Merge tag 'qcom-arm64-for-5.6' of...

Merge tag 'qcom-arm64-for-5.6' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt

Qualcomm ARM64 DT updates for v5.6

* Align SDM845 firmware paths with linux-firmware
* Make WiFi work on Dragonboard845c
* Wire up wakeup controller for SDM845
* Critical thermal interrupt support for SDM845, MSM8996 and MSM8998
* Enable UFS for SM8150
* Add remoteproc enablers and nodes for SM8150
* Add CPUfreq for SM8150
* Add RPMH power-domain node for SM8150
* Cleanup and refactor MSM8996 dts structure
* Add initial Inforce Computing IFC6640 dts
* Increase MSM8996 core voltage
* Fix MSM8996 USB phy settings
* Add missing alias for BLSP UART in MSM8998 MTP
* Add remoteproc nodes for ADSP, modem and sensor core for MSM8998
* Enable WiFI for MSM8998
* Introduce the SC7180 platform and the IDP development board
* Add CPUfreq, QUPs, USB, remoteproc etc for SC7180
* Enable USB OTG for Dragonboard 410c
* Add vibrator motor node for PM8916
* Properly specify APCS clocks for MSM8916
* Add CPR and HFPLL for QCS404
* Enable full CPUfreq (with AVS) for QCS404

* tag 'qcom-arm64-for-5.6' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (88 commits)
  arm64: dts: qcom: sdm845: move gpu zap nodes to per-device dts
  arm64: dts: qcom: sm8150: Hard code rpmhpd constants
  arm64: dts: apq8096-db820c: Fix VDD core voltage
  arm64: dts: qcom: qcs404-evb: Set vdd_apc regulator in high power mode
  arm64: dts: qcom: msm8998-mtp: Add alias for blsp1_uart3
  arm64: dts: qcom: sc7180: Add critical interrupt and cooling maps for TSENS in SC7180
  arm64: dts: qcom: msm8996: Fix venus iommu nodename error
  arm64: dts: qcom: sdm845: add the ufs reset
  arm64: dts: qcom: sm8150: Fix UFS phy register size
  arm64: dts: qcom: sm8150-mtp: Add UFS gpio reset
  arm64: dts: qcom: qcs404: Add CPR and populate OPP table
  arm64: dts: qcom: qcs404: Add DVFS support
  arm64: dts: qcom: qcs404: Add the clocks for APCS mux/divider
  arm64: dts: qcom: qcs404: Add HFPLL node
  arm64: dts: qcom: msm8916: Add the clocks for the APCS mux/divider
  arm64: dts: qcom: sc7180: Add rpmh power-domain node
  arm64: dts: pm8004: Add SPMI regulator and add phandles to lsids
  arm64: dts: msm8998: thermal: Add critical interrupt support
  arm64: dts: msm8996: thermal: Add critical interrupt support
  arm64: dts: qcom: db845c: Move remoteproc firmware to sdm845
  ...

Link: https://lore.kernel.org/r/20200113204225.GB3325@yogaSigned-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/arm/qcom.yaml

@@ -28,24 +28,26 @@ description: |
         apq8074
         apq8084
         apq8096
+        ipq8074
+        mdm9615
         msm8916
         msm8974
         msm8992
         msm8994
         msm8996
-  	mdm9615
-  	ipq8074
+        sc7180
         sdm845
 
   The 'board' element must be one of the following strings:
 
         cdp
-  	liquid
         dragonboard
-  	mtp
-  	sbc
         hk01
+        idp
+        liquid
+        mtp
         qrd
+        sbc
 
   The 'soc_version' and 'board_version' elements take the form of v<Major>.<Minor>
   where the minor number may be omitted when it's zero, i.e.  v1.0 is the same
@@ -144,4 +146,8 @@ properties:
               - qcom,ipq8074-hk01
           - const: qcom,ipq8074
 
+      - items:
+          - enum:
+              - qcom,sc7180-idp
+          - const: qcom,sc7180
 ...

arch/arm64/boot/dts/qcom/Makefile

 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8016-sbc.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-db820c.dtb
+dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk01.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-longcheer-l8150.dtb
@@ -13,6 +14,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-asus-novago-tp370ql.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-hp-envy-x2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-lenovo-miix-630.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r3.dtb

arch/arm64/boot/dts/qcom/apq8016-sbc-pmic-pins.dtsi

@@ -5,6 +5,15 @@
 &pm8916_gpios {
 
 	usb_hub_reset_pm: usb_hub_reset_pm {
+		pinconf {
+			pins = "gpio3";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			input-disable;
+			output-high;
+		};
+	};
+
+	usb_hub_reset_pm_device: usb_hub_reset_pm_device {
 		pinconf {
 			pins = "gpio3";
 			function = PMIC_GPIO_FUNC_NORMAL;
@@ -22,6 +31,16 @@ pinconf {
 		};
 	};
 
+	usb_sw_sel_pm_device: usb_sw_sel_pm_device {
+		pinconf {
+			pins = "gpio4";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			power-source = <PM8916_GPIO_VPH>;
+			input-disable;
+			output-low;
+		};
+	};
+
 	pm8916_gpios_leds: pm8916_gpios_leds {
 		pinconf {
 			pins = "gpio1", "gpio2";

arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi

@@ -358,14 +358,15 @@ sdhci@7864000 {
 		};
 
 		usb@78d9000 {
-			extcon = <&usb_id>;
+			extcon = <&usb_id>, <&usb_id>;
 			status = "okay";
 			adp-disable;
 			hnp-disable;
 			srp-disable;
-			dr_mode = "host";
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb_sw_sel_pm>;
+			dr_mode = "otg";
+			pinctrl-names = "default", "device";
+			pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
+			pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
 			ulpi {
 				phy {
 					v1p8-supply = <&pm8916_l7>;
@@ -504,7 +505,7 @@ usb2513 {
 
 	usb_id: usb-id {
 		compatible = "linux,extcon-usb-gpio";
-		vbus-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>;
+		id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&usb_id_default>;
 	};

arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi

-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
- */
-&msmgpio {
-	sdc2_cd_on: sdc2_cd_on {
-		mux {
-			pins = "gpio38";
-			function = "gpio";
-		};
-
-		config {
-			pins = "gpio38";
-			bias-pull-up;		/* pull up */
-			drive-strength = <16>;	/* 16 MA */
-		};
-	};
-
-	sdc2_cd_off: sdc2_cd_off {
-		mux {
-			pins = "gpio38";
-			function = "gpio";
-		};
-
-		config {
-			pins = "gpio38";
-			bias-pull-up;		/* pull up */
-			drive-strength = <2>;	/* 2 MA */
-		};
-	};
-
-	blsp1_uart1_default: blsp1_uart1_default {
-		mux {
-			pins = "gpio41", "gpio42", "gpio43", "gpio44";
-			function = "blsp_uart2";
-		};
-
-		config {
-			pins = "gpio41", "gpio42", "gpio43", "gpio44";
-			drive-strength = <16>;
-			bias-disable;
-		};
-	};
-
-	blsp1_uart1_sleep: blsp1_uart1_sleep {
-		mux {
-			pins = "gpio41", "gpio42", "gpio43", "gpio44";
-			function = "gpio";
-		};
-
-		config {
-			pins = "gpio41", "gpio42", "gpio43", "gpio44";
-			drive-strength = <2>;
-			bias-disable;
-		};
-	};
-
-	hdmi_hpd_active: hdmi_hpd_active {
-		mux {
-			pins = "gpio34";
-			function = "hdmi_hot";
-		};
-
-		config {
-			pins = "gpio34";
-			bias-pull-down;
-			drive-strength = <16>;
-		};
-	};
-
-	hdmi_hpd_suspend: hdmi_hpd_suspend {
-		mux {
-			pins = "gpio34";
-			function = "hdmi_hot";
-		};
-
-		config {
-			pins = "gpio34";
-			bias-pull-down;
-			drive-strength = <2>;
-		};
-	};
-
-	hdmi_ddc_active: hdmi_ddc_active {
-		mux {
-			pins = "gpio32", "gpio33";
-			function = "hdmi_ddc";
-		};
-
-		config {
-			pins = "gpio32", "gpio33";
-			drive-strength = <2>;
-			bias-pull-up;
-		};
-	};
-
-	hdmi_ddc_suspend: hdmi_ddc_suspend {
-		mux {
-			pins = "gpio32", "gpio33";
-			function = "hdmi_ddc";
-		};
-
-		config {
-			pins = "gpio32", "gpio33";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
-	};
-};

arch/arm64/boot/dts/qcom/apq8096-db820c-pmic-pins.dtsi

-// SPDX-License-Identifier: GPL-2.0
-
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-&pm8994_gpios {
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&ls_exp_gpio_f &bt_en_gpios>;
-
-	ls_exp_gpio_f: pm8994_gpio5 {
-		pinconf {
-			pins = "gpio5";
-			output-low;
-			power-source = <2>; // PM8994_GPIO_S4, 1.8V
-		};
-	};
-
-	bt_en_gpios: bt_en_gpios {
-		pinconf {
-			pins = "gpio19";
-			function = PMIC_GPIO_FUNC_NORMAL;
-			output-low;
-			power-source = <PM8994_GPIO_S4>; // 1.8V
-			qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
-			bias-pull-down;
-		};
-	};
-
-	wlan_en_gpios: wlan_en_gpios {
-		pinconf {
-			pins = "gpio8";
-			function = PMIC_GPIO_FUNC_NORMAL;
-			output-low;
-			power-source = <PM8994_GPIO_S4>; // 1.8V
-			qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
-			bias-pull-down;
-		};
-	};
-
-	audio_mclk: clk_div1 {
-		pinconf {
-			pins = "gpio15";
-			function = "func1";
-			power-source = <PM8994_GPIO_S4>; // 1.8V
-		};
-	};
-
-	volume_up_gpio: pm8996_gpio2 {
-		pinconf {
-			pins = "gpio2";
-			function = "normal";
-			input-enable;
-			drive-push-pull;
-			bias-pull-up;
-			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
-			power-source = <PM8994_GPIO_S4>; // 1.8V
-		};
-	};
-
-	divclk4_pin_a: divclk4 {
-		pinconf {
-			pins = "gpio18";
-			function = PMIC_GPIO_FUNC_FUNC2;
-
-			bias-disable;
-			power-source = <PM8994_GPIO_S4>;
-		};
-	};
-
-	usb3_vbus_det_gpio: pm8996_gpio22 {
-		pinconf {
-			pins = "gpio22";
-			function = PMIC_GPIO_FUNC_NORMAL;
-			input-enable;
-			bias-pull-down;
-			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
-			power-source = <PM8994_GPIO_S4>; // 1.8V
-		};
-	};
-};
-
-&pmi8994_gpios {
-	usb2_vbus_det_gpio: pmi8996_gpio6 {
-		pinconf {
-			pins = "gpio6";
-			function = PMIC_GPIO_FUNC_NORMAL;
-			input-enable;
-			bias-pull-down;
-			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
-			power-source = <PM8994_GPIO_S4>; // 1.8V
-		};
-	};
-};

arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts

+// SPDX-License-Identifier: BSD-3-Clause
+
+/dts-v1/;
+
+#include "msm8996.dtsi"
+#include "pm8994.dtsi"
+#include "pmi8994.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "Inforce 6640 Single Board Computer";
+	compatible = "inforce,ifc6640", "qcom,apq8096-sbc", "qcom,apq8096";
+
+	qcom,msm-id = <291 0x00030001>;
+	qcom,board-id = <0x00010018 0>;
+
+	aliases {
+		serial0 = &blsp2_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	v1p05: v1p05-regulator {
+		compatible = "regulator-fixed";
+		reglator-name = "v1p05";
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1050000>;
+
+		vin-supply = <&v5p0>;
+	};
+
+	v12_poe: v12-poe-regulator {
+		compatible = "regulator-fixed";
+		reglator-name = "v12_poe";
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	v3p3: v3p3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v3p3";
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		vin-supply = <&v12_poe>;
+	};
+
+	v5p0: v5p0-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v5p0";
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		vin-supply = <&v12_poe>;
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-min-microvolt = <3800000>;
+		regulator-max-microvolt = <3800000>;
+	};
+};
+
+&blsp2_uart1 {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&blsp2_uart1_2pins_default>;
+	pinctrl-1 = <&blsp2_uart1_2pins_sleep>;
+};
+
+&msmgpio {
+	sdc2_pins_default: sdc2-pins-default {
+		clk {
+			pins = "sdc2_clk";
+			bias-disable;
+			drive-strength = <16>;
+		};
+
+		cmd {
+			pins = "sdc2_cmd";
+			bias-pull-up;
+			drive-strength = <10>;
+		};
+
+		data {
+			pins = "sdc2_data";
+			bias-pull-up;
+			drive-strength = <10>;
+		};
+
+		cd {
+			pins = "gpio38";
+			function = "gpio";
+
+			bias-pull-up;
+			drive-strength = <16>;
+		};
+	};
+
+	sdc2_pins_sleep: sdc2-pins-sleep {
+		clk {
+			pins = "sdc2_clk";
+			bias-disable;
+			drive-strength = <2>;
+		};
+
+		cmd {
+			pins = "sdc2_cmd";
+			bias-pull-up;
+			drive-strength = <2>;
+		};
+
+		data {
+			pins = "sdc2_data";
+			bias-pull-up;
+			drive-strength = <2>;
+		};
+
+		cd {
+			pins = "gpio38";
+			function = "gpio";
+			bias-pull-up;
+			drive-strength = <2>;
+		};
+	};
+};
+
+&rpm_requests {
+	pm8994-regulators {
+		compatible = "qcom,rpm-pm8994-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_s8-supply = <&vph_pwr>;
+		vdd_s9-supply = <&vph_pwr>;
+		vdd_s10-supply = <&vph_pwr>;
+		vdd_s11-supply = <&vph_pwr>;
+		vdd_s12-supply = <&vph_pwr>;
+		vdd_l2_l26_l28-supply = <&vreg_s3a_1p3>;
+		vdd_l3_l11-supply = <&vreg_s3a_1p3>;
+		vdd_l4_l27_l31-supply = <&vreg_s3a_1p3>;
+		vdd_l5_l7-supply = <&vreg_s5a_2p15>;
+		vdd_l6_l12_l32-supply = <&vreg_s5a_2p15>;
+		vdd_l8_l16_l30-supply = <&vph_pwr>;
+		vdd_l25-supply = <&vreg_s3a_1p3>;
+		vdd_lvs1_2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p3: s3 {
+			regulator-name = "vreg_s3a_1p3";
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		vreg_s4a_1p8: s4 {
+			regulator-name = "vreg_s4a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+		vreg_s5a_2p15: s5 {
+			regulator-name = "vreg_s5a_2p15";
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+		};
+		vreg_s7a_1p0: s7 {
+			regulator-name = "vreg_s7a_1p0";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l1a_1p0: l1 {
+			regulator-name = "vreg_l1a_1p0";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+		vreg_l2a_1p25: l2 {
+			regulator-name = "vreg_l2a_1p25";
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+		};
+		vreg_l3a_0p875: l3 {
+			regulator-name = "vreg_l3a_0p875";
+			regulator-min-microvolt = <850000>;
+			regulator-max-microvolt = <850000>;
+		};
+		vreg_l4a_1p225: l4 {
+			regulator-name = "vreg_l4a_1p225";
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		vreg_l6a_1p2: l6 {
+			regulator-name = "vreg_l6a_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		vreg_l8a_1p8: l8 {
+			regulator-name = "vreg_l8a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l9a_1p8: l9 {
+			regulator-name = "vreg_l9a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l10a_1p8: l10 {
+			regulator-name = "vreg_l10a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l11a_1p15: l11 {
+			regulator-name = "vreg_l11a_1p15";
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+		vreg_l12a_1p8: l12 {
+			regulator-name = "vreg_l12a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l13a_2p95: l13 {
+			regulator-name = "vreg_l13a_2p95";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		vreg_l14a_1p8: l14 {
+			regulator-name = "vreg_l14a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l15a_1p8: l15 {
+			regulator-name = "vreg_l15a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l16a_2p7: l16 {
+			regulator-name = "vreg_l16a_2p7";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+		vreg_l17a_2p8: l17 {
+			regulator-name = "vreg_l17a_2p8";
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+		};
+		vreg_l18a_2p85: l18 {
+			regulator-name = "vreg_l18a_2p85";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2900000>;
+		};
+		vreg_l19a_2p8: l19 {
+			regulator-name = "vreg_l19a_2p8";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		vreg_l20a_2p95: l20 {
+			regulator-name = "vreg_l20a_2p95";
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+		vreg_l21a_2p95: l21 {
+			regulator-name = "vreg_l21a_2p95";
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		vreg_l22a_3p0: l22 {
+			regulator-name = "vreg_l22a_3p0";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+		vreg_l23a_2p8: l23 {
+			regulator-name = "vreg_l23a_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+		vreg_l24a_3p075: l24 {
+			regulator-name = "vreg_l24a_3p075";
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+		vreg_l25a_1p2: l25 {
+			regulator-name = "vreg_l25a_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-allow-set-load;
+		};
+		vreg_l26a_0p8: l27 {
+			regulator-name = "vreg_l26a_0p8";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+		vreg_l28a_0p925: l28 {
+			regulator-name = "vreg_l28a_0p925";
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <925000>;
+			regulator-allow-set-load;
+		};
+		vreg_l29a_2p8: l29 {
+			regulator-name = "vreg_l29a_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+		vreg_l30a_1p8: l30 {
+			regulator-name = "vreg_l30a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l32a_1p8: l32 {
+			regulator-name = "vreg_l32a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_lvs1a_1p8: lvs1 {
+			regulator-name = "vreg_lvs1a_1p8";
+		};
+
+		vreg_lvs2a_1p8: lvs2 {
+			regulator-name = "vreg_lvs2a_1p8";
+		};
+	};
+};
+
+&sdhc2 {
+	status = "okay";
+
+	bus-width = <4>;
+
+	cd-gpios = <&msmgpio 38 0x1>;
+
+	vmmc-supply = <&vreg_l21a_2p95>;
+	vqmmc-supply = <&vreg_l13a_2p95>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_pins_default>;
+	pinctrl-1 = <&sdc2_pins_sleep>;
+};
+
+&ufshc {
+	status = "okay";
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vccq-supply = <&vreg_l25a_1p2>;
+	vccq2-supply = <&vreg_s4a_1p8>;
+
+	vcc-max-microamp = <600000>;
+	vccq-max-microamp = <450000>;
+	vccq2-max-microamp = <450000>;
+};
+
+&ufsphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l28a_0p925>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+
+	vdda-phy-max-microamp = <18380>;
+	vdda-pll-max-microamp = <9440>;
+};

arch/arm64/boot/dts/qcom/msm8916.dtsi

@@ -429,7 +429,8 @@ apcs: mailbox@b011000 {
 			compatible = "qcom,msm8916-apcs-kpss-global", "syscon";
 			reg = <0xb011000 0x1000>;
 			#mbox-cells = <1>;
-			clocks = <&a53pll>;
+			clocks = <&a53pll>, <&gcc GPLL0_VOTE>;
+			clock-names = "pll", "aux";
 			#clock-cells = <0>;
 		};
 
@@ -816,6 +817,8 @@ tsens: thermal-sensor@4a9000 {
 			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
 			nvmem-cell-names = "calib", "calib_sel";
 			#qcom,sensors = <5>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
 			#thermal-sensor-cells = <1>;
 		};
 

arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi

@@ -74,6 +74,23 @@ &CPU7 {
 	cpu-idle-states = <&BIG_CPU_SLEEP_1>;
 };
 
+&pm8005_lsid1 {
+	pm8005-regulators {
+		compatible = "qcom,pm8005-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+
+		pm8005_s1: s1 { /* VDD_GFX supply */
+			regulator-min-microvolt = <524000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-enable-ramp-delay = <500>;
+
+			/* hack until we rig up the gpu consumer */
+			regulator-always-on;
+		};
+	};
+};
+
 &qusb2phy {
 	status = "okay";
 
@@ -292,3 +309,35 @@ &usb3phy {
 	vdda-phy-supply = <&vreg_l1a_0p875>;
 	vdda-pll-supply = <&vreg_l2a_1p2>;
 };
+
+&wifi {
+	status = "okay";
+
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+};
+
+/* PINCTRL - board-specific pinctrl */
+&blsp1_uart3_on {
+	rx {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-up on 45 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		bias-pull-up;
+	};
+
+	cts {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+};

arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi

@@ -9,6 +9,7 @@
 / {
 	aliases {
 		serial0 = &blsp2_uart1;
+		serial1 = &blsp1_uart3;
 	};
 
 	chosen {
@@ -311,6 +312,14 @@ vreg_bob: bob {
 	};
 };
 
+&remoteproc_adsp {
+	status = "okay";
+};
+
+&remoteproc_slpi {
+	status = "okay";
+};
+
 &tlmm {
 	gpio-reserved-ranges = <0 4>, <81 4>;
 };
@@ -364,3 +373,35 @@ &usb3phy {
 	vdda-phy-supply = <&vreg_l1a_0p875>;
 	vdda-pll-supply = <&vreg_l2a_1p2>;
 };
+
+&wifi {
+	status = "okay";
+
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+};
+
+/* PINCTRL - board-specific pinctrl */
+&blsp1_uart3_on {
+	rx {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-up on 45 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		bias-pull-up;
+	};
+
+	cts {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+};

arch/arm64/boot/dts/qcom/msm8998-pins.dtsi

@@ -77,13 +77,30 @@ config {
 	};
 
 	blsp1_uart3_on: blsp1_uart3_on {
-		mux {
-			pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		tx {
+			pins = "gpio45";
 			function = "blsp_uart3_a";
+			drive-strength = <2>;
+			bias-disable;
 		};
 
-		config {
-			pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		rx {
+			pins = "gpio46";
+			function = "blsp_uart3_a";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		cts {
+			pins = "gpio47";
+			function = "blsp_uart3_a";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		rfr {
+			pins = "gpio48";
+			function = "blsp_uart3_a";
 			drive-strength = <2>;
 			bias-disable;
 		};

arch/arm64/boot/dts/qcom/msm8998.dtsi

@@ -3,6 +3,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8998.h>
+#include <dt-bindings/clock/qcom,gpucc-msm8998.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -28,8 +29,13 @@ reserved-memory {
 		#size-cells = <2>;
 		ranges;
 
-		memory@85800000 {
-			reg = <0x0 0x85800000 0x0 0x800000>;
+		hyp_mem: memory@85800000 {
+			reg = <0x0 0x85800000 0x0 0x600000>;
+			no-map;
+		};
+
+		xbl_mem: memory@85e00000 {
+			reg = <0x0 0x85e00000 0x0 0x100000>;
 			no-map;
 		};
 
@@ -38,21 +44,69 @@ smem_mem: smem-mem@86000000 {
 			no-map;
 		};
 
-		memory@86200000 {
+		tz_mem: memory@86200000 {
 			reg = <0x0 0x86200000 0x0 0x2d00000>;
 			no-map;
 		};
 
-		rmtfs {
+		rmtfs_mem: memory@88f00000 {
 			compatible = "qcom,rmtfs-mem";
-
-			size = <0x0 0x200000>;
-			alloc-ranges = <0x0 0xa0000000 0x0 0x2000000>;
+			reg = <0x0 0x88f00000 0x0 0x200000>;
 			no-map;
 
 			qcom,client-id = <1>;
 			qcom,vmid = <15>;
 		};
+
+		spss_mem: memory@8ab00000 {
+			reg = <0x0 0x8ab00000 0x0 0x700000>;
+			no-map;
+		};
+
+		adsp_mem: memory@8b200000 {
+			reg = <0x0 0x8b200000 0x0 0x1a00000>;
+			no-map;
+		};
+
+		mpss_mem: memory@8cc00000 {
+			reg = <0x0 0x8cc00000 0x0 0x7000000>;
+			no-map;
+		};
+
+		venus_mem: memory@93c00000 {
+			reg = <0x0 0x93c00000 0x0 0x500000>;
+			no-map;
+		};
+
+		mba_mem: memory@94100000 {
+			reg = <0x0 0x94100000 0x0 0x200000>;
+			no-map;
+		};
+
+		slpi_mem: memory@94300000 {
+			reg = <0x0 0x94300000 0x0 0xf00000>;
+			no-map;
+		};
+
+		ipa_fw_mem: memory@95200000 {
+			reg = <0x0 0x95200000 0x0 0x10000>;
+			no-map;
+		};
+
+		ipa_gsi_mem: memory@95210000 {
+			reg = <0x0 0x95210000 0x0 0x5000>;
+			no-map;
+		};
+
+		gpu_mem: memory@95600000 {
+			reg = <0x0 0x95600000 0x0 0x100000>;
+			no-map;
+		};
+
+		wlan_msa_mem: memory@95700000 {
+			reg = <0x0 0x95700000 0x0 0x100000>;
+			no-map;
+		};
 	};
 
 	clocks {
@@ -817,8 +871,9 @@ tsens0: thermal@10ab000 {
 			reg = <0x010ab000 0x1000>, /* TM */
 			      <0x010aa000 0x1000>; /* SROT */
 			#qcom,sensors = <14>;
-			interrupts = <GIC_SPI 458 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow";
+			interrupts = <GIC_SPI 458 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 445 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
 		};
 
@@ -827,8 +882,9 @@ tsens1: thermal@10ae000 {
 			reg = <0x010ae000 0x1000>, /* TM */
 			      <0x010ad000 0x1000>; /* SROT */
 			#qcom,sensors = <8>;
-			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow";
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
 		};
 
@@ -847,6 +903,25 @@ anoc1_smmu: iommu@1680000 {
 				<GIC_SPI 369 IRQ_TYPE_EDGE_RISING>;
 		};
 
+		anoc2_smmu: iommu@16c0000 {
+			compatible = "qcom,msm8998-smmu-v2", "qcom,smmu-v2";
+			reg = <0x016c0000 0x40000>;
+			#iommu-cells = <1>;
+
+			#global-interrupts = <0>;
+			interrupts =
+				<GIC_SPI 373 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 374 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 375 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 376 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 377 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 378 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 462 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 463 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 464 IRQ_TYPE_EDGE_RISING>,
+				<GIC_SPI 465 IRQ_TYPE_EDGE_RISING>;
+		};
+
 		pcie0: pci@1c00000 {
 			compatible = "qcom,pcie-msm8996";
 			reg =	<0x01c00000 0x2000>,
@@ -987,7 +1062,7 @@ ufsphy_lanes: lanes@1da7400 {
 
 		tcsr_mutex_regs: syscon@1f40000 {
 			compatible = "syscon";
-			reg = <0x01f40000 0x20000>;
+			reg = <0x01f40000 0x40000>;
 		};
 
 		tlmm: pinctrl@3400000 {
@@ -1000,6 +1075,110 @@ tlmm: pinctrl@3400000 {
 			#interrupt-cells = <0x2>;
 		};
 
+		remoteproc_mss: remoteproc@4080000 {
+			compatible = "qcom,msm8998-mss-pil";
+			reg = <0x04080000 0x100>, <0x04180000 0x20>;
+			reg-names = "qdsp6", "rmb";
+
+			interrupts-extended =
+				<&intc GIC_SPI 448 IRQ_TYPE_EDGE_RISING>,
+				<&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+				<&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+				<&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+				<&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+				<&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack",
+					  "shutdown-ack";
+
+			clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+				 <&gcc GCC_BIMC_MSS_Q6_AXI_CLK>,
+				 <&gcc GCC_BOOT_ROM_AHB_CLK>,
+				 <&gcc GCC_MSS_GPLL0_DIV_CLK_SRC>,
+				 <&gcc GCC_MSS_SNOC_AXI_CLK>,
+				 <&gcc GCC_MSS_MNOC_BIMC_AXI_CLK>,
+				 <&rpmcc RPM_SMD_QDSS_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface", "bus", "mem", "gpll0_mss",
+				      "snoc_axi", "mnoc_axi", "qdss", "xo";
+
+			qcom,smem-states = <&modem_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			resets = <&gcc GCC_MSS_RESTART>;
+			reset-names = "mss_restart";
+
+			qcom,halt-regs = <&tcsr_mutex_regs 0x23000 0x25000 0x24000>;
+
+			power-domains = <&rpmpd MSM8998_VDDCX>,
+					<&rpmpd MSM8998_VDDMX>;
+			power-domain-names = "cx", "mx";
+
+			mba {
+				memory-region = <&mba_mem>;
+			};
+
+			mpss {
+				memory-region = <&mpss_mem>;
+			};
+
+			glink-edge {
+				interrupts = <GIC_SPI 452 IRQ_TYPE_EDGE_RISING>;
+				label = "modem";
+				qcom,remote-pid = <1>;
+				mboxes = <&apcs_glb 15>;
+			};
+		};
+
+		gpucc: clock-controller@5065000 {
+			compatible = "qcom,msm8998-gpucc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			reg = <0x05065000 0x9000>;
+
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+				 <&gcc GPLL0_OUT_MAIN>;
+			clock-names = "xo",
+				      "gpll0";
+		};
+
+		remoteproc_slpi: remoteproc@5800000 {
+			compatible = "qcom,msm8998-slpi-pas";
+			reg = <0x05800000 0x4040>;
+
+			interrupts-extended = <&intc GIC_SPI 390 IRQ_TYPE_EDGE_RISING>,
+					      <&slpi_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&slpi_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&slpi_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&slpi_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			px-supply = <&vreg_lvs2a_1p8>;
+
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+				 <&rpmcc RPM_SMD_AGGR2_NOC_CLK>;
+			clock-names = "xo", "aggre2";
+
+			memory-region = <&slpi_mem>;
+
+			qcom,smem-states = <&slpi_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			power-domains = <&rpmpd MSM8998_SSCCX>;
+			power-domain-names = "ssc_cx";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts = <GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
+				label = "dsps";
+				qcom,remote-pid = <3>;
+				mboxes = <&apcs_glb 27>;
+			};
+		};
+
 		stm: stm@6002000 {
 			compatible = "arm,coresight-stm", "arm,primecell";
 			reg = <0x06002000 0x1000>,
@@ -1792,6 +1971,39 @@ blsp2_i2c5: i2c@c1ba000 {
 			#size-cells = <0>;
 		};
 
+		remoteproc_adsp: remoteproc@17300000 {
+			compatible = "qcom,msm8998-adsp-pas";
+			reg = <0x17300000 0x4040>;
+
+			interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "xo";
+
+			memory-region = <&adsp_mem>;
+
+			qcom,smem-states = <&adsp_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			power-domains = <&rpmpd MSM8998_VDDCX>;
+			power-domain-names = "cx";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>;
+				label = "lpass";
+				qcom,remote-pid = <2>;
+				mboxes = <&apcs_glb 9>;
+			};
+		};
+
 		apcs_glb: mailbox@17911000 {
 			compatible = "qcom,msm8998-apcs-hmss-global";
 			reg = <0x17911000 0x1000>;
@@ -1870,6 +2082,32 @@ intc: interrupt-controller@17a00000 {
 			redistributor-stride = <0x0 0x20000>;
 			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
 		};
+
+		wifi: wifi@18800000 {
+			compatible = "qcom,wcn3990-wifi";
+			status = "disabled";
+			reg = <0x18800000 0x800000>;
+			reg-names = "membase";
+			memory-region = <&wlan_msa_mem>;
+			clocks = <&rpmcc RPM_SMD_RF_CLK2_PIN>;
+			clock-names = "cxo_ref_clk_pin";
+			interrupts =
+				<GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>;
+			iommus = <&anoc2_smmu 0x1900>,
+				 <&anoc2_smmu 0x1901>;
+			qcom,snoc-host-cap-8bit-quirk;
+		};
 	};
 };
 

arch/arm64/boot/dts/qcom/pm6150.dtsi

+// SPDX-License-Identifier: BSD-3-Clause
+// Copyright (c) 2019, The Linux Foundation. All rights reserved.
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/thermal/thermal.h>
+
+&spmi_bus {
+	pm6150_lsid0: pmic@0 {
+		compatible = "qcom,pm6150", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm6150_pon: pon@800 {
+			compatible = "qcom,pm8998-pon";
+			reg = <0x800>;
+			mode-bootloader = <0x2>;
+			mode-recovery = <0x1>;
+
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+			};
+		};
+
+		pm6150_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pm6150_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm6150_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			adc-chan@6 {
+				reg = <ADC5_DIE_TEMP>;
+				label = "die_temp";
+			};
+		};
+
+		pm6150_gpio: gpios@c000 {
+			compatible = "qcom,pm6150-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm6150_gpio 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm6150_lsid1: pmic@1 {
+		compatible = "qcom,pm6150", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};

arch/arm64/boot/dts/qcom/pm6150l.dtsi

+// SPDX-License-Identifier: BSD-3-Clause
+// Copyright (c) 2019, The Linux Foundation. All rights reserved.
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pm6150l_lsid4: pmic@4 {
+		compatible = "qcom,pm6150l", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm6150l_gpio: gpios@c000 {
+			compatible = "qcom,pm6150l-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm6150l_gpio 0 0 12>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm6150l_lsid5: pmic@5 {
+		compatible = "qcom,pm6150l", "qcom,spmi-pmic";
+		reg = <0x5 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};

arch/arm64/boot/dts/qcom/pm8004.dtsi

@@ -4,17 +4,23 @@
 
 &spmi_bus {
 
-	pmic@4 {
+	pm8004_lsid4: pmic@4 {
 		compatible = "qcom,pm8004", "qcom,spmi-pmic";
 		reg = <0x4 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+		status = "disabled";
 	};
 
-	pmic@5 {
+	pm8004_lsid5: pmic@5 {
 		compatible = "qcom,pm8004", "qcom,spmi-pmic";
 		reg = <0x5 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+		status = "disabled";
+
+		pm8004_spmi_regulators: regulators {
+			compatible = "qcom,pm8004-regulators";
+		};
 	};
 };

arch/arm64/boot/dts/qcom/pm8916.dtsi

@@ -111,6 +111,12 @@ pm8916_1: pm8916@1 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pm8916_vib: vibrator@c000 {
+			compatible = "qcom,pm8916-vib";
+			reg = <0xc000>;
+			status = "disabled";
+		};
+
 		wcd_codec: codec@f000 {
 			compatible = "qcom,pm8916-wcd-analog-codec";
 			reg = <0xf000 0x200>;

arch/arm64/boot/dts/qcom/pm8994.dtsi

@@ -85,5 +85,9 @@ pmic@1 {
 		reg = <0x1 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+
+		pm8994_spmi_regulators: regulators {
+			compatible = "qcom,pm8994-regulators";
+		};
 	};
 };

arch/arm64/boot/dts/qcom/qcs404-evb.dtsi

@@ -73,6 +73,7 @@ pms405_s3: s3 {
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-name = "vdd_apc";
+		regulator-initial-mode = <1>;
 		regulator-min-microvolt = <1048000>;
 		regulator-max-microvolt = <1384000>;
 	};

arch/arm64/boot/dts/qcom/qcs404.dtsi

@@ -42,6 +42,10 @@ CPU0: cpu@100 {
 			cpu-idle-states = <&CPU_SLEEP_0>;
 			next-level-cache = <&L2_0>;
 			#cooling-cells = <2>;
+			clocks = <&apcs_glb>;
+			operating-points-v2 = <&cpu_opp_table>;
+			power-domains = <&cpr>;
+			power-domain-names = "cpr";
 		};
 
 		CPU1: cpu@101 {
@@ -52,6 +56,10 @@ CPU1: cpu@101 {
 			cpu-idle-states = <&CPU_SLEEP_0>;
 			next-level-cache = <&L2_0>;
 			#cooling-cells = <2>;
+			clocks = <&apcs_glb>;
+			operating-points-v2 = <&cpu_opp_table>;
+			power-domains = <&cpr>;
+			power-domain-names = "cpr";
 		};
 
 		CPU2: cpu@102 {
@@ -62,6 +70,10 @@ CPU2: cpu@102 {
 			cpu-idle-states = <&CPU_SLEEP_0>;
 			next-level-cache = <&L2_0>;
 			#cooling-cells = <2>;
+			clocks = <&apcs_glb>;
+			operating-points-v2 = <&cpu_opp_table>;
+			power-domains = <&cpr>;
+			power-domain-names = "cpr";
 		};
 
 		CPU3: cpu@103 {
@@ -72,6 +84,10 @@ CPU3: cpu@103 {
 			cpu-idle-states = <&CPU_SLEEP_0>;
 			next-level-cache = <&L2_0>;
 			#cooling-cells = <2>;
+			clocks = <&apcs_glb>;
+			operating-points-v2 = <&cpu_opp_table>;
+			power-domains = <&cpr>;
+			power-domain-names = "cpr";
 		};
 
 		L2_0: l2-cache {
@@ -94,6 +110,41 @@ CPU_SLEEP_0: cpu-sleep-0 {
 		};
 	};
 
+	cpu_opp_table: cpu-opp-table {
+		compatible = "operating-points-v2-kryo-cpu";
+		opp-shared;
+
+		opp-1094400000 {
+			opp-hz = /bits/ 64 <1094400000>;
+			required-opps = <&cpr_opp1>;
+		};
+		opp-1248000000 {
+			opp-hz = /bits/ 64 <1248000000>;
+			required-opps = <&cpr_opp2>;
+		};
+		opp-1401600000 {
+			opp-hz = /bits/ 64 <1401600000>;
+			required-opps = <&cpr_opp3>;
+		};
+	};
+
+	cpr_opp_table: cpr-opp-table {
+		compatible = "operating-points-v2-qcom-level";
+
+		cpr_opp1: opp1 {
+			opp-level = <1>;
+			qcom,opp-fuse-level = <1>;
+		};
+		cpr_opp2: opp2 {
+			opp-level = <2>;
+			qcom,opp-fuse-level = <2>;
+		};
+		cpr_opp3: opp3 {
+			opp-level = <3>;
+			qcom,opp-fuse-level = <3>;
+		};
+	};
+
 	firmware {
 		scm: scm {
 			compatible = "qcom,scm-qcs404", "qcom,scm";
@@ -280,6 +331,62 @@ qfprom: qfprom@a4000 {
 			tsens_caldata: caldata@d0 {
 				reg = <0x1f8 0x14>;
 			};
+			cpr_efuse_speedbin: speedbin@13c {
+				reg = <0x13c 0x4>;
+				bits = <2 3>;
+			};
+			cpr_efuse_quot_offset1: qoffset1@231 {
+				reg = <0x231 0x4>;
+				bits = <4 7>;
+			};
+			cpr_efuse_quot_offset2: qoffset2@232 {
+				reg = <0x232 0x4>;
+				bits = <3 7>;
+			};
+			cpr_efuse_quot_offset3: qoffset3@233 {
+				reg = <0x233 0x4>;
+				bits = <2 7>;
+			};
+			cpr_efuse_init_voltage1: ivoltage1@229 {
+				reg = <0x229 0x4>;
+				bits = <4 6>;
+			};
+			cpr_efuse_init_voltage2: ivoltage2@22a {
+				reg = <0x22a 0x4>;
+				bits = <2 6>;
+			};
+			cpr_efuse_init_voltage3: ivoltage3@22b {
+				reg = <0x22b 0x4>;
+				bits = <0 6>;
+			};
+			cpr_efuse_quot1: quot1@22b {
+				reg = <0x22b 0x4>;
+				bits = <6 12>;
+			};
+			cpr_efuse_quot2: quot2@22d {
+				reg = <0x22d 0x4>;
+				bits = <2 12>;
+			};
+			cpr_efuse_quot3: quot3@230 {
+				reg = <0x230 0x4>;
+				bits = <0 12>;
+			};
+			cpr_efuse_ring1: ring1@228 {
+				reg = <0x228 0x4>;
+				bits = <0 3>;
+			};
+			cpr_efuse_ring2: ring2@228 {
+				reg = <0x228 0x4>;
+				bits = <4 3>;
+			};
+			cpr_efuse_ring3: ring3@229 {
+				reg = <0x229 0x4>;
+				bits = <0 3>;
+			};
+			cpr_efuse_revision: revision@218 {
+				reg = <0x218 0x4>;
+				bits = <3 3>;
+			};
 		};
 
 		rng: rng@e3000 {
@@ -902,14 +1009,65 @@ apcs_glb: mailbox@b011000 {
 			compatible = "qcom,qcs404-apcs-apps-global", "syscon";
 			reg = <0x0b011000 0x1000>;
 			#mbox-cells = <1>;
+			clocks = <&apcs_hfpll>, <&gcc GCC_GPLL0_AO_OUT_MAIN>;
+			clock-names = "pll", "aux";
+			#clock-cells = <0>;
+		};
+
+		apcs_hfpll: clock-controller@b016000 {
+			compatible = "qcom,hfpll";
+			reg = <0x0b016000 0x30>;
+			#clock-cells = <0>;
+			clock-output-names = "apcs_hfpll";
+			clocks = <&xo_board>;
+			clock-names = "xo";
 		};
 
 		watchdog@b017000 {
-			compatible = "qcom,kpss-wdt";
+			compatible = "qcom,apss-wdt-qcs404", "qcom,kpss-wdt";
 			reg = <0x0b017000 0x1000>;
 			clocks = <&sleep_clk>;
 		};
 
+		cpr: power-controller@b018000 {
+			compatible = "qcom,qcs404-cpr", "qcom,cpr";
+			reg = <0x0b018000 0x1000>;
+			interrupts = <0 15 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&xo_board>;
+			clock-names = "ref";
+			vdd-apc-supply = <&pms405_s3>;
+			#power-domain-cells = <0>;
+			operating-points-v2 = <&cpr_opp_table>;
+			acc-syscon = <&tcsr>;
+
+			nvmem-cells = <&cpr_efuse_quot_offset1>,
+				<&cpr_efuse_quot_offset2>,
+				<&cpr_efuse_quot_offset3>,
+				<&cpr_efuse_init_voltage1>,
+				<&cpr_efuse_init_voltage2>,
+				<&cpr_efuse_init_voltage3>,
+				<&cpr_efuse_quot1>,
+				<&cpr_efuse_quot2>,
+				<&cpr_efuse_quot3>,
+				<&cpr_efuse_ring1>,
+				<&cpr_efuse_ring2>,
+				<&cpr_efuse_ring3>,
+				<&cpr_efuse_revision>;
+			nvmem-cell-names = "cpr_quotient_offset1",
+				"cpr_quotient_offset2",
+				"cpr_quotient_offset3",
+				"cpr_init_voltage1",
+				"cpr_init_voltage2",
+				"cpr_init_voltage3",
+				"cpr_quotient1",
+				"cpr_quotient2",
+				"cpr_quotient3",
+				"cpr_ring_osc1",
+				"cpr_ring_osc2",
+				"cpr_ring_osc3",
+				"cpr_fuse_revision";
+		};
+
 		timer@b120000 {
 			#address-cells = <1>;
 			#size-cells = <1>;

arch/arm64/boot/dts/qcom/sc7180-idp.dts

+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * SC7180 IDP board device tree source
+ *
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sc7180.dtsi"
+#include "pm6150.dtsi"
+#include "pm6150l.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SC7180 IDP";
+	compatible = "qcom,sc7180-idp", "qcom,sc7180";
+
+	aliases {
+		hsuart0 = &uart3;
+		serial0 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&apps_rsc {
+	pm6150-rpmh-regulators {
+		compatible = "qcom,pm6150-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_s1a_1p1: smps1 {
+			regulator-min-microvolt = <1128000>;
+			regulator-max-microvolt = <1128000>;
+		};
+
+		vreg_s4a_1p0: smps4 {
+			regulator-min-microvolt = <824000>;
+			regulator-max-microvolt = <1120000>;
+		};
+
+		vreg_s5a_2p0: smps5 {
+			regulator-min-microvolt = <1744000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_l1a_1p2: ldo1 {
+			regulator-min-microvolt = <1178000>;
+			regulator-max-microvolt = <1256000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l2a_1p0: ldo2 {
+			regulator-min-microvolt = <944000>;
+			regulator-max-microvolt = <1056000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l3a_1p0: ldo3 {
+			regulator-min-microvolt = <968000>;
+			regulator-max-microvolt = <1064000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l4a_0p8: ldo4 {
+			regulator-min-microvolt = <824000>;
+			regulator-max-microvolt = <928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l5a_2p7: ldo5 {
+			regulator-min-microvolt = <2496000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l6a_0p6: ldo6 {
+			regulator-min-microvolt = <568000>;
+			regulator-max-microvolt = <648000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l9a_0p6: ldo9 {
+			regulator-min-microvolt = <488000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l10a_1p8: ldo10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1832000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l11a_1p8: ldo11 {
+			regulator-min-microvolt = <1696000>;
+			regulator-max-microvolt = <1904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1696000>;
+			regulator-max-microvolt = <1952000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l13a_1p8: ldo13 {
+			regulator-min-microvolt = <1696000>;
+			regulator-max-microvolt = <1904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l14a_1p8: ldo14 {
+			regulator-min-microvolt = <1728000>;
+			regulator-max-microvolt = <1832000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l15a_1p8: ldo15 {
+			regulator-min-microvolt = <1696000>;
+			regulator-max-microvolt = <1904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l16a_2p7: ldo16 {
+			regulator-min-microvolt = <2496000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l17a_3p0: ldo17 {
+			regulator-min-microvolt = <2920000>;
+			regulator-max-microvolt = <3232000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l18a_2p8: ldo18 {
+			regulator-min-microvolt = <2496000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l19a_2p9: ldo19 {
+			regulator-min-microvolt = <2696000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+	};
+
+	pm6150l-rpmh-regulators {
+		compatible = "qcom,pm6150l-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_s8c_1p3: smps8 {
+			regulator-min-microvolt = <1120000>;
+			regulator-max-microvolt = <1408000>;
+		};
+
+		vreg_l1c_1p8: ldo1 {
+			regulator-min-microvolt = <1616000>;
+			regulator-max-microvolt = <1984000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l2c_1p3: ldo2 {
+			regulator-min-microvolt = <1168000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l3c_1p2: ldo3 {
+			regulator-min-microvolt = <1144000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l4c_1p8: ldo4 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l5c_1p8: ldo5 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l6c_2p9: ldo6 {
+			regulator-min-microvolt = <2696000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l7c_3p0: ldo7 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l8c_1p8: ldo8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l9c_2p9: ldo9 {
+			regulator-min-microvolt = <2952000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l10c_3p3: ldo10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l11c_3p3: ldo11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+		};
+	};
+};
+
+&qspi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_clk &qspi_cs0 &qspi_data01>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart8 {
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+	vdd-supply = <&vreg_l4a_0p8>;
+	vdda-pll-supply = <&vreg_l11a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l17a_3p0>;
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+	vdda-phy-supply = <&vreg_l3c_1p2>;
+	vdda-pll-supply = <&vreg_l4a_0p8>;
+};
+
+/* PINCTRL - additions to nodes defined in sc7180.dtsi */
+
+&qspi_clk {
+	pinconf {
+		pins = "gpio63";
+		bias-disable;
+	};
+};
+
+&qspi_cs0 {
+	pinconf {
+		pins = "gpio68";
+		bias-disable;
+	};
+};
+
+&qspi_data01 {
+	pinconf {
+		pins = "gpio64", "gpio65";
+
+		/* High-Z when no transfers; nice to park the lines */
+		bias-pull-up;
+	};
+};
+
+&qup_i2c2_default {
+	pinconf {
+		pins = "gpio15", "gpio16";
+		drive-strength = <2>;
+
+		/* Has external pullup */
+		bias-disable;
+	};
+};
+
+&qup_i2c4_default {
+	pinconf {
+		pins = "gpio115", "gpio116";
+		drive-strength = <2>;
+
+		/* Has external pullup */
+		bias-disable;
+	};
+};
+
+&qup_i2c7_default {
+	pinconf {
+		pins = "gpio6", "gpio7";
+		drive-strength = <2>;
+
+		/* Has external pullup */
+		bias-disable;
+	};
+};
+
+&qup_i2c9_default {
+	pinconf {
+		pins = "gpio46", "gpio47";
+		drive-strength = <2>;
+
+		/* Has external pullup */
+		bias-disable;
+	};
+};
+
+&qup_uart3_default {
+	pinconf-cts {
+		/*
+		 * Configure a pull-down on 38 (CTS) to match the pull of
+		 * the Bluetooth module.
+		 */
+		pins = "gpio38";
+		bias-pull-down;
+		output-high;
+	};
+
+	pinconf-rts {
+		/* We'll drive 39 (RTS), so no pull */
+		pins = "gpio39";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pinconf-tx {
+		/* We'll drive 40 (TX), so no pull */
+		pins = "gpio40";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	pinconf-rx {
+		/*
+		 * Configure a pull-up on 41 (RX). This is needed to avoid
+		 * garbage data when the TX pin of the Bluetooth module is
+		 * in tri-state (module powered off or not driving the
+		 * signal yet).
+		 */
+		pins = "gpio41";
+		bias-pull-up;
+	};
+};
+
+&qup_uart8_default {
+	pinconf-tx {
+		pins = "gpio44";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pinconf-rx {
+		pins = "gpio45";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&qup_spi0_default {
+	pinconf {
+		pins = "gpio34", "gpio35", "gpio36", "gpio37";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&qup_spi6_default {
+	pinconf {
+		pins = "gpio59", "gpio60", "gpio61", "gpio62";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&qup_spi10_default {
+	pinconf {
+		pins = "gpio86", "gpio87", "gpio88", "gpio89";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+

arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi

@@ -165,7 +165,6 @@ panel_in_edp: endpoint {
 /delete-node/ &venus_mem;
 /delete-node/ &cdsp_mem;
 /delete-node/ &cdsp_pas;
-/delete-node/ &zap_shader;
 /delete-node/ &gpu_mem;
 
 /* Increase the size from 120 MB to 128 MB */
@@ -651,6 +650,20 @@ &spi0 {
 	status = "okay";
 };
 
+&spi5 {
+	status = "okay";
+
+	tpm@0 {
+		compatible = "google,cr50";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&h1_ap_int_odl>;
+		spi-max-frequency = <800000>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <129 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
 &spi10 {
 	status = "okay";
 

arch/arm64/boot/dts/qcom/sdm845-db845c.dts

@@ -197,7 +197,7 @@ vph_pwr: vph-pwr-regulator {
 &adsp_pas {
 	status = "okay";
 
-	firmware-name = "qcom/db845c/adsp.mdt";
+	firmware-name = "qcom/sdm845/adsp.mdt";
 };
 
 &apps_rsc {
@@ -343,7 +343,7 @@ vreg_bob: bob {
 
 &cdsp_pas {
 	status = "okay";
-	firmware-name = "qcom/db845c/cdsp.mdt";
+	firmware-name = "qcom/sdm845/cdsp.mdt";
 };
 
 &gcc {
@@ -352,6 +352,18 @@ &gcc {
 			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
 };
 
+&gpu {
+	zap-shader {
+		memory-region = <&gpu_mem>;
+		firmware-name = "qcom/sdm845/a630_zap.mbn";
+	};
+};
+
+&mss_pil {
+	status = "okay";
+	firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn";
+};
+
 &pm8998_gpio {
 	vol_up_pin_a: vol-up-active {
 		pins = "gpio6";
@@ -529,6 +541,8 @@ &wifi {
 	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
 	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
 	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+
+	qcom,snoc-host-cap-8bit-quirk;
 };
 
 /* PINCTRL - additions to nodes defined in sdm845.dtsi */

arch/arm64/boot/dts/qcom/sdm845-mtp.dts

@@ -360,6 +360,13 @@ &gcc {
 			   <GCC_LPASS_SWAY_CLK>;
 };
 
+&gpu {
+	zap-shader {
+		memory-region = <&gpu_mem>;
+		firmware-name = "qcom/sdm845/a630_zap.mbn";
+	};
+};
+
 &i2c10 {
 	status = "okay";
 	clock-frequency = <400000>;

arch/arm64/boot/dts/qcom/sdm845.dtsi

@@ -1357,7 +1357,7 @@ uart15: serial@a9c000 {
 			};
 		};
 
-		cache-controller@1100000 {
+		system-cache-controller@1100000 {
 			compatible = "qcom,sdm845-llcc";
 			reg = <0 0x01100000 0 0x200000>, <0 0x01300000 0 0x50000>;
 			reg-names = "llcc_base", "llcc_broadcast_base";
@@ -1374,6 +1374,8 @@ ufs_mem_hc: ufshc@1d84000 {
 			lanes-per-direction = <2>;
 			power-domains = <&gcc UFS_PHY_GDSC>;
 			#reset-cells = <1>;
+			resets = <&gcc GCC_UFS_PHY_BCR>;
+			reset-names = "rst";
 
 			iommus = <&apps_smmu 0x100 0xf>;
 
@@ -1447,6 +1449,7 @@ tlmm: pinctrl@3400000 {
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			gpio-ranges = <&tlmm 0 0 150>;
+			wakeup-parent = <&pdc_intc>;
 
 			qspi_clk: qspi-clk {
 				pinmux {
@@ -2804,7 +2807,7 @@ dsi1_phy: dsi-phy@ae96400 {
 			};
 		};
 
-		gpu@5000000 {
+		gpu: gpu@5000000 {
 			compatible = "qcom,adreno-630.2", "qcom,adreno";
 			#stream-id-cells = <16>;
 
@@ -2824,10 +2827,6 @@ gpu@5000000 {
 
 			qcom,gmu = <&gmu>;
 
-			zap_shader: zap-shader {
-				memory-region = <&gpu_mem>;
-			};
-
 			gpu_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
@@ -2939,6 +2938,15 @@ dispcc: clock-controller@af00000 {
 			#power-domain-cells = <1>;
 		};
 
+		pdc_intc: interrupt-controller@b220000 {
+			compatible = "qcom,sdm845-pdc", "qcom,pdc";
+			reg = <0 0x0b220000 0 0x30000>;
+			qcom,pdc-ranges = <0 480 94>, <94 609 15>, <115 630 7>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
 		pdc_reset: reset-controller@b2e0000 {
 			compatible = "qcom,sdm845-pdc-global";
 			reg = <0 0x0b2e0000 0 0x20000>;
@@ -2950,8 +2958,9 @@ tsens0: thermal-sensor@c263000 {
 			reg = <0 0x0c263000 0 0x1ff>, /* TM */
 			      <0 0x0c222000 0 0x1ff>; /* SROT */
 			#qcom,sensors = <13>;
-			interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow";
+			interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
 		};
 
@@ -2960,8 +2969,9 @@ tsens1: thermal-sensor@c265000 {
 			reg = <0 0x0c265000 0 0x1ff>, /* TM */
 			      <0 0x0c223000 0 0x1ff>; /* SROT */
 			#qcom,sensors = <8>;
-			interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow";
+			interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
 		};
 
@@ -3191,7 +3201,7 @@ intc: interrupt-controller@17a00000 {
 			      <0 0x17a60000 0 0x100000>;    /* GICR * 8 */
 			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
 
-			gic-its@17a40000 {
+			msi-controller@17a40000 {
 				compatible = "arm,gic-v3-its";
 				msi-controller;
 				#msi-cells = <1>;

arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts

@@ -245,6 +245,13 @@ &gcc {
 			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
 };
 
+&gpu {
+	zap-shader {
+		memory-region = <&gpu_mem>;
+		firmware-name = "qcom/LENOVO/81JL/qcdxkmsuc850.mbn";
+	};
+};
+
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;

arch/arm64/boot/dts/qcom/sm8150-mtp.dts

@@ -7,6 +7,7 @@
 /dts-v1/;
 
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/gpio/gpio.h>
 #include "sm8150.dtsi"
 #include "pm8150.dtsi"
 #include "pm8150b.dtsi"
@@ -366,6 +367,18 @@ resin {
 	};
 };
 
+&remoteproc_adsp {
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	status = "okay";
+};
+
+&remoteproc_slpi {
+	status = "okay";
+};
+
 &tlmm {
 	gpio-reserved-ranges = <0 4>, <126 4>;
 };
@@ -373,3 +386,25 @@ &tlmm {
 &uart2 {
 	status = "okay";
 };
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l10a_2p5>;
+	vcc-max-microamp = <750000>;
+	vccq-supply = <&vreg_l9a_1p2>;
+	vccq-max-microamp = <700000>;
+	vccq2-supply = <&vreg_s4a_1p8>;
+	vccq2-max-microamp = <750000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_ufs_2ln_core_1>;
+	vdda-max-microamp = <90200>;
+	vdda-pll-supply = <&vreg_l3c_1p2>;
+	vdda-pll-max-microamp = <19000>;
+};