Merge branch 'for-4.20/dt-bindings' into for-4.20/soc

Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt

@@ -34,3 +34,96 @@ Board DTS:
 	pmc@c360000 {
 		nvidia,invert-interrupt;
 	};
+
+== Pad Control ==
+
+On Tegra SoCs a pad is a set of pins which are configured as a group.
+The pin grouping is a fixed attribute of the hardware. The PMC can be
+used to set pad power state and signaling voltage. A pad can be either
+in active or power down mode. The support for power state and signaling
+voltage configuration varies depending on the pad in question. 3.3 V and
+1.8 V signaling voltages are supported on pins where software
+controllable signaling voltage switching is available.
+
+Pad configurations are described with pin configuration nodes which
+are placed under the pmc node and they are referred to by the pinctrl
+client properties. For more information see
+Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
+
+The following pads are present on Tegra186:
+csia		csib		dsi		mipi-bias
+pex-clk-bias	pex-clk3	pex-clk2	pex-clk1
+usb0		usb1		usb2		usb-bias
+uart		audio		hsic		dbg
+hdmi-dp0	hdmi-dp1	pex-cntrl	sdmmc2-hv
+sdmmc4		cam		dsib		dsic
+dsid		csic		csid		csie
+dsif		spi		ufs		dmic-hv
+edp		sdmmc1-hv	sdmmc3-hv	conn
+audio-hv	ao-hv
+
+Required pin configuration properties:
+  - pins: A list of strings, each of which contains the name of a pad
+	  to be configured.
+
+Optional pin configuration properties:
+  - low-power-enable: Configure the pad into power down mode
+  - low-power-disable: Configure the pad into active mode
+  - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or
+    TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
+    The values are defined in
+    include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
+
+Note: The power state can be configured on all of the above pads except
+      for ao-hv. Following pads have software configurable signaling
+      voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv, audio-hv,
+      ao-hv.
+
+Pad configuration state example:
+	pmc: pmc@7000e400 {
+		compatible = "nvidia,tegra186-pmc";
+		reg = <0 0x0c360000 0 0x10000>,
+		      <0 0x0c370000 0 0x10000>,
+		      <0 0x0c380000 0 0x10000>,
+		      <0 0x0c390000 0 0x10000>;
+		reg-names = "pmc", "wake", "aotag", "scratch";
+
+		...
+
+		sdmmc1_3v3: sdmmc1-3v3 {
+			pins = "sdmmc1-hv";
+			power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
+		};
+
+		sdmmc1_1v8: sdmmc1-1v8 {
+			pins = "sdmmc1-hv";
+			power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
+		};
+
+		hdmi_off: hdmi-off {
+			pins = "hdmi";
+			low-power-enable;
+		}
+
+		hdmi_on: hdmi-on {
+			pins = "hdmi";
+			low-power-disable;
+		}
+	};
+
+Pinctrl client example:
+	sdmmc1: sdhci@3400000 {
+		...
+		pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+		pinctrl-0 = <&sdmmc1_3v3>;
+		pinctrl-1 = <&sdmmc1_1v8>;
+	};
+
+	...
+
+	sor0: sor@15540000 {
+		...
+		pinctrl-0 = <&hdmi_off>;
+		pinctrl-1 = <&hdmi_on>;
+		pinctrl-names = "hdmi-on", "hdmi-off";
+	};

Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt

@@ -195,3 +195,106 @@ Example:
 		power-domains = <&pd_audio>;
 		...
 	};
+
+== Pad Control ==
+
+On Tegra SoCs a pad is a set of pins which are configured as a group.
+The pin grouping is a fixed attribute of the hardware. The PMC can be
+used to set pad power state and signaling voltage. A pad can be either
+in active or power down mode. The support for power state and signaling
+voltage configuration varies depending on the pad in question. 3.3 V and
+1.8 V signaling voltages are supported on pins where software
+controllable signaling voltage switching is available.
+
+The pad configuration state nodes are placed under the pmc node and they
+are referred to by the pinctrl client properties. For more information
+see Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
+The pad name should be used as the value of the pins property in pin
+configuration nodes.
+
+The following pads are present on Tegra124 and Tegra132:
+audio		bb		cam		comp
+csia		csb		cse		dsi
+dsib		dsic		dsid		hdmi
+hsic		hv		lvds		mipi-bias
+nand		pex-bias	pex-clk1	pex-clk2
+pex-cntrl	sdmmc1		sdmmc3		sdmmc4
+sys_ddc		uart		usb0		usb1
+usb2		usb_bias
+
+The following pads are present on Tegra210:
+audio		audio-hv	cam		csia
+csib		csic		csid		csie
+csif		dbg		debug-nonao	dmic
+dp		dsi		dsib		dsic
+dsid		emmc		emmc2		gpio
+hdmi		hsic		lvds		mipi-bias
+pex-bias	pex-clk1	pex-clk2	pex-cntrl
+sdmmc1		sdmmc3		spi		spi-hv
+uart		usb0		usb1		usb2
+usb3		usb-bias
+
+Required pin configuration properties:
+  - pins: Must contain name of the pad(s) to be configured.
+
+Optional pin configuration properties:
+  - low-power-enable: Configure the pad into power down mode
+  - low-power-disable: Configure the pad into active mode
+  - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8
+    or TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
+    The values are defined in
+    include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
+
+Note: The power state can be configured on all of the Tegra124 and
+      Tegra132 pads. None of the Tegra124 or Tegra132 pads support
+      signaling voltage switching.
+
+Note: All of the listed Tegra210 pads except pex-cntrl support power
+      state configuration. Signaling voltage switching is supported on
+      following Tegra210 pads: audio, audio-hv, cam, dbg, dmic, gpio,
+      pex-cntrl, sdmmc1, sdmmc3, spi, spi-hv, and uart.
+
+Pad configuration state example:
+	pmc: pmc@7000e400 {
+		compatible = "nvidia,tegra210-pmc";
+		reg = <0x0 0x7000e400 0x0 0x400>;
+		clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>;
+		clock-names = "pclk", "clk32k_in";
+
+		...
+
+		sdmmc1_3v3: sdmmc1-3v3 {
+			pins = "sdmmc1";
+			power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
+		};
+
+		sdmmc1_1v8: sdmmc1-1v8 {
+			pins = "sdmmc1";
+			power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
+		};
+
+		hdmi_off: hdmi-off {
+			pins = "hdmi";
+			low-power-enable;
+		}
+
+		hdmi_on: hdmi-on {
+			pins = "hdmi";
+			low-power-disable;
+		}
+	};
+
+Pinctrl client example:
+	sdmmc1: sdhci@700b0000 {
+		...
+		pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+		pinctrl-0 = <&sdmmc1_3v3>;
+		pinctrl-1 = <&sdmmc1_1v8>;
+	};
+	...
+	sor@54540000 {
+		...
+		pinctrl-0 = <&hdmi_off>;
+		pinctrl-1 = <&hdmi_on>;
+		pinctrl-names = "hdmi-on", "hdmi-off";
+	};

include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * pinctrl-tegra-io-pad.h: Tegra I/O pad source voltage configuration constants
+ * pinctrl bindings.
+ *
+ * Copyright (c) 2018, NVIDIA CORPORATION.  All rights reserved.
+ *
+ * Author: Aapo Vienamo <avienamo@nvidia.com>
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_TEGRA_IO_PAD_H
+#define _DT_BINDINGS_PINCTRL_TEGRA_IO_PAD_H
+
+/* Voltage levels of the I/O pad's source rail */
+#define TEGRA_IO_PAD_VOLTAGE_1V8	0
+#define TEGRA_IO_PAD_VOLTAGE_3V3	1
+
+#endif