[PATCH] libata: Marvell SATA support (PIO mode)

This is my libata compatible low level driver for the Marvell SATA
family.  Currently it successfully runs in PIO mode on a 6081 chip.
EDMA support is in the works and should be done shortly.  Review,
testing (especially on other flavors of Marvell), comments welcome.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

drivers/scsi/Kconfig

@@ -459,6 +459,15 @@ config SCSI_ATA_PIIX
 
 	  If unsure, say N.
 
+config SCSI_SATA_MV
+	tristate "Marvell SATA support"
+	depends on SCSI_SATA && PCI && EXPERIMENTAL
+	help
+	  This option enables support for the Marvell Serial ATA family.
+	  Currently supports 88SX[56]0[48][01] chips.
+
+	  If unsure, say N.
+
 config SCSI_SATA_NV
 	tristate "NVIDIA SATA support"
 	depends on SCSI_SATA && PCI && EXPERIMENTAL

drivers/scsi/Makefile

@@ -132,6 +132,7 @@ obj-$(CONFIG_SCSI_SATA_SIS)	+= libata.o sata_sis.o
 obj-$(CONFIG_SCSI_SATA_SX4)	+= libata.o sata_sx4.o
 obj-$(CONFIG_SCSI_SATA_NV)	+= libata.o sata_nv.o
 obj-$(CONFIG_SCSI_SATA_ULI)	+= libata.o sata_uli.o
+obj-$(CONFIG_SCSI_SATA_MV)	+= libata.o sata_mv.o
 
 obj-$(CONFIG_ARM)		+= arm/
 

drivers/scsi/sata_mv.c

+/*
+ * sata_mv.c - Marvell SATA support
+ *
+ * Copyright 2005: EMC Corporation, all rights reserved. 
+ *
+ * Please ALWAYS copy linux-ide@vger.kernel.org on emails.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/dma-mapping.h>
+#include "scsi.h"
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <asm/io.h>
+
+#define DRV_NAME	"sata_mv"
+#define DRV_VERSION	"0.12"
+
+enum {
+	/* BAR's are enumerated in terms of pci_resource_start() terms */
+	MV_PRIMARY_BAR		= 0,	/* offset 0x10: memory space */
+	MV_IO_BAR		= 2,	/* offset 0x18: IO space */
+	MV_MISC_BAR		= 3,	/* offset 0x1c: FLASH, NVRAM, SRAM */
+
+	MV_MAJOR_REG_AREA_SZ	= 0x10000,	/* 64KB */
+	MV_MINOR_REG_AREA_SZ	= 0x2000,	/* 8KB */
+
+	MV_PCI_REG_BASE		= 0,
+	MV_IRQ_COAL_REG_BASE	= 0x18000,	/* 6xxx part only */
+	MV_SATAHC0_REG_BASE	= 0x20000,
+
+	MV_PCI_REG_SZ		= MV_MAJOR_REG_AREA_SZ,
+	MV_SATAHC_REG_SZ	= MV_MAJOR_REG_AREA_SZ,
+	MV_SATAHC_ARBTR_REG_SZ	= MV_MINOR_REG_AREA_SZ,		/* arbiter */
+	MV_PORT_REG_SZ		= MV_MINOR_REG_AREA_SZ,
+
+	MV_Q_CT			= 32,
+	MV_CRQB_SZ		= 32,
+	MV_CRPB_SZ		= 8,
+
+	MV_DMA_BOUNDARY		= 0xffffffffU,
+	SATAHC_MASK		= (~(MV_SATAHC_REG_SZ - 1)),
+
+	MV_PORTS_PER_HC		= 4,
+	/* == (port / MV_PORTS_PER_HC) to determine HC from 0-7 port */
+	MV_PORT_HC_SHIFT	= 2,
+	/* == (port % MV_PORTS_PER_HC) to determine port from 0-7 port */
+	MV_PORT_MASK		= 3,
+
+	/* Host Flags */
+	MV_FLAG_DUAL_HC		= (1 << 30),  /* two SATA Host Controllers */
+	MV_FLAG_IRQ_COALESCE	= (1 << 29),  /* IRQ coalescing capability */
+	MV_FLAG_BDMA		= (1 << 28),  /* Basic DMA */
+
+	chip_504x		= 0,
+	chip_508x		= 1,
+	chip_604x		= 2,
+	chip_608x		= 3,
+
+	/* PCI interface registers */
+
+	PCI_MAIN_CMD_STS_OFS	= 0xd30,
+	STOP_PCI_MASTER		= (1 << 2),
+	PCI_MASTER_EMPTY	= (1 << 3),
+	GLOB_SFT_RST		= (1 << 4),
+
+	PCI_IRQ_CAUSE_OFS	= 0x1d58,
+	PCI_IRQ_MASK_OFS	= 0x1d5c,
+	PCI_UNMASK_ALL_IRQS	= 0x7fffff,	/* bits 22-0 */
+
+	HC_MAIN_IRQ_CAUSE_OFS	= 0x1d60,
+	HC_MAIN_IRQ_MASK_OFS	= 0x1d64,
+	PORT0_ERR		= (1 << 0),	/* shift by port # */
+	PORT0_DONE		= (1 << 1),	/* shift by port # */
+	HC0_IRQ_PEND		= 0x1ff,	/* bits 0-8 = HC0's ports */
+	HC_SHIFT		= 9,		/* bits 9-17 = HC1's ports */
+	PCI_ERR			= (1 << 18),
+	TRAN_LO_DONE		= (1 << 19),	/* 6xxx: IRQ coalescing */
+	TRAN_HI_DONE		= (1 << 20),	/* 6xxx: IRQ coalescing */
+	PORTS_0_7_COAL_DONE	= (1 << 21),	/* 6xxx: IRQ coalescing */
+	GPIO_INT		= (1 << 22),
+	SELF_INT		= (1 << 23),
+	TWSI_INT		= (1 << 24),
+	HC_MAIN_RSVD		= (0x7f << 25),	/* bits 31-25 */
+	HC_MAIN_MASKED_IRQS	= (TRAN_LO_DONE | TRAN_HI_DONE | 
+				   PORTS_0_7_COAL_DONE | GPIO_INT | TWSI_INT |
+				   HC_MAIN_RSVD),
+
+	/* SATAHC registers */
+	HC_CFG_OFS		= 0,
+
+	HC_IRQ_CAUSE_OFS	= 0x14,
+	CRBP_DMA_DONE		= (1 << 0),	/* shift by port # */
+	HC_IRQ_COAL		= (1 << 4),	/* IRQ coalescing */
+	DEV_IRQ			= (1 << 8),	/* shift by port # */
+
+	/* Shadow block registers */
+	SHD_PIO_DATA_OFS	= 0x100,
+	SHD_FEA_ERR_OFS		= 0x104,
+	SHD_SECT_CNT_OFS	= 0x108,
+	SHD_LBA_L_OFS		= 0x10C,
+	SHD_LBA_M_OFS		= 0x110,
+	SHD_LBA_H_OFS		= 0x114,
+	SHD_DEV_HD_OFS		= 0x118,
+	SHD_CMD_STA_OFS		= 0x11C,
+	SHD_CTL_AST_OFS		= 0x120,
+
+	/* SATA registers */
+	SATA_STATUS_OFS		= 0x300,  /* ctrl, err regs follow status */
+	SATA_ACTIVE_OFS		= 0x350,
+
+	/* Port registers */
+	EDMA_CFG_OFS		= 0,
+
+	EDMA_ERR_IRQ_CAUSE_OFS	= 0x8,
+	EDMA_ERR_IRQ_MASK_OFS	= 0xc,
+	EDMA_ERR_D_PAR		= (1 << 0),
+	EDMA_ERR_PRD_PAR	= (1 << 1),
+	EDMA_ERR_DEV		= (1 << 2),
+	EDMA_ERR_DEV_DCON	= (1 << 3),
+	EDMA_ERR_DEV_CON	= (1 << 4),
+	EDMA_ERR_SERR		= (1 << 5),
+	EDMA_ERR_SELF_DIS	= (1 << 7),
+	EDMA_ERR_BIST_ASYNC	= (1 << 8),
+	EDMA_ERR_CRBQ_PAR	= (1 << 9),
+	EDMA_ERR_CRPB_PAR	= (1 << 10),
+	EDMA_ERR_INTRL_PAR	= (1 << 11),
+	EDMA_ERR_IORDY		= (1 << 12),
+	EDMA_ERR_LNK_CTRL_RX	= (0xf << 13),
+	EDMA_ERR_LNK_CTRL_RX_2	= (1 << 15),
+	EDMA_ERR_LNK_DATA_RX	= (0xf << 17),
+	EDMA_ERR_LNK_CTRL_TX	= (0x1f << 21),
+	EDMA_ERR_LNK_DATA_TX	= (0x1f << 26),
+	EDMA_ERR_TRANS_PROTO	= (1 << 31),
+	EDMA_ERR_FATAL		= (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR | 
+				   EDMA_ERR_DEV_DCON | EDMA_ERR_CRBQ_PAR |
+				   EDMA_ERR_CRPB_PAR | EDMA_ERR_INTRL_PAR |
+				   EDMA_ERR_IORDY | EDMA_ERR_LNK_CTRL_RX_2 | 
+				   EDMA_ERR_LNK_DATA_RX |
+				   EDMA_ERR_LNK_DATA_TX | 
+				   EDMA_ERR_TRANS_PROTO),
+
+	EDMA_CMD_OFS		= 0x28,
+	EDMA_EN			= (1 << 0),
+	EDMA_DS			= (1 << 1),
+	ATA_RST			= (1 << 2),
+
+	/* BDMA is 6xxx part only */
+	BDMA_CMD_OFS		= 0x224,
+	BDMA_START		= (1 << 0),
+
+	MV_UNDEF		= 0,
+};
+
+struct mv_port_priv {
+
+};
+
+struct mv_host_priv {
+
+};
+
+static void mv_irq_clear(struct ata_port *ap);
+static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in);
+static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
+static void mv_phy_reset(struct ata_port *ap);
+static int mv_master_reset(void __iomem *mmio_base);
+static irqreturn_t mv_interrupt(int irq, void *dev_instance,
+				struct pt_regs *regs);
+static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
+
+static Scsi_Host_Template mv_sht = {
+	.module			= THIS_MODULE,
+	.name			= DRV_NAME,
+	.ioctl			= ata_scsi_ioctl,
+	.queuecommand		= ata_scsi_queuecmd,
+	.eh_strategy_handler	= ata_scsi_error,
+	.can_queue		= ATA_DEF_QUEUE,
+	.this_id		= ATA_SHT_THIS_ID,
+	.sg_tablesize		= MV_UNDEF,
+	.max_sectors		= ATA_MAX_SECTORS,
+	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
+	.emulated		= ATA_SHT_EMULATED,
+	.use_clustering		= MV_UNDEF,
+	.proc_name		= DRV_NAME,
+	.dma_boundary		= MV_DMA_BOUNDARY,
+	.slave_configure	= ata_scsi_slave_config,
+	.bios_param		= ata_std_bios_param,
+	.ordered_flush		= 1,
+};
+
+static struct ata_port_operations mv_ops = {
+	.port_disable		= ata_port_disable,
+
+	.tf_load		= ata_tf_load,
+	.tf_read		= ata_tf_read,
+	.check_status		= ata_check_status,
+	.exec_command		= ata_exec_command,
+	.dev_select		= ata_std_dev_select,
+
+	.phy_reset		= mv_phy_reset,
+
+	.qc_prep		= ata_qc_prep,
+	.qc_issue		= ata_qc_issue_prot,
+
+	.eng_timeout		= ata_eng_timeout,
+
+	.irq_handler		= mv_interrupt,
+	.irq_clear		= mv_irq_clear,
+
+	.scr_read		= mv_scr_read,
+	.scr_write		= mv_scr_write,
+
+	.port_start		= ata_port_start,
+	.port_stop		= ata_port_stop,
+	.host_stop		= ata_host_stop,
+};
+
+static struct ata_port_info mv_port_info[] = {
+	{  /* chip_504x */
+		.sht		= &mv_sht,
+		.host_flags	= (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+				   ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO),
+		.pio_mask	= 0x1f,	/* pio4-0 */
+		.udma_mask	= 0,	/* 0x7f (udma6-0 disabled for now) */
+		.port_ops	= &mv_ops,
+	},
+	{  /* chip_508x */
+		.sht		= &mv_sht,
+		.host_flags	= (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+				   ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO | 
+				   MV_FLAG_DUAL_HC),
+		.pio_mask	= 0x1f,	/* pio4-0 */
+		.udma_mask	= 0,	/* 0x7f (udma6-0 disabled for now) */
+		.port_ops	= &mv_ops,
+	},
+	{  /* chip_604x */
+		.sht		= &mv_sht,
+		.host_flags	= (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+				   ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO | 
+				   MV_FLAG_IRQ_COALESCE | MV_FLAG_BDMA),
+		.pio_mask	= 0x1f,	/* pio4-0 */
+		.udma_mask	= 0,	/* 0x7f (udma6-0 disabled for now) */
+		.port_ops	= &mv_ops,
+	},
+	{  /* chip_608x */
+		.sht		= &mv_sht,
+		.host_flags	= (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+				   ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO |
+				   MV_FLAG_IRQ_COALESCE | MV_FLAG_DUAL_HC |
+				   MV_FLAG_BDMA),
+		.pio_mask	= 0x1f,	/* pio4-0 */
+		.udma_mask	= 0,	/* 0x7f (udma6-0 disabled for now) */
+		.port_ops	= &mv_ops,
+	},
+};
+
+static struct pci_device_id mv_pci_tbl[] = {
+	{PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5040), 0, 0, chip_504x},
+	{PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5041), 0, 0, chip_504x},
+	{PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5080), 0, 0, chip_508x},
+	{PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5081), 0, 0, chip_508x},
+
+	{PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6040), 0, 0, chip_604x},
+	{PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6041), 0, 0, chip_604x},
+	{PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6080), 0, 0, chip_608x},
+	{PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6081), 0, 0, chip_608x},
+	{}			/* terminate list */
+};
+
+static struct pci_driver mv_pci_driver = {
+	.name			= DRV_NAME,
+	.id_table		= mv_pci_tbl,
+	.probe			= mv_init_one,
+	.remove			= ata_pci_remove_one,
+};
+
+/*
+ * Functions
+ */
+
+static inline void writelfl(unsigned long data, void __iomem *addr)
+{
+	writel(data, addr);
+	(void) readl(addr);	/* flush to avoid PCI posted write */
+}
+
+static inline void __iomem *mv_port_addr_to_hc_base(void __iomem *port_mmio)
+{
+	return ((void __iomem *)((unsigned long)port_mmio & 
+				 (unsigned long)SATAHC_MASK));
+}
+
+static inline void __iomem *mv_hc_base(void __iomem *base, unsigned int hc)
+{
+	return (base + MV_SATAHC0_REG_BASE + (hc * MV_SATAHC_REG_SZ));
+}
+
+static inline void __iomem *mv_port_base(void __iomem *base, unsigned int port)
+{
+	return (mv_hc_base(base, port >> MV_PORT_HC_SHIFT) +
+		MV_SATAHC_ARBTR_REG_SZ + 
+		((port & MV_PORT_MASK) * MV_PORT_REG_SZ));
+}
+
+static inline void __iomem *mv_ap_base(struct ata_port *ap)
+{
+	return mv_port_base(ap->host_set->mmio_base, ap->port_no);
+}
+
+static inline int mv_get_hc_count(unsigned long flags)
+{
+	return ((flags & MV_FLAG_DUAL_HC) ? 2 : 1);
+}
+
+static inline int mv_is_edma_active(struct ata_port *ap)
+{
+	void __iomem *port_mmio = mv_ap_base(ap);
+	return (EDMA_EN & readl(port_mmio + EDMA_CMD_OFS));
+}
+
+static inline int mv_port_bdma_capable(struct ata_port *ap)
+{
+	return (ap->flags & MV_FLAG_BDMA);
+}
+
+static void mv_irq_clear(struct ata_port *ap)
+{
+}
+
+static unsigned int mv_scr_offset(unsigned int sc_reg_in)
+{
+	unsigned int ofs;
+
+	switch (sc_reg_in) {
+	case SCR_STATUS:
+	case SCR_CONTROL:
+	case SCR_ERROR:
+		ofs = SATA_STATUS_OFS + (sc_reg_in * sizeof(u32));
+		break;
+	case SCR_ACTIVE:
+		ofs = SATA_ACTIVE_OFS;   /* active is not with the others */
+		break;
+	default:
+		ofs = 0xffffffffU;
+		break;
+	}
+	return ofs;
+}
+
+static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in)
+{
+	unsigned int ofs = mv_scr_offset(sc_reg_in);
+
+	if (0xffffffffU != ofs) {
+		return readl(mv_ap_base(ap) + ofs);
+	} else {
+		return (u32) ofs;
+	}
+}
+
+static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
+{
+	unsigned int ofs = mv_scr_offset(sc_reg_in);
+
+	if (0xffffffffU != ofs) {
+		writelfl(val, mv_ap_base(ap) + ofs);
+	}
+}
+
+static int mv_master_reset(void __iomem *mmio_base)
+{
+	void __iomem *reg = mmio_base + PCI_MAIN_CMD_STS_OFS;
+	int i, rc = 0;
+	u32 t;
+
+	VPRINTK("ENTER\n");
+
+	/* Following procedure defined in PCI "main command and status
+	 * register" table.
+	 */
+	t = readl(reg);
+	writel(t | STOP_PCI_MASTER, reg);
+
+	for (i = 0; i < 100; i++) {
+		msleep(10);
+		t = readl(reg);
+		if (PCI_MASTER_EMPTY & t) {
+			break;
+		}
+	}
+	if (!(PCI_MASTER_EMPTY & t)) {
+		printk(KERN_ERR DRV_NAME "PCI master won't flush\n");
+		rc = 1;		/* broken HW? */
+		goto done;
+	}
+
+	/* set reset */
+	i = 5;
+	do {
+		writel(t | GLOB_SFT_RST, reg);
+		t = readl(reg);
+		udelay(1);
+	} while (!(GLOB_SFT_RST & t) && (i-- > 0));
+
+	if (!(GLOB_SFT_RST & t)) {
+		printk(KERN_ERR DRV_NAME "can't set global reset\n");
+		rc = 1;		/* broken HW? */
+		goto done;
+	}
+
+	/* clear reset */
+	i = 5;
+	do {
+		writel(t & ~GLOB_SFT_RST, reg);
+		t = readl(reg);
+		udelay(1);
+	} while ((GLOB_SFT_RST & t) && (i-- > 0));
+
+	if (GLOB_SFT_RST & t) {
+		printk(KERN_ERR DRV_NAME "can't clear global reset\n");
+		rc = 1;		/* broken HW? */
+	}
+
+ done:
+	VPRINTK("EXIT, rc = %i\n", rc);
+	return rc;
+}
+
+static void mv_err_intr(struct ata_port *ap)
+{
+	void __iomem *port_mmio;
+	u32 edma_err_cause, serr = 0;
+
+	/* bug here b/c we got an err int on a port we don't know about,
+	 * so there's no way to clear it
+	 */
+	BUG_ON(NULL == ap);
+	port_mmio = mv_ap_base(ap);
+
+	edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+
+	if (EDMA_ERR_SERR & edma_err_cause) {
+		serr = scr_read(ap, SCR_ERROR);
+		scr_write_flush(ap, SCR_ERROR, serr);
+	}
+	DPRINTK("port %u error; EDMA err cause: 0x%08x SERR: 0x%08x\n", 
+		ap->port_no, edma_err_cause, serr);
+
+	/* Clear EDMA now that SERR cleanup done */
+	writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+
+	/* check for fatal here and recover if needed */
+	if (EDMA_ERR_FATAL & edma_err_cause) {
+		mv_phy_reset(ap);
+	}
+}
+
+/* Handle any outstanding interrupts in a single SATAHC 
+ */
+static void mv_host_intr(struct ata_host_set *host_set, u32 relevant,
+			 unsigned int hc)
+{
+	void __iomem *mmio = host_set->mmio_base;
+	void __iomem *hc_mmio = mv_hc_base(mmio, hc);
+	struct ata_port *ap;
+	struct ata_queued_cmd *qc;
+	u32 hc_irq_cause;
+	int shift, port, port0, hard_port;
+	u8 ata_status;
+
+	if (hc == 0) {
+		port0 = 0;
+	} else {
+		port0 = MV_PORTS_PER_HC;
+	}
+
+	/* we'll need the HC success int register in most cases */
+	hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
+	if (hc_irq_cause) {
+		writelfl(0, hc_mmio + HC_IRQ_CAUSE_OFS);
+	}
+
+	VPRINTK("ENTER, hc%u relevant=0x%08x HC IRQ cause=0x%08x\n",
+		hc,relevant,hc_irq_cause);
+
+	for (port = port0; port < port0 + MV_PORTS_PER_HC; port++) {
+		ap = host_set->ports[port];
+		hard_port = port & MV_PORT_MASK;	/* range 0-3 */
+		ata_status = 0xffU;
+
+		if (((CRBP_DMA_DONE | DEV_IRQ) << hard_port) & hc_irq_cause) {
+			BUG_ON(NULL == ap);
+			/* rcv'd new resp, basic DMA complete, or ATA IRQ */
+			/* This is needed to clear the ATA INTRQ.
+			 * FIXME: don't read the status reg in EDMA mode!
+			 */
+			ata_status = readb((void __iomem *)
+					   ap->ioaddr.status_addr);
+		}
+
+		shift = port * 2;
+		if (port >= MV_PORTS_PER_HC) {
+			shift++;	/* skip bit 8 in the HC Main IRQ reg */
+		}
+		if ((PORT0_ERR << shift) & relevant) {
+			mv_err_intr(ap);
+			/* FIXME: smart to OR in ATA_ERR? */
+			ata_status = readb((void __iomem *)
+					   ap->ioaddr.status_addr) | ATA_ERR;
+		}
+		
+		if (ap) {
+			qc = ata_qc_from_tag(ap, ap->active_tag);
+			if (NULL != qc) {
+				VPRINTK("port %u IRQ found for qc, "
+					"ata_status 0x%x\n", port,ata_status);
+				BUG_ON(0xffU == ata_status);
+				/* mark qc status appropriately */
+				ata_qc_complete(qc, ata_status);
+			}
+		}
+	}
+	VPRINTK("EXIT\n");
+}
+
+static irqreturn_t mv_interrupt(int irq, void *dev_instance,
+				struct pt_regs *regs)
+{
+	struct ata_host_set *host_set = dev_instance;
+	unsigned int hc, handled = 0, n_hcs;
+	void __iomem *mmio;
+	u32 irq_stat;
+
+	mmio = host_set->mmio_base;
+	irq_stat = readl(mmio + HC_MAIN_IRQ_CAUSE_OFS);
+	n_hcs = mv_get_hc_count(host_set->ports[0]->flags);
+
+	/* check the cases where we either have nothing pending or have read
+	 * a bogus register value which can indicate HW removal or PCI fault
+	 */
+	if (!irq_stat || (0xffffffffU == irq_stat)) {
+		return IRQ_NONE;
+	}
+
+	spin_lock(&host_set->lock);
+
+	for (hc = 0; hc < n_hcs; hc++) {
+		u32 relevant = irq_stat & (HC0_IRQ_PEND << (hc * HC_SHIFT));
+		if (relevant) {
+			mv_host_intr(host_set, relevant, hc);
+			handled = 1;
+		}
+	}
+	if (PCI_ERR & irq_stat) {
+		/* FIXME: these are all masked by default, but still need
+		 * to recover from them properly.
+		 */
+	}
+
+	spin_unlock(&host_set->lock);
+
+	return IRQ_RETVAL(handled);
+}
+
+static void mv_phy_reset(struct ata_port *ap)
+{
+	void __iomem *port_mmio = mv_ap_base(ap);
+	struct ata_taskfile tf;
+	struct ata_device *dev = &ap->device[0];
+	u32 edma = 0, bdma;
+
+	VPRINTK("ENTER, port %u, mmio 0x%p\n", ap->port_no, port_mmio);
+
+	edma = readl(port_mmio + EDMA_CMD_OFS);
+	if (EDMA_EN & edma) {
+		/* disable EDMA if active */
+		edma &= ~EDMA_EN;
+		writelfl(edma | EDMA_DS, port_mmio + EDMA_CMD_OFS);
+		udelay(1);
+	} else if (mv_port_bdma_capable(ap) &&
+		   (bdma = readl(port_mmio + BDMA_CMD_OFS)) & BDMA_START) {
+		/* disable BDMA if active */
+		writelfl(bdma & ~BDMA_START, port_mmio + BDMA_CMD_OFS);
+	}
+
+	writelfl(edma | ATA_RST, port_mmio + EDMA_CMD_OFS);
+	udelay(25);		/* allow reset propagation */
+
+	/* Spec never mentions clearing the bit.  Marvell's driver does
+	 * clear the bit, however.
+	 */
+	writelfl(edma & ~ATA_RST, port_mmio + EDMA_CMD_OFS);
+
+	VPRINTK("Done.  Now calling __sata_phy_reset()\n");
+
+	/* proceed to init communications via the scr_control reg */
+	__sata_phy_reset(ap);
+
+	if (ap->flags & ATA_FLAG_PORT_DISABLED) {
+		VPRINTK("Port disabled pre-sig.  Exiting.\n");
+		return;
+	}
+
+	tf.lbah = readb((void __iomem *) ap->ioaddr.lbah_addr);
+	tf.lbam = readb((void __iomem *) ap->ioaddr.lbam_addr);
+	tf.lbal = readb((void __iomem *) ap->ioaddr.lbal_addr);
+	tf.nsect = readb((void __iomem *) ap->ioaddr.nsect_addr);
+
+	dev->class = ata_dev_classify(&tf);
+	if (!ata_dev_present(dev)) {
+		VPRINTK("Port disabled post-sig: No device present.\n");
+		ata_port_disable(ap);
+	}
+	VPRINTK("EXIT\n");
+}
+
+static void mv_port_init(struct ata_ioports *port, unsigned long base)
+{
+	/* PIO related setup */
+	port->data_addr = base + SHD_PIO_DATA_OFS;
+	port->error_addr = port->feature_addr = base + SHD_FEA_ERR_OFS;
+	port->nsect_addr = base + SHD_SECT_CNT_OFS;
+	port->lbal_addr = base + SHD_LBA_L_OFS;
+	port->lbam_addr = base + SHD_LBA_M_OFS;
+	port->lbah_addr = base + SHD_LBA_H_OFS;
+	port->device_addr = base + SHD_DEV_HD_OFS;
+	port->status_addr = port->command_addr = base + SHD_CMD_STA_OFS;
+	port->altstatus_addr = port->ctl_addr = base + SHD_CTL_AST_OFS;
+	/* unused */
+	port->cmd_addr = port->bmdma_addr = port->scr_addr = 0;
+
+	/* unmask all EDMA error interrupts */
+	writel(~0, (void __iomem *)base + EDMA_ERR_IRQ_MASK_OFS);
+
+	VPRINTK("EDMA cfg=0x%08x EDMA IRQ err cause/mask=0x%08x/0x%08x\n", 
+		readl((void __iomem *)base + EDMA_CFG_OFS),
+		readl((void __iomem *)base + EDMA_ERR_IRQ_CAUSE_OFS),
+		readl((void __iomem *)base + EDMA_ERR_IRQ_MASK_OFS));
+}
+
+static int mv_host_init(struct ata_probe_ent *probe_ent)
+{
+	int rc = 0, n_hc, port, hc;
+	void __iomem *mmio = probe_ent->mmio_base;
+	void __iomem *port_mmio;
+
+	if (mv_master_reset(probe_ent->mmio_base)) {
+		rc = 1;
+		goto done;
+	}
+
+	n_hc = mv_get_hc_count(probe_ent->host_flags);
+	probe_ent->n_ports = MV_PORTS_PER_HC * n_hc;
+
+	for (port = 0; port < probe_ent->n_ports; port++) {
+		port_mmio = mv_port_base(mmio, port);
+		mv_port_init(&probe_ent->port[port], (unsigned long)port_mmio);
+	}
+
+	for (hc = 0; hc < n_hc; hc++) {
+		VPRINTK("HC%i: HC config=0x%08x HC IRQ cause=0x%08x\n", hc,
+			readl(mv_hc_base(mmio, hc) + HC_CFG_OFS),
+			readl(mv_hc_base(mmio, hc) + HC_IRQ_CAUSE_OFS));
+	}
+
+	writel(~HC_MAIN_MASKED_IRQS, mmio + HC_MAIN_IRQ_MASK_OFS);
+	writel(PCI_UNMASK_ALL_IRQS, mmio + PCI_IRQ_MASK_OFS);
+
+	VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x "
+		"PCI int cause/mask=0x%08x/0x%08x\n", 
+		readl(mmio + HC_MAIN_IRQ_CAUSE_OFS),
+		readl(mmio + HC_MAIN_IRQ_MASK_OFS),
+		readl(mmio + PCI_IRQ_CAUSE_OFS),
+		readl(mmio + PCI_IRQ_MASK_OFS));
+
+ done:
+	return rc;
+}
+
+static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+	static int printed_version = 0;
+	struct ata_probe_ent *probe_ent = NULL;
+	struct mv_host_priv *hpriv;
+	unsigned int board_idx = (unsigned int)ent->driver_data;
+	void __iomem *mmio_base;
+	int pci_dev_busy = 0;
+	int rc;
+
+	if (!printed_version++) {
+		printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+	}
+
+	VPRINTK("ENTER for PCI Bus:Slot.Func=%u:%u.%u\n", pdev->bus->number,
+		PCI_SLOT(pdev->devfn), PCI_FUNC(pdev->devfn));
+
+	rc = pci_enable_device(pdev);
+	if (rc) {
+		return rc;
+	}
+
+	rc = pci_request_regions(pdev, DRV_NAME);
+	if (rc) {
+		pci_dev_busy = 1;
+		goto err_out;
+	}
+
+	pci_intx(pdev, 1);
+
+	probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL);
+	if (probe_ent == NULL) {
+		rc = -ENOMEM;
+		goto err_out_regions;
+	}
+
+	memset(probe_ent, 0, sizeof(*probe_ent));
+	probe_ent->dev = pci_dev_to_dev(pdev);
+	INIT_LIST_HEAD(&probe_ent->node);
+
+	mmio_base = ioremap_nocache(pci_resource_start(pdev, MV_PRIMARY_BAR),
+				    pci_resource_len(pdev, MV_PRIMARY_BAR));
+	if (mmio_base == NULL) {
+		rc = -ENOMEM;
+		goto err_out_free_ent;
+	}
+
+	hpriv = kmalloc(sizeof(*hpriv), GFP_KERNEL);
+	if (!hpriv) {
+		rc = -ENOMEM;
+		goto err_out_iounmap;
+	}
+	memset(hpriv, 0, sizeof(*hpriv));
+
+	probe_ent->sht = mv_port_info[board_idx].sht;
+	probe_ent->host_flags = mv_port_info[board_idx].host_flags;
+	probe_ent->pio_mask = mv_port_info[board_idx].pio_mask;
+	probe_ent->udma_mask = mv_port_info[board_idx].udma_mask;
+	probe_ent->port_ops = mv_port_info[board_idx].port_ops;
+
+	probe_ent->irq = pdev->irq;
+	probe_ent->irq_flags = SA_SHIRQ;
+	probe_ent->mmio_base = mmio_base;
+	probe_ent->private_data = hpriv;
+
+	/* initialize adapter */
+	rc = mv_host_init(probe_ent);
+	if (rc) {
+		goto err_out_hpriv;
+	}
+/* 	mv_print_info(probe_ent); */
+
+	{
+		int b, w;
+		u32 dw[4];	/* hold a line of 16b */
+		VPRINTK("PCI config space:\n");
+		for (b = 0; b < 0x40; ) {
+			for (w = 0; w < 4; w++) {
+				(void) pci_read_config_dword(pdev,b,&dw[w]);
+				b += sizeof(*dw);
+			}
+			VPRINTK("%08x %08x %08x %08x\n",
+				dw[0],dw[1],dw[2],dw[3]);
+		}
+	}
+
+	/* FIXME: check ata_device_add return value */
+	ata_device_add(probe_ent);
+	kfree(probe_ent);
+
+	return 0;
+
+ err_out_hpriv:
+	kfree(hpriv);
+ err_out_iounmap:
+	iounmap(mmio_base);
+ err_out_free_ent:
+	kfree(probe_ent);
+ err_out_regions:
+	pci_release_regions(pdev);
+ err_out:
+	if (!pci_dev_busy) {
+		pci_disable_device(pdev);
+	}
+
+	return rc;
+}
+
+static int __init mv_init(void)
+{
+	return pci_module_init(&mv_pci_driver);
+}
+
+static void __exit mv_exit(void)
+{
+	pci_unregister_driver(&mv_pci_driver);
+}
+
+MODULE_AUTHOR("Brett Russ");
+MODULE_DESCRIPTION("SCSI low-level driver for Marvell SATA controllers");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, mv_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(mv_init);
+module_exit(mv_exit);