Commit 26f31fb9 authored by Linus Torvalds's avatar Linus Torvalds

Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 - New drivers for ADC128D818, LTC2945, LTC4260, and LTC4222
 - Added support for LTM4676 to ltc2978 driver
 - Converted several drivers to use devm_hwmon_device_register_with_groups
 - Various cleanup in several drivers

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (36 commits)
  hwmon: (pmbus/ltc2978) Add support for LTM4676
  hwmon: (pmbus/ltc2978) Add new chip ID for LTC2974
  hwmon: Do not accept invalid name attributes
  hwmon: (max6639) Use SIMPLE_DEV_PM_OPS macro
  hwmon: (lm95245) Make temp2_crit_hyst read-only
  hwmon: (lm95245) Convert to use devm_hwmon_device_register_with_groups
  hwmon: (lm95245) Drop useless debug message
  hwmon: (lm95245) Fix hysteresis temperatures
  hwmon: (max6639) Convert to use devm_hwmon_device_register_with_groups
  hwmon: (max6639) Introduce local dev variable, and reduce noisiness
  hwmon: (max6650) Introduce local 'dev' variable
  hwmon: (max6650) Drop error message after memory allocation failures
  hwmon: (max6650) Convert to use devm_hwmon_device_register_with_groups
  hwmon: (max6650) Rearrange code to no longer require forward declarations
  hwmon: (ltc4215) Convert to devm_hwmon_device_register_with_groups
  hwmon: (coretemp) Convert to use devm_hwmon_device_register_with_groups
  hwmon: (coretemp) Allocate platform data with devm_kzalloc
  hwmon: (coretemp) Use sysfs_create_group to create sysfs attributes
  hwmon: (ltc4245) Remove devicetree conditionals
  hwmon: (ltc4245) Drop debug messages
  ...
parents 0c8cfbad f76992b0
Kernel driver adc128d818
========================
Supported chips:
* Texas Instruments ADC818D818
Prefix: 'adc818d818'
Addresses scanned: I2C 0x1d, 0x1e, 0x1f, 0x2d, 0x2e, 0x2f
Datasheet: Publicly available at the TI website
http://www.ti.com/
Author: Guenter Roeck
Description
-----------
This driver implements support for the Texas Instruments ADC128D818.
It is described as 'ADC System Monitor with Temperature Sensor'.
The ADC128D818 implements one temperature sensor and seven voltage sensors.
Temperatures are measured in degrees Celsius. There is one set of limits.
When the HOT Temperature Limit is crossed, this will cause an alarm that will
be reasserted until the temperature drops below the HOT Hysteresis.
Measurements are guaranteed between -55 and +125 degrees. The temperature
measurement has a resolution of 0.5 degrees; the limits have a resolution
of 1 degree.
Voltage sensors (also known as IN sensors) report their values in volts.
An alarm is triggered if the voltage has crossed a programmable minimum
or maximum limit. Note that minimum in this case always means 'closest to
zero'; this is important for negative voltage measurements. All voltage
inputs can measure voltages between 0 and 2.55 volts, with a resolution
of 0.625 mV.
If an alarm triggers, it will remain triggered until the hardware register
is read at least once. This means that the cause for the alarm may
already have disappeared by the time the alarm is read. The driver
caches the alarm status for each sensor until it is at least reported
once, to ensure that alarms are reported to user space.
The ADC128D818 only updates its values approximately once per second;
reading it more often will do no harm, but will return 'old' values.
In addition to the scanned address list, the chip can also be configured for
addresses 0x35 to 0x37. Those addresses are not scanned. You have to instantiate
the driver explicitly if the chip is configured for any of those addresses in
your system.
......@@ -24,8 +24,12 @@ is given within a range of -127 to +127.875 degrees. Remote temperatures are
given within a range of -127 to +255 degrees. Resolution depends on
temperature input and range.
Each sensor has its own critical limit, but the hysteresis is common to all
two channels.
Each sensor has its own critical limit. Additionally, there is a relative
hysteresis value common to both critical limits. To make life easier to
user-space applications, two absolute values are exported, one for each
channel, but these values are of course linked. Only the local hysteresis
can be set from user-space, and the same delta applies to the remote
hysteresis.
The lm95245 driver can change its update interval to a fixed set of values.
It will round up to the next selectable interval. See the datasheet for exact
......
Kernel driver ltc2945
=====================
Supported chips:
* Linear Technology LTC2945
Prefix: 'ltc2945'
Addresses scanned: -
Datasheet:
http://cds.linear.com/docs/en/datasheet/2945fa.pdf
Author: Guenter Roeck <linux@roeck-us.net>
Description
-----------
The LTC2945 is a rail-to-rail system monitor that measures current, voltage,
and power consumption.
Usage Notes
-----------
This driver does not probe for LTC2945 devices, since there is no register
which can be safely used to identify the chip. You will have to instantiate
the devices explicitly.
Example: the following will load the driver for an LTC2945 at address 0x10
on I2C bus #1:
$ modprobe ltc2945
$ echo ltc2945 0x10 > /sys/bus/i2c/devices/i2c-1/new_device
Sysfs entries
-------------
Voltage readings provided by this driver are reported as obtained from the ADC
registers. If a set of voltage divider resistors is installed, calculate the
real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the
value of the divider resistor against the measured voltage and R2 is the value
of the divider resistor against Ground.
Current reading provided by this driver is reported as obtained from the ADC
Current Sense register. The reported value assumes that a 1 mOhm sense resistor
is installed. If a different sense resistor is installed, calculate the real
current by dividing the reported value by the sense resistor value in mOhm.
in1_input VIN voltage (mV). Voltage is measured either at
SENSE+ or VDD pin depending on chip configuration.
in1_min Undervoltage threshold
in1_max Overvoltage threshold
in1_lowest Lowest measured voltage
in1_highest Highest measured voltage
in1_reset_history Write 1 to reset in1 history
in1_min_alarm Undervoltage alarm
in1_max_alarm Overvoltage alarm
in2_input ADIN voltage (mV)
in2_min Undervoltage threshold
in2_max Overvoltage threshold
in2_lowest Lowest measured voltage
in2_highest Highest measured voltage
in2_reset_history Write 1 to reset in2 history
in2_min_alarm Undervoltage alarm
in2_max_alarm Overvoltage alarm
curr1_input SENSE current (mA)
curr1_min Undercurrent threshold
curr1_max Overcurrent threshold
curr1_lowest Lowest measured current
curr1_highest Highest measured current
curr1_reset_history Write 1 to reset curr1 history
curr1_min_alarm Undercurrent alarm
curr1_max_alarm Overcurrent alarm
power1_input Power (in uW). Power is calculated based on SENSE+/VDD
voltage or ADIN voltage depending on chip configuration.
power1_min Low lower threshold
power1_max High power threshold
power1_input_lowest Historical minimum power use
power1_input_highest Historical maximum power use
power1_reset_history Write 1 to reset power1 history
power1_min_alarm Low power alarm
power1_max_alarm High power alarm
......@@ -23,6 +23,10 @@ Supported chips:
Prefix: 'ltc3883'
Addresses scanned: -
Datasheet: http://www.linear.com/product/ltc3883
* Linear Technology LTM4676
Prefix: 'ltm4676'
Addresses scanned: -
Datasheet: http://www.linear.com/product/ltm4676
Author: Guenter Roeck <linux@roeck-us.net>
......@@ -33,7 +37,8 @@ Description
LTC2974 is a quad digital power supply manager. LTC2978 is an octal power supply
monitor. LTC2977 is a pin compatible replacement for LTC2978. LTC3880 is a dual
output poly-phase step-down DC/DC controller. LTC3883 is a single phase
step-down DC/DC controller.
step-down DC/DC controller. LTM4676 is a dual 13A or single 26A uModule
regulator.
Usage Notes
......@@ -75,7 +80,7 @@ in[N]_label "vout[1-8]".
LTC2974: N=2-5
LTC2977: N=2-9
LTC2978: N=2-9
LTC3880: N=2-3
LTC3880, LTM4676: N=2-3
LTC3883: N=2
in[N]_input Measured output voltage.
in[N]_min Minimum output voltage.
......@@ -95,7 +100,7 @@ temp[N]_input Measured temperature.
and temp5 reports the chip temperature.
On LTC2977 and LTC2978, only one temperature measurement
is supported and reports the chip temperature.
On LTC3880, temp1 and temp2 report external
On LTC3880 and LTM4676, temp1 and temp2 report external
temperatures, and temp3 reports the chip temperature.
On LTC3883, temp1 reports an external temperature,
and temp2 reports the chip temperature.
......@@ -123,11 +128,11 @@ power[N]_label "pout[1-4]".
LTC2974: N=1-4
LTC2977: Not supported
LTC2978: Not supported
LTC3880: N=1-2
LTC3880, LTM4676: N=1-2
LTC3883: N=2
power[N]_input Measured output power.
curr1_label "iin". LTC3880 and LTC3883 only.
curr1_label "iin". LTC3880, LTC3883, and LTM4676 only.
curr1_input Measured input current.
curr1_max Maximum input current.
curr1_max_alarm Input current high alarm.
......@@ -138,7 +143,7 @@ curr[N]_label "iout[1-4]".
LTC2974: N=1-4
LTC2977: not supported
LTC2978: not supported
LTC3880: N=2-3
LTC3880, LTM4676: N=2-3
LTC3883: N=2
curr[N]_input Measured output current.
curr[N]_max Maximum output current.
......
Kernel driver ltc4260
=====================
Supported chips:
* Linear Technology LTC4260
Prefix: 'ltc4260'
Addresses scanned: -
Datasheet:
http://cds.linear.com/docs/en/datasheet/4260fc.pdf
Author: Guenter Roeck <linux@roeck-us.net>
Description
-----------
The LTC4260 Hot Swap controller allows a board to be safely inserted
and removed from a live backplane.
Usage Notes
-----------
This driver does not probe for LTC4260 devices, since there is no register
which can be safely used to identify the chip. You will have to instantiate
the devices explicitly.
Example: the following will load the driver for an LTC4260 at address 0x10
on I2C bus #1:
$ modprobe ltc4260
$ echo ltc4260 0x10 > /sys/bus/i2c/devices/i2c-1/new_device
Sysfs entries
-------------
Voltage readings provided by this driver are reported as obtained from the ADC
registers. If a set of voltage divider resistors is installed, calculate the
real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the
value of the divider resistor against the measured voltage and R2 is the value
of the divider resistor against Ground.
Current reading provided by this driver is reported as obtained from the ADC
Current Sense register. The reported value assumes that a 1 mOhm sense resistor
is installed. If a different sense resistor is installed, calculate the real
current by dividing the reported value by the sense resistor value in mOhm.
in1_input SOURCE voltage (mV)
in1_min_alarm Undervoltage alarm
in1_max_alarm Overvoltage alarm
in2_input ADIN voltage (mV)
in2_alarm Power bad alarm
curr1_input SENSE current (mA)
curr1_alarm SENSE overcurrent alarm
......@@ -111,22 +111,6 @@ config SENSORS_AD7418
This driver can also be built as a module. If so, the module
will be called ad7418.
config SENSORS_ADCXX
tristate "National Semiconductor ADCxxxSxxx"
depends on SPI_MASTER
help
If you say yes here you get support for the National Semiconductor
ADC<bb><c>S<sss> chip family, where
* bb is the resolution in number of bits (8, 10, 12)
* c is the number of channels (1, 2, 4, 8)
* sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
kSPS and 101 for 1 MSPS)
Examples : ADC081S101, ADC124S501, ...
This driver can also be built as a module. If so, the module
will be called adcxx.
config SENSORS_ADM1021
tristate "Analog Devices ADM1021 and compatibles"
depends on I2C
......@@ -312,6 +296,31 @@ config SENSORS_FAM15H_POWER
This driver can also be built as a module. If so, the module
will be called fam15h_power.
config SENSORS_APPLESMC
tristate "Apple SMC (Motion sensor, light sensor, keyboard backlight)"
depends on INPUT && X86
select NEW_LEDS
select LEDS_CLASS
select INPUT_POLLDEV
default n
help
This driver provides support for the Apple System Management
Controller, which provides an accelerometer (Apple Sudden Motion
Sensor), light sensors, temperature sensors, keyboard backlight
control and fan control.
Only Intel-based Apple's computers are supported (MacBook Pro,
MacBook, MacMini).
Data from the different sensors, keyboard backlight control and fan
control are accessible via sysfs.
This driver also provides an absolute input class device, allowing
the laptop to act as a pinball machine-esque joystick.
Say Y here if you have an applicable laptop and want to experience
the awesome power of applesmc.
config SENSORS_ASB100
tristate "Asus ASB100 Bach"
depends on X86 && I2C
......@@ -435,6 +444,12 @@ config SENSORS_F75375S
This driver can also be built as a module. If so, the module
will be called f75375s.
config SENSORS_MC13783_ADC
tristate "Freescale MC13783/MC13892 ADC"
depends on MFD_MC13XXX
help
Support for the A/D converter on MC13783 and MC13892 PMIC.
config SENSORS_FSCHMD
tristate "Fujitsu Siemens Computers sensor chips"
depends on X86 && I2C
......@@ -451,26 +466,6 @@ config SENSORS_FSCHMD
This driver can also be built as a module. If so, the module
will be called fschmd.
config SENSORS_G760A
tristate "GMT G760A"
depends on I2C
help
If you say yes here you get support for Global Mixed-mode
Technology Inc G760A fan speed PWM controller chips.
This driver can also be built as a module. If so, the module
will be called g760a.
config SENSORS_G762
tristate "GMT G762 and G763"
depends on I2C
help
If you say yes here you get support for Global Mixed-mode
Technology Inc G762 and G763 fan speed PWM controller chips.
This driver can also be built as a module. If so, the module
will be called g762.
config SENSORS_GL518SM
tristate "Genesys Logic GL518SM"
depends on I2C
......@@ -492,6 +487,26 @@ config SENSORS_GL520SM
This driver can also be built as a module. If so, the module
will be called gl520sm.
config SENSORS_G760A
tristate "GMT G760A"
depends on I2C
help
If you say yes here you get support for Global Mixed-mode
Technology Inc G760A fan speed PWM controller chips.
This driver can also be built as a module. If so, the module
will be called g760a.
config SENSORS_G762
tristate "GMT G762 and G763"
depends on I2C
help
If you say yes here you get support for Global Mixed-mode
Technology Inc G762 and G763 fan speed PWM controller chips.
This driver can also be built as a module. If so, the module
will be called g762.
config SENSORS_GPIO_FAN
tristate "GPIO fan"
depends on GPIOLIB
......@@ -511,24 +526,6 @@ config SENSORS_HIH6130
This driver can also be built as a module. If so, the module
will be called hih6130.
config SENSORS_HTU21
tristate "Measurement Specialties HTU21D humidity/temperature sensors"
depends on I2C
help
If you say yes here you get support for the Measurement Specialties
HTU21D humidity and temperature sensors.
This driver can also be built as a module. If so, the module
will be called htu21.
config SENSORS_CORETEMP
tristate "Intel Core/Core2/Atom temperature sensor"
depends on X86
help
If you say yes here you get support for the temperature
sensor inside your CPU. Most of the family 6 CPUs
are supported. Check Documentation/hwmon/coretemp for details.
config SENSORS_IBMAEM
tristate "IBM Active Energy Manager temperature/power sensors and control"
select IPMI_SI
......@@ -566,6 +563,14 @@ config SENSORS_IIO_HWMON
for those channels specified in the map. This map can be provided
either via platform data or the device tree bindings.
config SENSORS_CORETEMP
tristate "Intel Core/Core2/Atom temperature sensor"
depends on X86
help
If you say yes here you get support for the temperature
sensor inside your CPU. Most of the family 6 CPUs
are supported. Check Documentation/hwmon/coretemp for details.
config SENSORS_IT87
tristate "ITE IT87xx and compatibles"
depends on !PPC
......@@ -614,374 +619,409 @@ config SENSORS_LINEAGE
This driver can also be built as a module. If so, the module
will be called lineage-pem.
config SENSORS_LM63
tristate "National Semiconductor LM63 and compatibles"
config SENSORS_LTC2945
tristate "Linear Technology LTC2945"
depends on I2C
select REGMAP_I2C
default n
help
If you say yes here you get support for the National
Semiconductor LM63, LM64, and LM96163 remote diode digital temperature
sensors with integrated fan control. Such chips are found
on the Tyan S4882 (Thunder K8QS Pro) motherboard, among
others.
If you say yes here you get support for Linear Technology LTC2945
I2C System Monitor.
This driver can also be built as a module. If so, the module
will be called lm63.
This driver can also be built as a module. If so, the module will
be called ltc2945.
config SENSORS_LM70
tristate "National Semiconductor LM70 and compatibles"
depends on SPI_MASTER
config SENSORS_LTC4151
tristate "Linear Technology LTC4151"
depends on I2C
default n
help
If you say yes here you get support for the National Semiconductor
LM70, LM71, LM74 and Texas Instruments TMP121/TMP123 digital tempera-
ture sensor chips.
If you say yes here you get support for Linear Technology LTC4151
High Voltage I2C Current and Voltage Monitor interface.
This driver can also be built as a module. If so, the module
will be called lm70.
This driver can also be built as a module. If so, the module will
be called ltc4151.
config SENSORS_LM73
tristate "National Semiconductor LM73"
config SENSORS_LTC4215
tristate "Linear Technology LTC4215"
depends on I2C
default n
help
If you say yes here you get support for National Semiconductor LM73
sensor chips.
This driver can also be built as a module. If so, the module
will be called lm73.
If you say yes here you get support for Linear Technology LTC4215
Hot Swap Controller I2C interface.
config SENSORS_LM75
tristate "National Semiconductor LM75 and compatibles"
This driver can also be built as a module. If so, the module will
be called ltc4215.
config SENSORS_LTC4222
tristate "Linear Technology LTC4222"
depends on I2C
depends on THERMAL || !THERMAL_OF
select REGMAP_I2C
default n
help
If you say yes here you get support for one common type of
temperature sensor chip, with models including:
If you say yes here you get support for Linear Technology LTC4222
Dual Hot Swap Controller I2C interface.
- Analog Devices ADT75
- Dallas Semiconductor DS75, DS1775 and DS7505
- Global Mixed-mode Technology (GMT) G751
- Maxim MAX6625 and MAX6626
- Microchip MCP980x
- National Semiconductor LM75, LM75A
- NXP's LM75A
- ST Microelectronics STDS75
- TelCom (now Microchip) TCN75
- Texas Instruments TMP100, TMP101, TMP105, TMP75, TMP175,
TMP275
This driver can also be built as a module. If so, the module will
be called ltc4222.
This driver supports driver model based binding through board
specific I2C device tables.
config SENSORS_LTC4245
tristate "Linear Technology LTC4245"
depends on I2C
default n
help
If you say yes here you get support for Linear Technology LTC4245
Multiple Supply Hot Swap Controller I2C interface.
It also supports the "legacy" style of driver binding. To use
that with some chips which don't replicate LM75 quirks exactly,
you may need the "force" module parameter.
This driver can also be built as a module. If so, the module will
be called ltc4245.
This driver can also be built as a module. If so, the module
will be called lm75.
config SENSORS_LTC4260
tristate "Linear Technology LTC4260"
depends on I2C
select REGMAP_I2C
default n
help
If you say yes here you get support for Linear Technology LTC4260
Positive Voltage Hot Swap Controller I2C interface.
config SENSORS_LM77
tristate "National Semiconductor LM77"
This driver can also be built as a module. If so, the module will
be called ltc4260.
config SENSORS_LTC4261
tristate "Linear Technology LTC4261"
depends on I2C
default n
help
If you say yes here you get support for National Semiconductor LM77
sensor chips.
If you say yes here you get support for Linear Technology LTC4261
Negative Voltage Hot Swap Controller I2C interface.
This driver can also be built as a module. If so, the module will
be called ltc4261.
config SENSORS_MAX1111
tristate "Maxim MAX1111 Serial 8-bit ADC chip and compatibles"
depends on SPI_MASTER
help
Say y here to support Maxim's MAX1110, MAX1111, MAX1112, and MAX1113
ADC chips.
This driver can also be built as a module. If so, the module
will be called lm77.
will be called max1111.
config SENSORS_LM78
tristate "National Semiconductor LM78 and compatibles"
config SENSORS_MAX16065
tristate "Maxim MAX16065 System Manager and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM78,
LM78-J and LM79.
If you say yes here you get support for hardware monitoring
capabilities of the following Maxim System Manager chips.
MAX16065
MAX16066
MAX16067
MAX16068
MAX16070
MAX16071
This driver can also be built as a module. If so, the module
will be called lm78.
will be called max16065.
config SENSORS_LM80
tristate "National Semiconductor LM80 and LM96080"
config SENSORS_MAX1619
tristate "Maxim MAX1619 sensor chip"
depends on I2C
help
If you say yes here you get support for National Semiconductor
LM80 and LM96080 sensor chips.
If you say yes here you get support for MAX1619 sensor chip.
This driver can also be built as a module. If so, the module
will be called lm80.
will be called max1619.
config SENSORS_LM83
tristate "National Semiconductor LM83 and compatibles"
config SENSORS_MAX1668
tristate "Maxim MAX1668 and compatibles"
depends on I2C
help
If you say yes here you get support for National Semiconductor
LM82 and LM83 sensor chips.
If you say yes here you get support for MAX1668, MAX1989 and
MAX1805 chips.
This driver can also be built as a module. If so, the module
will be called lm83.
will be called max1668.
config SENSORS_LM85
tristate "National Semiconductor LM85 and compatibles"
config SENSORS_MAX197
tristate "Maxim MAX197 and compatibles"
help
Support for the Maxim MAX197 A/D converter.
Support will include, but not be limited to, MAX197, and MAX199.
This driver can also be built as a module. If so, the module
will be called max197.
config SENSORS_MAX6639
tristate "Maxim MAX6639 sensor chip"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM85
sensor chips and clones: ADM1027, ADT7463, ADT7468, EMC6D100,
EMC6D101, EMC6D102, and EMC6D103.
If you say yes here you get support for the MAX6639
sensor chips.
This driver can also be built as a module. If so, the module
will be called lm85.
will be called max6639.
config SENSORS_LM87
tristate "National Semiconductor LM87 and compatibles"
config SENSORS_MAX6642
tristate "Maxim MAX6642 sensor chip"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM87
and Analog Devices ADM1024 sensor chips.
If you say yes here you get support for MAX6642 sensor chip.
MAX6642 is a SMBus-Compatible Remote/Local Temperature Sensor
with Overtemperature Alarm from Maxim.
This driver can also be built as a module. If so, the module
will be called lm87.
will be called max6642.
config SENSORS_LM90
tristate "National Semiconductor LM90 and compatibles"
config SENSORS_MAX6650
tristate "Maxim MAX6650 sensor chip"
depends on I2C
help
If you say yes here you get support for National Semiconductor LM90,
LM86, LM89 and LM99, Analog Devices ADM1032, ADT7461, and ADT7461A,
Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6657, MAX6658, MAX6659,
MAX6680, MAX6681, MAX6692, MAX6695, MAX6696, ON Semiconductor NCT1008,
Winbond/Nuvoton W83L771W/G/AWG/ASG, Philips SA56004, and GMT G781
If you say yes here you get support for the MAX6650 / MAX6651
sensor chips.
This driver can also be built as a module. If so, the module
will be called lm90.
will be called max6650.
config SENSORS_LM92
tristate "National Semiconductor LM92 and compatibles"
config SENSORS_MAX6697
tristate "Maxim MAX6697 and compatibles"
depends on I2C
help
If you say yes here you get support for National Semiconductor LM92
and Maxim MAX6635 sensor chips.
If you say yes here you get support for MAX6581, MAX6602, MAX6622,
MAX6636, MAX6689, MAX6693, MAX6694, MAX6697, MAX6698, and MAX6699
temperature sensor chips.
This driver can also be built as a module. If so, the module
will be called lm92.
will be called max6697.
config SENSORS_LM93
tristate "National Semiconductor LM93 and compatibles"
config SENSORS_HTU21
tristate "Measurement Specialties HTU21D humidity/temperature sensors"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM93,
LM94, and compatible sensor chips.
If you say yes here you get support for the Measurement Specialties
HTU21D humidity and temperature sensors.
This driver can also be built as a module. If so, the module
will be called lm93.
will be called htu21.
config SENSORS_LTC4151
tristate "Linear Technology LTC4151"
config SENSORS_MCP3021
tristate "Microchip MCP3021 and compatibles"
depends on I2C
default n
help
If you say yes here you get support for Linear Technology LTC4151
High Voltage I2C Current and Voltage Monitor interface.
If you say yes here you get support for MCP3021 and MCP3221.
The MCP3021 is a A/D converter (ADC) with 10-bit and the MCP3221
with 12-bit resolution.
This driver can also be built as a module. If so, the module will
be called ltc4151.
This driver can also be built as a module. If so, the module
will be called mcp3021.
config SENSORS_LTC4215
tristate "Linear Technology LTC4215"
depends on I2C
default n
config SENSORS_ADCXX
tristate "National Semiconductor ADCxxxSxxx"
depends on SPI_MASTER
help
If you say yes here you get support for Linear Technology LTC4215
Hot Swap Controller I2C interface.
If you say yes here you get support for the National Semiconductor
ADC<bb><c>S<sss> chip family, where
* bb is the resolution in number of bits (8, 10, 12)
* c is the number of channels (1, 2, 4, 8)
* sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
kSPS and 101 for 1 MSPS)
This driver can also be built as a module. If so, the module will
be called ltc4215.
Examples : ADC081S101, ADC124S501, ...
config SENSORS_LTC4245
tristate "Linear Technology LTC4245"
This driver can also be built as a module. If so, the module
will be called adcxx.
config SENSORS_LM63
tristate "National Semiconductor LM63 and compatibles"
depends on I2C
default n
help
If you say yes here you get support for Linear Technology LTC4245
Multiple Supply Hot Swap Controller I2C interface.
If you say yes here you get support for the National
Semiconductor LM63, LM64, and LM96163 remote diode digital temperature
sensors with integrated fan control. Such chips are found
on the Tyan S4882 (Thunder K8QS Pro) motherboard, among
others.
This driver can also be built as a module. If so, the module will
be called ltc4245.
This driver can also be built as a module. If so, the module
will be called lm63.
config SENSORS_LTC4261
tristate "Linear Technology LTC4261"
depends on I2C
default n
config SENSORS_LM70
tristate "National Semiconductor LM70 and compatibles"
depends on SPI_MASTER
help
If you say yes here you get support for Linear Technology LTC4261
Negative Voltage Hot Swap Controller I2C interface.
If you say yes here you get support for the National Semiconductor
LM70, LM71, LM74 and Texas Instruments TMP121/TMP123 digital tempera-
ture sensor chips.
This driver can also be built as a module. If so, the module will
be called ltc4261.
This driver can also be built as a module. If so, the module
will be called lm70.
config SENSORS_LM95234
tristate "National Semiconductor LM95234"
config SENSORS_LM73
tristate "National Semiconductor LM73"
depends on I2C
help
If you say yes here you get support for the LM95234 temperature
sensor.
If you say yes here you get support for National Semiconductor LM73
sensor chips.
This driver can also be built as a module. If so, the module
will be called lm95234.
will be called lm73.
config SENSORS_LM95241
tristate "National Semiconductor LM95241 and compatibles"
config SENSORS_LM75
tristate "National Semiconductor LM75 and compatibles"
depends on I2C
depends on THERMAL || !THERMAL_OF
help
If you say yes here you get support for LM95231 and LM95241 sensor
chips.
If you say yes here you get support for one common type of
temperature sensor chip, with models including:
- Analog Devices ADT75
- Dallas Semiconductor DS75, DS1775 and DS7505
- Global Mixed-mode Technology (GMT) G751
- Maxim MAX6625 and MAX6626
- Microchip MCP980x
- National Semiconductor LM75, LM75A
- NXP's LM75A
- ST Microelectronics STDS75
- TelCom (now Microchip) TCN75
- Texas Instruments TMP100, TMP101, TMP105, TMP75, TMP175,
TMP275
This driver supports driver model based binding through board
specific I2C device tables.
It also supports the "legacy" style of driver binding. To use
that with some chips which don't replicate LM75 quirks exactly,
you may need the "force" module parameter.
This driver can also be built as a module. If so, the module
will be called lm95241.
will be called lm75.
config SENSORS_LM95245
tristate "National Semiconductor LM95245 sensor chip"
config SENSORS_LM77
tristate "National Semiconductor LM77"
depends on I2C
help
If you say yes here you get support for LM95245 sensor chip.
If you say yes here you get support for National Semiconductor LM77
sensor chips.
This driver can also be built as a module. If so, the module
will be called lm95245.
will be called lm77.
config SENSORS_MAX1111
tristate "Maxim MAX1111 Serial 8-bit ADC chip and compatibles"
depends on SPI_MASTER
config SENSORS_LM78
tristate "National Semiconductor LM78 and compatibles"
depends on I2C
select HWMON_VID
help
Say y here to support Maxim's MAX1110, MAX1111, MAX1112, and MAX1113
ADC chips.
If you say yes here you get support for National Semiconductor LM78,
LM78-J and LM79.
This driver can also be built as a module. If so, the module
will be called max1111.
will be called lm78.
config SENSORS_MAX16065
tristate "Maxim MAX16065 System Manager and compatibles"
config SENSORS_LM80
tristate "National Semiconductor LM80 and LM96080"
depends on I2C
help
If you say yes here you get support for hardware monitoring
capabilities of the following Maxim System Manager chips.
MAX16065
MAX16066
MAX16067
MAX16068
MAX16070
MAX16071
If you say yes here you get support for National Semiconductor
LM80 and LM96080 sensor chips.
This driver can also be built as a module. If so, the module
will be called max16065.
will be called lm80.
config SENSORS_MAX1619
tristate "Maxim MAX1619 sensor chip"
config SENSORS_LM83
tristate "National Semiconductor LM83 and compatibles"
depends on I2C
help
If you say yes here you get support for MAX1619 sensor chip.
If you say yes here you get support for National Semiconductor
LM82 and LM83 sensor chips.
This driver can also be built as a module. If so, the module
will be called max1619.
will be called lm83.
config SENSORS_MAX1668
tristate "Maxim MAX1668 and compatibles"
config SENSORS_LM85
tristate "National Semiconductor LM85 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for MAX1668, MAX1989 and
MAX1805 chips.
If you say yes here you get support for National Semiconductor LM85
sensor chips and clones: ADM1027, ADT7463, ADT7468, EMC6D100,
EMC6D101, EMC6D102, and EMC6D103.
This driver can also be built as a module. If so, the module
will be called max1668.
config SENSORS_MAX197
tristate "Maxim MAX197 and compatibles"
help
Support for the Maxim MAX197 A/D converter.
Support will include, but not be limited to, MAX197, and MAX199.
This driver can also be built as a module. If so, the module
will be called max197.
will be called lm85.
config SENSORS_MAX6639
tristate "Maxim MAX6639 sensor chip"
config SENSORS_LM87
tristate "National Semiconductor LM87 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for the MAX6639
sensor chips.
If you say yes here you get support for National Semiconductor LM87
and Analog Devices ADM1024 sensor chips.
This driver can also be built as a module. If so, the module
will be called max6639.
will be called lm87.
config SENSORS_MAX6642
tristate "Maxim MAX6642 sensor chip"
config SENSORS_LM90
tristate "National Semiconductor LM90 and compatibles"
depends on I2C
help
If you say yes here you get support for MAX6642 sensor chip.
MAX6642 is a SMBus-Compatible Remote/Local Temperature Sensor
with Overtemperature Alarm from Maxim.
If you say yes here you get support for National Semiconductor LM90,
LM86, LM89 and LM99, Analog Devices ADM1032, ADT7461, and ADT7461A,
Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6657, MAX6658, MAX6659,
MAX6680, MAX6681, MAX6692, MAX6695, MAX6696, ON Semiconductor NCT1008,
Winbond/Nuvoton W83L771W/G/AWG/ASG, Philips SA56004, and GMT G781
sensor chips.
This driver can also be built as a module. If so, the module
will be called max6642.
will be called lm90.
config SENSORS_MAX6650
tristate "Maxim MAX6650 sensor chip"
config SENSORS_LM92
tristate "National Semiconductor LM92 and compatibles"
depends on I2C
help
If you say yes here you get support for the MAX6650 / MAX6651
sensor chips.
If you say yes here you get support for National Semiconductor LM92
and Maxim MAX6635 sensor chips.
This driver can also be built as a module. If so, the module
will be called max6650.
will be called lm92.
config SENSORS_MAX6697
tristate "Maxim MAX6697 and compatibles"
config SENSORS_LM93
tristate "National Semiconductor LM93 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for MAX6581, MAX6602, MAX6622,
MAX6636, MAX6689, MAX6693, MAX6694, MAX6697, MAX6698, and MAX6699
temperature sensor chips.
If you say yes here you get support for National Semiconductor LM93,
LM94, and compatible sensor chips.
This driver can also be built as a module. If so, the module
will be called max6697.
will be called lm93.
config SENSORS_MCP3021
tristate "Microchip MCP3021 and compatibles"
config SENSORS_LM95234
tristate "National Semiconductor LM95234"
depends on I2C
help
If you say yes here you get support for MCP3021 and MCP3221.
The MCP3021 is a A/D converter (ADC) with 10-bit and the MCP3221
with 12-bit resolution.
If you say yes here you get support for the LM95234 temperature
sensor.
This driver can also be built as a module. If so, the module
will be called mcp3021.
will be called lm95234.
config SENSORS_NCT6775
tristate "Nuvoton NCT6775F and compatibles"
depends on !PPC
select HWMON_VID
config SENSORS_LM95241
tristate "National Semiconductor LM95241 and compatibles"
depends on I2C
help
If you say yes here you get support for the hardware monitoring
functionality of the Nuvoton NCT6775F, NCT6776F, NCT6779D
and compatible Super-I/O chips. This driver replaces the
w83627ehf driver for NCT6775F and NCT6776F.
If you say yes here you get support for LM95231 and LM95241 sensor
chips.
This driver can also be built as a module. If so, the module
will be called nct6775.
will be called lm95241.
config SENSORS_NTC_THERMISTOR
tristate "NTC thermistor support"
depends on (!OF && !IIO) || (OF && IIO)
config SENSORS_LM95245
tristate "National Semiconductor LM95245 sensor chip"
depends on I2C
help
This driver supports NTC thermistors sensor reading and its
interpretation. The driver can also monitor the temperature and
send notifications about the temperature.
Currently, this driver supports
NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473, and NCP15WL333.
If you say yes here you get support for LM95245 sensor chip.
This driver can also be built as a module. If so, the module
will be called ntc-thermistor.
will be called lm95245.
config SENSORS_PC87360
tristate "National Semiconductor PC87360 family"
......@@ -1011,6 +1051,33 @@ config SENSORS_PC87427
This driver can also be built as a module. If so, the module
will be called pc87427.
config SENSORS_NTC_THERMISTOR
tristate "NTC thermistor support"
depends on (!OF && !IIO) || (OF && IIO)
help
This driver supports NTC thermistors sensor reading and its
interpretation. The driver can also monitor the temperature and
send notifications about the temperature.
Currently, this driver supports
NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473, and NCP15WL333.
This driver can also be built as a module. If so, the module
will be called ntc-thermistor.
config SENSORS_NCT6775
tristate "Nuvoton NCT6775F and compatibles"
depends on !PPC
select HWMON_VID
help
If you say yes here you get support for the hardware monitoring
functionality of the Nuvoton NCT6775F, NCT6776F, NCT6779D
and compatible Super-I/O chips. This driver replaces the
w83627ehf driver for NCT6775F and NCT6776F.
This driver can also be built as a module. If so, the module
will be called nct6775.
config SENSORS_PCF8591
tristate "Philips PCF8591 ADC/DAC"
depends on I2C
......@@ -1074,21 +1141,6 @@ config SENSORS_SIS5595
This driver can also be built as a module. If so, the module
will be called sis5595.
config SENSORS_SMM665
tristate "Summit Microelectronics SMM665"
depends on I2C
default n
help
If you say yes here you get support for the hardware monitoring
features of the Summit Microelectronics SMM665/SMM665B Six-Channel
Active DC Output Controller / Monitor.
Other supported chips are SMM465, SMM665C, SMM764, and SMM766.
Support for those chips is untested.
This driver can also be built as a module. If so, the module will
be called smm665.
config SENSORS_DME1737
tristate "SMSC DME1737, SCH311x and compatibles"
depends on I2C && !PPC
......@@ -1210,6 +1262,31 @@ config SENSORS_SCH5636
This driver can also be built as a module. If so, the module
will be called sch5636.
config SENSORS_SMM665
tristate "Summit Microelectronics SMM665"
depends on I2C
default n
help
If you say yes here you get support for the hardware monitoring
features of the Summit Microelectronics SMM665/SMM665B Six-Channel
Active DC Output Controller / Monitor.
Other supported chips are SMM465, SMM665C, SMM764, and SMM766.
Support for those chips is untested.
This driver can also be built as a module. If so, the module will
be called smm665.
config SENSORS_ADC128D818
tristate "Texas Instruments ADC128D818"
depends on I2C
help
If you say yes here you get support for the Texas Instruments
ADC128D818 System Monitor with Temperature Sensor chip.
This driver can also be built as a module. If so, the module
will be called adc128d818.
config SENSORS_ADS1015
tristate "Texas Instruments ADS1015"
depends on I2C
......@@ -1525,37 +1602,6 @@ config SENSORS_ULTRA45
This driver provides support for the Ultra45 workstation environmental
sensors.
config SENSORS_APPLESMC
tristate "Apple SMC (Motion sensor, light sensor, keyboard backlight)"
depends on INPUT && X86
select NEW_LEDS
select LEDS_CLASS
select INPUT_POLLDEV
default n
help
This driver provides support for the Apple System Management
Controller, which provides an accelerometer (Apple Sudden Motion
Sensor), light sensors, temperature sensors, keyboard backlight
control and fan control.
Only Intel-based Apple's computers are supported (MacBook Pro,
MacBook, MacMini).
Data from the different sensors, keyboard backlight control and fan
control are accessible via sysfs.
This driver also provides an absolute input class device, allowing
the laptop to act as a pinball machine-esque joystick.
Say Y here if you have an applicable laptop and want to experience
the awesome power of applesmc.
config SENSORS_MC13783_ADC
tristate "Freescale MC13783/MC13892 ADC"
depends on MFD_MC13XXX
help
Support for the A/D converter on MC13783 and MC13892 PMIC.
if ACPI
comment "ACPI drivers"
......
......@@ -25,6 +25,7 @@ obj-$(CONFIG_SENSORS_ABITUGURU3)+= abituguru3.o
obj-$(CONFIG_SENSORS_AD7314) += ad7314.o
obj-$(CONFIG_SENSORS_AD7414) += ad7414.o
obj-$(CONFIG_SENSORS_AD7418) += ad7418.o
obj-$(CONFIG_SENSORS_ADC128D818) += adc128d818.o
obj-$(CONFIG_SENSORS_ADCXX) += adcxx.o
obj-$(CONFIG_SENSORS_ADM1021) += adm1021.o
obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o
......@@ -95,9 +96,12 @@ obj-$(CONFIG_SENSORS_LM93) += lm93.o
obj-$(CONFIG_SENSORS_LM95234) += lm95234.o
obj-$(CONFIG_SENSORS_LM95241) += lm95241.o
obj-$(CONFIG_SENSORS_LM95245) += lm95245.o
obj-$(CONFIG_SENSORS_LTC2945) += ltc2945.o
obj-$(CONFIG_SENSORS_LTC4151) += ltc4151.o
obj-$(CONFIG_SENSORS_LTC4215) += ltc4215.o
obj-$(CONFIG_SENSORS_LTC4222) += ltc4222.o
obj-$(CONFIG_SENSORS_LTC4245) += ltc4245.o
obj-$(CONFIG_SENSORS_LTC4260) += ltc4260.o
obj-$(CONFIG_SENSORS_LTC4261) += ltc4261.o
obj-$(CONFIG_SENSORS_MAX1111) += max1111.o
obj-$(CONFIG_SENSORS_MAX16065) += max16065.o
......
/*
* Driver for TI ADC128D818 System Monitor with Temperature Sensor
*
* Copyright (c) 2014 Guenter Roeck
*
* Derived from lm80.c
* Copyright (C) 1998, 1999 Frodo Looijaard <frodol@dds.nl>
* and Philip Edelbrock <phil@netroedge.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/regulator/consumer.h>
#include <linux/mutex.h>
/* Addresses to scan
* The chip also supports addresses 0x35..0x37. Don't scan those addresses
* since they are also used by some EEPROMs, which may result in false
* positives.
*/
static const unsigned short normal_i2c[] = {
0x1d, 0x1e, 0x1f, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END };
/* registers */
#define ADC128_REG_IN_MAX(nr) (0x2a + (nr) * 2)
#define ADC128_REG_IN_MIN(nr) (0x2b + (nr) * 2)
#define ADC128_REG_IN(nr) (0x20 + (nr))
#define ADC128_REG_TEMP 0x27
#define ADC128_REG_TEMP_MAX 0x38
#define ADC128_REG_TEMP_HYST 0x39
#define ADC128_REG_CONFIG 0x00
#define ADC128_REG_ALARM 0x01
#define ADC128_REG_MASK 0x03
#define ADC128_REG_CONV_RATE 0x07
#define ADC128_REG_ONESHOT 0x09
#define ADC128_REG_SHUTDOWN 0x0a
#define ADC128_REG_CONFIG_ADV 0x0b
#define ADC128_REG_BUSY_STATUS 0x0c
#define ADC128_REG_MAN_ID 0x3e
#define ADC128_REG_DEV_ID 0x3f
struct adc128_data {
struct i2c_client *client;
struct regulator *regulator;
int vref; /* Reference voltage in mV */
struct mutex update_lock;
bool valid; /* true if following fields are valid */
unsigned long last_updated; /* In jiffies */
u16 in[3][7]; /* Register value, normalized to 12 bit
* 0: input voltage
* 1: min limit
* 2: max limit
*/
s16 temp[3]; /* Register value, normalized to 9 bit
* 0: sensor 1: limit 2: hyst
*/
u8 alarms; /* alarm register value */
};
static struct adc128_data *adc128_update_device(struct device *dev)
{
struct adc128_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
struct adc128_data *ret = data;
int i, rv;
mutex_lock(&data->update_lock);
if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
for (i = 0; i < 7; i++) {
rv = i2c_smbus_read_word_swapped(client,
ADC128_REG_IN(i));
if (rv < 0)
goto abort;
data->in[0][i] = rv >> 4;
rv = i2c_smbus_read_byte_data(client,
ADC128_REG_IN_MIN(i));
if (rv < 0)
goto abort;
data->in[1][i] = rv << 4;
rv = i2c_smbus_read_byte_data(client,
ADC128_REG_IN_MAX(i));
if (rv < 0)
goto abort;
data->in[2][i] = rv << 4;
}
rv = i2c_smbus_read_word_swapped(client, ADC128_REG_TEMP);
if (rv < 0)
goto abort;
data->temp[0] = rv >> 7;
rv = i2c_smbus_read_byte_data(client, ADC128_REG_TEMP_MAX);
if (rv < 0)
goto abort;
data->temp[1] = rv << 1;
rv = i2c_smbus_read_byte_data(client, ADC128_REG_TEMP_HYST);
if (rv < 0)
goto abort;
data->temp[2] = rv << 1;
rv = i2c_smbus_read_byte_data(client, ADC128_REG_ALARM);
if (rv < 0)
goto abort;
data->alarms |= rv;
data->last_updated = jiffies;
data->valid = true;
}
goto done;
abort:
ret = ERR_PTR(rv);
data->valid = false;
done:
mutex_unlock(&data->update_lock);
return ret;
}
static ssize_t adc128_show_in(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct adc128_data *data = adc128_update_device(dev);
int index = to_sensor_dev_attr_2(attr)->index;
int nr = to_sensor_dev_attr_2(attr)->nr;
int val;
if (IS_ERR(data))
return PTR_ERR(data);
val = DIV_ROUND_CLOSEST(data->in[index][nr] * data->vref, 4095);
return sprintf(buf, "%d\n", val);
}
static ssize_t adc128_set_in(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct adc128_data *data = dev_get_drvdata(dev);
int index = to_sensor_dev_attr_2(attr)->index;
int nr = to_sensor_dev_attr_2(attr)->nr;
u8 reg, regval;
long val;
int err;
err = kstrtol(buf, 10, &val);
if (err < 0)
return err;
mutex_lock(&data->update_lock);
/* 10 mV LSB on limit registers */
regval = clamp_val(DIV_ROUND_CLOSEST(val, 10), 0, 255);
data->in[index][nr] = regval << 4;
reg = index == 1 ? ADC128_REG_IN_MIN(nr) : ADC128_REG_IN_MAX(nr);
i2c_smbus_write_byte_data(data->client, reg, regval);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t adc128_show_temp(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct adc128_data *data = adc128_update_device(dev);
int index = to_sensor_dev_attr(attr)->index;
int temp;
if (IS_ERR(data))
return PTR_ERR(data);
temp = (data->temp[index] << 7) >> 7; /* sign extend */
return sprintf(buf, "%d\n", temp * 500);/* 0.5 degrees C resolution */
}
static ssize_t adc128_set_temp(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct adc128_data *data = dev_get_drvdata(dev);
int index = to_sensor_dev_attr(attr)->index;
long val;
int err;
s8 regval;
err = kstrtol(buf, 10, &val);
if (err < 0)
return err;
mutex_lock(&data->update_lock);
regval = clamp_val(DIV_ROUND_CLOSEST(val, 1000), -128, 127);
data->temp[index] = regval << 1;
i2c_smbus_write_byte_data(data->client,
index == 1 ? ADC128_REG_TEMP_MAX
: ADC128_REG_TEMP_HYST,
regval);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t adc128_show_alarm(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct adc128_data *data = adc128_update_device(dev);
int mask = 1 << to_sensor_dev_attr(attr)->index;
u8 alarms;
if (IS_ERR(data))
return PTR_ERR(data);
/*
* Clear an alarm after reporting it to user space. If it is still
* active, the next update sequence will set the alarm bit again.
*/
alarms = data->alarms;
data->alarms &= ~mask;
return sprintf(buf, "%u\n", !!(alarms & mask));
}
static SENSOR_DEVICE_ATTR_2(in0_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 0, 0);
static SENSOR_DEVICE_ATTR_2(in0_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 0, 1);
static SENSOR_DEVICE_ATTR_2(in0_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 0, 2);
static SENSOR_DEVICE_ATTR_2(in1_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 1, 0);
static SENSOR_DEVICE_ATTR_2(in1_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 1, 1);
static SENSOR_DEVICE_ATTR_2(in1_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 1, 2);
static SENSOR_DEVICE_ATTR_2(in2_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 2, 0);
static SENSOR_DEVICE_ATTR_2(in2_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 2, 1);
static SENSOR_DEVICE_ATTR_2(in2_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 2, 2);
static SENSOR_DEVICE_ATTR_2(in3_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 3, 0);
static SENSOR_DEVICE_ATTR_2(in3_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 3, 1);
static SENSOR_DEVICE_ATTR_2(in3_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 3, 2);
static SENSOR_DEVICE_ATTR_2(in4_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 4, 0);
static SENSOR_DEVICE_ATTR_2(in4_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 4, 1);
static SENSOR_DEVICE_ATTR_2(in4_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 4, 2);
static SENSOR_DEVICE_ATTR_2(in5_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 5, 0);
static SENSOR_DEVICE_ATTR_2(in5_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 5, 1);
static SENSOR_DEVICE_ATTR_2(in5_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 5, 2);
static SENSOR_DEVICE_ATTR_2(in6_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 6, 0);
static SENSOR_DEVICE_ATTR_2(in6_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 6, 1);
static SENSOR_DEVICE_ATTR_2(in6_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 6, 2);
static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, adc128_show_temp, NULL, 0);
static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO,
adc128_show_temp, adc128_set_temp, 1);
static SENSOR_DEVICE_ATTR(temp1_max_hyst, S_IWUSR | S_IRUGO,
adc128_show_temp, adc128_set_temp, 2);
static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, adc128_show_alarm, NULL, 0);
static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, adc128_show_alarm, NULL, 1);
static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, adc128_show_alarm, NULL, 2);
static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, adc128_show_alarm, NULL, 3);
static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, adc128_show_alarm, NULL, 4);
static SENSOR_DEVICE_ATTR(in5_alarm, S_IRUGO, adc128_show_alarm, NULL, 5);
static SENSOR_DEVICE_ATTR(in6_alarm, S_IRUGO, adc128_show_alarm, NULL, 6);
static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, adc128_show_alarm, NULL, 7);
static struct attribute *adc128_attrs[] = {
&sensor_dev_attr_in0_min.dev_attr.attr,
&sensor_dev_attr_in1_min.dev_attr.attr,
&sensor_dev_attr_in2_min.dev_attr.attr,
&sensor_dev_attr_in3_min.dev_attr.attr,
&sensor_dev_attr_in4_min.dev_attr.attr,
&sensor_dev_attr_in5_min.dev_attr.attr,
&sensor_dev_attr_in6_min.dev_attr.attr,
&sensor_dev_attr_in0_max.dev_attr.attr,
&sensor_dev_attr_in1_max.dev_attr.attr,
&sensor_dev_attr_in2_max.dev_attr.attr,
&sensor_dev_attr_in3_max.dev_attr.attr,
&sensor_dev_attr_in4_max.dev_attr.attr,
&sensor_dev_attr_in5_max.dev_attr.attr,
&sensor_dev_attr_in6_max.dev_attr.attr,
&sensor_dev_attr_in0_input.dev_attr.attr,
&sensor_dev_attr_in1_input.dev_attr.attr,
&sensor_dev_attr_in2_input.dev_attr.attr,
&sensor_dev_attr_in3_input.dev_attr.attr,
&sensor_dev_attr_in4_input.dev_attr.attr,
&sensor_dev_attr_in5_input.dev_attr.attr,
&sensor_dev_attr_in6_input.dev_attr.attr,
&sensor_dev_attr_temp1_input.dev_attr.attr,
&sensor_dev_attr_temp1_max.dev_attr.attr,
&sensor_dev_attr_temp1_max_hyst.dev_attr.attr,
&sensor_dev_attr_in0_alarm.dev_attr.attr,
&sensor_dev_attr_in1_alarm.dev_attr.attr,
&sensor_dev_attr_in2_alarm.dev_attr.attr,
&sensor_dev_attr_in3_alarm.dev_attr.attr,
&sensor_dev_attr_in4_alarm.dev_attr.attr,
&sensor_dev_attr_in5_alarm.dev_attr.attr,
&sensor_dev_attr_in6_alarm.dev_attr.attr,
&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
NULL
};
ATTRIBUTE_GROUPS(adc128);
static int adc128_detect(struct i2c_client *client, struct i2c_board_info *info)
{
int man_id, dev_id;
if (!i2c_check_functionality(client->adapter,
I2C_FUNC_SMBUS_BYTE_DATA |
I2C_FUNC_SMBUS_WORD_DATA))
return -ENODEV;
man_id = i2c_smbus_read_byte_data(client, ADC128_REG_MAN_ID);
dev_id = i2c_smbus_read_byte_data(client, ADC128_REG_DEV_ID);
if (man_id != 0x01 || dev_id != 0x09)
return -ENODEV;
/* Check unused bits for confirmation */
if (i2c_smbus_read_byte_data(client, ADC128_REG_CONFIG) & 0xf4)
return -ENODEV;
if (i2c_smbus_read_byte_data(client, ADC128_REG_CONV_RATE) & 0xfe)
return -ENODEV;
if (i2c_smbus_read_byte_data(client, ADC128_REG_ONESHOT) & 0xfe)
return -ENODEV;
if (i2c_smbus_read_byte_data(client, ADC128_REG_SHUTDOWN) & 0xfe)
return -ENODEV;
if (i2c_smbus_read_byte_data(client, ADC128_REG_CONFIG_ADV) & 0xf8)
return -ENODEV;
if (i2c_smbus_read_byte_data(client, ADC128_REG_BUSY_STATUS) & 0xfc)
return -ENODEV;
strlcpy(info->type, "adc128d818", I2C_NAME_SIZE);
return 0;
}
static int adc128_init_client(struct adc128_data *data)
{
struct i2c_client *client = data->client;
int err;
/*
* Reset chip to defaults.
* This makes most other initializations unnecessary.
*/
err = i2c_smbus_write_byte_data(client, ADC128_REG_CONFIG, 0x80);
if (err)
return err;
/* Start monitoring */
err = i2c_smbus_write_byte_data(client, ADC128_REG_CONFIG, 0x01);
if (err)
return err;
/* If external vref is selected, configure the chip to use it */
if (data->regulator) {
err = i2c_smbus_write_byte_data(client,
ADC128_REG_CONFIG_ADV, 0x01);
if (err)
return err;
}
return 0;
}
static int adc128_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct device *dev = &client->dev;
struct regulator *regulator;
struct device *hwmon_dev;
struct adc128_data *data;
int err, vref;
data = devm_kzalloc(dev, sizeof(struct adc128_data), GFP_KERNEL);
if (!data)
return -ENOMEM;
/* vref is optional. If specified, is used as chip reference voltage */
regulator = devm_regulator_get_optional(dev, "vref");
if (!IS_ERR(regulator)) {
data->regulator = regulator;
err = regulator_enable(regulator);
if (err < 0)
return err;
vref = regulator_get_voltage(regulator);
if (vref < 0) {
err = vref;
goto error;
}
data->vref = DIV_ROUND_CLOSEST(vref, 1000);
} else {
data->vref = 2560; /* 2.56V, in mV */
}
data->client = client;
i2c_set_clientdata(client, data);
mutex_init(&data->update_lock);
/* Initialize the chip */
err = adc128_init_client(data);
if (err < 0)
goto error;
hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
data, adc128_groups);
if (IS_ERR(hwmon_dev)) {
err = PTR_ERR(hwmon_dev);
goto error;
}
return 0;
error:
if (data->regulator)
regulator_disable(data->regulator);
return err;
}
static int adc128_remove(struct i2c_client *client)
{
struct adc128_data *data = i2c_get_clientdata(client);
if (data->regulator)
regulator_disable(data->regulator);
return 0;
}
static const struct i2c_device_id adc128_id[] = {
{ "adc128d818", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, adc128_id);
static struct i2c_driver adc128_driver = {
.class = I2C_CLASS_HWMON,
.driver = {
.name = "adc128d818",
},
.probe = adc128_probe,
.remove = adc128_remove,
.id_table = adc128_id,
.detect = adc128_detect,
.address_list = normal_i2c,
};
module_i2c_driver(adc128_driver);
MODULE_AUTHOR("Guenter Roeck");
MODULE_DESCRIPTION("Driver for ADC128D818");
MODULE_LICENSE("GPL");
......@@ -94,6 +94,8 @@ struct temp_data {
bool valid;
struct sensor_device_attribute sd_attrs[TOTAL_ATTRS];
char attr_name[TOTAL_ATTRS][CORETEMP_NAME_LENGTH];
struct attribute *attrs[TOTAL_ATTRS + 1];
struct attribute_group attr_group;
struct mutex update_lock;
};
......@@ -114,12 +116,6 @@ struct pdev_entry {
static LIST_HEAD(pdev_list);
static DEFINE_MUTEX(pdev_list_mutex);
static ssize_t show_name(struct device *dev,
struct device_attribute *devattr, char *buf)
{
return sprintf(buf, "%s\n", DRVNAME);
}
static ssize_t show_label(struct device *dev,
struct device_attribute *devattr, char *buf)
{
......@@ -393,20 +389,10 @@ static int get_tjmax(struct cpuinfo_x86 *c, u32 id, struct device *dev)
return adjust_tjmax(c, id, dev);
}
static int create_name_attr(struct platform_data *pdata,
struct device *dev)
{
sysfs_attr_init(&pdata->name_attr.attr);
pdata->name_attr.attr.name = "name";
pdata->name_attr.attr.mode = S_IRUGO;
pdata->name_attr.show = show_name;
return device_create_file(dev, &pdata->name_attr);
}
static int create_core_attrs(struct temp_data *tdata, struct device *dev,
int attr_no)
{
int err, i;
int i;
static ssize_t (*const rd_ptr[TOTAL_ATTRS]) (struct device *dev,
struct device_attribute *devattr, char *buf) = {
show_label, show_crit_alarm, show_temp, show_tjmax,
......@@ -424,16 +410,10 @@ static int create_core_attrs(struct temp_data *tdata, struct device *dev,
tdata->sd_attrs[i].dev_attr.attr.mode = S_IRUGO;
tdata->sd_attrs[i].dev_attr.show = rd_ptr[i];
tdata->sd_attrs[i].index = attr_no;
err = device_create_file(dev, &tdata->sd_attrs[i].dev_attr);
if (err)
goto exit_free;
tdata->attrs[i] = &tdata->sd_attrs[i].dev_attr.attr;
}
return 0;
exit_free:
while (--i >= 0)
device_remove_file(dev, &tdata->sd_attrs[i].dev_attr);
return err;
tdata->attr_group.attrs = tdata->attrs;
return sysfs_create_group(&dev->kobj, &tdata->attr_group);
}
......@@ -548,7 +528,7 @@ static int create_core_data(struct platform_device *pdev, unsigned int cpu,
pdata->core_data[attr_no] = tdata;
/* Create sysfs interfaces */
err = create_core_attrs(tdata, &pdev->dev, attr_no);
err = create_core_attrs(tdata, pdata->hwmon_dev, attr_no);
if (err)
goto exit_free;
......@@ -573,14 +553,12 @@ static void coretemp_add_core(unsigned int cpu, int pkg_flag)
}
static void coretemp_remove_core(struct platform_data *pdata,
struct device *dev, int indx)
int indx)
{
int i;
struct temp_data *tdata = pdata->core_data[indx];
/* Remove the sysfs attributes */
for (i = 0; i < tdata->attr_size; i++)
device_remove_file(dev, &tdata->sd_attrs[i].dev_attr);
sysfs_remove_group(&pdata->hwmon_dev->kobj, &tdata->attr_group);
kfree(pdata->core_data[indx]);
pdata->core_data[indx] = NULL;
......@@ -588,34 +566,20 @@ static void coretemp_remove_core(struct platform_data *pdata,
static int coretemp_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct platform_data *pdata;
int err;
/* Initialize the per-package data structures */
pdata = kzalloc(sizeof(struct platform_data), GFP_KERNEL);
pdata = devm_kzalloc(dev, sizeof(struct platform_data), GFP_KERNEL);
if (!pdata)
return -ENOMEM;
err = create_name_attr(pdata, &pdev->dev);
if (err)
goto exit_free;
pdata->phys_proc_id = pdev->id;
platform_set_drvdata(pdev, pdata);
pdata->hwmon_dev = hwmon_device_register(&pdev->dev);
if (IS_ERR(pdata->hwmon_dev)) {
err = PTR_ERR(pdata->hwmon_dev);
dev_err(&pdev->dev, "Class registration failed (%d)\n", err);
goto exit_name;
}
return 0;
exit_name:
device_remove_file(&pdev->dev, &pdata->name_attr);
exit_free:
kfree(pdata);
return err;
pdata->hwmon_dev = devm_hwmon_device_register_with_groups(dev, DRVNAME,
pdata, NULL);
return PTR_ERR_OR_ZERO(pdata->hwmon_dev);
}
static int coretemp_remove(struct platform_device *pdev)
......@@ -625,11 +589,8 @@ static int coretemp_remove(struct platform_device *pdev)
for (i = MAX_CORE_DATA - 1; i >= 0; --i)
if (pdata->core_data[i])
coretemp_remove_core(pdata, &pdev->dev, i);
coretemp_remove_core(pdata, i);
device_remove_file(&pdev->dev, &pdata->name_attr);
hwmon_device_unregister(pdata->hwmon_dev);
kfree(pdata);
return 0;
}
......@@ -777,7 +738,7 @@ static void put_core_offline(unsigned int cpu)
return;
if (pdata->core_data[indx] && pdata->core_data[indx]->cpu == cpu)
coretemp_remove_core(pdata, &pdev->dev, indx);
coretemp_remove_core(pdata, indx);
/*
* If a HT sibling of a core is taken offline, but another HT sibling
......
......@@ -349,7 +349,7 @@ static ssize_t set_fan_div(struct device *dev, struct device_attribute *da,
dev_dbg(&client->dev, "reg 0x%02x, err %d\n",
REG_FAN_CONF1, status);
mutex_unlock(&data->update_lock);
return -EIO;
return status;
}
status &= 0x9F;
status |= (new_range_bits << 5);
......
......@@ -22,6 +22,7 @@
#include <linux/gfp.h>
#include <linux/spinlock.h>
#include <linux/pci.h>
#include <linux/string.h>
#define HWMON_ID_PREFIX "hwmon"
#define HWMON_ID_FORMAT HWMON_ID_PREFIX "%d"
......@@ -99,6 +100,10 @@ hwmon_device_register_with_groups(struct device *dev, const char *name,
struct hwmon_device *hwdev;
int err, id;
/* Do not accept invalid characters in hwmon name attribute */
if (name && (!strlen(name) || strpbrk(name, "-* \t\n")))
return ERR_PTR(-EINVAL);
id = ida_simple_get(&hwmon_ida, 0, 0, GFP_KERNEL);
if (id < 0)
return ERR_PTR(id);
......
......@@ -31,6 +31,7 @@ struct iio_hwmon_state {
int num_channels;
struct device *hwmon_dev;
struct attribute_group attr_group;
const struct attribute_group *groups[2];
struct attribute **attrs;
};
......@@ -56,19 +57,6 @@ static ssize_t iio_hwmon_read_val(struct device *dev,
return sprintf(buf, "%d\n", result);
}
static ssize_t show_name(struct device *dev, struct device_attribute *attr,
char *buf)
{
const char *name = "iio_hwmon";
if (dev->of_node && dev->of_node->name)
name = dev->of_node->name;
return sprintf(buf, "%s\n", name);
}
static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
static int iio_hwmon_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
......@@ -78,6 +66,10 @@ static int iio_hwmon_probe(struct platform_device *pdev)
int in_i = 1, temp_i = 1, curr_i = 1;
enum iio_chan_type type;
struct iio_channel *channels;
const char *name = "iio_hwmon";
if (dev->of_node && dev->of_node->name)
name = dev->of_node->name;
channels = iio_channel_get_all(dev);
if (IS_ERR(channels))
......@@ -96,7 +88,7 @@ static int iio_hwmon_probe(struct platform_device *pdev)
st->num_channels++;
st->attrs = devm_kzalloc(dev,
sizeof(*st->attrs) * (st->num_channels + 2),
sizeof(*st->attrs) * (st->num_channels + 1),
GFP_KERNEL);
if (st->attrs == NULL) {
ret = -ENOMEM;
......@@ -144,22 +136,18 @@ static int iio_hwmon_probe(struct platform_device *pdev)
a->index = i;
st->attrs[i] = &a->dev_attr.attr;
}
st->attrs[st->num_channels] = &dev_attr_name.attr;
st->attr_group.attrs = st->attrs;
platform_set_drvdata(pdev, st);
ret = sysfs_create_group(&dev->kobj, &st->attr_group);
if (ret < 0)
goto error_release_channels;
st->hwmon_dev = hwmon_device_register(dev);
st->attr_group.attrs = st->attrs;
st->groups[0] = &st->attr_group;
st->hwmon_dev = hwmon_device_register_with_groups(dev, name, st,
st->groups);
if (IS_ERR(st->hwmon_dev)) {
ret = PTR_ERR(st->hwmon_dev);
goto error_remove_group;
goto error_release_channels;
}
platform_set_drvdata(pdev, st);
return 0;
error_remove_group:
sysfs_remove_group(&dev->kobj, &st->attr_group);
error_release_channels:
iio_channel_release_all(channels);
return ret;
......@@ -170,7 +158,6 @@ static int iio_hwmon_remove(struct platform_device *pdev)
struct iio_hwmon_state *st = platform_get_drvdata(pdev);
hwmon_device_unregister(st->hwmon_dev);
sysfs_remove_group(&pdev->dev.kobj, &st->attr_group);
iio_channel_release_all(st->channels);
return 0;
......
......@@ -28,7 +28,6 @@
#include <linux/hwmon.h>
struct jz4740_hwmon {
struct resource *mem;
void __iomem *base;
int irq;
......@@ -106,6 +105,7 @@ static int jz4740_hwmon_probe(struct platform_device *pdev)
{
int ret;
struct jz4740_hwmon *hwmon;
struct resource *mem;
hwmon = devm_kzalloc(&pdev->dev, sizeof(*hwmon), GFP_KERNEL);
if (!hwmon)
......@@ -120,25 +120,10 @@ static int jz4740_hwmon_probe(struct platform_device *pdev)
return hwmon->irq;
}
hwmon->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!hwmon->mem) {
dev_err(&pdev->dev, "Failed to get platform mmio resource\n");
return -ENOENT;
}
hwmon->mem = devm_request_mem_region(&pdev->dev, hwmon->mem->start,
resource_size(hwmon->mem), pdev->name);
if (!hwmon->mem) {
dev_err(&pdev->dev, "Failed to request mmio memory region\n");
return -EBUSY;
}
hwmon->base = devm_ioremap_nocache(&pdev->dev, hwmon->mem->start,
resource_size(hwmon->mem));
if (!hwmon->base) {
dev_err(&pdev->dev, "Failed to ioremap mmio memory\n");
return -EBUSY;
}
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
hwmon->base = devm_ioremap_resource(&pdev->dev, mem);
if (IS_ERR(hwmon->base))
return PTR_ERR(hwmon->base);
init_completion(&hwmon->read_completion);
mutex_init(&hwmon->lock);
......
......@@ -89,7 +89,7 @@ static const u8 lm95241_reg_address[] = {
/* Client data (each client gets its own) */
struct lm95241_data {
struct device *hwmon_dev;
struct i2c_client *client;
struct mutex update_lock;
unsigned long last_updated, interval; /* in jiffies */
char valid; /* zero until following fields are valid */
......@@ -113,8 +113,8 @@ static int temp_from_reg_unsigned(u8 val_h, u8 val_l)
static struct lm95241_data *lm95241_update_device(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95241_data *data = i2c_get_clientdata(client);
struct lm95241_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
mutex_lock(&data->update_lock);
......@@ -122,7 +122,7 @@ static struct lm95241_data *lm95241_update_device(struct device *dev)
!data->valid) {
int i;
dev_dbg(&client->dev, "Updating lm95241 data.\n");
dev_dbg(dev, "Updating lm95241 data.\n");
for (i = 0; i < ARRAY_SIZE(lm95241_reg_address); i++)
data->temp[i]
= i2c_smbus_read_byte_data(client,
......@@ -153,8 +153,7 @@ static ssize_t show_input(struct device *dev, struct device_attribute *attr,
static ssize_t show_type(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95241_data *data = i2c_get_clientdata(client);
struct lm95241_data *data = dev_get_drvdata(dev);
return snprintf(buf, PAGE_SIZE - 1,
data->model & to_sensor_dev_attr(attr)->index ? "1\n" : "2\n");
......@@ -163,8 +162,8 @@ static ssize_t show_type(struct device *dev, struct device_attribute *attr,
static ssize_t set_type(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95241_data *data = i2c_get_clientdata(client);
struct lm95241_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
unsigned long val;
int shift;
u8 mask = to_sensor_dev_attr(attr)->index;
......@@ -201,8 +200,7 @@ static ssize_t set_type(struct device *dev, struct device_attribute *attr,
static ssize_t show_min(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95241_data *data = i2c_get_clientdata(client);
struct lm95241_data *data = dev_get_drvdata(dev);
return snprintf(buf, PAGE_SIZE - 1,
data->config & to_sensor_dev_attr(attr)->index ?
......@@ -212,8 +210,7 @@ static ssize_t show_min(struct device *dev, struct device_attribute *attr,
static ssize_t set_min(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95241_data *data = i2c_get_clientdata(client);
struct lm95241_data *data = dev_get_drvdata(dev);
long val;
if (kstrtol(buf, 10, &val) < 0)
......@@ -229,7 +226,8 @@ static ssize_t set_min(struct device *dev, struct device_attribute *attr,
data->config &= ~to_sensor_dev_attr(attr)->index;
data->valid = 0;
i2c_smbus_write_byte_data(client, LM95241_REG_RW_CONFIG, data->config);
i2c_smbus_write_byte_data(data->client, LM95241_REG_RW_CONFIG,
data->config);
mutex_unlock(&data->update_lock);
......@@ -239,8 +237,7 @@ static ssize_t set_min(struct device *dev, struct device_attribute *attr,
static ssize_t show_max(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95241_data *data = i2c_get_clientdata(client);
struct lm95241_data *data = dev_get_drvdata(dev);
return snprintf(buf, PAGE_SIZE - 1,
data->config & to_sensor_dev_attr(attr)->index ?
......@@ -250,8 +247,7 @@ static ssize_t show_max(struct device *dev, struct device_attribute *attr,
static ssize_t set_max(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95241_data *data = i2c_get_clientdata(client);
struct lm95241_data *data = dev_get_drvdata(dev);
long val;
if (kstrtol(buf, 10, &val) < 0)
......@@ -267,7 +263,8 @@ static ssize_t set_max(struct device *dev, struct device_attribute *attr,
data->config &= ~to_sensor_dev_attr(attr)->index;
data->valid = 0;
i2c_smbus_write_byte_data(client, LM95241_REG_RW_CONFIG, data->config);
i2c_smbus_write_byte_data(data->client, LM95241_REG_RW_CONFIG,
data->config);
mutex_unlock(&data->update_lock);
......@@ -286,8 +283,7 @@ static ssize_t show_interval(struct device *dev, struct device_attribute *attr,
static ssize_t set_interval(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95241_data *data = i2c_get_clientdata(client);
struct lm95241_data *data = dev_get_drvdata(dev);
unsigned long val;
if (kstrtoul(buf, 10, &val) < 0)
......@@ -316,7 +312,7 @@ static SENSOR_DEVICE_ATTR(temp3_max, S_IWUSR | S_IRUGO, show_max, set_max,
static DEVICE_ATTR(update_interval, S_IWUSR | S_IRUGO, show_interval,
set_interval);
static struct attribute *lm95241_attributes[] = {
static struct attribute *lm95241_attrs[] = {
&sensor_dev_attr_temp1_input.dev_attr.attr,
&sensor_dev_attr_temp2_input.dev_attr.attr,
&sensor_dev_attr_temp3_input.dev_attr.attr,
......@@ -329,10 +325,7 @@ static struct attribute *lm95241_attributes[] = {
&dev_attr_update_interval.attr,
NULL
};
static const struct attribute_group lm95241_group = {
.attrs = lm95241_attributes,
};
ATTRIBUTE_GROUPS(lm95241);
/* Return 0 if detection is successful, -ENODEV otherwise */
static int lm95241_detect(struct i2c_client *new_client,
......@@ -366,14 +359,11 @@ static int lm95241_detect(struct i2c_client *new_client,
return 0;
}
static void lm95241_init_client(struct i2c_client *client)
static void lm95241_init_client(struct i2c_client *client,
struct lm95241_data *data)
{
struct lm95241_data *data = i2c_get_clientdata(client);
data->interval = HZ; /* 1 sec default */
data->valid = 0;
data->config = CFG_CR0076;
data->model = 0;
data->trutherm = (TT_OFF << TT1_SHIFT) | (TT_OFF << TT2_SHIFT);
i2c_smbus_write_byte_data(client, LM95241_REG_RW_CONFIG, data->config);
......@@ -385,49 +375,27 @@ static void lm95241_init_client(struct i2c_client *client)
data->model);
}
static int lm95241_probe(struct i2c_client *new_client,
static int lm95241_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct device *dev = &client->dev;
struct lm95241_data *data;
int err;
struct device *hwmon_dev;
data = devm_kzalloc(&new_client->dev, sizeof(struct lm95241_data),
GFP_KERNEL);
data = devm_kzalloc(dev, sizeof(struct lm95241_data), GFP_KERNEL);
if (!data)
return -ENOMEM;
i2c_set_clientdata(new_client, data);
data->client = client;
mutex_init(&data->update_lock);
/* Initialize the LM95241 chip */
lm95241_init_client(new_client);
lm95241_init_client(client, data);
/* Register sysfs hooks */
err = sysfs_create_group(&new_client->dev.kobj, &lm95241_group);
if (err)
return err;
data->hwmon_dev = hwmon_device_register(&new_client->dev);
if (IS_ERR(data->hwmon_dev)) {
err = PTR_ERR(data->hwmon_dev);
goto exit_remove_files;
}
return 0;
exit_remove_files:
sysfs_remove_group(&new_client->dev.kobj, &lm95241_group);
return err;
}
static int lm95241_remove(struct i2c_client *client)
{
struct lm95241_data *data = i2c_get_clientdata(client);
hwmon_device_unregister(data->hwmon_dev);
sysfs_remove_group(&client->dev.kobj, &lm95241_group);
return 0;
hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
data,
lm95241_groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
}
/* Driver data (common to all clients) */
......@@ -444,7 +412,6 @@ static struct i2c_driver lm95241_driver = {
.name = DEVNAME,
},
.probe = lm95241_probe,
.remove = lm95241_remove,
.id_table = lm95241_id,
.detect = lm95241_detect,
.address_list = normal_i2c,
......
......@@ -115,7 +115,7 @@ static const u8 lm95245_reg_address[] = {
/* Client data (each client gets its own) */
struct lm95245_data {
struct device *hwmon_dev;
struct i2c_client *client;
struct mutex update_lock;
unsigned long last_updated; /* in jiffies */
unsigned long interval; /* in msecs */
......@@ -140,8 +140,8 @@ static int temp_from_reg_signed(u8 val_h, u8 val_l)
static struct lm95245_data *lm95245_update_device(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95245_data *data = i2c_get_clientdata(client);
struct lm95245_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
mutex_lock(&data->update_lock);
......@@ -149,7 +149,6 @@ static struct lm95245_data *lm95245_update_device(struct device *dev)
+ msecs_to_jiffies(data->interval)) || !data->valid) {
int i;
dev_dbg(&client->dev, "Updating lm95245 data.\n");
for (i = 0; i < ARRAY_SIZE(lm95245_reg_address); i++)
data->regs[i]
= i2c_smbus_read_byte_data(client,
......@@ -249,9 +248,9 @@ static ssize_t show_limit(struct device *dev, struct device_attribute *attr,
static ssize_t set_limit(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95245_data *data = i2c_get_clientdata(client);
struct lm95245_data *data = dev_get_drvdata(dev);
int index = to_sensor_dev_attr(attr)->index;
struct i2c_client *client = data->client;
unsigned long val;
if (kstrtoul(buf, 10, &val) < 0)
......@@ -272,27 +271,38 @@ static ssize_t set_limit(struct device *dev, struct device_attribute *attr,
return count;
}
static ssize_t show_crit_hyst(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct lm95245_data *data = lm95245_update_device(dev);
int index = to_sensor_dev_attr(attr)->index;
int hyst = data->regs[index] - data->regs[8];
return snprintf(buf, PAGE_SIZE - 1, "%d\n", hyst * 1000);
}
static ssize_t set_crit_hyst(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95245_data *data = i2c_get_clientdata(client);
struct lm95245_data *data = dev_get_drvdata(dev);
int index = to_sensor_dev_attr(attr)->index;
struct i2c_client *client = data->client;
unsigned long val;
int hyst, limit;
if (kstrtoul(buf, 10, &val) < 0)
return -EINVAL;
val /= 1000;
val = clamp_val(val, 0, 31);
mutex_lock(&data->update_lock);
data->valid = 0;
limit = i2c_smbus_read_byte_data(client, lm95245_reg_address[index]);
hyst = limit - val / 1000;
hyst = clamp_val(hyst, 0, 31);
data->regs[8] = hyst;
/* shared crit hysteresis */
i2c_smbus_write_byte_data(client, LM95245_REG_RW_COMMON_HYSTERESIS,
val);
hyst);
mutex_unlock(&data->update_lock);
......@@ -302,8 +312,7 @@ static ssize_t set_crit_hyst(struct device *dev, struct device_attribute *attr,
static ssize_t show_type(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95245_data *data = i2c_get_clientdata(client);
struct lm95245_data *data = dev_get_drvdata(dev);
return snprintf(buf, PAGE_SIZE - 1,
data->config2 & CFG2_REMOTE_TT ? "1\n" : "2\n");
......@@ -312,8 +321,8 @@ static ssize_t show_type(struct device *dev, struct device_attribute *attr,
static ssize_t set_type(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95245_data *data = i2c_get_clientdata(client);
struct lm95245_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
unsigned long val;
if (kstrtoul(buf, 10, &val) < 0)
......@@ -359,8 +368,8 @@ static ssize_t show_interval(struct device *dev, struct device_attribute *attr,
static ssize_t set_interval(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct lm95245_data *data = i2c_get_clientdata(client);
struct lm95245_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
unsigned long val;
if (kstrtoul(buf, 10, &val) < 0)
......@@ -378,16 +387,15 @@ static ssize_t set_interval(struct device *dev, struct device_attribute *attr,
static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_input, NULL, 0);
static SENSOR_DEVICE_ATTR(temp1_crit, S_IWUSR | S_IRUGO, show_limit,
set_limit, 6);
static SENSOR_DEVICE_ATTR(temp1_crit_hyst, S_IWUSR | S_IRUGO, show_limit,
set_crit_hyst, 8);
static SENSOR_DEVICE_ATTR(temp1_crit_hyst, S_IWUSR | S_IRUGO, show_crit_hyst,
set_crit_hyst, 6);
static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL,
STATUS1_LOC);
static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_input, NULL, 2);
static SENSOR_DEVICE_ATTR(temp2_crit, S_IWUSR | S_IRUGO, show_limit,
set_limit, 7);
static SENSOR_DEVICE_ATTR(temp2_crit_hyst, S_IWUSR | S_IRUGO, show_limit,
set_crit_hyst, 8);
static SENSOR_DEVICE_ATTR(temp2_crit_hyst, S_IRUGO, show_crit_hyst, NULL, 7);
static SENSOR_DEVICE_ATTR(temp2_crit_alarm, S_IRUGO, show_alarm, NULL,
STATUS1_RTCRIT);
static SENSOR_DEVICE_ATTR(temp2_type, S_IWUSR | S_IRUGO, show_type,
......@@ -398,7 +406,7 @@ static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL,
static DEVICE_ATTR(update_interval, S_IWUSR | S_IRUGO, show_interval,
set_interval);
static struct attribute *lm95245_attributes[] = {
static struct attribute *lm95245_attrs[] = {
&sensor_dev_attr_temp1_input.dev_attr.attr,
&sensor_dev_attr_temp1_crit.dev_attr.attr,
&sensor_dev_attr_temp1_crit_hyst.dev_attr.attr,
......@@ -412,10 +420,7 @@ static struct attribute *lm95245_attributes[] = {
&dev_attr_update_interval.attr,
NULL
};
static const struct attribute_group lm95245_group = {
.attrs = lm95245_attributes,
};
ATTRIBUTE_GROUPS(lm95245);
/* Return 0 if detection is successful, -ENODEV otherwise */
static int lm95245_detect(struct i2c_client *new_client,
......@@ -436,11 +441,9 @@ static int lm95245_detect(struct i2c_client *new_client,
return 0;
}
static void lm95245_init_client(struct i2c_client *client)
static void lm95245_init_client(struct i2c_client *client,
struct lm95245_data *data)
{
struct lm95245_data *data = i2c_get_clientdata(client);
data->valid = 0;
data->interval = lm95245_read_conversion_rate(client);
data->config1 = i2c_smbus_read_byte_data(client,
......@@ -456,49 +459,27 @@ static void lm95245_init_client(struct i2c_client *client)
}
}
static int lm95245_probe(struct i2c_client *new_client,
static int lm95245_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct device *dev = &client->dev;
struct lm95245_data *data;
int err;
struct device *hwmon_dev;
data = devm_kzalloc(&new_client->dev, sizeof(struct lm95245_data),
GFP_KERNEL);
data = devm_kzalloc(dev, sizeof(struct lm95245_data), GFP_KERNEL);
if (!data)
return -ENOMEM;
i2c_set_clientdata(new_client, data);
data->client = client;
mutex_init(&data->update_lock);
/* Initialize the LM95245 chip */
lm95245_init_client(new_client);
/* Register sysfs hooks */
err = sysfs_create_group(&new_client->dev.kobj, &lm95245_group);
if (err)
return err;
data->hwmon_dev = hwmon_device_register(&new_client->dev);
if (IS_ERR(data->hwmon_dev)) {
err = PTR_ERR(data->hwmon_dev);
goto exit_remove_files;
}
return 0;
exit_remove_files:
sysfs_remove_group(&new_client->dev.kobj, &lm95245_group);
return err;
}
lm95245_init_client(client, data);
static int lm95245_remove(struct i2c_client *client)
{
struct lm95245_data *data = i2c_get_clientdata(client);
hwmon_device_unregister(data->hwmon_dev);
sysfs_remove_group(&client->dev.kobj, &lm95245_group);
return 0;
hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
data,
lm95245_groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
}
/* Driver data (common to all clients) */
......@@ -514,7 +495,6 @@ static struct i2c_driver lm95245_driver = {
.name = DEVNAME,
},
.probe = lm95245_probe,
.remove = lm95245_remove,
.id_table = lm95245_id,
.detect = lm95245_detect,
.address_list = normal_i2c,
......
/*
* Driver for Linear Technology LTC2945 I2C Power Monitor
*
* Copyright (c) 2014 Guenter Roeck
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/err.h>
#include <linux/slab.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/jiffies.h>
#include <linux/regmap.h>
/* chip registers */
#define LTC2945_CONTROL 0x00
#define LTC2945_ALERT 0x01
#define LTC2945_STATUS 0x02
#define LTC2945_FAULT 0x03
#define LTC2945_POWER_H 0x05
#define LTC2945_MAX_POWER_H 0x08
#define LTC2945_MIN_POWER_H 0x0b
#define LTC2945_MAX_POWER_THRES_H 0x0e
#define LTC2945_MIN_POWER_THRES_H 0x11
#define LTC2945_SENSE_H 0x14
#define LTC2945_MAX_SENSE_H 0x16
#define LTC2945_MIN_SENSE_H 0x18
#define LTC2945_MAX_SENSE_THRES_H 0x1a
#define LTC2945_MIN_SENSE_THRES_H 0x1c
#define LTC2945_VIN_H 0x1e
#define LTC2945_MAX_VIN_H 0x20
#define LTC2945_MIN_VIN_H 0x22
#define LTC2945_MAX_VIN_THRES_H 0x24
#define LTC2945_MIN_VIN_THRES_H 0x26
#define LTC2945_ADIN_H 0x28
#define LTC2945_MAX_ADIN_H 0x2a
#define LTC2945_MIN_ADIN_H 0x2c
#define LTC2945_MAX_ADIN_THRES_H 0x2e
#define LTC2945_MIN_ADIN_THRES_H 0x30
#define LTC2945_MIN_ADIN_THRES_L 0x31
/* Fault register bits */
#define FAULT_ADIN_UV (1 << 0)
#define FAULT_ADIN_OV (1 << 1)
#define FAULT_VIN_UV (1 << 2)
#define FAULT_VIN_OV (1 << 3)
#define FAULT_SENSE_UV (1 << 4)
#define FAULT_SENSE_OV (1 << 5)
#define FAULT_POWER_UV (1 << 6)
#define FAULT_POWER_OV (1 << 7)
/* Control register bits */
#define CONTROL_MULT_SELECT (1 << 0)
#define CONTROL_TEST_MODE (1 << 4)
static inline bool is_power_reg(u8 reg)
{
return reg < LTC2945_SENSE_H;
}
/* Return the value from the given register in uW, mV, or mA */
static long long ltc2945_reg_to_val(struct device *dev, u8 reg)
{
struct regmap *regmap = dev_get_drvdata(dev);
unsigned int control;
u8 buf[3];
long long val;
int ret;
ret = regmap_bulk_read(regmap, reg, buf,
is_power_reg(reg) ? 3 : 2);
if (ret < 0)
return ret;
if (is_power_reg(reg)) {
/* power */
val = (buf[0] << 16) + (buf[1] << 8) + buf[2];
} else {
/* current, voltage */
val = (buf[0] << 4) + (buf[1] >> 4);
}
switch (reg) {
case LTC2945_POWER_H:
case LTC2945_MAX_POWER_H:
case LTC2945_MIN_POWER_H:
case LTC2945_MAX_POWER_THRES_H:
case LTC2945_MIN_POWER_THRES_H:
/*
* Convert to uW by assuming current is measured with
* an 1mOhm sense resistor, similar to current
* measurements.
* Control register bit 0 selects if voltage at SENSE+/VDD
* or voltage at ADIN is used to measure power.
*/
ret = regmap_read(regmap, LTC2945_CONTROL, &control);
if (ret < 0)
return ret;
if (control & CONTROL_MULT_SELECT) {
/* 25 mV * 25 uV = 0.625 uV resolution. */
val *= 625LL;
} else {
/* 0.5 mV * 25 uV = 0.0125 uV resolution. */
val = (val * 25LL) >> 1;
}
break;
case LTC2945_VIN_H:
case LTC2945_MAX_VIN_H:
case LTC2945_MIN_VIN_H:
case LTC2945_MAX_VIN_THRES_H:
case LTC2945_MIN_VIN_THRES_H:
/* 25 mV resolution. Convert to mV. */
val *= 25;
break;
case LTC2945_ADIN_H:
case LTC2945_MAX_ADIN_H:
case LTC2945_MIN_ADIN_THRES_H:
case LTC2945_MAX_ADIN_THRES_H:
case LTC2945_MIN_ADIN_H:
/* 0.5mV resolution. Convert to mV. */
val = val >> 1;
break;
case LTC2945_SENSE_H:
case LTC2945_MAX_SENSE_H:
case LTC2945_MIN_SENSE_H:
case LTC2945_MAX_SENSE_THRES_H:
case LTC2945_MIN_SENSE_THRES_H:
/*
* 25 uV resolution. Convert to current as measured with
* an 1 mOhm sense resistor, in mA. If a different sense
* resistor is installed, calculate the actual current by
* dividing the reported current by the sense resistor value
* in mOhm.
*/
val *= 25;
break;
default:
return -EINVAL;
}
return val;
}
static int ltc2945_val_to_reg(struct device *dev, u8 reg,
unsigned long val)
{
struct regmap *regmap = dev_get_drvdata(dev);
unsigned int control;
int ret;
switch (reg) {
case LTC2945_POWER_H:
case LTC2945_MAX_POWER_H:
case LTC2945_MIN_POWER_H:
case LTC2945_MAX_POWER_THRES_H:
case LTC2945_MIN_POWER_THRES_H:
/*
* Convert to register value by assuming current is measured
* with an 1mOhm sense resistor, similar to current
* measurements.
* Control register bit 0 selects if voltage at SENSE+/VDD
* or voltage at ADIN is used to measure power, which in turn
* determines register calculations.
*/
ret = regmap_read(regmap, LTC2945_CONTROL, &control);
if (ret < 0)
return ret;
if (control & CONTROL_MULT_SELECT) {
/* 25 mV * 25 uV = 0.625 uV resolution. */
val = DIV_ROUND_CLOSEST(val, 625);
} else {
/*
* 0.5 mV * 25 uV = 0.0125 uV resolution.
* Divide first to avoid overflow;
* accept loss of accuracy.
*/
val = DIV_ROUND_CLOSEST(val, 25) * 2;
}
break;
case LTC2945_VIN_H:
case LTC2945_MAX_VIN_H:
case LTC2945_MIN_VIN_H:
case LTC2945_MAX_VIN_THRES_H:
case LTC2945_MIN_VIN_THRES_H:
/* 25 mV resolution. */
val /= 25;
break;
case LTC2945_ADIN_H:
case LTC2945_MAX_ADIN_H:
case LTC2945_MIN_ADIN_THRES_H:
case LTC2945_MAX_ADIN_THRES_H:
case LTC2945_MIN_ADIN_H:
/* 0.5mV resolution. */
val *= 2;
break;
case LTC2945_SENSE_H:
case LTC2945_MAX_SENSE_H:
case LTC2945_MIN_SENSE_H:
case LTC2945_MAX_SENSE_THRES_H:
case LTC2945_MIN_SENSE_THRES_H:
/*
* 25 uV resolution. Convert to current as measured with
* an 1 mOhm sense resistor, in mA. If a different sense
* resistor is installed, calculate the actual current by
* dividing the reported current by the sense resistor value
* in mOhm.
*/
val = DIV_ROUND_CLOSEST(val, 25);
break;
default:
return -EINVAL;
}
return val;
}
static ssize_t ltc2945_show_value(struct device *dev,
struct device_attribute *da, char *buf)
{
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
long long value;
value = ltc2945_reg_to_val(dev, attr->index);
if (value < 0)
return value;
return snprintf(buf, PAGE_SIZE, "%lld\n", value);
}
static ssize_t ltc2945_set_value(struct device *dev,
struct device_attribute *da,
const char *buf, size_t count)
{
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
struct regmap *regmap = dev_get_drvdata(dev);
u8 reg = attr->index;
unsigned long val;
u8 regbuf[3];
int num_regs;
int regval;
int ret;
ret = kstrtoul(buf, 10, &val);
if (ret)
return ret;
/* convert to register value, then clamp and write result */
regval = ltc2945_val_to_reg(dev, reg, val);
if (is_power_reg(reg)) {
regval = clamp_val(regval, 0, 0xffffff);
regbuf[0] = regval >> 16;
regbuf[1] = (regval >> 8) & 0xff;
regbuf[2] = regval;
num_regs = 3;
} else {
regval = clamp_val(regval, 0, 0xfff) << 4;
regbuf[0] = regval >> 8;
regbuf[1] = regval & 0xff;
num_regs = 2;
}
ret = regmap_bulk_write(regmap, reg, regbuf, num_regs);
return ret < 0 ? ret : count;
}
static ssize_t ltc2945_reset_history(struct device *dev,
struct device_attribute *da,
const char *buf, size_t count)
{
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
struct regmap *regmap = dev_get_drvdata(dev);
u8 reg = attr->index;
int num_regs = is_power_reg(reg) ? 3 : 2;
u8 buf_min[3] = { 0xff, 0xff, 0xff };
u8 buf_max[3] = { 0, 0, 0 };
unsigned long val;
int ret;
ret = kstrtoul(buf, 10, &val);
if (ret)
return ret;
if (val != 1)
return -EINVAL;
ret = regmap_update_bits(regmap, LTC2945_CONTROL, CONTROL_TEST_MODE,
CONTROL_TEST_MODE);
/* Reset minimum */
ret = regmap_bulk_write(regmap, reg, buf_min, num_regs);
if (ret)
return ret;
switch (reg) {
case LTC2945_MIN_POWER_H:
reg = LTC2945_MAX_POWER_H;
break;
case LTC2945_MIN_SENSE_H:
reg = LTC2945_MAX_SENSE_H;
break;
case LTC2945_MIN_VIN_H:
reg = LTC2945_MAX_VIN_H;
break;
case LTC2945_MIN_ADIN_H:
reg = LTC2945_MAX_ADIN_H;
break;
default:
BUG();
break;
}
/* Reset maximum */
ret = regmap_bulk_write(regmap, reg, buf_max, num_regs);
/* Try resetting test mode even if there was an error */
regmap_update_bits(regmap, LTC2945_CONTROL, CONTROL_TEST_MODE, 0);
return ret ? : count;
}
static ssize_t ltc2945_show_bool(struct device *dev,
struct device_attribute *da, char *buf)
{
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
struct regmap *regmap = dev_get_drvdata(dev);
unsigned int fault;
int ret;
ret = regmap_read(regmap, LTC2945_FAULT, &fault);
if (ret < 0)
return ret;
fault &= attr->index;
if (fault) /* Clear reported faults in chip register */
regmap_update_bits(regmap, LTC2945_FAULT, attr->index, 0);
return snprintf(buf, PAGE_SIZE, "%d\n", !!fault);
}
/* Input voltages */
static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, ltc2945_show_value, NULL,
LTC2945_VIN_H);
static SENSOR_DEVICE_ATTR(in1_min, S_IRUGO | S_IWUSR, ltc2945_show_value,
ltc2945_set_value, LTC2945_MIN_VIN_THRES_H);
static SENSOR_DEVICE_ATTR(in1_max, S_IRUGO | S_IWUSR, ltc2945_show_value,
ltc2945_set_value, LTC2945_MAX_VIN_THRES_H);
static SENSOR_DEVICE_ATTR(in1_lowest, S_IRUGO, ltc2945_show_value, NULL,
LTC2945_MIN_VIN_H);
static SENSOR_DEVICE_ATTR(in1_highest, S_IRUGO, ltc2945_show_value, NULL,
LTC2945_MAX_VIN_H);
static SENSOR_DEVICE_ATTR(in1_reset_history, S_IWUSR, NULL,
ltc2945_reset_history, LTC2945_MIN_VIN_H);
static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, ltc2945_show_value, NULL,
LTC2945_ADIN_H);
static SENSOR_DEVICE_ATTR(in2_min, S_IRUGO | S_IWUSR, ltc2945_show_value,
ltc2945_set_value, LTC2945_MIN_ADIN_THRES_H);
static SENSOR_DEVICE_ATTR(in2_max, S_IRUGO | S_IWUSR, ltc2945_show_value,
ltc2945_set_value, LTC2945_MAX_ADIN_THRES_H);
static SENSOR_DEVICE_ATTR(in2_lowest, S_IRUGO, ltc2945_show_value, NULL,
LTC2945_MIN_ADIN_H);
static SENSOR_DEVICE_ATTR(in2_highest, S_IRUGO, ltc2945_show_value, NULL,
LTC2945_MAX_ADIN_H);
static SENSOR_DEVICE_ATTR(in2_reset_history, S_IWUSR, NULL,
ltc2945_reset_history, LTC2945_MIN_ADIN_H);
/* Voltage alarms */
static SENSOR_DEVICE_ATTR(in1_min_alarm, S_IRUGO, ltc2945_show_bool, NULL,
FAULT_VIN_UV);
static SENSOR_DEVICE_ATTR(in1_max_alarm, S_IRUGO, ltc2945_show_bool, NULL,
FAULT_VIN_OV);
static SENSOR_DEVICE_ATTR(in2_min_alarm, S_IRUGO, ltc2945_show_bool, NULL,
FAULT_ADIN_UV);
static SENSOR_DEVICE_ATTR(in2_max_alarm, S_IRUGO, ltc2945_show_bool, NULL,
FAULT_ADIN_OV);
/* Currents (via sense resistor) */
static SENSOR_DEVICE_ATTR(curr1_input, S_IRUGO, ltc2945_show_value, NULL,
LTC2945_SENSE_H);
static SENSOR_DEVICE_ATTR(curr1_min, S_IRUGO | S_IWUSR, ltc2945_show_value,
ltc2945_set_value, LTC2945_MIN_SENSE_THRES_H);
static SENSOR_DEVICE_ATTR(curr1_max, S_IRUGO | S_IWUSR, ltc2945_show_value,
ltc2945_set_value, LTC2945_MAX_SENSE_THRES_H);
static SENSOR_DEVICE_ATTR(curr1_lowest, S_IRUGO, ltc2945_show_value, NULL,
LTC2945_MIN_SENSE_H);
static SENSOR_DEVICE_ATTR(curr1_highest, S_IRUGO, ltc2945_show_value, NULL,
LTC2945_MAX_SENSE_H);
static SENSOR_DEVICE_ATTR(curr1_reset_history, S_IWUSR, NULL,
ltc2945_reset_history, LTC2945_MIN_SENSE_H);
/* Current alarms */
static SENSOR_DEVICE_ATTR(curr1_min_alarm, S_IRUGO, ltc2945_show_bool, NULL,
FAULT_SENSE_UV);
static SENSOR_DEVICE_ATTR(curr1_max_alarm, S_IRUGO, ltc2945_show_bool, NULL,
FAULT_SENSE_OV);
/* Power */
static SENSOR_DEVICE_ATTR(power1_input, S_IRUGO, ltc2945_show_value, NULL,
LTC2945_POWER_H);
static SENSOR_DEVICE_ATTR(power1_min, S_IRUGO | S_IWUSR, ltc2945_show_value,
ltc2945_set_value, LTC2945_MIN_POWER_THRES_H);
static SENSOR_DEVICE_ATTR(power1_max, S_IRUGO | S_IWUSR, ltc2945_show_value,
ltc2945_set_value, LTC2945_MAX_POWER_THRES_H);
static SENSOR_DEVICE_ATTR(power1_input_lowest, S_IRUGO, ltc2945_show_value,
NULL, LTC2945_MIN_POWER_H);
static SENSOR_DEVICE_ATTR(power1_input_highest, S_IRUGO, ltc2945_show_value,
NULL, LTC2945_MAX_POWER_H);
static SENSOR_DEVICE_ATTR(power1_reset_history, S_IWUSR, NULL,
ltc2945_reset_history, LTC2945_MIN_POWER_H);
/* Power alarms */
static SENSOR_DEVICE_ATTR(power1_min_alarm, S_IRUGO, ltc2945_show_bool, NULL,
FAULT_POWER_UV);
static SENSOR_DEVICE_ATTR(power1_max_alarm, S_IRUGO, ltc2945_show_bool, NULL,
FAULT_POWER_OV);
static struct attribute *ltc2945_attrs[] = {
&sensor_dev_attr_in1_input.dev_attr.attr,
&sensor_dev_attr_in1_min.dev_attr.attr,
&sensor_dev_attr_in1_max.dev_attr.attr,
&sensor_dev_attr_in1_lowest.dev_attr.attr,
&sensor_dev_attr_in1_highest.dev_attr.attr,
&sensor_dev_attr_in1_reset_history.dev_attr.attr,
&sensor_dev_attr_in1_min_alarm.dev_attr.attr,
&sensor_dev_attr_in1_max_alarm.dev_attr.attr,
&sensor_dev_attr_in2_input.dev_attr.attr,
&sensor_dev_attr_in2_min.dev_attr.attr,
&sensor_dev_attr_in2_max.dev_attr.attr,
&sensor_dev_attr_in2_lowest.dev_attr.attr,
&sensor_dev_attr_in2_highest.dev_attr.attr,
&sensor_dev_attr_in2_reset_history.dev_attr.attr,
&sensor_dev_attr_in2_min_alarm.dev_attr.attr,
&sensor_dev_attr_in2_max_alarm.dev_attr.attr,
&sensor_dev_attr_curr1_input.dev_attr.attr,
&sensor_dev_attr_curr1_min.dev_attr.attr,
&sensor_dev_attr_curr1_max.dev_attr.attr,
&sensor_dev_attr_curr1_lowest.dev_attr.attr,
&sensor_dev_attr_curr1_highest.dev_attr.attr,
&sensor_dev_attr_curr1_reset_history.dev_attr.attr,
&sensor_dev_attr_curr1_min_alarm.dev_attr.attr,
&sensor_dev_attr_curr1_max_alarm.dev_attr.attr,
&sensor_dev_attr_power1_input.dev_attr.attr,
&sensor_dev_attr_power1_min.dev_attr.attr,
&sensor_dev_attr_power1_max.dev_attr.attr,
&sensor_dev_attr_power1_input_lowest.dev_attr.attr,
&sensor_dev_attr_power1_input_highest.dev_attr.attr,
&sensor_dev_attr_power1_reset_history.dev_attr.attr,
&sensor_dev_attr_power1_min_alarm.dev_attr.attr,
&sensor_dev_attr_power1_max_alarm.dev_attr.attr,
NULL,
};
ATTRIBUTE_GROUPS(ltc2945);
static struct regmap_config ltc2945_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
.max_register = LTC2945_MIN_ADIN_THRES_L,
};
static int ltc2945_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct device *dev = &client->dev;
struct device *hwmon_dev;
struct regmap *regmap;
regmap = devm_regmap_init_i2c(client, &ltc2945_regmap_config);
if (IS_ERR(regmap)) {
dev_err(dev, "failed to allocate register map\n");
return PTR_ERR(regmap);
}
/* Clear faults */
regmap_write(regmap, LTC2945_FAULT, 0x00);
hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
regmap,
ltc2945_groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
}
static const struct i2c_device_id ltc2945_id[] = {
{"ltc2945", 0},
{ }
};
MODULE_DEVICE_TABLE(i2c, ltc2945_id);
static struct i2c_driver ltc2945_driver = {
.driver = {
.name = "ltc2945",
},
.probe = ltc2945_probe,
.id_table = ltc2945_id,
};
module_i2c_driver(ltc2945_driver);
MODULE_AUTHOR("Guenter Roeck <linux@roeck-us.net>");
MODULE_DESCRIPTION("LTC2945 driver");
MODULE_LICENSE("GPL");
......@@ -33,7 +33,7 @@ enum ltc4215_cmd {
};
struct ltc4215_data {
struct device *hwmon_dev;
struct i2c_client *client;
struct mutex update_lock;
bool valid;
......@@ -45,8 +45,8 @@ struct ltc4215_data {
static struct ltc4215_data *ltc4215_update_device(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct ltc4215_data *data = i2c_get_clientdata(client);
struct ltc4215_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
s32 val;
int i;
......@@ -214,7 +214,7 @@ static SENSOR_DEVICE_ATTR(in2_min_alarm, S_IRUGO, ltc4215_show_alarm, NULL,
* Finally, construct an array of pointers to members of the above objects,
* as required for sysfs_create_group()
*/
static struct attribute *ltc4215_attributes[] = {
static struct attribute *ltc4215_attrs[] = {
&sensor_dev_attr_curr1_input.dev_attr.attr,
&sensor_dev_attr_curr1_max_alarm.dev_attr.attr,
......@@ -229,57 +229,33 @@ static struct attribute *ltc4215_attributes[] = {
NULL,
};
static const struct attribute_group ltc4215_group = {
.attrs = ltc4215_attributes,
};
ATTRIBUTE_GROUPS(ltc4215);
static int ltc4215_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct i2c_adapter *adapter = client->adapter;
struct device *dev = &client->dev;
struct ltc4215_data *data;
int ret;
struct device *hwmon_dev;
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
return -ENODEV;
data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
if (!data)
return -ENOMEM;
i2c_set_clientdata(client, data);
data->client = client;
mutex_init(&data->update_lock);
/* Initialize the LTC4215 chip */
i2c_smbus_write_byte_data(client, LTC4215_FAULT, 0x00);
/* Register sysfs hooks */
ret = sysfs_create_group(&client->dev.kobj, &ltc4215_group);
if (ret)
return ret;
data->hwmon_dev = hwmon_device_register(&client->dev);
if (IS_ERR(data->hwmon_dev)) {
ret = PTR_ERR(data->hwmon_dev);
goto out_hwmon_device_register;
}
return 0;
out_hwmon_device_register:
sysfs_remove_group(&client->dev.kobj, &ltc4215_group);
return ret;
}
static int ltc4215_remove(struct i2c_client *client)
{
struct ltc4215_data *data = i2c_get_clientdata(client);
hwmon_device_unregister(data->hwmon_dev);
sysfs_remove_group(&client->dev.kobj, &ltc4215_group);
return 0;
hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
data,
ltc4215_groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
}
static const struct i2c_device_id ltc4215_id[] = {
......@@ -294,7 +270,6 @@ static struct i2c_driver ltc4215_driver = {
.name = "ltc4215",
},
.probe = ltc4215_probe,
.remove = ltc4215_remove,
.id_table = ltc4215_id,
};
......
/*
* Driver for Linear Technology LTC4222 Dual Hot Swap controller
*
* Copyright (c) 2014 Guenter Roeck
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/err.h>
#include <linux/slab.h>
#include <linux/bitops.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/jiffies.h>
#include <linux/regmap.h>
/* chip registers */
#define LTC4222_CONTROL1 0xd0
#define LTC4222_ALERT1 0xd1
#define LTC4222_STATUS1 0xd2
#define LTC4222_FAULT1 0xd3
#define LTC4222_CONTROL2 0xd4
#define LTC4222_ALERT2 0xd5
#define LTC4222_STATUS2 0xd6
#define LTC4222_FAULT2 0xd7
#define LTC4222_SOURCE1 0xd8
#define LTC4222_SOURCE2 0xda
#define LTC4222_ADIN1 0xdc
#define LTC4222_ADIN2 0xde
#define LTC4222_SENSE1 0xe0
#define LTC4222_SENSE2 0xe2
#define LTC4222_ADC_CONTROL 0xe4
/*
* Fault register bits
*/
#define FAULT_OV BIT(0)
#define FAULT_UV BIT(1)
#define FAULT_OC BIT(2)
#define FAULT_POWER_BAD BIT(3)
#define FAULT_FET_BAD BIT(5)
/* Return the voltage from the given register in mV or mA */
static int ltc4222_get_value(struct device *dev, u8 reg)
{
struct regmap *regmap = dev_get_drvdata(dev);
unsigned int val;
u8 buf[2];
int ret;
ret = regmap_bulk_read(regmap, reg, buf, 2);
if (ret < 0)
return ret;
val = ((buf[0] << 8) + buf[1]) >> 6;
switch (reg) {
case LTC4222_ADIN1:
case LTC4222_ADIN2:
/* 1.25 mV resolution. Convert to mV. */
val = DIV_ROUND_CLOSEST(val * 5, 4);
break;
case LTC4222_SOURCE1:
case LTC4222_SOURCE2:
/* 31.25 mV resolution. Convert to mV. */
val = DIV_ROUND_CLOSEST(val * 125, 4);
break;
case LTC4222_SENSE1:
case LTC4222_SENSE2:
/*
* 62.5 uV resolution. Convert to current as measured with
* an 1 mOhm sense resistor, in mA. If a different sense
* resistor is installed, calculate the actual current by
* dividing the reported current by the sense resistor value
* in mOhm.
*/
val = DIV_ROUND_CLOSEST(val * 125, 2);
break;
default:
return -EINVAL;
}
return val;
}
static ssize_t ltc4222_show_value(struct device *dev,
struct device_attribute *da, char *buf)
{
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int value;
value = ltc4222_get_value(dev, attr->index);
if (value < 0)
return value;
return snprintf(buf, PAGE_SIZE, "%d\n", value);
}
static ssize_t ltc4222_show_bool(struct device *dev,
struct device_attribute *da, char *buf)
{
struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(da);
struct regmap *regmap = dev_get_drvdata(dev);
unsigned int fault;
int ret;
ret = regmap_read(regmap, attr->nr, &fault);
if (ret < 0)
return ret;
fault &= attr->index;
if (fault) /* Clear reported faults in chip register */
regmap_update_bits(regmap, attr->nr, attr->index, 0);
return snprintf(buf, PAGE_SIZE, "%d\n", !!fault);
}
/* Voltages */
static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, ltc4222_show_value, NULL,
LTC4222_SOURCE1);
static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, ltc4222_show_value, NULL,
LTC4222_ADIN1);
static SENSOR_DEVICE_ATTR(in3_input, S_IRUGO, ltc4222_show_value, NULL,
LTC4222_SOURCE2);
static SENSOR_DEVICE_ATTR(in4_input, S_IRUGO, ltc4222_show_value, NULL,
LTC4222_ADIN2);
/*
* Voltage alarms
* UV/OV faults are associated with the input voltage, and power bad and fet
* faults are associated with the output voltage.
*/
static SENSOR_DEVICE_ATTR_2(in1_min_alarm, S_IRUGO, ltc4222_show_bool, NULL,
LTC4222_FAULT1, FAULT_UV);
static SENSOR_DEVICE_ATTR_2(in1_max_alarm, S_IRUGO, ltc4222_show_bool, NULL,
LTC4222_FAULT1, FAULT_OV);
static SENSOR_DEVICE_ATTR_2(in2_alarm, S_IRUGO, ltc4222_show_bool, NULL,
LTC4222_FAULT1, FAULT_POWER_BAD | FAULT_FET_BAD);
static SENSOR_DEVICE_ATTR_2(in3_min_alarm, S_IRUGO, ltc4222_show_bool, NULL,
LTC4222_FAULT2, FAULT_UV);
static SENSOR_DEVICE_ATTR_2(in3_max_alarm, S_IRUGO, ltc4222_show_bool, NULL,
LTC4222_FAULT2, FAULT_OV);
static SENSOR_DEVICE_ATTR_2(in4_alarm, S_IRUGO, ltc4222_show_bool, NULL,
LTC4222_FAULT2, FAULT_POWER_BAD | FAULT_FET_BAD);
/* Current (via sense resistor) */
static SENSOR_DEVICE_ATTR(curr1_input, S_IRUGO, ltc4222_show_value, NULL,
LTC4222_SENSE1);
static SENSOR_DEVICE_ATTR(curr2_input, S_IRUGO, ltc4222_show_value, NULL,
LTC4222_SENSE2);
/* Overcurrent alarm */
static SENSOR_DEVICE_ATTR_2(curr1_max_alarm, S_IRUGO, ltc4222_show_bool, NULL,
LTC4222_FAULT1, FAULT_OC);
static SENSOR_DEVICE_ATTR_2(curr2_max_alarm, S_IRUGO, ltc4222_show_bool, NULL,
LTC4222_FAULT2, FAULT_OC);
static struct attribute *ltc4222_attrs[] = {
&sensor_dev_attr_in1_input.dev_attr.attr,
&sensor_dev_attr_in1_min_alarm.dev_attr.attr,
&sensor_dev_attr_in1_max_alarm.dev_attr.attr,
&sensor_dev_attr_in2_input.dev_attr.attr,
&sensor_dev_attr_in2_alarm.dev_attr.attr,
&sensor_dev_attr_in3_input.dev_attr.attr,
&sensor_dev_attr_in3_min_alarm.dev_attr.attr,
&sensor_dev_attr_in3_max_alarm.dev_attr.attr,
&sensor_dev_attr_in4_input.dev_attr.attr,
&sensor_dev_attr_in4_alarm.dev_attr.attr,
&sensor_dev_attr_curr1_input.dev_attr.attr,
&sensor_dev_attr_curr1_max_alarm.dev_attr.attr,
&sensor_dev_attr_curr2_input.dev_attr.attr,
&sensor_dev_attr_curr2_max_alarm.dev_attr.attr,
NULL,
};
ATTRIBUTE_GROUPS(ltc4222);
static struct regmap_config ltc4222_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
.max_register = LTC4222_ADC_CONTROL,
};
static int ltc4222_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct device *dev = &client->dev;
struct device *hwmon_dev;
struct regmap *regmap;
regmap = devm_regmap_init_i2c(client, &ltc4222_regmap_config);
if (IS_ERR(regmap)) {
dev_err(dev, "failed to allocate register map\n");
return PTR_ERR(regmap);
}
/* Clear faults */
regmap_write(regmap, LTC4222_FAULT1, 0x00);
regmap_write(regmap, LTC4222_FAULT2, 0x00);
hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
regmap,
ltc4222_groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
}
static const struct i2c_device_id ltc4222_id[] = {
{"ltc4222", 0},
{ }
};
MODULE_DEVICE_TABLE(i2c, ltc4222_id);
static struct i2c_driver ltc4222_driver = {
.driver = {
.name = "ltc4222",
},
.probe = ltc4222_probe,
.id_table = ltc4222_id,
};
module_i2c_driver(ltc4222_driver);
MODULE_AUTHOR("Guenter Roeck <linux@roeck-us.net>");
MODULE_DESCRIPTION("LTC4222 driver");
MODULE_LICENSE("GPL");
......@@ -95,7 +95,6 @@ static void ltc4245_update_gpios(struct device *dev)
* readings as stale by setting them to -EAGAIN
*/
if (time_after(jiffies, data->last_updated + 5 * HZ)) {
dev_dbg(&client->dev, "Marking GPIOs invalid\n");
for (i = 0; i < ARRAY_SIZE(data->gpios); i++)
data->gpios[i] = -EAGAIN;
}
......@@ -141,8 +140,6 @@ static struct ltc4245_data *ltc4245_update_device(struct device *dev)
if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
dev_dbg(&client->dev, "Starting ltc4245 update\n");
/* Read control registers -- 0x00 to 0x07 */
for (i = 0; i < ARRAY_SIZE(data->cregs); i++) {
val = i2c_smbus_read_byte_data(client, i);
......@@ -470,19 +467,15 @@ static void ltc4245_sysfs_add_groups(struct ltc4245_data *data)
static bool ltc4245_use_extra_gpios(struct i2c_client *client)
{
struct ltc4245_platform_data *pdata = dev_get_platdata(&client->dev);
#ifdef CONFIG_OF
struct device_node *np = client->dev.of_node;
#endif
/* prefer platform data */
if (pdata)
return pdata->use_extra_gpios;
#ifdef CONFIG_OF
/* fallback on OF */
if (of_find_property(np, "ltc4245,use-extra-gpios", NULL))
return true;
#endif
return false;
}
......@@ -512,24 +505,10 @@ static int ltc4245_probe(struct i2c_client *client,
/* Add sysfs hooks */
ltc4245_sysfs_add_groups(data);
hwmon_dev = hwmon_device_register_with_groups(&client->dev,
client->name, data,
data->groups);
if (IS_ERR(hwmon_dev))
return PTR_ERR(hwmon_dev);
i2c_set_clientdata(client, hwmon_dev);
return 0;
}
static int ltc4245_remove(struct i2c_client *client)
{
struct device *hwmon_dev = i2c_get_clientdata(client);
hwmon_device_unregister(hwmon_dev);
return 0;
hwmon_dev = devm_hwmon_device_register_with_groups(&client->dev,
client->name, data,
data->groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
}
static const struct i2c_device_id ltc4245_id[] = {
......@@ -544,7 +523,6 @@ static struct i2c_driver ltc4245_driver = {
.name = "ltc4245",
},
.probe = ltc4245_probe,
.remove = ltc4245_remove,
.id_table = ltc4245_id,
};
......
/*
* Driver for Linear Technology LTC4260 I2C Positive Voltage Hot Swap Controller
*
* Copyright (c) 2014 Guenter Roeck
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/err.h>
#include <linux/slab.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/jiffies.h>
#include <linux/regmap.h>
/* chip registers */
#define LTC4260_CONTROL 0x00
#define LTC4260_ALERT 0x01
#define LTC4260_STATUS 0x02
#define LTC4260_FAULT 0x03
#define LTC4260_SENSE 0x04
#define LTC4260_SOURCE 0x05
#define LTC4260_ADIN 0x06
/*
* Fault register bits
*/
#define FAULT_OV (1 << 0)
#define FAULT_UV (1 << 1)
#define FAULT_OC (1 << 2)
#define FAULT_POWER_BAD (1 << 3)
#define FAULT_FET_SHORT (1 << 5)
/* Return the voltage from the given register in mV or mA */
static int ltc4260_get_value(struct device *dev, u8 reg)
{
struct regmap *regmap = dev_get_drvdata(dev);
unsigned int val;
int ret;
ret = regmap_read(regmap, reg, &val);
if (ret < 0)
return ret;
switch (reg) {
case LTC4260_ADIN:
/* 10 mV resolution. Convert to mV. */
val = val * 10;
break;
case LTC4260_SOURCE:
/* 400 mV resolution. Convert to mV. */
val = val * 400;
break;
case LTC4260_SENSE:
/*
* 300 uV resolution. Convert to current as measured with
* an 1 mOhm sense resistor, in mA. If a different sense
* resistor is installed, calculate the actual current by
* dividing the reported current by the sense resistor value
* in mOhm.
*/
val = val * 300;
break;
default:
return -EINVAL;
}
return val;
}
static ssize_t ltc4260_show_value(struct device *dev,
struct device_attribute *da, char *buf)
{
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int value;
value = ltc4260_get_value(dev, attr->index);
if (value < 0)
return value;
return snprintf(buf, PAGE_SIZE, "%d\n", value);
}
static ssize_t ltc4260_show_bool(struct device *dev,
struct device_attribute *da, char *buf)
{
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
struct regmap *regmap = dev_get_drvdata(dev);
unsigned int fault;
int ret;
ret = regmap_read(regmap, LTC4260_FAULT, &fault);
if (ret < 0)
return ret;
fault &= attr->index;
if (fault) /* Clear reported faults in chip register */
regmap_update_bits(regmap, LTC4260_FAULT, attr->index, 0);
return snprintf(buf, PAGE_SIZE, "%d\n", !!fault);
}
/* Voltages */
static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, ltc4260_show_value, NULL,
LTC4260_SOURCE);
static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, ltc4260_show_value, NULL,
LTC4260_ADIN);
/*
* Voltage alarms
* UV/OV faults are associated with the input voltage, and the POWER BAD and
* FET SHORT faults are associated with the output voltage.
*/
static SENSOR_DEVICE_ATTR(in1_min_alarm, S_IRUGO, ltc4260_show_bool, NULL,
FAULT_UV);
static SENSOR_DEVICE_ATTR(in1_max_alarm, S_IRUGO, ltc4260_show_bool, NULL,
FAULT_OV);
static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, ltc4260_show_bool, NULL,
FAULT_POWER_BAD | FAULT_FET_SHORT);
/* Current (via sense resistor) */
static SENSOR_DEVICE_ATTR(curr1_input, S_IRUGO, ltc4260_show_value, NULL,
LTC4260_SENSE);
/* Overcurrent alarm */
static SENSOR_DEVICE_ATTR(curr1_max_alarm, S_IRUGO, ltc4260_show_bool, NULL,
FAULT_OC);
static struct attribute *ltc4260_attrs[] = {
&sensor_dev_attr_in1_input.dev_attr.attr,
&sensor_dev_attr_in1_min_alarm.dev_attr.attr,
&sensor_dev_attr_in1_max_alarm.dev_attr.attr,
&sensor_dev_attr_in2_input.dev_attr.attr,
&sensor_dev_attr_in2_alarm.dev_attr.attr,
&sensor_dev_attr_curr1_input.dev_attr.attr,
&sensor_dev_attr_curr1_max_alarm.dev_attr.attr,
NULL,
};
ATTRIBUTE_GROUPS(ltc4260);
static struct regmap_config ltc4260_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
.max_register = LTC4260_ADIN,
};
static int ltc4260_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct device *dev = &client->dev;
struct device *hwmon_dev;
struct regmap *regmap;
regmap = devm_regmap_init_i2c(client, &ltc4260_regmap_config);
if (IS_ERR(regmap)) {
dev_err(dev, "failed to allocate register map\n");
return PTR_ERR(regmap);
}
/* Clear faults */
regmap_write(regmap, LTC4260_FAULT, 0x00);
hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
regmap,
ltc4260_groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
}
static const struct i2c_device_id ltc4260_id[] = {
{"ltc4260", 0},
{ }
};
MODULE_DEVICE_TABLE(i2c, ltc4260_id);
static struct i2c_driver ltc4260_driver = {
.driver = {
.name = "ltc4260",
},
.probe = ltc4260_probe,
.id_table = ltc4260_id,
};
module_i2c_driver(ltc4260_driver);
MODULE_AUTHOR("Guenter Roeck <linux@roeck-us.net>");
MODULE_DESCRIPTION("LTC4260 driver");
MODULE_LICENSE("GPL");
......@@ -66,7 +66,8 @@ MODULE_PARM_DESC(read_only, "Don't set any values, read only mode");
enum chips { max1668, max1805, max1989 };
struct max1668_data {
struct device *hwmon_dev;
struct i2c_client *client;
const struct attribute_group *groups[3];
enum chips type;
struct mutex update_lock;
......@@ -82,8 +83,8 @@ struct max1668_data {
static struct max1668_data *max1668_update_device(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct max1668_data *data = i2c_get_clientdata(client);
struct max1668_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
struct max1668_data *ret = data;
s32 val;
int i;
......@@ -205,8 +206,8 @@ static ssize_t set_temp_max(struct device *dev,
const char *buf, size_t count)
{
int index = to_sensor_dev_attr(devattr)->index;
struct i2c_client *client = to_i2c_client(dev);
struct max1668_data *data = i2c_get_clientdata(client);
struct max1668_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
long temp;
int ret;
......@@ -216,10 +217,11 @@ static ssize_t set_temp_max(struct device *dev,
mutex_lock(&data->update_lock);
data->temp_max[index] = clamp_val(temp/1000, -128, 127);
if (i2c_smbus_write_byte_data(client,
ret = i2c_smbus_write_byte_data(client,
MAX1668_REG_LIMH_WR(index),
data->temp_max[index]))
count = -EIO;
data->temp_max[index]);
if (ret < 0)
count = ret;
mutex_unlock(&data->update_lock);
return count;
......@@ -230,8 +232,8 @@ static ssize_t set_temp_min(struct device *dev,
const char *buf, size_t count)
{
int index = to_sensor_dev_attr(devattr)->index;
struct i2c_client *client = to_i2c_client(dev);
struct max1668_data *data = i2c_get_clientdata(client);
struct max1668_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
long temp;
int ret;
......@@ -241,10 +243,11 @@ static ssize_t set_temp_min(struct device *dev,
mutex_lock(&data->update_lock);
data->temp_min[index] = clamp_val(temp/1000, -128, 127);
if (i2c_smbus_write_byte_data(client,
ret = i2c_smbus_write_byte_data(client,
MAX1668_REG_LIML_WR(index),
data->temp_min[index]))
count = -EIO;
data->temp_min[index]);
if (ret < 0)
count = ret;
mutex_unlock(&data->update_lock);
return count;
......@@ -405,60 +408,29 @@ static int max1668_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct i2c_adapter *adapter = client->adapter;
struct device *dev = &client->dev;
struct device *hwmon_dev;
struct max1668_data *data;
int err;
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
return -ENODEV;
data = devm_kzalloc(&client->dev, sizeof(struct max1668_data),
GFP_KERNEL);
data = devm_kzalloc(dev, sizeof(struct max1668_data), GFP_KERNEL);
if (!data)
return -ENOMEM;
i2c_set_clientdata(client, data);
data->client = client;
data->type = id->driver_data;
mutex_init(&data->update_lock);
/* Register sysfs hooks */
err = sysfs_create_group(&client->dev.kobj, &max1668_group_common);
if (err)
return err;
if (data->type == max1668 || data->type == max1989) {
err = sysfs_create_group(&client->dev.kobj,
&max1668_group_unique);
if (err)
goto error_sysrem0;
}
data->hwmon_dev = hwmon_device_register(&client->dev);
if (IS_ERR(data->hwmon_dev)) {
err = PTR_ERR(data->hwmon_dev);
goto error_sysrem1;
}
return 0;
error_sysrem1:
/* sysfs hooks */
data->groups[0] = &max1668_group_common;
if (data->type == max1668 || data->type == max1989)
sysfs_remove_group(&client->dev.kobj, &max1668_group_unique);
error_sysrem0:
sysfs_remove_group(&client->dev.kobj, &max1668_group_common);
return err;
}
static int max1668_remove(struct i2c_client *client)
{
struct max1668_data *data = i2c_get_clientdata(client);
data->groups[1] = &max1668_group_unique;
hwmon_device_unregister(data->hwmon_dev);
if (data->type == max1668 || data->type == max1989)
sysfs_remove_group(&client->dev.kobj, &max1668_group_unique);
sysfs_remove_group(&client->dev.kobj, &max1668_group_common);
return 0;
hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
data, data->groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
}
static const struct i2c_device_id max1668_id[] = {
......@@ -476,7 +448,6 @@ static struct i2c_driver max1668_driver = {
.name = "max1668",
},
.probe = max1668_probe,
.remove = max1668_remove,
.id_table = max1668_id,
.detect = max1668_detect,
.address_list = max1668_addr_list,
......
......@@ -80,7 +80,7 @@ static const int rpm_ranges[] = { 2000, 4000, 8000, 16000 };
* Client data (each client gets its own)
*/
struct max6639_data {
struct device *hwmon_dev;
struct i2c_client *client;
struct mutex update_lock;
char valid; /* !=0 if following fields are valid */
unsigned long last_updated; /* In jiffies */
......@@ -104,8 +104,8 @@ struct max6639_data {
static struct max6639_data *max6639_update_device(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct max6639_data *data = i2c_get_clientdata(client);
struct max6639_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
struct max6639_data *ret = data;
int i;
int status_reg;
......@@ -191,9 +191,8 @@ static ssize_t show_temp_fault(struct device *dev,
static ssize_t show_temp_max(struct device *dev,
struct device_attribute *dev_attr, char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct max6639_data *data = i2c_get_clientdata(client);
struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr);
struct max6639_data *data = dev_get_drvdata(dev);
return sprintf(buf, "%d\n", (data->temp_therm[attr->index] * 1000));
}
......@@ -202,9 +201,9 @@ static ssize_t set_temp_max(struct device *dev,
struct device_attribute *dev_attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct max6639_data *data = i2c_get_clientdata(client);
struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr);
struct max6639_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
unsigned long val;
int res;
......@@ -224,9 +223,8 @@ static ssize_t set_temp_max(struct device *dev,
static ssize_t show_temp_crit(struct device *dev,
struct device_attribute *dev_attr, char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct max6639_data *data = i2c_get_clientdata(client);
struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr);
struct max6639_data *data = dev_get_drvdata(dev);
return sprintf(buf, "%d\n", (data->temp_alert[attr->index] * 1000));
}
......@@ -235,9 +233,9 @@ static ssize_t set_temp_crit(struct device *dev,
struct device_attribute *dev_attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct max6639_data *data = i2c_get_clientdata(client);
struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr);
struct max6639_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
unsigned long val;
int res;
......@@ -258,9 +256,8 @@ static ssize_t show_temp_emergency(struct device *dev,
struct device_attribute *dev_attr,
char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct max6639_data *data = i2c_get_clientdata(client);
struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr);
struct max6639_data *data = dev_get_drvdata(dev);
return sprintf(buf, "%d\n", (data->temp_ot[attr->index] * 1000));
}
......@@ -269,9 +266,9 @@ static ssize_t set_temp_emergency(struct device *dev,
struct device_attribute *dev_attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct max6639_data *data = i2c_get_clientdata(client);
struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr);
struct max6639_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
unsigned long val;
int res;
......@@ -291,9 +288,8 @@ static ssize_t set_temp_emergency(struct device *dev,
static ssize_t show_pwm(struct device *dev,
struct device_attribute *dev_attr, char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
struct max6639_data *data = i2c_get_clientdata(client);
struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr);
struct max6639_data *data = dev_get_drvdata(dev);
return sprintf(buf, "%d\n", data->pwm[attr->index] * 255 / 120);
}
......@@ -302,9 +298,9 @@ static ssize_t set_pwm(struct device *dev,
struct device_attribute *dev_attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct max6639_data *data = i2c_get_clientdata(client);
struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr);
struct max6639_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
unsigned long val;
int res;
......@@ -378,7 +374,7 @@ static SENSOR_DEVICE_ATTR(temp1_emergency_alarm, S_IRUGO, show_alarm, NULL, 5);
static SENSOR_DEVICE_ATTR(temp2_emergency_alarm, S_IRUGO, show_alarm, NULL, 4);
static struct attribute *max6639_attributes[] = {
static struct attribute *max6639_attrs[] = {
&sensor_dev_attr_temp1_input.dev_attr.attr,
&sensor_dev_attr_temp2_input.dev_attr.attr,
&sensor_dev_attr_temp1_fault.dev_attr.attr,
......@@ -403,10 +399,7 @@ static struct attribute *max6639_attributes[] = {
&sensor_dev_attr_temp2_emergency_alarm.dev_attr.attr,
NULL
};
static const struct attribute_group max6639_group = {
.attrs = max6639_attributes,
};
ATTRIBUTE_GROUPS(max6639);
/*
* returns respective index in rpm_ranges table
......@@ -424,9 +417,9 @@ static int rpm_range_to_reg(int range)
return 1; /* default: 4000 RPM */
}
static int max6639_init_client(struct i2c_client *client)
static int max6639_init_client(struct i2c_client *client,
struct max6639_data *data)
{
struct max6639_data *data = i2c_get_clientdata(client);
struct max6639_platform_data *max6639_info =
dev_get_platdata(&client->dev);
int i;
......@@ -545,50 +538,27 @@ static int max6639_detect(struct i2c_client *client,
static int max6639_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct device *dev = &client->dev;
struct max6639_data *data;
struct device *hwmon_dev;
int err;
data = devm_kzalloc(&client->dev, sizeof(struct max6639_data),
GFP_KERNEL);
data = devm_kzalloc(dev, sizeof(struct max6639_data), GFP_KERNEL);
if (!data)
return -ENOMEM;
i2c_set_clientdata(client, data);
data->client = client;
mutex_init(&data->update_lock);
/* Initialize the max6639 chip */
err = max6639_init_client(client);
err = max6639_init_client(client, data);
if (err < 0)
return err;
/* Register sysfs hooks */
err = sysfs_create_group(&client->dev.kobj, &max6639_group);
if (err)
return err;
data->hwmon_dev = hwmon_device_register(&client->dev);
if (IS_ERR(data->hwmon_dev)) {
err = PTR_ERR(data->hwmon_dev);
goto error_remove;
}
dev_info(&client->dev, "temperature sensor and fan control found\n");
return 0;
error_remove:
sysfs_remove_group(&client->dev.kobj, &max6639_group);
return err;
}
static int max6639_remove(struct i2c_client *client)
{
struct max6639_data *data = i2c_get_clientdata(client);
hwmon_device_unregister(data->hwmon_dev);
sysfs_remove_group(&client->dev.kobj, &max6639_group);
return 0;
hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
data,
max6639_groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
}
#ifdef CONFIG_PM_SLEEP
......@@ -622,9 +592,7 @@ static const struct i2c_device_id max6639_id[] = {
MODULE_DEVICE_TABLE(i2c, max6639_id);
static const struct dev_pm_ops max6639_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(max6639_suspend, max6639_resume)
};
static SIMPLE_DEV_PM_OPS(max6639_pm_ops, max6639_suspend, max6639_resume);
static struct i2c_driver max6639_driver = {
.class = I2C_CLASS_HWMON,
......@@ -633,7 +601,6 @@ static struct i2c_driver max6639_driver = {
.pm = &max6639_pm_ops,
},
.probe = max6639_probe,
.remove = max6639_remove,
.id_table = max6639_id,
.detect = max6639_detect,
.address_list = normal_i2c,
......
......@@ -105,38 +105,13 @@ module_param(clock, int, S_IRUGO);
#define DIV_FROM_REG(reg) (1 << (reg & 7))
static int max6650_probe(struct i2c_client *client,
const struct i2c_device_id *id);
static int max6650_init_client(struct i2c_client *client);
static int max6650_remove(struct i2c_client *client);
static struct max6650_data *max6650_update_device(struct device *dev);
/*
* Driver data (common to all clients)
*/
static const struct i2c_device_id max6650_id[] = {
{ "max6650", 1 },
{ "max6651", 4 },
{ }
};
MODULE_DEVICE_TABLE(i2c, max6650_id);
static struct i2c_driver max6650_driver = {
.driver = {
.name = "max6650",
},
.probe = max6650_probe,
.remove = max6650_remove,
.id_table = max6650_id,
};
/*
* Client data (each client gets its own)
*/
struct max6650_data {
struct device *hwmon_dev;
struct i2c_client *client;
const struct attribute_group *groups[3];
struct mutex update_lock;
int nr_fans;
char valid; /* zero until following fields are valid */
......@@ -151,6 +126,51 @@ struct max6650_data {
u8 alarm;
};
static const u8 tach_reg[] = {
MAX6650_REG_TACH0,
MAX6650_REG_TACH1,
MAX6650_REG_TACH2,
MAX6650_REG_TACH3,
};
static struct max6650_data *max6650_update_device(struct device *dev)
{
struct max6650_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
int i;
mutex_lock(&data->update_lock);
if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
data->speed = i2c_smbus_read_byte_data(client,
MAX6650_REG_SPEED);
data->config = i2c_smbus_read_byte_data(client,
MAX6650_REG_CONFIG);
for (i = 0; i < data->nr_fans; i++) {
data->tach[i] = i2c_smbus_read_byte_data(client,
tach_reg[i]);
}
data->count = i2c_smbus_read_byte_data(client,
MAX6650_REG_COUNT);
data->dac = i2c_smbus_read_byte_data(client, MAX6650_REG_DAC);
/*
* Alarms are cleared on read in case the condition that
* caused the alarm is removed. Keep the value latched here
* for providing the register through different alarm files.
*/
data->alarm |= i2c_smbus_read_byte_data(client,
MAX6650_REG_ALARM);
data->last_updated = jiffies;
data->valid = 1;
}
mutex_unlock(&data->update_lock);
return data;
}
static ssize_t get_fan(struct device *dev, struct device_attribute *devattr,
char *buf)
{
......@@ -235,8 +255,8 @@ static ssize_t get_target(struct device *dev, struct device_attribute *devattr,
static ssize_t set_target(struct device *dev, struct device_attribute *devattr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct max6650_data *data = i2c_get_clientdata(client);
struct max6650_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
int kscale, ktach;
unsigned long rpm;
int err;
......@@ -304,8 +324,8 @@ static ssize_t get_pwm(struct device *dev, struct device_attribute *devattr,
static ssize_t set_pwm(struct device *dev, struct device_attribute *devattr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct max6650_data *data = i2c_get_clientdata(client);
struct max6650_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
unsigned long pwm;
int err;
......@@ -350,8 +370,8 @@ static ssize_t get_enable(struct device *dev, struct device_attribute *devattr,
static ssize_t set_enable(struct device *dev, struct device_attribute *devattr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct max6650_data *data = i2c_get_clientdata(client);
struct max6650_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
int max6650_modes[3] = {0, 3, 2};
unsigned long mode;
int err;
......@@ -400,8 +420,8 @@ static ssize_t get_div(struct device *dev, struct device_attribute *devattr,
static ssize_t set_div(struct device *dev, struct device_attribute *devattr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct max6650_data *data = i2c_get_clientdata(client);
struct max6650_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
unsigned long div;
int err;
......@@ -446,7 +466,7 @@ static ssize_t get_alarm(struct device *dev, struct device_attribute *devattr,
{
struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
struct max6650_data *data = max6650_update_device(dev);
struct i2c_client *client = to_i2c_client(dev);
struct i2c_client *client = data->client;
int alarm = 0;
if (data->alarm & attr->index) {
......@@ -484,7 +504,8 @@ static umode_t max6650_attrs_visible(struct kobject *kobj, struct attribute *a,
int n)
{
struct device *dev = container_of(kobj, struct device, kobj);
struct i2c_client *client = to_i2c_client(dev);
struct max6650_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
u8 alarm_en = i2c_smbus_read_byte_data(client, MAX6650_REG_ALARM_EN);
struct device_attribute *devattr;
......@@ -519,7 +540,7 @@ static struct attribute *max6650_attrs[] = {
NULL
};
static struct attribute_group max6650_attr_grp = {
static const struct attribute_group max6650_group = {
.attrs = max6650_attrs,
.is_visible = max6650_attrs_visible,
};
......@@ -531,7 +552,7 @@ static struct attribute *max6651_attrs[] = {
NULL
};
static const struct attribute_group max6651_attr_grp = {
static const struct attribute_group max6651_group = {
.attrs = max6651_attrs,
};
......@@ -539,74 +560,17 @@ static const struct attribute_group max6651_attr_grp = {
* Real code
*/
static int max6650_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct max6650_data *data;
int err;
data = devm_kzalloc(&client->dev, sizeof(struct max6650_data),
GFP_KERNEL);
if (!data) {
dev_err(&client->dev, "out of memory.\n");
return -ENOMEM;
}
i2c_set_clientdata(client, data);
mutex_init(&data->update_lock);
data->nr_fans = id->driver_data;
/*
* Initialize the max6650 chip
*/
err = max6650_init_client(client);
if (err)
return err;
err = sysfs_create_group(&client->dev.kobj, &max6650_attr_grp);
if (err)
return err;
/* 3 additional fan inputs for the MAX6651 */
if (data->nr_fans == 4) {
err = sysfs_create_group(&client->dev.kobj, &max6651_attr_grp);
if (err)
goto err_remove;
}
data->hwmon_dev = hwmon_device_register(&client->dev);
if (!IS_ERR(data->hwmon_dev))
return 0;
err = PTR_ERR(data->hwmon_dev);
dev_err(&client->dev, "error registering hwmon device.\n");
if (data->nr_fans == 4)
sysfs_remove_group(&client->dev.kobj, &max6651_attr_grp);
err_remove:
sysfs_remove_group(&client->dev.kobj, &max6650_attr_grp);
return err;
}
static int max6650_remove(struct i2c_client *client)
static int max6650_init_client(struct max6650_data *data,
struct i2c_client *client)
{
struct max6650_data *data = i2c_get_clientdata(client);
hwmon_device_unregister(data->hwmon_dev);
if (data->nr_fans == 4)
sysfs_remove_group(&client->dev.kobj, &max6651_attr_grp);
sysfs_remove_group(&client->dev.kobj, &max6650_attr_grp);
return 0;
}
static int max6650_init_client(struct i2c_client *client)
{
struct max6650_data *data = i2c_get_clientdata(client);
struct device *dev = &client->dev;
int config;
int err = -EIO;
config = i2c_smbus_read_byte_data(client, MAX6650_REG_CONFIG);
if (config < 0) {
dev_err(&client->dev, "Error reading config, aborting.\n");
dev_err(dev, "Error reading config, aborting.\n");
return err;
}
......@@ -620,11 +584,11 @@ static int max6650_init_client(struct i2c_client *client)
config |= MAX6650_CFG_V12;
break;
default:
dev_err(&client->dev, "illegal value for fan_voltage (%d)\n",
dev_err(dev, "illegal value for fan_voltage (%d)\n",
fan_voltage);
}
dev_info(&client->dev, "Fan voltage is set to %dV.\n",
dev_info(dev, "Fan voltage is set to %dV.\n",
(config & MAX6650_CFG_V12) ? 12 : 5);
switch (prescaler) {
......@@ -650,11 +614,10 @@ static int max6650_init_client(struct i2c_client *client)
| MAX6650_CFG_PRESCALER_16;
break;
default:
dev_err(&client->dev, "illegal value for prescaler (%d)\n",
prescaler);
dev_err(dev, "illegal value for prescaler (%d)\n", prescaler);
}
dev_info(&client->dev, "Prescaler is set to %d.\n",
dev_info(dev, "Prescaler is set to %d.\n",
1 << (config & MAX6650_CFG_PRESCALER_MASK));
/*
......@@ -664,17 +627,17 @@ static int max6650_init_client(struct i2c_client *client)
*/
if ((config & MAX6650_CFG_MODE_MASK) == MAX6650_CFG_MODE_OFF) {
dev_dbg(&client->dev, "Change mode to open loop, full off.\n");
dev_dbg(dev, "Change mode to open loop, full off.\n");
config = (config & ~MAX6650_CFG_MODE_MASK)
| MAX6650_CFG_MODE_OPEN_LOOP;
if (i2c_smbus_write_byte_data(client, MAX6650_REG_DAC, 255)) {
dev_err(&client->dev, "DAC write error, aborting.\n");
dev_err(dev, "DAC write error, aborting.\n");
return err;
}
}
if (i2c_smbus_write_byte_data(client, MAX6650_REG_CONFIG, config)) {
dev_err(&client->dev, "Config write error, aborting.\n");
dev_err(dev, "Config write error, aborting.\n");
return err;
}
......@@ -684,51 +647,55 @@ static int max6650_init_client(struct i2c_client *client)
return 0;
}
static const u8 tach_reg[] = {
MAX6650_REG_TACH0,
MAX6650_REG_TACH1,
MAX6650_REG_TACH2,
MAX6650_REG_TACH3,
};
static struct max6650_data *max6650_update_device(struct device *dev)
static int max6650_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
int i;
struct i2c_client *client = to_i2c_client(dev);
struct max6650_data *data = i2c_get_clientdata(client);
mutex_lock(&data->update_lock);
struct device *dev = &client->dev;
struct max6650_data *data;
struct device *hwmon_dev;
int err;
if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
data->speed = i2c_smbus_read_byte_data(client,
MAX6650_REG_SPEED);
data->config = i2c_smbus_read_byte_data(client,
MAX6650_REG_CONFIG);
for (i = 0; i < data->nr_fans; i++) {
data->tach[i] = i2c_smbus_read_byte_data(client,
tach_reg[i]);
}
data->count = i2c_smbus_read_byte_data(client,
MAX6650_REG_COUNT);
data->dac = i2c_smbus_read_byte_data(client, MAX6650_REG_DAC);
data = devm_kzalloc(dev, sizeof(struct max6650_data), GFP_KERNEL);
if (!data)
return -ENOMEM;
/*
* Alarms are cleared on read in case the condition that
* caused the alarm is removed. Keep the value latched here
* for providing the register through different alarm files.
*/
data->alarm |= i2c_smbus_read_byte_data(client,
MAX6650_REG_ALARM);
data->client = client;
mutex_init(&data->update_lock);
data->nr_fans = id->driver_data;
data->last_updated = jiffies;
data->valid = 1;
}
/*
* Initialize the max6650 chip
*/
err = max6650_init_client(data, client);
if (err)
return err;
mutex_unlock(&data->update_lock);
data->groups[0] = &max6650_group;
/* 3 additional fan inputs for the MAX6651 */
if (data->nr_fans == 4)
data->groups[1] = &max6651_group;
return data;
hwmon_dev = devm_hwmon_device_register_with_groups(dev,
client->name, data,
data->groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
}
static const struct i2c_device_id max6650_id[] = {
{ "max6650", 1 },
{ "max6651", 4 },
{ }
};
MODULE_DEVICE_TABLE(i2c, max6650_id);
static struct i2c_driver max6650_driver = {
.driver = {
.name = "max6650",
},
.probe = max6650_probe,
.id_table = max6650_id,
};
module_i2c_driver(max6650_driver);
MODULE_AUTHOR("Hans J. Koch");
......
/*
* Hardware monitoring driver for LTC2974, LTC2977, LTC2978, LTC3880,
* and LTC3883
* LTC3883, and LTM4676
*
* Copyright (c) 2011 Ericsson AB.
* Copyright (c) 2013 Guenter Roeck
* Copyright (c) 2013, 2014 Guenter Roeck
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
......@@ -14,10 +14,6 @@
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/kernel.h>
......@@ -28,7 +24,7 @@
#include <linux/i2c.h>
#include "pmbus.h"
enum chips { ltc2974, ltc2977, ltc2978, ltc3880, ltc3883 };
enum chips { ltc2974, ltc2977, ltc2978, ltc3880, ltc3883, ltm4676 };
/* Common for all chips */
#define LTC2978_MFR_VOUT_PEAK 0xdd
......@@ -45,7 +41,7 @@ enum chips { ltc2974, ltc2977, ltc2978, ltc3880, ltc3883 };
#define LTC2974_MFR_IOUT_PEAK 0xd7
#define LTC2974_MFR_IOUT_MIN 0xd8
/* LTC3880 and LTC3883 */
/* LTC3880, LTC3883, and LTM4676 */
#define LTC3880_MFR_IOUT_PEAK 0xd7
#define LTC3880_MFR_CLEAR_PEAKS 0xe3
#define LTC3880_MFR_TEMPERATURE2_PEAK 0xf4
......@@ -53,7 +49,8 @@ enum chips { ltc2974, ltc2977, ltc2978, ltc3880, ltc3883 };
/* LTC3883 only */
#define LTC3883_MFR_IIN_PEAK 0xe1
#define LTC2974_ID 0x0212
#define LTC2974_ID_REV1 0x0212
#define LTC2974_ID_REV2 0x0213
#define LTC2977_ID 0x0130
#define LTC2978_ID_REV1 0x0121
#define LTC2978_ID_REV2 0x0122
......@@ -62,6 +59,8 @@ enum chips { ltc2974, ltc2977, ltc2978, ltc3880, ltc3883 };
#define LTC3880_ID_MASK 0xff00
#define LTC3883_ID 0x4300
#define LTC3883_ID_MASK 0xff00
#define LTM4676_ID 0x4480 /* datasheet claims 0x440X */
#define LTM4676_ID_MASK 0xfff0
#define LTC2974_NUM_PAGES 4
#define LTC2978_NUM_PAGES 8
......@@ -370,6 +369,7 @@ static const struct i2c_device_id ltc2978_id[] = {
{"ltc2978", ltc2978},
{"ltc3880", ltc3880},
{"ltc3883", ltc3883},
{"ltm4676", ltm4676},
{}
};
MODULE_DEVICE_TABLE(i2c, ltc2978_id);
......@@ -394,7 +394,7 @@ static int ltc2978_probe(struct i2c_client *client,
if (chip_id < 0)
return chip_id;
if (chip_id == LTC2974_ID) {
if (chip_id == LTC2974_ID_REV1 || chip_id == LTC2974_ID_REV2) {
data->id = ltc2974;
} else if (chip_id == LTC2977_ID) {
data->id = ltc2977;
......@@ -405,6 +405,8 @@ static int ltc2978_probe(struct i2c_client *client,
data->id = ltc3880;
} else if ((chip_id & LTC3883_ID_MASK) == LTC3883_ID) {
data->id = ltc3883;
} else if ((chip_id & LTM4676_ID_MASK) == LTM4676_ID) {
data->id = ltm4676;
} else {
dev_err(&client->dev, "Unsupported chip ID 0x%x\n", chip_id);
return -ENODEV;
......@@ -458,6 +460,7 @@ static int ltc2978_probe(struct i2c_client *client,
}
break;
case ltc3880:
case ltm4676:
info->read_word_data = ltc3880_read_word_data;
info->pages = LTC3880_NUM_PAGES;
info->func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_IIN
......@@ -500,5 +503,5 @@ static struct i2c_driver ltc2978_driver = {
module_i2c_driver(ltc2978_driver);
MODULE_AUTHOR("Guenter Roeck");
MODULE_DESCRIPTION("PMBus driver for LTC2974, LTC2978, LTC3880, and LTC3883");
MODULE_DESCRIPTION("PMBus driver for LTC2974, LTC2978, LTC3880, LTC3883, and LTM4676");
MODULE_LICENSE("GPL");
......@@ -222,7 +222,7 @@ static int smm665_read_adc(struct smm665_data *data, int adc)
rv = i2c_smbus_read_word_swapped(client, 0);
if (rv < 0) {
dev_dbg(&client->dev, "Failed to read ADC value: error %d", rv);
return -1;
return rv;
}
/*
* Validate/verify readback adc channel (in bit 11..14).
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment