Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits)
  [ARM] Update mach-types
  ARM: 5636/1: Move vendor enum to AMBA include
  ARM: Fix pfn_valid() for sparse memory
  [ARM] orion5x: Add LaCie NAS 2Big Network support
  [ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume
  ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
  ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
  ARM: 5689/1: Update default config of HP Jornada 700-series machines
  ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem
  ARM: 5688/1: ks8695_serial: disable_irq() lockup
  ARM: 5687/1: fix an oops with highmem
  ARM: 5684/1: Add nuc960 platform to w90x900
  ARM: 5683/1: Add nuc950 platform to w90x900
  ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform
  ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver
  ARM: 5625/1: fix hard coded 4K resource size in amba bus detection
  MMC: MMCI: convert realview MMC to use gpiolib
  ARM: 5685/1: Make MMCI driver compile without gpiolib
  ARM: implement highpte
  ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ
  ...

Fix up trivial conflict in arch/arm/kernel/signal.c.

It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83 ("KEYS:
Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.

Documentation/arm/Samsung-S3C24XX/CPUfreq.txt

+		S3C24XX CPUfreq support
+		=======================
+
+Introduction
+------------
+
+ The S3C24XX series support a number of power saving systems, such as
+ the ability to change the core, memory and peripheral operating
+ frequencies. The core control is exported via the CPUFreq driver
+ which has a number of different manual or automatic controls over the
+ rate the core is running at.
+
+ There are two forms of the driver depending on the specific CPU and
+ how the clocks are arranged. The first implementation used as single
+ PLL to feed the ARM, memory and peripherals via a series of dividers
+ and muxes and this is the implementation that is documented here. A
+ newer version where there is a seperate PLL and clock divider for the
+ ARM core is available as a seperate driver.
+
+
+Layout
+------
+
+ The code core manages the CPU specific drivers, any data that they
+ need to register and the interface to the generic drivers/cpufreq
+ system. Each CPU registers a driver to control the PLL, clock dividers
+ and anything else associated with it. Any board that wants to use this
+ framework needs to supply at least basic details of what is required.
+
+ The core registers with drivers/cpufreq at init time if all the data
+ necessary has been supplied.
+
+
+CPU support
+-----------
+
+ The support for each CPU depends on the facilities provided by the
+ SoC and the driver as each device has different PLL and clock chains
+ associated with it.
+
+
+Slow Mode
+---------
+
+ The SLOW mode where the PLL is turned off altogether and the
+ system is fed by the external crystal input is currently not
+ supported.
+
+
+sysfs
+-----
+
+ The core code exports extra information via sysfs in the directory
+ devices/system/cpu/cpu0/arch-freq.
+
+
+Board Support
+-------------
+
+ Each board that wants to use the cpufreq code must register some basic
+ information with the core driver to provide information about what the
+ board requires and any restrictions being placed on it.
+
+ The board needs to supply information about whether it needs the IO bank
+ timings changing, any maximum frequency limits and information about the
+ SDRAM refresh rate.
+
+
+
+
+Document Author
+---------------
+
+Ben Dooks, Copyright 2009 Simtec Electronics
+Licensed under GPLv2

MAINTAINERS

@@ -534,10 +534,30 @@ L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 W:	http://maxim.org.za/at91_26.html
 S:	Maintained
 
+ARM/BCMRING ARM ARCHITECTURE
+M:	Leo Chen <leochen@broadcom.com>
+M:	Scott Branden <sbranden@broadcom.com>
+L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
+S:	Maintained
+F:	arch/arm/mach-bcmring
+
+ARM/BCMRING MTD NAND DRIVER
+M:	Leo Chen <leochen@broadcom.com>
+M:	Scott Branden <sbranden@broadcom.com>
+L:	linux-mtd@lists.infradead.org
+S:	Maintained
+F:	drivers/mtd/nand/bcm_umi_nand.c
+F:	drivers/mtd/nand/bcm_umi_bch.c
+F:	drivers/mtd/nand/bcm_umi_hamming.c
+F:	drivers/mtd/nand/nand_bcm_umi.h
+
 ARM/CIRRUS LOGIC EP93XX ARM ARCHITECTURE
-M:	Lennert Buytenhek <kernel@wantstofly.org>
+M:	Hartley Sweeten <hsweeten@visionengravers.com>
+M:	Ryan Mallon <ryan@bluewatersys.com>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
+F:	arch/arm/mach-ep93xx/
+F:	arch/arm/mach-ep93xx/include/mach/
 
 ARM/CIRRUS LOGIC EDB9315A MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
@@ -685,6 +705,18 @@ ARM/MAGICIAN MACHINE SUPPORT
 M:	Philipp Zabel <philipp.zabel@gmail.com>
 S:	Maintained
 
+ARM/Marvell Loki/Kirkwood/MV78xx0/Orion SOC support
+M:	Lennert Buytenhek <buytenh@marvell.com>
+M:	Nicolas Pitre <nico@marvell.com>
+L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
+T:	git git://git.marvell.com/orion
+S:	Maintained
+F:	arch/arm/mach-loki/
+F:	arch/arm/mach-kirkwood/
+F:	arch/arm/mach-mv78xx0/
+F:	arch/arm/mach-orion5x/
+F:	arch/arm/plat-orion/
+
 ARM/MIOA701 MACHINE SUPPORT
 M:	Robert Jarzmik <robert.jarzmik@free.fr>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)

arch/arm/Kconfig.debug

@@ -8,6 +8,7 @@ source "lib/Kconfig.debug"
 # n, but then RMK will have to kill you ;).
 config FRAME_POINTER
 	bool
+	depends on !THUMB2_KERNEL
 	default y if !ARM_UNWIND
 	help
 	  If you say N here, the resulting kernel will be slightly smaller and

arch/arm/Makefile

@@ -93,9 +93,16 @@ ifeq ($(CONFIG_ARM_UNWIND),y)
 CFLAGS_ABI	+=-funwind-tables
 endif
 
+ifeq ($(CONFIG_THUMB2_KERNEL),y)
+AFLAGS_AUTOIT	:=$(call as-option,-Wa$(comma)-mimplicit-it=thumb,-Wa$(comma)-mauto-it)
+AFLAGS_NOWARN	:=$(call as-option,-Wa$(comma)-mno-warn-deprecated,-Wa$(comma)-W)
+CFLAGS_THUMB2	:=-mthumb $(AFLAGS_AUTOIT) $(AFLAGS_NOWARN)
+AFLAGS_THUMB2	:=$(CFLAGS_THUMB2) -Wa$(comma)-mthumb
+endif
+
 # Need -Uarm for gcc < 3.x
-KBUILD_CFLAGS	+=$(CFLAGS_ABI) $(arch-y) $(tune-y) $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) -msoft-float -Uarm
-KBUILD_AFLAGS	+=$(CFLAGS_ABI) $(arch-y) $(tune-y) -msoft-float
+KBUILD_CFLAGS	+=$(CFLAGS_ABI) $(CFLAGS_THUMB2) $(arch-y) $(tune-y) $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) -msoft-float -Uarm
+KBUILD_AFLAGS	+=$(CFLAGS_ABI) $(AFLAGS_THUMB2) $(arch-y) $(tune-y) -include asm/unified.h -msoft-float
 
 CHECKFLAGS	+= -D__arm__
 
@@ -112,6 +119,7 @@ endif
 # by CONFIG_* macro name.
 machine-$(CONFIG_ARCH_AAEC2000)		:= aaec2000
 machine-$(CONFIG_ARCH_AT91)		:= at91
+machine-$(CONFIG_ARCH_BCMRING)		:= bcmring
 machine-$(CONFIG_ARCH_CLPS711X)		:= clps711x
 machine-$(CONFIG_ARCH_DAVINCI)		:= davinci
 machine-$(CONFIG_ARCH_EBSA110)		:= ebsa110
@@ -135,8 +143,10 @@ machine-$(CONFIG_ARCH_MSM)		:= msm
 machine-$(CONFIG_ARCH_MV78XX0)		:= mv78xx0
 machine-$(CONFIG_ARCH_MX1)		:= mx1
 machine-$(CONFIG_ARCH_MX2)		:= mx2
+machine-$(CONFIG_ARCH_MX25)		:= mx25
 machine-$(CONFIG_ARCH_MX3)		:= mx3
 machine-$(CONFIG_ARCH_NETX)		:= netx
+machine-$(CONFIG_ARCH_NOMADIK)		:= nomadik
 machine-$(CONFIG_ARCH_NS9XXX)		:= ns9xxx
 machine-$(CONFIG_ARCH_OMAP1)		:= omap1
 machine-$(CONFIG_ARCH_OMAP2)		:= omap2
@@ -150,6 +160,7 @@ machine-$(CONFIG_ARCH_RPC)		:= rpc
 machine-$(CONFIG_ARCH_S3C2410)		:= s3c2410 s3c2400 s3c2412 s3c2440 s3c2442 s3c2443
 machine-$(CONFIG_ARCH_S3C24A0)		:= s3c24a0
 machine-$(CONFIG_ARCH_S3C64XX)		:= s3c6400 s3c6410
+machine-$(CONFIG_ARCH_S5PC1XX)		:= s5pc100
 machine-$(CONFIG_ARCH_SA1100)		:= sa1100
 machine-$(CONFIG_ARCH_SHARK)		:= shark
 machine-$(CONFIG_ARCH_STMP378X)		:= stmp378x
@@ -158,6 +169,7 @@ machine-$(CONFIG_ARCH_U300)		:= u300
 machine-$(CONFIG_ARCH_VERSATILE)	:= versatile
 machine-$(CONFIG_ARCH_W90X900)		:= w90x900
 machine-$(CONFIG_FOOTBRIDGE)		:= footbridge
+machine-$(CONFIG_ARCH_MXC91231)		:= mxc91231
 
 # Platform directory name.  This list is sorted alphanumerically
 # by CONFIG_* macro name.
@@ -168,6 +180,7 @@ plat-$(CONFIG_PLAT_ORION)	:= orion
 plat-$(CONFIG_PLAT_PXA)		:= pxa
 plat-$(CONFIG_PLAT_S3C24XX)	:= s3c24xx s3c
 plat-$(CONFIG_PLAT_S3C64XX)	:= s3c64xx s3c
+plat-$(CONFIG_PLAT_S5PC1XX)	:= s5pc1xx s3c
 plat-$(CONFIG_ARCH_STMP3XXX)	:= stmp3xxx
 
 ifeq ($(CONFIG_ARCH_EBSA110),y)

arch/arm/boot/Makefile

@@ -61,7 +61,7 @@ endif
 
 quiet_cmd_uimage = UIMAGE  $@
       cmd_uimage = $(CONFIG_SHELL) $(MKIMAGE) -A arm -O linux -T kernel \
-		   -C none -a $(LOADADDR) -e $(LOADADDR) \
+		   -C none -a $(LOADADDR) -e $(STARTADDR) \
 		   -n 'Linux-$(KERNELRELEASE)' -d $< $@
 
 ifeq ($(CONFIG_ZBOOT_ROM),y)
@@ -70,6 +70,13 @@ else
 $(obj)/uImage: LOADADDR=$(ZRELADDR)
 endif
 
+ifeq ($(CONFIG_THUMB2_KERNEL),y)
+# Set bit 0 to 1 so that "mov pc, rx" switches to Thumb-2 mode
+$(obj)/uImage: STARTADDR=$(shell echo $(LOADADDR) | sed -e "s/.$$/1/")
+else
+$(obj)/uImage: STARTADDR=$(LOADADDR)
+endif
+
 $(obj)/uImage:	$(obj)/zImage FORCE
 	$(call if_changed,uimage)
 	@echo '  Image $@ is ready'

arch/arm/common/vic.c

@@ -22,10 +22,20 @@
 #include <linux/list.h>
 #include <linux/io.h>
 #include <linux/sysdev.h>
+#include <linux/amba/bus.h>
 
 #include <asm/mach/irq.h>
 #include <asm/hardware/vic.h>
 
+static void vic_ack_irq(unsigned int irq)
+{
+	void __iomem *base = get_irq_chip_data(irq);
+	irq &= 31;
+	writel(1 << irq, base + VIC_INT_ENABLE_CLEAR);
+	/* moreover, clear the soft-triggered, in case it was the reason */
+	writel(1 << irq, base + VIC_INT_SOFT_CLEAR);
+}
+
 static void vic_mask_irq(unsigned int irq)
 {
 	void __iomem *base = get_irq_chip_data(irq);
@@ -253,12 +263,16 @@ static inline void vic_pm_register(void __iomem *base, unsigned int irq, u32 arg
 
 static struct irq_chip vic_chip = {
 	.name	= "VIC",
-	.ack	= vic_mask_irq,
+	.ack	= vic_ack_irq,
 	.mask	= vic_mask_irq,
 	.unmask	= vic_unmask_irq,
 	.set_wake = vic_set_wake,
 };
 
+/* The PL190 cell from ARM has been modified by ST, so handle both here */
+static void vik_init_st(void __iomem *base, unsigned int irq_start,
+			 u32 vic_sources);
+
 /**
  * vic_init - initialise a vectored interrupt controller
  * @base: iomem base address
@@ -270,6 +284,28 @@ void __init vic_init(void __iomem *base, unsigned int irq_start,
 		     u32 vic_sources, u32 resume_sources)
 {
 	unsigned int i;
+	u32 cellid = 0;
+	enum amba_vendor vendor;
+
+	/* Identify which VIC cell this one is, by reading the ID */
+	for (i = 0; i < 4; i++) {
+		u32 addr = ((u32)base & PAGE_MASK) + 0xfe0 + (i * 4);
+		cellid |= (readl(addr) & 0xff) << (8 * i);
+	}
+	vendor = (cellid >> 12) & 0xff;
+	printk(KERN_INFO "VIC @%p: id 0x%08x, vendor 0x%02x\n",
+	       base, cellid, vendor);
+
+	switch(vendor) {
+	case AMBA_VENDOR_ST:
+		vik_init_st(base, irq_start, vic_sources);
+		return;
+	default:
+		printk(KERN_WARNING "VIC: unknown vendor, continuing anyways\n");
+		/* fall through */
+	case AMBA_VENDOR_ARM:
+		break;
+	}
 
 	/* Disable all interrupts initially. */
 
@@ -306,3 +342,60 @@ void __init vic_init(void __iomem *base, unsigned int irq_start,
 
 	vic_pm_register(base, irq_start, resume_sources);
 }
+
+/*
+ * The PL190 cell from ARM has been modified by ST to handle 64 interrupts.
+ * The original cell has 32 interrupts, while the modified one has 64,
+ * replocating two blocks 0x00..0x1f in 0x20..0x3f. In that case
+ * the probe function is called twice, with base set to offset 000
+ *  and 020 within the page. We call this "second block".
+ */
+static void __init vik_init_st(void __iomem *base, unsigned int irq_start,
+				u32 vic_sources)
+{
+	unsigned int i;
+	int vic_2nd_block = ((unsigned long)base & ~PAGE_MASK) != 0;
+
+	/* Disable all interrupts initially. */
+
+	writel(0, base + VIC_INT_SELECT);
+	writel(0, base + VIC_INT_ENABLE);
+	writel(~0, base + VIC_INT_ENABLE_CLEAR);
+	writel(0, base + VIC_IRQ_STATUS);
+	writel(0, base + VIC_ITCR);
+	writel(~0, base + VIC_INT_SOFT_CLEAR);
+
+	/*
+	 * Make sure we clear all existing interrupts. The vector registers
+	 * in this cell are after the second block of general registers,
+	 * so we can address them using standard offsets, but only from
+	 * the second base address, which is 0x20 in the page
+	 */
+	if (vic_2nd_block) {
+		writel(0, base + VIC_PL190_VECT_ADDR);
+		for (i = 0; i < 19; i++) {
+			unsigned int value;
+
+			value = readl(base + VIC_PL190_VECT_ADDR);
+			writel(value, base + VIC_PL190_VECT_ADDR);
+		}
+		/* ST has 16 vectors as well, but we don't enable them by now */
+		for (i = 0; i < 16; i++) {
+			void __iomem *reg = base + VIC_VECT_CNTL0 + (i * 4);
+			writel(0, reg);
+		}
+
+		writel(32, base + VIC_PL190_DEF_VECT_ADDR);
+	}
+
+	for (i = 0; i < 32; i++) {
+		if (vic_sources & (1 << i)) {
+			unsigned int irq = irq_start + i;
+
+			set_irq_chip(irq, &vic_chip);
+			set_irq_chip_data(irq, base);
+			set_irq_handler(irq, handle_level_irq);
+			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+		}
+	}
+}

arch/arm/include/asm/assembler.h

@@ -74,23 +74,56 @@
  * Enable and disable interrupts
  */
 #if __LINUX_ARM_ARCH__ >= 6
-	.macro	disable_irq
+	.macro	disable_irq_notrace
 	cpsid	i
 	.endm
 
-	.macro	enable_irq
+	.macro	enable_irq_notrace
 	cpsie	i
 	.endm
 #else
-	.macro	disable_irq
+	.macro	disable_irq_notrace
 	msr	cpsr_c, #PSR_I_BIT | SVC_MODE
 	.endm
 
-	.macro	enable_irq
+	.macro	enable_irq_notrace
 	msr	cpsr_c, #SVC_MODE
 	.endm
 #endif
 
+	.macro asm_trace_hardirqs_off
+#if defined(CONFIG_TRACE_IRQFLAGS)
+	stmdb   sp!, {r0-r3, ip, lr}
+	bl	trace_hardirqs_off
+	ldmia	sp!, {r0-r3, ip, lr}
+#endif
+	.endm
+
+	.macro asm_trace_hardirqs_on_cond, cond
+#if defined(CONFIG_TRACE_IRQFLAGS)
+	/*
+	 * actually the registers should be pushed and pop'd conditionally, but
+	 * after bl the flags are certainly clobbered
+	 */
+	stmdb   sp!, {r0-r3, ip, lr}
+	bl\cond	trace_hardirqs_on
+	ldmia	sp!, {r0-r3, ip, lr}
+#endif
+	.endm
+
+	.macro asm_trace_hardirqs_on
+	asm_trace_hardirqs_on_cond al
+	.endm
+
+	.macro disable_irq
+	disable_irq_notrace
+	asm_trace_hardirqs_off
+	.endm
+
+	.macro enable_irq
+	asm_trace_hardirqs_on
+	enable_irq_notrace
+	.endm
 /*
  * Save the current IRQ state and disable IRQs.  Note that this macro
  * assumes FIQs are enabled, and that the processor is in SVC mode.
@@ -104,10 +137,16 @@
  * Restore interrupt state previously stored in a register.  We don't
  * guarantee that this will preserve the flags.
  */
-	.macro	restore_irqs, oldcpsr
+	.macro	restore_irqs_notrace, oldcpsr
 	msr	cpsr_c, \oldcpsr
 	.endm
 
+	.macro restore_irqs, oldcpsr
+	tst	\oldcpsr, #PSR_I_BIT
+	asm_trace_hardirqs_on_cond eq
+	restore_irqs_notrace \oldcpsr
+	.endm
+
 #define USER(x...)				\
 9999:	x;					\
 	.section __ex_table,"a";		\
@@ -127,3 +166,87 @@
 #endif
 #endif
 	.endm
+
+#ifdef CONFIG_THUMB2_KERNEL
+	.macro	setmode, mode, reg
+	mov	\reg, #\mode
+	msr	cpsr_c, \reg
+	.endm
+#else
+	.macro	setmode, mode, reg
+	msr	cpsr_c, #\mode
+	.endm
+#endif
+
+/*
+ * STRT/LDRT access macros with ARM and Thumb-2 variants
+ */
+#ifdef CONFIG_THUMB2_KERNEL
+
+	.macro	usraccoff, instr, reg, ptr, inc, off, cond, abort
+9999:
+	.if	\inc == 1
+	\instr\cond\()bt \reg, [\ptr, #\off]
+	.elseif	\inc == 4
+	\instr\cond\()t \reg, [\ptr, #\off]
+	.else
+	.error	"Unsupported inc macro argument"
+	.endif
+
+	.section __ex_table,"a"
+	.align	3
+	.long	9999b, \abort
+	.previous
+	.endm
+
+	.macro	usracc, instr, reg, ptr, inc, cond, rept, abort
+	@ explicit IT instruction needed because of the label
+	@ introduced by the USER macro
+	.ifnc	\cond,al
+	.if	\rept == 1
+	itt	\cond
+	.elseif	\rept == 2
+	ittt	\cond
+	.else
+	.error	"Unsupported rept macro argument"
+	.endif
+	.endif
+
+	@ Slightly optimised to avoid incrementing the pointer twice
+	usraccoff \instr, \reg, \ptr, \inc, 0, \cond, \abort
+	.if	\rept == 2
+	usraccoff \instr, \reg, \ptr, \inc, 4, \cond, \abort
+	.endif
+
+	add\cond \ptr, #\rept * \inc
+	.endm
+
+#else	/* !CONFIG_THUMB2_KERNEL */
+
+	.macro	usracc, instr, reg, ptr, inc, cond, rept, abort
+	.rept	\rept
+9999:
+	.if	\inc == 1
+	\instr\cond\()bt \reg, [\ptr], #\inc
+	.elseif	\inc == 4
+	\instr\cond\()t \reg, [\ptr], #\inc
+	.else
+	.error	"Unsupported inc macro argument"
+	.endif
+
+	.section __ex_table,"a"
+	.align	3
+	.long	9999b, \abort
+	.previous
+	.endr
+	.endm
+
+#endif	/* CONFIG_THUMB2_KERNEL */
+
+	.macro	strusr, reg, ptr, inc, cond=al, rept=1, abort=9001f
+	usracc	str, \reg, \ptr, \inc, \cond, \rept, \abort
+	.endm
+
+	.macro	ldrusr, reg, ptr, inc, cond=al, rept=1, abort=9001f
+	usracc	ldr, \reg, \ptr, \inc, \cond, \rept, \abort
+	.endm

arch/arm/include/asm/elf.h

@@ -55,6 +55,9 @@ typedef struct user_fp elf_fpregset_t;
 #define R_ARM_MOVW_ABS_NC	43
 #define R_ARM_MOVT_ABS		44
 
+#define R_ARM_THM_CALL		10
+#define R_ARM_THM_JUMP24	30
+
 /*
  * These are used to set parameters in the core dumps.
  */

arch/arm/include/asm/ftrace.h

@@ -7,8 +7,43 @@
 
 #ifndef __ASSEMBLY__
 extern void mcount(void);
+extern void __gnu_mcount_nc(void);
 #endif
 
 #endif
 
+#ifndef __ASSEMBLY__
+
+#if defined(CONFIG_FRAME_POINTER) && !defined(CONFIG_ARM_UNWIND)
+/*
+ * return_address uses walk_stackframe to do it's work.  If both
+ * CONFIG_FRAME_POINTER=y and CONFIG_ARM_UNWIND=y walk_stackframe uses unwind
+ * information.  For this to work in the function tracer many functions would
+ * have to be marked with __notrace.  So for now just depend on
+ * !CONFIG_ARM_UNWIND.
+ */
+
+void *return_address(unsigned int);
+
+#else
+
+extern inline void *return_address(unsigned int level)
+{
+	return NULL;
+}
+
+#endif
+
+#define HAVE_ARCH_CALLER_ADDR
+
+#define CALLER_ADDR0 ((unsigned long)__builtin_return_address(0))
+#define CALLER_ADDR1 ((unsigned long)return_address(1))
+#define CALLER_ADDR2 ((unsigned long)return_address(2))
+#define CALLER_ADDR3 ((unsigned long)return_address(3))
+#define CALLER_ADDR4 ((unsigned long)return_address(4))
+#define CALLER_ADDR5 ((unsigned long)return_address(5))
+#define CALLER_ADDR6 ((unsigned long)return_address(6))
+
+#endif /* ifndef __ASSEMBLY__ */
+
 #endif /* _ASM_ARM_FTRACE */

arch/arm/include/asm/futex.h

@@ -99,6 +99,7 @@ futex_atomic_cmpxchg_inatomic(int __user *uaddr, int oldval, int newval)
 	__asm__ __volatile__("@futex_atomic_cmpxchg_inatomic\n"
 	"1:	ldrt	%0, [%3]\n"
 	"	teq	%0, %1\n"
+	"	it	eq	@ explicit IT needed for the 2b label\n"
 	"2:	streqt	%2, [%3]\n"
 	"3:\n"
 	"	.section __ex_table,\"a\"\n"

arch/arm/include/asm/mach/mmc.h

@@ -10,6 +10,8 @@ struct mmc_platform_data {
 	unsigned int ocr_mask;			/* available voltages */
 	u32 (*translate_vdd)(struct device *, unsigned int);
 	unsigned int (*status)(struct device *);
+	int	gpio_wp;
+	int	gpio_cd;
 };
 
 #endif

arch/arm/include/asm/memory.h

@@ -44,7 +44,13 @@
  * The module space lives between the addresses given by TASK_SIZE
  * and PAGE_OFFSET - it must be within 32MB of the kernel text.
  */
+#ifndef CONFIG_THUMB2_KERNEL
 #define MODULES_VADDR		(PAGE_OFFSET - 16*1024*1024)
+#else
+/* smaller range for Thumb-2 symbols relocation (2^24)*/
+#define MODULES_VADDR		(PAGE_OFFSET - 8*1024*1024)
+#endif
+
 #if TASK_SIZE > MODULES_VADDR
 #error Top of user space clashes with start of module space
 #endif
@@ -212,7 +218,6 @@ static inline __deprecated void *bus_to_virt(unsigned long x)
  *
  *  page_to_pfn(page)	convert a struct page * to a PFN number
  *  pfn_to_page(pfn)	convert a _valid_ PFN number to struct page *
- *  pfn_valid(pfn)	indicates whether a PFN number is valid
  *
  *  virt_to_page(k)	convert a _valid_ virtual address to struct page *
  *  virt_addr_valid(k)	indicates whether a virtual address is valid
@@ -221,10 +226,6 @@ static inline __deprecated void *bus_to_virt(unsigned long x)
 
 #define ARCH_PFN_OFFSET		PHYS_PFN_OFFSET
 
-#ifndef CONFIG_SPARSEMEM
-#define pfn_valid(pfn)		((pfn) >= PHYS_PFN_OFFSET && (pfn) < (PHYS_PFN_OFFSET + max_mapnr))
-#endif
-
 #define virt_to_page(kaddr)	pfn_to_page(__pa(kaddr) >> PAGE_SHIFT)
 #define virt_addr_valid(kaddr)	((unsigned long)(kaddr) >= PAGE_OFFSET && (unsigned long)(kaddr) < (unsigned long)high_memory)
 
@@ -241,18 +242,6 @@ static inline __deprecated void *bus_to_virt(unsigned long x)
 #define arch_pfn_to_nid(pfn)	PFN_TO_NID(pfn)
 #define arch_local_page_offset(pfn, nid) LOCAL_MAP_NR((pfn) << PAGE_SHIFT)
 
-#define pfn_valid(pfn)						\
-	({							\
-		unsigned int nid = PFN_TO_NID(pfn);		\
-		int valid = nid < MAX_NUMNODES;			\
-		if (valid) {					\
-			pg_data_t *node = NODE_DATA(nid);	\
-			valid = (pfn - node->node_start_pfn) <	\
-				node->node_spanned_pages;	\
-		}						\
-		valid;						\
-	})
-
 #define virt_to_page(kaddr)					\
 	(ADDR_TO_MAPBASE(kaddr) + LOCAL_MAP_NR(kaddr))
 

arch/arm/include/asm/mmu_context.h

@@ -62,8 +62,10 @@ static inline void check_context(struct mm_struct *mm)
 
 static inline void check_context(struct mm_struct *mm)
 {
+#ifdef CONFIG_MMU
 	if (unlikely(mm->context.kvm_seq != init_mm.context.kvm_seq))
 		__check_kvm_seq(mm);
+#endif
 }
 
 #define init_new_context(tsk,mm)	0

arch/arm/include/asm/page-nommu.h

@@ -43,7 +43,4 @@ typedef unsigned long pgprot_t;
 #define __pmd(x)        (x)
 #define __pgprot(x)     (x)
 
-extern unsigned long memory_start;
-extern unsigned long memory_end;
-
 #endif

arch/arm/include/asm/page.h

@@ -194,6 +194,10 @@ typedef unsigned long pgprot_t;
 
 typedef struct page *pgtable_t;
 
+#ifndef CONFIG_SPARSEMEM
+extern int pfn_valid(unsigned long);
+#endif
+
 #include <asm/memory.h>
 
 #endif /* !__ASSEMBLY__ */

arch/arm/include/asm/pgalloc.h

@@ -36,6 +36,8 @@ extern void free_pgd_slow(struct mm_struct *mm, pgd_t *pgd);
 #define pgd_alloc(mm)			get_pgd_slow(mm)
 #define pgd_free(mm, pgd)		free_pgd_slow(mm, pgd)
 
+#define PGALLOC_GFP	(GFP_KERNEL | __GFP_NOTRACK | __GFP_REPEAT | __GFP_ZERO)
+
 /*
  * Allocate one PTE table.
  *
@@ -57,7 +59,7 @@ pte_alloc_one_kernel(struct mm_struct *mm, unsigned long addr)
 {
 	pte_t *pte;
 
-	pte = (pte_t *)__get_free_page(GFP_KERNEL|__GFP_REPEAT|__GFP_ZERO);
+	pte = (pte_t *)__get_free_page(PGALLOC_GFP);
 	if (pte) {
 		clean_dcache_area(pte, sizeof(pte_t) * PTRS_PER_PTE);
 		pte += PTRS_PER_PTE;
@@ -71,10 +73,16 @@ pte_alloc_one(struct mm_struct *mm, unsigned long addr)
 {
 	struct page *pte;
 
-	pte = alloc_pages(GFP_KERNEL|__GFP_REPEAT|__GFP_ZERO, 0);
+#ifdef CONFIG_HIGHPTE
+	pte = alloc_pages(PGALLOC_GFP | __GFP_HIGHMEM, 0);
+#else
+	pte = alloc_pages(PGALLOC_GFP, 0);
+#endif
 	if (pte) {
+		if (!PageHighMem(pte)) {
 			void *page = page_address(pte);
 			clean_dcache_area(page, sizeof(pte_t) * PTRS_PER_PTE);
+		}
 		pgtable_page_ctor(pte);
 	}
 

arch/arm/include/asm/pgtable.h

@@ -162,10 +162,8 @@ extern void __pgd_error(const char *file, int line, unsigned long val);
  * entries are stored 1024 bytes below.
  */
 #define L_PTE_PRESENT		(1 << 0)
-#define L_PTE_FILE		(1 << 1)	/* only when !PRESENT */
 #define L_PTE_YOUNG		(1 << 1)
-#define L_PTE_BUFFERABLE	(1 << 2)	/* obsolete, matches PTE */
-#define L_PTE_CACHEABLE		(1 << 3)	/* obsolete, matches PTE */
+#define L_PTE_FILE		(1 << 2)	/* only when !PRESENT */
 #define L_PTE_DIRTY		(1 << 6)
 #define L_PTE_WRITE		(1 << 7)
 #define L_PTE_USER		(1 << 8)
@@ -264,10 +262,19 @@ extern struct page *empty_zero_page;
 #define pte_clear(mm,addr,ptep)	set_pte_ext(ptep, __pte(0), 0)
 #define pte_page(pte)		(pfn_to_page(pte_pfn(pte)))
 #define pte_offset_kernel(dir,addr)	(pmd_page_vaddr(*(dir)) + __pte_index(addr))
-#define pte_offset_map(dir,addr)	(pmd_page_vaddr(*(dir)) + __pte_index(addr))
-#define pte_offset_map_nested(dir,addr)	(pmd_page_vaddr(*(dir)) + __pte_index(addr))
-#define pte_unmap(pte)		do { } while (0)
-#define pte_unmap_nested(pte)	do { } while (0)
+
+#define pte_offset_map(dir,addr)	(__pte_map(dir, KM_PTE0) + __pte_index(addr))
+#define pte_offset_map_nested(dir,addr)	(__pte_map(dir, KM_PTE1) + __pte_index(addr))
+#define pte_unmap(pte)			__pte_unmap(pte, KM_PTE0)
+#define pte_unmap_nested(pte)		__pte_unmap(pte, KM_PTE1)
+
+#ifndef CONFIG_HIGHPTE
+#define __pte_map(dir,km)	pmd_page_vaddr(*(dir))
+#define __pte_unmap(pte,km)	do { } while (0)
+#else
+#define __pte_map(dir,km)	((pte_t *)kmap_atomic(pmd_page(*(dir)), km) + PTRS_PER_PTE)
+#define __pte_unmap(pte,km)	kunmap_atomic((pte - PTRS_PER_PTE), km)
+#endif
 
 #define set_pte_ext(ptep,pte,ext) cpu_set_pte_ext(ptep,pte,ext)
 
@@ -381,13 +388,13 @@ extern pgd_t swapper_pg_dir[PTRS_PER_PGD];
  *
  *   3 3 2 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1
  *   1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0
- *   <--------------- offset --------------------> <--- type --> 0 0
+ *   <--------------- offset --------------------> <- type --> 0 0 0
  *
- * This gives us up to 127 swap files and 32GB per swap file.  Note that
+ * This gives us up to 63 swap files and 32GB per swap file.  Note that
  * the offset field is always non-zero.
  */
-#define __SWP_TYPE_SHIFT	2
-#define __SWP_TYPE_BITS		7
+#define __SWP_TYPE_SHIFT	3
+#define __SWP_TYPE_BITS		6
 #define __SWP_TYPE_MASK		((1 << __SWP_TYPE_BITS) - 1)
 #define __SWP_OFFSET_SHIFT	(__SWP_TYPE_BITS + __SWP_TYPE_SHIFT)
 
@@ -411,13 +418,13 @@ extern pgd_t swapper_pg_dir[PTRS_PER_PGD];
  *
  *   3 3 2 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1
  *   1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0
- *   <------------------------ offset -------------------------> 1 0
+ *   <----------------------- offset ------------------------> 1 0 0
  */
 #define pte_file(pte)		(pte_val(pte) & L_PTE_FILE)
-#define pte_to_pgoff(x)		(pte_val(x) >> 2)
-#define pgoff_to_pte(x)		__pte(((x) << 2) | L_PTE_FILE)
+#define pte_to_pgoff(x)		(pte_val(x) >> 3)
+#define pgoff_to_pte(x)		__pte(((x) << 3) | L_PTE_FILE)
 
-#define PTE_FILE_MAX_BITS	30
+#define PTE_FILE_MAX_BITS	29
 
 /* Needs to be defined here and not in linux/mm.h, as it is arch dependent */
 /* FIXME: this is not correct */

arch/arm/include/asm/ptrace.h

@@ -82,6 +82,14 @@
 #define PSR_ENDSTATE	0
 #endif
 
+/* 
+ * These are 'magic' values for PTRACE_PEEKUSR that return info about where a
+ * process is located in memory.
+ */
+#define PT_TEXT_ADDR		0x10000
+#define PT_DATA_ADDR		0x10004
+#define PT_TEXT_END_ADDR	0x10008
+
 #ifndef __ASSEMBLY__
 
 /*

arch/arm/include/asm/thread_info.h

@@ -142,6 +142,7 @@ extern void vfp_sync_state(struct thread_info *thread);
 #define TIF_USING_IWMMXT	17
 #define TIF_MEMDIE		18
 #define TIF_FREEZE		19
+#define TIF_RESTORE_SIGMASK	20
 
 #define _TIF_SIGPENDING		(1 << TIF_SIGPENDING)
 #define _TIF_NEED_RESCHED	(1 << TIF_NEED_RESCHED)
@@ -150,6 +151,7 @@ extern void vfp_sync_state(struct thread_info *thread);
 #define _TIF_POLLING_NRFLAG	(1 << TIF_POLLING_NRFLAG)
 #define _TIF_USING_IWMMXT	(1 << TIF_USING_IWMMXT)
 #define _TIF_FREEZE		(1 << TIF_FREEZE)
+#define _TIF_RESTORE_SIGMASK	(1 << TIF_RESTORE_SIGMASK)
 
 /*
  * Change these and you break ASM code in entry-common.S

arch/arm/kernel/armksyms.c

@@ -186,4 +186,5 @@ EXPORT_SYMBOL(_find_next_bit_be);
 
 #ifdef CONFIG_FUNCTION_TRACER
 EXPORT_SYMBOL(mcount);
+EXPORT_SYMBOL(__gnu_mcount_nc);
 #endif