Commit 194303d6 authored by Amelie Delaunay's avatar Amelie Delaunay Committed by Kishon Vijay Abraham I

dt-bindings: phy: add support for STM32 USB PHY Controller (USBPHYC)

This patch adds the device tree bindings description for STM32 USBPHYC
(USB PHY Controller).
Signed-off-by: default avatarAmelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: default avatarRob Herring <robh@kernel.org>
Signed-off-by: default avatarKishon Vijay Abraham I <kishon@ti.com>
parent bb0e500b
STMicroelectronics STM32 USB HS PHY controller
The STM32 USBPHYC block contains a dual port High Speed UTMI+ PHY and a UTMI
switch. It controls PHY configuration and status, and the UTMI+ switch that
selects either OTG or HOST controller for the second PHY port. It also sets
PLL configuration.
USBPHYC
|_ PLL
|
|_ PHY port#1 _________________ HOST controller
| _ |
| / 1|________________|
|_ PHY port#2 ----| |________________
| \_0| |
|_ UTMI switch_______| OTG controller
Phy provider node
=================
Required properties:
- compatible: must be "st,stm32mp1-usbphyc"
- reg: address and length of the usb phy control register set
- clocks: phandle + clock specifier for the PLL phy clock
- #address-cells: number of address cells for phys sub-nodes, must be <1>
- #size-cells: number of size cells for phys sub-nodes, must be <0>
Optional properties:
- assigned-clocks: phandle + clock specifier for the PLL phy clock
- assigned-clock-parents: the PLL phy clock parent
- resets: phandle + reset specifier
Required nodes: one sub-node per port the controller provides.
Phy sub-nodes
==============
Required properties:
- reg: phy port index
- phy-supply: phandle to the regulator providing 3V3 power to the PHY,
see phy-bindings.txt in the same directory.
- vdda1v1-supply: phandle to the regulator providing 1V1 power to the PHY
- vdda1v8-supply: phandle to the regulator providing 1V8 power to the PHY
- #phy-cells: see phy-bindings.txt in the same directory, must be <0> for PHY
port#1 and must be <1> for PHY port#2, to select USB controller
Example:
usbphyc: usb-phy@5a006000 {
compatible = "st,stm32mp1-usbphyc";
reg = <0x5a006000 0x1000>;
clocks = <&rcc_clk USBPHY_K>;
resets = <&rcc_rst USBPHY_R>;
#address-cells = <1>;
#size-cells = <0>;
usbphyc_port0: usb-phy@0 {
reg = <0>;
phy-supply = <&vdd_usb>;
vdda1v1-supply = <&reg11>;
vdda1v8-supply = <&reg18>
#phy-cells = <0>;
};
usbphyc_port1: usb-phy@1 {
reg = <1>;
phy-supply = <&vdd_usb>;
vdda1v1-supply = <&reg11>;
vdda1v8-supply = <&reg18>
#phy-cells = <1>;
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment