Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC-related driver updates from Olof Johansson:
 "Various driver updates for platforms. A bulk of this is smaller fixes
  or cleanups, but some of the new material this time around is:

   - Support for Nvidia Tegra234 SoC

   - Ring accelerator support for TI AM65x

   - PRUSS driver for TI platforms

   - Renesas support for R-Car V3U SoC

   - Reset support for Cortex-M4 processor on i.MX8MQ

  There are also new socinfo entries for a handful of different SoCs and
  platforms"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
  drm/mediatek: reduce clear event
  soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
  soc: mediatek: cmdq: add jump function
  soc: mediatek: cmdq: add write_s_mask value function
  soc: mediatek: cmdq: add write_s value function
  soc: mediatek: cmdq: add read_s function
  soc: mediatek: cmdq: add write_s_mask function
  soc: mediatek: cmdq: add write_s function
  soc: mediatek: cmdq: add address shift in jump
  soc: mediatek: mtk-infracfg: Fix kerneldoc
  soc: amlogic: pm-domains: use always-on flag
  reset: sti: reset-syscfg: fix struct description warnings
  reset: imx7: add the cm4 reset for i.MX8MQ
  dt-bindings: reset: imx8mq: add m4 reset
  reset: Fix and extend kerneldoc
  reset: reset-zynqmp: Added support for Versal platform
  dt-bindings: reset: Updated binding for Versal reset driver
  reset: imx7: Support module build
  soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
  soc: fsl: qman: convert to use be32_add_cpu()
  ...

Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt

@@ -10,7 +10,8 @@ Required properties:
     "brcm,bcm7038-gisb-arb" for 130nm chips
 - reg: specifies the base physical address and size of the registers
 - interrupts: specifies the two interrupts (timeout and TEA) to be used from
-  the parent interrupt controller
+  the parent interrupt controller. A third optional interrupt may be specified
+  for breakpoints.
 
 Optional properties:
 

Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt

@@ -5,7 +5,7 @@ The hardware block diagram please check bindings/iommu/mediatek,iommu.txt
 Mediatek SMI have two generations of HW architecture, here is the list
 which generation the SoCs use:
 generation 1: mt2701 and mt7623.
-generation 2: mt2712, mt6779, mt8173 and mt8183.
+generation 2: mt2712, mt6779, mt8167, mt8173 and mt8183.
 
 There's slight differences between the two SMI, for generation 2, the
 register which control the iommu port is at each larb's register base. But
@@ -20,6 +20,7 @@ Required properties:
 	"mediatek,mt2712-smi-common"
 	"mediatek,mt6779-smi-common"
 	"mediatek,mt7623-smi-common", "mediatek,mt2701-smi-common"
+	"mediatek,mt8167-smi-common"
 	"mediatek,mt8173-smi-common"
 	"mediatek,mt8183-smi-common"
 - reg : the register and size of the SMI block.

Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt

@@ -8,6 +8,7 @@ Required properties:
 		"mediatek,mt2712-smi-larb"
 		"mediatek,mt6779-smi-larb"
 		"mediatek,mt7623-smi-larb", "mediatek,mt2701-smi-larb"
+		"mediatek,mt8167-smi-larb"
 		"mediatek,mt8173-smi-larb"
 		"mediatek,mt8183-smi-larb"
 - reg : the register and size of this local arbiter.
@@ -22,7 +23,7 @@ Required properties:
   - "gals": the clock for GALS(Global Async Local Sync).
   Here is the list which has this GALS: mt8183.
 
-Required property for mt2701, mt2712, mt6779 and mt7623:
+Required property for mt2701, mt2712, mt6779, mt7623 and mt8167:
 - mediatek,larb-id :the hardware id of this larb.
 
 Example:

Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml

@@ -27,6 +27,7 @@ properties:
       - amlogic,meson8b-pwrc
       - amlogic,meson8m2-pwrc
       - amlogic,meson-gxbb-pwrc
+      - amlogic,meson-axg-pwrc
       - amlogic,meson-g12a-pwrc
       - amlogic,meson-sm1-pwrc
 
@@ -42,11 +43,11 @@ properties:
       - const: vapb
 
   resets:
-    minItems: 11
+    minItems: 5
     maxItems: 12
 
   reset-names:
-    minItems: 11
+    minItems: 5
     maxItems: 12
 
   "#power-domain-cells":
@@ -107,6 +108,24 @@ allOf:
         - resets
         - reset-names
 
+  - if:
+      properties:
+        compatible:
+          enum:
+            - amlogic,meson-axg-pwrc
+    then:
+      properties:
+        reset-names:
+          items:
+            - const: viu
+            - const: venc
+            - const: vcbus
+            - const: vencl
+            - const: vid_lock
+      required:
+        - resets
+        - reset-names
+
   - if:
       properties:
         compatible:

Documentation/devicetree/bindings/power/brcm,bcm63xx-power.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/power/brcm,bcm63xx-power.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: BCM63xx power domain driver
+
+maintainers:
+  - Álvaro Fernández Rojas <noltari@gmail.com>
+
+description: |
+  BCM6318, BCM6328, BCM6362 and BCM63268 SoCs have a power domain controller
+  to enable/disable certain components in order to save power.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - brcm,bcm6318-power-controller
+          - brcm,bcm6328-power-controller
+          - brcm,bcm6362-power-controller
+          - brcm,bcm63268-power-controller
+
+  reg:
+    maxItems: 1
+
+  "#power-domain-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - "#power-domain-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    periph_pwr: power-controller@10001848 {
+        compatible = "brcm,bcm6328-power-controller";
+        reg = <0x10001848 0x4>;
+        #power-domain-cells = <1>;
+    };

Documentation/devicetree/bindings/reset/xlnx,zynqmp-reset.txt

 --------------------------------------------------------------------------
- =  Zynq UltraScale+ MPSoC reset driver binding =
+ =  Zynq UltraScale+ MPSoC and Versal reset driver binding =
 --------------------------------------------------------------------------
-The Zynq UltraScale+ MPSoC has several different resets.
+The Zynq UltraScale+ MPSoC and Versal has several different resets.
 
 See Chapter 36 of the Zynq UltraScale+ MPSoC TRM (UG) for more information
 about zynqmp resets.
@@ -10,7 +10,8 @@ Please also refer to reset.txt in this directory for common reset
 controller binding usage.
 
 Required Properties:
-- compatible:	"xlnx,zynqmp-reset"
+- compatible:	"xlnx,zynqmp-reset" for Zynq UltraScale+ MPSoC platform
+		"xlnx,versal-reset" for Versal platform
 - #reset-cells:	Specifies the number of cells needed to encode reset
 		line, should be 1
 
@@ -37,8 +38,10 @@ Device nodes that need access to reset lines should
 specify them as a reset phandle in their corresponding node as
 specified in reset.txt.
 
-For list of all valid reset indicies see
+For list of all valid reset indices for Zynq UltraScale+ MPSoC see
 <dt-bindings/reset/xlnx-zynqmp-resets.h>
+For list of all valid reset indices for Versal see
+<dt-bindings/reset/xlnx-versal-resets.h>
 
 Example:
 

Documentation/devicetree/bindings/soc/ti/k3-ringacc.yaml

@@ -62,11 +62,6 @@ properties:
     $ref: /schemas/types.yaml#/definitions/uint32
     description: TI-SCI device id of the ring accelerator
 
-  ti,dma-ring-reset-quirk:
-    $ref: /schemas/types.yaml#definitions/flag
-    description: |
-      enable ringacc/udma ring state interoperability issue software w/a
-
 required:
   - compatible
   - reg
@@ -94,7 +89,6 @@ examples:
             reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target";
             ti,num-rings = <818>;
             ti,sci-rm-range-gp-rings = <0x2>; /* GP ring range */
-            ti,dma-ring-reset-quirk;
             ti,sci = <&dmsc>;
             ti,sci-dev-id = <187>;
             msi-parent = <&inta_main_udmass>;

MAINTAINERS

@@ -3482,6 +3482,7 @@ F:	arch/mips/bmips/*
 F:	arch/mips/boot/dts/brcm/bcm*.dts*
 F:	arch/mips/include/asm/mach-bmips/*
 F:	arch/mips/kernel/*bmips*
+F:	drivers/soc/bcm/bcm63xx
 F:	drivers/irqchip/irq-bcm63*
 F:	drivers/irqchip/irq-bcm7*
 F:	drivers/irqchip/irq-brcmstb*

arch/mips/boot/dts/brcm/bcm63268.dtsi

@@ -117,6 +117,12 @@ leds0: led-controller@10001900 {
 			status = "disabled";
 		};
 
+		periph_pwr: power-controller@1000184c {
+			compatible = "brcm,bcm6328-power-controller";
+			reg = <0x1000184c 0x4>;
+			#power-domain-cells = <1>;
+		};
+
 		ehci: usb@10002500 {
 			compatible = "brcm,bcm63268-ehci", "generic-ehci";
 			reg = <0x10002500 0x100>;

arch/mips/boot/dts/brcm/bcm6328.dtsi

@@ -110,6 +110,12 @@ leds0: led-controller@10000800 {
 			status = "disabled";
 		};
 
+		periph_pwr: power-controller@10001848 {
+			compatible = "brcm,bcm6328-power-controller";
+			reg = <0x10001848 0x4>;
+			#power-domain-cells = <1>;
+		};
+
 		ehci: usb@10002500 {
 			compatible = "brcm,bcm6328-ehci", "generic-ehci";
 			reg = <0x10002500 0x100>;

arch/mips/boot/dts/brcm/bcm6362.dtsi

@@ -108,6 +108,12 @@ uart1: serial@10000120 {
 			status = "disabled";
 		};
 
+		periph_pwr: power-controller@10001848 {
+			compatible = "brcm,bcm6362-power-controller";
+			reg = <0x10001848 0x4>;
+			#power-domain-cells = <1>;
+		};
+
 		leds0: led-controller@10001900 {
 			#address-cells = <1>;
 			#size-cells = <0>;

drivers/bus/brcmstb_gisb.c

@@ -30,8 +30,22 @@
 #define  ARB_ERR_CAP_STATUS_WRITE	(1 << 1)
 #define  ARB_ERR_CAP_STATUS_VALID	(1 << 0)
 
+#define  ARB_BP_CAP_CLEAR		(1 << 0)
+#define  ARB_BP_CAP_STATUS_PROT_SHIFT	14
+#define  ARB_BP_CAP_STATUS_TYPE		(1 << 13)
+#define  ARB_BP_CAP_STATUS_RSP_SHIFT	10
+#define  ARB_BP_CAP_STATUS_MASK		GENMASK(1, 0)
+#define  ARB_BP_CAP_STATUS_BS_SHIFT	2
+#define  ARB_BP_CAP_STATUS_WRITE	(1 << 1)
+#define  ARB_BP_CAP_STATUS_VALID	(1 << 0)
+
 enum {
 	ARB_TIMER,
+	ARB_BP_CAP_CLR,
+	ARB_BP_CAP_HI_ADDR,
+	ARB_BP_CAP_ADDR,
+	ARB_BP_CAP_STATUS,
+	ARB_BP_CAP_MASTER,
 	ARB_ERR_CAP_CLR,
 	ARB_ERR_CAP_HI_ADDR,
 	ARB_ERR_CAP_ADDR,
@@ -41,6 +55,11 @@ enum {
 
 static const int gisb_offsets_bcm7038[] = {
 	[ARB_TIMER]		= 0x00c,
+	[ARB_BP_CAP_CLR]	= 0x014,
+	[ARB_BP_CAP_HI_ADDR]	= -1,
+	[ARB_BP_CAP_ADDR]	= 0x0b8,
+	[ARB_BP_CAP_STATUS]	= 0x0c0,
+	[ARB_BP_CAP_MASTER]	= -1,
 	[ARB_ERR_CAP_CLR]	= 0x0c4,
 	[ARB_ERR_CAP_HI_ADDR]	= -1,
 	[ARB_ERR_CAP_ADDR]	= 0x0c8,
@@ -50,6 +69,11 @@ static const int gisb_offsets_bcm7038[] = {
 
 static const int gisb_offsets_bcm7278[] = {
 	[ARB_TIMER]		= 0x008,
+	[ARB_BP_CAP_CLR]	= 0x01c,
+	[ARB_BP_CAP_HI_ADDR]	= -1,
+	[ARB_BP_CAP_ADDR]	= 0x220,
+	[ARB_BP_CAP_STATUS]	= 0x230,
+	[ARB_BP_CAP_MASTER]	= 0x234,
 	[ARB_ERR_CAP_CLR]	= 0x7f8,
 	[ARB_ERR_CAP_HI_ADDR]	= -1,
 	[ARB_ERR_CAP_ADDR]	= 0x7e0,
@@ -59,6 +83,11 @@ static const int gisb_offsets_bcm7278[] = {
 
 static const int gisb_offsets_bcm7400[] = {
 	[ARB_TIMER]		= 0x00c,
+	[ARB_BP_CAP_CLR]	= 0x014,
+	[ARB_BP_CAP_HI_ADDR]	= -1,
+	[ARB_BP_CAP_ADDR]	= 0x0b8,
+	[ARB_BP_CAP_STATUS]	= 0x0c0,
+	[ARB_BP_CAP_MASTER]	= 0x0c4,
 	[ARB_ERR_CAP_CLR]	= 0x0c8,
 	[ARB_ERR_CAP_HI_ADDR]	= -1,
 	[ARB_ERR_CAP_ADDR]	= 0x0cc,
@@ -68,6 +97,11 @@ static const int gisb_offsets_bcm7400[] = {
 
 static const int gisb_offsets_bcm7435[] = {
 	[ARB_TIMER]		= 0x00c,
+	[ARB_BP_CAP_CLR]	= 0x014,
+	[ARB_BP_CAP_HI_ADDR]	= -1,
+	[ARB_BP_CAP_ADDR]	= 0x158,
+	[ARB_BP_CAP_STATUS]	= 0x160,
+	[ARB_BP_CAP_MASTER]	= 0x164,
 	[ARB_ERR_CAP_CLR]	= 0x168,
 	[ARB_ERR_CAP_HI_ADDR]	= -1,
 	[ARB_ERR_CAP_ADDR]	= 0x16c,
@@ -77,6 +111,11 @@ static const int gisb_offsets_bcm7435[] = {
 
 static const int gisb_offsets_bcm7445[] = {
 	[ARB_TIMER]		= 0x008,
+	[ARB_BP_CAP_CLR]	= 0x010,
+	[ARB_BP_CAP_HI_ADDR]	= -1,
+	[ARB_BP_CAP_ADDR]	= 0x1d8,
+	[ARB_BP_CAP_STATUS]	= 0x1e0,
+	[ARB_BP_CAP_MASTER]	= 0x1e4,
 	[ARB_ERR_CAP_CLR]	= 0x7e4,
 	[ARB_ERR_CAP_HI_ADDR]	= 0x7e8,
 	[ARB_ERR_CAP_ADDR]	= 0x7ec,
@@ -125,6 +164,16 @@ static u64 gisb_read_address(struct brcmstb_gisb_arb_device *gdev)
 	return value;
 }
 
+static u64 gisb_read_bp_address(struct brcmstb_gisb_arb_device *gdev)
+{
+	u64 value;
+
+	value = gisb_read(gdev, ARB_BP_CAP_ADDR);
+	value |= (u64)gisb_read(gdev, ARB_BP_CAP_HI_ADDR) << 32;
+
+	return value;
+}
+
 static void gisb_write(struct brcmstb_gisb_arb_device *gdev, u32 val, int reg)
 {
 	int offset = gdev->gisb_offsets[reg];
@@ -210,8 +259,8 @@ static int brcmstb_gisb_arb_decode_addr(struct brcmstb_gisb_arb_device *gdev,
 		m_name = m_fmt;
 	}
 
-	pr_crit("%s: %s at 0x%llx [%c %s], core: %s\n",
-		__func__, reason, arb_addr,
+	pr_crit("GISB: %s at 0x%llx [%c %s], core: %s\n",
+		reason, arb_addr,
 		cap_status & ARB_ERR_CAP_STATUS_WRITE ? 'W' : 'R',
 		cap_status & ARB_ERR_CAP_STATUS_TIMEOUT ? "timeout" : "",
 		m_name);
@@ -259,6 +308,41 @@ static irqreturn_t brcmstb_gisb_tea_handler(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+static irqreturn_t brcmstb_gisb_bp_handler(int irq, void *dev_id)
+{
+	struct brcmstb_gisb_arb_device *gdev = dev_id;
+	const char *m_name;
+	u32 bp_status;
+	u64 arb_addr;
+	u32 master;
+	char m_fmt[11];
+
+	bp_status = gisb_read(gdev, ARB_BP_CAP_STATUS);
+
+	/* Invalid captured address, bail out */
+	if (!(bp_status & ARB_BP_CAP_STATUS_VALID))
+		return IRQ_HANDLED;
+
+	/* Read the address and master */
+	arb_addr = gisb_read_bp_address(gdev);
+	master = gisb_read(gdev, ARB_BP_CAP_MASTER);
+
+	m_name = brcmstb_gisb_master_to_str(gdev, master);
+	if (!m_name) {
+		snprintf(m_fmt, sizeof(m_fmt), "0x%08x", master);
+		m_name = m_fmt;
+	}
+
+	pr_crit("GISB: breakpoint at 0x%llx [%c], core: %s\n",
+		arb_addr, bp_status & ARB_BP_CAP_STATUS_WRITE ? 'W' : 'R',
+		m_name);
+
+	/* clear the GISB error */
+	gisb_write(gdev, ARB_ERR_CAP_CLEAR, ARB_ERR_CAP_CLR);
+
+	return IRQ_HANDLED;
+}
+
 /*
  * Dump out gisb errors on die or panic.
  */
@@ -317,13 +401,14 @@ static int __init brcmstb_gisb_arb_probe(struct platform_device *pdev)
 	struct brcmstb_gisb_arb_device *gdev;
 	const struct of_device_id *of_id;
 	struct resource *r;
-	int err, timeout_irq, tea_irq;
+	int err, timeout_irq, tea_irq, bp_irq;
 	unsigned int num_masters, j = 0;
 	int i, first, last;
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	timeout_irq = platform_get_irq(pdev, 0);
 	tea_irq = platform_get_irq(pdev, 1);
+	bp_irq = platform_get_irq(pdev, 2);
 
 	gdev = devm_kzalloc(&pdev->dev, sizeof(*gdev), GFP_KERNEL);
 	if (!gdev)
@@ -356,6 +441,15 @@ static int __init brcmstb_gisb_arb_probe(struct platform_device *pdev)
 	if (err < 0)
 		return err;
 
+	/* Interrupt is optional */
+	if (bp_irq > 0) {
+		err = devm_request_irq(&pdev->dev, bp_irq,
+				       brcmstb_gisb_bp_handler, 0, pdev->name,
+				       gdev);
+		if (err < 0)
+			return err;
+	}
+
 	/* If we do not have a valid mask, assume all masters are enabled */
 	if (of_property_read_u32(dn, "brcm,gisb-arb-master-mask",
 				&gdev->valid_mask))

drivers/cpufreq/scmi-cpufreq.c

@@ -29,7 +29,7 @@ static const struct scmi_handle *handle;
 static unsigned int scmi_cpufreq_get_rate(unsigned int cpu)
 {
 	struct cpufreq_policy *policy = cpufreq_cpu_get_raw(cpu);
-	struct scmi_perf_ops *perf_ops = handle->perf_ops;
+	const struct scmi_perf_ops *perf_ops = handle->perf_ops;
 	struct scmi_data *priv = policy->driver_data;
 	unsigned long rate;
 	int ret;
@@ -49,7 +49,7 @@ static int
 scmi_cpufreq_set_target(struct cpufreq_policy *policy, unsigned int index)
 {
 	struct scmi_data *priv = policy->driver_data;
-	struct scmi_perf_ops *perf_ops = handle->perf_ops;
+	const struct scmi_perf_ops *perf_ops = handle->perf_ops;
 	u64 freq = policy->freq_table[index].frequency;
 
 	return perf_ops->freq_set(handle, priv->domain_id, freq * 1000, false);
@@ -59,7 +59,7 @@ static unsigned int scmi_cpufreq_fast_switch(struct cpufreq_policy *policy,
 					     unsigned int target_freq)
 {
 	struct scmi_data *priv = policy->driver_data;
-	struct scmi_perf_ops *perf_ops = handle->perf_ops;
+	const struct scmi_perf_ops *perf_ops = handle->perf_ops;
 
 	if (!perf_ops->freq_set(handle, priv->domain_id,
 				target_freq * 1000, true))

drivers/dma/ti/k3-udma-glue.c

@@ -573,8 +573,8 @@ static int k3_udma_glue_cfg_rx_flow(struct k3_udma_glue_rx_channel *rx_chn,
 
 	/* request and cfg rings */
 	ret =  k3_ringacc_request_rings_pair(rx_chn->common.ringacc,
-					     flow_cfg->ring_rxq_id,
 					     flow_cfg->ring_rxfdq0_id,
+					     flow_cfg->ring_rxq_id,
 					     &flow->ringrxfdq,
 					     &flow->ringrx);
 	if (ret) {

drivers/firmware/Kconfig

@@ -7,7 +7,7 @@
 menu "Firmware Drivers"
 
 config ARM_SCMI_PROTOCOL
-	bool "ARM System Control and Management Interface (SCMI) Message Protocol"
+	tristate "ARM System Control and Management Interface (SCMI) Message Protocol"
 	depends on ARM || ARM64 || COMPILE_TEST
 	depends on MAILBOX
 	help

drivers/firmware/Makefile

@@ -22,7 +22,7 @@ obj-$(CONFIG_TI_SCI_PROTOCOL)	+= ti_sci.o
 obj-$(CONFIG_TRUSTED_FOUNDATIONS) += trusted_foundations.o
 obj-$(CONFIG_TURRIS_MOX_RWTM)	+= turris-mox-rwtm.o
 
-obj-$(CONFIG_ARM_SCMI_PROTOCOL)	+= arm_scmi/
+obj-y				+= arm_scmi/
 obj-y				+= broadcom/
 obj-y				+= meson/
 obj-$(CONFIG_GOOGLE_FIRMWARE)	+= google/

drivers/firmware/arm_scmi/Makefile

 # SPDX-License-Identifier: GPL-2.0-only
-obj-y	= scmi-bus.o scmi-driver.o scmi-protocols.o scmi-transport.o
 scmi-bus-y = bus.o
 scmi-driver-y = driver.o notify.o
 scmi-transport-y = shmem.o
 scmi-transport-$(CONFIG_MAILBOX) += mailbox.o
 scmi-transport-$(CONFIG_HAVE_ARM_SMCCC_DISCOVERY) += smc.o
-scmi-protocols-y = base.o clock.o perf.o power.o reset.o sensors.o
+scmi-protocols-y = base.o clock.o perf.o power.o reset.o sensors.o system.o
+scmi-module-objs := $(scmi-bus-y) $(scmi-driver-y) $(scmi-protocols-y) \
+		    $(scmi-transport-y)
+obj-$(CONFIG_ARM_SCMI_PROTOCOL) += scmi-module.o
 obj-$(CONFIG_ARM_SCMI_POWER_DOMAIN) += scmi_pm_domain.o

drivers/firmware/arm_scmi/bus.c

@@ -230,7 +230,7 @@ static void scmi_devices_unregister(void)
 	bus_for_each_dev(&scmi_bus_type, NULL, NULL, __scmi_devices_unregister);
 }
 
-static int __init scmi_bus_init(void)
+int __init scmi_bus_init(void)
 {
 	int retval;
 
@@ -240,12 +240,10 @@ static int __init scmi_bus_init(void)
 
 	return retval;
 }
-subsys_initcall(scmi_bus_init);
 
-static void __exit scmi_bus_exit(void)
+void __exit scmi_bus_exit(void)
 {
 	scmi_devices_unregister();
 	bus_unregister(&scmi_bus_type);
 	ida_destroy(&scmi_bus_id);
 }
-module_exit(scmi_bus_exit);

drivers/firmware/arm_scmi/clock.c

@@ -318,7 +318,7 @@ scmi_clock_info_get(const struct scmi_handle *handle, u32 clk_id)
 	return clk;
 }
 
-static struct scmi_clk_ops clk_ops = {
+static const struct scmi_clk_ops clk_ops = {
 	.count_get = scmi_clock_count_get,
 	.info_get = scmi_clock_info_get,
 	.rate_get = scmi_clock_rate_get,
@@ -364,9 +364,4 @@ static int scmi_clock_protocol_init(struct scmi_handle *handle)
 	return 0;
 }
 
-static int __init scmi_clock_init(void)
-{
-	return scmi_protocol_register(SCMI_PROTOCOL_CLOCK,
-				      &scmi_clock_protocol_init);
-}
-subsys_initcall(scmi_clock_init);
+DEFINE_SCMI_PROTOCOL_REGISTER_UNREGISTER(SCMI_PROTOCOL_CLOCK, clock)

drivers/firmware/arm_scmi/common.h

@@ -156,6 +156,30 @@ void scmi_setup_protocol_implemented(const struct scmi_handle *handle,
 
 int scmi_base_protocol_init(struct scmi_handle *h);
 
+int __init scmi_bus_init(void);
+void __exit scmi_bus_exit(void);
+
+#define DECLARE_SCMI_REGISTER_UNREGISTER(func)		\
+	int __init scmi_##func##_register(void);	\
+	void __exit scmi_##func##_unregister(void)
+DECLARE_SCMI_REGISTER_UNREGISTER(clock);
+DECLARE_SCMI_REGISTER_UNREGISTER(perf);
+DECLARE_SCMI_REGISTER_UNREGISTER(power);
+DECLARE_SCMI_REGISTER_UNREGISTER(reset);
+DECLARE_SCMI_REGISTER_UNREGISTER(sensors);
+DECLARE_SCMI_REGISTER_UNREGISTER(system);
+
+#define DEFINE_SCMI_PROTOCOL_REGISTER_UNREGISTER(id, name) \
+int __init scmi_##name##_register(void) \
+{ \
+	return scmi_protocol_register((id), &scmi_##name##_protocol_init); \
+} \
+\
+void __exit scmi_##name##_unregister(void) \
+{ \
+	scmi_protocol_unregister((id)); \
+}
+
 /* SCMI Transport */
 /**
  * struct scmi_chan_info - Structure representing a SCMI channel information
@@ -210,7 +234,7 @@ struct scmi_transport_ops {
  * @max_msg_size: Maximum size of data per message that can be handled.
  */
 struct scmi_desc {
-	struct scmi_transport_ops *ops;
+	const struct scmi_transport_ops *ops;
 	int max_rx_timeout_ms;
 	int max_msg;
 	int max_msg_size;

drivers/firmware/arm_scmi/driver.c

@@ -730,6 +730,7 @@ struct scmi_prot_devnames {
 
 static struct scmi_prot_devnames devnames[] = {
 	{ SCMI_PROTOCOL_POWER,  { "genpd" },},
+	{ SCMI_PROTOCOL_SYSTEM, { "syspower" },},
 	{ SCMI_PROTOCOL_PERF,   { "cpufreq" },},
 	{ SCMI_PROTOCOL_CLOCK,  { "clocks" },},
 	{ SCMI_PROTOCOL_SENSOR, { "hwmon" },},
@@ -928,7 +929,35 @@ static struct platform_driver scmi_driver = {
 	.remove = scmi_remove,
 };
 
-module_platform_driver(scmi_driver);
+static int __init scmi_driver_init(void)
+{
+	scmi_bus_init();
+
+	scmi_clock_register();
+	scmi_perf_register();
+	scmi_power_register();
+	scmi_reset_register();
+	scmi_sensors_register();
+	scmi_system_register();
+
+	return platform_driver_register(&scmi_driver);
+}
+subsys_initcall(scmi_driver_init);
+
+static void __exit scmi_driver_exit(void)
+{
+	scmi_bus_exit();
+
+	scmi_clock_unregister();
+	scmi_perf_unregister();
+	scmi_power_unregister();
+	scmi_reset_unregister();
+	scmi_sensors_unregister();
+	scmi_system_unregister();
+
+	platform_driver_unregister(&scmi_driver);
+}
+module_exit(scmi_driver_exit);
 
 MODULE_ALIAS("platform: arm-scmi");
 MODULE_AUTHOR("Sudeep Holla <sudeep.holla@arm.com>");

drivers/firmware/arm_scmi/mailbox.c

@@ -110,7 +110,7 @@ static int mailbox_chan_free(int id, void *p, void *data)
 	struct scmi_chan_info *cinfo = p;
 	struct scmi_mailbox *smbox = cinfo->transport_info;
 
-	if (!IS_ERR(smbox->chan)) {
+	if (smbox && !IS_ERR(smbox->chan)) {
 		mbox_free_channel(smbox->chan);
 		cinfo->transport_info = NULL;
 		smbox->chan = NULL;
@@ -181,7 +181,7 @@ mailbox_poll_done(struct scmi_chan_info *cinfo, struct scmi_xfer *xfer)
 	return shmem_poll_done(smbox->shmem, xfer);
 }
 
-static struct scmi_transport_ops scmi_mailbox_ops = {
+static const struct scmi_transport_ops scmi_mailbox_ops = {
 	.chan_available = mailbox_chan_available,
 	.chan_setup = mailbox_chan_setup,
 	.chan_free = mailbox_chan_free,

drivers/firmware/arm_scmi/notify.c

@@ -1421,7 +1421,7 @@ static void scmi_protocols_late_init(struct work_struct *work)
  * notify_ops are attached to the handle so that can be accessed
  * directly from an scmi_driver to register its own notifiers.
  */
-static struct scmi_notify_ops notify_ops = {
+static const struct scmi_notify_ops notify_ops = {
 	.register_event_notifier = scmi_register_notifier,
 	.unregister_event_notifier = scmi_unregister_notifier,
 };

drivers/firmware/arm_scmi/perf.c

@@ -748,7 +748,7 @@ static bool scmi_fast_switch_possible(const struct scmi_handle *handle,
 	return dom->fc_info && dom->fc_info->level_set_addr;
 }
 
-static struct scmi_perf_ops perf_ops = {
+static const struct scmi_perf_ops perf_ops = {
 	.limits_set = scmi_perf_limits_set,
 	.limits_get = scmi_perf_limits_get,
 	.level_set = scmi_perf_level_set,
@@ -890,9 +890,4 @@ static int scmi_perf_protocol_init(struct scmi_handle *handle)
 	return 0;
 }
 
-static int __init scmi_perf_init(void)
-{
-	return scmi_protocol_register(SCMI_PROTOCOL_PERF,
-				      &scmi_perf_protocol_init);
-}
-subsys_initcall(scmi_perf_init);
+DEFINE_SCMI_PROTOCOL_REGISTER_UNREGISTER(SCMI_PROTOCOL_PERF, perf)

drivers/firmware/arm_scmi/power.c

@@ -184,7 +184,7 @@ static char *scmi_power_name_get(const struct scmi_handle *handle, u32 domain)
 	return dom->name;
 }
 
-static struct scmi_power_ops power_ops = {
+static const struct scmi_power_ops power_ops = {
 	.num_domains_get = scmi_power_num_domains_get,
 	.name_get = scmi_power_name_get,
 	.state_set = scmi_power_state_set,
@@ -301,9 +301,4 @@ static int scmi_power_protocol_init(struct scmi_handle *handle)
 	return 0;
 }
 
-static int __init scmi_power_init(void)
-{
-	return scmi_protocol_register(SCMI_PROTOCOL_POWER,
-				      &scmi_power_protocol_init);
-}
-subsys_initcall(scmi_power_init);
+DEFINE_SCMI_PROTOCOL_REGISTER_UNREGISTER(SCMI_PROTOCOL_POWER, power)

drivers/firmware/arm_scmi/reset.c

@@ -194,7 +194,7 @@ scmi_reset_domain_deassert(const struct scmi_handle *handle, u32 domain)
 	return scmi_domain_reset(handle, domain, 0, ARCH_COLD_RESET);
 }
 
-static struct scmi_reset_ops reset_ops = {
+static const struct scmi_reset_ops reset_ops = {
 	.num_domains_get = scmi_reset_num_domains_get,
 	.name_get = scmi_reset_name_get,
 	.latency_get = scmi_reset_latency_get,
@@ -313,9 +313,4 @@ static int scmi_reset_protocol_init(struct scmi_handle *handle)
 	return 0;
 }
 
-static int __init scmi_reset_init(void)
-{
-	return scmi_protocol_register(SCMI_PROTOCOL_RESET,
-				      &scmi_reset_protocol_init);
-}
-subsys_initcall(scmi_reset_init);
+DEFINE_SCMI_PROTOCOL_REGISTER_UNREGISTER(SCMI_PROTOCOL_RESET, reset)

drivers/firmware/arm_scmi/sensors.c

@@ -275,7 +275,7 @@ static int scmi_sensor_count_get(const struct scmi_handle *handle)
 	return si->num_sensors;
 }
 
-static struct scmi_sensor_ops sensor_ops = {
+static const struct scmi_sensor_ops sensor_ops = {
 	.count_get = scmi_sensor_count_get,
 	.info_get = scmi_sensor_info_get,
 	.trip_point_config = scmi_sensor_trip_point_config,
@@ -365,9 +365,4 @@ static int scmi_sensors_protocol_init(struct scmi_handle *handle)
 	return 0;
 }
 
-static int __init scmi_sensors_init(void)
-{
-	return scmi_protocol_register(SCMI_PROTOCOL_SENSOR,
-				      &scmi_sensors_protocol_init);
-}
-subsys_initcall(scmi_sensors_init);
+DEFINE_SCMI_PROTOCOL_REGISTER_UNREGISTER(SCMI_PROTOCOL_SENSOR, sensors)

drivers/firmware/arm_scmi/smc.c

@@ -137,7 +137,7 @@ smc_poll_done(struct scmi_chan_info *cinfo, struct scmi_xfer *xfer)
 	return shmem_poll_done(scmi_info->shmem, xfer);
 }
 
-static struct scmi_transport_ops scmi_smc_ops = {
+static const struct scmi_transport_ops scmi_smc_ops = {
 	.chan_available = smc_chan_available,
 	.chan_setup = smc_chan_setup,
 	.chan_free = smc_chan_free,

drivers/firmware/arm_scmi/system.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * System Control and Management Interface (SCMI) System Power Protocol
+ *
+ * Copyright (C) 2020 ARM Ltd.
+ */
+
+#define pr_fmt(fmt) "SCMI Notifications SYSTEM - " fmt
+
+#include <linux/scmi_protocol.h>
+
+#include "common.h"
+#include "notify.h"
+
+#define SCMI_SYSTEM_NUM_SOURCES		1
+
+enum scmi_system_protocol_cmd {
+	SYSTEM_POWER_STATE_NOTIFY = 0x5,
+};
+
+struct scmi_system_power_state_notify {
+	__le32 notify_enable;
+};
+
+struct scmi_system_power_state_notifier_payld {
+	__le32 agent_id;
+	__le32 flags;
+	__le32 system_state;
+};
+
+struct scmi_system_info {
+	u32 version;
+};
+
+static int scmi_system_request_notify(const struct scmi_handle *handle,
+				      bool enable)
+{
+	int ret;
+	struct scmi_xfer *t;
+	struct scmi_system_power_state_notify *notify;
+
+	ret = scmi_xfer_get_init(handle, SYSTEM_POWER_STATE_NOTIFY,
+				 SCMI_PROTOCOL_SYSTEM, sizeof(*notify), 0, &t);
+	if (ret)
+		return ret;
+
+	notify = t->tx.buf;
+	notify->notify_enable = enable ? cpu_to_le32(BIT(0)) : 0;
+
+	ret = scmi_do_xfer(handle, t);
+
+	scmi_xfer_put(handle, t);
+	return ret;
+}
+
+static int scmi_system_set_notify_enabled(const struct scmi_handle *handle,
+					  u8 evt_id, u32 src_id, bool enable)
+{
+	int ret;
+
+	ret = scmi_system_request_notify(handle, enable);
+	if (ret)
+		pr_debug("FAIL_ENABLE - evt[%X] - ret:%d\n", evt_id, ret);
+
+	return ret;
+}
+
+static void *scmi_system_fill_custom_report(const struct scmi_handle *handle,
+					    u8 evt_id, ktime_t timestamp,
+					    const void *payld, size_t payld_sz,
+					    void *report, u32 *src_id)
+{
+	const struct scmi_system_power_state_notifier_payld *p = payld;
+	struct scmi_system_power_state_notifier_report *r = report;
+
+	if (evt_id != SCMI_EVENT_SYSTEM_POWER_STATE_NOTIFIER ||
+	    sizeof(*p) != payld_sz)
+		return NULL;
+
+	r->timestamp = timestamp;
+	r->agent_id = le32_to_cpu(p->agent_id);
+	r->flags = le32_to_cpu(p->flags);
+	r->system_state = le32_to_cpu(p->system_state);
+	*src_id = 0;
+
+	return r;
+}
+
+static const struct scmi_event system_events[] = {
+	{
+		.id = SCMI_EVENT_SYSTEM_POWER_STATE_NOTIFIER,
+		.max_payld_sz =
+			sizeof(struct scmi_system_power_state_notifier_payld),
+		.max_report_sz =
+			sizeof(struct scmi_system_power_state_notifier_report),
+	},
+};
+
+static const struct scmi_event_ops system_event_ops = {
+	.set_notify_enabled = scmi_system_set_notify_enabled,
+	.fill_custom_report = scmi_system_fill_custom_report,
+};
+
+static int scmi_system_protocol_init(struct scmi_handle *handle)
+{
+	u32 version;
+	struct scmi_system_info *pinfo;
+
+	scmi_version_get(handle, SCMI_PROTOCOL_SYSTEM, &version);
+
+	dev_dbg(handle->dev, "System Power Version %d.%d\n",
+		PROTOCOL_REV_MAJOR(version), PROTOCOL_REV_MINOR(version));
+
+	pinfo = devm_kzalloc(handle->dev, sizeof(*pinfo), GFP_KERNEL);
+	if (!pinfo)
+		return -ENOMEM;
+
+	scmi_register_protocol_events(handle,
+				      SCMI_PROTOCOL_SYSTEM, SCMI_PROTO_QUEUE_SZ,
+				      &system_event_ops,
+				      system_events,
+				      ARRAY_SIZE(system_events),
+				      SCMI_SYSTEM_NUM_SOURCES);
+
+	pinfo->version = version;
+	handle->system_priv = pinfo;
+
+	return 0;
+}
+
+DEFINE_SCMI_PROTOCOL_REGISTER_UNREGISTER(SCMI_PROTOCOL_SYSTEM, system)

drivers/firmware/imx/scu-pd.c

@@ -46,6 +46,7 @@
 
 #include <dt-bindings/firmware/imx/rsrc.h>
 #include <linux/firmware/imx/sci.h>
+#include <linux/firmware/imx/svc/rm.h>
 #include <linux/io.h>
 #include <linux/module.h>
 #include <linux/of.h>
@@ -256,6 +257,9 @@ imx_scu_add_pm_domain(struct device *dev, int idx,
 	struct imx_sc_pm_domain *sc_pd;
 	int ret;
 
+	if (!imx_sc_rm_is_resource_owned(pm_ipc_handle, pd_ranges->rsrc + idx))
+		return NULL;
+
 	sc_pd = devm_kzalloc(dev, sizeof(*sc_pd), GFP_KERNEL);
 	if (!sc_pd)
 		return ERR_PTR(-ENOMEM);

drivers/firmware/smccc/smccc.c

@@ -24,8 +24,10 @@ enum arm_smccc_conduit arm_smccc_1_1_get_conduit(void)
 
 	return smccc_conduit;
 }
+EXPORT_SYMBOL_GPL(arm_smccc_1_1_get_conduit);
 
 u32 arm_smccc_get_version(void)
 {
 	return smccc_version;
 }
+EXPORT_SYMBOL_GPL(arm_smccc_get_version);

drivers/firmware/tegra/bpmp.c

@@ -856,7 +856,8 @@ static const struct tegra_bpmp_soc tegra210_soc = {
 
 static const struct of_device_id tegra_bpmp_match[] = {
 #if IS_ENABLED(CONFIG_ARCH_TEGRA_186_SOC) || \
-    IS_ENABLED(CONFIG_ARCH_TEGRA_194_SOC)
+    IS_ENABLED(CONFIG_ARCH_TEGRA_194_SOC) || \
+    IS_ENABLED(CONFIG_ARCH_TEGRA_234_SOC)
 	{ .compatible = "nvidia,tegra186-bpmp", .data = &tegra186_soc },
 #endif
 #if IS_ENABLED(CONFIG_ARCH_TEGRA_210_SOC)

drivers/firmware/ti_sci.c

@@ -1106,7 +1106,8 @@ static int ti_sci_cmd_get_clock(const struct ti_sci_handle *handle, u32 dev_id,
 static int ti_sci_cmd_idle_clock(const struct ti_sci_handle *handle,
 				 u32 dev_id, u32 clk_id)
 {
-	return ti_sci_set_clock_state(handle, dev_id, clk_id, 0,
+	return ti_sci_set_clock_state(handle, dev_id, clk_id,
+				      MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE,
 				      MSG_CLOCK_SW_STATE_UNREQ);
 }
 
@@ -1125,7 +1126,8 @@ static int ti_sci_cmd_idle_clock(const struct ti_sci_handle *handle,
 static int ti_sci_cmd_put_clock(const struct ti_sci_handle *handle,
 				u32 dev_id, u32 clk_id)
 {
-	return ti_sci_set_clock_state(handle, dev_id, clk_id, 0,
+	return ti_sci_set_clock_state(handle, dev_id, clk_id,
+				      MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE,
 				      MSG_CLOCK_SW_STATE_AUTO);
 }
 

drivers/gpu/drm/mediatek/mtk_drm_crtc.c

@@ -481,7 +481,7 @@ static void mtk_drm_crtc_hw_config(struct mtk_drm_crtc *mtk_crtc)
 		mbox_flush(mtk_crtc->cmdq_client->chan, 2000);
 		cmdq_handle = cmdq_pkt_create(mtk_crtc->cmdq_client, PAGE_SIZE);
 		cmdq_pkt_clear_event(cmdq_handle, mtk_crtc->cmdq_event);
-		cmdq_pkt_wfe(cmdq_handle, mtk_crtc->cmdq_event);
+		cmdq_pkt_wfe(cmdq_handle, mtk_crtc->cmdq_event, false);
 		mtk_crtc_ddp_config(crtc, cmdq_handle);
 		cmdq_pkt_finalize(cmdq_handle);
 		cmdq_pkt_flush_async(cmdq_handle, ddp_cmdq_cb, cmdq_handle);

drivers/mailbox/tegra-hsp.c

@@ -13,6 +13,8 @@
 #include <linux/pm.h>
 #include <linux/slab.h>
 
+#include <soc/tegra/fuse.h>
+
 #include <dt-bindings/mailbox/tegra186-hsp.h>
 
 #include "mailbox.h"
@@ -322,7 +324,12 @@ static int tegra_hsp_doorbell_startup(struct mbox_chan *chan)
 	if (!ccplex)
 		return -ENODEV;
 
-	if (!tegra_hsp_doorbell_can_ring(db))
+	/*
+	 * On simulation platforms the BPMP hasn't had a chance yet to mark
+	 * the doorbell as ringable by the CCPLEX, so we want to skip extra
+	 * checks here.
+	 */
+	if (tegra_is_silicon() && !tegra_hsp_doorbell_can_ring(db))
 		return -ENODEV;
 
 	spin_lock_irqsave(&hsp->lock, flags);

drivers/memory/Kconfig

@@ -32,8 +32,9 @@ config ARM_PL172_MPMC
 
 config ATMEL_SDRAMC
 	bool "Atmel (Multi-port DDR-)SDRAM Controller"
-	default y
-	depends on ARCH_AT91 && OF
+	default y if ARCH_AT91
+	depends on ARCH_AT91 || COMPILE_TEST
+	depends on OF
 	help
 	  This driver is for Atmel SDRAM Controller or Atmel Multi-port
 	  DDR-SDRAM Controller available on Atmel AT91SAM9 and SAMA5 SoCs.
@@ -42,8 +43,9 @@ config ATMEL_SDRAMC
 
 config ATMEL_EBI
 	bool "Atmel EBI driver"
-	default y
-	depends on ARCH_AT91 && OF
+	default y if ARCH_AT91
+	depends on ARCH_AT91 || COMPILE_TEST
+	depends on OF
 	select MFD_SYSCON
 	select MFD_ATMEL_SMC
 	help
@@ -52,6 +54,18 @@ config ATMEL_EBI
 	  tree is used. This bus supports NANDs, external ethernet controller,
 	  SRAMs, ATA devices, etc.
 
+config BRCMSTB_DPFE
+	bool "Broadcom STB DPFE driver" if COMPILE_TEST
+	default y if ARCH_BRCMSTB
+	depends on ARCH_BRCMSTB || COMPILE_TEST
+	help
+	  This driver provides access to the DPFE interface of Broadcom
+	  STB SoCs. The firmware running on the DCPU inside the DDR PHY can
+	  provide current information about the system's RAM, for instance
+	  the DRAM refresh rate. This can be used as an indirect indicator
+	  for the DRAM's temperature. Slower refresh rate means cooler RAM,
+	  higher refresh rate means hotter RAM.
+
 config BT1_L2_CTL
 	bool "Baikal-T1 CM2 L2-RAM Cache Control Block"
 	depends on MIPS_BAIKAL_T1 || COMPILE_TEST
@@ -65,7 +79,8 @@ config BT1_L2_CTL
 
 config TI_AEMIF
 	tristate "Texas Instruments AEMIF driver"
-	depends on (ARCH_DAVINCI || ARCH_KEYSTONE) && OF
+	depends on ARCH_DAVINCI || ARCH_KEYSTONE || COMPILE_TEST
+	depends on OF
 	help
 	  This driver is for the AEMIF module available in Texas Instruments
 	  SoCs. AEMIF stands for Asynchronous External Memory Interface and
@@ -76,7 +91,7 @@ config TI_AEMIF
 
 config TI_EMIF
 	tristate "Texas Instruments EMIF driver"
-	depends on ARCH_OMAP2PLUS
+	depends on ARCH_OMAP2PLUS || COMPILE_TEST
 	select DDR
 	help
 	  This driver is for the EMIF module available in Texas Instruments
@@ -88,7 +103,8 @@ config TI_EMIF
 	  temperature changes
 
 config OMAP_GPMC
-	bool
+	bool "Texas Instruments OMAP SoC GPMC driver" if COMPILE_TEST
+	depends on OF_ADDRESS
 	select GPIOLIB
 	help
 	  This driver is for the General Purpose Memory Controller (GPMC)
@@ -112,7 +128,8 @@ config OMAP_GPMC_DEBUG
 
 config TI_EMIF_SRAM
 	tristate "Texas Instruments EMIF SRAM driver"
-	depends on (SOC_AM33XX || SOC_AM43XX) && SRAM
+	depends on SOC_AM33XX || SOC_AM43XX || (ARM && COMPILE_TEST)
+	depends on SRAM
 	help
 	  This driver is for the EMIF module available on Texas Instruments
 	  AM33XX and AM43XX SoCs and is required for PM. Certain parts of
@@ -122,8 +139,9 @@ config TI_EMIF_SRAM
 
 config MVEBU_DEVBUS
 	bool "Marvell EBU Device Bus Controller"
-	default y
-	depends on PLAT_ORION && OF
+	default y if PLAT_ORION
+	depends on PLAT_ORION || COMPILE_TEST
+	depends on OF
 	help
 	  This driver is for the Device Bus controller available in some
 	  Marvell EBU SoCs such as Discovery (mv78xx0), Orion (88f5xxx) and
@@ -132,7 +150,7 @@ config MVEBU_DEVBUS
 
 config FSL_CORENET_CF
 	tristate "Freescale CoreNet Error Reporting"
-	depends on FSL_SOC_BOOKE
+	depends on FSL_SOC_BOOKE || COMPILE_TEST
 	help
 	  Say Y for reporting of errors from the Freescale CoreNet
 	  Coherency Fabric.  Errors reported include accesses to
@@ -141,7 +159,7 @@ config FSL_CORENET_CF
 	  represents a coherency violation.
 
 config FSL_IFC
-	bool
+	bool "Freescale IFC driver" if COMPILE_TEST
 	depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A || COMPILE_TEST
 	depends on HAS_IOMEM
 
@@ -155,7 +173,7 @@ config JZ4780_NEMC
 	  memory devices such as NAND and SRAM.
 
 config MTK_SMI
-	bool
+	bool "Mediatek SoC Memory Controller driver" if COMPILE_TEST
 	depends on ARCH_MEDIATEK || COMPILE_TEST
 	help
 	  This driver is for the Memory Controller module in MediaTek SoCs,
@@ -164,7 +182,7 @@ config MTK_SMI
 
 config DA8XX_DDRCTL
 	bool "Texas Instruments da8xx DDR2/mDDR driver"
-	depends on ARCH_DAVINCI_DA8XX
+	depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST
 	help
 	  This driver is for the DDR2/mDDR Memory Controller present on
 	  Texas Instruments da8xx SoCs. It's used to tweak various memory
@@ -172,16 +190,16 @@ config DA8XX_DDRCTL
 
 config PL353_SMC
 	tristate "ARM PL35X Static Memory Controller(SMC) driver"
-	default y
+	default y if ARM
 	depends on ARM
-	depends on ARM_AMBA
+	depends on ARM_AMBA || COMPILE_TEST
 	help
 	  This driver is for the ARM PL351/PL353 Static Memory
 	  Controller(SMC) module.
 
 config RENESAS_RPCIF
 	tristate "Renesas RPC-IF driver"
-	depends on ARCH_RENESAS
+	depends on ARCH_RENESAS || COMPILE_TEST
 	select REGMAP_MMIO
 	help
 	  This supports Renesas R-Car Gen3 RPC-IF which provides either SPI

drivers/memory/Makefile

@@ -10,7 +10,7 @@ endif
 obj-$(CONFIG_ARM_PL172_MPMC)	+= pl172.o
 obj-$(CONFIG_ATMEL_SDRAMC)	+= atmel-sdramc.o
 obj-$(CONFIG_ATMEL_EBI)		+= atmel-ebi.o
-obj-$(CONFIG_ARCH_BRCMSTB)	+= brcmstb_dpfe.o
+obj-$(CONFIG_BRCMSTB_DPFE)	+= brcmstb_dpfe.o
 obj-$(CONFIG_BT1_L2_CTL)	+= bt1-l2-ctl.o
 obj-$(CONFIG_TI_AEMIF)		+= ti-aemif.o
 obj-$(CONFIG_TI_EMIF)		+= emif.o

drivers/memory/brcmstb_dpfe.c

@@ -188,11 +188,6 @@ struct brcmstb_dpfe_priv {
 	struct mutex lock;
 };
 
-static const char * const error_text[] = {
-	"Success", "Header code incorrect", "Unknown command or argument",
-	"Incorrect checksum", "Malformed command", "Timed out",
-};
-
 /*
  * Forward declaration of our sysfs attribute functions, so we can declare the
  * attribute data structures early.
@@ -307,6 +302,20 @@ static const struct dpfe_api dpfe_api_v3 = {
 	},
 };
 
+static const char *get_error_text(unsigned int i)
+{
+	static const char * const error_text[] = {
+		"Success", "Header code incorrect",
+		"Unknown command or argument", "Incorrect checksum",
+		"Malformed command", "Timed out", "Unknown error",
+	};
+
+	if (unlikely(i >= ARRAY_SIZE(error_text)))
+		i = ARRAY_SIZE(error_text) - 1;
+
+	return error_text[i];
+}
+
 static bool is_dcpu_enabled(struct brcmstb_dpfe_priv *priv)
 {
 	u32 val;
@@ -445,7 +454,7 @@ static int __send_command(struct brcmstb_dpfe_priv *priv, unsigned int cmd,
 	}
 	if (resp != 0) {
 		mutex_unlock(&priv->lock);
-		return -ETIMEDOUT;
+		return -ffs(DCPU_RET_ERR_TIMEDOUT);
 	}
 
 	/* Compute checksum over the message */
@@ -647,8 +656,10 @@ static int brcmstb_dpfe_download_firmware(struct brcmstb_dpfe_priv *priv)
 		return (ret == -ENOENT) ? -EPROBE_DEFER : ret;
 
 	ret = __verify_firmware(&init, fw);
-	if (ret)
-		return -EFAULT;
+	if (ret) {
+		ret = -EFAULT;
+		goto release_fw;
+	}
 
 	__disable_dcpu(priv);
 
@@ -667,18 +678,20 @@ static int brcmstb_dpfe_download_firmware(struct brcmstb_dpfe_priv *priv)
 
 	ret = __write_firmware(priv->dmem, dmem, dmem_size, is_big_endian);
 	if (ret)
-		return ret;
+		goto release_fw;
 	ret = __write_firmware(priv->imem, imem, imem_size, is_big_endian);
 	if (ret)
-		return ret;
+		goto release_fw;
 
 	ret = __verify_fw_checksum(&init, priv, header, init.chksum);
 	if (ret)
-		return ret;
+		goto release_fw;
 
 	__enable_dcpu(priv);
 
-	return 0;
+release_fw:
+	release_firmware(fw);
+	return ret;
 }
 
 static ssize_t generic_show(unsigned int command, u32 response[],
@@ -691,7 +704,7 @@ static ssize_t generic_show(unsigned int command, u32 response[],
 
 	ret = __send_command(priv, command, response);
 	if (ret < 0)
-		return sprintf(buf, "ERROR: %s\n", error_text[-ret]);
+		return sprintf(buf, "ERROR: %s\n", get_error_text(-ret));
 
 	return 0;
 }
@@ -888,11 +901,8 @@ static int brcmstb_dpfe_probe(struct platform_device *pdev)
 	}
 
 	ret = brcmstb_dpfe_download_firmware(priv);
-	if (ret) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "Couldn't download firmware -- %d\n", ret);
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(dev, ret, "Couldn't download firmware\n");
 
 	ret = sysfs_create_groups(&pdev->dev.kobj, priv->dpfe_api->sysfs_attrs);
 	if (!ret)

drivers/memory/emif.c

@@ -131,16 +131,7 @@ static int emif_regdump_show(struct seq_file *s, void *unused)
 	return 0;
 }
 
-static int emif_regdump_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, emif_regdump_show, inode->i_private);
-}
-
-static const struct file_operations emif_regdump_fops = {
-	.open			= emif_regdump_open,
-	.read			= seq_read,
-	.release		= single_release,
-};
+DEFINE_SHOW_ATTRIBUTE(emif_regdump);
 
 static int emif_mr4_show(struct seq_file *s, void *unused)
 {
@@ -150,48 +141,16 @@ static int emif_mr4_show(struct seq_file *s, void *unused)
 	return 0;
 }
 
-static int emif_mr4_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, emif_mr4_show, inode->i_private);
-}
-
-static const struct file_operations emif_mr4_fops = {
-	.open			= emif_mr4_open,
-	.read			= seq_read,
-	.release		= single_release,
-};
+DEFINE_SHOW_ATTRIBUTE(emif_mr4);
 
 static int __init_or_module emif_debugfs_init(struct emif_data *emif)
 {
-	struct dentry	*dentry;
-	int		ret;
-
-	dentry = debugfs_create_dir(dev_name(emif->dev), NULL);
-	if (!dentry) {
-		ret = -ENOMEM;
-		goto err0;
-	}
-	emif->debugfs_root = dentry;
-
-	dentry = debugfs_create_file("regcache_dump", S_IRUGO,
-			emif->debugfs_root, emif, &emif_regdump_fops);
-	if (!dentry) {
-		ret = -ENOMEM;
-		goto err1;
-	}
-
-	dentry = debugfs_create_file("mr4", S_IRUGO,
-			emif->debugfs_root, emif, &emif_mr4_fops);
-	if (!dentry) {
-		ret = -ENOMEM;
-		goto err1;
-	}
-
+	emif->debugfs_root = debugfs_create_dir(dev_name(emif->dev), NULL);
+	debugfs_create_file("regcache_dump", S_IRUGO, emif->debugfs_root, emif,
+			    &emif_regdump_fops);
+	debugfs_create_file("mr4", S_IRUGO, emif->debugfs_root, emif,
+			    &emif_mr4_fops);
 	return 0;
-err1:
-	debugfs_remove_recursive(emif->debugfs_root);
-err0:
-	return ret;
 }
 
 static void __exit emif_debugfs_exit(struct emif_data *emif)

drivers/memory/fsl-corenet-cf.c

@@ -211,10 +211,8 @@ static int ccf_probe(struct platform_device *pdev)
 	dev_set_drvdata(&pdev->dev, ccf);
 
 	irq = platform_get_irq(pdev, 0);
-	if (!irq) {
-		dev_err(&pdev->dev, "%s: no irq\n", __func__);
-		return -ENXIO;
-	}
+	if (irq < 0)
+		return irq;
 
 	ret = devm_request_irq(&pdev->dev, irq, ccf_irq, 0, pdev->name, ccf);
 	if (ret) {

drivers/memory/mtk-smi.c

@@ -19,6 +19,9 @@
 /* mt8173 */
 #define SMI_LARB_MMU_EN		0xf00
 
+/* mt8167 */
+#define MT8167_SMI_LARB_MMU_EN	0xfc0
+
 /* mt2701 */
 #define REG_SMI_SECUR_CON_BASE		0x5c0
 
@@ -179,6 +182,13 @@ static void mtk_smi_larb_config_port_mt8173(struct device *dev)
 	writel(*larb->mmu, larb->base + SMI_LARB_MMU_EN);
 }
 
+static void mtk_smi_larb_config_port_mt8167(struct device *dev)
+{
+	struct mtk_smi_larb *larb = dev_get_drvdata(dev);
+
+	writel(*larb->mmu, larb->base + MT8167_SMI_LARB_MMU_EN);
+}
+
 static void mtk_smi_larb_config_port_gen1(struct device *dev)
 {
 	struct mtk_smi_larb *larb = dev_get_drvdata(dev);
@@ -226,6 +236,11 @@ static const struct mtk_smi_larb_gen mtk_smi_larb_mt8173 = {
 	.config_port = mtk_smi_larb_config_port_mt8173,
 };
 
+static const struct mtk_smi_larb_gen mtk_smi_larb_mt8167 = {
+	/* mt8167 do not need the port in larb */
+	.config_port = mtk_smi_larb_config_port_mt8167,
+};
+
 static const struct mtk_smi_larb_gen mtk_smi_larb_mt2701 = {
 	.port_in_larb = {
 		LARB0_PORT_OFFSET, LARB1_PORT_OFFSET,
@@ -254,6 +269,10 @@ static const struct mtk_smi_larb_gen mtk_smi_larb_mt8183 = {
 };
 
 static const struct of_device_id mtk_smi_larb_of_ids[] = {
+	{
+		.compatible = "mediatek,mt8167-smi-larb",
+		.data = &mtk_smi_larb_mt8167
+	},
 	{
 		.compatible = "mediatek,mt8173-smi-larb",
 		.data = &mtk_smi_larb_mt8173
@@ -418,6 +437,10 @@ static const struct of_device_id mtk_smi_common_of_ids[] = {
 		.compatible = "mediatek,mt8173-smi-common",
 		.data = &mtk_smi_common_gen2,
 	},
+	{
+		.compatible = "mediatek,mt8167-smi-common",
+		.data = &mtk_smi_common_gen2,
+	},
 	{
 		.compatible = "mediatek,mt2701-smi-common",
 		.data = &mtk_smi_common_gen1,

drivers/memory/renesas-rpc-if.c

@@ -199,10 +199,8 @@ int rpcif_sw_init(struct rpcif *rpc, struct device *dev)
 		rpc->dirmap = NULL;
 
 	rpc->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
-	if (IS_ERR(rpc->rstc))
-		return PTR_ERR(rpc->rstc);
 
-	return 0;
+	return PTR_ERR_OR_ZERO(rpc->rstc);
 }
 EXPORT_SYMBOL(rpcif_sw_init);
 

drivers/memory/tegra/tegra124-emc.c

@@ -1060,19 +1060,7 @@ static int tegra_emc_debug_available_rates_show(struct seq_file *s,
 	return 0;
 }
 
-static int tegra_emc_debug_available_rates_open(struct inode *inode,
-						struct file *file)
-{
-	return single_open(file, tegra_emc_debug_available_rates_show,
-			   inode->i_private);
-}
-
-static const struct file_operations tegra_emc_debug_available_rates_fops = {
-	.open = tegra_emc_debug_available_rates_open,
-	.read = seq_read,
-	.llseek = seq_lseek,
-	.release = single_release,
-};
+DEFINE_SHOW_ATTRIBUTE(tegra_emc_debug_available_rates);
 
 static int tegra_emc_debug_min_rate_get(void *data, u64 *rate)
 {

drivers/memory/tegra/tegra124.c

@@ -957,7 +957,6 @@ static const struct tegra_smmu_swgroup tegra124_swgroups[] = {
 static const unsigned int tegra124_group_drm[] = {
 	TEGRA_SWGROUP_DC,
 	TEGRA_SWGROUP_DCB,
-	TEGRA_SWGROUP_GPU,
 	TEGRA_SWGROUP_VIC,
 };
 

drivers/memory/tegra/tegra186-emc.c

@@ -172,14 +172,8 @@ static int tegra186_emc_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	emc->bpmp = tegra_bpmp_get(&pdev->dev);
-	if (IS_ERR(emc->bpmp)) {
-		err = PTR_ERR(emc->bpmp);
-
-		if (err != -EPROBE_DEFER)
-			dev_err(&pdev->dev, "failed to get BPMP: %d\n", err);
-
-		return err;
-	}
+	if (IS_ERR(emc->bpmp))
+		return dev_err_probe(&pdev->dev, PTR_ERR(emc->bpmp), "failed to get BPMP\n");
 
 	emc->clk = devm_clk_get(&pdev->dev, "emc");
 	if (IS_ERR(emc->clk)) {

drivers/memory/tegra/tegra210-emc-cc-r21021.c

@@ -501,7 +501,6 @@ static u32 tegra210_emc_r21021_periodic_compensation(struct tegra210_emc *emc)
 		emc_cfg_o = emc_readl(emc, EMC_CFG);
 		emc_cfg = emc_cfg_o & ~(EMC_CFG_DYN_SELF_REF |
 					EMC_CFG_DRAM_ACPD |
-					EMC_CFG_DRAM_CLKSTOP_PD |
 					EMC_CFG_DRAM_CLKSTOP_PD);
 
 

drivers/memory/tegra/tegra210.c

@@ -842,7 +842,7 @@ static const struct tegra_mc_client tegra210_mc_clients[] = {
 		},
 		.la = {
 			.reg = 0x3dc,
-			.shift = 0,
+			.shift = 16,
 			.mask = 0xff,
 			.def = 0x80,
 		},

drivers/reset/Kconfig

@@ -65,9 +65,10 @@ config RESET_HSDK
 	  This enables the reset controller driver for HSDK board.
 
 config RESET_IMX7
-	bool "i.MX7/8 Reset Driver" if COMPILE_TEST
+	tristate "i.MX7/8 Reset Driver"
 	depends on HAS_IOMEM
-	default SOC_IMX7D || (ARM64 && ARCH_MXC)
+	depends on SOC_IMX7D || (ARM64 && ARCH_MXC) || COMPILE_TEST
+	default y if SOC_IMX7D
 	select MFD_SYSCON
 	help
 	  This enables the reset controller driver for i.MX7 SoCs.

drivers/reset/core.c

@@ -32,7 +32,8 @@ static LIST_HEAD(reset_lookup_list);
  * @refcnt: Number of gets of this reset_control
  * @acquired: Only one reset_control may be acquired for a given rcdev and id.
  * @shared: Is this a shared (1), or an exclusive (0) reset_control?
- * @deassert_cnt: Number of times this reset line has been deasserted
+ * @array: Is this an array of reset controls (1)?
+ * @deassert_count: Number of times this reset line has been deasserted
  * @triggered_count: Number of times this reset line has been reset. Currently
  *                   only used for shared resets, which means that the value
  *                   will be either 0 or 1.

drivers/reset/reset-imx7.c

@@ -8,7 +8,7 @@
  */
 
 #include <linux/mfd/syscon.h>
-#include <linux/mod_devicetable.h>
+#include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/reset-controller.h>
@@ -178,6 +178,9 @@ static const struct imx7_src_signal imx8mq_src_signals[IMX8MQ_RESET_NUM] = {
 	[IMX8MQ_RESET_A53_SOC_DBG_RESET]	= { SRC_A53RCR0, BIT(20) },
 	[IMX8MQ_RESET_A53_L2RESET]		= { SRC_A53RCR0, BIT(21) },
 	[IMX8MQ_RESET_SW_NON_SCLR_M4C_RST]	= { SRC_M4RCR, BIT(0) },
+	[IMX8MQ_RESET_SW_M4C_RST]		= { SRC_M4RCR, BIT(1) },
+	[IMX8MQ_RESET_SW_M4P_RST]		= { SRC_M4RCR, BIT(2) },
+	[IMX8MQ_RESET_M4_ENABLE]		= { SRC_M4RCR, BIT(3) },
 	[IMX8MQ_RESET_OTG1_PHY_RESET]		= { SRC_USBOPHY1_RCR, BIT(0) },
 	[IMX8MQ_RESET_OTG2_PHY_RESET]		= { SRC_USBOPHY2_RCR, BIT(0) },
 	[IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N]	= { SRC_MIPIPHY_RCR, BIT(1) },
@@ -238,6 +241,7 @@ static int imx8mq_reset_set(struct reset_controller_dev *rcdev,
 	case IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N:
 	case IMX8MQ_RESET_MIPI_DSI_RESET_N:
 	case IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N:
+	case IMX8MQ_RESET_M4_ENABLE:
 		value = assert ? 0 : bit;
 		break;
 	}
@@ -386,6 +390,7 @@ static const struct of_device_id imx7_reset_dt_ids[] = {
 	{ .compatible = "fsl,imx8mp-src", .data = &variant_imx8mp },
 	{ /* sentinel */ },
 };
+MODULE_DEVICE_TABLE(of, imx7_reset_dt_ids);
 
 static struct platform_driver imx7_reset_driver = {
 	.probe	= imx7_reset_probe,
@@ -394,4 +399,8 @@ static struct platform_driver imx7_reset_driver = {
 		.of_match_table	= imx7_reset_dt_ids,
 	},
 };
-builtin_platform_driver(imx7_reset_driver);
+module_platform_driver(imx7_reset_driver);
+
+MODULE_AUTHOR("Andrey Smirnov <andrew.smirnov@gmail.com>");
+MODULE_DESCRIPTION("NXP i.MX7 reset driver");
+MODULE_LICENSE("GPL v2");

drivers/reset/reset-zynqmp.c

@@ -9,12 +9,20 @@
 #include <linux/platform_device.h>
 #include <linux/reset-controller.h>
 #include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/of_device.h>
 
 #define ZYNQMP_NR_RESETS (ZYNQMP_PM_RESET_END - ZYNQMP_PM_RESET_START)
 #define ZYNQMP_RESET_ID ZYNQMP_PM_RESET_START
+#define VERSAL_NR_RESETS	95
+
+struct zynqmp_reset_soc_data {
+	u32 reset_id;
+	u32 num_resets;
+};
 
 struct zynqmp_reset_data {
 	struct reset_controller_dev rcdev;
+	const struct zynqmp_reset_soc_data *data;
 };
 
 static inline struct zynqmp_reset_data *
@@ -26,23 +34,28 @@ to_zynqmp_reset_data(struct reset_controller_dev *rcdev)
 static int zynqmp_reset_assert(struct reset_controller_dev *rcdev,
 			       unsigned long id)
 {
-	return zynqmp_pm_reset_assert(ZYNQMP_RESET_ID + id,
+	struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+
+	return zynqmp_pm_reset_assert(priv->data->reset_id + id,
 				      PM_RESET_ACTION_ASSERT);
 }
 
 static int zynqmp_reset_deassert(struct reset_controller_dev *rcdev,
 				 unsigned long id)
 {
-	return zynqmp_pm_reset_assert(ZYNQMP_RESET_ID + id,
+	struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+
+	return zynqmp_pm_reset_assert(priv->data->reset_id + id,
 				      PM_RESET_ACTION_RELEASE);
 }
 
 static int zynqmp_reset_status(struct reset_controller_dev *rcdev,
 			       unsigned long id)
 {
+	struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
 	int val, err;
 
-	err = zynqmp_pm_reset_get_status(ZYNQMP_RESET_ID + id, &val);
+	err = zynqmp_pm_reset_get_status(priv->data->reset_id + id, &val);
 	if (err)
 		return err;
 
@@ -52,10 +65,28 @@ static int zynqmp_reset_status(struct reset_controller_dev *rcdev,
 static int zynqmp_reset_reset(struct reset_controller_dev *rcdev,
 			      unsigned long id)
 {
-	return zynqmp_pm_reset_assert(ZYNQMP_RESET_ID + id,
+	struct zynqmp_reset_data *priv = to_zynqmp_reset_data(rcdev);
+
+	return zynqmp_pm_reset_assert(priv->data->reset_id + id,
 				      PM_RESET_ACTION_PULSE);
 }
 
+static int zynqmp_reset_of_xlate(struct reset_controller_dev *rcdev,
+				 const struct of_phandle_args *reset_spec)
+{
+	return reset_spec->args[0];
+}
+
+static const struct zynqmp_reset_soc_data zynqmp_reset_data = {
+	.reset_id = ZYNQMP_RESET_ID,
+	.num_resets = ZYNQMP_NR_RESETS,
+};
+
+static const struct zynqmp_reset_soc_data versal_reset_data = {
+        .reset_id = 0,
+        .num_resets = VERSAL_NR_RESETS,
+};
+
 static const struct reset_control_ops zynqmp_reset_ops = {
 	.reset = zynqmp_reset_reset,
 	.assert = zynqmp_reset_assert,
@@ -71,18 +102,25 @@ static int zynqmp_reset_probe(struct platform_device *pdev)
 	if (!priv)
 		return -ENOMEM;
 
+	priv->data = of_device_get_match_data(&pdev->dev);
+	if (!priv->data)
+		return -EINVAL;
+
 	platform_set_drvdata(pdev, priv);
 
 	priv->rcdev.ops = &zynqmp_reset_ops;
 	priv->rcdev.owner = THIS_MODULE;
 	priv->rcdev.of_node = pdev->dev.of_node;
-	priv->rcdev.nr_resets = ZYNQMP_NR_RESETS;
+	priv->rcdev.nr_resets = priv->data->num_resets;
+	priv->rcdev.of_reset_n_cells = 1;
+	priv->rcdev.of_xlate = zynqmp_reset_of_xlate;
 
 	return devm_reset_controller_register(&pdev->dev, &priv->rcdev);
 }
 
 static const struct of_device_id zynqmp_reset_dt_ids[] = {
-	{ .compatible = "xlnx,zynqmp-reset", },
+	{ .compatible = "xlnx,zynqmp-reset", .data = &zynqmp_reset_data, },
+	{ .compatible = "xlnx,versal-reset", .data = &versal_reset_data, },
 	{ /* sentinel */ },
 };
 

drivers/reset/sti/reset-syscfg.c

@@ -17,7 +17,7 @@
 #include "reset-syscfg.h"
 
 /**
- * Reset channel regmap configuration
+ * struct syscfg_reset_channel - Reset channel regmap configuration
  *
  * @reset: regmap field for the channel's reset bit.
  * @ack: regmap field for the channel's ack bit (optional).
@@ -28,8 +28,9 @@ struct syscfg_reset_channel {
 };
 
 /**
- * A reset controller which groups together a set of related reset bits, which
- * may be located in different system configuration registers.
+ * struct syscfg_reset_controller - A reset controller which groups together
+ * a set of related reset bits, which may be located in different system
+ * configuration registers.
  *
  * @rst: base reset controller structure.
  * @active_low: are the resets in this controller active low, i.e. clearing

drivers/soc/amlogic/meson-ee-pwrc.c

@@ -15,6 +15,7 @@
 #include <linux/reset.h>
 #include <linux/clk.h>
 #include <dt-bindings/power/meson8-power.h>
+#include <dt-bindings/power/meson-axg-power.h>
 #include <dt-bindings/power/meson-g12a-power.h>
 #include <dt-bindings/power/meson-gxbb-power.h>
 #include <dt-bindings/power/meson-sm1-power.h>
@@ -134,6 +135,11 @@ static struct meson_ee_pwrc_top_domain sm1_pwrc_ge2d = SM1_EE_PD(19);
 	{ __reg, BIT(14) },					\
 	{ __reg, BIT(15) }
 
+static struct meson_ee_pwrc_mem_domain axg_pwrc_mem_vpu[] = {
+	VPU_MEMPD(HHI_VPU_MEM_PD_REG0),
+	VPU_HHI_MEMPD(HHI_MEM_PD_REG0),
+};
+
 static struct meson_ee_pwrc_mem_domain g12a_pwrc_mem_vpu[] = {
 	VPU_MEMPD(HHI_VPU_MEM_PD_REG0),
 	VPU_MEMPD(HHI_VPU_MEM_PD_REG1),
@@ -190,6 +196,10 @@ static struct meson_ee_pwrc_mem_domain sm1_pwrc_mem_ge2d[] = {
 	{ HHI_MEM_PD_REG0, GENMASK(25, 18) },
 };
 
+static struct meson_ee_pwrc_mem_domain axg_pwrc_mem_audio[] = {
+	{ HHI_MEM_PD_REG0, GENMASK(5, 4) },
+};
+
 static struct meson_ee_pwrc_mem_domain sm1_pwrc_mem_audio[] = {
 	{ HHI_MEM_PD_REG0, GENMASK(5, 4) },
 	{ HHI_AUDIO_MEM_PD_REG0, GENMASK(1, 0) },
@@ -231,6 +241,13 @@ static struct meson_ee_pwrc_mem_domain sm1_pwrc_mem_audio[] = {
 
 static bool pwrc_ee_get_power(struct meson_ee_pwrc_domain *pwrc_domain);
 
+static struct meson_ee_pwrc_domain_desc axg_pwrc_domains[] = {
+	[PWRC_AXG_VPU_ID]  = VPU_PD("VPU", &gx_pwrc_vpu, axg_pwrc_mem_vpu,
+				     pwrc_ee_get_power, 5, 2),
+	[PWRC_AXG_ETHERNET_MEM_ID] = MEM_PD("ETH", meson_pwrc_mem_eth),
+	[PWRC_AXG_AUDIO_ID] = MEM_PD("AUDIO", axg_pwrc_mem_audio),
+};
+
 static struct meson_ee_pwrc_domain_desc g12a_pwrc_domains[] = {
 	[PWRC_G12A_VPU_ID]  = VPU_PD("VPU", &gx_pwrc_vpu, g12a_pwrc_mem_vpu,
 				     pwrc_ee_get_power, 11, 2),
@@ -433,8 +450,8 @@ static int meson_ee_pwrc_init_domain(struct platform_device *pdev,
 		if (ret)
 			return ret;
 
-		ret = pm_genpd_init(&dom->base, &pm_domain_always_on_gov,
-				    false);
+		dom->base.flags = GENPD_FLAG_ALWAYS_ON;
+		ret = pm_genpd_init(&dom->base, NULL, false);
 		if (ret)
 			return ret;
 	} else {
@@ -529,6 +546,11 @@ static struct meson_ee_pwrc_domain_data meson_ee_g12a_pwrc_data = {
 	.domains = g12a_pwrc_domains,
 };
 
+static struct meson_ee_pwrc_domain_data meson_ee_axg_pwrc_data = {
+	.count = ARRAY_SIZE(axg_pwrc_domains),
+	.domains = axg_pwrc_domains,
+};
+
 static struct meson_ee_pwrc_domain_data meson_ee_gxbb_pwrc_data = {
 	.count = ARRAY_SIZE(gxbb_pwrc_domains),
 	.domains = gxbb_pwrc_domains,
@@ -562,6 +584,10 @@ static const struct of_device_id meson_ee_pwrc_match_table[] = {
 		.compatible = "amlogic,meson8m2-pwrc",
 		.data = &meson_ee_m8b_pwrc_data,
 	},
+	{
+		.compatible = "amlogic,meson-axg-pwrc",
+		.data = &meson_ee_axg_pwrc_data,
+	},
 	{
 		.compatible = "amlogic,meson-gxbb-pwrc",
 		.data = &meson_ee_gxbb_pwrc_data,

drivers/soc/amlogic/meson-gx-pwrc-vpu.c

@@ -339,8 +339,8 @@ static int meson_gx_pwrc_vpu_probe(struct platform_device *pdev)
 			return ret;
 	}
 
-	pm_genpd_init(&vpu_pd->genpd, &pm_domain_always_on_gov,
-		      powered_off);
+	vpu_pd->genpd.flags = GENPD_FLAG_ALWAYS_ON;
+	pm_genpd_init(&vpu_pd->genpd, NULL, powered_off);
 
 	return of_genpd_add_provider_simple(pdev->dev.of_node,
 					    &vpu_pd->genpd);

drivers/soc/bcm/Kconfig

@@ -22,6 +22,15 @@ config RASPBERRYPI_POWER
 	  This enables support for the RPi power domains which can be enabled
 	  or disabled via the RPi firmware.
 
+config SOC_BCM63XX
+	bool "Broadcom 63xx SoC drivers"
+	depends on BMIPS_GENERIC || COMPILE_TEST
+	help
+	  Enables drivers for the Broadcom 63xx series of chips.
+	  Drivers can be enabled individually within this menu.
+
+	  If unsure, say N.
+
 config SOC_BRCMSTB
 	bool "Broadcom STB SoC drivers"
 	depends on ARM || ARM64 || BMIPS_GENERIC || COMPILE_TEST
@@ -33,6 +42,7 @@ config SOC_BRCMSTB
 
 	  If unsure, say N.
 
+source "drivers/soc/bcm/bcm63xx/Kconfig"
 source "drivers/soc/bcm/brcmstb/Kconfig"
 
 endmenu

drivers/soc/bcm/Makefile

 # SPDX-License-Identifier: GPL-2.0-only
 obj-$(CONFIG_BCM2835_POWER)	+= bcm2835-power.o
 obj-$(CONFIG_RASPBERRYPI_POWER)	+= raspberrypi-power.o
+obj-$(CONFIG_SOC_BCM63XX)	+= bcm63xx/
 obj-$(CONFIG_SOC_BRCMSTB)	+= brcmstb/

drivers/soc/bcm/bcm63xx/Kconfig

+# SPDX-License-Identifier: GPL-2.0-only
+if SOC_BCM63XX
+
+config BCM63XX_POWER
+	bool "BCM63xx power domain driver"
+	depends on BMIPS_GENERIC || (COMPILE_TEST && OF)
+	select PM_GENERIC_DOMAINS if PM
+	help
+	  This enables support for the BCM63xx power domains controller on
+	  BCM6318, BCM6328, BCM6362 and BCM63268 SoCs.
+
+endif # SOC_BCM63XX

drivers/soc/bcm/bcm63xx/Makefile

+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_BCM63XX_POWER) += bcm63xx-power.o

drivers/soc/bcm/bcm63xx/bcm63xx-power.c

+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * BCM63xx Power Domain Controller Driver
+ *
+ * Copyright (C) 2020 Álvaro Fernández Rojas <noltari@gmail.com>
+ */
+
+#include <dt-bindings/soc/bcm6318-pm.h>
+#include <dt-bindings/soc/bcm6328-pm.h>
+#include <dt-bindings/soc/bcm6362-pm.h>
+#include <dt-bindings/soc/bcm63268-pm.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pm_domain.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+
+struct bcm63xx_power_dev {
+	struct generic_pm_domain genpd;
+	struct bcm63xx_power *power;
+	uint32_t mask;
+};
+
+struct bcm63xx_power {
+	void __iomem *base;
+	spinlock_t lock;
+	struct bcm63xx_power_dev *dev;
+	struct genpd_onecell_data genpd_data;
+	struct generic_pm_domain **genpd;
+};
+
+struct bcm63xx_power_data {
+	const char * const name;
+	uint8_t bit;
+	unsigned int flags;
+};
+
+static int bcm63xx_power_get_state(struct bcm63xx_power_dev *pmd, bool *is_on)
+{
+	struct bcm63xx_power *power = pmd->power;
+
+	if (!pmd->mask) {
+		*is_on = false;
+		return -EINVAL;
+	}
+
+	*is_on = !(__raw_readl(power->base) & pmd->mask);
+
+	return 0;
+}
+
+static int bcm63xx_power_set_state(struct bcm63xx_power_dev *pmd, bool on)
+{
+	struct bcm63xx_power *power = pmd->power;
+	unsigned long flags;
+	uint32_t val;
+
+	if (!pmd->mask)
+		return -EINVAL;
+
+	spin_lock_irqsave(&power->lock, flags);
+	val = __raw_readl(power->base);
+	if (on)
+		val &= ~pmd->mask;
+	else
+		val |= pmd->mask;
+	__raw_writel(val, power->base);
+	spin_unlock_irqrestore(&power->lock, flags);
+
+	return 0;
+}
+
+static int bcm63xx_power_on(struct generic_pm_domain *genpd)
+{
+	struct bcm63xx_power_dev *pmd = container_of(genpd,
+		struct bcm63xx_power_dev, genpd);
+
+	return bcm63xx_power_set_state(pmd, true);
+}
+
+static int bcm63xx_power_off(struct generic_pm_domain *genpd)
+{
+	struct bcm63xx_power_dev *pmd = container_of(genpd,
+		struct bcm63xx_power_dev, genpd);
+
+	return bcm63xx_power_set_state(pmd, false);
+}
+
+static int bcm63xx_power_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct resource *res;
+	const struct bcm63xx_power_data *entry, *table;
+	struct bcm63xx_power *power;
+	unsigned int ndom;
+	uint8_t max_bit = 0;
+	int ret;
+
+	power = devm_kzalloc(dev, sizeof(*power), GFP_KERNEL);
+	if (!power)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	power->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(power->base))
+		return PTR_ERR(power->base);
+
+	table = of_device_get_match_data(dev);
+	if (!table)
+		return -EINVAL;
+
+	power->genpd_data.num_domains = 0;
+	ndom = 0;
+	for (entry = table; entry->name; entry++) {
+		max_bit = max(max_bit, entry->bit);
+		ndom++;
+	}
+
+	if (!ndom)
+		return -ENODEV;
+
+	power->genpd_data.num_domains = max_bit + 1;
+
+	power->dev = devm_kcalloc(dev, power->genpd_data.num_domains,
+				  sizeof(struct bcm63xx_power_dev),
+				  GFP_KERNEL);
+	if (!power->dev)
+		return -ENOMEM;
+
+	power->genpd = devm_kcalloc(dev, power->genpd_data.num_domains,
+				    sizeof(struct generic_pm_domain *),
+				    GFP_KERNEL);
+	if (!power->genpd)
+		return -ENOMEM;
+
+	power->genpd_data.domains = power->genpd;
+
+	ndom = 0;
+	for (entry = table; entry->name; entry++) {
+		struct bcm63xx_power_dev *pmd = &power->dev[ndom];
+		bool is_on;
+
+		pmd->power = power;
+		pmd->mask = BIT(entry->bit);
+		pmd->genpd.name = entry->name;
+		pmd->genpd.flags = entry->flags;
+
+		ret = bcm63xx_power_get_state(pmd, &is_on);
+		if (ret)
+			dev_warn(dev, "unable to get current state for %s\n",
+				 pmd->genpd.name);
+
+		pmd->genpd.power_on = bcm63xx_power_on;
+		pmd->genpd.power_off = bcm63xx_power_off;
+
+		pm_genpd_init(&pmd->genpd, NULL, !is_on);
+		power->genpd[entry->bit] = &pmd->genpd;
+
+		ndom++;
+	}
+
+	spin_lock_init(&power->lock);
+
+	ret = of_genpd_add_provider_onecell(np, &power->genpd_data);
+	if (ret) {
+		dev_err(dev, "failed to register genpd driver: %d\n", ret);
+		return ret;
+	}
+
+	dev_info(dev, "registered %u power domains\n", ndom);
+
+	return 0;
+}
+
+static const struct bcm63xx_power_data bcm6318_power_domains[] = {
+	{
+		.name = "pcie",
+		.bit = BCM6318_POWER_DOMAIN_PCIE,
+	}, {
+		.name = "usb",
+		.bit = BCM6318_POWER_DOMAIN_USB,
+	}, {
+		.name = "ephy0",
+		.bit = BCM6318_POWER_DOMAIN_EPHY0,
+	}, {
+		.name = "ephy1",
+		.bit = BCM6318_POWER_DOMAIN_EPHY1,
+	}, {
+		.name = "ephy2",
+		.bit = BCM6318_POWER_DOMAIN_EPHY2,
+	}, {
+		.name = "ephy3",
+		.bit = BCM6318_POWER_DOMAIN_EPHY3,
+	}, {
+		.name = "ldo2p5",
+		.bit = BCM6318_POWER_DOMAIN_LDO2P5,
+		.flags = GENPD_FLAG_ALWAYS_ON,
+	}, {
+		.name = "ldo2p9",
+		.bit = BCM6318_POWER_DOMAIN_LDO2P9,
+		.flags = GENPD_FLAG_ALWAYS_ON,
+	}, {
+		.name = "sw1p0",
+		.bit = BCM6318_POWER_DOMAIN_SW1P0,
+		.flags = GENPD_FLAG_ALWAYS_ON,
+	}, {
+		.name = "pad",
+		.bit = BCM6318_POWER_DOMAIN_PAD,
+		.flags = GENPD_FLAG_ALWAYS_ON,
+	}, {
+		/* sentinel */
+	},
+};
+
+static const struct bcm63xx_power_data bcm6328_power_domains[] = {
+	{
+		.name = "adsl2-mips",
+		.bit = BCM6328_POWER_DOMAIN_ADSL2_MIPS,
+	}, {
+		.name = "adsl2-phy",
+		.bit = BCM6328_POWER_DOMAIN_ADSL2_PHY,
+	}, {
+		.name = "adsl2-afe",
+		.bit = BCM6328_POWER_DOMAIN_ADSL2_AFE,
+	}, {
+		.name = "sar",
+		.bit = BCM6328_POWER_DOMAIN_SAR,
+	}, {
+		.name = "pcm",
+		.bit = BCM6328_POWER_DOMAIN_PCM,
+	}, {
+		.name = "usbd",
+		.bit = BCM6328_POWER_DOMAIN_USBD,
+	}, {
+		.name = "usbh",
+		.bit = BCM6328_POWER_DOMAIN_USBH,
+	}, {
+		.name = "pcie",
+		.bit = BCM6328_POWER_DOMAIN_PCIE,
+	}, {
+		.name = "robosw",
+		.bit = BCM6328_POWER_DOMAIN_ROBOSW,
+	}, {
+		.name = "ephy",
+		.bit = BCM6328_POWER_DOMAIN_EPHY,
+	}, {
+		/* sentinel */
+	},
+};
+
+static const struct bcm63xx_power_data bcm6362_power_domains[] = {
+	{
+		.name = "sar",
+		.bit = BCM6362_POWER_DOMAIN_SAR,
+	}, {
+		.name = "ipsec",
+		.bit = BCM6362_POWER_DOMAIN_IPSEC,
+	}, {
+		.name = "mips",
+		.bit = BCM6362_POWER_DOMAIN_MIPS,
+		.flags = GENPD_FLAG_ALWAYS_ON,
+	}, {
+		.name = "dect",
+		.bit = BCM6362_POWER_DOMAIN_DECT,
+	}, {
+		.name = "usbh",
+		.bit = BCM6362_POWER_DOMAIN_USBH,
+	}, {
+		.name = "usbd",
+		.bit = BCM6362_POWER_DOMAIN_USBD,
+	}, {
+		.name = "robosw",
+		.bit = BCM6362_POWER_DOMAIN_ROBOSW,
+	}, {
+		.name = "pcm",
+		.bit = BCM6362_POWER_DOMAIN_PCM,
+	}, {
+		.name = "periph",
+		.bit = BCM6362_POWER_DOMAIN_PERIPH,
+		.flags = GENPD_FLAG_ALWAYS_ON,
+	}, {
+		.name = "adsl-phy",
+		.bit = BCM6362_POWER_DOMAIN_ADSL_PHY,
+	}, {
+		.name = "gmii-pads",
+		.bit = BCM6362_POWER_DOMAIN_GMII_PADS,
+	}, {
+		.name = "fap",
+		.bit = BCM6362_POWER_DOMAIN_FAP,
+	}, {
+		.name = "pcie",
+		.bit = BCM6362_POWER_DOMAIN_PCIE,
+	}, {
+		.name = "wlan-pads",
+		.bit = BCM6362_POWER_DOMAIN_WLAN_PADS,
+	}, {
+		/* sentinel */
+	},
+};
+
+static const struct bcm63xx_power_data bcm63268_power_domains[] = {
+	{
+		.name = "sar",
+		.bit = BCM63268_POWER_DOMAIN_SAR,
+	}, {
+		.name = "ipsec",
+		.bit = BCM63268_POWER_DOMAIN_IPSEC,
+	}, {
+		.name = "mips",
+		.bit = BCM63268_POWER_DOMAIN_MIPS,
+		.flags = GENPD_FLAG_ALWAYS_ON,
+	}, {
+		.name = "dect",
+		.bit = BCM63268_POWER_DOMAIN_DECT,
+	}, {
+		.name = "usbh",
+		.bit = BCM63268_POWER_DOMAIN_USBH,
+	}, {
+		.name = "usbd",
+		.bit = BCM63268_POWER_DOMAIN_USBD,
+	}, {
+		.name = "robosw",
+		.bit = BCM63268_POWER_DOMAIN_ROBOSW,
+	}, {
+		.name = "pcm",
+		.bit = BCM63268_POWER_DOMAIN_PCM,
+	}, {
+		.name = "periph",
+		.bit = BCM63268_POWER_DOMAIN_PERIPH,
+		.flags = GENPD_FLAG_ALWAYS_ON,
+	}, {
+		.name = "vdsl-phy",
+		.bit = BCM63268_POWER_DOMAIN_VDSL_PHY,
+	}, {
+		.name = "vdsl-mips",
+		.bit = BCM63268_POWER_DOMAIN_VDSL_MIPS,
+	}, {
+		.name = "fap",
+		.bit = BCM63268_POWER_DOMAIN_FAP,
+	}, {
+		.name = "pcie",
+		.bit = BCM63268_POWER_DOMAIN_PCIE,
+	}, {
+		.name = "wlan-pads",
+		.bit = BCM63268_POWER_DOMAIN_WLAN_PADS,
+	}, {
+		/* sentinel */
+	},
+};
+
+static const struct of_device_id bcm63xx_power_of_match[] = {
+	{
+		.compatible = "brcm,bcm6318-power-controller",
+		.data = &bcm6318_power_domains,
+	}, {
+		.compatible = "brcm,bcm6328-power-controller",
+		.data = &bcm6328_power_domains,
+	}, {
+		.compatible = "brcm,bcm6362-power-controller",
+		.data = &bcm6362_power_domains,
+	}, {
+		.compatible = "brcm,bcm63268-power-controller",
+		.data = &bcm63268_power_domains,
+	}, {
+		/* sentinel */
+	}
+};
+
+static struct platform_driver bcm63xx_power_driver = {
+	.driver = {
+		.name = "bcm63xx-power-controller",
+		.of_match_table = bcm63xx_power_of_match,
+	},
+	.probe  = bcm63xx_power_probe,
+};
+builtin_platform_driver(bcm63xx_power_driver);

drivers/soc/bcm/brcmstb/biuctrl.c

@@ -13,6 +13,22 @@
 #include <linux/syscore_ops.h>
 #include <linux/soc/brcmstb/brcmstb.h>
 
+#define RACENPREF_MASK			0x3
+#define RACPREFINST_SHIFT		0
+#define RACENINST_SHIFT			2
+#define RACPREFDATA_SHIFT		4
+#define RACENDATA_SHIFT			6
+#define RAC_CPU_SHIFT			8
+#define RACCFG_MASK			0xff
+#define DPREF_LINE_2_SHIFT		24
+#define DPREF_LINE_2_MASK		0xff
+
+/* Bitmask to enable instruction and data prefetching with a 256-bytes stride */
+#define RAC_DATA_INST_EN_MASK		(1 << RACPREFINST_SHIFT | \
+					 RACENPREF_MASK << RACENINST_SHIFT | \
+					 1 << RACPREFDATA_SHIFT | \
+					 RACENPREF_MASK << RACENDATA_SHIFT)
+
 #define  CPU_CREDIT_REG_MCPx_WR_PAIRING_EN_MASK	0x70000000
 #define CPU_CREDIT_REG_MCPx_READ_CRED_MASK	0xf
 #define CPU_CREDIT_REG_MCPx_WRITE_CRED_MASK	0xf
@@ -31,11 +47,21 @@ static void __iomem *cpubiuctrl_base;
 static bool mcp_wr_pairing_en;
 static const int *cpubiuctrl_regs;
 
+enum cpubiuctrl_regs {
+	CPU_CREDIT_REG = 0,
+	CPU_MCP_FLOW_REG,
+	CPU_WRITEBACK_CTRL_REG,
+	RAC_CONFIG0_REG,
+	RAC_CONFIG1_REG,
+	NUM_CPU_BIUCTRL_REGS,
+};
+
 static inline u32 cbc_readl(int reg)
 {
 	int offset = cpubiuctrl_regs[reg];
 
-	if (offset == -1)
+	if (offset == -1 ||
+	    (IS_ENABLED(CONFIG_CACHE_B15_RAC) && reg >= RAC_CONFIG0_REG))
 		return (u32)-1;
 
 	return readl_relaxed(cpubiuctrl_base + offset);
@@ -45,22 +71,19 @@ static inline void cbc_writel(u32 val, int reg)
 {
 	int offset = cpubiuctrl_regs[reg];
 
-	if (offset == -1)
+	if (offset == -1 ||
+	    (IS_ENABLED(CONFIG_CACHE_B15_RAC) && reg >= RAC_CONFIG0_REG))
 		return;
 
 	writel(val, cpubiuctrl_base + offset);
 }
 
-enum cpubiuctrl_regs {
-	CPU_CREDIT_REG = 0,
-	CPU_MCP_FLOW_REG,
-	CPU_WRITEBACK_CTRL_REG
-};
-
 static const int b15_cpubiuctrl_regs[] = {
 	[CPU_CREDIT_REG] = 0x184,
 	[CPU_MCP_FLOW_REG] = -1,
 	[CPU_WRITEBACK_CTRL_REG] = -1,
+	[RAC_CONFIG0_REG] = -1,
+	[RAC_CONFIG1_REG] = -1,
 };
 
 /* Odd cases, e.g: 7260A0 */
@@ -68,22 +91,26 @@ static const int b53_cpubiuctrl_no_wb_regs[] = {
 	[CPU_CREDIT_REG] = 0x0b0,
 	[CPU_MCP_FLOW_REG] = 0x0b4,
 	[CPU_WRITEBACK_CTRL_REG] = -1,
+	[RAC_CONFIG0_REG] = 0x78,
+	[RAC_CONFIG1_REG] = 0x7c,
 };
 
 static const int b53_cpubiuctrl_regs[] = {
 	[CPU_CREDIT_REG] = 0x0b0,
 	[CPU_MCP_FLOW_REG] = 0x0b4,
 	[CPU_WRITEBACK_CTRL_REG] = 0x22c,
+	[RAC_CONFIG0_REG] = 0x78,
+	[RAC_CONFIG1_REG] = 0x7c,
 };
 
 static const int a72_cpubiuctrl_regs[] = {
 	[CPU_CREDIT_REG] = 0x18,
 	[CPU_MCP_FLOW_REG] = 0x1c,
 	[CPU_WRITEBACK_CTRL_REG] = 0x20,
+	[RAC_CONFIG0_REG] = 0x08,
+	[RAC_CONFIG1_REG] = 0x0c,
 };
 
-#define NUM_CPU_BIUCTRL_REGS	3
-
 static int __init mcp_write_pairing_set(void)
 {
 	u32 creds = 0;
@@ -110,6 +137,8 @@ static int __init mcp_write_pairing_set(void)
 static const u32 a72_b53_mach_compat[] = {
 	0x7211,
 	0x7216,
+	0x72164,
+	0x72165,
 	0x7255,
 	0x7260,
 	0x7268,
@@ -117,6 +146,61 @@ static const u32 a72_b53_mach_compat[] = {
 	0x7278,
 };
 
+/* The read-ahead cache present in the Brahma-B53 CPU is a special piece of
+ * hardware after the integrated L2 cache of the B53 CPU complex whose purpose
+ * is to prefetch instruction and/or data with a line size of either 64 bytes
+ * or 256 bytes. The rationale is that the data-bus of the CPU interface is
+ * optimized for 256-byte transactions, and enabling the read-ahead cache
+ * provides a significant performance boost (typically twice the performance
+ * for a memcpy benchmark application).
+ *
+ * The read-ahead cache is transparent for Virtual Address cache maintenance
+ * operations: IC IVAU, DC IVAC, DC CVAC, DC CVAU and DC CIVAC.  So no special
+ * handling is needed for the DMA API above and beyond what is included in the
+ * arm64 implementation.
+ *
+ * In addition, since the Point of Unification is typically between L1 and L2
+ * for the Brahma-B53 processor no special read-ahead cache handling is needed
+ * for the IC IALLU and IC IALLUIS cache maintenance operations.
+ *
+ * However, it is not possible to specify the cache level (L3) for the cache
+ * maintenance instructions operating by set/way to operate on the read-ahead
+ * cache.  The read-ahead cache will maintain coherency when inner cache lines
+ * are cleaned by set/way, but if it is necessary to invalidate inner cache
+ * lines by set/way to maintain coherency with system masters operating on
+ * shared memory that does not have hardware support for coherency, then it
+ * will also be necessary to explicitly invalidate the read-ahead cache.
+ */
+static void __init a72_b53_rac_enable_all(struct device_node *np)
+{
+	unsigned int cpu;
+	u32 enable = 0, pref_dist, shift;
+
+	if (IS_ENABLED(CONFIG_CACHE_B15_RAC))
+		return;
+
+	if (WARN(num_possible_cpus() > 4, "RAC only supports 4 CPUs\n"))
+		return;
+
+	pref_dist = cbc_readl(RAC_CONFIG1_REG);
+	for_each_possible_cpu(cpu) {
+		shift = cpu * RAC_CPU_SHIFT + RACPREFDATA_SHIFT;
+		enable |= RAC_DATA_INST_EN_MASK << (cpu * RAC_CPU_SHIFT);
+		if (cpubiuctrl_regs == a72_cpubiuctrl_regs) {
+			enable &= ~(RACENPREF_MASK << shift);
+			enable |= 3 << shift;
+			pref_dist |= 1 << (cpu + DPREF_LINE_2_SHIFT);
+		}
+	}
+
+	cbc_writel(enable, RAC_CONFIG0_REG);
+	cbc_writel(pref_dist, RAC_CONFIG1_REG);
+
+	pr_info("%pOF: Broadcom %s read-ahead cache\n",
+		np, cpubiuctrl_regs == a72_cpubiuctrl_regs ?
+		"Cortex-A72" : "Brahma-B53");
+}
+
 static void __init mcp_a72_b53_set(void)
 {
 	unsigned int i;
@@ -262,6 +346,7 @@ static int __init brcmstb_biuctrl_init(void)
 		return ret;
 	}
 
+	a72_b53_rac_enable_all(np);
 	mcp_a72_b53_set();
 #ifdef CONFIG_PM_SLEEP
 	register_syscore_ops(&brcmstb_cpu_credit_syscore_ops);

drivers/soc/fsl/dpio/qbman-portal.c

@@ -647,7 +647,6 @@ int qbman_swp_enqueue_multiple_direct(struct qbman_swp *s,
 	const uint32_t *cl = (uint32_t *)d;
 	uint32_t eqcr_ci, eqcr_pi, half_mask, full_mask;
 	int i, num_enqueued = 0;
-	uint64_t addr_cena;
 
 	spin_lock(&s->access_spinlock);
 	half_mask = (s->eqcr.pi_ci_mask>>1);
@@ -701,7 +700,6 @@ int qbman_swp_enqueue_multiple_direct(struct qbman_swp *s,
 
 	/* Flush all the cacheline without load/store in between */
 	eqcr_pi = s->eqcr.pi;
-	addr_cena = (size_t)s->addr_cena;
 	for (i = 0; i < num_enqueued; i++)
 		eqcr_pi++;
 	s->eqcr.pi = eqcr_pi & full_mask;

drivers/soc/fsl/qbman/bman.c

@@ -660,7 +660,7 @@ int bm_shutdown_pool(u32 bpid)
 	}
 done:
 	put_affine_portal();
-	return 0;
+	return err;
 }
 
 struct gen_pool *bm_bpalloc;

drivers/soc/fsl/qbman/qman_test_api.c

@@ -86,7 +86,7 @@ static void fd_inc(struct qm_fd *fd)
 	len--;
 	qm_fd_set_param(fd, fmt, off, len);
 
-	fd->cmd = cpu_to_be32(be32_to_cpu(fd->cmd) + 1);
+	be32_add_cpu(&fd->cmd, 1);
 }
 
 /* The only part of the 'fd' we can't memcmp() is the ppid */

drivers/soc/fsl/qe/ucc.c

@@ -523,7 +523,7 @@ int ucc_set_tdm_rxtx_clk(u32 tdm_num, enum qe_clock clock,
 
 	qe_mux_reg = &qe_immr->qmx;
 
-	if (tdm_num > 7 || tdm_num < 0)
+	if (tdm_num > 7)
 		return -EINVAL;
 
 	/* The communications direction must be RX or TX */

drivers/soc/imx/gpcv2.c

@@ -487,22 +487,17 @@ static int imx_pgc_domain_probe(struct platform_device *pdev)
 
 	domain->regulator = devm_regulator_get_optional(domain->dev, "power");
 	if (IS_ERR(domain->regulator)) {
-		if (PTR_ERR(domain->regulator) != -ENODEV) {
-			if (PTR_ERR(domain->regulator) != -EPROBE_DEFER)
-				dev_err(domain->dev, "Failed to get domain's regulator\n");
-			return PTR_ERR(domain->regulator);
-		}
+		if (PTR_ERR(domain->regulator) != -ENODEV)
+			return dev_err_probe(domain->dev, PTR_ERR(domain->regulator),
+					     "Failed to get domain's regulator\n");
 	} else if (domain->voltage) {
 		regulator_set_voltage(domain->regulator,
 				      domain->voltage, domain->voltage);
 	}
 
 	ret = imx_pgc_get_clocks(domain);
-	if (ret) {
-		if (ret != -EPROBE_DEFER)
-			dev_err(domain->dev, "Failed to get domain's clocks\n");
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(domain->dev, ret, "Failed to get domain's clocks\n");
 
 	ret = pm_genpd_init(&domain->genpd, NULL, true);
 	if (ret) {

drivers/soc/mediatek/mtk-cmdq-helper.c

@@ -13,11 +13,16 @@
 #define CMDQ_POLL_ENABLE_MASK	BIT(0)
 #define CMDQ_EOC_IRQ_EN		BIT(0)
 #define CMDQ_REG_TYPE		1
+#define CMDQ_JUMP_RELATIVE	1
 
 struct cmdq_instruction {
 	union {
 		u32 value;
 		u32 mask;
+		struct {
+			u16 arg_c;
+			u16 src_reg;
+		};
 	};
 	union {
 		u16 offset;
@@ -223,15 +228,104 @@ int cmdq_pkt_write_mask(struct cmdq_pkt *pkt, u8 subsys,
 }
 EXPORT_SYMBOL(cmdq_pkt_write_mask);
 
-int cmdq_pkt_wfe(struct cmdq_pkt *pkt, u16 event)
+int cmdq_pkt_read_s(struct cmdq_pkt *pkt, u16 high_addr_reg_idx, u16 addr_low,
+		    u16 reg_idx)
+{
+	struct cmdq_instruction inst = {};
+
+	inst.op = CMDQ_CODE_READ_S;
+	inst.dst_t = CMDQ_REG_TYPE;
+	inst.sop = high_addr_reg_idx;
+	inst.reg_dst = reg_idx;
+	inst.src_reg = addr_low;
+
+	return cmdq_pkt_append_command(pkt, inst);
+}
+EXPORT_SYMBOL(cmdq_pkt_read_s);
+
+int cmdq_pkt_write_s(struct cmdq_pkt *pkt, u16 high_addr_reg_idx,
+		     u16 addr_low, u16 src_reg_idx)
+{
+	struct cmdq_instruction inst = {};
+
+	inst.op = CMDQ_CODE_WRITE_S;
+	inst.src_t = CMDQ_REG_TYPE;
+	inst.sop = high_addr_reg_idx;
+	inst.offset = addr_low;
+	inst.src_reg = src_reg_idx;
+
+	return cmdq_pkt_append_command(pkt, inst);
+}
+EXPORT_SYMBOL(cmdq_pkt_write_s);
+
+int cmdq_pkt_write_s_mask(struct cmdq_pkt *pkt, u16 high_addr_reg_idx,
+			  u16 addr_low, u16 src_reg_idx, u32 mask)
+{
+	struct cmdq_instruction inst = {};
+	int err;
+
+	inst.op = CMDQ_CODE_MASK;
+	inst.mask = ~mask;
+	err = cmdq_pkt_append_command(pkt, inst);
+	if (err < 0)
+		return err;
+
+	inst.mask = 0;
+	inst.op = CMDQ_CODE_WRITE_S_MASK;
+	inst.src_t = CMDQ_REG_TYPE;
+	inst.sop = high_addr_reg_idx;
+	inst.offset = addr_low;
+	inst.src_reg = src_reg_idx;
+
+	return cmdq_pkt_append_command(pkt, inst);
+}
+EXPORT_SYMBOL(cmdq_pkt_write_s_mask);
+
+int cmdq_pkt_write_s_value(struct cmdq_pkt *pkt, u8 high_addr_reg_idx,
+			   u16 addr_low, u32 value)
+{
+	struct cmdq_instruction inst = {};
+
+	inst.op = CMDQ_CODE_WRITE_S;
+	inst.sop = high_addr_reg_idx;
+	inst.offset = addr_low;
+	inst.value = value;
+
+	return cmdq_pkt_append_command(pkt, inst);
+}
+EXPORT_SYMBOL(cmdq_pkt_write_s_value);
+
+int cmdq_pkt_write_s_mask_value(struct cmdq_pkt *pkt, u8 high_addr_reg_idx,
+				u16 addr_low, u32 value, u32 mask)
+{
+	struct cmdq_instruction inst = {};
+	int err;
+
+	inst.op = CMDQ_CODE_MASK;
+	inst.mask = ~mask;
+	err = cmdq_pkt_append_command(pkt, inst);
+	if (err < 0)
+		return err;
+
+	inst.op = CMDQ_CODE_WRITE_S_MASK;
+	inst.sop = high_addr_reg_idx;
+	inst.offset = addr_low;
+	inst.value = value;
+
+	return cmdq_pkt_append_command(pkt, inst);
+}
+EXPORT_SYMBOL(cmdq_pkt_write_s_mask_value);
+
+int cmdq_pkt_wfe(struct cmdq_pkt *pkt, u16 event, bool clear)
 {
 	struct cmdq_instruction inst = { {0} };
+	u32 clear_option = clear ? CMDQ_WFE_UPDATE : 0;
 
 	if (event >= CMDQ_MAX_EVENT)
 		return -EINVAL;
 
 	inst.op = CMDQ_CODE_WFE;
-	inst.value = CMDQ_WFE_OPTION;
+	inst.value = CMDQ_WFE_OPTION | clear_option;
 	inst.event = event;
 
 	return cmdq_pkt_append_command(pkt, inst);
@@ -315,6 +409,18 @@ int cmdq_pkt_assign(struct cmdq_pkt *pkt, u16 reg_idx, u32 value)
 }
 EXPORT_SYMBOL(cmdq_pkt_assign);
 
+int cmdq_pkt_jump(struct cmdq_pkt *pkt, dma_addr_t addr)
+{
+	struct cmdq_instruction inst = {};
+
+	inst.op = CMDQ_CODE_JUMP;
+	inst.offset = CMDQ_JUMP_RELATIVE;
+	inst.value = addr >>
+		cmdq_get_shift_pa(((struct cmdq_client *)pkt->cl)->chan);
+	return cmdq_pkt_append_command(pkt, inst);
+}
+EXPORT_SYMBOL(cmdq_pkt_jump);
+
 int cmdq_pkt_finalize(struct cmdq_pkt *pkt)
 {
 	struct cmdq_instruction inst = { {0} };
@@ -329,7 +435,8 @@ int cmdq_pkt_finalize(struct cmdq_pkt *pkt)
 
 	/* JUMP to end */
 	inst.op = CMDQ_CODE_JUMP;
-	inst.value = CMDQ_JUMP_PASS;
+	inst.value = CMDQ_JUMP_PASS >>
+		cmdq_get_shift_pa(((struct cmdq_client *)pkt->cl)->chan);
 	err = cmdq_pkt_append_command(pkt, inst);
 
 	return err;

drivers/soc/mediatek/mtk-infracfg.c

@@ -19,7 +19,7 @@
 
 /**
  * mtk_infracfg_set_bus_protection - enable bus protection
- * @regmap: The infracfg regmap
+ * @infracfg: The infracfg regmap
  * @mask: The mask containing the protection bits to be enabled.
  * @reg_update: The boolean flag determines to set the protection bits
  *              by regmap_update_bits with enable register(PROTECTEN) or
@@ -50,7 +50,7 @@ int mtk_infracfg_set_bus_protection(struct regmap *infracfg, u32 mask,
 
 /**
  * mtk_infracfg_clear_bus_protection - disable bus protection
- * @regmap: The infracfg regmap
+ * @infracfg: The infracfg regmap
  * @mask: The mask containing the protection bits to be disabled.
  * @reg_update: The boolean flag determines to clear the protection bits
  *              by regmap_update_bits with enable register(PROTECTEN) or

drivers/soc/qcom/apr.c

@@ -328,7 +328,7 @@ static int of_apr_add_pd_lookups(struct device *dev)
 
 		pds = pdr_add_lookup(apr->pdr, service_name, service_path);
 		if (IS_ERR(pds) && PTR_ERR(pds) != -EALREADY) {
-			dev_err(dev, "pdr add lookup failed: %d\n", ret);
+			dev_err(dev, "pdr add lookup failed: %ld\n", PTR_ERR(pds));
 			return PTR_ERR(pds);
 		}
 	}

drivers/soc/qcom/llcc-qcom.c

@@ -387,7 +387,6 @@ static int qcom_llcc_remove(struct platform_device *pdev)
 static struct regmap *qcom_llcc_init_mmio(struct platform_device *pdev,
 		const char *name)
 {
-	struct resource *res;
 	void __iomem *base;
 	struct regmap_config llcc_regmap_config = {
 		.reg_bits = 32,
@@ -396,11 +395,7 @@ static struct regmap *qcom_llcc_init_mmio(struct platform_device *pdev,
 		.fast_io = true,
 	};
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, name);
-	if (!res)
-		return ERR_PTR(-ENODEV);
-
-	base = devm_ioremap_resource(&pdev->dev, res);
+	base = devm_platform_ioremap_resource_byname(pdev, name);
 	if (IS_ERR(base))
 		return ERR_CAST(base);
 

drivers/soc/qcom/rpmh-internal.h

@@ -8,6 +8,7 @@
 #define __RPM_INTERNAL_H__
 
 #include <linux/bitmap.h>
+#include <linux/wait.h>
 #include <soc/qcom/tcs.h>
 
 #define TCS_TYPE_NR			4
@@ -106,6 +107,8 @@ struct rpmh_ctrlr {
  * @lock:               Synchronize state of the controller.  If RPMH's cache
  *                      lock will also be held, the order is: drv->lock then
  *                      cache_lock.
+ * @tcs_wait:           Wait queue used to wait for @tcs_in_use to free up a
+ *                      slot
  * @client:             Handle to the DRV's client.
  */
 struct rsc_drv {
@@ -118,6 +121,7 @@ struct rsc_drv {
 	struct tcs_group tcs[TCS_TYPE_NR];
 	DECLARE_BITMAP(tcs_in_use, MAX_TCS_NR);
 	spinlock_t lock;
+	wait_queue_head_t tcs_wait;
 	struct rpmh_ctrlr client;
 };
 

drivers/soc/qcom/rpmh-rsc.c

@@ -19,6 +19,7 @@
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
+#include <linux/wait.h>
 
 #include <soc/qcom/cmd-db.h>
 #include <soc/qcom/tcs.h>
@@ -453,6 +454,7 @@ static irqreturn_t tcs_tx_done(int irq, void *p)
 		if (!drv->tcs[ACTIVE_TCS].num_tcs)
 			enable_tcs_irq(drv, i, false);
 		spin_unlock(&drv->lock);
+		wake_up(&drv->tcs_wait);
 		if (req)
 			rpmh_tx_done(req, err);
 	}
@@ -571,73 +573,34 @@ static int find_free_tcs(struct tcs_group *tcs)
 }
 
 /**
- * tcs_write() - Store messages into a TCS right now, or return -EBUSY.
+ * claim_tcs_for_req() - Claim a tcs in the given tcs_group; only for active.
  * @drv: The controller.
+ * @tcs: The tcs_group used for ACTIVE_ONLY transfers.
  * @msg: The data to be sent.
  *
- * Grabs a TCS for ACTIVE_ONLY transfers and writes the messages to it.
+ * Claims a tcs in the given tcs_group while making sure that no existing cmd
+ * is in flight that would conflict with the one in @msg.
  *
- * If there are no free TCSes for ACTIVE_ONLY transfers or if a command for
- * the same address is already transferring returns -EBUSY which means the
- * client should retry shortly.
+ * Context: Must be called with the drv->lock held since that protects
+ * tcs_in_use.
  *
- * Return: 0 on success, -EBUSY if client should retry, or an error.
- *         Client should have interrupts enabled for a bit before retrying.
+ * Return: The id of the claimed tcs or -EBUSY if a matching msg is in flight
+ * or the tcs_group is full.
  */
-static int tcs_write(struct rsc_drv *drv, const struct tcs_request *msg)
+static int claim_tcs_for_req(struct rsc_drv *drv, struct tcs_group *tcs,
+			     const struct tcs_request *msg)
 {
-	struct tcs_group *tcs;
-	int tcs_id;
-	unsigned long flags;
 	int ret;
 
-	tcs = get_tcs_for_msg(drv, msg);
-	if (IS_ERR(tcs))
-		return PTR_ERR(tcs);
-
-	spin_lock_irqsave(&drv->lock, flags);
 	/*
 	 * The h/w does not like if we send a request to the same address,
 	 * when one is already in-flight or being processed.
 	 */
 	ret = check_for_req_inflight(drv, tcs, msg);
 	if (ret)
-		goto unlock;
-
-	ret = find_free_tcs(tcs);
-	if (ret < 0)
-		goto unlock;
-	tcs_id = ret;
-
-	tcs->req[tcs_id - tcs->offset] = msg;
-	set_bit(tcs_id, drv->tcs_in_use);
-	if (msg->state == RPMH_ACTIVE_ONLY_STATE && tcs->type != ACTIVE_TCS) {
-		/*
-		 * Clear previously programmed WAKE commands in selected
-		 * repurposed TCS to avoid triggering them. tcs->slots will be
-		 * cleaned from rpmh_flush() by invoking rpmh_rsc_invalidate()
-		 */
-		write_tcs_reg_sync(drv, RSC_DRV_CMD_ENABLE, tcs_id, 0);
-		write_tcs_reg_sync(drv, RSC_DRV_CMD_WAIT_FOR_CMPL, tcs_id, 0);
-		enable_tcs_irq(drv, tcs_id, true);
-	}
-	spin_unlock_irqrestore(&drv->lock, flags);
-
-	/*
-	 * These two can be done after the lock is released because:
-	 * - We marked "tcs_in_use" under lock.
-	 * - Once "tcs_in_use" has been marked nobody else could be writing
-	 *   to these registers until the interrupt goes off.
-	 * - The interrupt can't go off until we trigger w/ the last line
-	 *   of __tcs_set_trigger() below.
-	 */
-	__tcs_buffer_write(drv, tcs_id, 0, msg);
-	__tcs_set_trigger(drv, tcs_id, true);
-
-	return 0;
-unlock:
-	spin_unlock_irqrestore(&drv->lock, flags);
 		return ret;
+
+	return find_free_tcs(tcs);
 }
 
 /**
@@ -664,18 +627,47 @@ static int tcs_write(struct rsc_drv *drv, const struct tcs_request *msg)
  */
 int rpmh_rsc_send_data(struct rsc_drv *drv, const struct tcs_request *msg)
 {
-	int ret;
+	struct tcs_group *tcs;
+	int tcs_id;
+	unsigned long flags;
 
-	do {
-		ret = tcs_write(drv, msg);
-		if (ret == -EBUSY) {
-			pr_info_ratelimited("TCS Busy, retrying RPMH message send: addr=%#x\n",
-					    msg->cmds[0].addr);
-			udelay(10);
+	tcs = get_tcs_for_msg(drv, msg);
+	if (IS_ERR(tcs))
+		return PTR_ERR(tcs);
+
+	spin_lock_irqsave(&drv->lock, flags);
+
+	/* Wait forever for a free tcs. It better be there eventually! */
+	wait_event_lock_irq(drv->tcs_wait,
+			    (tcs_id = claim_tcs_for_req(drv, tcs, msg)) >= 0,
+			    drv->lock);
+
+	tcs->req[tcs_id - tcs->offset] = msg;
+	set_bit(tcs_id, drv->tcs_in_use);
+	if (msg->state == RPMH_ACTIVE_ONLY_STATE && tcs->type != ACTIVE_TCS) {
+		/*
+		 * Clear previously programmed WAKE commands in selected
+		 * repurposed TCS to avoid triggering them. tcs->slots will be
+		 * cleaned from rpmh_flush() by invoking rpmh_rsc_invalidate()
+		 */
+		write_tcs_reg_sync(drv, RSC_DRV_CMD_ENABLE, tcs_id, 0);
+		write_tcs_reg_sync(drv, RSC_DRV_CMD_WAIT_FOR_CMPL, tcs_id, 0);
+		enable_tcs_irq(drv, tcs_id, true);
 	}
-	} while (ret == -EBUSY);
+	spin_unlock_irqrestore(&drv->lock, flags);
 
-	return ret;
+	/*
+	 * These two can be done after the lock is released because:
+	 * - We marked "tcs_in_use" under lock.
+	 * - Once "tcs_in_use" has been marked nobody else could be writing
+	 *   to these registers until the interrupt goes off.
+	 * - The interrupt can't go off until we trigger w/ the last line
+	 *   of __tcs_set_trigger() below.
+	 */
+	__tcs_buffer_write(drv, tcs_id, 0, msg);
+	__tcs_set_trigger(drv, tcs_id, true);
+
+	return 0;
 }
 
 /**
@@ -983,6 +975,7 @@ static int rpmh_rsc_probe(struct platform_device *pdev)
 		return ret;
 
 	spin_lock_init(&drv->lock);
+	init_waitqueue_head(&drv->tcs_wait);
 	bitmap_zero(drv->tcs_in_use, MAX_TCS_NR);
 
 	irq = platform_get_irq(pdev, drv->id);

drivers/soc/qcom/socinfo.c

@@ -194,6 +194,7 @@ static const struct soc_id soc_id[] = {
 	{ 186, "MSM8674" },
 	{ 194, "MSM8974PRO" },
 	{ 206, "MSM8916" },
+	{ 207, "MSM8994" },
 	{ 208, "APQ8074-AA" },
 	{ 209, "APQ8074-AB" },
 	{ 210, "APQ8074PRO" },
@@ -214,6 +215,8 @@ static const struct soc_id soc_id[] = {
 	{ 248, "MSM8216" },
 	{ 249, "MSM8116" },
 	{ 250, "MSM8616" },
+	{ 251, "MSM8992" },
+	{ 253, "APQ8094" },
 	{ 291, "APQ8096" },
 	{ 305, "MSM8996SG" },
 	{ 310, "MSM8996AU" },
@@ -223,6 +226,8 @@ static const struct soc_id soc_id[] = {
 	{ 321, "SDM845" },
 	{ 341, "SDA845" },
 	{ 356, "SM8250" },
+	{ 402, "IPQ6018" },
+	{ 425, "SC7180" },
 };
 
 static const char *socinfo_machine(struct device *dev, unsigned int id)

drivers/soc/renesas/Makefile

@@ -24,6 +24,7 @@ obj-$(CONFIG_SYSC_R8A77970)	+= r8a77970-sysc.o
 obj-$(CONFIG_SYSC_R8A77980)	+= r8a77980-sysc.o
 obj-$(CONFIG_SYSC_R8A77990)	+= r8a77990-sysc.o
 obj-$(CONFIG_SYSC_R8A77995)	+= r8a77995-sysc.o
+obj-$(CONFIG_SYSC_R8A779A0)	+= r8a779a0-sysc.o
 ifdef CONFIG_SMP
 obj-$(CONFIG_ARCH_R9A06G032)	+= r9a06g032-smp.o
 endif

drivers/soc/renesas/rcar-rst.c

@@ -37,6 +37,10 @@ static const struct rst_config rcar_rst_gen3 __initconst = {
 	.modemr = 0x60,
 };
 
+static const struct rst_config rcar_rst_r8a779a0 __initconst = {
+	.modemr = 0x00,		/* MODEMR0 and it has CPG related bits */
+};
+
 static const struct of_device_id rcar_rst_matches[] __initconst = {
 	/* RZ/G1 is handled like R-Car Gen2 */
 	{ .compatible = "renesas,r8a7742-rst", .data = &rcar_rst_gen2 },
@@ -67,6 +71,8 @@ static const struct of_device_id rcar_rst_matches[] __initconst = {
 	{ .compatible = "renesas,r8a77980-rst", .data = &rcar_rst_gen3 },
 	{ .compatible = "renesas,r8a77990-rst", .data = &rcar_rst_gen3 },
 	{ .compatible = "renesas,r8a77995-rst", .data = &rcar_rst_gen3 },
+	/* R-Car V3U */
+	{ .compatible = "renesas,r8a779a0-rst", .data = &rcar_rst_r8a779a0 },
 	{ /* sentinel */ }
 };
 

drivers/soc/renesas/renesas-soc.c

@@ -200,6 +200,11 @@ static const struct renesas_soc soc_rcar_d3 __initconst __maybe_unused = {
 	.id	= 0x58,
 };
 
+static const struct renesas_soc soc_rcar_v3u __initconst __maybe_unused = {
+	.family	= &fam_rcar_gen3,
+	.id	= 0x59,
+};
+
 static const struct renesas_soc soc_shmobile_ag5 __initconst __maybe_unused = {
 	.family	= &fam_shmobile,
 	.id	= 0x37,
@@ -291,6 +296,9 @@ static const struct of_device_id renesas_socs[] __initconst = {
 #ifdef CONFIG_ARCH_R8A77995
 	{ .compatible = "renesas,r8a77995",	.data = &soc_rcar_d3 },
 #endif
+#ifdef CONFIG_ARCH_R8A779A0
+	{ .compatible = "renesas,r8a779a0",	.data = &soc_rcar_v3u },
+#endif
 #ifdef CONFIG_ARCH_SH73A0
 	{ .compatible = "renesas,sh73a0",	.data = &soc_shmobile_ag5 },
 #endif

drivers/soc/sunxi/sunxi_sram.c

@@ -194,7 +194,7 @@ static const struct sunxi_sram_data *sunxi_sram_of_parse(struct device_node *nod
 	if (!data) {
 		ret = -EINVAL;
 		goto err;
-	};
+	}
 
 	for (func = data->func; func->func; func++) {
 		if (val == func->val) {

drivers/soc/tegra/fuse/fuse-tegra.c

@@ -49,6 +49,9 @@ static struct tegra_fuse *fuse = &(struct tegra_fuse) {
 };
 
 static const struct of_device_id tegra_fuse_match[] = {
+#ifdef CONFIG_ARCH_TEGRA_234_SOC
+	{ .compatible = "nvidia,tegra234-efuse", .data = &tegra234_fuse_soc },
+#endif
 #ifdef CONFIG_ARCH_TEGRA_194_SOC
 	{ .compatible = "nvidia,tegra194-efuse", .data = &tegra194_fuse_soc },
 #endif
@@ -326,7 +329,8 @@ const struct attribute_group tegra_soc_attr_group = {
 	.attrs = tegra_soc_attr,
 };
 
-#ifdef CONFIG_ARCH_TEGRA_194_SOC
+#if IS_ENABLED(CONFIG_ARCH_TEGRA_194_SOC) || \
+    IS_ENABLED(CONFIG_ARCH_TEGRA_234_SOC)
 static ssize_t platform_show(struct device *dev, struct device_attribute *attr,
 			     char *buf)
 {
@@ -336,7 +340,7 @@ static ssize_t platform_show(struct device *dev, struct device_attribute *attr,
 	 * platform type is silicon and all other non-zero values indicate
 	 * the type of simulation platform is being used.
 	 */
-	return sprintf(buf, "%d\n", (tegra_read_chipid() >> 20) & 0xf);
+	return sprintf(buf, "%d\n", tegra_get_platform());
 }
 
 static DEVICE_ATTR_RO(platform);

drivers/soc/tegra/fuse/fuse-tegra30.c

@@ -356,3 +356,33 @@ const struct tegra_fuse_soc tegra194_fuse_soc = {
 	.soc_attr_group = &tegra194_soc_attr_group,
 };
 #endif
+
+#if defined(CONFIG_ARCH_TEGRA_234_SOC)
+static const struct nvmem_cell_lookup tegra234_fuse_lookups[] = {
+	{
+		.nvmem_name = "fuse",
+		.cell_name = "xusb-pad-calibration",
+		.dev_id = "3520000.padctl",
+		.con_id = "calibration",
+	}, {
+		.nvmem_name = "fuse",
+		.cell_name = "xusb-pad-calibration-ext",
+		.dev_id = "3520000.padctl",
+		.con_id = "calibration-ext",
+	},
+};
+
+static const struct tegra_fuse_info tegra234_fuse_info = {
+	.read = tegra30_fuse_read,
+	.size = 0x300,
+	.spare = 0x280,
+};
+
+const struct tegra_fuse_soc tegra234_fuse_soc = {
+	.init = tegra30_fuse_init,
+	.info = &tegra234_fuse_info,
+	.lookups = tegra234_fuse_lookups,
+	.num_lookups = ARRAY_SIZE(tegra234_fuse_lookups),
+	.soc_attr_group = &tegra194_soc_attr_group,
+};
+#endif

drivers/soc/tegra/fuse/fuse.h

@@ -115,9 +115,17 @@ extern const struct tegra_fuse_soc tegra210_fuse_soc;
 extern const struct tegra_fuse_soc tegra186_fuse_soc;
 #endif
 
+#if IS_ENABLED(CONFIG_ARCH_TEGRA_194_SOC) || \
+    IS_ENABLED(CONFIG_ARCH_TEGRA_234_SOC)
+extern const struct attribute_group tegra194_soc_attr_group;
+#endif
+
 #ifdef CONFIG_ARCH_TEGRA_194_SOC
 extern const struct tegra_fuse_soc tegra194_fuse_soc;
-extern const struct attribute_group tegra194_soc_attr_group;
+#endif
+
+#ifdef CONFIG_ARCH_TEGRA_234_SOC
+extern const struct tegra_fuse_soc tegra234_fuse_soc;
 #endif
 
 #endif

drivers/soc/tegra/fuse/tegra-apbmisc.c

@@ -47,6 +47,31 @@ u8 tegra_get_minor_rev(void)
 	return (tegra_read_chipid() >> 16) & 0xf;
 }
 
+u8 tegra_get_platform(void)
+{
+	return (tegra_read_chipid() >> 20) & 0xf;
+}
+
+bool tegra_is_silicon(void)
+{
+	switch (tegra_get_chip_id()) {
+	case TEGRA194:
+	case TEGRA234:
+		if (tegra_get_platform() == 0)
+			return true;
+
+		return false;
+	}
+
+	/*
+	 * Chips prior to Tegra194 have a different way of determining whether
+	 * they are silicon or not. Since we never supported simulation on the
+	 * older Tegra chips, don't bother extracting the information and just
+	 * report that we're running on silicon.
+	 */
+	return true;
+}
+
 u32 tegra_read_straps(void)
 {
 	WARN(!chipid, "Tegra ABP MISC not yet available\n");
@@ -70,6 +95,7 @@ static const struct of_device_id apbmisc_match[] __initconst = {
 	{ .compatible = "nvidia,tegra20-apbmisc", },
 	{ .compatible = "nvidia,tegra186-misc", },
 	{ .compatible = "nvidia,tegra194-misc", },
+	{ .compatible = "nvidia,tegra234-misc", },
 	{},
 };
 

drivers/soc/ti/Kconfig

@@ -101,6 +101,17 @@ config TI_K3_SOCINFO
 	  platforms to provide information about the SoC family and
 	  variant to user space.
 
+config TI_PRUSS
+	tristate "TI PRU-ICSS Subsystem Platform drivers"
+	depends on SOC_AM33XX || SOC_AM43XX || SOC_DRA7XX || ARCH_KEYSTONE || ARCH_K3
+	select MFD_SYSCON
+	help
+	  TI PRU-ICSS Subsystem platform specific support.
+
+	  Say Y or M here to support the Programmable Realtime Unit (PRU)
+	  processors on various TI SoCs. It's safe to say N here if you're
+	  not interested in the PRU or if you are unsure.
+
 endif # SOC_TI
 
 config TI_SCI_INTA_MSI_DOMAIN

drivers/soc/ti/Makefile

@@ -12,4 +12,5 @@ obj-$(CONFIG_TI_SCI_PM_DOMAINS)		+= ti_sci_pm_domains.o
 obj-$(CONFIG_TI_SCI_INTA_MSI_DOMAIN)	+= ti_sci_inta_msi.o
 obj-$(CONFIG_TI_K3_RINGACC)		+= k3-ringacc.o
 obj-$(CONFIG_TI_K3_SOCINFO)		+= k3-socinfo.o
+obj-$(CONFIG_TI_PRUSS)			+= pruss.o
 obj-$(CONFIG_POWER_AVS_OMAP)		+= smartreflex.o

drivers/soc/ti/k3-ringacc.c

@@ -10,6 +10,7 @@
 #include <linux/init.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
+#include <linux/sys_soc.h>
 #include <linux/soc/ti/k3-ringacc.h>
 #include <linux/soc/ti/ti_sci_protocol.h>
 #include <linux/soc/ti/ti_sci_inta_msi.h>
@@ -208,6 +209,15 @@ struct k3_ringacc {
 	const struct k3_ringacc_ops *ops;
 };
 
+/**
+ * struct k3_ringacc - Rings accelerator SoC data
+ *
+ * @dma_ring_reset_quirk:  DMA reset w/a enable
+ */
+struct k3_ringacc_soc_data {
+	unsigned dma_ring_reset_quirk:1;
+};
+
 static long k3_ringacc_ring_get_fifo_pos(struct k3_ring *ring)
 {
 	return K3_RINGACC_FIFO_WINDOW_SIZE_BYTES -
@@ -1051,9 +1061,6 @@ static int k3_ringacc_probe_dt(struct k3_ringacc *ringacc)
 		return ret;
 	}
 
-	ringacc->dma_ring_reset_quirk =
-			of_property_read_bool(node, "ti,dma-ring-reset-quirk");
-
 	ringacc->tisci = ti_sci_get_by_phandle(node, "ti,sci");
 	if (IS_ERR(ringacc->tisci)) {
 		ret = PTR_ERR(ringacc->tisci);
@@ -1084,9 +1091,22 @@ static int k3_ringacc_probe_dt(struct k3_ringacc *ringacc)
 						 ringacc->rm_gp_range);
 }
 
+static const struct k3_ringacc_soc_data k3_ringacc_soc_data_sr1 = {
+	.dma_ring_reset_quirk = 1,
+};
+
+static const struct soc_device_attribute k3_ringacc_socinfo[] = {
+	{ .family = "AM65X",
+	  .revision = "SR1.0",
+	  .data = &k3_ringacc_soc_data_sr1
+	},
+	{/* sentinel */}
+};
+
 static int k3_ringacc_init(struct platform_device *pdev,
 			   struct k3_ringacc *ringacc)
 {
+	const struct soc_device_attribute *soc;
 	void __iomem *base_fifo, *base_rt;
 	struct device *dev = &pdev->dev;
 	struct resource *res;
@@ -1103,6 +1123,13 @@ static int k3_ringacc_init(struct platform_device *pdev,
 	if (ret)
 		return ret;
 
+	soc = soc_device_match(k3_ringacc_socinfo);
+	if (soc && soc->data) {
+		const struct k3_ringacc_soc_data *soc_data = soc->data;
+
+		ringacc->dma_ring_reset_quirk = soc_data->dma_ring_reset_quirk;
+	}
+
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rt");
 	base_rt = devm_ioremap_resource(dev, res);
 	if (IS_ERR(base_rt))

drivers/soc/ti/k3-socinfo.c

@@ -39,6 +39,7 @@ static const struct k3_soc_id {
 } k3_soc_ids[] = {
 	{ 0xBB5A, "AM65X" },
 	{ 0xBB64, "J721E" },
+	{ 0xBB6D, "J7200" },
 };
 
 static int

drivers/tee/optee/optee_private.h

@@ -17,6 +17,7 @@
 /* Some Global Platform error codes used in this driver */
 #define TEEC_SUCCESS			0x00000000
 #define TEEC_ERROR_BAD_PARAMETERS	0xFFFF0006
+#define TEEC_ERROR_NOT_SUPPORTED	0xFFFF000A
 #define TEEC_ERROR_COMMUNICATION	0xFFFF000E
 #define TEEC_ERROR_OUT_OF_MEMORY	0xFFFF000C
 #define TEEC_ERROR_SHORT_BUFFER		0xFFFF0010