Commit 41bc0ddb authored by David S. Miller's avatar David S. Miller

Merge branch 'net-dsa-microchip-add-KSZ9893-switch-support'

Tristram Ha says:

====================
net: dsa: microchip: add KSZ9893 switch support

This series of patches is to modify the KSZ9477 DSA driver to support
running KSZ9893 switch.

The KSZ9893 switch is similar to KSZ9477 except the ingress tail tag has
1 byte instead of 2 bytes.  The XMII register that governs the MAC
communication also has different register definitions.

v1
- Put KSZ9893 tagging in separate patch
- Remove other switch support
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parents d5fa9c55 8c29bebb
......@@ -7,6 +7,11 @@ Required properties:
of the following:
- "microchip,ksz9477"
- "microchip,ksz9897"
- "microchip,ksz9896"
- "microchip,ksz9567"
- "microchip,ksz8565"
- "microchip,ksz9893"
- "microchip,ksz9563"
Optional properties:
......@@ -73,4 +78,42 @@ Ethernet switch connected via SPI to the host, CPU port wired to eth0:
};
};
};
ksz8565: ksz8565@0 {
compatible = "microchip,ksz8565";
reg = <0>;
spi-max-frequency = <44000000>;
spi-cpha;
spi-cpol;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "lan1";
};
port@1 {
reg = <1>;
label = "lan2";
};
port@2 {
reg = <2>;
label = "lan3";
};
port@3 {
reg = <3>;
label = "lan4";
};
port@6 {
reg = <6>;
label = "cpu";
ethernet = <&eth0>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};
};
......@@ -18,6 +18,11 @@
#include "ksz9477_reg.h"
#include "ksz_common.h"
/* Used with variable features to indicate capabilities. */
#define GBIT_SUPPORT BIT(0)
#define NEW_XMII BIT(1)
#define IS_9893 BIT(2)
static const struct {
int index;
char string[ETH_GSTRING_LEN];
......@@ -328,7 +333,12 @@ static void ksz9477_port_init_cnt(struct ksz_device *dev, int port)
static enum dsa_tag_protocol ksz9477_get_tag_protocol(struct dsa_switch *ds,
int port)
{
return DSA_TAG_PROTO_KSZ9477;
enum dsa_tag_protocol proto = DSA_TAG_PROTO_KSZ9477;
struct ksz_device *dev = ds->priv;
if (dev->features & IS_9893)
proto = DSA_TAG_PROTO_KSZ9893;
return proto;
}
static int ksz9477_phy_read16(struct dsa_switch *ds, int addr, int reg)
......@@ -389,6 +399,10 @@ static int ksz9477_phy_write16(struct dsa_switch *ds, int addr, int reg,
/* No real PHY after this. */
if (addr >= dev->phy_port_cnt)
return 0;
/* No gigabit support. Do not write to this register. */
if (!(dev->features & GBIT_SUPPORT) && reg == MII_CTRL1000)
return 0;
ksz_pwrite16(dev, addr, 0x100 + (reg << 1), val);
return 0;
......@@ -998,11 +1012,156 @@ static void ksz9477_port_mirror_del(struct dsa_switch *ds, int port,
static void ksz9477_phy_setup(struct ksz_device *dev, int port,
struct phy_device *phy)
{
if (port < dev->phy_port_cnt) {
/* Only apply to port with PHY. */
if (port >= dev->phy_port_cnt)
return;
/* The MAC actually cannot run in 1000 half-duplex mode. */
phy_remove_link_mode(phy,
ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
/* PHY does not support gigabit. */
if (!(dev->features & GBIT_SUPPORT))
phy_remove_link_mode(phy,
ETHTOOL_LINK_MODE_1000baseT_Full_BIT);
}
static bool ksz9477_get_gbit(struct ksz_device *dev, u8 data)
{
bool gbit;
if (dev->features & NEW_XMII)
gbit = !(data & PORT_MII_NOT_1GBIT);
else
gbit = !!(data & PORT_MII_1000MBIT_S1);
return gbit;
}
static void ksz9477_set_gbit(struct ksz_device *dev, bool gbit, u8 *data)
{
if (dev->features & NEW_XMII) {
if (gbit)
*data &= ~PORT_MII_NOT_1GBIT;
else
*data |= PORT_MII_NOT_1GBIT;
} else {
if (gbit)
*data |= PORT_MII_1000MBIT_S1;
else
*data &= ~PORT_MII_1000MBIT_S1;
}
}
static int ksz9477_get_xmii(struct ksz_device *dev, u8 data)
{
int mode;
if (dev->features & NEW_XMII) {
switch (data & PORT_MII_SEL_M) {
case PORT_MII_SEL:
mode = 0;
break;
case PORT_RMII_SEL:
mode = 1;
break;
case PORT_GMII_SEL:
mode = 2;
break;
default:
mode = 3;
}
} else {
switch (data & PORT_MII_SEL_M) {
case PORT_MII_SEL_S1:
mode = 0;
break;
case PORT_RMII_SEL_S1:
mode = 1;
break;
case PORT_GMII_SEL_S1:
mode = 2;
break;
default:
mode = 3;
}
}
return mode;
}
static void ksz9477_set_xmii(struct ksz_device *dev, int mode, u8 *data)
{
u8 xmii;
if (dev->features & NEW_XMII) {
switch (mode) {
case 0:
xmii = PORT_MII_SEL;
break;
case 1:
xmii = PORT_RMII_SEL;
break;
case 2:
xmii = PORT_GMII_SEL;
break;
default:
xmii = PORT_RGMII_SEL;
break;
}
} else {
switch (mode) {
case 0:
xmii = PORT_MII_SEL_S1;
break;
case 1:
xmii = PORT_RMII_SEL_S1;
break;
case 2:
xmii = PORT_GMII_SEL_S1;
break;
default:
xmii = PORT_RGMII_SEL_S1;
break;
}
}
*data &= ~PORT_MII_SEL_M;
*data |= xmii;
}
static phy_interface_t ksz9477_get_interface(struct ksz_device *dev, int port)
{
phy_interface_t interface;
bool gbit;
int mode;
u8 data8;
if (port < dev->phy_port_cnt)
return PHY_INTERFACE_MODE_NA;
ksz_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8);
gbit = ksz9477_get_gbit(dev, data8);
mode = ksz9477_get_xmii(dev, data8);
switch (mode) {
case 2:
interface = PHY_INTERFACE_MODE_GMII;
if (gbit)
break;
case 0:
interface = PHY_INTERFACE_MODE_MII;
break;
case 1:
interface = PHY_INTERFACE_MODE_RMII;
break;
default:
interface = PHY_INTERFACE_MODE_RGMII;
if (data8 & PORT_RGMII_ID_EG_ENABLE)
interface = PHY_INTERFACE_MODE_RGMII_TXID;
if (data8 & PORT_RGMII_ID_IG_ENABLE) {
interface = PHY_INTERFACE_MODE_RGMII_RXID;
if (data8 & PORT_RGMII_ID_EG_ENABLE)
interface = PHY_INTERFACE_MODE_RGMII_ID;
}
break;
}
return interface;
}
static void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
......@@ -1051,24 +1210,25 @@ static void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
/* configure MAC to 1G & RGMII mode */
ksz_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8);
data8 &= ~PORT_MII_NOT_1GBIT;
data8 &= ~PORT_MII_SEL_M;
switch (dev->interface) {
case PHY_INTERFACE_MODE_MII:
data8 |= PORT_MII_NOT_1GBIT;
data8 |= PORT_MII_SEL;
ksz9477_set_xmii(dev, 0, &data8);
ksz9477_set_gbit(dev, false, &data8);
p->phydev.speed = SPEED_100;
break;
case PHY_INTERFACE_MODE_RMII:
data8 |= PORT_MII_NOT_1GBIT;
data8 |= PORT_RMII_SEL;
ksz9477_set_xmii(dev, 1, &data8);
ksz9477_set_gbit(dev, false, &data8);
p->phydev.speed = SPEED_100;
break;
case PHY_INTERFACE_MODE_GMII:
data8 |= PORT_GMII_SEL;
ksz9477_set_xmii(dev, 2, &data8);
ksz9477_set_gbit(dev, true, &data8);
p->phydev.speed = SPEED_1000;
break;
default:
ksz9477_set_xmii(dev, 3, &data8);
ksz9477_set_gbit(dev, true, &data8);
data8 &= ~PORT_RGMII_ID_IG_ENABLE;
data8 &= ~PORT_RGMII_ID_EG_ENABLE;
if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
......@@ -1077,7 +1237,6 @@ static void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
dev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
data8 |= PORT_RGMII_ID_EG_ENABLE;
data8 |= PORT_RGMII_SEL;
p->phydev.speed = SPEED_1000;
break;
}
......@@ -1115,10 +1274,25 @@ static void ksz9477_config_cpu_port(struct dsa_switch *ds)
for (i = 0; i < dev->port_cnt; i++) {
if (dsa_is_cpu_port(ds, i) && (dev->cpu_ports & (1 << i))) {
phy_interface_t interface;
dev->cpu_port = i;
dev->host_mask = (1 << dev->cpu_port);
dev->port_mask |= dev->host_mask;
/* Read from XMII register to determine host port
* interface. If set specifically in device tree
* note the difference to help debugging.
*/
interface = ksz9477_get_interface(dev, i);
if (!dev->interface)
dev->interface = interface;
if (interface && interface != dev->interface)
dev_info(dev->dev,
"use %s instead of %s\n",
phy_modes(dev->interface),
phy_modes(interface));
/* enable cpu port */
ksz9477_port_setup(dev, i, true);
p = &dev->ports[dev->cpu_port];
......@@ -1172,6 +1346,9 @@ static int ksz9477_setup(struct dsa_switch *ds)
ksz9477_cfg32(dev, REG_SW_QM_CTRL__4, UNICAST_VLAN_BOUNDARY,
true);
/* Do not work correctly with tail tagging. */
ksz_cfg(dev, REG_SW_MAC_CTRL_0, SW_CHECK_LENGTH, false);
/* accept packet up to 2000bytes */
ksz_cfg(dev, REG_SW_MAC_CTRL_1, SW_LEGAL_PACKET_DISABLE, true);
......@@ -1230,6 +1407,8 @@ static u32 ksz9477_get_port_addr(int port, int offset)
static int ksz9477_switch_detect(struct ksz_device *dev)
{
u8 data8;
u8 id_hi;
u8 id_lo;
u32 id32;
int ret;
......@@ -1245,6 +1424,9 @@ static int ksz9477_switch_detect(struct ksz_device *dev)
/* read chip id */
ret = ksz_read32(dev, REG_CHIP_ID0__1, &id32);
if (ret)
return ret;
ret = ksz_read8(dev, REG_GLOBAL_OPTIONS, &data8);
if (ret)
return ret;
......@@ -1252,6 +1434,32 @@ static int ksz9477_switch_detect(struct ksz_device *dev)
dev->mib_port_cnt = TOTAL_PORT_NUM;
dev->phy_port_cnt = 5;
/* Default capability is gigabit capable. */
dev->features = GBIT_SUPPORT;
id_hi = (u8)(id32 >> 16);
id_lo = (u8)(id32 >> 8);
if ((id_lo & 0xf) == 3) {
/* Chip is from KSZ9893 design. */
dev->features |= IS_9893;
/* Chip does not support gigabit. */
if (data8 & SW_QW_ABLE)
dev->features &= ~GBIT_SUPPORT;
dev->mib_port_cnt = 3;
dev->phy_port_cnt = 2;
} else {
/* Chip uses new XMII register definitions. */
dev->features |= NEW_XMII;
/* Chip does not support gigabit. */
if (!(data8 & SW_GIGABIT_ABLE))
dev->features &= ~GBIT_SUPPORT;
}
/* Change chip id to known ones so it can be matched against them. */
id32 = (id_hi << 16) | (id_lo << 8);
dev->chip_id = id32;
return 0;
......@@ -1286,6 +1494,15 @@ static const struct ksz_chip_data ksz9477_switch_chips[] = {
.cpu_ports = 0x7F, /* can be configured as cpu port */
.port_cnt = 7, /* total physical port count */
},
{
.chip_id = 0x00989300,
.dev_name = "KSZ9893",
.num_vlans = 4096,
.num_alus = 4096,
.num_statics = 16,
.cpu_ports = 0x07, /* can be configured as cpu port */
.port_cnt = 3, /* total port count */
},
};
static int ksz9477_switch_init(struct ksz_device *dev)
......@@ -1333,7 +1550,6 @@ static int ksz9477_switch_init(struct ksz_device *dev)
if (!dev->ports[i].mib.counters)
return -ENOMEM;
}
dev->interface = PHY_INTERFACE_MODE_RGMII_TXID;
return 0;
}
......
......@@ -2,7 +2,7 @@
/*
* Microchip KSZ9477 series register access through SPI
*
* Copyright (C) 2017-2018 Microchip Technology Inc.
* Copyright (C) 2017-2019 Microchip Technology Inc.
*/
#include <asm/unaligned.h>
......@@ -155,6 +155,8 @@ static void ksz9477_spi_shutdown(struct spi_device *spi)
static const struct of_device_id ksz9477_dt_ids[] = {
{ .compatible = "microchip,ksz9477" },
{ .compatible = "microchip,ksz9897" },
{ .compatible = "microchip,ksz9893" },
{ .compatible = "microchip,ksz9563" },
{},
};
MODULE_DEVICE_TABLE(of, ksz9477_dt_ids);
......
......@@ -453,7 +453,9 @@ int ksz_switch_register(struct ksz_device *dev,
if (ret)
return ret;
dev->interface = PHY_INTERFACE_MODE_MII;
/* Host port interface will be self detected, or specifically set in
* device tree.
*/
if (dev->dev->of_node) {
ret = of_get_phy_mode(dev->dev->of_node);
if (ret >= 0)
......
......@@ -38,6 +38,7 @@ enum dsa_tag_protocol {
DSA_TAG_PROTO_EDSA,
DSA_TAG_PROTO_GSWIP,
DSA_TAG_PROTO_KSZ9477,
DSA_TAG_PROTO_KSZ9893,
DSA_TAG_PROTO_LAN9303,
DSA_TAG_PROTO_MTK,
DSA_TAG_PROTO_QCA,
......
......@@ -57,6 +57,7 @@ const struct dsa_device_ops *dsa_device_ops[DSA_TAG_LAST] = {
#endif
#ifdef CONFIG_NET_DSA_TAG_KSZ9477
[DSA_TAG_PROTO_KSZ9477] = &ksz9477_netdev_ops,
[DSA_TAG_PROTO_KSZ9893] = &ksz9893_netdev_ops,
#endif
#ifdef CONFIG_NET_DSA_TAG_LAN9303
[DSA_TAG_PROTO_LAN9303] = &lan9303_netdev_ops,
......@@ -93,6 +94,7 @@ const char *dsa_tag_protocol_to_str(const struct dsa_device_ops *ops)
#endif
#ifdef CONFIG_NET_DSA_TAG_KSZ9477
[DSA_TAG_PROTO_KSZ9477] = "ksz9477",
[DSA_TAG_PROTO_KSZ9893] = "ksz9893",
#endif
#ifdef CONFIG_NET_DSA_TAG_LAN9303
[DSA_TAG_PROTO_LAN9303] = "lan9303",
......
......@@ -216,6 +216,7 @@ extern const struct dsa_device_ops gswip_netdev_ops;
/* tag_ksz.c */
extern const struct dsa_device_ops ksz9477_netdev_ops;
extern const struct dsa_device_ops ksz9893_netdev_ops;
/* tag_lan9303.c */
extern const struct dsa_device_ops lan9303_netdev_ops;
......
......@@ -16,6 +16,7 @@
/* Typically only one byte is used for tail tag. */
#define KSZ_EGRESS_TAG_LEN 1
#define KSZ_INGRESS_TAG_LEN 1
static struct sk_buff *ksz_common_xmit(struct sk_buff *skb,
struct net_device *dev, int len)
......@@ -141,3 +142,36 @@ const struct dsa_device_ops ksz9477_netdev_ops = {
.rcv = ksz9477_rcv,
.overhead = KSZ9477_INGRESS_TAG_LEN,
};
#define KSZ9893_TAIL_TAG_OVERRIDE BIT(5)
#define KSZ9893_TAIL_TAG_LOOKUP BIT(6)
static struct sk_buff *ksz9893_xmit(struct sk_buff *skb,
struct net_device *dev)
{
struct dsa_port *dp = dsa_slave_to_port(dev);
struct sk_buff *nskb;
u8 *addr;
u8 *tag;
nskb = ksz_common_xmit(skb, dev, KSZ_INGRESS_TAG_LEN);
if (!nskb)
return NULL;
/* Tag encoding */
tag = skb_put(nskb, KSZ_INGRESS_TAG_LEN);
addr = skb_mac_header(nskb);
*tag = BIT(dp->index);
if (is_link_local_ether_addr(addr))
*tag |= KSZ9893_TAIL_TAG_OVERRIDE;
return nskb;
}
const struct dsa_device_ops ksz9893_netdev_ops = {
.xmit = ksz9893_xmit,
.rcv = ksz9477_rcv,
.overhead = KSZ_INGRESS_TAG_LEN,
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment