Merge branch 'fixes-non-critical' into next/drivers2

fixes-non-critical has already been merged upstream, and there are a
handful of annoying context conflicts that it makes sense to resolve
before sending up. Part of this is because there was parallel development
going on between more urgent fixes and general driver fixups, it should
settle down once the lpc32xx platform reaches a more steady state.

Conflicts:
	arch/arm/mach-lpc32xx/clock.c
	arch/arm/mach-lpc32xx/common.h
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/Kconfig

@@ -901,6 +901,7 @@ config ARCH_U300
 
 config ARCH_U8500
 	bool "ST-Ericsson U8500 Series"
+	depends on MMU
 	select CPU_V7
 	select ARM_AMBA
 	select GENERIC_CLOCKEVENTS
@@ -1577,7 +1578,7 @@ config LOCAL_TIMERS
 config ARCH_NR_GPIO
 	int
 	default 1024 if ARCH_SHMOBILE || ARCH_TEGRA
-	default 350 if ARCH_U8500
+	default 355 if ARCH_U8500
 	default 0
 	help
 	  Maximum number of GPIOs in the system.

arch/arm/configs/imx_v4_v5_defconfig

@@ -69,6 +69,7 @@ CONFIG_MTD_CFI=y
 CONFIG_MTD_CFI_ADV_OPTIONS=y
 CONFIG_MTD_CFI_GEOMETRY=y
 # CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
 # CONFIG_MTD_CFI_I2 is not set
 CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_MTD_PHYSMAP=y

arch/arm/mach-davinci/cpufreq.c

@@ -95,7 +95,7 @@ static int davinci_target(struct cpufreq_policy *policy,
 	if (freqs.old == freqs.new)
 		return ret;
 
-	dev_dbg(&cpufreq.dev, "transition: %u --> %u\n", freqs.old, freqs.new);
+	dev_dbg(cpufreq.dev, "transition: %u --> %u\n", freqs.old, freqs.new);
 
 	ret = cpufreq_frequency_table_target(policy, pdata->freq_table,
 						freqs.new, relation, &idx);

arch/arm/mach-davinci/da850.c

@@ -1026,7 +1026,7 @@ static int da850_round_armrate(struct clk *clk, unsigned long rate)
 }
 #endif
 
-int da850_register_pm(struct platform_device *pdev)
+int __init da850_register_pm(struct platform_device *pdev)
 {
 	int ret;
 	struct davinci_pm_config *pdata = pdev->dev.platform_data;

arch/arm/mach-davinci/dma.c

@@ -1508,12 +1508,8 @@ static int __init edma_probe(struct platform_device *pdev)
 			goto fail;
 		}
 
-		/* Everything lives on transfer controller 1 until otherwise
-		 * specified. This way, long transfers on the low priority queue
-		 * started by the codec engine will not cause audio defects.
-		 */
 		for (i = 0; i < edma_cc[j]->num_channels; i++)
-			map_dmach_queue(j, i, EVENTQ_1);
+			map_dmach_queue(j, i, info[j]->default_queue);
 
 		queue_tc_mapping = info[j]->queue_tc_mapping;
 		queue_priority_mapping = info[j]->queue_priority_mapping;

arch/arm/mach-davinci/include/mach/edma.h

@@ -250,6 +250,11 @@ struct edma_soc_info {
 	unsigned	n_slot;
 	unsigned	n_tc;
 	unsigned	n_cc;
+	/*
+	 * Default queue is expected to be a low-priority queue.
+	 * This way, long transfers on the default queue started
+	 * by the codec engine will not cause audio defects.
+	 */
 	enum dma_event_q	default_queue;
 
 	/* Resource reservation for other cores */

arch/arm/mach-imx/mach-pcm038.c

@@ -233,7 +233,7 @@ static struct regulator_init_data sdhc1_data = {
 
 static struct regulator_consumer_supply cam_consumers[] = {
 	{
-		.dev	= NULL,
+		.dev_name = NULL,
 		.supply	= "imx_cam_vcc",
 	},
 };

arch/arm/mach-imx/mm-imx3.c

@@ -76,7 +76,7 @@ static void __iomem *imx3_ioremap(unsigned long phys_addr, size_t size,
 	return __arm_ioremap(phys_addr, size, mtype);
 }
 
-void imx3_init_l2x0(void)
+void __init imx3_init_l2x0(void)
 {
 	void __iomem *l2x0_base;
 	void __iomem *clkctl_base;

arch/arm/mach-lpc32xx/clock.c

@@ -1129,12 +1129,12 @@ static struct clk_lookup lookups[] = {
 	_REGISTER_CLOCK("dev:ssp1", NULL, clk_ssp1)
 	_REGISTER_CLOCK("lpc32xx_keys.0", NULL, clk_kscan)
 	_REGISTER_CLOCK("lpc32xx-nand.0", "nand_ck", clk_nand)
+	_REGISTER_CLOCK("lpc32xx-adc", NULL, clk_adc)
 	_REGISTER_CLOCK(NULL, "i2s0_ck", clk_i2s0)
 	_REGISTER_CLOCK(NULL, "i2s1_ck", clk_i2s1)
-	_REGISTER_CLOCK("lpc32xx-adc", NULL, clk_adc)
 	_REGISTER_CLOCK("ts-lpc32xx", NULL, clk_tsc)
 	_REGISTER_CLOCK("dev:mmc0", NULL, clk_mmc)
-	_REGISTER_CLOCK("lpc-eth.0", NULL, clk_net)
+	_REGISTER_CLOCK("lpc-net.0", NULL, clk_net)
 	_REGISTER_CLOCK("dev:clcd", NULL, clk_lcd)
 	_REGISTER_CLOCK("lpc32xx_udc", "ck_usbd", clk_usbd)
 	_REGISTER_CLOCK("lpc32xx_rtc", NULL, clk_rtc)

arch/arm/mach-lpc32xx/common.h

@@ -69,6 +69,7 @@ extern u32 clk_get_pclk_div(void);
  */
 extern void lpc32xx_get_uid(u32 devid[4]);
 
+extern u32 lpc32xx_return_iram_size(void);
 /*
  * Pointers used for sizing and copying suspend function data
  */

arch/arm/mach-omap1/io.c

@@ -118,7 +118,7 @@ void __init omap16xx_map_io(void)
 /*
  * Common low-level hardware init for omap1.
  */
-void omap1_init_early(void)
+void __init omap1_init_early(void)
 {
 	omap_check_revision();
 

arch/arm/mach-omap1/lcd_dma.c

@@ -117,7 +117,7 @@ EXPORT_SYMBOL(omap_set_lcd_dma_b1_mirror);
 void omap_set_lcd_dma_b1_vxres(unsigned long vxres)
 {
 	if (cpu_is_omap15xx()) {
-		printk(KERN_ERR "DMA virtual resulotion is not supported "
+		printk(KERN_ERR "DMA virtual resolution is not supported "
 				"in 1510 mode\n");
 		BUG();
 	}

arch/arm/mach-omap2/Makefile

@@ -265,6 +265,8 @@ obj-y					+= $(smc91x-m) $(smc91x-y)
 
 smsc911x-$(CONFIG_SMSC911X)		:= gpmc-smsc911x.o
 obj-y					+= $(smsc911x-m) $(smsc911x-y)
-obj-$(CONFIG_ARCH_OMAP4)		+= hwspinlock.o
+ifneq ($(CONFIG_HWSPINLOCK_OMAP),)
+obj-y					+= hwspinlock.o
+endif
 
 obj-y					+= common-board-devices.o twl-common.o

arch/arm/mach-omap2/board-2430sdp.c

@@ -279,7 +279,7 @@ static void __init omap_2430sdp_init(void)
 	platform_add_devices(sdp2430_devices, ARRAY_SIZE(sdp2430_devices));
 	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
-	omap2_hsmmc_init(mmc);
+	omap_hsmmc_init(mmc);
 	omap2_usbfs_init(&sdp2430_usb_config);
 
 	omap_mux_init_signal("usb0hs_stp", OMAP_PULL_ENA | OMAP_PULL_UP);

arch/arm/mach-omap2/board-3430sdp.c

@@ -232,11 +232,13 @@ static struct omap2_hsmmc_info mmc[] = {
 		 */
 		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 4,
+		.deferred	= true,
 	},
 	{
 		.mmc		= 2,
 		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 7,
+		.deferred	= true,
 	},
 	{}	/* Terminator */
 };
@@ -249,7 +251,7 @@ static int sdp3430_twl_gpio_setup(struct device *dev,
 	 */
 	mmc[0].gpio_cd = gpio + 0;
 	mmc[1].gpio_cd = gpio + 1;
-	omap2_hsmmc_init(mmc);
+	omap_hsmmc_late_init(mmc);
 
 	/* gpio + 7 is "sub_lcd_en_bkl" (output/PWM1) */
 	gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "sub_lcd_en_bkl");
@@ -606,6 +608,7 @@ static void __init omap_3430sdp_init(void)
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 	omap_board_config = sdp3430_config;
 	omap_board_config_size = ARRAY_SIZE(sdp3430_config);
+	omap_hsmmc_init(mmc);
 	omap3430_i2c_init();
 	omap_display_init(&sdp3430_dss_data);
 	if (omap_rev() > OMAP3430_REV_ES1_0)

arch/arm/mach-omap2/board-4430sdp.c

@@ -491,9 +491,9 @@ static int __init omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers)
 {
 	struct omap2_hsmmc_info *c;
 
-	omap2_hsmmc_init(controllers);
+	omap_hsmmc_init(controllers);
 	for (c = controllers; c->mmc; c++)
-		omap4_twl6030_hsmmc_set_late_init(c->dev);
+		omap4_twl6030_hsmmc_set_late_init(&c->pdev->dev);
 
 	return 0;
 }

arch/arm/mach-omap2/board-am3517evm.c

@@ -504,7 +504,7 @@ static void __init am3517_evm_init(void)
 	am3517_evm_musb_init();
 
 	/* MMC init function */
-	omap2_hsmmc_init(mmc);
+	omap_hsmmc_init(mmc);
 }
 
 MACHINE_START(OMAP3517EVM, "OMAP3517/AM3517 EVM")

arch/arm/mach-omap2/board-cm-t35.c

@@ -413,7 +413,7 @@ static struct omap2_hsmmc_info mmc[] = {
 		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
-
+		.deferred	= true,
 	},
 	{
 		.mmc		= 2,
@@ -471,7 +471,7 @@ static int cm_t35_twl_gpio_setup(struct device *dev, unsigned gpio,
 
 	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
 	mmc[0].gpio_cd = gpio + 0;
-	omap2_hsmmc_init(mmc);
+	omap_hsmmc_late_init(mmc);
 
 	return 0;
 }
@@ -639,6 +639,7 @@ static void __init cm_t3x_common_init(void)
 	omap_serial_init();
 	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
 			     mt46h32m32lf6_sdrc_params);
+	omap_hsmmc_init(mmc);
 	cm_t35_init_i2c();
 	omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL);
 	cm_t35_init_ethernet();

arch/arm/mach-omap2/board-devkit8000.c

@@ -100,6 +100,7 @@ static struct omap2_hsmmc_info mmc[] = {
 		.mmc		= 1,
 		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 29,
+		.deferred	= true,
 	},
 	{}	/* Terminator */
 };
@@ -228,7 +229,7 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
 
 	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
 	mmc[0].gpio_cd = gpio + 0;
-	omap2_hsmmc_init(mmc);
+	omap_hsmmc_late_init(mmc);
 
 	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
 	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
@@ -636,6 +637,7 @@ static void __init devkit8000_init(void)
 
 	omap_dm9000_init();
 
+	omap_hsmmc_init(mmc);
 	devkit8000_i2c_init();
 	platform_add_devices(devkit8000_devices,
 			ARRAY_SIZE(devkit8000_devices));

arch/arm/mach-omap2/board-flash.c

@@ -189,7 +189,7 @@ static u8 get_gpmc0_type(void)
  *
  * @return - void.
  */
-void board_flash_init(struct flash_partitions partition_info[],
+void __init board_flash_init(struct flash_partitions partition_info[],
 			char chip_sel_board[][GPMC_CS_NUM], int nand_type)
 {
 	u8		cs = 0;

arch/arm/mach-omap2/board-igep0020.c

@@ -295,6 +295,7 @@ static struct omap2_hsmmc_info mmc[] = {
 		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
+		.deferred	= true,
 	},
 #if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
 	{
@@ -402,7 +403,7 @@ static int igep_twl_gpio_setup(struct device *dev,
 
 	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
 	mmc[0].gpio_cd = gpio + 0;
-	omap2_hsmmc_init(mmc);
+	omap_hsmmc_late_init(mmc);
 
 	/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
 #if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE)
@@ -639,6 +640,9 @@ static void __init igep_init(void)
 
 	/* Get IGEP2 hardware revision */
 	igep2_get_revision();
+
+	omap_hsmmc_init(mmc);
+
 	/* Register I2C busses and drivers */
 	igep_i2c_init();
 	platform_add_devices(igep_devices, ARRAY_SIZE(igep_devices));

arch/arm/mach-omap2/board-ldp.c

@@ -27,7 +27,6 @@
 #include <linux/io.h>
 #include <linux/smsc911x.h>
 #include <linux/mmc/host.h>
-#include <linux/gpio.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -424,7 +423,7 @@ static void __init omap_ldp_init(void)
 	board_nand_init(ldp_nand_partitions,
 		ARRAY_SIZE(ldp_nand_partitions), ZOOM_NAND_CS, 0);
 
-	omap2_hsmmc_init(mmc);
+	omap_hsmmc_init(mmc);
 	ldp_display_init();
 }
 

arch/arm/mach-omap2/board-n8x0.c

@@ -36,10 +36,6 @@
 
 #include "mux.h"
 
-static int slot1_cover_open;
-static int slot2_cover_open;
-static struct device *mmc_device;
-
 #define TUSB6010_ASYNC_CS	1
 #define TUSB6010_SYNC_CS	4
 #define TUSB6010_GPIO_INT	58
@@ -211,6 +207,10 @@ static struct omap_onenand_platform_data board_onenand_data[] = {
 #define N810_EMMC_VSD_GPIO	23
 #define N810_EMMC_VIO_GPIO	9
 
+static int slot1_cover_open;
+static int slot2_cover_open;
+static struct device *mmc_device;
+
 static int n8x0_mmc_switch_slot(struct device *dev, int slot)
 {
 #ifdef CONFIG_MMC_DEBUG

arch/arm/mach-omap2/board-omap3beagle.c

@@ -253,6 +253,7 @@ static struct omap2_hsmmc_info mmc[] = {
 		.mmc		= 1,
 		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= -EINVAL,
+		.deferred	= true,
 	},
 	{}	/* Terminator */
 };
@@ -272,12 +273,10 @@ static int beagle_twl_gpio_setup(struct device *dev,
 {
 	int r;
 
-	if (beagle_config.mmc1_gpio_wp != -EINVAL)
-		omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
 	mmc[0].gpio_wp = beagle_config.mmc1_gpio_wp;
 	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
 	mmc[0].gpio_cd = gpio + 0;
-	omap2_hsmmc_init(mmc);
+	omap_hsmmc_late_init(mmc);
 
 	/*
 	 * TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
@@ -521,6 +520,11 @@ static void __init omap3_beagle_init(void)
 {
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 	omap3_beagle_init_rev();
+
+	if (beagle_config.mmc1_gpio_wp != -EINVAL)
+		omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
+	omap_hsmmc_init(mmc);
+
 	omap3_beagle_i2c_init();
 
 	gpio_buttons[0].gpio = beagle_config.usr_button_gpio;

arch/arm/mach-omap2/board-omap3evm.c

@@ -317,6 +317,7 @@ static struct omap2_hsmmc_info mmc[] = {
 		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= 63,
+		.deferred	= true,
 	},
 #ifdef CONFIG_WL12XX_PLATFORM_DATA
 	{
@@ -361,9 +362,8 @@ static int omap3evm_twl_gpio_setup(struct device *dev,
 	int r, lcd_bl_en;
 
 	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	omap_mux_init_gpio(63, OMAP_PIN_INPUT);
 	mmc[0].gpio_cd = gpio + 0;
-	omap2_hsmmc_init(mmc);
+	omap_hsmmc_late_init(mmc);
 
 	/*
 	 * Most GPIOs are for USB OTG.  Some are mostly sent to
@@ -644,6 +644,9 @@ static void __init omap3_evm_init(void)
 	omap_board_config = omap3_evm_config;
 	omap_board_config_size = ARRAY_SIZE(omap3_evm_config);
 
+	omap_mux_init_gpio(63, OMAP_PIN_INPUT);
+	omap_hsmmc_init(mmc);
+
 	omap3_evm_i2c_init();
 
 	omap_display_init(&omap3_evm_dss_data);

arch/arm/mach-omap2/board-omap3logic.c

@@ -128,7 +128,7 @@ static void __init board_mmc_init(void)
 		return;
 	}
 
-	omap2_hsmmc_init(board_mmc_info);
+	omap_hsmmc_init(board_mmc_info);
 }
 
 static struct omap_smsc911x_platform_data __initdata board_smsc911x_data = {

arch/arm/mach-omap2/board-omap3pandora.c

@@ -273,6 +273,7 @@ static struct omap2_hsmmc_info omap3pandora_mmc[] = {
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= 126,
 		.ext_clock	= 0,
+		.deferred	= true,
 	},
 	{
 		.mmc		= 2,
@@ -281,6 +282,7 @@ static struct omap2_hsmmc_info omap3pandora_mmc[] = {
 		.gpio_wp	= 127,
 		.ext_clock	= 1,
 		.transceiver	= true,
+		.deferred	= true,
 	},
 	{
 		.mmc		= 3,
@@ -300,7 +302,7 @@ static int omap3pandora_twl_gpio_setup(struct device *dev,
 	/* gpio + {0,1} is "mmc{0,1}_cd" (input/IRQ) */
 	omap3pandora_mmc[0].gpio_cd = gpio + 0;
 	omap3pandora_mmc[1].gpio_cd = gpio + 1;
-	omap2_hsmmc_init(omap3pandora_mmc);
+	omap_hsmmc_late_init(omap3pandora_mmc);
 
 	/* gpio + 13 drives 32kHz buffer for wifi module */
 	gpio_32khz = gpio + 13;
@@ -343,7 +345,7 @@ static struct regulator_consumer_supply pandora_vcc_lcd_supply[] = {
 };
 
 static struct regulator_consumer_supply pandora_usb_phy_supply[] = {
-	REGULATOR_SUPPLY("hsusb0", "ehci-omap.0"),
+	REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"),
 };
 
 /* ads7846 on SPI and 2 nub controllers on I2C */
@@ -561,13 +563,13 @@ static struct platform_device *omap3pandora_devices[] __initdata = {
 
 static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
 
-	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
+	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
 	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
 
 	.phy_reset  = true,
-	.reset_gpio_port[0]  = 16,
-	.reset_gpio_port[1]  = -EINVAL,
+	.reset_gpio_port[0]  = -EINVAL,
+	.reset_gpio_port[1]  = 16,
 	.reset_gpio_port[2]  = -EINVAL
 };
 
@@ -580,6 +582,7 @@ static struct omap_board_mux board_mux[] __initdata = {
 static void __init omap3pandora_init(void)
 {
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
+	omap_hsmmc_init(omap3pandora_mmc);
 	omap3pandora_i2c_init();
 	pandora_wl1251_init();
 	platform_add_devices(omap3pandora_devices,

arch/arm/mach-omap2/board-omap3stalker.c

@@ -213,6 +213,7 @@ static struct omap2_hsmmc_info mmc[] = {
 		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= 23,
+		.deferred	= true,
 	 },
 	{}			/* Terminator */
 };
@@ -282,9 +283,8 @@ omap3stalker_twl_gpio_setup(struct device *dev,
 			    unsigned gpio, unsigned ngpio)
 {
 	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	omap_mux_init_gpio(23, OMAP_PIN_INPUT);
 	mmc[0].gpio_cd = gpio + 0;
-	omap2_hsmmc_init(mmc);
+	omap_hsmmc_late_init(mmc);
 
 	/*
 	 * Most GPIOs are for USB OTG.  Some are mostly sent to
@@ -425,6 +425,9 @@ static void __init omap3_stalker_init(void)
 	omap_board_config = omap3_stalker_config;
 	omap_board_config_size = ARRAY_SIZE(omap3_stalker_config);
 
+	omap_mux_init_gpio(23, OMAP_PIN_INPUT);
+	omap_hsmmc_init(mmc);
+
 	omap3_stalker_i2c_init();
 
 	platform_add_devices(omap3_stalker_devices,

arch/arm/mach-omap2/board-omap3touchbook.c

@@ -100,6 +100,7 @@ static struct omap2_hsmmc_info mmc[] = {
 		.mmc		= 1,
 		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 29,
+		.deferred	= true,
 	},
 	{}	/* Terminator */
 };
@@ -117,15 +118,9 @@ static struct gpio_led gpio_leds[];
 static int touchbook_twl_gpio_setup(struct device *dev,
 		unsigned gpio, unsigned ngpio)
 {
-	if (system_rev >= 0x20 && system_rev <= 0x34301000) {
-		omap_mux_init_gpio(23, OMAP_PIN_INPUT);
-		mmc[0].gpio_wp = 23;
-	} else {
-		omap_mux_init_gpio(29, OMAP_PIN_INPUT);
-	}
 	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
 	mmc[0].gpio_cd = gpio + 0;
-	omap2_hsmmc_init(mmc);
+	omap_hsmmc_late_init(mmc);
 
 	/* REVISIT: need ehci-omap hooks for external VBUS
 	 * power switch and overcurrent detect
@@ -351,6 +346,14 @@ static void __init omap3_touchbook_init(void)
 
 	pm_power_off = omap3_touchbook_poweroff;
 
+	if (system_rev >= 0x20 && system_rev <= 0x34301000) {
+		omap_mux_init_gpio(23, OMAP_PIN_INPUT);
+		mmc[0].gpio_wp = 23;
+	} else {
+		omap_mux_init_gpio(29, OMAP_PIN_INPUT);
+	}
+	omap_hsmmc_init(mmc);
+
 	omap3_touchbook_i2c_init();
 	platform_add_devices(omap3_touchbook_devices,
 			ARRAY_SIZE(omap3_touchbook_devices));

arch/arm/mach-omap2/board-omap4panda.c

@@ -245,9 +245,9 @@ static int __init omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers)
 {
 	struct omap2_hsmmc_info *c;
 
-	omap2_hsmmc_init(controllers);
+	omap_hsmmc_init(controllers);
 	for (c = controllers; c->mmc; c++)
-		omap4_twl6030_hsmmc_set_late_init(c->dev);
+		omap4_twl6030_hsmmc_set_late_init(&c->pdev->dev);
 
 	return 0;
 }
@@ -461,7 +461,7 @@ static struct omap_dss_board_info omap4_panda_dss_data = {
 	.default_device	= &omap4_panda_dvi_device,
 };
 
-void omap4_panda_display_init(void)
+void __init omap4_panda_display_init(void)
 {
 	int r;
 

arch/arm/mach-omap2/board-overo.c

@@ -407,8 +407,6 @@ static inline void __init overo_init_keys(void) { return; }
 static int overo_twl_gpio_setup(struct device *dev,
 		unsigned gpio, unsigned ngpio)
 {
-	omap2_hsmmc_init(mmc);
-
 #if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
 	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
 	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
@@ -505,6 +503,7 @@ static void __init overo_init(void)
 	int ret;
 
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
+	omap_hsmmc_init(mmc);
 	overo_i2c_init();
 	omap_display_init(&overo_dss_data);
 	omap_serial_init();

arch/arm/mach-omap2/board-rm680.c

@@ -120,7 +120,7 @@ static void __init rm680_peripherals_init(void)
 				ARRAY_SIZE(rm680_peripherals_devices));
 	rm680_i2c_init();
 	gpmc_onenand_init(board_onenand_data);
-	omap2_hsmmc_init(mmc);
+	omap_hsmmc_init(mmc);
 }
 
 #ifdef CONFIG_OMAP_MUX

arch/arm/mach-omap2/board-rx51-peripherals.c

@@ -1145,7 +1145,7 @@ void __init rx51_peripherals_init(void)
 
 	partition = omap_mux_get("core");
 	if (partition)
-		omap2_hsmmc_init(mmc);
+		omap_hsmmc_init(mmc);
 
 	rx51_charger_init();
 }

arch/arm/mach-omap2/board-zoom-peripherals.c

@@ -205,6 +205,7 @@ static struct omap2_hsmmc_info mmc[] = {
 		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_wp	= -EINVAL,
 		.power_saving	= true,
+		.deferred	= true,
 	},
 	{
 		.name		= "internal",
@@ -233,7 +234,7 @@ static int zoom_twl_gpio_setup(struct device *dev,
 
 	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
 	mmc[0].gpio_cd = gpio + 0;
-	omap2_hsmmc_init(mmc);
+	omap_hsmmc_late_init(mmc);
 
 	ret = gpio_request_one(LCD_PANEL_ENABLE_GPIO, GPIOF_OUT_INIT_LOW,
 			       "lcd enable");
@@ -301,6 +302,7 @@ void __init zoom_peripherals_init(void)
 	if (ret)
 		pr_err("error setting wl12xx data: %d\n", ret);
 
+	omap_hsmmc_init(mmc);
 	omap_i2c_init();
 	platform_device_register(&omap_vwlan_device);
 	usb_musb_init(NULL);

arch/arm/mach-omap2/clkt_clksel.c

@@ -43,6 +43,7 @@
 #include <linux/errno.h>
 #include <linux/clk.h>
 #include <linux/io.h>
+#include <linux/bug.h>
 
 #include <plat/clock.h>
 

arch/arm/mach-omap2/common-board-devices.c

@@ -76,13 +76,15 @@ void __init omap_ads7846_init(int bus_num, int gpio_pendown, int gpio_debounce,
 			gpio_set_debounce(gpio_pendown, gpio_debounce);
 	}
 
-	ads7846_config.gpio_pendown = gpio_pendown;
-
 	spi_bi->bus_num	= bus_num;
 	spi_bi->irq	= OMAP_GPIO_IRQ(gpio_pendown);
 
-	if (board_pdata)
+	if (board_pdata) {
+		board_pdata->gpio_pendown = gpio_pendown;
 		spi_bi->platform_data = board_pdata;
+	} else {
+		ads7846_config.gpio_pendown = gpio_pendown;
+	}
 
 	spi_register_board_info(&ads7846_spi_board_info, 1);
 }

arch/arm/mach-omap2/control.h

@@ -338,6 +338,11 @@
 #define AM35XX_HECC_SW_RST		BIT(3)
 #define AM35XX_VPFE_PCLK_SW_RST		BIT(4)
 
+/*
+ * CONTROL AM33XX STATUS register
+ */
+#define AM33XX_CONTROL_STATUS		0x040
+
 /*
  * CONTROL OMAP STATUS register to identify OMAP3 features
  */

arch/arm/mach-omap2/devices.c

@@ -276,7 +276,7 @@ int __init omap4_keyboard_init(struct omap4_keypad_platform_data
 }
 
 #if defined(CONFIG_OMAP_MBOX_FWK) || defined(CONFIG_OMAP_MBOX_FWK_MODULE)
-static inline void omap_init_mbox(void)
+static inline void __init omap_init_mbox(void)
 {
 	struct omap_hwmod *oh;
 	struct platform_device *pdev;
@@ -337,7 +337,7 @@ static inline void omap_init_audio(void) {}
 #if defined(CONFIG_SND_OMAP_SOC_MCPDM) || \
 		defined(CONFIG_SND_OMAP_SOC_MCPDM_MODULE)
 
-static void omap_init_mcpdm(void)
+static void __init omap_init_mcpdm(void)
 {
 	struct omap_hwmod *oh;
 	struct platform_device *pdev;
@@ -358,7 +358,7 @@ static inline void omap_init_mcpdm(void) {}
 #if defined(CONFIG_SND_OMAP_SOC_DMIC) || \
 		defined(CONFIG_SND_OMAP_SOC_DMIC_MODULE)
 
-static void omap_init_dmic(void)
+static void __init omap_init_dmic(void)
 {
 	struct omap_hwmod *oh;
 	struct platform_device *pdev;
@@ -380,7 +380,7 @@ static inline void omap_init_dmic(void) {}
 
 #include <plat/mcspi.h>
 
-static int omap_mcspi_init(struct omap_hwmod *oh, void *unused)
+static int __init omap_mcspi_init(struct omap_hwmod *oh, void *unused)
 {
 	struct platform_device *pdev;
 	char *name = "omap2_mcspi";

arch/arm/mach-omap2/display.c

@@ -124,7 +124,7 @@ static void omap4_hdmi_mux_pads(enum omap_hdmi_flags flags)
 	}
 }
 
-static int omap4_dsi_mux_pads(int dsi_id, unsigned lanes)
+static int __init omap4_dsi_mux_pads(int dsi_id, unsigned lanes)
 {
 	u32 enable_mask, enable_shift;
 	u32 pipd_mask, pipd_shift;
@@ -157,7 +157,7 @@ static int omap4_dsi_mux_pads(int dsi_id, unsigned lanes)
 	return 0;
 }
 
-int omap_hdmi_init(enum omap_hdmi_flags flags)
+int __init omap_hdmi_init(enum omap_hdmi_flags flags)
 {
 	if (cpu_is_omap44xx())
 		omap4_hdmi_mux_pads(flags);
@@ -165,7 +165,7 @@ int omap_hdmi_init(enum omap_hdmi_flags flags)
 	return 0;
 }
 
-static int omap_dsi_enable_pads(int dsi_id, unsigned lane_mask)
+static int __init omap_dsi_enable_pads(int dsi_id, unsigned lane_mask)
 {
 	if (cpu_is_omap44xx())
 		return omap4_dsi_mux_pads(dsi_id, lane_mask);
@@ -173,7 +173,7 @@ static int omap_dsi_enable_pads(int dsi_id, unsigned lane_mask)
 	return 0;
 }
 
-static void omap_dsi_disable_pads(int dsi_id, unsigned lane_mask)
+static void __init omap_dsi_disable_pads(int dsi_id, unsigned lane_mask)
 {
 	if (cpu_is_omap44xx())
 		omap4_dsi_mux_pads(dsi_id, 0);

arch/arm/mach-omap2/dma.c

@@ -227,7 +227,7 @@ static int __init omap2_system_dma_init_dev(struct omap_hwmod *oh, void *unused)
 
 	dma_stride		= OMAP2_DMA_STRIDE;
 	dma_common_ch_start	= CSDP;
-	if (cpu_is_omap3630() || cpu_is_omap4430())
+	if (cpu_is_omap3630() || cpu_is_omap44xx())
 		dma_common_ch_end = CCDN;
 	else
 		dma_common_ch_end = CCFN;

arch/arm/mach-omap2/gpio.c

@@ -24,7 +24,7 @@
 #include <plat/omap_hwmod.h>
 #include <plat/omap_device.h>
 
-static int omap2_gpio_dev_init(struct omap_hwmod *oh, void *unused)
+static int __init omap2_gpio_dev_init(struct omap_hwmod *oh, void *unused)
 {
 	struct platform_device *pdev;
 	struct omap_gpio_platform_data *pdata;

arch/arm/mach-omap2/gpmc-smsc911x.c

@@ -101,11 +101,14 @@ void __init gpmc_smsc911x_init(struct omap_smsc911x_platform_data *board_data)
 
 	gpmc_cfg = board_data;
 
+	if (!gpmc_cfg->id) {
 		ret = platform_device_register(&gpmc_smsc911x_regulator);
 		if (ret < 0) {
-		pr_err("Unable to register smsc911x regulators: %d\n", ret);
+			pr_err("Unable to register smsc911x regulators: %d\n",
+			       ret);
 			return;
 		}
+	}
 
 	if (gpmc_cs_request(gpmc_cfg->cs, SZ_16M, &cs_mem_base) < 0) {
 		pr_err("Failed to request GPMC mem region\n");

arch/arm/mach-omap2/gpmc.c

@@ -888,6 +888,7 @@ int gpmc_enable_hwecc(int cs, int mode, int dev_width, int ecc_size)
 	gpmc_write_reg(GPMC_ECC_CONFIG, val);
 	return 0;
 }
+EXPORT_SYMBOL_GPL(gpmc_enable_hwecc);
 
 /**
  * gpmc_calculate_ecc - generate non-inverted ecc bytes
@@ -918,3 +919,4 @@ int gpmc_calculate_ecc(int cs, const u_char *dat, u_char *ecc_code)
 	gpmc_ecc_used = -EINVAL;
 	return 0;
 }
+EXPORT_SYMBOL_GPL(gpmc_calculate_ecc);

arch/arm/mach-omap2/hsmmc.c

@@ -293,7 +293,7 @@ static inline void omap_hsmmc_mux(struct omap_mmc_platform_data *mmc_controller,
 	}
 }
 
-static int omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
+static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
 					struct omap_mmc_platform_data *mmc)
 {
 	char *hc_name;
@@ -429,66 +429,131 @@ static int omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
 }
 
 static int omap_hsmmc_done;
+
+void omap_hsmmc_late_init(struct omap2_hsmmc_info *c)
+{
+	struct platform_device *pdev;
+	struct omap_mmc_platform_data *mmc_pdata;
+	int res;
+
+	if (omap_hsmmc_done != 1)
+		return;
+
+	omap_hsmmc_done++;
+
+	for (; c->mmc; c++) {
+		if (!c->deferred)
+			continue;
+
+		pdev = c->pdev;
+		if (!pdev)
+			continue;
+
+		mmc_pdata = pdev->dev.platform_data;
+		if (!mmc_pdata)
+			continue;
+
+		mmc_pdata->slots[0].switch_pin = c->gpio_cd;
+		mmc_pdata->slots[0].gpio_wp = c->gpio_wp;
+
+		res = omap_device_register(pdev);
+		if (res)
+			pr_err("Could not late init MMC %s\n",
+			       c->name);
+	}
+}
+
 #define MAX_OMAP_MMC_HWMOD_NAME_LEN		16
 
-void omap_init_hsmmc(struct omap2_hsmmc_info *hsmmcinfo, int ctrl_nr)
+static void __init omap_hsmmc_init_one(struct omap2_hsmmc_info *hsmmcinfo,
+					int ctrl_nr)
 {
 	struct omap_hwmod *oh;
+	struct omap_hwmod *ohs[1];
+	struct omap_device *od;
 	struct platform_device *pdev;
 	char oh_name[MAX_OMAP_MMC_HWMOD_NAME_LEN];
 	struct omap_mmc_platform_data *mmc_data;
 	struct omap_mmc_dev_attr *mmc_dev_attr;
 	char *name;
-	int l;
+	int res;
 
 	mmc_data = kzalloc(sizeof(struct omap_mmc_platform_data), GFP_KERNEL);
 	if (!mmc_data) {
 		pr_err("Cannot allocate memory for mmc device!\n");
-		goto done;
+		return;
 	}
 
-	if (omap_hsmmc_pdata_init(hsmmcinfo, mmc_data) < 0) {
-		pr_err("%s fails!\n", __func__);
-		goto done;
-	}
+	res = omap_hsmmc_pdata_init(hsmmcinfo, mmc_data);
+	if (res < 0)
+		goto free_mmc;
+
 	omap_hsmmc_mux(mmc_data, (ctrl_nr - 1));
 
 	name = "omap_hsmmc";
-
-	l = snprintf(oh_name, MAX_OMAP_MMC_HWMOD_NAME_LEN,
+	res = snprintf(oh_name, MAX_OMAP_MMC_HWMOD_NAME_LEN,
 		     "mmc%d", ctrl_nr);
-	WARN(l >= MAX_OMAP_MMC_HWMOD_NAME_LEN,
+	WARN(res >= MAX_OMAP_MMC_HWMOD_NAME_LEN,
 	     "String buffer overflow in MMC%d device setup\n", ctrl_nr);
+
 	oh = omap_hwmod_lookup(oh_name);
 	if (!oh) {
 		pr_err("Could not look up %s\n", oh_name);
-		kfree(mmc_data->slots[0].name);
-		goto done;
+		goto free_name;
 	}
-
+	ohs[0] = oh;
 	if (oh->dev_attr != NULL) {
 		mmc_dev_attr = oh->dev_attr;
 		mmc_data->controller_flags = mmc_dev_attr->flags;
 	}
 
-	pdev = omap_device_build(name, ctrl_nr - 1, oh, mmc_data,
-		sizeof(struct omap_mmc_platform_data), NULL, 0, false);
-	if (IS_ERR(pdev)) {
-		WARN(1, "Can't build omap_device for %s:%s.\n", name, oh->name);
-		kfree(mmc_data->slots[0].name);
-		goto done;
+	pdev = platform_device_alloc(name, ctrl_nr - 1);
+	if (!pdev) {
+		pr_err("Could not allocate pdev for %s\n", name);
+		goto free_name;
 	}
-	/*
-	 * return device handle to board setup code
-	 * required to populate for regulator framework structure
-	 */
-	hsmmcinfo->dev = &pdev->dev;
+	dev_set_name(&pdev->dev, "%s.%d", pdev->name, pdev->id);
+
+	od = omap_device_alloc(pdev, ohs, 1, NULL, 0);
+	if (!od) {
+		pr_err("Could not allocate od for %s\n", name);
+		goto put_pdev;
+	}
+
+	res = platform_device_add_data(pdev, mmc_data,
+			      sizeof(struct omap_mmc_platform_data));
+	if (res) {
+		pr_err("Could not add pdata for %s\n", name);
+		goto put_pdev;
+	}
+
+	hsmmcinfo->pdev = pdev;
+
+	if (hsmmcinfo->deferred)
+		goto free_mmc;
+
+	res = omap_device_register(pdev);
+	if (res) {
+		pr_err("Could not register od for %s\n", name);
+		goto free_od;
+	}
+
+	goto free_mmc;
+
+free_od:
+	omap_device_delete(od);
+
+put_pdev:
+	platform_device_put(pdev);
+
+free_name:
+	kfree(mmc_data->slots[0].name);
 
-done:
+free_mmc:
 	kfree(mmc_data);
 }
 
-void omap2_hsmmc_init(struct omap2_hsmmc_info *controllers)
+void __init omap_hsmmc_init(struct omap2_hsmmc_info *controllers)
 {
 	u32 reg;
 
@@ -521,7 +586,7 @@ void omap2_hsmmc_init(struct omap2_hsmmc_info *controllers)
 	}
 
 	for (; controllers->mmc; controllers++)
-		omap_init_hsmmc(controllers, controllers->mmc);
+		omap_hsmmc_init_one(controllers, controllers->mmc);
 
 }
 

arch/arm/mach-omap2/hsmmc.h

@@ -21,10 +21,11 @@ struct omap2_hsmmc_info {
 	bool	no_off;		/* power_saving and power is not to go off */
 	bool	no_off_init;	/* no power off when not in MMC sleep state */
 	bool	vcc_aux_disable_is_sleep; /* Regulator off remapped to sleep */
+	bool	deferred;	/* mmc needs a deferred probe */
 	int	gpio_cd;	/* or -EINVAL */
 	int	gpio_wp;	/* or -EINVAL */
 	char	*name;		/* or NULL for default */
-	struct device *dev;	/* returned: pointer to mmc adapter */
+	struct platform_device *pdev;	/* mmc controller instance */
 	int	ocr_mask;	/* temporary HACK */
 	/* Remux (pad configuration) when powering on/off */
 	void (*remux)(struct device *dev, int slot, int power_on);
@@ -34,11 +35,16 @@ struct omap2_hsmmc_info {
 
 #if defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
 
-void omap2_hsmmc_init(struct omap2_hsmmc_info *);
+void omap_hsmmc_init(struct omap2_hsmmc_info *);
+void omap_hsmmc_late_init(struct omap2_hsmmc_info *);
 
 #else
 
-static inline void omap2_hsmmc_init(struct omap2_hsmmc_info *info)
+static inline void omap_hsmmc_init(struct omap2_hsmmc_info *info)
+{
+}
+
+static inline void omap_hsmmc_late_init(struct omap2_hsmmc_info *info)
 {
 }
 

arch/arm/mach-omap2/id.c

@@ -44,6 +44,8 @@ int omap_type(void)
 
 	if (cpu_is_omap24xx()) {
 		val = omap_ctrl_readl(OMAP24XX_CONTROL_STATUS);
+	} else if (cpu_is_am33xx()) {
+		val = omap_ctrl_readl(AM33XX_CONTROL_STATUS);
 	} else if (cpu_is_omap34xx()) {
 		val = omap_ctrl_readl(OMAP343X_CONTROL_STATUS);
 	} else if (cpu_is_omap44xx()) {

arch/arm/mach-omap2/io.c

@@ -43,14 +43,13 @@
 #include "clockdomain.h"
 #include <plat/omap_hwmod.h>
 #include <plat/multi.h>
-#include "common.h"
 
 /*
  * The machine specific code may provide the extra mapping besides the
  * default mapping provided here.
  */
 
-#ifdef CONFIG_ARCH_OMAP2
+#if defined(CONFIG_SOC_OMAP2420) || defined(CONFIG_SOC_OMAP2430)
 static struct map_desc omap24xx_io_desc[] __initdata = {
 	{
 		.virtual	= L3_24XX_VIRT,

arch/arm/mach-omap2/mcbsp.c

@@ -122,7 +122,7 @@ static int omap3_enable_st_clock(unsigned int id, bool enable)
 	return 0;
 }
 
-static int omap_init_mcbsp(struct omap_hwmod *oh, void *unused)
+static int __init omap_init_mcbsp(struct omap_hwmod *oh, void *unused)
 {
 	int id, count = 1;
 	char *name = "omap-mcbsp";

arch/arm/mach-omap2/mux.c

@@ -100,7 +100,7 @@ void omap_mux_write_array(struct omap_mux_partition *partition,
 
 static char *omap_mux_options;
 
-static int _omap_mux_init_gpio(struct omap_mux_partition *partition,
+static int __init _omap_mux_init_gpio(struct omap_mux_partition *partition,
 				      int gpio, int val)
 {
 	struct omap_mux_entry *e;
@@ -145,7 +145,7 @@ static int _omap_mux_init_gpio(struct omap_mux_partition *partition,
 	return 0;
 }
 
-int omap_mux_init_gpio(int gpio, int val)
+int __init omap_mux_init_gpio(int gpio, int val)
 {
 	struct omap_mux_partition *partition;
 	int ret;
@@ -159,7 +159,7 @@ int omap_mux_init_gpio(int gpio, int val)
 	return -ENODEV;
 }
 
-static int _omap_mux_get_by_name(struct omap_mux_partition *partition,
+static int __init _omap_mux_get_by_name(struct omap_mux_partition *partition,
 					const char *muxname,
 					struct omap_mux **found_mux)
 {
@@ -218,7 +218,7 @@ static int _omap_mux_get_by_name(struct omap_mux_partition *partition,
 	return -ENODEV;
 }
 
-static int
+static int __init
 omap_mux_get_by_name(const char *muxname,
 			struct omap_mux_partition **found_partition,
 			struct omap_mux **found_mux)
@@ -240,7 +240,7 @@ omap_mux_get_by_name(const char *muxname,
 	return -ENODEV;
 }
 
-int omap_mux_init_signal(const char *muxname, int val)
+int __init omap_mux_init_signal(const char *muxname, int val)
 {
 	struct omap_mux_partition *partition = NULL;
 	struct omap_mux *mux = NULL;

arch/arm/mach-omap2/omap-hotplug.c

@@ -33,7 +33,7 @@ int platform_cpu_kill(unsigned int cpu)
  * platform-specific code to shutdown a CPU
  * Called with IRQs disabled
  */
-void platform_cpu_die(unsigned int cpu)
+void __ref platform_cpu_die(unsigned int cpu)
 {
 	unsigned int this_cpu;
 

arch/arm/mach-omap2/omap-mpuss-lowpower.c

@@ -300,7 +300,7 @@ int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state)
  * @cpu : CPU ID
  * @power_state: CPU low power state.
  */
-int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state)
+int __cpuinit omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state)
 {
 	unsigned int cpu_state = 0;
 

arch/arm/mach-omap2/omap-wakeupgen.c

@@ -43,7 +43,6 @@
 
 static void __iomem *wakeupgen_base;
 static void __iomem *sar_base;
-static DEFINE_PER_CPU(u32 [NR_REG_BANKS], irqmasks);
 static DEFINE_SPINLOCK(wakeupgen_lock);
 static unsigned int irq_target_cpu[NR_IRQS];
 
@@ -67,14 +66,6 @@ static inline void sar_writel(u32 val, u32 offset, u8 idx)
 	__raw_writel(val, sar_base + offset + (idx * 4));
 }
 
-static void _wakeupgen_set_all(unsigned int cpu, unsigned int reg)
-{
-	u8 i;
-
-	for (i = 0; i < NR_REG_BANKS; i++)
-		wakeupgen_writel(reg, i, cpu);
-}
-
 static inline int _wakeupgen_get_irq_info(u32 irq, u32 *bit_posn, u8 *reg_index)
 {
 	unsigned int spi_irq;
@@ -130,22 +121,6 @@ static void _wakeupgen_set(unsigned int irq, unsigned int cpu)
 	wakeupgen_writel(val, i, cpu);
 }
 
-static void _wakeupgen_save_masks(unsigned int cpu)
-{
-	u8 i;
-
-	for (i = 0; i < NR_REG_BANKS; i++)
-		per_cpu(irqmasks, cpu)[i] = wakeupgen_readl(i, cpu);
-}
-
-static void _wakeupgen_restore_masks(unsigned int cpu)
-{
-	u8 i;
-
-	for (i = 0; i < NR_REG_BANKS; i++)
-		wakeupgen_writel(per_cpu(irqmasks, cpu)[i], i, cpu);
-}
-
 /*
  * Architecture specific Mask extension
  */
@@ -170,6 +145,33 @@ static void wakeupgen_unmask(struct irq_data *d)
 	spin_unlock_irqrestore(&wakeupgen_lock, flags);
 }
 
+#ifdef CONFIG_HOTPLUG_CPU
+static DEFINE_PER_CPU(u32 [NR_REG_BANKS], irqmasks);
+
+static void _wakeupgen_save_masks(unsigned int cpu)
+{
+	u8 i;
+
+	for (i = 0; i < NR_REG_BANKS; i++)
+		per_cpu(irqmasks, cpu)[i] = wakeupgen_readl(i, cpu);
+}
+
+static void _wakeupgen_restore_masks(unsigned int cpu)
+{
+	u8 i;
+
+	for (i = 0; i < NR_REG_BANKS; i++)
+		wakeupgen_writel(per_cpu(irqmasks, cpu)[i], i, cpu);
+}
+
+static void _wakeupgen_set_all(unsigned int cpu, unsigned int reg)
+{
+	u8 i;
+
+	for (i = 0; i < NR_REG_BANKS; i++)
+		wakeupgen_writel(reg, i, cpu);
+}
+
 /*
  * Mask or unmask all interrupts on given CPU.
  *	0 = Mask all interrupts on the 'cpu'
@@ -191,6 +193,7 @@ static void wakeupgen_irqmask_all(unsigned int cpu, unsigned int set)
 	}
 	spin_unlock_irqrestore(&wakeupgen_lock, flags);
 }
+#endif
 
 #ifdef CONFIG_CPU_PM
 /*

arch/arm/mach-omap2/omap_hwmod_44xx_data.c

@@ -28,7 +28,6 @@
 #include <plat/mcspi.h>
 #include <plat/mcbsp.h>
 #include <plat/mmc.h>
-#include <plat/i2c.h>
 #include <plat/dmtimer.h>
 #include <plat/common.h>
 

arch/arm/mach-omap2/pm.c

@@ -28,7 +28,7 @@
 
 static struct omap_device_pm_latency *pm_lats;
 
-static int _init_omap_device(char *name)
+static int __init _init_omap_device(char *name)
 {
 	struct omap_hwmod *oh;
 	struct platform_device *pdev;
@@ -49,7 +49,7 @@ static int _init_omap_device(char *name)
 /*
  * Build omap_devices for processors and bus.
  */
-static void omap2_init_processor_devices(void)
+static void __init omap2_init_processor_devices(void)
 {
 	_init_omap_device("mpu");
 	if (omap3_has_iva())

arch/arm/mach-omap2/powerdomain-common.c

@@ -13,6 +13,7 @@
 
 #include <linux/errno.h>
 #include <linux/kernel.h>
+#include <linux/bug.h>
 #include "pm.h"
 #include "cm.h"
 #include "cm-regbits-34xx.h"

arch/arm/mach-omap2/powerdomain2xxx_3xxx.c

@@ -15,6 +15,7 @@
 #include <linux/io.h>
 #include <linux/errno.h>
 #include <linux/delay.h>
+#include <linux/bug.h>
 
 #include <plat/prcm.h>
 

arch/arm/mach-omap2/powerdomain44xx.c

@@ -15,6 +15,7 @@
 #include <linux/io.h>
 #include <linux/errno.h>
 #include <linux/delay.h>
+#include <linux/bug.h>
 
 #include "powerdomain.h"
 #include <plat/prcm.h>

arch/arm/mach-omap2/powerdomains3xxx_data.c

@@ -13,6 +13,7 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
+#include <linux/bug.h>
 
 #include <plat/cpu.h>
 

arch/arm/mach-omap2/sr_device.c

@@ -69,7 +69,7 @@ static void __init sr_set_nvalues(struct omap_volt_data *volt_data,
 	sr_data->nvalue_count = count;
 }
 
-static int sr_dev_init(struct omap_hwmod *oh, void *user)
+static int __init sr_dev_init(struct omap_hwmod *oh, void *user)
 {
 	struct omap_sr_data *sr_data;
 	struct platform_device *pdev;

arch/arm/mach-omap2/vc.c

@@ -10,6 +10,7 @@
 #include <linux/kernel.h>
 #include <linux/delay.h>
 #include <linux/init.h>
+#include <linux/bug.h>
 
 #include <plat/cpu.h>
 

arch/arm/mach-omap2/vp.c

@@ -61,8 +61,8 @@ void __init omap_vp_init(struct voltagedomain *voltdm)
 	vddmin = voltdm->pmic->vp_vddmin;
 	vddmax = voltdm->pmic->vp_vddmax;
 
-	waittime = ((voltdm->pmic->step_size / voltdm->pmic->slew_rate) *
-		    sys_clk_rate) / 1000;
+	waittime = DIV_ROUND_UP(voltdm->pmic->step_size * sys_clk_rate,
+				1000 * voltdm->pmic->slew_rate);
 	vstepmin = voltdm->pmic->vp_vstepmin;
 	vstepmax = voltdm->pmic->vp_vstepmax;
 

arch/arm/mach-ux500/Kconfig

@@ -8,47 +8,55 @@ config UX500_SOC_COMMON
 	select PL310_ERRATA_753970
 	select ARM_ERRATA_754322
 	select ARM_ERRATA_764369
-
-menu "Ux500 SoC"
+	select CACHE_L2X0
 
 config UX500_SOC_DB5500
-	bool "DB5500"
+	bool
 	select MFD_DB5500_PRCMU
 
 config UX500_SOC_DB8500
-	bool "DB8500"
+	bool
 	select MFD_DB8500_PRCMU
 	select REGULATOR_DB8500_PRCMU
-
-endmenu
+	select CPU_FREQ_TABLE if CPU_FREQ
 
 menu "Ux500 target platform (boards)"
 
-config MACH_U8500
-	bool "U8500 Development platform"
-	depends on UX500_SOC_DB8500
-	select TPS6105X
+config MACH_MOP500
+	bool "U8500 Development platform, MOP500 versions"
+	select UX500_SOC_DB8500
+	select I2C
+	select I2C_NOMADIK
 	help
-	  Include support for the mop500 development platform.
+	  Include support for the MOP500 development platform.
 
 config MACH_HREFV60
-       bool "U85000 Development platform, HREFv60 version"
-       depends on UX500_SOC_DB8500
+	bool "U8500 Development platform, HREFv60 version"
+	select MACH_MOP500
 	help
 	  Include support for the HREFv60 new development platform.
+	  Includes HREFv70, v71 etc.
 
 config MACH_SNOWBALL
 	bool "U8500 Snowball platform"
-	depends on UX500_SOC_DB8500
-	select MACH_U8500
+	select MACH_MOP500
 	help
 	  Include support for the snowball development platform.
 
 config MACH_U5500
 	bool "U5500 Development platform"
-	depends on UX500_SOC_DB5500
+	select UX500_SOC_DB5500
 	help
 	  Include support for the U5500 development platform.
+
+config UX500_AUTO_PLATFORM
+	def_bool y
+	depends on !MACH_U5500
+	select MACH_MOP500
+	help
+	  At least one platform needs to be selected in order to build
+	  a working kernel. If everything else is disabled, this
+	  automatically enables MACH_MOP500.
 endmenu
 
 config UX500_DEBUG_UART

arch/arm/mach-ux500/Makefile

@@ -7,7 +7,7 @@ obj-y				:= clock.o cpu.o devices.o devices-common.o \
 obj-$(CONFIG_CACHE_L2X0)	+= cache-l2x0.o
 obj-$(CONFIG_UX500_SOC_DB5500)	+= cpu-db5500.o dma-db5500.o
 obj-$(CONFIG_UX500_SOC_DB8500)	+= cpu-db8500.o devices-db8500.o
-obj-$(CONFIG_MACH_U8500)	+= board-mop500.o board-mop500-sdi.o \
+obj-$(CONFIG_MACH_MOP500)	+= board-mop500.o board-mop500-sdi.o \
 				board-mop500-regulators.o \
 				board-mop500-uib.o board-mop500-stuib.o \
 				board-mop500-u8500uib.o \

arch/arm/mach-ux500/board-mop500-regulators.c

@@ -74,6 +74,26 @@ static struct regulator_consumer_supply ab8500_vtvout_consumers[] = {
 	REGULATOR_SUPPLY("vddadc", "ab8500-gpadc.0"),
 };
 
+static struct regulator_consumer_supply ab8500_vaud_consumers[] = {
+	/* AB8500 audio-codec main supply */
+	REGULATOR_SUPPLY("vaud", "ab8500-codec.0"),
+};
+
+static struct regulator_consumer_supply ab8500_vamic1_consumers[] = {
+	/* AB8500 audio-codec Mic1 supply */
+	REGULATOR_SUPPLY("vamic1", "ab8500-codec.0"),
+};
+
+static struct regulator_consumer_supply ab8500_vamic2_consumers[] = {
+	/* AB8500 audio-codec Mic2 supply */
+	REGULATOR_SUPPLY("vamic2", "ab8500-codec.0"),
+};
+
+static struct regulator_consumer_supply ab8500_vdmic_consumers[] = {
+	/* AB8500 audio-codec DMic supply */
+	REGULATOR_SUPPLY("vdmic", "ab8500-codec.0"),
+};
+
 static struct regulator_consumer_supply ab8500_vintcore_consumers[] = {
 	/* SoC core supply, no device */
 	REGULATOR_SUPPLY("v-intcore", NULL),
@@ -323,6 +343,8 @@ struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = {
 			.name = "V-AUD",
 			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
 		},
+		.num_consumer_supplies = ARRAY_SIZE(ab8500_vaud_consumers),
+		.consumer_supplies = ab8500_vaud_consumers,
 	},
 	/* supply for v-anamic1 VAMic1-LDO */
 	[AB8500_LDO_ANAMIC1] = {
@@ -330,6 +352,8 @@ struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = {
 			.name = "V-AMIC1",
 			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
 		},
+		.num_consumer_supplies = ARRAY_SIZE(ab8500_vamic1_consumers),
+		.consumer_supplies = ab8500_vamic1_consumers,
 	},
 	/* supply for v-amic2, VAMIC2 LDO, reuse constants for AMIC1 */
 	[AB8500_LDO_ANAMIC2] = {
@@ -337,6 +361,8 @@ struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = {
 			.name = "V-AMIC2",
 			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
 		},
+		.num_consumer_supplies = ARRAY_SIZE(ab8500_vamic2_consumers),
+		.consumer_supplies = ab8500_vamic2_consumers,
 	},
 	/* supply for v-dmic, VDMIC LDO */
 	[AB8500_LDO_DMIC] = {
@@ -344,6 +370,8 @@ struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = {
 			.name = "V-DMIC",
 			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
 		},
+		.num_consumer_supplies = ARRAY_SIZE(ab8500_vdmic_consumers),
+		.consumer_supplies = ab8500_vdmic_consumers,
 	},
 	/* supply for v-intcore12, VINTCORE12 LDO */
 	[AB8500_LDO_INTCORE] = {

arch/arm/mach-ux500/board-mop500-u8500uib.c

@@ -8,7 +8,6 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/i2c.h>
-#include <linux/gpio.h>
 #include <linux/interrupt.h>
 #include <linux/mfd/tc3589x.h>
 #include <linux/input/matrix_keypad.h>

arch/arm/mach-ux500/board-mop500.c

@@ -72,7 +72,7 @@ static struct platform_device snowball_led_dev = {
 };
 
 static struct ab8500_gpio_platform_data ab8500_gpio_pdata = {
-	.gpio_base		= MOP500_AB8500_GPIO(0),
+	.gpio_base		= MOP500_AB8500_PIN_GPIO(1),
 	.irq_base		= MOP500_AB8500_VIR_GPIO_IRQ_BASE,
 	/* config_reg is the initial configuration of ab8500 pins.
 	 * The pins can be configured as GPIO or alt functions based

arch/arm/mach-ux500/board-mop500.h

@@ -63,7 +63,7 @@
  * because the AB8500 GPIO pins are enumbered starting from 1, so the value in
  * parens matches the GPIO pin number in the data sheet.
  */
-#define MOP500_AB8500_GPIO(x)		(MOP500_EGPIO_END + (x) - 1)
+#define MOP500_AB8500_PIN_GPIO(x)	(MOP500_EGPIO_END + (x) - 1)
 /*Snowball AB8500 GPIO */
 #define SNOWBALL_VSMPS2_1V8_GPIO	MOP500_AB8500_PIN_GPIO(1)	/* SYSCLKREQ2/GPIO1 */
 #define SNOWBALL_PM_GPIO1_GPIO		MOP500_AB8500_PIN_GPIO(2)	/* SYSCLKREQ3/GPIO2 */

arch/arm/mach-ux500/clock.c

@@ -223,6 +223,13 @@ int clk_set_rate(struct clk *clk, unsigned long rate)
 }
 EXPORT_SYMBOL(clk_set_rate);
 
+int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	/*TODO*/
+	return -ENOSYS;
+}
+EXPORT_SYMBOL(clk_set_parent);
+
 static void clk_prcmu_enable(struct clk *clk)
 {
 	void __iomem *cg_set_reg = __io_address(U8500_PRCMU_BASE)

arch/arm/mach-ux500/clock.h

@@ -21,6 +21,7 @@ struct clkops {
 	void (*enable) (struct clk *);
 	void (*disable) (struct clk *);
 	unsigned long (*get_rate) (struct clk *);
+	int (*set_parent)(struct clk *, struct clk *);
 };
 
 /**

arch/arm/mach-ux500/devices-db8500.c

@@ -101,6 +101,9 @@ static const dma_addr_t dma40_tx_map[DB8500_DMA_NR_DEV] = {
 	[DB8500_DMA_DEV41_SD_MM3_TX] = -1,
 	[DB8500_DMA_DEV42_SD_MM4_TX] = -1,
 	[DB8500_DMA_DEV43_SD_MM5_TX] = -1,
+	[DB8500_DMA_DEV14_MSP2_TX] = U8500_MSP2_BASE + MSP_TX_RX_REG_OFFSET,
+	[DB8500_DMA_DEV30_MSP1_TX] = U8500_MSP1_BASE + MSP_TX_RX_REG_OFFSET,
+	[DB8500_DMA_DEV31_MSP0_TX_SLIM0_CH0_TX] = U8500_MSP0_BASE + MSP_TX_RX_REG_OFFSET,
 };
 
 /* Mapping between source event lines and physical device address */
@@ -133,6 +136,9 @@ static const dma_addr_t dma40_rx_map[DB8500_DMA_NR_DEV] = {
 	[DB8500_DMA_DEV41_SD_MM3_RX] = -1,
 	[DB8500_DMA_DEV42_SD_MM4_RX] = -1,
 	[DB8500_DMA_DEV43_SD_MM5_RX] = -1,
+	[DB8500_DMA_DEV14_MSP2_RX] = U8500_MSP2_BASE + MSP_TX_RX_REG_OFFSET,
+	[DB8500_DMA_DEV30_MSP3_RX] = U8500_MSP3_BASE + MSP_TX_RX_REG_OFFSET,
+	[DB8500_DMA_DEV31_MSP0_RX_SLIM0_CH0_RX] = U8500_MSP0_BASE + MSP_TX_RX_REG_OFFSET,
 };
 
 /* Reserved event lines for memcpy only */

arch/arm/mach-ux500/include/mach/hardware.h

@@ -30,6 +30,8 @@
 #include <mach/db8500-regs.h>
 #include <mach/db5500-regs.h>
 
+#define MSP_TX_RX_REG_OFFSET	0
+
 #ifndef __ASSEMBLY__
 
 #include <mach/id.h>

arch/arm/mach-ux500/include/mach/irqs.h

@@ -43,7 +43,7 @@
 /* This will be overridden by board-specific irq headers */
 #define IRQ_BOARD_END		IRQ_BOARD_START
 
-#ifdef CONFIG_MACH_U8500
+#ifdef CONFIG_MACH_MOP500
 #include <mach/irqs-board-mop500.h>
 #endif
 

arch/arm/plat-mxc/include/mach/iomux-mx25.h

@@ -139,15 +139,15 @@
 #define MX25_PAD_NFRB__GPIO_3_31	IOMUX_PAD(0x27c, 0x084, 0x15, 0, 0, NO_PAD_CTRL)
 
 #define MX25_PAD_D15__D15		IOMUX_PAD(0x280, 0x088, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D15__LD16		IOMUX_PAD(0x280, 0x088, 0x01, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_D15__LD16		IOMUX_PAD(0x280, 0x088, 0x01, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_D15__GPIO_4_5		IOMUX_PAD(0x280, 0x088, 0x05, 0, 0, NO_PAD_CTRL)
 
 #define MX25_PAD_D14__D14		IOMUX_PAD(0x284, 0x08c, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D14__LD17		IOMUX_PAD(0x284, 0x08c, 0x01, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_D14__LD17		IOMUX_PAD(0x284, 0x08c, 0x01, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_D14__GPIO_4_6		IOMUX_PAD(0x284, 0x08c, 0x05, 0, 0, NO_PAD_CTRL)
 
 #define MX25_PAD_D13__D13		IOMUX_PAD(0x288, 0x090, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D13__LD18		IOMUX_PAD(0x288, 0x090, 0x01, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_D13__LD18		IOMUX_PAD(0x288, 0x090, 0x01, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_D13__GPIO_4_7		IOMUX_PAD(0x288, 0x090, 0x05, 0, 0, NO_PAD_CTRL)
 
 #define MX25_PAD_D12__D12		IOMUX_PAD(0x28c, 0x094, 0x00, 0, 0, NO_PAD_CTRL)
@@ -192,54 +192,54 @@
 #define MX25_PAD_D0__D0			IOMUX_PAD(0x2bc, 0x0c4, 0x00, 0, 0, NO_PAD_CTRL)
 #define MX25_PAD_D0__GPIO_4_20		IOMUX_PAD(0x2bc, 0x0c4, 0x05, 0, 0, NO_PAD_CTRL)
 
-#define MX25_PAD_LD0__LD0		IOMUX_PAD(0x2c0, 0x0c8, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD0__LD0		IOMUX_PAD(0x2c0, 0x0c8, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD0__CSI_D0		IOMUX_PAD(0x2c0, 0x0c8, 0x12, 0x488, 0, NO_PAD_CTRL)
 #define MX25_PAD_LD0__GPIO_2_15		IOMUX_PAD(0x2c0, 0x0c8, 0x15, 0, 0, NO_PAD_CTRL)
 
-#define MX25_PAD_LD1__LD1		IOMUX_PAD(0x2c4, 0x0cc, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD1__LD1		IOMUX_PAD(0x2c4, 0x0cc, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD1__CSI_D1		IOMUX_PAD(0x2c4, 0x0cc, 0x12, 0x48c, 0, NO_PAD_CTRL)
 #define MX25_PAD_LD1__GPIO_2_16		IOMUX_PAD(0x2c4, 0x0cc, 0x15, 0, 0, NO_PAD_CTRL)
 
-#define MX25_PAD_LD2__LD2		IOMUX_PAD(0x2c8, 0x0d0, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD2__LD2		IOMUX_PAD(0x2c8, 0x0d0, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD2__GPIO_2_17		IOMUX_PAD(0x2c8, 0x0d0, 0x15, 0, 0, NO_PAD_CTRL)
 
-#define MX25_PAD_LD3__LD3		IOMUX_PAD(0x2cc, 0x0d4, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD3__LD3		IOMUX_PAD(0x2cc, 0x0d4, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD3__GPIO_2_18		IOMUX_PAD(0x2cc, 0x0d4, 0x15, 0, 0, NO_PAD_CTRL)
 
-#define MX25_PAD_LD4__LD4		IOMUX_PAD(0x2d0, 0x0d8, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD4__LD4		IOMUX_PAD(0x2d0, 0x0d8, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD4__GPIO_2_19		IOMUX_PAD(0x2d0, 0x0d8, 0x15, 0, 0, NO_PAD_CTRL)
 
-#define MX25_PAD_LD5__LD5		IOMUX_PAD(0x2d4, 0x0dc, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD5__LD5		IOMUX_PAD(0x2d4, 0x0dc, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD5__GPIO_1_19		IOMUX_PAD(0x2d4, 0x0dc, 0x15, 0, 0, NO_PAD_CTRL)
 
-#define MX25_PAD_LD6__LD6		IOMUX_PAD(0x2d8, 0x0e0, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD6__LD6		IOMUX_PAD(0x2d8, 0x0e0, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD6__GPIO_1_20		IOMUX_PAD(0x2d8, 0x0e0, 0x15, 0, 0, NO_PAD_CTRL)
 
-#define MX25_PAD_LD7__LD7		IOMUX_PAD(0x2dc, 0x0e4, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD7__LD7		IOMUX_PAD(0x2dc, 0x0e4, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD7__GPIO_1_21		IOMUX_PAD(0x2dc, 0x0e4, 0x15, 0, 0, NO_PAD_CTRL)
 
-#define MX25_PAD_LD8__LD8		IOMUX_PAD(0x2e0, 0x0e8, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD8__LD8		IOMUX_PAD(0x2e0, 0x0e8, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD8__FEC_TX_ERR	IOMUX_PAD(0x2e0, 0x0e8, 0x15, 0, 0, NO_PAD_CTRL)
 
-#define MX25_PAD_LD9__LD9		IOMUX_PAD(0x2e4, 0x0ec, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD9__LD9		IOMUX_PAD(0x2e4, 0x0ec, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD9__FEC_COL		IOMUX_PAD(0x2e4, 0x0ec, 0x15, 0x504, 1, NO_PAD_CTRL)
 
-#define MX25_PAD_LD10__LD10		IOMUX_PAD(0x2e8, 0x0f0, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD10__LD10		IOMUX_PAD(0x2e8, 0x0f0, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD10__FEC_RX_ER	IOMUX_PAD(0x2e8, 0x0f0, 0x15, 0x518, 1, NO_PAD_CTRL)
 
-#define MX25_PAD_LD11__LD11		IOMUX_PAD(0x2ec, 0x0f4, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD11__LD11		IOMUX_PAD(0x2ec, 0x0f4, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD11__FEC_RDATA2	IOMUX_PAD(0x2ec, 0x0f4, 0x15, 0x50c, 1, NO_PAD_CTRL)
 
-#define MX25_PAD_LD12__LD12		IOMUX_PAD(0x2f0, 0x0f8, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD12__LD12		IOMUX_PAD(0x2f0, 0x0f8, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD12__FEC_RDATA3	IOMUX_PAD(0x2f0, 0x0f8, 0x15, 0x510, 1, NO_PAD_CTRL)
 
-#define MX25_PAD_LD13__LD13		IOMUX_PAD(0x2f4, 0x0fc, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD13__LD13		IOMUX_PAD(0x2f4, 0x0fc, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD13__FEC_TDATA2	IOMUX_PAD(0x2f4, 0x0fc, 0x15, 0, 0, NO_PAD_CTRL)
 
-#define MX25_PAD_LD14__LD14		IOMUX_PAD(0x2f8, 0x100, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD14__LD14		IOMUX_PAD(0x2f8, 0x100, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD14__FEC_TDATA3	IOMUX_PAD(0x2f8, 0x100, 0x15, 0, 0, NO_PAD_CTRL)
 
-#define MX25_PAD_LD15__LD15		IOMUX_PAD(0x2fc, 0x104, 0x10, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_LD15__LD15		IOMUX_PAD(0x2fc, 0x104, 0x10, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_LD15__FEC_RX_CLK	IOMUX_PAD(0x2fc, 0x104, 0x15, 0x514, 1, NO_PAD_CTRL)
 
 #define MX25_PAD_HSYNC__HSYNC		IOMUX_PAD(0x300, 0x108, 0x10, 0, 0, NO_PAD_CTRL)
@@ -468,11 +468,11 @@
 #define MX25_PAD_GPIO_C__CAN2_TX	IOMUX_PAD(0x3f8, 0x1fc, 0x16, 0, 0, PAD_CTL_PUS_22K_UP)
 
 #define MX25_PAD_GPIO_D__GPIO_D		IOMUX_PAD(0x3fc, 0x200, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_GPIO_E__LD16		IOMUX_PAD(0x400, 0x204, 0x02, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_GPIO_E__LD16		IOMUX_PAD(0x400, 0x204, 0x02, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_GPIO_D__CAN2_RX	IOMUX_PAD(0x3fc, 0x200, 0x16, 0x484, 1, PAD_CTL_PUS_22K_UP)
 
 #define MX25_PAD_GPIO_E__GPIO_E		IOMUX_PAD(0x400, 0x204, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_GPIO_F__LD17		IOMUX_PAD(0x404, 0x208, 0x02, 0, 0, NO_PAD_CTRL)
+#define MX25_PAD_GPIO_F__LD17		IOMUX_PAD(0x404, 0x208, 0x02, 0, 0, PAD_CTL_SRE_FAST)
 #define MX25_PAD_GPIO_E__AUD7_TXD	IOMUX_PAD(0x400, 0x204, 0x14, 0, 0, NO_PAD_CTRL)
 
 #define MX25_PAD_GPIO_F__GPIO_F		IOMUX_PAD(0x404, 0x208, 0x10, 0, 0, NO_PAD_CTRL)

arch/arm/plat-omap/clock.c

@@ -20,7 +20,6 @@
 #include <linux/clk.h>
 #include <linux/mutex.h>
 #include <linux/cpufreq.h>
-#include <linux/debugfs.h>
 #include <linux/io.h>
 
 #include <plat/clock.h>

arch/arm/plat-omap/dma.c

@@ -2125,7 +2125,7 @@ static int __devexit omap_system_dma_remove(struct platform_device *pdev)
 
 static struct platform_driver omap_system_dma_driver = {
 	.probe		= omap_system_dma_probe,
-	.remove		= omap_system_dma_remove,
+	.remove		= __devexit_p(omap_system_dma_remove),
 	.driver		= {
 		.name	= "omap_dma_system"
 	},

arch/arm/plat-omap/dmtimer.c

@@ -80,9 +80,9 @@ static void omap_dm_timer_write_reg(struct omap_dm_timer *timer, u32 reg,
 
 static void omap_timer_restore_context(struct omap_dm_timer *timer)
 {
-	omap_dm_timer_write_reg(timer, OMAP_TIMER_OCP_CFG_OFFSET,
-				timer->context.tiocp_cfg);
-	if (timer->revision > 1)
+	__raw_writel(timer->context.tiocp_cfg,
+			timer->io_base + OMAP_TIMER_OCP_CFG_OFFSET);
+	if (timer->revision == 1)
 		__raw_writel(timer->context.tistat, timer->sys_stat);
 
 	__raw_writel(timer->context.tisr, timer->irq_stat);
@@ -357,6 +357,19 @@ int omap_dm_timer_stop(struct omap_dm_timer *timer)
 
 	__omap_dm_timer_stop(timer, timer->posted, rate);
 
+	if (timer->loses_context && timer->get_context_loss_count)
+		timer->ctx_loss_count =
+			timer->get_context_loss_count(&timer->pdev->dev);
+
+	/*
+	 * Since the register values are computed and written within
+	 * __omap_dm_timer_stop, we need to use read to retrieve the
+	 * context.
+	 */
+	timer->context.tclr =
+			omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
+	timer->context.tisr = __raw_readl(timer->irq_stat);
+	omap_dm_timer_disable(timer);
 	return 0;
 }
 EXPORT_SYMBOL_GPL(omap_dm_timer_stop);

arch/arm/plat-omap/include/plat/cpu.h

@@ -250,7 +250,6 @@ IS_AM_SUBCLASS(335x, 0x335)
  * cpu_is_omap2423():	True for OMAP2423
  * cpu_is_omap2430():	True for OMAP2430
  * cpu_is_omap3430():	True for OMAP3430
- * cpu_is_omap4430():	True for OMAP4430
  * cpu_is_omap3505():	True for OMAP3505
  * cpu_is_omap3517():	True for OMAP3517
  */
@@ -299,7 +298,6 @@ IS_OMAP_TYPE(3517, 0x3517)
 #define cpu_is_omap3505()		0
 #define cpu_is_omap3517()		0
 #define cpu_is_omap3430()		0
-#define cpu_is_omap4430()		0
 #define cpu_is_omap3630()		0
 
 /*

arch/arm/plat-omap/include/plat/omap_device.h

@@ -100,6 +100,13 @@ struct platform_device *omap_device_build_ss(const char *pdev_name, int pdev_id,
 					 struct omap_device_pm_latency *pm_lats,
 					 int pm_lats_cnt, int is_early_device);
 
+struct omap_device *omap_device_alloc(struct platform_device *pdev,
+				      struct omap_hwmod **ohs, int oh_cnt,
+				      struct omap_device_pm_latency *pm_lats,
+				      int pm_lats_cnt);
+void omap_device_delete(struct omap_device *od);
+int omap_device_register(struct platform_device *pdev);
+
 void __iomem *omap_device_get_rt_va(struct omap_device *od);
 struct device *omap_device_get_by_hwmod_name(const char *oh_name);
 

arch/arm/plat-omap/include/plat/sram.h

@@ -101,4 +101,5 @@ static inline void omap_push_sram_idle(void) {}
 #else
 #define OMAP4_SRAM_PA		0x40300000
 #endif
+#define AM33XX_SRAM_PA		0x40300000
 #endif

arch/arm/plat-omap/omap_device.c

+
 /*
  * omap_device implementation
  *
@@ -97,14 +98,7 @@
 #define USE_WAKEUP_LAT			0
 #define IGNORE_WAKEUP_LAT		1
 
-static int omap_device_register(struct platform_device *pdev);
 static int omap_early_device_register(struct platform_device *pdev);
-static struct omap_device *omap_device_alloc(struct platform_device *pdev,
-				      struct omap_hwmod **ohs, int oh_cnt,
-				      struct omap_device_pm_latency *pm_lats,
-				      int pm_lats_cnt);
-static void omap_device_delete(struct omap_device *od);
-
 
 static struct omap_device_pm_latency omap_default_latency[] = {
 	{
@@ -509,7 +503,7 @@ static int omap_device_fill_resources(struct omap_device *od,
  *
  * Returns an struct omap_device pointer or ERR_PTR() on error;
  */
-static struct omap_device *omap_device_alloc(struct platform_device *pdev,
+struct omap_device *omap_device_alloc(struct platform_device *pdev,
 					struct omap_hwmod **ohs, int oh_cnt,
 					struct omap_device_pm_latency *pm_lats,
 					int pm_lats_cnt)
@@ -591,7 +585,7 @@ static struct omap_device *omap_device_alloc(struct platform_device *pdev,
 	return ERR_PTR(ret);
 }
 
-static void omap_device_delete(struct omap_device *od)
+void omap_device_delete(struct omap_device *od)
 {
 	if (!od)
 		return;
@@ -619,7 +613,7 @@ static void omap_device_delete(struct omap_device *od)
  * information.  Returns ERR_PTR(-EINVAL) if @oh is NULL; otherwise,
  * passes along the return value of omap_device_build_ss().
  */
-struct platform_device *omap_device_build(const char *pdev_name, int pdev_id,
+struct platform_device __init *omap_device_build(const char *pdev_name, int pdev_id,
 				      struct omap_hwmod *oh, void *pdata,
 				      int pdata_len,
 				      struct omap_device_pm_latency *pm_lats,
@@ -652,7 +646,7 @@ struct platform_device *omap_device_build(const char *pdev_name, int pdev_id,
  * platform_device record.  Returns an ERR_PTR() on error, or passes
  * along the return value of omap_device_register().
  */
-struct platform_device *omap_device_build_ss(const char *pdev_name, int pdev_id,
+struct platform_device __init *omap_device_build_ss(const char *pdev_name, int pdev_id,
 					 struct omap_hwmod **ohs, int oh_cnt,
 					 void *pdata, int pdata_len,
 					 struct omap_device_pm_latency *pm_lats,
@@ -717,7 +711,7 @@ struct platform_device *omap_device_build_ss(const char *pdev_name, int pdev_id,
  * platform_early_add_device() on the underlying platform_device.
  * Returns 0 by default.
  */
-static int omap_early_device_register(struct platform_device *pdev)
+static int __init omap_early_device_register(struct platform_device *pdev)
 {
 	struct platform_device *devices[1];
 
@@ -817,7 +811,7 @@ static struct dev_pm_domain omap_device_pm_domain = {
  * platform_device_register() on the underlying platform_device.
  * Returns the return value of platform_device_register().
  */
-static int omap_device_register(struct platform_device *pdev)
+int omap_device_register(struct platform_device *pdev)
 {
 	pr_debug("omap_device: %s: registering\n", pdev->name);
 

arch/arm/plat-omap/sram.c

@@ -86,7 +86,7 @@ static int is_sram_locked(void)
 			__raw_writel(0xCFDE, OMAP24XX_VA_READPERM0);  /* all i-read */
 			__raw_writel(0xCFDE, OMAP24XX_VA_WRITEPERM0); /* all i-write */
 		}
-		if (cpu_is_omap34xx()) {
+		if (cpu_is_omap34xx() && !cpu_is_am33xx()) {
 			__raw_writel(0xFFFF, OMAP34XX_VA_REQINFOPERM0); /* all q-vects */
 			__raw_writel(0xFFFF, OMAP34XX_VA_READPERM0);  /* all i-read */
 			__raw_writel(0xFFFF, OMAP34XX_VA_WRITEPERM0); /* all i-write */
@@ -124,7 +124,10 @@ static void __init omap_detect_sram(void)
 				omap_sram_size = 0x800; /* 2K */
 			}
 		} else {
-			if (cpu_is_omap34xx()) {
+			if (cpu_is_am33xx()) {
+				omap_sram_start = AM33XX_SRAM_PA;
+				omap_sram_size = 0x10000; /* 64K */
+			} else if (cpu_is_omap34xx()) {
 				omap_sram_start = OMAP3_SRAM_PA;
 				omap_sram_size = 0x10000; /* 64K */
 			} else if (cpu_is_omap44xx()) {
@@ -368,6 +371,11 @@ static inline int omap34xx_sram_init(void)
 	return 0;
 }
 
+static inline int am33xx_sram_init(void)
+{
+	return 0;
+}
+
 int __init omap_sram_init(void)
 {
 	omap_detect_sram();
@@ -379,6 +387,8 @@ int __init omap_sram_init(void)
 		omap242x_sram_init();
 	else if (cpu_is_omap2430())
 		omap243x_sram_init();
+	else if (cpu_is_am33xx())
+		am33xx_sram_init();
 	else if (cpu_is_omap34xx())
 		omap34xx_sram_init();