Skip to content

L
linux
Commit 4de10b18 authored by Wey-Yi Guy's avatar Wey-Yi Guy Committed by John W. Linville
Browse files
Options

iwlagn: remove more 3945/4965 related defines 

After driver split, remove unused #defines
Signed-off-by: default avatarWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
parent 7102762e
Show whitespace changes
Inline Side-by-side
Showing with 0 additions and 327 deletions
drivers/net/wireless/iwlwifi/iwl-prph.h
View file @ 4de10b18
......@@ -97,142 +97,6 @@
#define APMG_PCIDEV_STT_VAL_L1_ACT_DIS (0x00000800)
/**
* BSM (Bootstrap State Machine)
*
* The Bootstrap State Machine (BSM) stores a short bootstrap uCode program
* in special SRAM that does not power down when the embedded control
* processor is sleeping (e.g. for periodic power-saving shutdowns of radio).
*
* When powering back up after sleeps (or during initial uCode load), the BSM
* internally loads the short bootstrap program from the special SRAM into the
* embedded processor's instruction SRAM, and starts the processor so it runs
* the bootstrap program.
*
* This bootstrap program loads (via PCI busmaster DMA) instructions and data
* images for a uCode program from host DRAM locations. The host driver
* indicates DRAM locations and sizes for instruction and data images via the
* four BSM_DRAM_* registers. Once the bootstrap program loads the new program,
* the new program starts automatically.
*
* The uCode used for open-source drivers includes two programs:
*
* 1) Initialization -- performs hardware calibration and sets up some
* internal data, then notifies host via "initialize alive" notification
* (struct iwl_init_alive_resp) that it has completed all of its work.
* After signal from host, it then loads and starts the runtime program.
* The initialization program must be used when initially setting up the
* NIC after loading the driver.
*
* 2) Runtime/Protocol -- performs all normal runtime operations. This
* notifies host via "alive" notification (struct iwl_alive_resp) that it
* is ready to be used.
*
* When initializing the NIC, the host driver does the following procedure:
*
* 1) Load bootstrap program (instructions only, no data image for bootstrap)
* into bootstrap memory. Use dword writes starting at BSM_SRAM_LOWER_BOUND
*
* 2) Point (via BSM_DRAM_*) to the "initialize" uCode data and instruction
* images in host DRAM.
*
* 3) Set up BSM to copy from BSM SRAM into uCode instruction SRAM when asked:
* BSM_WR_MEM_SRC_REG = 0
* BSM_WR_MEM_DST_REG = RTC_INST_LOWER_BOUND
* BSM_WR_MEM_DWCOUNT_REG = # dwords in bootstrap instruction image
*
* 4) Load bootstrap into instruction SRAM:
* BSM_WR_CTRL_REG = BSM_WR_CTRL_REG_BIT_START
*
* 5) Wait for load completion:
* Poll BSM_WR_CTRL_REG for BSM_WR_CTRL_REG_BIT_START = 0
*
* 6) Enable future boot loads whenever NIC's power management triggers it:
* BSM_WR_CTRL_REG = BSM_WR_CTRL_REG_BIT_START_EN
*
* 7) Start the NIC by removing all reset bits:
* CSR_RESET = 0
*
* The bootstrap uCode (already in instruction SRAM) loads initialization
* uCode. Initialization uCode performs data initialization, sends
* "initialize alive" notification to host, and waits for a signal from
* host to load runtime code.
*
* 4) Point (via BSM_DRAM_*) to the "runtime" uCode data and instruction
* images in host DRAM. The last register loaded must be the instruction
* byte count register ("1" in MSbit tells initialization uCode to load
* the runtime uCode):
* BSM_DRAM_INST_BYTECOUNT_REG = byte count | BSM_DRAM_INST_LOAD
*
* 5) Wait for "alive" notification, then issue normal runtime commands.
*
* Data caching during power-downs:
*
* Just before the embedded controller powers down (e.g for automatic
* power-saving modes, or for RFKILL), uCode stores (via PCI busmaster DMA)
* a current snapshot of the embedded processor's data SRAM into host DRAM.
* This caches the data while the embedded processor's memory is powered down.
* Location and size are controlled by BSM_DRAM_DATA_* registers.
*
* NOTE: Instruction SRAM does not need to be saved, since that doesn't
* change during operation; the original image (from uCode distribution
* file) can be used for reload.
*
* When powering back up, the BSM loads the bootstrap program. Bootstrap looks
* at the BSM_DRAM_* registers, which now point to the runtime instruction
* image and the cached (modified) runtime data (*not* the initialization
* uCode). Bootstrap reloads these runtime images into SRAM, and restarts the
* uCode from where it left off before the power-down.
*
* NOTE: Initialization uCode does *not* run as part of the save/restore
* procedure.
*
* This save/restore method is mostly for autonomous power management during
* normal operation (result of POWER_TABLE_CMD). Platform suspend/resume and
* RFKILL should use complete restarts (with total re-initialization) of uCode,
* allowing total shutdown (including BSM memory).
*
* Note that, during normal operation, the host DRAM that held the initial
* startup data for the runtime code is now being used as a backup data cache
* for modified data! If you need to completely re-initialize the NIC, make
* sure that you use the runtime data image from the uCode distribution file,
* not the modified/saved runtime data. You may want to store a separate
* "clean" runtime data image in DRAM to avoid disk reads of distribution file.
*/
/* BSM bit fields */
#define BSM_WR_CTRL_REG_BIT_START (0x80000000) /* start boot load now */
#define BSM_WR_CTRL_REG_BIT_START_EN (0x40000000) /* enable boot after pwrup*/
#define BSM_DRAM_INST_LOAD (0x80000000) /* start program load now */
/* BSM addresses */
#define BSM_BASE (PRPH_BASE + 0x3400)
#define BSM_END (PRPH_BASE + 0x3800)
#define BSM_WR_CTRL_REG (BSM_BASE + 0x000) /* ctl and status */
#define BSM_WR_MEM_SRC_REG (BSM_BASE + 0x004) /* source in BSM mem */
#define BSM_WR_MEM_DST_REG (BSM_BASE + 0x008) /* dest in SRAM mem */
#define BSM_WR_DWCOUNT_REG (BSM_BASE + 0x00C) /* bytes */
#define BSM_WR_STATUS_REG (BSM_BASE + 0x010) /* bit 0: 1 == done */
/*
* Pointers and size regs for bootstrap load and data SRAM save/restore.
* NOTE: 3945 pointers use bits 31:0 of DRAM address.
* 4965 pointers use bits 35:4 of DRAM address.
*/
#define BSM_DRAM_INST_PTR_REG (BSM_BASE + 0x090)
#define BSM_DRAM_INST_BYTECOUNT_REG (BSM_BASE + 0x094)
#define BSM_DRAM_DATA_PTR_REG (BSM_BASE + 0x098)
#define BSM_DRAM_DATA_BYTECOUNT_REG (BSM_BASE + 0x09C)
/*
* BSM special memory, stays powered on during power-save sleeps.
* Read/write, address range from LOWER_BOUND to (LOWER_BOUND + SIZE -1)
*/
#define BSM_SRAM_LOWER_BOUND (PRPH_BASE + 0x3800)
#define BSM_SRAM_SIZE (1024) /* bytes */
/**
* Tx Scheduler
*
......@@ -319,201 +183,10 @@
* Max Tx window size is the max number of contiguous TFDs that the scheduler
* can keep track of at one time when creating block-ack chains of frames.
* Note that "64" matches the number of ack bits in a block-ack packet.
* Driver should use SCD_WIN_SIZE and SCD_FRAME_LIMIT values to initialize
* IWL49_SCD_CONTEXT_QUEUE_OFFSET(x) values.
*/
#define SCD_WIN_SIZE 64
#define SCD_FRAME_LIMIT 64
/* SCD registers are internal, must be accessed via HBUS_TARG_PRPH regs */
#define IWL49_SCD_START_OFFSET 0xa02c00
/*
* 4965 tells driver SRAM address for internal scheduler structs via this reg.
* Value is valid only after "Alive" response from uCode.
*/
#define IWL49_SCD_SRAM_BASE_ADDR (IWL49_SCD_START_OFFSET + 0x0)
/*
* Driver may need to update queue-empty bits after changing queue's
* write and read pointers (indexes) during (re-)initialization (i.e. when
* scheduler is not tracking what's happening).
* Bit fields:
* 31-16: Write mask -- 1: update empty bit, 0: don't change empty bit
* 15-00: Empty state, one for each queue -- 1: empty, 0: non-empty
* NOTE: This register is not used by Linux driver.
*/
#define IWL49_SCD_EMPTY_BITS (IWL49_SCD_START_OFFSET + 0x4)
/*
* Physical base address of array of byte count (BC) circular buffers (CBs).
* Each Tx queue has a BC CB in host DRAM to support Scheduler-ACK mode.
* This register points to BC CB for queue 0, must be on 1024-byte boundary.
* Others are spaced by 1024 bytes.
* Each BC CB is 2 bytes * (256 + 64) = 740 bytes, followed by 384 bytes pad.
* (Index into a queue's BC CB) = (index into queue's TFD CB) = (SSN & 0xff).
* Bit fields:
* 25-00: Byte Count CB physical address [35:10], must be 1024-byte aligned.
*/
#define IWL49_SCD_DRAM_BASE_ADDR (IWL49_SCD_START_OFFSET + 0x10)
/*
* Enables any/all Tx DMA/FIFO channels.
* Scheduler generates requests for only the active channels.
* Set this to 0xff to enable all 8 channels (normal usage).
* Bit fields:
* 7- 0: Enable (1), disable (0), one bit for each channel 0-7
*/
#define IWL49_SCD_TXFACT (IWL49_SCD_START_OFFSET + 0x1c)
/*
* Queue (x) Write Pointers (indexes, really!), one for each Tx queue.
* Initialized and updated by driver as new TFDs are added to queue.
* NOTE: If using Block Ack, index must correspond to frame's
* Start Sequence Number; index = (SSN & 0xff)
* NOTE: Alternative to HBUS_TARG_WRPTR, which is what Linux driver uses?
*/
#define IWL49_SCD_QUEUE_WRPTR(x) (IWL49_SCD_START_OFFSET + 0x24 + (x) * 4)
/*
* Queue (x) Read Pointers (indexes, really!), one for each Tx queue.
* For FIFO mode, index indicates next frame to transmit.
* For Scheduler-ACK mode, index indicates first frame in Tx window.
* Initialized by driver, updated by scheduler.
*/
#define IWL49_SCD_QUEUE_RDPTR(x) (IWL49_SCD_START_OFFSET + 0x64 + (x) * 4)
/*
* Select which queues work in chain mode (1) vs. not (0).
* Use chain mode to build chains of aggregated frames.
* Bit fields:
* 31-16: Reserved
* 15-00: Mode, one bit for each queue -- 1: Chain mode, 0: one-at-a-time
* NOTE: If driver sets up queue for chain mode, it should be also set up
* Scheduler-ACK mode as well, via SCD_QUEUE_STATUS_BITS(x).
*/
#define IWL49_SCD_QUEUECHAIN_SEL (IWL49_SCD_START_OFFSET + 0xd0)
/*
* Select which queues interrupt driver when scheduler increments
* a queue's read pointer (index).
* Bit fields:
* 31-16: Reserved
* 15-00: Interrupt enable, one bit for each queue -- 1: enabled, 0: disabled
* NOTE: This functionality is apparently a no-op; driver relies on interrupts
* from Rx queue to read Tx command responses and update Tx queues.
*/
#define IWL49_SCD_INTERRUPT_MASK (IWL49_SCD_START_OFFSET + 0xe4)
/*
* Queue search status registers. One for each queue.
* Sets up queue mode and assigns queue to Tx DMA channel.
* Bit fields:
* 19-10: Write mask/enable bits for bits 0-9
* 9: Driver should init to "0"
* 8: Scheduler-ACK mode (1), non-Scheduler-ACK (i.e. FIFO) mode (0).
* Driver should init to "1" for aggregation mode, or "0" otherwise.
* 7-6: Driver should init to "0"
* 5: Window Size Left; indicates whether scheduler can request
* another TFD, based on window size, etc. Driver should init
* this bit to "1" for aggregation mode, or "0" for non-agg.
* 4-1: Tx FIFO to use (range 0-7).
* 0: Queue is active (1), not active (0).
* Other bits should be written as "0"
*
* NOTE: If enabling Scheduler-ACK mode, chain mode should also be enabled
* via SCD_QUEUECHAIN_SEL.
*/
#define IWL49_SCD_QUEUE_STATUS_BITS(x)\
(IWL49_SCD_START_OFFSET + 0x104 + (x) * 4)
/* Bit field positions */
#define IWL49_SCD_QUEUE_STTS_REG_POS_ACTIVE (0)
#define IWL49_SCD_QUEUE_STTS_REG_POS_TXF (1)
#define IWL49_SCD_QUEUE_STTS_REG_POS_WSL (5)
#define IWL49_SCD_QUEUE_STTS_REG_POS_SCD_ACK (8)
/* Write masks */
#define IWL49_SCD_QUEUE_STTS_REG_POS_SCD_ACT_EN (10)
#define IWL49_SCD_QUEUE_STTS_REG_MSK (0x0007FC00)
/**
* 4965 internal SRAM structures for scheduler, shared with driver ...
*
* Driver should clear and initialize the following areas after receiving
* "Alive" response from 4965 uCode, i.e. after initial
* uCode load, or after a uCode load done for error recovery:
*
* SCD_CONTEXT_DATA_OFFSET (size 128 bytes)
* SCD_TX_STTS_BITMAP_OFFSET (size 256 bytes)
* SCD_TRANSLATE_TBL_OFFSET (size 32 bytes)
*
* Driver accesses SRAM via HBUS_TARG_MEM_* registers.
* Driver reads base address of this scheduler area from SCD_SRAM_BASE_ADDR.
* All OFFSET values must be added to this base address.
*/
/*
* Queue context. One 8-byte entry for each of 16 queues.
*
* Driver should clear this entire area (size 0x80) to 0 after receiving
* "Alive" notification from uCode. Additionally, driver should init
* each queue's entry as follows:
*
* LS Dword bit fields:
* 0-06: Max Tx window size for Scheduler-ACK. Driver should init to 64.
*
* MS Dword bit fields:
* 16-22: Frame limit. Driver should init to 10 (0xa).
*
* Driver should init all other bits to 0.
*
* Init must be done after driver receives "Alive" response from 4965 uCode,
* and when setting up queue for aggregation.
*/
#define IWL49_SCD_CONTEXT_DATA_OFFSET 0x380
#define IWL49_SCD_CONTEXT_QUEUE_OFFSET(x) \
(IWL49_SCD_CONTEXT_DATA_OFFSET + ((x) * 8))
#define IWL49_SCD_QUEUE_CTX_REG1_WIN_SIZE_POS (0)
#define IWL49_SCD_QUEUE_CTX_REG1_WIN_SIZE_MSK (0x0000007F)
#define IWL49_SCD_QUEUE_CTX_REG2_FRAME_LIMIT_POS (16)
#define IWL49_SCD_QUEUE_CTX_REG2_FRAME_LIMIT_MSK (0x007F0000)
/*
* Tx Status Bitmap
*
* Driver should clear this entire area (size 0x100) to 0 after receiving
* "Alive" notification from uCode. Area is used only by device itself;
* no other support (besides clearing) is required from driver.
*/
#define IWL49_SCD_TX_STTS_BITMAP_OFFSET 0x400
/*
* RAxTID to queue translation mapping.
*
* When queue is in Scheduler-ACK mode, frames placed in a that queue must be
* for only one combination of receiver address (RA) and traffic ID (TID), i.e.
* one QOS priority level destined for one station (for this wireless link,
* not final destination). The SCD_TRANSLATE_TABLE area provides 16 16-bit
* mappings, one for each of the 16 queues. If queue is not in Scheduler-ACK
* mode, the device ignores the mapping value.
*
* Bit fields, for each 16-bit map:
* 15-9: Reserved, set to 0
* 8-4: Index into device's station table for recipient station
* 3-0: Traffic ID (tid), range 0-15
*
* Driver should clear this entire area (size 32 bytes) to 0 after receiving
* "Alive" notification from uCode. To update a 16-bit map value, driver
* must read a dword-aligned value from device SRAM, replace the 16-bit map
* value of interest, and write the dword value back into device SRAM.
*/
#define IWL49_SCD_TRANSLATE_TBL_OFFSET 0x500
/* Find translation table dword to read/write for given queue */
#define IWL49_SCD_TRANSLATE_TBL_OFFSET_QUEUE(x) \
((IWL49_SCD_TRANSLATE_TBL_OFFSET + ((x) * 2)) & 0xfffffffc)
#define IWL_SCD_TXFIFO_POS_TID (0)
#define IWL_SCD_TXFIFO_POS_RA (4)
#define IWL_SCD_QUEUE_RA_TID_MAP_RATID_MSK (0x01FF)
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7