Commit 4406433d authored by Ludovic Desroches's avatar Ludovic Desroches Committed by Ulf Hansson

mmc: sdhci-of-at91: add presets setup

The controller claims to support SDR104. In fact, it only supports a
degraded SDR104 since the maximum frequency of the SD clock is 120 MHz
instead of 208 MHz.
The sdhci core is unaware of it and will compute a wrong clock divider.
We can deal with this specific case by using presets.
Signed-off-by: default avatarLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: default avatarAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: default avatarUlf Hansson <ulf.hansson@linaro.org>
parent 488aab3d
......@@ -18,6 +18,7 @@
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/mmc/host.h>
#include <linux/mmc/slot-gpio.h>
#include <linux/module.h>
......@@ -32,6 +33,8 @@
#define SDMMC_CACR_CAPWREN BIT(0)
#define SDMMC_CACR_KEY (0x46 << 8)
#define SDHCI_AT91_PRESET_COMMON_CONF 0x400 /* drv type B, programmable clock mode */
struct sdhci_at91_priv {
struct clk *hclock;
struct clk *gck;
......@@ -163,6 +166,7 @@ static int sdhci_at91_probe(struct platform_device *pdev)
unsigned int clk_base, clk_mul;
unsigned int gck_rate, real_gck_rate;
int ret;
unsigned int preset_div;
match = of_match_device(sdhci_at91_dt_match, &pdev->dev);
if (!match)
......@@ -230,6 +234,28 @@ static int sdhci_at91_probe(struct platform_device *pdev)
clk_mul, real_gck_rate);
}
/*
* We have to set preset values because it depends on the clk_mul
* value. Moreover, SDR104 is supported in a degraded mode since the
* maximum sd clock value is 120 MHz instead of 208 MHz. For that
* reason, we need to use presets to support SDR104.
*/
preset_div = DIV_ROUND_UP(real_gck_rate, 24000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_SDR12);
preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_SDR25);
preset_div = DIV_ROUND_UP(real_gck_rate, 100000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_SDR50);
preset_div = DIV_ROUND_UP(real_gck_rate, 120000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_SDR104);
preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
host->ioaddr + SDHCI_PRESET_FOR_DDR50);
clk_prepare_enable(priv->mainck);
clk_prepare_enable(priv->gck);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment