Commit 4166c817 authored by David Brownell's avatar David Brownell Committed by Greg Kroah-Hartman

[PATCH] USB: gadget cleanup of #ifdefs

> can you get rid of all of the #ifdef HAVE_DRIVER_MODEL stuff?

Done.  Now this code "knows" it's running in a 2.5
environment, and needs modifications to run on 2.4.

I also changed the file modes in the module_parm()
calls so the parameters will be writable when they
eventually show up in sysfs; and fixed a typo.

Compile-tested with and without DEBUG enabled.
parent 02d57f34
......@@ -118,7 +118,7 @@ config USB_ETH
This driver implements the "Communication Device Class" (CDC)
Ethernet Control Model. That protocol is often avoided with pure
Ethernet adapters, in favor of simpler vendor-specific hardware,
but is widely suppored by firmware for smart network devices.
but is widely supported by firmware for smart network devices.
Within the USB device, this gadget driver exposes a network device
"usbX", where X depends on what other networking devices you have.
......
......@@ -37,6 +37,8 @@
#include <linux/interrupt.h>
#include <linux/uts.h>
#include <linux/version.h>
#include <linux/device.h>
#include <linux/moduleparam.h>
#include <asm/byteorder.h>
#include <asm/io.h>
......@@ -118,17 +120,8 @@ static unsigned qmult = 4;
#define TX_DELAY 8
#ifdef HAVE_DRIVER_MODEL
#include <linux/moduleparam.h>
module_param (qmult, uint, 0);
#else
MODULE_PARM (qmult, "i");
MODULE_PARM_DESC (qmult, "rx/tx buffering factor");
module_param (qmult, uint, S_IRUGO|S_IWUSR);
#endif /* HAVE_DRIVER_MODEL */
/*-------------------------------------------------------------------------*/
......@@ -279,14 +272,8 @@ static const char EP_IN_NAME [] = "ep2in-bulk";
/*-------------------------------------------------------------------------*/
#ifdef HAVE_DRIVER_MODEL
#define xprintk(dev,level,fmt,args...) \
dev_printk(level , &dev->gadget->dev , fmt , ## args)
#else
#define xprintk(dev,level,fmt,args...) \
printk(level "%s %s: " fmt , shortname, dev->gadget->dev.bus_id, \
## args)
#endif /* HAVE_DRIVER_MODEL */
#define xprintk(d,level,fmt,args...) \
dev_printk(level , &(d)->gadget->dev , fmt , ## args)
#ifdef DEBUG
#undef DEBUG
......@@ -954,12 +941,10 @@ static void issue_start_status (struct eth_dev *dev)
static void eth_setup_complete (struct usb_ep *ep, struct usb_request *req)
{
if (req->status || req->actual != req->length) {
struct eth_dev *dev = ep->driver_data;
DEBUG (dev, "setup complete --> %d, %d/%d\n",
if (req->status || req->actual != req->length)
DEBUG ((struct eth_dev *) ep->driver_data,
"setup complete --> %d, %d/%d\n",
req->status, req->actual, req->length);
}
}
/* see section 3.8.2 table 10 of the CDC spec for more ethernet
......
......@@ -60,8 +60,8 @@
#include <linux/timer.h>
#include <linux/list.h>
#include <linux/interrupt.h>
#include <linux/version.h>
#include <linux/moduleparam.h>
#include <linux/device.h>
#include <linux/usb_ch9.h>
#include <linux/usb_gadget.h>
......@@ -79,6 +79,7 @@
#define EP_DONTUSE 13 /* nonzero */
#define USE_RDK_LEDS /* GPIO pins control three LEDs */
#define USE_SYSFS_DEBUG_FILES
static const char driver_name [] = "net2280";
......@@ -93,26 +94,12 @@ static const char *ep_name [] = {
static int use_dma = 1;
#ifdef HAVE_DRIVER_MODEL
#include <linux/moduleparam.h>
/* "modprobe net2280 use_dma=n" etc */
module_param (use_dma, bool, S_IRUGO|S_IWUSR);
#else
/* use zero/nonzero for older versions */
MODULE_PARM (use_dma, "i");
MODULE_PARM_DESC (use_dma, "true to use dma controllers");
#endif
#include "net2280.h"
#define valid_bit cpu_to_le32 (1 << VALID_BIT)
#define dma_done_ie cpu_to_le32 (1 << DMA_DONE_INTERRUPT_ENABLE)
/*-------------------------------------------------------------------------*/
#define DIR_STRING(bAddress) (((bAddress) & USB_DIR_IN) ? "in" : "out")
#if defined(USE_SYSFS_DEBUG_FILES) || defined (DEBUG)
static char *type_string (u8 bmAttributes)
{
switch ((bmAttributes) & USB_ENDPOINT_XFERTYPE_MASK) {
......@@ -122,6 +109,14 @@ static char *type_string (u8 bmAttributes)
};
return "control";
}
#endif
#include "net2280.h"
#define valid_bit cpu_to_le32 (1 << VALID_BIT)
#define dma_done_ie cpu_to_le32 (1 << DMA_DONE_INTERRUPT_ENABLE)
/*-------------------------------------------------------------------------*/
static int
net2280_enable (struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
......@@ -1280,7 +1275,7 @@ static const struct usb_gadget_ops net2280_ops = {
/*-------------------------------------------------------------------------*/
#ifdef HAVE_DRIVER_MODEL
#ifdef USE_SYSFS_DEBUG_FILES
/* "function" sysfs attribute */
static ssize_t
......@@ -1771,25 +1766,19 @@ int usb_gadget_register_driver (struct usb_gadget_driver *driver)
/* hook up the driver ... */
dev->driver = driver;
#ifdef HAVE_DRIVER_MODEL
dev->gadget.dev.driver = &driver->driver;
#endif
retval = driver->bind (&dev->gadget);
if (retval) {
DEBUG (dev, "bind to driver %s --> %d\n",
driver->driver.name, retval);
dev->driver = 0;
#ifdef HAVE_DRIVER_MODEL
dev->gadget.dev.driver = 0;
#endif
return retval;
}
#ifdef HAVE_DRIVER_MODEL
// FIXME
// driver_register (&driver->driver);
// device_register (&dev->gadget.dev);
#endif
device_create_file (&dev->pdev->dev, &dev_attr_function);
device_create_file (&dev->pdev->dev, &dev_attr_queues);
......@@ -2501,14 +2490,10 @@ static int net2280_probe (struct pci_dev *pdev, const struct pci_device_id *id)
dev->pdev = pdev;
dev->gadget.ops = &net2280_ops;
#ifdef HAVE_DRIVER_MODEL
strcpy (dev->gadget.dev.bus_id, pdev->slot_name);
strcpy (dev->gadget.dev.name, pdev->dev.name);
dev->gadget.dev.parent = &pdev->dev;
dev->gadget.dev.dma_mask = pdev->dev.dma_mask;
#else
dev->gadget.dev.bus_id = pdev->slot_name;
#endif
dev->gadget.name = driver_name;
/* now all the pci goodies ... */
......@@ -2601,9 +2586,7 @@ static int net2280_probe (struct pci_dev *pdev, const struct pci_device_id *id)
, &dev->pci->pcimstctl);
/* erratum 0115 shouldn't appear: Linux inits PCI_LATENCY_TIMER */
pci_set_master (pdev);
#ifdef HAVE_PCI_SET_MWI
pci_set_mwi (pdev);
#endif
/* ... also flushes any posted pci writes */
dev->chiprev = get_idx_reg (dev->regs, REG_CHIPREV) & 0xffff;
......
......@@ -11,7 +11,7 @@
#include <linux/kernel.h>
#include <linux/list.h>
#include <linux/string.h>
#include <linux/version.h>
#include <linux/device.h>
#include <linux/usb_ch9.h>
#include <linux/usb_gadget.h>
......
......@@ -77,6 +77,8 @@
#include <linux/interrupt.h>
#include <linux/uts.h>
#include <linux/version.h>
#include <linux/device.h>
#include <linux/moduleparam.h>
#include <asm/byteorder.h>
#include <asm/io.h>
......@@ -259,14 +261,8 @@ struct zero_dev {
struct usb_ep *in_ep, *out_ep;
};
#ifdef HAVE_DRIVER_MODEL
#define xprintk(dev,level,fmt,args...) \
dev_printk(level , &dev->gadget->dev , fmt , ## args)
#else
#define xprintk(dev,level,fmt,args...) \
printk(level "%s %s: " fmt , shortname, dev->gadget->dev.bus_id, \
## args)
#endif /* HAVE_DRIVER_MODEL */
#define xprintk(d,level,fmt,args...) \
dev_printk(level , &(d)->gadget->dev , fmt , ## args)
#ifdef DEBUG
#undef DEBUG
......@@ -296,6 +292,9 @@ struct zero_dev {
static unsigned buflen = 4096;
static unsigned qlen = 32;
module_param (buflen, uint, S_IRUGO|S_IWUSR);
module_param (qlen, uint, S_IRUGO|S_IWUSR);
/*
* Normally the "loopback" configuration is second (index 1) so
* it's not the default. Here's where to change that order, to
......@@ -304,25 +303,7 @@ static unsigned qlen = 32;
*/
static int loopdefault = 0;
#ifdef HAVE_DRIVER_MODEL
#include <linux/moduleparam.h>
module_param (buflen, uint, 0);
module_param (qlen, uint, 0);
module_param (loopdefault, bool, 0);
#else
MODULE_PARM (buflen, "i");
MODULE_PARM_DESC (buflen, "size of i/o buffers");
MODULE_PARM (qlen, "i");
MODULE_PARM_DESC (qlen, "depth of loopback buffering");
MODULE_PARM (loopdefault, "b");
MODULE_PARM_DESC (loopdefault, "true to have default config be loopback");
#endif /* HAVE_DRIVER_MODEL */
module_param (loopdefault, bool, S_IRUGO|S_IWUSR);
/*-------------------------------------------------------------------------*/
......@@ -984,12 +965,10 @@ zero_set_config (struct zero_dev *dev, unsigned number, int gfp_flags)
static void zero_setup_complete (struct usb_ep *ep, struct usb_request *req)
{
if (req->status || req->actual != req->length) {
struct zero_dev *dev = ep->driver_data;
DEBUG (dev, "setup complete --> %d, %d/%d\n",
if (req->status || req->actual != req->length)
DEBUG ((struct zero_dev *) ep->driver_data,
"setup complete --> %d, %d/%d\n",
req->status, req->actual, req->length);
}
}
/*
......
......@@ -435,11 +435,6 @@ struct usb_gadget_ops {
unsigned code, unsigned long param);
};
#if LINUX_VERSION_CODE > KERNEL_VERSION(2,5,50)
#define HAVE_DRIVER_MODEL
#include <linux/device.h>
#endif
/**
* struct usb_gadget - represents a usb slave device
* @ep0: Endpoint zero, used when reading or writing responses to
......@@ -469,47 +464,21 @@ struct usb_gadget {
enum usb_device_speed speed;
const char *name;
#ifdef HAVE_DRIVER_MODEL
/* with 2.5 "generic dma" api, use this to allocate dma-coherent
* buffers or set up dma mappings. or print diagnostics, etc.
/* use this to allocate dma-coherent buffers or set up
* dma mappings. or print diagnostics, etc.
*/
struct device dev;
#else
struct __gadget_device {
char *bus_id;
void *driver_data;
} dev;
#endif
};
#ifdef HAVE_DRIVER_MODEL
static inline void set_gadget_data (struct usb_gadget *gadget, void *data)
{ dev_set_drvdata (&gadget->dev, data); }
static inline void *get_gadget_data (struct usb_gadget *gadget)
{ return dev_get_drvdata (&gadget->dev); }
#else
static inline void set_gadget_data (struct usb_gadget *gadget, void *data)
{ gadget->dev.driver_data = data; }
static inline void *get_gadget_data (struct usb_gadget *gadget)
{ return gadget->dev.driver_data; }
#endif
/* iterates the non-control endpoints; 'tmp' is a struct usb_ep pointer */
#define gadget_for_each_ep(tmp,gadget) \
list_for_each_entry(tmp, &(gadget)->ep_list, ep_list)
#ifndef list_for_each_entry
/* not available in 2.4.18 */
#define list_for_each_entry(pos, head, member) \
for (pos = list_entry((head)->next, typeof(*pos), member), \
prefetch(pos->member.next); \
&pos->member != (head); \
pos = list_entry(pos->member.next, typeof(*pos), member), \
prefetch(pos->member.next))
#endif
/**
* usb_gadget_frame_number - returns the current frame number
......@@ -649,14 +618,7 @@ struct usb_gadget_driver {
void (*resume)(struct usb_gadget *);
// FIXME support safe rmmod
#ifdef HAVE_DRIVER_MODEL
struct device_driver driver;
#else
struct __gadget_driver {
char *name;
void *driver_data;
} driver;
#endif
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment