Commit 3bd271cd authored by Martin Dalecki's avatar Martin Dalecki Committed by Jeff Garzik

[PATCH] 2.5.29 IDE 108

 - typedef unsigned char byte; is finally gone. Everything using it should
   be just ported to u8 if I missed some place where it still gets used.

 - Next round of parameter parsing cleanups by Gerald Champagne.
   Adjusted a bit to harmonize with  hd.c.

 - Move IDE register bitfields declarations over from hdparm.h to
   ide.h.

 - Declare constants needed by hd.c directly there. Those are standard
   values not subject to change and we prefer a bit of code duplication
   in favour of making the two drivers independant from each other.

 - Move everything not ioctl related away from hdreg.h to ide.h.
   This header is in effect not private to the ATA code and should
   therefore not contain stuff only usefull there.
parent 12949f5d
/* /*
* linux/drivers/ide/hd.c
*
* Copyright (C) 1991, 1992 Linus Torvalds * Copyright (C) 1991, 1992 Linus Torvalds
*/ *
/*
* This is the low-level hd interrupt support. It traverses the * This is the low-level hd interrupt support. It traverses the
* request-list, using interrupts to jump between functions. As * request-list, using interrupts to jump between functions. As
* all the functions are called within interrupts, we may not * all the functions are called within interrupts, we may not
...@@ -37,7 +33,6 @@ ...@@ -37,7 +33,6 @@
#include <linux/fs.h> #include <linux/fs.h>
#include <linux/devfs_fs_kernel.h> #include <linux/devfs_fs_kernel.h>
#include <linux/kernel.h> #include <linux/kernel.h>
#include <linux/hdreg.h>
#include <linux/genhd.h> #include <linux/genhd.h>
#include <linux/slab.h> #include <linux/slab.h>
#include <linux/string.h> #include <linux/string.h>
...@@ -45,6 +40,7 @@ ...@@ -45,6 +40,7 @@
#include <linux/mc146818rtc.h> /* CMOS defines */ #include <linux/mc146818rtc.h> /* CMOS defines */
#include <linux/init.h> #include <linux/init.h>
#include <linux/blkpg.h> #include <linux/blkpg.h>
#include <linux/hdreg.h>
#define REALLY_SLOW_IO #define REALLY_SLOW_IO
#include <asm/system.h> #include <asm/system.h>
...@@ -55,6 +51,15 @@ ...@@ -55,6 +51,15 @@
#define DEVICE_NR(device) (minor(device)>>6) #define DEVICE_NR(device) (minor(device)>>6)
#include <linux/blk.h> #include <linux/blk.h>
/* ATA commands we use.
*/
#define WIN_SPECIFY 0x91 /* set drive geometry translation */
#define WIN_RESTORE 0x10
#define WIN_READ 0x20 /* 28-Bit */
#define WIN_WRITE 0x30 /* 28-Bit */
#define HD_IRQ 14 /* the standard disk interrupt */
#ifdef __arm__ #ifdef __arm__
#undef HD_IRQ #undef HD_IRQ
#endif #endif
...@@ -63,6 +68,45 @@ ...@@ -63,6 +68,45 @@
#define HD_IRQ IRQ_HARDDISK #define HD_IRQ IRQ_HARDDISK
#endif #endif
/* Hd controller regster ports */
#define HD_DATA 0x1f0 /* _CTL when writing */
#define HD_ERROR 0x1f1 /* see err-bits */
#define HD_NSECTOR 0x1f2 /* nr of sectors to read/write */
#define HD_SECTOR 0x1f3 /* starting sector */
#define HD_LCYL 0x1f4 /* starting cylinder */
#define HD_HCYL 0x1f5 /* high byte of starting cyl */
#define HD_CURRENT 0x1f6 /* 101dhhhh , d=drive, hhhh=head */
#define HD_STATUS 0x1f7 /* see status-bits */
#define HD_FEATURE HD_ERROR /* same io address, read=error, write=feature */
#define HD_PRECOMP HD_FEATURE /* obsolete use of this port - predates IDE */
#define HD_COMMAND HD_STATUS /* same io address, read=status, write=cmd */
#define HD_CMD 0x3f6 /* used for resets */
#define HD_ALTSTATUS 0x3f6 /* same as HD_STATUS but doesn't clear irq */
/* Bits of HD_STATUS */
#define ERR_STAT 0x01
#define INDEX_STAT 0x02
#define ECC_STAT 0x04 /* Corrected error */
#define DRQ_STAT 0x08
#define SEEK_STAT 0x10
#define SERVICE_STAT SEEK_STAT
#define WRERR_STAT 0x20
#define READY_STAT 0x40
#define BUSY_STAT 0x80
/* Bits for HD_ERROR */
#define MARK_ERR 0x01 /* Bad address mark */
#define TRK0_ERR 0x02 /* couldn't find track 0 */
#define ABRT_ERR 0x04 /* Command aborted */
#define MCR_ERR 0x08 /* media change request */
#define ID_ERR 0x10 /* ID field not found */
#define MC_ERR 0x20 /* media changed */
#define ECC_ERR 0x40 /* Uncorrectable ECC error */
#define BBD_ERR 0x80 /* pre-EIDE meaning: block marked bad */
#define ICRC_ERR 0x80 /* new meaning: CRC error during transfer */
static spinlock_t hd_lock = SPIN_LOCK_UNLOCKED; static spinlock_t hd_lock = SPIN_LOCK_UNLOCKED;
static int revalidate_hddisk(kdev_t, int); static int revalidate_hddisk(kdev_t, int);
...@@ -162,12 +206,9 @@ void __init hd_setup(char *str, int *ints) ...@@ -162,12 +206,9 @@ void __init hd_setup(char *str, int *ints)
static void dump_status (const char *msg, unsigned int stat) static void dump_status (const char *msg, unsigned int stat)
{ {
unsigned long flags;
char devc; char devc;
devc = !blk_queue_empty(QUEUE) ? 'a' + DEVICE_NR(CURRENT->rq_dev) : '?'; devc = !blk_queue_empty(QUEUE) ? 'a' + DEVICE_NR(CURRENT->rq_dev) : '?';
save_flags (flags);
sti();
#ifdef VERBOSE_ERRORS #ifdef VERBOSE_ERRORS
printk("hd%c: %s: status=0x%02x { ", devc, msg, stat & 0xff); printk("hd%c: %s: status=0x%02x { ", devc, msg, stat & 0xff);
if (stat & BUSY_STAT) printk("Busy "); if (stat & BUSY_STAT) printk("Busy ");
...@@ -207,8 +248,7 @@ static void dump_status (const char *msg, unsigned int stat) ...@@ -207,8 +248,7 @@ static void dump_status (const char *msg, unsigned int stat)
hd_error = inb(HD_ERROR); hd_error = inb(HD_ERROR);
printk("hd%c: %s: error=0x%02x.\n", devc, msg, hd_error & 0xff); printk("hd%c: %s: error=0x%02x.\n", devc, msg, hd_error & 0xff);
} }
#endif /* verbose errors */ #endif
restore_flags (flags);
} }
void check_status(void) void check_status(void)
...@@ -467,7 +507,7 @@ static void write_intr(void) ...@@ -467,7 +507,7 @@ static void write_intr(void)
if (i > 0) { if (i > 0) {
SET_HANDLER(&write_intr); SET_HANDLER(&write_intr);
outsw(HD_DATA,CURRENT->buffer,256); outsw(HD_DATA,CURRENT->buffer,256);
sti(); local_irq_enable();
} else { } else {
#if (HD_DELAY > 0) #if (HD_DELAY > 0)
last_req = read_timer(); last_req = read_timer();
...@@ -500,7 +540,7 @@ static void hd_times_out(unsigned long dummy) ...@@ -500,7 +540,7 @@ static void hd_times_out(unsigned long dummy)
return; return;
disable_irq(HD_IRQ); disable_irq(HD_IRQ);
sti(); local_irq_enable();
reset = 1; reset = 1;
dev = DEVICE_NR(CURRENT->rq_dev); dev = DEVICE_NR(CURRENT->rq_dev);
printk("hd%c: timeout\n", dev+'a'); printk("hd%c: timeout\n", dev+'a');
...@@ -510,7 +550,7 @@ static void hd_times_out(unsigned long dummy) ...@@ -510,7 +550,7 @@ static void hd_times_out(unsigned long dummy)
#endif #endif
end_request(CURRENT, 0); end_request(CURRENT, 0);
} }
cli(); local_irq_disable();
hd_request(); hd_request();
enable_irq(HD_IRQ); enable_irq(HD_IRQ);
} }
...@@ -548,7 +588,7 @@ static void hd_request(void) ...@@ -548,7 +588,7 @@ static void hd_request(void)
return; return;
repeat: repeat:
del_timer(&device_timer); del_timer(&device_timer);
sti(); local_irq_enable();
if (blk_queue_empty(QUEUE)) { if (blk_queue_empty(QUEUE)) {
do_hd = NULL; do_hd = NULL;
...@@ -556,7 +596,7 @@ static void hd_request(void) ...@@ -556,7 +596,7 @@ static void hd_request(void)
} }
if (reset) { if (reset) {
cli(); local_irq_disable();
reset_hd(); reset_hd();
return; return;
} }
...@@ -688,7 +728,7 @@ static void hd_interrupt(int irq, void *dev_id, struct pt_regs *regs) ...@@ -688,7 +728,7 @@ static void hd_interrupt(int irq, void *dev_id, struct pt_regs *regs)
if (!handler) if (!handler)
handler = unexpected_hd_interrupt; handler = unexpected_hd_interrupt;
handler(); handler();
sti(); local_irq_enable();
} }
static struct block_device_operations hd_fops = { static struct block_device_operations hd_fops = {
......
...@@ -305,8 +305,9 @@ ...@@ -305,8 +305,9 @@
#include <linux/interrupt.h> #include <linux/interrupt.h>
#include <linux/errno.h> #include <linux/errno.h>
#include <linux/cdrom.h> #include <linux/cdrom.h>
#include <linux/ide.h>
#include <linux/completion.h> #include <linux/completion.h>
#include <linux/hdreg.h>
#include <linux/ide.h>
#include <asm/irq.h> #include <asm/irq.h>
#include <asm/io.h> #include <asm/io.h>
......
...@@ -94,9 +94,10 @@ ...@@ -94,9 +94,10 @@
#include <linux/genhd.h> #include <linux/genhd.h>
#include <linux/slab.h> #include <linux/slab.h>
#include <linux/cdrom.h> #include <linux/cdrom.h>
#include <linux/buffer_head.h>
#include <linux/hdreg.h>
#include <linux/ide.h> #include <linux/ide.h>
#include <linux/atapi.h> #include <linux/atapi.h>
#include <linux/buffer_head.h>
#include <asm/byteorder.h> #include <asm/byteorder.h>
#include <asm/irq.h> #include <asm/irq.h>
......
...@@ -550,7 +550,8 @@ static void __init hpt374_device_order_fixup (struct pci_dev *dev, struct ata_pc ...@@ -550,7 +550,8 @@ static void __init hpt374_device_order_fixup (struct pci_dev *dev, struct ata_pc
if (!dev2) { if (!dev2) {
return; return;
} else { } else {
byte irq = 0, irq2 = 0; u8 irq = 0;
u8 irq2 = 0;
pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq); pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq);
pci_read_config_byte(dev2, PCI_INTERRUPT_LINE, &irq2); pci_read_config_byte(dev2, PCI_INTERRUPT_LINE, &irq2);
if (irq != irq2) { if (irq != irq2) {
......
...@@ -419,9 +419,10 @@ ...@@ -419,9 +419,10 @@
#include <linux/pci.h> #include <linux/pci.h>
#include <linux/smp_lock.h> #include <linux/smp_lock.h>
#include <linux/completion.h> #include <linux/completion.h>
#include <linux/buffer_head.h>
#include <linux/hdreg.h>
#include <linux/ide.h> #include <linux/ide.h>
#include <linux/atapi.h> #include <linux/atapi.h>
#include <linux/buffer_head.h>
#include <asm/byteorder.h> #include <asm/byteorder.h>
#include <asm/irq.h> #include <asm/irq.h>
...@@ -1249,7 +1250,7 @@ char *idetape_sense_key_verbose(u8 idetape_sense_key) ...@@ -1249,7 +1250,7 @@ char *idetape_sense_key_verbose(u8 idetape_sense_key)
} }
} }
char *idetape_command_key_verbose (byte idetape_command_key) char *idetape_command_key_verbose(u8 idetape_command_key)
{ {
switch (idetape_command_key) { switch (idetape_command_key) {
case IDETAPE_TEST_UNIT_READY_CMD: return("TEST_UNIT_READY_CMD"); case IDETAPE_TEST_UNIT_READY_CMD: return("TEST_UNIT_READY_CMD");
...@@ -1439,7 +1440,7 @@ static void idetape_analyze_error(struct ata_device *drive, atapi_request_sense_ ...@@ -1439,7 +1440,7 @@ static void idetape_analyze_error(struct ata_device *drive, atapi_request_sense_
# if IDETAPE_DEBUG_LOG_VERBOSE # if IDETAPE_DEBUG_LOG_VERBOSE
if (tape->debug_level >= 1) if (tape->debug_level >= 1)
printk (KERN_INFO "ide-tape: pc = %s, sense key = %x, asc = %x, ascq = %x\n", printk (KERN_INFO "ide-tape: pc = %s, sense key = %x, asc = %x, ascq = %x\n",
idetape_command_key_verbose((byte) pc->c[0]), idetape_command_key_verbose(pc->c[0]),
result->sense_key, result->sense_key,
result->asc, result->asc,
result->ascq); result->ascq);
...@@ -2166,7 +2167,7 @@ static void idetape_pc_callback(struct ata_device *drive, struct request *rq) ...@@ -2166,7 +2167,7 @@ static void idetape_pc_callback(struct ata_device *drive, struct request *rq)
/* /*
* A mode sense command is used to "sense" tape parameters. * A mode sense command is used to "sense" tape parameters.
*/ */
static void idetape_create_mode_sense_cmd(struct atapi_packet_command *pc, byte page_code) static void idetape_create_mode_sense_cmd(struct atapi_packet_command *pc, u8 page_code)
{ {
atapi_init_pc(pc); atapi_init_pc(pc);
pc->c[0] = IDETAPE_MODE_SENSE_CMD; pc->c[0] = IDETAPE_MODE_SENSE_CMD;
...@@ -3225,7 +3226,7 @@ static int __idetape_discard_read_pipeline(struct ata_device *drive) ...@@ -3225,7 +3226,7 @@ static int __idetape_discard_read_pipeline(struct ata_device *drive)
* of the request queue and wait for their completion. * of the request queue and wait for their completion.
* *
*/ */
static int idetape_position_tape(struct ata_device *drive, unsigned int block, byte partition, int skip) static int idetape_position_tape(struct ata_device *drive, unsigned int block, u8 partition, int skip)
{ {
idetape_tape_t *tape = drive->driver_data; idetape_tape_t *tape = drive->driver_data;
int retval; int retval;
...@@ -3981,7 +3982,7 @@ static int idetape_add_chrdev_read_request(struct ata_device *drive,int blocks) ...@@ -3981,7 +3982,7 @@ static int idetape_add_chrdev_read_request(struct ata_device *drive,int blocks)
printk (KERN_ERR "ide-tape: bug: trying to return more bytes than requested\n"); printk (KERN_ERR "ide-tape: bug: trying to return more bytes than requested\n");
bytes_read=blocks*tape->tape_block_size; bytes_read=blocks*tape->tape_block_size;
} }
#endif /* IDETAPE_DEBUG_BUGS */ #endif
return (bytes_read); return (bytes_read);
} }
......
...@@ -33,6 +33,15 @@ ...@@ -33,6 +33,15 @@
#include "ioctl.h" #include "ioctl.h"
/* BIG GEOMETRY - dying, used only by HDIO_GETGEO_BIG_RAW */
struct hd_big_geometry {
u8 heads;
u8 sectors;
u32 cylinders;
unsigned long start;
};
/* /*
* Implement generic ioctls invoked from userspace to imlpement specific * Implement generic ioctls invoked from userspace to imlpement specific
* functionality. * functionality.
......
...@@ -191,7 +191,11 @@ static void init_hwif_data(struct ata_channel *ch, unsigned int index) ...@@ -191,7 +191,11 @@ static void init_hwif_data(struct ata_channel *ch, unsigned int index)
ch->noprobe = !ch->io_ports[IDE_DATA_OFFSET]; ch->noprobe = !ch->io_ports[IDE_DATA_OFFSET];
#ifdef CONFIG_BLK_DEV_HD #ifdef CONFIG_BLK_DEV_HD
if (ch->io_ports[IDE_DATA_OFFSET] == HD_DATA)
/* Ignore disks for which handling by the legacy driver was requested
* by the used.
*/
if (ch->io_ports[IDE_DATA_OFFSET] == 0x1f0)
ch->noprobe = 1; /* may be overridden by ide_setup() */ ch->noprobe = 1; /* may be overridden by ide_setup() */
#endif #endif
...@@ -701,79 +705,46 @@ static void __init init_global_data(void) ...@@ -701,79 +705,46 @@ static void __init init_global_data(void)
/* /*
* This gets called VERY EARLY during initialization, to handle kernel "command * This gets called VERY EARLY during initialization, to handle kernel "command
* line" strings beginning with "hdx=" or "ide".It gets called even before the * line" strings beginning with "hdx=". It gets called even before the actual
* actual module gets initialized. * module gets initialized.
* *
* Please look at Documentation/ide.txt to see the complete list of supported * Please look at Documentation/ide.txt to see the complete list of supported
* options. * options.
*/ */
int __init ide_setup(char *s) static int __init ata_hd_setup(char *s)
{ {
int i, vals[4]; int vals[4];
struct ata_channel *ch; struct ata_channel *ch; /* FIXME: Channel parms should not be accessed in ata_hd_setup */
struct ata_device *drive; struct ata_device *drive;
unsigned int hw, unit; unsigned int hw, unit;
const char max_drive = 'a' + ((MAX_HWIFS * MAX_DRIVES) - 1); const char max_drive = 'a' + ((MAX_HWIFS * MAX_DRIVES) - 1);
const char max_ch = '0' + (MAX_HWIFS - 1);
if (!strncmp(s, "hd=", 3)) /* hd= is for hd.c driver and not us */ if (s[0] == '=') /* hd= is for hd.c driver and not us */
return 0; return 0;
if (strncmp(s,"ide",3) && printk(KERN_INFO "hd%s", s);
strncmp(s,"hd",2)) /* hdx= & hdxlun= */
return 0;
printk(KERN_INFO "ide_setup: %s", s);
init_global_data(); init_global_data();
#ifdef CONFIG_BLK_DEV_IDEDOUBLER if (s[0] >= 'a' && s[0] <= max_drive) {
if (!strcmp(s, "ide=doubler")) { static const char *hd_words[] = {"none", "noprobe", "nowerr", "cdrom",
extern int ide_doubler;
printk(KERN_INFO" : Enabled support for IDE doublers\n");
ide_doubler = 1;
return 1;
}
#endif
if (!strcmp(s, "ide=nodma")) {
printk(KERN_INFO "ATA: Prevented DMA\n");
noautodma = 1;
return 1;
}
#ifdef CONFIG_PCI
if (!strcmp(s, "ide=reverse")) {
ide_scan_direction = 1;
printk(" : Enabled support for IDE inverse scan order.\n");
return 1;
}
#endif
/*
* Look for drive options: "hdx="
*/
if (!strncmp(s, "hd", 2) && s[2] >= 'a' && s[2] <= max_drive) {
const char *hd_words[] = {"none", "noprobe", "nowerr", "cdrom",
"serialize", "autotune", "noautotune", "serialize", "autotune", "noautotune",
"slow", "flash", "remap", "noremap", "scsi", NULL}; "slow", "flash", "remap", "noremap", "scsi", NULL};
unit = s[2] - 'a'; unit = s[0] - 'a';
hw = unit / MAX_DRIVES; hw = unit / MAX_DRIVES;
unit = unit % MAX_DRIVES; unit = unit % MAX_DRIVES;
ch = &ide_hwifs[hw]; ch = &ide_hwifs[hw];
drive = &ch->drives[unit]; drive = &ch->drives[unit];
if (!strncmp(s+3, "=ide-", 5)) {
strncpy(drive->driver_req, s + 4, 9); /* Look for hdx=ide-* */
if (!strncmp(s+1, "=ide-", 5)) {
strncpy(drive->driver_req, s+2, 9);
goto done; goto done;
} }
/* /*
* Look for last lun option: "hdxlun=" * Look for last lun option: "hdxlun="
*/ */
if (!strncmp(s+3, "lun=", 4)) { if (!strncmp(s+1, "lun=", 4)) {
if (*get_options(s+7, 2, vals) || vals[0]!=1) if (*get_options(s+5, 2, vals) || vals[0]!=1)
goto bad_option; goto bad_option;
if (vals[1] >= 0 && vals[1] <= 7) { if (vals[1] >= 0 && vals[1] <= 7) {
drive->last_lun = vals[1]; drive->last_lun = vals[1];
...@@ -782,7 +753,7 @@ int __init ide_setup(char *s) ...@@ -782,7 +753,7 @@ int __init ide_setup(char *s)
printk(" -- BAD LAST LUN! Expected value from 0 to 7"); printk(" -- BAD LAST LUN! Expected value from 0 to 7");
goto done; goto done;
} }
switch (match_parm(s+3, hd_words, vals, 3)) { switch (match_parm(s+1, hd_words, vals, 3)) {
case -1: /* "none" */ case -1: /* "none" */
drive->nobios = 1; /* drop into "noprobe" */ drive->nobios = 1; /* drop into "noprobe" */
case -2: /* "noprobe" */ case -2: /* "noprobe" */
...@@ -790,16 +761,16 @@ int __init ide_setup(char *s) ...@@ -790,16 +761,16 @@ int __init ide_setup(char *s)
goto done; goto done;
case -3: /* "nowerr" */ case -3: /* "nowerr" */
drive->bad_wstat = BAD_R_STAT; drive->bad_wstat = BAD_R_STAT;
ch->noprobe = 0; ch->noprobe = 0; /* FIXME: Channel parm */
goto done; goto done;
case -4: /* "cdrom" */ case -4: /* "cdrom" */
drive->present = 1; drive->present = 1;
drive->type = ATA_ROM; drive->type = ATA_ROM;
ch->noprobe = 0; ch->noprobe = 0; /* FIXME: Channel parm */
goto done; goto done;
case -5: /* "serialize" */ case -5: /* "serialize" */
printk(" -- USE \"ide%d=serialize\" INSTEAD", hw); printk(" -- USE \"ide%d=serialize\" INSTEAD", hw);
goto do_serialize; goto bad_option;
case -6: /* "autotune" */ case -6: /* "autotune" */
drive->autotune = 1; drive->autotune = 1;
goto done; goto done;
...@@ -807,7 +778,7 @@ int __init ide_setup(char *s) ...@@ -807,7 +778,7 @@ int __init ide_setup(char *s)
drive->autotune = 2; drive->autotune = 2;
goto done; goto done;
case -8: /* "slow" */ case -8: /* "slow" */
ch->slow = 1; ch->slow = 1; /* FIXME: Channel parm */
goto done; goto done;
case -9: /* "flash" */ case -9: /* "flash" */
drive->ata_flash = 1; drive->ata_flash = 1;
...@@ -840,11 +811,63 @@ int __init ide_setup(char *s) ...@@ -840,11 +811,63 @@ int __init ide_setup(char *s)
} }
} }
bad_option:
printk(" -- BAD OPTION\n");
return 1;
done:
printk("\n");
return 1;
}
/*
* This gets called VERY EARLY during initialization, to handle kernel "command
* line" strings beginning with "ide". It gets called even before the actual
* module gets initialized.
*
* Please look at Documentation/ide.txt to see the complete list of supported
* options.
*/
int __init ide_setup(char *s)
{
int i, vals[4];
struct ata_channel *ch;
unsigned int hw;
const char max_ch = '0' + (MAX_HWIFS - 1);
printk(KERN_INFO "ide_setup: ide%s", s);
init_global_data();
#ifdef CONFIG_BLK_DEV_IDEDOUBLER
if (!strcmp(s, "=doubler")) {
extern int ide_doubler;
printk(KERN_INFO" : Enabled support for IDE doublers\n");
ide_doubler = 1;
return 1;
}
#endif
if (!strcmp(s, "=nodma")) {
printk(KERN_INFO "ATA: Prevented DMA\n");
noautodma = 1;
return 1;
}
#ifdef CONFIG_PCI
if (!strcmp(s, "=reverse")) {
ide_scan_direction = 1;
printk(" : Enabled support for IDE inverse scan order.\n");
return 1;
}
#endif
/* /*
* Look for bus speed option: "idebus=" * Look for bus speed option: "idebus="
*/ */
if (!strncmp(s, "idebus=", 7)) { if (!strncmp(s, "bus=", 4)) {
if (*get_options(s+7, 2, vals) || vals[0] != 1) if (*get_options(s+4, 2, vals) || vals[0] != 1)
goto bad_option; goto bad_option;
idebus_parameter = vals[1]; idebus_parameter = vals[1];
goto done; goto done;
...@@ -853,7 +876,7 @@ int __init ide_setup(char *s) ...@@ -853,7 +876,7 @@ int __init ide_setup(char *s)
/* /*
* Look for interface options: "idex=" * Look for interface options: "idex="
*/ */
if (!strncmp(s, "ide", 3) && s[3] >= '0' && s[3] <= max_ch) { if (s[0] >= '0' && s[0] <= max_ch) {
/* /*
* Be VERY CAREFUL changing this: note hardcoded indexes below * Be VERY CAREFUL changing this: note hardcoded indexes below
*/ */
...@@ -861,11 +884,11 @@ int __init ide_setup(char *s) ...@@ -861,11 +884,11 @@ int __init ide_setup(char *s)
"noprobe", "serialize", "autotune", "noautotune", "reset", "dma", "ata66", NULL }; "noprobe", "serialize", "autotune", "noautotune", "reset", "dma", "ata66", NULL };
const char *ide_words[] = { const char *ide_words[] = {
"qd65xx", "ht6560b", "cmd640_vlb", "dtc2278", "umc8672", "ali14xx", "dc4030", NULL }; "qd65xx", "ht6560b", "cmd640_vlb", "dtc2278", "umc8672", "ali14xx", "dc4030", NULL };
hw = s[3] - '0'; hw = s[0] - '0';
ch = &ide_hwifs[hw]; ch = &ide_hwifs[hw];
switch (match_parm(s+4, ide_options, vals, 1)) { switch (match_parm(s+1, ide_options, vals, 1)) {
case -7: /* ata66 */ case -7: /* ata66 */
#ifdef CONFIG_PCI #ifdef CONFIG_PCI
ch->udma_four = 1; ch->udma_four = 1;
...@@ -889,7 +912,6 @@ int __init ide_setup(char *s) ...@@ -889,7 +912,6 @@ int __init ide_setup(char *s)
ch->drives[1].autotune = 1; ch->drives[1].autotune = 1;
goto done; goto done;
case -2: /* "serialize" */ case -2: /* "serialize" */
do_serialize:
{ {
struct ata_channel *mate; struct ata_channel *mate;
...@@ -904,7 +926,10 @@ int __init ide_setup(char *s) ...@@ -904,7 +926,10 @@ int __init ide_setup(char *s)
goto done; goto done;
} }
i = match_parm(&s[4], ide_words, vals, 3); /*
* Check for specific chipset name
*/
i = match_parm(s+1, ide_words, vals, 3);
/* /*
* Cryptic check to ensure chipset not already set for a channel: * Cryptic check to ensure chipset not already set for a channel:
...@@ -1432,9 +1457,15 @@ static int __init init_ata(void) ...@@ -1432,9 +1457,15 @@ static int __init init_ata(void)
while ((options = next) != NULL) { while ((options = next) != NULL) {
if ((next = strchr(options,' ')) != NULL) if ((next = strchr(options,' ')) != NULL)
*next++ = 0; *next++ = 0;
if (!ide_setup(options)) if (!strncmp(options,"hd",2)) {
if (!ata_hd_setup(options+2))
printk(KERN_ERR "Unknown option '%s'\n", options); printk(KERN_ERR "Unknown option '%s'\n", options);
} }
else if (!strncmp(options,"ide",3)) {
if (!ide_setup(options+3))
printk(KERN_ERR "Unknown option '%s'\n", options);
}
}
} }
return ata_module_init(); return ata_module_init();
} }
...@@ -1457,6 +1488,7 @@ module_exit(cleanup_ata); ...@@ -1457,6 +1488,7 @@ module_exit(cleanup_ata);
#ifndef MODULE #ifndef MODULE
/* command line option parser */ /* command line option parser */
__setup("", ide_setup); __setup("ide", ide_setup);
__setup("hd", ata_hd_setup);
#endif #endif
...@@ -1082,7 +1082,12 @@ static void channel_init(struct ata_channel *ch) ...@@ -1082,7 +1082,12 @@ static void channel_init(struct ata_channel *ch)
} }
} }
#ifdef CONFIG_BLK_DEV_HD #ifdef CONFIG_BLK_DEV_HD
if (ch->irq == HD_IRQ && ch->io_ports[IDE_DATA_OFFSET] != HD_DATA) {
/* The first "legacy" HD gets distinguished by the IRQ it is attached
* to and the IO port it takes.
*/
if (ch->irq == 14 && ch->io_ports[IDE_DATA_OFFSET] != 0x1f0) {
printk("%s: CANNOT SHARE IRQ WITH OLD HARDDISK DRIVER (hd.c)\n", ch->name); printk("%s: CANNOT SHARE IRQ WITH OLD HARDDISK DRIVER (hd.c)\n", ch->name);
return; return;
......
...@@ -40,43 +40,47 @@ ...@@ -40,43 +40,47 @@
static void pdump (void *, int); static void pdump (void *, int);
#endif #endif
/* Bits of HD_STATUS */
#define ERR_STAT 0x01
#define DRQ_STAT 0x08
struct freecom_udata { struct freecom_udata {
__u8 buffer[64]; /* Common command block. */ u8 buffer[64]; /* Common command block. */
}; };
typedef struct freecom_udata *freecom_udata_t; typedef struct freecom_udata *freecom_udata_t;
/* All of the outgoing packets are 64 bytes long. */ /* All of the outgoing packets are 64 bytes long. */
struct freecom_cb_wrap { struct freecom_cb_wrap {
__u8 Type; /* Command type. */ u8 Type; /* Command type. */
__u8 Timeout; /* Timeout in seconds. */ u8 Timeout; /* Timeout in seconds. */
__u8 Atapi[12]; /* An ATAPI packet. */ u8 Atapi[12]; /* An ATAPI packet. */
__u8 Filler[50]; /* Padding Data. */ u8 Filler[50]; /* Padding Data. */
}; };
struct freecom_xfer_wrap { struct freecom_xfer_wrap {
__u8 Type; /* Command type. */ u8 Type; /* Command type. */
__u8 Timeout; /* Timeout in seconds. */ u8 Timeout; /* Timeout in seconds. */
__u32 Count; /* Number of bytes to transfer. */ u32 Count; /* Number of bytes to transfer. */
__u8 Pad[58]; u8 Pad[58];
} __attribute__ ((packed)); } __attribute__ ((packed));
struct freecom_ide_out { struct freecom_ide_out {
__u8 Type; /* Type + IDE register. */ u8 Type; /* Type + IDE register. */
__u8 Pad; u8 Pad;
__u16 Value; /* Value to write. */ u16 Value; /* Value to write. */
__u8 Pad2[60]; u8 Pad2[60];
}; };
struct freecom_ide_in { struct freecom_ide_in {
__u8 Type; /* Type | IDE register. */ u8 Type; /* Type | IDE register. */
__u8 Pad[63]; u8 Pad[63];
}; };
struct freecom_status { struct freecom_status {
__u8 Status; u8 Status;
__u8 Reason; u8 Reason;
__u16 Count; u16 Count;
__u8 Pad[60]; u8 Pad[60];
}; };
/* Freecom stuffs the interrupt status in the INDEX_STAT bit of the ide /* Freecom stuffs the interrupt status in the INDEX_STAT bit of the ide
......
#ifndef _LINUX_HDREG_H #ifndef _LINUX_HDREG_H
#define _LINUX_HDREG_H #define _LINUX_HDREG_H
/*
* This file contains some defines for the AT-hd-controller.
* Various sources.
*/
#define HD_IRQ 14 /* the standard disk interrupt */
/* ide.c has its own port definitions in "ide.h" */
/* Hd controller regs. Ref: IBM AT Bios-listing */
#define HD_DATA 0x1f0 /* _CTL when writing */
#define HD_ERROR 0x1f1 /* see err-bits */
#define HD_NSECTOR 0x1f2 /* nr of sectors to read/write */
#define HD_SECTOR 0x1f3 /* starting sector */
#define HD_LCYL 0x1f4 /* starting cylinder */
#define HD_HCYL 0x1f5 /* high byte of starting cyl */
#define HD_CURRENT 0x1f6 /* 101dhhhh , d=drive, hhhh=head */
#define HD_STATUS 0x1f7 /* see status-bits */
#define HD_FEATURE HD_ERROR /* same io address, read=error, write=feature */
#define HD_PRECOMP HD_FEATURE /* obsolete use of this port - predates IDE */
#define HD_COMMAND HD_STATUS /* same io address, read=status, write=cmd */
#define HD_CMD 0x3f6 /* used for resets */
#define HD_ALTSTATUS 0x3f6 /* same as HD_STATUS but doesn't clear irq */
/* remainder is shared between hd.c, ide.c, ide-cd.c, and the hdparm utility */
/* Bits of HD_STATUS */
#define ERR_STAT 0x01
#define INDEX_STAT 0x02
#define ECC_STAT 0x04 /* Corrected error */
#define DRQ_STAT 0x08
#define SEEK_STAT 0x10
#define SERVICE_STAT SEEK_STAT
#define WRERR_STAT 0x20
#define READY_STAT 0x40
#define BUSY_STAT 0x80
/* Bits for HD_ERROR */
#define MARK_ERR 0x01 /* Bad address mark */
#define TRK0_ERR 0x02 /* couldn't find track 0 */
#define ABRT_ERR 0x04 /* Command aborted */
#define MCR_ERR 0x08 /* media change request */
#define ID_ERR 0x10 /* ID field not found */
#define MC_ERR 0x20 /* media changed */
#define ECC_ERR 0x40 /* Uncorrectable ECC error */
#define BBD_ERR 0x80 /* pre-EIDE meaning: block marked bad */
#define ICRC_ERR 0x80 /* new meaning: CRC error during transfer */
/*
* sector count bits
*/
#define NSEC_CD 0x01
#define NSEC_IO 0x02
#define NSEC_REL 0x04
/* /*
* Command Header sizes for IOCTL commands * Command Header sizes for IOCTL commands
*/ */
#define HDIO_DRIVE_CMD_HDR_SIZE (4 * sizeof(u8)) #define HDIO_DRIVE_CMD_HDR_SIZE (4 * sizeof(u8))
#define HDIO_DRIVE_HOB_HDR_SIZE (8 * sizeof(u8)) #define HDIO_DRIVE_HOB_HDR_SIZE (8 * sizeof(u8))
#define IDE_DRIVE_TASK_INVALID -1
#define IDE_DRIVE_TASK_NO_DATA 0
#define IDE_DRIVE_TASK_SET_XFER 1
#define IDE_DRIVE_TASK_IN 2
#define IDE_DRIVE_TASK_OUT 3
#define IDE_DRIVE_TASK_RAW_WRITE 4
struct hd_drive_task_hdr {
u8 feature;
u8 sector_count;
u8 sector_number;
u8 low_cylinder;
u8 high_cylinder;
u8 device_head;
} __attribute__((packed));
/*
* Define standard taskfile in/out register
*/
#define IDE_TASKFILE_STD_OUT_FLAGS 0xFE
#define IDE_TASKFILE_STD_IN_FLAGS 0xFE
#define IDE_HOB_STD_OUT_FLAGS 0xC0
#define IDE_HOB_STD_IN_FLAGS 0xC0
#define TASKFILE_INVALID 0x7fff
#define TASKFILE_48 0x8000
#define TASKFILE_NO_DATA 0x0000
#define TASKFILE_IN 0x0001
#define TASKFILE_MULTI_IN 0x0002
#define TASKFILE_OUT 0x0004
#define TASKFILE_MULTI_OUT 0x0008
#define TASKFILE_IN_OUT 0x0010
#define TASKFILE_IN_DMA 0x0020
#define TASKFILE_OUT_DMA 0x0040
#define TASKFILE_IN_DMAQ 0x0080
#define TASKFILE_OUT_DMAQ 0x0100
#define TASKFILE_P_IN 0x0200
#define TASKFILE_P_OUT 0x0400
#define TASKFILE_P_IN_DMA 0x0800
#define TASKFILE_P_OUT_DMA 0x1000
#define TASKFILE_P_IN_DMAQ 0x2000
#define TASKFILE_P_OUT_DMAQ 0x4000
/* ATA/ATAPI Commands pre T13 Spec */
#define WIN_NOP 0x00
#define CFA_REQ_EXT_ERROR_CODE 0x03 /* CFA Request Extended Error Code */
#define WIN_SRST 0x08 /* ATAPI soft reset command */
#define WIN_DEVICE_RESET 0x08
#define WIN_RESTORE 0x10
#define WIN_READ 0x20 /* 28-Bit */
#define WIN_READ_EXT 0x24 /* 48-Bit */
#define WIN_READDMA_EXT 0x25 /* 48-Bit */
#define WIN_READDMA_QUEUED_EXT 0x26 /* 48-Bit */
#define WIN_READ_NATIVE_MAX_EXT 0x27 /* 48-Bit */
#define WIN_MULTREAD_EXT 0x29 /* 48-Bit */
#define WIN_WRITE 0x30 /* 28-Bit */
#define WIN_WRITE_EXT 0x34 /* 48-Bit */
#define WIN_WRITEDMA_EXT 0x35 /* 48-Bit */
#define WIN_WRITEDMA_QUEUED_EXT 0x36 /* 48-Bit */
#define WIN_SET_MAX_EXT 0x37 /* 48-Bit */
#define CFA_WRITE_SECT_WO_ERASE 0x38 /* CFA Write Sectors without erase */
#define WIN_MULTWRITE_EXT 0x39 /* 48-Bit */
#define WIN_WRITE_VERIFY 0x3C /* 28-Bit */
#define WIN_VERIFY 0x40 /* 28-Bit - Read Verify Sectors */
#define WIN_VERIFY_EXT 0x42 /* 48-Bit */
#define WIN_FORMAT 0x50
#define WIN_INIT 0x60
#define WIN_SEEK 0x70
#define CFA_TRANSLATE_SECTOR 0x87 /* CFA Translate Sector */
#define WIN_DIAGNOSE 0x90
#define WIN_SPECIFY 0x91 /* set drive geometry translation */
#define WIN_DOWNLOAD_MICROCODE 0x92
#define WIN_STANDBYNOW2 0x94
#define WIN_SETIDLE2 0x97
#define WIN_CHECKPOWERMODE2 0x98
#define WIN_SLEEPNOW2 0x99
#define WIN_PACKETCMD 0xA0 /* Send a packet command. */
#define WIN_PIDENTIFY 0xA1 /* identify ATAPI device */
#define WIN_QUEUED_SERVICE 0xA2
#define WIN_SMART 0xB0 /* self-monitoring and reporting */
#define CFA_ERASE_SECTORS 0xC0
#define WIN_MULTREAD 0xC4 /* read sectors using multiple mode*/
#define WIN_MULTWRITE 0xC5 /* write sectors using multiple mode */
#define WIN_SETMULT 0xC6 /* enable/disable multiple mode */
#define WIN_READDMA_QUEUED 0xC7 /* read sectors using Queued DMA transfers */
#define WIN_READDMA 0xC8 /* read sectors using DMA transfers */
#define WIN_WRITEDMA 0xCA /* write sectors using DMA transfers */
#define WIN_WRITEDMA_QUEUED 0xCC /* write sectors using Queued DMA transfers */
#define CFA_WRITE_MULTI_WO_ERASE 0xCD /* CFA Write multiple without erase */
#define WIN_GETMEDIASTATUS 0xDA
#define WIN_DOORLOCK 0xDE /* lock door on removable drives */
#define WIN_DOORUNLOCK 0xDF /* unlock door on removable drives */
#define WIN_STANDBYNOW1 0xE0
#define WIN_IDLEIMMEDIATE 0xE1 /* force drive to become "ready" */
#define WIN_STANDBY 0xE2 /* Set device in Standby Mode */
#define WIN_SETIDLE1 0xE3
#define WIN_READ_BUFFER 0xE4 /* force read only 1 sector */
#define WIN_CHECKPOWERMODE1 0xE5
#define WIN_SLEEPNOW1 0xE6
#define WIN_FLUSH_CACHE 0xE7
#define WIN_WRITE_BUFFER 0xE8 /* force write only 1 sector */
#define WIN_FLUSH_CACHE_EXT 0xEA /* 48-Bit */
#define WIN_IDENTIFY 0xEC /* ask drive to identify itself */
#define WIN_MEDIAEJECT 0xED
#define WIN_IDENTIFY_DMA 0xEE /* same as WIN_IDENTIFY, but DMA */
#define WIN_SETFEATURES 0xEF /* set special drive features */
#define EXABYTE_ENABLE_NEST 0xF0
#define WIN_SECURITY_SET_PASS 0xF1
#define WIN_SECURITY_UNLOCK 0xF2
#define WIN_SECURITY_ERASE_PREPARE 0xF3
#define WIN_SECURITY_ERASE_UNIT 0xF4
#define WIN_SECURITY_FREEZE_LOCK 0xF5
#define WIN_SECURITY_DISABLE 0xF6
#define WIN_READ_NATIVE_MAX 0xF8 /* return the native maximum address */
#define WIN_SET_MAX 0xF9
#define DISABLE_SEAGATE 0xFB
/* WIN_SMART sub-commands */
#define SMART_READ_VALUES 0xD0
#define SMART_READ_THRESHOLDS 0xD1
#define SMART_AUTOSAVE 0xD2
#define SMART_SAVE 0xD3
#define SMART_IMMEDIATE_OFFLINE 0xD4
#define SMART_READ_LOG_SECTOR 0xD5
#define SMART_WRITE_LOG_SECTOR 0xD6
#define SMART_WRITE_THRESHOLDS 0xD7
#define SMART_ENABLE 0xD8
#define SMART_DISABLE 0xD9
#define SMART_STATUS 0xDA
#define SMART_AUTO_OFFLINE 0xDB
/* Password used in TF4 & TF5 executing SMART commands */
#define SMART_LCYL_PASS 0x4F
#define SMART_HCYL_PASS 0xC2
/* WIN_SETFEATURES sub-commands */
#define SETFEATURES_EN_WCACHE 0x02 /* Enable write cache */
#define SETFEATURES_XFER 0x03 /* Set transfer mode */
# define XFER_UDMA_7 0x47 /* 0100|0111 */
# define XFER_UDMA_6 0x46 /* 0100|0110 */
# define XFER_UDMA_5 0x45 /* 0100|0101 */
# define XFER_UDMA_4 0x44 /* 0100|0100 */
# define XFER_UDMA_3 0x43 /* 0100|0011 */
# define XFER_UDMA_2 0x42 /* 0100|0010 */
# define XFER_UDMA_1 0x41 /* 0100|0001 */
# define XFER_UDMA_0 0x40 /* 0100|0000 */
# define XFER_MW_DMA_2 0x22 /* 0010|0010 */
# define XFER_MW_DMA_1 0x21 /* 0010|0001 */
# define XFER_MW_DMA_0 0x20 /* 0010|0000 */
# define XFER_SW_DMA_2 0x12 /* 0001|0010 */
# define XFER_SW_DMA_1 0x11 /* 0001|0001 */
# define XFER_SW_DMA_0 0x10 /* 0001|0000 */
# define XFER_PIO_4 0x0C /* 0000|1100 */
# define XFER_PIO_3 0x0B /* 0000|1011 */
# define XFER_PIO_2 0x0A /* 0000|1010 */
# define XFER_PIO_1 0x09 /* 0000|1001 */
# define XFER_PIO_0 0x08 /* 0000|1000 */
# define XFER_PIO_SLOW 0x00 /* 0000|0000 */
#define SETFEATURES_DIS_DEFECT 0x04 /* Disable Defect Management */
#define SETFEATURES_EN_APM 0x05 /* Enable advanced power management */
#define SETFEATURES_DIS_MSN 0x31 /* Disable Media Status Notification */
#define SETFEATURES_EN_AAM 0x42 /* Enable Automatic Acoustic Management */
#define SETFEATURES_DIS_RLA 0x55 /* Disable read look-ahead feature */
#define SETFEATURES_EN_RI 0x5D /* Enable release interrupt */
#define SETFEATURES_EN_SI 0x5E /* Enable SERVICE interrupt */
#define SETFEATURES_DIS_RPOD 0x66 /* Disable reverting to power on defaults */
#define SETFEATURES_DIS_WCACHE 0x82 /* Disable write cache */
#define SETFEATURES_EN_DEFECT 0x84 /* Enable Defect Management */
#define SETFEATURES_DIS_APM 0x85 /* Disable advanced power management */
#define SETFEATURES_EN_MSN 0x95 /* Enable Media Status Notification */
#define SETFEATURES_EN_RLA 0xAA /* Enable read look-ahead feature */
#define SETFEATURES_PREFETCH 0xAB /* Sets drive prefetch value */
#define SETFEATURES_DIS_AAM 0xC2 /* Disable Automatic Acoustic Management */
#define SETFEATURES_EN_RPOD 0xCC /* Enable reverting to power on defaults */
#define SETFEATURES_DIS_RI 0xDD /* Disable release interrupt */
#define SETFEATURES_DIS_SI 0xDE /* Disable SERVICE interrupt */
/* WIN_SECURITY sub-commands */
#define SECURITY_SET_PASSWORD 0xBA
#define SECURITY_UNLOCK 0xBB
#define SECURITY_ERASE_PREPARE 0xBC
#define SECURITY_ERASE_UNIT 0xBD
#define SECURITY_FREEZE_LOCK 0xBE
#define SECURITY_DISABLE_PASSWORD 0xBF
struct hd_geometry { struct hd_geometry {
u8 heads; __u8 heads;
u8 sectors; __u8 sectors;
u16 cylinders; __u16 cylinders;
unsigned long start;
};
/* BIG GEOMETRY - dying, used only by HDIO_GETGEO_BIG_RAW */
struct hd_big_geometry {
u8 heads;
u8 sectors;
u32 cylinders;
unsigned long start; unsigned long start;
}; };
...@@ -306,263 +45,8 @@ struct hd_big_geometry { ...@@ -306,263 +45,8 @@ struct hd_big_geometry {
#define HDIO_SET_QDMA 0x032e /* change use-qdma flag */ #define HDIO_SET_QDMA 0x032e /* change use-qdma flag */
#define HDIO_SET_ADDRESS 0x032f /* change lba addressing modes */ #define HDIO_SET_ADDRESS 0x032f /* change lba addressing modes */
/* bus states */
enum {
BUSSTATE_OFF = 0,
BUSSTATE_ON,
BUSSTATE_TRISTATE
};
/* hd/ide ctl's that pass (arg) ptrs to user space are numbered 0x033n/0x033n */ /* hd/ide ctl's that pass (arg) ptrs to user space are numbered 0x033n/0x033n */
/* 0x330 is reserved - used to be HDIO_GETGEO_BIG */ /* 0x330 is reserved - used to be HDIO_GETGEO_BIG */
#define HDIO_GETGEO_BIG_RAW 0x0331 /* */ #define HDIO_GETGEO_BIG_RAW 0x0331 /* */
#define __NEW_HD_DRIVE_ID
/*
* Structure returned by HDIO_GET_IDENTITY, as per ANSI NCITS ATA6 rev.1b spec.
*
* If you change something here, please remember to update fix_driveid() in
* ide/probe.c.
*/
struct hd_driveid {
u16 config; /* lots of obsolete bit flags */
u16 cyls; /* Obsolete, "physical" cyls */
u16 reserved2; /* reserved (word 2) */
u16 heads; /* Obsolete, "physical" heads */
u16 track_bytes; /* unformatted bytes per track */
u16 sector_bytes; /* unformatted bytes per sector */
u16 sectors; /* Obsolete, "physical" sectors per track */
u16 vendor0; /* vendor unique */
u16 vendor1; /* vendor unique */
u16 vendor2; /* Retired vendor unique */
u8 serial_no[20]; /* 0 = not_specified */
u16 buf_type; /* Retired */
u16 buf_size; /* Retired, 512 byte increments
* 0 = not_specified
*/
u16 ecc_bytes; /* for r/w long cmds; 0 = not_specified */
u8 fw_rev[8]; /* 0 = not_specified */
char model[40]; /* 0 = not_specified */
u8 max_multsect; /* 0=not_implemented */
u8 vendor3; /* vendor unique */
u16 dword_io; /* 0=not_implemented; 1=implemented */
u8 vendor4; /* vendor unique */
u8 capability; /* (upper byte of word 49)
* 3: IORDYsup
* 2: IORDYsw
* 1: LBA
* 0: DMA
*/
u16 reserved50; /* reserved (word 50) */
u8 vendor5; /* Obsolete, vendor unique */
u8 tPIO; /* Obsolete, 0=slow, 1=medium, 2=fast */
u8 vendor6; /* Obsolete, vendor unique */
u8 tDMA; /* Obsolete, 0=slow, 1=medium, 2=fast */
u16 field_valid; /* (word 53)
* 2: ultra_ok word 88
* 1: eide_ok words 64-70
* 0: cur_ok words 54-58
*/
u16 cur_cyls; /* Obsolete, logical cylinders */
u16 cur_heads; /* Obsolete, l heads */
u16 cur_sectors; /* Obsolete, l sectors per track */
u16 cur_capacity0; /* Obsolete, l total sectors on drive */
u16 cur_capacity1; /* Obsolete, (2 words, misaligned int) */
u8 multsect; /* current multiple sector count */
u8 multsect_valid; /* when (bit0==1) multsect is ok */
u32 lba_capacity; /* Obsolete, total number of sectors */
u16 dma_1word; /* Obsolete, single-word dma info */
u16 dma_mword; /* multiple-word dma info */
u16 eide_pio_modes; /* bits 0:mode3 1:mode4 */
u16 eide_dma_min; /* min mword dma cycle time (ns) */
u16 eide_dma_time; /* recommended mword dma cycle time (ns) */
u16 eide_pio; /* min cycle time (ns), no IORDY */
u16 eide_pio_iordy; /* min cycle time (ns), with IORDY */
u16 words69_70[2]; /* reserved words 69-70
* future command overlap and queuing
*/
/* HDIO_GET_IDENTITY currently returns only words 0 through 70 */
u16 words71_74[4]; /* reserved words 71-74
* for IDENTIFY PACKET DEVICE command
*/
u16 queue_depth; /* (word 75)
* 15:5 reserved
* 4:0 Maximum queue depth -1
*/
u16 words76_79[4]; /* reserved words 76-79 */
u16 major_rev_num; /* (word 80) */
u16 minor_rev_num; /* (word 81) */
u16 command_set_1; /* (word 82) supported
* 15: Obsolete
* 14: NOP command
* 13: READ_BUFFER
* 12: WRITE_BUFFER
* 11: Obsolete
* 10: Host Protected Area
* 9: DEVICE Reset
* 8: SERVICE Interrupt
* 7: Release Interrupt
* 6: look-ahead
* 5: write cache
* 4: PACKET Command
* 3: Power Management Feature Set
* 2: Removable Feature Set
* 1: Security Feature Set
* 0: SMART Feature Set
*/
u16 command_set_2; /* (word 83)
* 15: Shall be ZERO
* 14: Shall be ONE
* 13: FLUSH CACHE EXT
* 12: FLUSH CACHE
* 11: Device Configuration Overlay
* 10: 48-bit Address Feature Set
* 9: Automatic Acoustic Management
* 8: SET MAX security
* 7: reserved 1407DT PARTIES
* 6: SetF sub-command Power-Up
* 5: Power-Up in Standby Feature Set
* 4: Removable Media Notification
* 3: APM Feature Set
* 2: CFA Feature Set
* 1: READ/WRITE DMA QUEUED
* 0: Download MicroCode
*/
u16 cfsse; /* (word 84)
* cmd set-feature supported extensions
* 15: Shall be ZERO
* 14: Shall be ONE
* 13:3 reserved
* 2: Media Serial Number Valid
* 1: SMART selt-test supported
* 0: SMART error logging
*/
u16 cfs_enable_1; /* (word 85)
* command set-feature enabled
* 15: Obsolete
* 14: NOP command
* 13: READ_BUFFER
* 12: WRITE_BUFFER
* 11: Obsolete
* 10: Host Protected Area
* 9: DEVICE Reset
* 8: SERVICE Interrupt
* 7: Release Interrupt
* 6: look-ahead
* 5: write cache
* 4: PACKET Command
* 3: Power Management Feature Set
* 2: Removable Feature Set
* 1: Security Feature Set
* 0: SMART Feature Set
*/
u16 cfs_enable_2; /* (word 86)
* command set-feature enabled
* 15: Shall be ZERO
* 14: Shall be ONE
* 13: FLUSH CACHE EXT
* 12: FLUSH CACHE
* 11: Device Configuration Overlay
* 10: 48-bit Address Feature Set
* 9: Automatic Acoustic Management
* 8: SET MAX security
* 7: reserved 1407DT PARTIES
* 6: SetF sub-command Power-Up
* 5: Power-Up in Standby Feature Set
* 4: Removable Media Notification
* 3: APM Feature Set
* 2: CFA Feature Set
* 1: READ/WRITE DMA QUEUED
* 0: Download MicroCode
*/
u16 csf_default; /* (word 87)
* command set-feature default
* 15: Shall be ZERO
* 14: Shall be ONE
* 13:3 reserved
* 2: Media Serial Number Valid
* 1: SMART selt-test supported
* 0: SMART error logging
*/
u16 dma_ultra; /* (word 88) */
u16 word89; /* reserved (word 89) */
u16 word90; /* reserved (word 90) */
u16 CurAPMvalues; /* current APM values */
u16 word92; /* reserved (word 92) */
u16 hw_config; /* hardware config (word 93)
* 15:
* 14:
* 13:
* 12:
* 11:
* 10:
* 9:
* 8:
* 7:
* 6:
* 5:
* 4:
* 3:
* 2:
* 1:
* 0:
*/
u16 acoustic; /* (word 94)
* 15:8 Vendor's recommended value
* 7:0 current value
*/
u16 words95_99[5]; /* reserved words 95-99 */
u64 lba_capacity_2; /* 48-bit total number of sectors */
u16 words104_125[22];/* reserved words 104-125 */
u16 last_lun; /* (word 126) */
u16 word127; /* (word 127) Feature Set
* Removable Media Notification
* 15:2 reserved
* 1:0 00 = not supported
* 01 = supported
* 10 = reserved
* 11 = reserved
*/
u16 dlf; /* (word 128)
* device lock function
* 15:9 reserved
* 8 security level 1:max 0:high
* 7:6 reserved
* 5 enhanced erase
* 4 expire
* 3 frozen
* 2 locked
* 1 en/disabled
* 0 capability
*/
u16 csfo; /* (word 129)
* current set features options
* 15:4 reserved
* 3: auto reassign
* 2: reverting
* 1: read-look-ahead
* 0: write cache
*/
u16 words130_155[26];/* reserved vendor words 130-155 */
u16 word156; /* reserved vendor word 156 */
u16 words157_159[3];/* reserved vendor words 157-159 */
u16 cfa_power; /* (word 160) CFA Power Mode
* 15 word 160 supported
* 14 reserved
* 13
* 12
* 11:0
*/
u16 words161_175[14];/* Reserved for CFA */
u16 words176_205[31];/* Current Media Serial Number */
u16 words206_254[48];/* reserved words 206-254 */
u16 integrity_word; /* (word 255)
* 15:8 Checksum
* 7:0 Signature
*/
} __attribute__((packed));
#define IDE_NICE_DSC_OVERLAP (0) /* per the DSC overlap protocol */
#endif #endif
...@@ -8,7 +8,6 @@ ...@@ -8,7 +8,6 @@
#include <linux/config.h> #include <linux/config.h>
#include <linux/init.h> #include <linux/init.h>
#include <linux/ioport.h> #include <linux/ioport.h>
#include <linux/hdreg.h>
#include <linux/hdsmart.h> #include <linux/hdsmart.h>
#include <linux/blkdev.h> #include <linux/blkdev.h>
#include <linux/proc_fs.h> #include <linux/proc_fs.h>
...@@ -51,7 +50,460 @@ ...@@ -51,7 +50,460 @@
* "No user-serviceable parts" beyond this point * "No user-serviceable parts" beyond this point
*****************************************************************************/ *****************************************************************************/
typedef unsigned char byte; /* used everywhere */
/* ATA/ATAPI Commands pre T13 Spec */
#define WIN_NOP 0x00
#define CFA_REQ_EXT_ERROR_CODE 0x03 /* CFA Request Extended Error Code */
#define WIN_SRST 0x08 /* ATAPI soft reset command */
#define WIN_DEVICE_RESET 0x08
#define WIN_RESTORE 0x10
#define WIN_READ 0x20 /* 28-Bit */
#define WIN_READ_EXT 0x24 /* 48-Bit */
#define WIN_READDMA_EXT 0x25 /* 48-Bit */
#define WIN_READDMA_QUEUED_EXT 0x26 /* 48-Bit */
#define WIN_READ_NATIVE_MAX_EXT 0x27 /* 48-Bit */
#define WIN_MULTREAD_EXT 0x29 /* 48-Bit */
#define WIN_WRITE 0x30 /* 28-Bit */
#define WIN_WRITE_EXT 0x34 /* 48-Bit */
#define WIN_WRITEDMA_EXT 0x35 /* 48-Bit */
#define WIN_WRITEDMA_QUEUED_EXT 0x36 /* 48-Bit */
#define WIN_SET_MAX_EXT 0x37 /* 48-Bit */
#define CFA_WRITE_SECT_WO_ERASE 0x38 /* CFA Write Sectors without erase */
#define WIN_MULTWRITE_EXT 0x39 /* 48-Bit */
#define WIN_WRITE_VERIFY 0x3C /* 28-Bit */
#define WIN_VERIFY 0x40 /* 28-Bit - Read Verify Sectors */
#define WIN_VERIFY_EXT 0x42 /* 48-Bit */
#define WIN_FORMAT 0x50
#define WIN_INIT 0x60
#define WIN_SEEK 0x70
#define CFA_TRANSLATE_SECTOR 0x87 /* CFA Translate Sector */
#define WIN_DIAGNOSE 0x90
#define WIN_SPECIFY 0x91 /* set drive geometry translation */
#define WIN_DOWNLOAD_MICROCODE 0x92
#define WIN_STANDBYNOW2 0x94
#define WIN_SETIDLE2 0x97
#define WIN_CHECKPOWERMODE2 0x98
#define WIN_SLEEPNOW2 0x99
#define WIN_PACKETCMD 0xA0 /* Send a packet command. */
#define WIN_PIDENTIFY 0xA1 /* identify ATAPI device */
#define WIN_QUEUED_SERVICE 0xA2
#define WIN_SMART 0xB0 /* self-monitoring and reporting */
#define CFA_ERASE_SECTORS 0xC0
#define WIN_MULTREAD 0xC4 /* read sectors using multiple mode*/
#define WIN_MULTWRITE 0xC5 /* write sectors using multiple mode */
#define WIN_SETMULT 0xC6 /* enable/disable multiple mode */
#define WIN_READDMA_QUEUED 0xC7 /* read sectors using Queued DMA transfers */
#define WIN_READDMA 0xC8 /* read sectors using DMA transfers */
#define WIN_WRITEDMA 0xCA /* write sectors using DMA transfers */
#define WIN_WRITEDMA_QUEUED 0xCC /* write sectors using Queued DMA transfers */
#define CFA_WRITE_MULTI_WO_ERASE 0xCD /* CFA Write multiple without erase */
#define WIN_GETMEDIASTATUS 0xDA
#define WIN_DOORLOCK 0xDE /* lock door on removable drives */
#define WIN_DOORUNLOCK 0xDF /* unlock door on removable drives */
#define WIN_STANDBYNOW1 0xE0
#define WIN_IDLEIMMEDIATE 0xE1 /* force drive to become "ready" */
#define WIN_STANDBY 0xE2 /* Set device in Standby Mode */
#define WIN_SETIDLE1 0xE3
#define WIN_READ_BUFFER 0xE4 /* force read only 1 sector */
#define WIN_CHECKPOWERMODE1 0xE5
#define WIN_SLEEPNOW1 0xE6
#define WIN_FLUSH_CACHE 0xE7
#define WIN_WRITE_BUFFER 0xE8 /* force write only 1 sector */
#define WIN_FLUSH_CACHE_EXT 0xEA /* 48-Bit */
#define WIN_IDENTIFY 0xEC /* ask drive to identify itself */
#define WIN_MEDIAEJECT 0xED
#define WIN_IDENTIFY_DMA 0xEE /* same as WIN_IDENTIFY, but DMA */
#define WIN_SETFEATURES 0xEF /* set special drive features */
#define EXABYTE_ENABLE_NEST 0xF0
#define WIN_SECURITY_SET_PASS 0xF1
#define WIN_SECURITY_UNLOCK 0xF2
#define WIN_SECURITY_ERASE_PREPARE 0xF3
#define WIN_SECURITY_ERASE_UNIT 0xF4
#define WIN_SECURITY_FREEZE_LOCK 0xF5
#define WIN_SECURITY_DISABLE 0xF6
#define WIN_READ_NATIVE_MAX 0xF8 /* return the native maximum address */
#define WIN_SET_MAX 0xF9
#define DISABLE_SEAGATE 0xFB
/* WIN_SMART sub-commands */
#define SMART_READ_VALUES 0xD0
#define SMART_READ_THRESHOLDS 0xD1
#define SMART_AUTOSAVE 0xD2
#define SMART_SAVE 0xD3
#define SMART_IMMEDIATE_OFFLINE 0xD4
#define SMART_READ_LOG_SECTOR 0xD5
#define SMART_WRITE_LOG_SECTOR 0xD6
#define SMART_WRITE_THRESHOLDS 0xD7
#define SMART_ENABLE 0xD8
#define SMART_DISABLE 0xD9
#define SMART_STATUS 0xDA
#define SMART_AUTO_OFFLINE 0xDB
/* Password used in TF4 & TF5 executing SMART commands */
#define SMART_LCYL_PASS 0x4F
#define SMART_HCYL_PASS 0xC2
/* WIN_SETFEATURES sub-commands */
#define SETFEATURES_EN_WCACHE 0x02 /* Enable write cache */
#define SETFEATURES_XFER 0x03 /* Set transfer mode */
# define XFER_UDMA_7 0x47 /* 0100|0111 */
# define XFER_UDMA_6 0x46 /* 0100|0110 */
# define XFER_UDMA_5 0x45 /* 0100|0101 */
# define XFER_UDMA_4 0x44 /* 0100|0100 */
# define XFER_UDMA_3 0x43 /* 0100|0011 */
# define XFER_UDMA_2 0x42 /* 0100|0010 */
# define XFER_UDMA_1 0x41 /* 0100|0001 */
# define XFER_UDMA_0 0x40 /* 0100|0000 */
# define XFER_MW_DMA_2 0x22 /* 0010|0010 */
# define XFER_MW_DMA_1 0x21 /* 0010|0001 */
# define XFER_MW_DMA_0 0x20 /* 0010|0000 */
# define XFER_SW_DMA_2 0x12 /* 0001|0010 */
# define XFER_SW_DMA_1 0x11 /* 0001|0001 */
# define XFER_SW_DMA_0 0x10 /* 0001|0000 */
# define XFER_PIO_4 0x0C /* 0000|1100 */
# define XFER_PIO_3 0x0B /* 0000|1011 */
# define XFER_PIO_2 0x0A /* 0000|1010 */
# define XFER_PIO_1 0x09 /* 0000|1001 */
# define XFER_PIO_0 0x08 /* 0000|1000 */
# define XFER_PIO_SLOW 0x00 /* 0000|0000 */
#define SETFEATURES_DIS_DEFECT 0x04 /* Disable Defect Management */
#define SETFEATURES_EN_APM 0x05 /* Enable advanced power management */
#define SETFEATURES_DIS_MSN 0x31 /* Disable Media Status Notification */
#define SETFEATURES_EN_AAM 0x42 /* Enable Automatic Acoustic Management */
#define SETFEATURES_DIS_RLA 0x55 /* Disable read look-ahead feature */
#define SETFEATURES_EN_RI 0x5D /* Enable release interrupt */
#define SETFEATURES_EN_SI 0x5E /* Enable SERVICE interrupt */
#define SETFEATURES_DIS_RPOD 0x66 /* Disable reverting to power on defaults */
#define SETFEATURES_DIS_WCACHE 0x82 /* Disable write cache */
#define SETFEATURES_EN_DEFECT 0x84 /* Enable Defect Management */
#define SETFEATURES_DIS_APM 0x85 /* Disable advanced power management */
#define SETFEATURES_EN_MSN 0x95 /* Enable Media Status Notification */
#define SETFEATURES_EN_RLA 0xAA /* Enable read look-ahead feature */
#define SETFEATURES_PREFETCH 0xAB /* Sets drive prefetch value */
#define SETFEATURES_DIS_AAM 0xC2 /* Disable Automatic Acoustic Management */
#define SETFEATURES_EN_RPOD 0xCC /* Enable reverting to power on defaults */
#define SETFEATURES_DIS_RI 0xDD /* Disable release interrupt */
#define SETFEATURES_DIS_SI 0xDE /* Disable SERVICE interrupt */
/* WIN_SECURITY sub-commands */
#define SECURITY_SET_PASSWORD 0xBA
#define SECURITY_UNLOCK 0xBB
#define SECURITY_ERASE_PREPARE 0xBC
#define SECURITY_ERASE_UNIT 0xBD
#define SECURITY_FREEZE_LOCK 0xBE
#define SECURITY_DISABLE_PASSWORD 0xBF
/* Taskfile related constants.
*/
#define IDE_DRIVE_TASK_INVALID -1
#define IDE_DRIVE_TASK_NO_DATA 0
#define IDE_DRIVE_TASK_SET_XFER 1
#define IDE_DRIVE_TASK_IN 2
#define IDE_DRIVE_TASK_OUT 3
#define IDE_DRIVE_TASK_RAW_WRITE 4
struct hd_drive_task_hdr {
u8 feature;
u8 sector_count;
u8 sector_number;
u8 low_cylinder;
u8 high_cylinder;
u8 device_head;
} __attribute__((packed));
/*
* Define standard taskfile in/out register
*/
#define IDE_TASKFILE_STD_OUT_FLAGS 0xFE
#define IDE_TASKFILE_STD_IN_FLAGS 0xFE
#define IDE_HOB_STD_OUT_FLAGS 0xC0
#define IDE_HOB_STD_IN_FLAGS 0xC0
#define TASKFILE_INVALID 0x7fff
#define TASKFILE_48 0x8000
#define TASKFILE_NO_DATA 0x0000
#define TASKFILE_IN 0x0001
#define TASKFILE_MULTI_IN 0x0002
#define TASKFILE_OUT 0x0004
#define TASKFILE_MULTI_OUT 0x0008
#define TASKFILE_IN_OUT 0x0010
#define TASKFILE_IN_DMA 0x0020
#define TASKFILE_OUT_DMA 0x0040
#define TASKFILE_IN_DMAQ 0x0080
#define TASKFILE_OUT_DMAQ 0x0100
#define TASKFILE_P_IN 0x0200
#define TASKFILE_P_OUT 0x0400
#define TASKFILE_P_IN_DMA 0x0800
#define TASKFILE_P_OUT_DMA 0x1000
#define TASKFILE_P_IN_DMAQ 0x2000
#define TASKFILE_P_OUT_DMAQ 0x4000
/* bus states */
enum {
BUSSTATE_OFF = 0,
BUSSTATE_ON,
BUSSTATE_TRISTATE
};
/*
* Structure returned by HDIO_GET_IDENTITY, as per ANSI NCITS ATA6 rev.1b spec.
*
* If you change something here, please remember to update fix_driveid() in
* ide/probe.c.
*/
struct hd_driveid {
u16 config; /* lots of obsolete bit flags */
u16 cyls; /* Obsolete, "physical" cyls */
u16 reserved2; /* reserved (word 2) */
u16 heads; /* Obsolete, "physical" heads */
u16 track_bytes; /* unformatted bytes per track */
u16 sector_bytes; /* unformatted bytes per sector */
u16 sectors; /* Obsolete, "physical" sectors per track */
u16 vendor0; /* vendor unique */
u16 vendor1; /* vendor unique */
u16 vendor2; /* Retired vendor unique */
u8 serial_no[20]; /* 0 = not_specified */
u16 buf_type; /* Retired */
u16 buf_size; /* Retired, 512 byte increments
* 0 = not_specified
*/
u16 ecc_bytes; /* for r/w long cmds; 0 = not_specified */
u8 fw_rev[8]; /* 0 = not_specified */
char model[40]; /* 0 = not_specified */
u8 max_multsect; /* 0=not_implemented */
u8 vendor3; /* vendor unique */
u16 dword_io; /* 0=not_implemented; 1=implemented */
u8 vendor4; /* vendor unique */
u8 capability; /* (upper byte of word 49)
* 3: IORDYsup
* 2: IORDYsw
* 1: LBA
* 0: DMA
*/
u16 reserved50; /* reserved (word 50) */
u8 vendor5; /* Obsolete, vendor unique */
u8 tPIO; /* Obsolete, 0=slow, 1=medium, 2=fast */
u8 vendor6; /* Obsolete, vendor unique */
u8 tDMA; /* Obsolete, 0=slow, 1=medium, 2=fast */
u16 field_valid; /* (word 53)
* 2: ultra_ok word 88
* 1: eide_ok words 64-70
* 0: cur_ok words 54-58
*/
u16 cur_cyls; /* Obsolete, logical cylinders */
u16 cur_heads; /* Obsolete, l heads */
u16 cur_sectors; /* Obsolete, l sectors per track */
u16 cur_capacity0; /* Obsolete, l total sectors on drive */
u16 cur_capacity1; /* Obsolete, (2 words, misaligned int) */
u8 multsect; /* current multiple sector count */
u8 multsect_valid; /* when (bit0==1) multsect is ok */
u32 lba_capacity; /* Obsolete, total number of sectors */
u16 dma_1word; /* Obsolete, single-word dma info */
u16 dma_mword; /* multiple-word dma info */
u16 eide_pio_modes; /* bits 0:mode3 1:mode4 */
u16 eide_dma_min; /* min mword dma cycle time (ns) */
u16 eide_dma_time; /* recommended mword dma cycle time (ns) */
u16 eide_pio; /* min cycle time (ns), no IORDY */
u16 eide_pio_iordy; /* min cycle time (ns), with IORDY */
u16 words69_70[2]; /* reserved words 69-70
* future command overlap and queuing
*/
/* HDIO_GET_IDENTITY currently returns only words 0 through 70 */
u16 words71_74[4]; /* reserved words 71-74
* for IDENTIFY PACKET DEVICE command
*/
u16 queue_depth; /* (word 75)
* 15:5 reserved
* 4:0 Maximum queue depth -1
*/
u16 words76_79[4]; /* reserved words 76-79 */
u16 major_rev_num; /* (word 80) */
u16 minor_rev_num; /* (word 81) */
u16 command_set_1; /* (word 82) supported
* 15: Obsolete
* 14: NOP command
* 13: READ_BUFFER
* 12: WRITE_BUFFER
* 11: Obsolete
* 10: Host Protected Area
* 9: DEVICE Reset
* 8: SERVICE Interrupt
* 7: Release Interrupt
* 6: look-ahead
* 5: write cache
* 4: PACKET Command
* 3: Power Management Feature Set
* 2: Removable Feature Set
* 1: Security Feature Set
* 0: SMART Feature Set
*/
u16 command_set_2; /* (word 83)
* 15: Shall be ZERO
* 14: Shall be ONE
* 13: FLUSH CACHE EXT
* 12: FLUSH CACHE
* 11: Device Configuration Overlay
* 10: 48-bit Address Feature Set
* 9: Automatic Acoustic Management
* 8: SET MAX security
* 7: reserved 1407DT PARTIES
* 6: SetF sub-command Power-Up
* 5: Power-Up in Standby Feature Set
* 4: Removable Media Notification
* 3: APM Feature Set
* 2: CFA Feature Set
* 1: READ/WRITE DMA QUEUED
* 0: Download MicroCode
*/
u16 cfsse; /* (word 84)
* cmd set-feature supported extensions
* 15: Shall be ZERO
* 14: Shall be ONE
* 13:3 reserved
* 2: Media Serial Number Valid
* 1: SMART selt-test supported
* 0: SMART error logging
*/
u16 cfs_enable_1; /* (word 85)
* command set-feature enabled
* 15: Obsolete
* 14: NOP command
* 13: READ_BUFFER
* 12: WRITE_BUFFER
* 11: Obsolete
* 10: Host Protected Area
* 9: DEVICE Reset
* 8: SERVICE Interrupt
* 7: Release Interrupt
* 6: look-ahead
* 5: write cache
* 4: PACKET Command
* 3: Power Management Feature Set
* 2: Removable Feature Set
* 1: Security Feature Set
* 0: SMART Feature Set
*/
u16 cfs_enable_2; /* (word 86)
* command set-feature enabled
* 15: Shall be ZERO
* 14: Shall be ONE
* 13: FLUSH CACHE EXT
* 12: FLUSH CACHE
* 11: Device Configuration Overlay
* 10: 48-bit Address Feature Set
* 9: Automatic Acoustic Management
* 8: SET MAX security
* 7: reserved 1407DT PARTIES
* 6: SetF sub-command Power-Up
* 5: Power-Up in Standby Feature Set
* 4: Removable Media Notification
* 3: APM Feature Set
* 2: CFA Feature Set
* 1: READ/WRITE DMA QUEUED
* 0: Download MicroCode
*/
u16 csf_default; /* (word 87)
* command set-feature default
* 15: Shall be ZERO
* 14: Shall be ONE
* 13:3 reserved
* 2: Media Serial Number Valid
* 1: SMART selt-test supported
* 0: SMART error logging
*/
u16 dma_ultra; /* (word 88) */
u16 word89; /* reserved (word 89) */
u16 word90; /* reserved (word 90) */
u16 CurAPMvalues; /* current APM values */
u16 word92; /* reserved (word 92) */
u16 hw_config; /* hardware config (word 93)
* 15:
* 14:
* 13:
* 12:
* 11:
* 10:
* 9:
* 8:
* 7:
* 6:
* 5:
* 4:
* 3:
* 2:
* 1:
* 0:
*/
u16 acoustic; /* (word 94)
* 15:8 Vendor's recommended value
* 7:0 current value
*/
u16 words95_99[5]; /* reserved words 95-99 */
u64 lba_capacity_2; /* 48-bit total number of sectors */
u16 words104_125[22];/* reserved words 104-125 */
u16 last_lun; /* (word 126) */
u16 word127; /* (word 127) Feature Set
* Removable Media Notification
* 15:2 reserved
* 1:0 00 = not supported
* 01 = supported
* 10 = reserved
* 11 = reserved
*/
u16 dlf; /* (word 128)
* device lock function
* 15:9 reserved
* 8 security level 1:max 0:high
* 7:6 reserved
* 5 enhanced erase
* 4 expire
* 3 frozen
* 2 locked
* 1 en/disabled
* 0 capability
*/
u16 csfo; /* (word 129)
* current set features options
* 15:4 reserved
* 3: auto reassign
* 2: reverting
* 1: read-look-ahead
* 0: write cache
*/
u16 words130_155[26];/* reserved vendor words 130-155 */
u16 word156; /* reserved vendor word 156 */
u16 words157_159[3];/* reserved vendor words 157-159 */
u16 cfa_power; /* (word 160) CFA Power Mode
* 15 word 160 supported
* 14 reserved
* 13
* 12
* 11:0
*/
u16 words161_175[14];/* Reserved for CFA */
u16 words176_205[31];/* Current Media Serial Number */
u16 words206_254[48];/* reserved words 206-254 */
u16 integrity_word; /* (word 255)
* 15:8 Checksum
* 7:0 Signature
*/
} __attribute__((packed));
#define IDE_NICE_DSC_OVERLAP (0) /* per the DSC overlap protocol */
/* /*
* Probably not wise to fiddle with these * Probably not wise to fiddle with these
...@@ -105,6 +557,35 @@ enum { ...@@ -105,6 +557,35 @@ enum {
#define GET_ALTSTAT() IN_BYTE(drive->channel->io_ports[IDE_CONTROL_OFFSET]) #define GET_ALTSTAT() IN_BYTE(drive->channel->io_ports[IDE_CONTROL_OFFSET])
#define GET_FEAT() IN_BYTE(IDE_NSECTOR_REG) #define GET_FEAT() IN_BYTE(IDE_NSECTOR_REG)
/* Bits of HD_STATUS */
#define ERR_STAT 0x01
#define INDEX_STAT 0x02
#define ECC_STAT 0x04 /* Corrected error */
#define DRQ_STAT 0x08
#define SEEK_STAT 0x10
#define SERVICE_STAT SEEK_STAT
#define WRERR_STAT 0x20
#define READY_STAT 0x40
#define BUSY_STAT 0x80
/* Bits for HD_ERROR */
#define MARK_ERR 0x01 /* Bad address mark */
#define TRK0_ERR 0x02 /* couldn't find track 0 */
#define ABRT_ERR 0x04 /* Command aborted */
#define MCR_ERR 0x08 /* media change request */
#define ID_ERR 0x10 /* ID field not found */
#define MC_ERR 0x20 /* media changed */
#define ECC_ERR 0x40 /* Uncorrectable ECC error */
#define BBD_ERR 0x80 /* pre-EIDE meaning: block marked bad */
#define ICRC_ERR 0x80 /* new meaning: CRC error during transfer */
/*
* sector count bits
*/
#define NSEC_CD 0x01
#define NSEC_IO 0x02
#define NSEC_REL 0x04
#define BAD_R_STAT (BUSY_STAT | ERR_STAT) #define BAD_R_STAT (BUSY_STAT | ERR_STAT)
#define BAD_W_STAT (BAD_R_STAT | WRERR_STAT) #define BAD_W_STAT (BAD_R_STAT | WRERR_STAT)
#define BAD_STAT (BAD_R_STAT | DRQ_STAT) #define BAD_STAT (BAD_R_STAT | DRQ_STAT)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment