ASoC: sirf: Add audio usp interface driver

This patch adds ASoC support for SiRF SoCs USP interface.
Features include:
1. Only support slave mode.
2. Support I2S and DSP_A mode.
3. Support S16_LE, S24_LE and S24_3LE formats.
4. Support stereo and mono mode.
5. The biggest Support is 192Khz sample rate.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

sound/soc/sirf/Kconfig

@@ -12,3 +12,9 @@ config SND_SOC_SIRF_AUDIO
 config SND_SOC_SIRF_AUDIO_PORT
 	select REGMAP_MMIO
 	tristate
+
+config SND_SOC_SIRF_USP
+	tristate "SoC Audio (I2S protocol) for SiRF SoC USP interface"
+	depends on SND_SOC_SIRF
+	select REGMAP_MMIO
+	tristate

sound/soc/sirf/Makefile

 snd-soc-sirf-audio-objs := sirf-audio.o
 snd-soc-sirf-audio-port-objs := sirf-audio-port.o
+snd-soc-sirf-usp-objs := sirf-usp.o
 
 obj-$(CONFIG_SND_SOC_SIRF_AUDIO) += snd-soc-sirf-audio.o
 obj-$(CONFIG_SND_SOC_SIRF_AUDIO_PORT) += snd-soc-sirf-audio-port.o
+obj-$(CONFIG_SND_SOC_SIRF_USP) += snd-soc-sirf-usp.o

sound/soc/sirf/sirf-usp.c

+/*
+ * SiRF USP in I2S/DSP mode
+ *
+ * Copyright (c) 2011 Cambridge Silicon Radio Limited, a CSR plc group company.
+ *
+ * Licensed under GPLv2 or later.
+ */
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/clk.h>
+#include <linux/pm_runtime.h>
+#include <sound/soc.h>
+#include <sound/pcm_params.h>
+#include <sound/dmaengine_pcm.h>
+
+#include "sirf-usp.h"
+
+struct sirf_usp {
+	struct regmap *regmap;
+	struct clk *clk;
+	u32 mode1_reg;
+	u32 mode2_reg;
+	int daifmt_format;
+	struct snd_dmaengine_dai_dma_data playback_dma_data;
+	struct snd_dmaengine_dai_dma_data capture_dma_data;
+};
+
+static void sirf_usp_tx_enable(struct sirf_usp *usp)
+{
+	regmap_update_bits(usp->regmap, USP_TX_FIFO_OP,
+		USP_TX_FIFO_RESET, USP_TX_FIFO_RESET);
+	regmap_write(usp->regmap, USP_TX_FIFO_OP, 0);
+
+	regmap_update_bits(usp->regmap, USP_TX_FIFO_OP,
+		USP_TX_FIFO_START, USP_TX_FIFO_START);
+
+	regmap_update_bits(usp->regmap, USP_TX_RX_ENABLE,
+		USP_TX_ENA, USP_TX_ENA);
+}
+
+static void sirf_usp_tx_disable(struct sirf_usp *usp)
+{
+	regmap_update_bits(usp->regmap, USP_TX_RX_ENABLE,
+		USP_TX_ENA, ~USP_TX_ENA);
+	/* FIFO stop */
+	regmap_write(usp->regmap, USP_TX_FIFO_OP, 0);
+}
+
+static void sirf_usp_rx_enable(struct sirf_usp *usp)
+{
+	regmap_update_bits(usp->regmap, USP_RX_FIFO_OP,
+		USP_RX_FIFO_RESET, USP_RX_FIFO_RESET);
+	regmap_write(usp->regmap, USP_RX_FIFO_OP, 0);
+
+	regmap_update_bits(usp->regmap, USP_RX_FIFO_OP,
+		USP_RX_FIFO_START, USP_RX_FIFO_START);
+
+	regmap_update_bits(usp->regmap, USP_TX_RX_ENABLE,
+		USP_RX_ENA, USP_RX_ENA);
+}
+
+static void sirf_usp_rx_disable(struct sirf_usp *usp)
+{
+	regmap_update_bits(usp->regmap, USP_TX_RX_ENABLE,
+		USP_RX_ENA, ~USP_RX_ENA);
+	/* FIFO stop */
+	regmap_write(usp->regmap, USP_RX_FIFO_OP, 0);
+}
+
+static int sirf_usp_pcm_dai_probe(struct snd_soc_dai *dai)
+{
+	struct sirf_usp *usp = snd_soc_dai_get_drvdata(dai);
+	snd_soc_dai_init_dma_data(dai, &usp->playback_dma_data,
+			&usp->capture_dma_data);
+	return 0;
+}
+
+static int sirf_usp_pcm_set_dai_fmt(struct snd_soc_dai *dai,
+		unsigned int fmt)
+{
+	struct sirf_usp *usp = snd_soc_dai_get_drvdata(dai);
+
+	/* set master/slave audio interface */
+	switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
+	case SND_SOC_DAIFMT_CBM_CFM:
+		break;
+	default:
+		dev_err(dai->dev, "Only CBM and CFM supported\n");
+		return -EINVAL;
+	}
+
+	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
+	case SND_SOC_DAIFMT_I2S:
+	case SND_SOC_DAIFMT_DSP_A:
+		usp->daifmt_format = (fmt & SND_SOC_DAIFMT_FORMAT_MASK);
+		break;
+	default:
+		dev_err(dai->dev, "Only I2S and DSP_A format supported\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int sirf_usp_i2s_startup(struct snd_pcm_substream *substream,
+		struct snd_soc_dai *dai)
+{
+	struct sirf_usp *usp = snd_soc_dai_get_drvdata(dai);
+
+	/* Configure RISC mode */
+	regmap_update_bits(usp->regmap, USP_RISC_DSP_MODE,
+		USP_RISC_DSP_SEL, ~USP_RISC_DSP_SEL);
+
+	/*
+	 * Configure DMA IO Length register
+	 * Set no limit, USP can receive data continuously until it is diabled
+	 */
+	regmap_write(usp->regmap, USP_TX_DMA_IO_LEN, 0);
+	regmap_write(usp->regmap, USP_RX_DMA_IO_LEN, 0);
+
+	regmap_write(usp->regmap, USP_RX_FRAME_CTRL, USP_SINGLE_SYNC_MODE);
+
+	regmap_write(usp->regmap, USP_TX_FRAME_CTRL, USP_TXC_SLAVE_CLK_SAMPLE);
+
+	/* Configure Mode2 register */
+	regmap_write(usp->regmap, USP_MODE2, (1 << USP_RXD_DELAY_LEN_OFFSET) |
+		(0 << USP_TXD_DELAY_LEN_OFFSET));
+
+	/* Configure Mode1 register */
+	regmap_write(usp->regmap, USP_MODE1,
+		USP_SYNC_MODE | USP_EN | USP_TXD_ACT_EDGE_FALLING |
+		USP_RFS_ACT_LEVEL_LOGIC1 | USP_TFS_ACT_LEVEL_LOGIC1 |
+		USP_TX_UFLOW_REPEAT_ZERO);
+
+	/* Configure RX DMA IO Control register */
+	regmap_write(usp->regmap, USP_RX_DMA_IO_CTRL, 0);
+
+	/* Congiure RX FIFO Control register */
+	regmap_write(usp->regmap, USP_RX_FIFO_CTRL,
+		(USP_RX_FIFO_THRESHOLD << USP_RX_FIFO_THD_OFFSET) |
+		(USP_TX_RX_FIFO_WIDTH_DWORD << USP_RX_FIFO_WIDTH_OFFSET));
+
+	/* Congiure RX FIFO Level Check register */
+	regmap_write(usp->regmap, USP_RX_FIFO_LEVEL_CHK,
+		RX_FIFO_SC(0x04) | RX_FIFO_LC(0x0E) | RX_FIFO_HC(0x1B));
+
+	/* Configure TX DMA IO Control register*/
+	regmap_write(usp->regmap, USP_TX_DMA_IO_CTRL, 0);
+
+	/* Configure TX FIFO Control register */
+	regmap_write(usp->regmap, USP_TX_FIFO_CTRL,
+		(USP_TX_FIFO_THRESHOLD << USP_TX_FIFO_THD_OFFSET) |
+		(USP_TX_RX_FIFO_WIDTH_DWORD << USP_TX_FIFO_WIDTH_OFFSET));
+	/* Congiure TX FIFO Level Check register */
+	regmap_write(usp->regmap, USP_TX_FIFO_LEVEL_CHK,
+		TX_FIFO_SC(0x1B) | TX_FIFO_LC(0x0E) | TX_FIFO_HC(0x04));
+
+	return 0;
+}
+
+static int sirf_usp_pcm_hw_params(struct snd_pcm_substream *substream,
+		struct snd_pcm_hw_params *params, struct snd_soc_dai *dai)
+{
+	struct sirf_usp *usp = snd_soc_dai_get_drvdata(dai);
+	u32 data_len, frame_len, shifter_len;
+
+	switch (params_format(params)) {
+	case SNDRV_PCM_FORMAT_S16_LE:
+		data_len = 16;
+		frame_len = 16;
+		break;
+	case SNDRV_PCM_FORMAT_S24_LE:
+		data_len = 24;
+		frame_len = 32;
+		break;
+	case SNDRV_PCM_FORMAT_S24_3LE:
+		data_len = 24;
+		frame_len = 24;
+		break;
+	default:
+		dev_err(dai->dev, "Format unsupported\n");
+		return -EINVAL;
+	}
+
+	shifter_len = data_len;
+
+	switch (usp->daifmt_format) {
+	case SND_SOC_DAIFMT_I2S:
+		regmap_update_bits(usp->regmap, USP_RX_FRAME_CTRL,
+			USP_I2S_SYNC_CHG, USP_I2S_SYNC_CHG);
+		break;
+	case SND_SOC_DAIFMT_DSP_A:
+		regmap_update_bits(usp->regmap, USP_RX_FRAME_CTRL,
+			USP_I2S_SYNC_CHG, 0);
+		frame_len = data_len * params_channels(params);
+		data_len = frame_len;
+		break;
+	default:
+		dev_err(dai->dev, "Only support I2S and DSP_A mode\n");
+		return -EINVAL;
+	}
+
+	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
+		regmap_update_bits(usp->regmap, USP_TX_FRAME_CTRL,
+			USP_TXC_DATA_LEN_MASK | USP_TXC_FRAME_LEN_MASK
+			| USP_TXC_SHIFTER_LEN_MASK,
+			((data_len - 1) << USP_TXC_DATA_LEN_OFFSET)
+			| ((frame_len - 1) << USP_TXC_FRAME_LEN_OFFSET)
+			| ((shifter_len - 1) << USP_TXC_SHIFTER_LEN_OFFSET));
+	else
+		regmap_update_bits(usp->regmap, USP_RX_FRAME_CTRL,
+			USP_RXC_DATA_LEN_MASK | USP_RXC_FRAME_LEN_MASK
+			| USP_RXC_SHIFTER_LEN_MASK,
+			((data_len - 1) << USP_RXC_DATA_LEN_OFFSET)
+			| ((frame_len - 1) << USP_RXC_FRAME_LEN_OFFSET)
+			| ((shifter_len - 1) << USP_RXC_SHIFTER_LEN_OFFSET));
+
+	regmap_update_bits(usp->regmap, USP_MODE1,
+			USP_CLOCK_MODE_SLAVE, USP_CLOCK_MODE_SLAVE);
+	regmap_update_bits(usp->regmap, USP_MODE2,
+			USP_TFS_CLK_SLAVE_MODE | USP_RFS_CLK_SLAVE_MODE,
+			USP_TFS_CLK_SLAVE_MODE | USP_RFS_CLK_SLAVE_MODE);
+
+	return 0;
+}
+
+static int sirf_usp_pcm_trigger(struct snd_pcm_substream *substream, int cmd,
+				struct snd_soc_dai *dai)
+{
+	struct sirf_usp *usp = snd_soc_dai_get_drvdata(dai);
+
+	switch (cmd) {
+	case SNDRV_PCM_TRIGGER_START:
+	case SNDRV_PCM_TRIGGER_RESUME:
+	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
+		if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
+			sirf_usp_tx_enable(usp);
+		else
+			sirf_usp_rx_enable(usp);
+		break;
+	case SNDRV_PCM_TRIGGER_STOP:
+	case SNDRV_PCM_TRIGGER_SUSPEND:
+	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
+		if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
+			sirf_usp_tx_disable(usp);
+		else
+			sirf_usp_rx_disable(usp);
+		break;
+	}
+
+	return 0;
+}
+
+static const struct snd_soc_dai_ops sirf_usp_pcm_dai_ops = {
+	.startup = sirf_usp_i2s_startup,
+	.trigger = sirf_usp_pcm_trigger,
+	.set_fmt = sirf_usp_pcm_set_dai_fmt,
+	.hw_params = sirf_usp_pcm_hw_params,
+};
+
+static struct snd_soc_dai_driver sirf_usp_pcm_dai = {
+	.probe = sirf_usp_pcm_dai_probe,
+	.name = "sirf-usp-pcm",
+	.id = 0,
+	.playback = {
+		.stream_name = "SiRF USP PCM Playback",
+		.channels_min = 1,
+		.channels_max = 2,
+		.rates = SNDRV_PCM_RATE_8000_192000,
+		.formats = SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE |
+			SNDRV_PCM_FMTBIT_S24_3LE,
+	},
+	.capture = {
+		.stream_name = "SiRF USP PCM Capture",
+		.channels_min = 1,
+		.channels_max = 2,
+		.rates = SNDRV_PCM_RATE_8000_192000,
+		.formats = SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE |
+			SNDRV_PCM_FMTBIT_S24_3LE,
+	},
+	.ops = &sirf_usp_pcm_dai_ops,
+};
+
+#ifdef CONFIG_PM_RUNTIME
+static int sirf_usp_pcm_runtime_suspend(struct device *dev)
+{
+	struct sirf_usp *usp = dev_get_drvdata(dev);
+	clk_disable_unprepare(usp->clk);
+	return 0;
+}
+
+static int sirf_usp_pcm_runtime_resume(struct device *dev)
+{
+	struct sirf_usp *usp = dev_get_drvdata(dev);
+	return clk_prepare_enable(usp->clk);
+}
+#endif
+
+#ifdef CONFIG_PM_SLEEP
+static int sirf_usp_pcm_suspend(struct device *dev)
+{
+	struct sirf_usp *usp = dev_get_drvdata(dev);
+
+	if (!pm_runtime_status_suspended(dev)) {
+		regmap_read(usp->regmap, USP_MODE1, &usp->mode1_reg);
+		regmap_read(usp->regmap, USP_MODE2, &usp->mode2_reg);
+		sirf_usp_pcm_runtime_suspend(dev);
+	}
+	return 0;
+}
+
+static int sirf_usp_pcm_resume(struct device *dev)
+{
+	struct sirf_usp *usp = dev_get_drvdata(dev);
+	int ret;
+
+	if (!pm_runtime_status_suspended(dev)) {
+		ret = sirf_usp_pcm_runtime_resume(dev);
+		if (ret)
+			return ret;
+		regmap_write(usp->regmap, USP_MODE1, usp->mode1_reg);
+		regmap_write(usp->regmap, USP_MODE2, usp->mode2_reg);
+	}
+	return 0;
+}
+#endif
+
+static const struct snd_soc_component_driver sirf_usp_component = {
+	.name		= "sirf-usp",
+};
+
+static const struct regmap_config sirf_usp_regmap_config = {
+	.reg_bits = 32,
+	.reg_stride = 4,
+	.val_bits = 32,
+	.max_register = USP_RX_FIFO_DATA,
+	.cache_type = REGCACHE_NONE,
+};
+
+static int sirf_usp_pcm_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct sirf_usp *usp;
+	void __iomem *base;
+	struct resource *mem_res;
+
+	usp = devm_kzalloc(&pdev->dev, sizeof(struct sirf_usp),
+			GFP_KERNEL);
+	if (!usp)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, usp);
+
+	mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap(&pdev->dev, mem_res->start,
+		resource_size(mem_res));
+	if (base == NULL)
+		return -ENOMEM;
+	usp->regmap = devm_regmap_init_mmio(&pdev->dev, base,
+					    &sirf_usp_regmap_config);
+	if (IS_ERR(usp->regmap))
+		return PTR_ERR(usp->regmap);
+
+	usp->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(usp->clk)) {
+		dev_err(&pdev->dev, "Get clock failed.\n");
+		return PTR_ERR(usp->clk);
+	}
+
+	pm_runtime_enable(&pdev->dev);
+
+	ret = devm_snd_soc_register_component(&pdev->dev, &sirf_usp_component,
+		&sirf_usp_pcm_dai, 1);
+	if (ret) {
+		dev_err(&pdev->dev, "Register Audio SoC dai failed.\n");
+		return ret;
+	}
+	return devm_snd_dmaengine_pcm_register(&pdev->dev, NULL, 0);
+}
+
+static int sirf_usp_pcm_remove(struct platform_device *pdev)
+{
+	pm_runtime_disable(&pdev->dev);
+	return 0;
+}
+
+static const struct of_device_id sirf_usp_pcm_of_match[] = {
+	{ .compatible = "sirf,prima2-usp-pcm", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, sirf_usp_pcm_of_match);
+
+static const struct dev_pm_ops sirf_usp_pcm_pm_ops = {
+	SET_RUNTIME_PM_OPS(sirf_usp_pcm_runtime_suspend,
+		sirf_usp_pcm_runtime_resume, NULL)
+	SET_SYSTEM_SLEEP_PM_OPS(sirf_usp_pcm_suspend, sirf_usp_pcm_resume)
+};
+
+static struct platform_driver sirf_usp_pcm_driver = {
+	.driver = {
+		.name = "sirf-usp-pcm",
+		.owner = THIS_MODULE,
+		.of_match_table = sirf_usp_pcm_of_match,
+		.pm = &sirf_usp_pcm_pm_ops,
+	},
+	.probe = sirf_usp_pcm_probe,
+	.remove = sirf_usp_pcm_remove,
+};
+
+module_platform_driver(sirf_usp_pcm_driver);
+
+MODULE_DESCRIPTION("SiRF SoC USP PCM bus driver");
+MODULE_AUTHOR("RongJun Ying <Rongjun.Ying@csr.com>");
+MODULE_LICENSE("GPL v2");

sound/soc/sirf/sirf-usp.h

+/*
+ * arch/arm/mach-prima2/include/mach/sirfsoc_usp.h
+ *
+ * Copyright (c) 2011 Cambridge Silicon Radio Limited, a CSR plc group company.
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#ifndef _SIRF_USP_H
+#define _SIRF_USP_H
+
+/* USP Registers */
+#define USP_MODE1		0x00
+#define USP_MODE2		0x04
+#define USP_TX_FRAME_CTRL	0x08
+#define USP_RX_FRAME_CTRL	0x0C
+#define USP_TX_RX_ENABLE	0x10
+#define USP_INT_ENABLE		0x14
+#define USP_INT_STATUS		0x18
+#define USP_PIN_IO_DATA		0x1C
+#define USP_RISC_DSP_MODE	0x20
+#define USP_AYSNC_PARAM_REG	0x24
+#define USP_IRDA_X_MODE_DIV	0x28
+#define USP_SM_CFG		0x2C
+#define USP_TX_DMA_IO_CTRL	0x100
+#define USP_TX_DMA_IO_LEN	0x104
+#define USP_TX_FIFO_CTRL	0x108
+#define USP_TX_FIFO_LEVEL_CHK	0x10C
+#define USP_TX_FIFO_OP		0x110
+#define USP_TX_FIFO_STATUS	0x114
+#define USP_TX_FIFO_DATA	0x118
+#define USP_RX_DMA_IO_CTRL	0x120
+#define USP_RX_DMA_IO_LEN	0x124
+#define USP_RX_FIFO_CTRL	0x128
+#define USP_RX_FIFO_LEVEL_CHK	0x12C
+#define USP_RX_FIFO_OP		0x130
+#define USP_RX_FIFO_STATUS	0x134
+#define USP_RX_FIFO_DATA	0x138
+
+/* USP MODE register-1 */
+#define USP_SYNC_MODE			0x00000001
+#define USP_CLOCK_MODE_SLAVE		0x00000002
+#define USP_LOOP_BACK_EN		0x00000004
+#define USP_HPSIR_EN			0x00000008
+#define USP_ENDIAN_CTRL_LSBF		0x00000010
+#define USP_EN				0x00000020
+#define USP_RXD_ACT_EDGE_FALLING	0x00000040
+#define USP_TXD_ACT_EDGE_FALLING	0x00000080
+#define USP_RFS_ACT_LEVEL_LOGIC1	0x00000100
+#define USP_TFS_ACT_LEVEL_LOGIC1	0x00000200
+#define USP_SCLK_IDLE_MODE_TOGGLE	0x00000400
+#define USP_SCLK_IDLE_LEVEL_LOGIC1	0x00000800
+#define USP_SCLK_PIN_MODE_IO	0x00001000
+#define USP_RFS_PIN_MODE_IO	0x00002000
+#define USP_TFS_PIN_MODE_IO	0x00004000
+#define USP_RXD_PIN_MODE_IO	0x00008000
+#define USP_TXD_PIN_MODE_IO	0x00010000
+#define USP_SCLK_IO_MODE_INPUT	0x00020000
+#define USP_RFS_IO_MODE_INPUT	0x00040000
+#define USP_TFS_IO_MODE_INPUT	0x00080000
+#define USP_RXD_IO_MODE_INPUT	0x00100000
+#define USP_TXD_IO_MODE_INPUT	0x00200000
+#define USP_IRDA_WIDTH_DIV_MASK	0x3FC00000
+#define USP_IRDA_WIDTH_DIV_OFFSET	0
+#define USP_IRDA_IDLE_LEVEL_HIGH	0x40000000
+#define USP_TX_UFLOW_REPEAT_ZERO	0x80000000
+#define USP_TX_ENDIAN_MODE		0x00000020
+#define USP_RX_ENDIAN_MODE		0x00000020
+
+/* USP Mode Register-2 */
+#define USP_RXD_DELAY_LEN_MASK		0x000000FF
+#define USP_RXD_DELAY_LEN_OFFSET	0
+
+#define USP_TXD_DELAY_LEN_MASK		0x0000FF00
+#define USP_TXD_DELAY_LEN_OFFSET	8
+
+#define USP_ENA_CTRL_MODE		0x00010000
+#define USP_FRAME_CTRL_MODE		0x00020000
+#define USP_TFS_SOURCE_MODE             0x00040000
+#define USP_TFS_MS_MODE                 0x00080000
+#define USP_CLK_DIVISOR_MASK		0x7FE00000
+#define USP_CLK_DIVISOR_OFFSET		21
+
+#define USP_TFS_CLK_SLAVE_MODE		(1<<20)
+#define USP_RFS_CLK_SLAVE_MODE		(1<<19)
+
+#define USP_IRDA_DATA_WIDTH		0x80000000
+
+/* USP Transmit Frame Control Register */
+
+#define USP_TXC_DATA_LEN_MASK		0x000000FF
+#define USP_TXC_DATA_LEN_OFFSET		0
+
+#define USP_TXC_SYNC_LEN_MASK		0x0000FF00
+#define USP_TXC_SYNC_LEN_OFFSET		8
+
+#define USP_TXC_FRAME_LEN_MASK		0x00FF0000
+#define USP_TXC_FRAME_LEN_OFFSET	16
+
+#define USP_TXC_SHIFTER_LEN_MASK	0x1F000000
+#define USP_TXC_SHIFTER_LEN_OFFSET	24
+
+#define USP_TXC_SLAVE_CLK_SAMPLE	0x20000000
+
+#define USP_TXC_CLK_DIVISOR_MASK	0xC0000000
+#define USP_TXC_CLK_DIVISOR_OFFSET	30
+
+/* USP Receive Frame Control Register */
+
+#define USP_RXC_DATA_LEN_MASK		0x000000FF
+#define USP_RXC_DATA_LEN_OFFSET		0
+
+#define USP_RXC_FRAME_LEN_MASK		0x0000FF00
+#define USP_RXC_FRAME_LEN_OFFSET	8
+
+#define USP_RXC_SHIFTER_LEN_MASK	0x001F0000
+#define USP_RXC_SHIFTER_LEN_OFFSET	16
+
+#define USP_START_EDGE_MODE	0x00800000
+#define USP_I2S_SYNC_CHG	0x00200000
+
+#define USP_RXC_CLK_DIVISOR_MASK	0x0F000000
+#define USP_RXC_CLK_DIVISOR_OFFSET	24
+#define USP_SINGLE_SYNC_MODE		0x00400000
+
+/* Tx - RX Enable Register */
+
+#define USP_RX_ENA		0x00000001
+#define USP_TX_ENA		0x00000002
+
+/* USP Interrupt Enable and status Register */
+#define USP_RX_DONE_INT			0x00000001
+#define USP_TX_DONE_INT			0x00000002
+#define USP_RX_OFLOW_INT		0x00000004
+#define USP_TX_UFLOW_INT		0x00000008
+#define USP_RX_IO_DMA_INT		0x00000010
+#define USP_TX_IO_DMA_INT		0x00000020
+#define USP_RXFIFO_FULL_INT		0x00000040
+#define USP_TXFIFO_EMPTY_INT		0x00000080
+#define USP_RXFIFO_THD_INT		0x00000100
+#define USP_TXFIFO_THD_INT		0x00000200
+#define USP_UART_FRM_ERR_INT		0x00000400
+#define USP_RX_TIMEOUT_INT		0x00000800
+#define USP_TX_ALLOUT_INT		0x00001000
+#define USP_RXD_BREAK_INT		0x00008000
+
+/* All possible TX interruots */
+#define USP_TX_INTERRUPT		(USP_TX_DONE_INT|USP_TX_UFLOW_INT|\
+					USP_TX_IO_DMA_INT|\
+					USP_TXFIFO_EMPTY_INT|\
+					USP_TXFIFO_THD_INT)
+/* All possible RX interruots */
+#define USP_RX_INTERRUPT		(USP_RX_DONE_INT|USP_RX_OFLOW_INT|\
+					USP_RX_IO_DMA_INT|\
+					USP_RXFIFO_FULL_INT|\
+					USP_RXFIFO_THD_INT|\
+					USP_RXFIFO_THD_INT|USP_RX_TIMEOUT_INT)
+
+#define USP_INT_ALL        0x1FFF
+
+/* USP Pin I/O Data Register */
+
+#define USP_RFS_PIN_VALUE_MASK	0x00000001
+#define USP_TFS_PIN_VALUE_MASK	0x00000002
+#define USP_RXD_PIN_VALUE_MASK	0x00000004
+#define USP_TXD_PIN_VALUE_MASK	0x00000008
+#define USP_SCLK_PIN_VALUE_MASK	0x00000010
+
+/* USP RISC/DSP Mode Register */
+#define USP_RISC_DSP_SEL	0x00000001
+
+/* USP ASYNC PARAMETER Register*/
+
+#define USP_ASYNC_TIMEOUT_MASK	0x0000FFFF
+#define USP_ASYNC_TIMEOUT_OFFSET	0
+#define USP_ASYNC_TIMEOUT(x)	(((x)&USP_ASYNC_TIMEOUT_MASK) \
+				<<USP_ASYNC_TIMEOUT_OFFSET)
+
+#define USP_ASYNC_DIV2_MASK		0x003F0000
+#define USP_ASYNC_DIV2_OFFSET		16
+
+/* USP TX DMA I/O MODE Register */
+#define USP_TX_MODE_IO			0x00000001
+
+/* USP TX DMA I/O Length Register */
+#define USP_TX_DATA_LEN_MASK		0xFFFFFFFF
+#define USP_TX_DATA_LEN_OFFSET		0
+
+/* USP TX FIFO Control Register */
+#define USP_TX_FIFO_WIDTH_MASK		0x00000003
+#define USP_TX_FIFO_WIDTH_OFFSET	0
+
+#define USP_TX_FIFO_THD_MASK		0x000001FC
+#define USP_TX_FIFO_THD_OFFSET		2
+
+/* USP TX FIFO Level Check Register */
+#define USP_TX_FIFO_LEVEL_CHECK_MASK	0x1F
+#define USP_TX_FIFO_SC_OFFSET	0
+#define USP_TX_FIFO_LC_OFFSET	10
+#define USP_TX_FIFO_HC_OFFSET	20
+
+#define TX_FIFO_SC(x)		(((x) & USP_TX_FIFO_LEVEL_CHECK_MASK) \
+				<< USP_TX_FIFO_SC_OFFSET)
+#define TX_FIFO_LC(x)		(((x) & USP_TX_FIFO_LEVEL_CHECK_MASK) \
+				<< USP_TX_FIFO_LC_OFFSET)
+#define TX_FIFO_HC(x)		(((x) & USP_TX_FIFO_LEVEL_CHECK_MASK) \
+				<< USP_TX_FIFO_HC_OFFSET)
+
+/* USP TX FIFO Operation Register */
+#define USP_TX_FIFO_RESET		0x00000001
+#define USP_TX_FIFO_START		0x00000002
+
+/* USP TX FIFO Status Register */
+#define USP_TX_FIFO_LEVEL_MASK		0x0000007F
+#define USP_TX_FIFO_LEVEL_OFFSET	0
+
+#define USP_TX_FIFO_FULL		0x00000080
+#define USP_TX_FIFO_EMPTY		0x00000100
+
+/* USP TX FIFO Data Register */
+#define USP_TX_FIFO_DATA_MASK		0xFFFFFFFF
+#define USP_TX_FIFO_DATA_OFFSET		0
+
+/* USP RX DMA I/O MODE Register */
+#define USP_RX_MODE_IO			0x00000001
+#define USP_RX_DMA_FLUSH		0x00000004
+
+/* USP RX DMA I/O Length Register */
+#define USP_RX_DATA_LEN_MASK		0xFFFFFFFF
+#define USP_RX_DATA_LEN_OFFSET		0
+
+/* USP RX FIFO Control Register */
+#define USP_RX_FIFO_WIDTH_MASK		0x00000003
+#define USP_RX_FIFO_WIDTH_OFFSET	0
+
+#define USP_RX_FIFO_THD_MASK		0x000001FC
+#define USP_RX_FIFO_THD_OFFSET		2
+
+/* USP RX FIFO Level Check Register */
+
+#define USP_RX_FIFO_LEVEL_CHECK_MASK	0x1F
+#define USP_RX_FIFO_SC_OFFSET	0
+#define USP_RX_FIFO_LC_OFFSET	10
+#define USP_RX_FIFO_HC_OFFSET	20
+
+#define RX_FIFO_SC(x)		(((x) & USP_RX_FIFO_LEVEL_CHECK_MASK) \
+				<< USP_RX_FIFO_SC_OFFSET)
+#define RX_FIFO_LC(x)		(((x) & USP_RX_FIFO_LEVEL_CHECK_MASK) \
+				<< USP_RX_FIFO_LC_OFFSET)
+#define RX_FIFO_HC(x)		(((x) & USP_RX_FIFO_LEVEL_CHECK_MASK) \
+				<< USP_RX_FIFO_HC_OFFSET)
+
+/* USP RX FIFO Operation Register */
+#define USP_RX_FIFO_RESET		0x00000001
+#define USP_RX_FIFO_START		0x00000002
+
+/* USP RX FIFO Status Register */
+
+#define USP_RX_FIFO_LEVEL_MASK		0x0000007F
+#define USP_RX_FIFO_LEVEL_OFFSET	0
+
+#define USP_RX_FIFO_FULL		0x00000080
+#define USP_RX_FIFO_EMPTY		0x00000100
+
+/* USP RX FIFO Data Register */
+
+#define USP_RX_FIFO_DATA_MASK		0xFFFFFFFF
+#define USP_RX_FIFO_DATA_OFFSET		0
+
+/*
+ * When rx thd irq occur, sender just disable tx empty irq,
+ * Remaining data in tx fifo wil also be sent out.
+ */
+#define USP_FIFO_SIZE			128
+#define USP_TX_FIFO_THRESHOLD		(USP_FIFO_SIZE/2)
+#define USP_RX_FIFO_THRESHOLD		(USP_FIFO_SIZE/2)
+
+/* FIFO_WIDTH for the USP_TX_FIFO_CTRL and USP_RX_FIFO_CTRL registers */
+#define USP_FIFO_WIDTH_BYTE  0x00
+#define USP_FIFO_WIDTH_WORD  0x01
+#define USP_FIFO_WIDTH_DWORD 0x02
+
+#define USP_ASYNC_DIV2          16
+
+#define USP_PLUGOUT_RETRY_CNT	2
+
+#define USP_TX_RX_FIFO_WIDTH_DWORD    2
+
+#define SIRF_USP_DIV_MCLK	0
+
+#define SIRF_USP_I2S_TFS_SYNC	0
+#define SIRF_USP_I2S_RFS_SYNC	1
+#endif