
-
-/* Submitted by Per Winkvist <per.winkvist@uk.com> */
-UNUSUAL_DEV( 0x0a17, 0x006, 0x1000, 0x9009,
-                "Pentax",
-                "Optio S",
-                US_SC_8070, US_PR_CBI, NULL,
-                US_FL_FIX_INQUIRY ),
-
 #ifdef CONFIG_USB_STORAGE_ISD200
 UNUSUAL_DEV(  0x05ab, 0x0031, 0x0100, 0x0110,
 		"In-System",
@@ -339,12 +327,6 @@ UNUSUAL_DEV(  0x05ab, 0x5701, 0x0100, 0x0110,
 		"USB Storage Adapter V2",
 		US_SC_ISD200, US_PR_BULK, isd200_Initialization,
 		0 ),
-
-UNUSUAL_DEV(  0x054c, 0x002b, 0x0100, 0x0110,
-		"Sony",
-		"Portable USB Harddrive V2",
-		US_SC_ISD200, US_PR_BULK, isd200_Initialization,
-		0 ),
 #endif
 
 #ifdef CONFIG_USB_STORAGE_JUMPSHOT
@@ -385,12 +367,6 @@ UNUSUAL_DEV(  0x05e3, 0x0702, 0x0000, 0x0001,
 		US_SC_DEVICE, US_PR_DEVICE, NULL,
 		US_FL_FIX_INQUIRY ),
 
-UNUSUAL_DEV(  0x05e3, 0x0700, 0x0000, 0x9999,
-		"Unknown",
-		"GL641USB based CF Card reader",
-		US_SC_SCSI, US_PR_BULK, NULL,
-		US_FL_FIX_INQUIRY | US_FL_MODE_XLATE),
-
 /* Reported by Hanno Boeck <hanno@gmx.de>
  * Taken from the Lycoris Kernel */
 UNUSUAL_DEV(  0x0636, 0x0003, 0x0000, 0x9999,
@@ -520,13 +496,6 @@ UNUSUAL_DEV( 0x07c4, 0xa006, 0x0000, 0xffff,
 		"Simple Tech/Datafab CF+SM Reader",
 		US_SC_SCSI, US_PR_DATAFAB, NULL,
 		US_FL_MODE_XLATE ),
-
-/* Submitted by Olaf Hering <olh@suse.de> */
-UNUSUAL_DEV(  0x07c4, 0xa109, 0x0000, 0xffff,
-		"Datafab Systems, Inc.",
-		"USB to CF + SM Combo (LC1)",
-		US_SC_SCSI, US_PR_DATAFAB, NULL,
-		US_FL_MODE_XLATE ),
 #endif
 		
 #ifdef CONFIG_USB_STORAGE_SDDR55
@@ -538,6 +507,15 @@ UNUSUAL_DEV( 0x07c4, 0xa103, 0x0000, 0x9999,
 		US_FL_FIX_INQUIRY ),
 #endif
 
+#ifdef CONFIG_USB_STORAGE_DATAFAB
+/* Submitted by Olaf Hering <olh@suse.de> */
+UNUSUAL_DEV(  0x07c4, 0xa109, 0x0000, 0xffff,
+		"Datafab Systems, Inc.",
+		"USB to CF + SM Combo (LC1)",
+		US_SC_SCSI, US_PR_DATAFAB, NULL,
+		US_FL_MODE_XLATE ),
+#endif
+
 /* Datafab KECF-USB / Sagatek DCS-CF / Simpletech Flashlink UCF-100
  * Only revision 1.13 tested (same for all of the above devices,
  * based on the Datafab DF-UG-07 chip).  Needed for US_FL_FIX_INQUIRY.
@@ -563,6 +541,22 @@ UNUSUAL_DEV( 0x07cf, 0x1001, 0x1000, 0x9009,
 		US_SC_8070, US_PR_CB, NULL,
 		US_FL_FIX_INQUIRY ),
 
+/* Submitted by Hartmut Wahl <hwahl@hwahl.de>*/
+UNUSUAL_DEV( 0x0839, 0x000a, 0x0001, 0x0001,
+		"Samsung",
+		"Digimax 410",
+		US_SC_DEVICE, US_PR_DEVICE, NULL,
+		US_FL_FIX_INQUIRY),
+
+/* Aiptek PocketCAM 3Mega
+ * Nicolas DUPEUX <nicolas@dupeux.net> 
+ */
+UNUSUAL_DEV(  0x08ca, 0x2011, 0x0000, 0x9999,
+		"AIPTEK",
+		"PocketCAM 3Mega",
+		US_SC_SCSI, US_PR_BULK, NULL,
+		US_FL_MODE_XLATE ),
+
 /* aeb */
 UNUSUAL_DEV( 0x090c, 0x1132, 0x0000, 0xffff,
 		"Feiya",
@@ -570,13 +564,6 @@ UNUSUAL_DEV( 0x090c, 0x1132, 0x0000, 0xffff,
 		US_SC_SCSI, US_PR_BULK, NULL,
 		US_FL_FIX_CAPACITY ),
                 
-/* Submitted by Hartmut Wahl <hwahl@hwahl.de>*/
-UNUSUAL_DEV( 0x0839, 0x000a, 0x0001, 0x0001,
-        "Samsung",
-        "Digimax 410",
-        US_SC_SCSI, US_PR_BULK, NULL,
-        US_FL_FIX_INQUIRY),
-                
 UNUSUAL_DEV(  0x097a, 0x0001, 0x0000, 0x0001,
 		"Minds@Work",
 		"Digital Wallet",
@@ -589,21 +576,25 @@ UNUSUAL_DEV(  0x0a16, 0x8888, 0x0100, 0x0100,
 		US_SC_SCSI, US_PR_BULK, NULL,
 		US_FL_FIX_INQUIRY ),
 
-UNUSUAL_DEV(  0x0a16, 0x8888, 0x0100, 0x0100,
-		"IBM",
-		"IBM USB Memory Key",
-		US_SC_SCSI, US_PR_BULK, NULL,
+/* This Pentax still camera is not conformant
+ * to the USB storage specification: -
+ * - It does not like the INQUIRY command. So we must handle this command
+ *   of the SCSI layer ourselves.
+ * Tested on Rev. 10.00 (0x1000)
+ * Submitted by James Courtier-Dutton <James@superbug.demon.co.uk>
+ */
+UNUSUAL_DEV( 0x0a17, 0x0004, 0x1000, 0x1000,
+                "Pentax",
+                "Optio 2/3/400",
+                US_SC_DEVICE, US_PR_DEVICE, NULL,
                 US_FL_FIX_INQUIRY ),
 
-/* Pentax Optio S digital camera
- * adapted from http://www2.goldfisch.at/knowledge/233
- * (Peter Pilsl <pilsl@goldfisch.at>)
- * by Christoph Weidemann <cweidema@indiana.edu> */
-UNUSUAL_DEV(  0x0a17, 0x0006, 0x0000, 0xffff,
+/* Submitted by Per Winkvist <per.winkvist@uk.com> */
+UNUSUAL_DEV( 0x0a17, 0x006, 0x1000, 0x9009,
                 "Pentax",
                 "Optio S",
-		US_SC_8070, US_PR_CB, NULL,
-		US_FL_MODE_XLATE|US_FL_FIX_INQUIRY),
+                US_SC_8070, US_PR_CBI, NULL,
+                US_FL_FIX_INQUIRY ),
 		
 #ifdef CONFIG_USB_STORAGE_ISD200
 UNUSUAL_DEV(  0x0bf6, 0xa001, 0x0100, 0x0110,
@@ -613,13 +604,6 @@ UNUSUAL_DEV(  0x0bf6, 0xa001, 0x0100, 0x0110,
 		0 ),
 #endif
 
-/* EasyDisk support. Submitted by Stanislav Karchebny <berk@madfire.net> */
-UNUSUAL_DEV(  0x1065, 0x2136, 0x0000, 0x0001,
-		"Global Channel Solutions",
-		"EasyDisk EDxxxx",
-		US_SC_SCSI, US_PR_BULK, NULL,
-		US_FL_MODE_XLATE | US_FL_FIX_INQUIRY ),
-
 /* Reported by Kevin Cernekee <kpc-usbdev@gelato.uiuc.edu>
  * Tested on hardware version 1.10.
  * Entry is needed only for the initializer function override.
@@ -648,13 +632,3 @@ UNUSUAL_DEV(  0x55aa, 0xa103, 0x0000, 0x9999,
 		US_SC_SCSI, US_PR_SDDR55, NULL,
 		US_FL_SINGLE_LUN),
 #endif
-
-/* Aiptek PocketCAM 3Mega
- * Nicolas DUPEUX <nicolas@dupeux.net> 
- */
-UNUSUAL_DEV(  0x08ca, 0x2011, 0x0000, 0x9999,
-	"AIPTEK",
-	"PocketCAM 3Mega",
-	US_SC_SCSI, US_PR_BULK, NULL,
-	US_FL_MODE_XLATE ),
-

drivers/usb/storage/usb.c

@@ -338,10 +338,16 @@ static int usb_stor_control_thread(void * __us)
 		/* lock the device pointers */
 		down(&(us->dev_semaphore));
 
+		/* don't do anything if we are disconnecting */
+		if (test_bit(US_FLIDX_DISCONNECTING, &us->flags)) {
+			US_DEBUGP("No command during disconnect\n");
+			us->srb->result = DID_BAD_TARGET << 16;
+		}
+
 		/* reject the command if the direction indicator 
 		 * is UNKNOWN
 		 */
-		if (us->srb->sc_data_direction == SCSI_DATA_UNKNOWN) {
+		else if (us->srb->sc_data_direction == SCSI_DATA_UNKNOWN) {
 			US_DEBUGP("UNKNOWN data direction\n");
 			us->srb->result = DID_ERROR << 16;
 		}
@@ -421,12 +427,44 @@ static int usb_stor_control_thread(void * __us)
  * Device probing and disconnecting
  ***********************************************************************/
 
+/* Associate our private data with the USB device */
+static int associate_dev(struct us_data *us, struct usb_interface *intf)
+{
+	US_DEBUGP("-- %s\n", __FUNCTION__);
+
+	/* Fill in the device-related fields */
+	us->pusb_dev = interface_to_usbdev(intf);
+	us->pusb_intf = intf;
+	us->ifnum = intf->altsetting->desc.bInterfaceNumber;
+
+	/* Store our private data in the interface and increment the
+	 * device's reference count */
+	usb_set_intfdata(intf, us);
+	usb_get_dev(us->pusb_dev);
+
+	/* Allocate the device-related DMA-mapped buffers */
+	us->cr = usb_buffer_alloc(us->pusb_dev, sizeof(*us->cr),
+			GFP_KERNEL, &us->cr_dma);
+	if (!us->cr) {
+		US_DEBUGP("usb_ctrlrequest allocation failed\n");
+		return -ENOMEM;
+	}
+
+	us->iobuf = usb_buffer_alloc(us->pusb_dev, US_IOBUF_SIZE,
+			GFP_KERNEL, &us->iobuf_dma);
+	if (!us->iobuf) {
+		US_DEBUGP("I/O buffer allocation failed\n");
+		return -ENOMEM;
+	}
+	return 0;
+}
+
 /* Get the unusual_devs entries and the string descriptors */
 static void get_device_info(struct us_data *us, int id_index)
 {
 	struct usb_device *dev = us->pusb_dev;
-	struct usb_host_interface *altsetting =
-		&us->pusb_intf->altsetting[us->pusb_intf->act_altsetting];
+	struct usb_interface_descriptor *idesc =
+		&us->pusb_intf->altsetting[us->pusb_intf->act_altsetting].desc;
 	struct us_unusual_dev *unusual_dev = &us_unusual_dev_list[id_index];
 	struct usb_device_id *id = &storage_usb_ids[id_index];
 
@@ -438,10 +476,10 @@ static void get_device_info(struct us_data *us, int id_index)
 	/* Store the entries */
 	us->unusual_dev = unusual_dev;
 	us->subclass = (unusual_dev->useProtocol == US_SC_DEVICE) ?
-			altsetting->desc.bInterfaceSubClass :
+			idesc->bInterfaceSubClass :
 			unusual_dev->useProtocol;
 	us->protocol = (unusual_dev->useTransport == US_PR_DEVICE) ?
-			altsetting->desc.bInterfaceProtocol :
+			idesc->bInterfaceProtocol :
 			unusual_dev->useTransport;
 	us->flags = unusual_dev->flags;
 
@@ -455,20 +493,26 @@ static void get_device_info(struct us_data *us, int id_index)
 			"an unneeded SubClass entry",
 			"an unneeded Protocol entry",
 			"unneeded SubClass and Protocol entries"};
+		struct usb_device_descriptor *ddesc = &dev->descriptor;
 		int msg = -1;
 
 		if (unusual_dev->useProtocol != US_SC_DEVICE &&
-			us->subclass == altsetting->desc.bInterfaceSubClass)
+			us->subclass == idesc->bInterfaceSubClass)
 			msg += 1;
 		if (unusual_dev->useTransport != US_PR_DEVICE &&
-			us->protocol == altsetting->desc.bInterfaceProtocol)
+			us->protocol == idesc->bInterfaceProtocol)
 			msg += 2;
 		if (msg >= 0)
 			printk(KERN_NOTICE USB_STORAGE "This device "
-				"(%04x,%04x) has %s in unusual_devs.h\n"
+				"(%04x,%04x,%04x S %02x P %02x)"
+				" has %s in unusual_devs.h\n"
 				"   Please send a copy of this message to "
 				"<linux-usb-devel@lists.sourceforge.net>\n",
-				id->idVendor, id->idProduct, msgs[msg]);
+				ddesc->idVendor, ddesc->idProduct,
+				ddesc->bcdDevice,
+				idesc->bInterfaceSubClass,
+				idesc->bInterfaceProtocol,
+				msgs[msg]);
 	}
 
 	/* Read the device's string descriptors */
@@ -485,15 +529,15 @@ static void get_device_info(struct us_data *us, int id_index)
 	/* Use the unusual_dev strings if the device didn't provide them */
 	if (strlen(us->vendor) == 0) {
 		if (unusual_dev->vendorName)
-			strncpy(us->vendor, unusual_dev->vendorName,
-				sizeof(us->vendor) - 1);
+			strlcpy(us->vendor, unusual_dev->vendorName,
+				sizeof(us->vendor));
 		else
 			strcpy(us->vendor, "Unknown");
 	}
 	if (strlen(us->product) == 0) {
 		if (unusual_dev->productName)
-			strncpy(us->product, unusual_dev->productName,
-				sizeof(us->product) - 1);
+			strlcpy(us->product, unusual_dev->productName,
+				sizeof(us->product));
 		else
 			strcpy(us->product, "Unknown");
 	}
@@ -714,18 +758,9 @@ static int usb_stor_acquire_resources(struct us_data *us)
 {
 	int p;
 
-	/* Allocate the USB control blocks */
-	US_DEBUGP("Allocating usb_ctrlrequest\n");
-	us->dr = kmalloc(sizeof(*us->dr), GFP_KERNEL);
-	if (!us->dr) {
-		US_DEBUGP("allocation failed\n");
-		return -ENOMEM;
-	}
-
-	US_DEBUGP("Allocating URB\n");
 	us->current_urb = usb_alloc_urb(0, GFP_KERNEL);
 	if (!us->current_urb) {
-		US_DEBUGP("allocation failed\n");
+		US_DEBUGP("URB allocation failed\n");
 		return -ENOMEM;
 	}
 
@@ -778,8 +813,24 @@ static void dissociate_dev(struct us_data *us)
 {
 	US_DEBUGP("-- %s\n", __FUNCTION__);
 	down(&us->dev_semaphore);
+
+	/* Free the device-related DMA-mapped buffers */
+	if (us->cr) {
+		usb_buffer_free(us->pusb_dev, sizeof(*us->cr), us->cr,
+				us->cr_dma);
+		us->cr = NULL;
+	}
+	if (us->iobuf) {
+		usb_buffer_free(us->pusb_dev, US_IOBUF_SIZE, us->iobuf,
+				us->iobuf_dma);
+		us->iobuf = NULL;
+	}
+
+	/* Remove our private data from the interface and decrement the
+	 * device's reference count */
 	usb_set_intfdata(us->pusb_intf, NULL);
 	usb_put_dev(us->pusb_dev);
+
 	us->pusb_dev = NULL;
 	us->pusb_intf = NULL;
 	up(&us->dev_semaphore);
@@ -818,16 +869,11 @@ void usb_stor_release_resources(struct us_data *us)
 		us->extra_destructor(us->extra);
 	}
 
-	/* Destroy the extra data */
-	if (us->extra) {
+	/* Free the extra data and the URB */
+	if (us->extra)
 		kfree(us->extra);
-	}
-
-	/* Free the USB control blocks */
 	if (us->current_urb)
 		usb_free_urb(us->current_urb);
-	if (us->dr)
-		kfree(us->dr);
 
 	/* Free the structure itself */
 	kfree(us);
@@ -857,15 +903,10 @@ static int storage_probe(struct usb_interface *intf,
 	init_MUTEX_LOCKED(&(us->sema));
 	init_completion(&(us->notify));
 
-	/* Fill in the device-related fields */
-	us->pusb_dev = interface_to_usbdev(intf);
-	us->pusb_intf = intf;
-	us->ifnum = intf->altsetting->desc.bInterfaceNumber;
-
-	/* Store our private data in the interface and increment the
-	 * device's reference count */
-	usb_set_intfdata(intf, us);
-	usb_get_dev(us->pusb_dev);
+	/* Associate the us_data structure with the USB device */
+	result = associate_dev(us, intf);
+	if (result)
+		goto BadDevice;
 
 	/*
 	 * Get the unusual_devs entries and the descriptors

drivers/usb/storage/usb.h

@@ -92,6 +92,15 @@ struct us_unusual_dev {
 
 #define USB_STOR_STRING_LEN 32
 
+/*
+ * We provide a DMA-mapped I/O buffer for use with small USB transfers.
+ * It turns out that CB[I] needs a 12-byte buffer and Bulk-only needs a
+ * 31-byte buffer.  But Freecom needs a 64-byte buffer, so that's the
+ * size we'll allocate.
+ */
+
+#define US_IOBUF_SIZE		64	/* Size of the DMA-mapped I/O buffer */
+
 typedef int (*trans_cmnd)(Scsi_Cmnd*, struct us_data*);
 typedef int (*trans_reset)(struct us_data*);
 typedef void (*proto_cmnd)(Scsi_Cmnd*, struct us_data*);
@@ -106,6 +115,7 @@ struct us_data {
 	struct semaphore	dev_semaphore;	 /* protect pusb_dev */
 	struct usb_device	*pusb_dev;	 /* this usb_device */
 	struct usb_interface	*pusb_intf;	 /* this interface */
+	struct us_unusual_dev   *unusual_dev;	 /* device-filter entry     */
 	unsigned long		flags;		 /* from filter initially */
 	unsigned int		send_bulk_pipe;	 /* cached pipe values */
 	unsigned int		recv_bulk_pipe;
@@ -139,20 +149,19 @@ struct us_data {
 	int			pid;		 /* control thread	 */
 	int			sm_state;	 /* what we are doing	 */
 
-	/* interrupt communications data */
-	unsigned char		irqdata[2];	 /* data from USB IRQ	 */
-
 	/* control and bulk communications data */
-	struct urb		*current_urb;	 /* non-int USB requests */
-	struct usb_ctrlrequest	*dr;		 /* control requests	 */
-	struct usb_sg_request	current_sg;	 /* scatter-gather USB   */
-
-	/* the semaphore for sleeping the control thread */
-	struct semaphore	sema;		 /* to sleep thread on   */
+	struct urb		*current_urb;	 /* USB requests	 */
+	struct usb_ctrlrequest	*cr;		 /* control requests	 */
+	struct usb_sg_request	current_sg;	 /* scatter-gather req.  */
+	unsigned char		*iobuf;		 /* I/O buffer		 */
+	dma_addr_t		cr_dma;		 /* buffer DMA addresses */
+	dma_addr_t		iobuf_dma;
 
 	/* mutual exclusion structures */
+	struct semaphore	sema;		 /* to sleep thread on   */
 	struct completion	notify;		 /* thread begin/end	    */
-	struct us_unusual_dev   *unusual_dev;	 /* If unusual device       */
+
+	/* subdriver information */
 	void			*extra;		 /* Any extra data          */
 	extra_data_destructor	extra_destructor;/* extra data destructor   */
 };