phy: add Rockchip Innosilicon hdmi phy

Add a driver for the Innosilicon hdmi phy used on rk3228/rk3229
and rk3328 socs from Rockchip.
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

drivers/phy/rockchip/Kconfig

@@ -15,6 +15,14 @@ config PHY_ROCKCHIP_EMMC
 	help
 	  Enable this to support the Rockchip EMMC PHY.
 
+config PHY_ROCKCHIP_INNO_HDMI
+	tristate "Rockchip INNO HDMI PHY Driver"
+	depends on (ARCH_ROCKCHIP || COMPILE_TEST) && OF
+	depends on COMMON_CLK
+	select GENERIC_PHY
+	help
+	  Enable this to support the Rockchip Innosilicon HDMI PHY.
+
 config PHY_ROCKCHIP_INNO_USB2
 	tristate "Rockchip INNO USB2PHY Driver"
 	depends on (ARCH_ROCKCHIP || COMPILE_TEST) && OF

drivers/phy/rockchip/Makefile

 # SPDX-License-Identifier: GPL-2.0
 obj-$(CONFIG_PHY_ROCKCHIP_DP)		+= phy-rockchip-dp.o
 obj-$(CONFIG_PHY_ROCKCHIP_EMMC)		+= phy-rockchip-emmc.o
+obj-$(CONFIG_PHY_ROCKCHIP_INNO_HDMI)	+= phy-rockchip-inno-hdmi.o
 obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
 obj-$(CONFIG_PHY_ROCKCHIP_PCIE)		+= phy-rockchip-pcie.o
 obj-$(CONFIG_PHY_ROCKCHIP_TYPEC)	+= phy-rockchip-typec.o

drivers/phy/rockchip/phy-rockchip-inno-hdmi.c

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2017 Rockchip Electronics Co. Ltd.
+ *
+ * Author: Zheng Yang <zhengyang@rock-chips.com>
+ *         Heiko Stuebner <heiko@sntech.de>
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/phy/phy.h>
+#include <linux/slab.h>
+
+#define UPDATE(x, h, l)		(((x) << (l)) & GENMASK((h), (l)))
+
+/* REG: 0x00 */
+#define RK3228_PRE_PLL_REFCLK_SEL_PCLK			BIT(0)
+/* REG: 0x01 */
+#define RK3228_BYPASS_RXSENSE_EN			BIT(2)
+#define RK3228_BYPASS_PWRON_EN				BIT(1)
+#define RK3228_BYPASS_PLLPD_EN				BIT(0)
+/* REG: 0x02 */
+#define RK3228_BYPASS_PDATA_EN				BIT(4)
+#define RK3228_PDATAEN_DISABLE				BIT(0)
+/* REG: 0x03 */
+#define RK3228_BYPASS_AUTO_TERM_RES_CAL			BIT(7)
+#define RK3228_AUTO_TERM_RES_CAL_SPEED_14_8(x)		UPDATE(x, 6, 0)
+/* REG: 0x04 */
+#define RK3228_AUTO_TERM_RES_CAL_SPEED_7_0(x)		UPDATE(x, 7, 0)
+/* REG: 0xaa */
+#define RK3228_POST_PLL_CTRL_MANUAL			BIT(0)
+/* REG: 0xe0 */
+#define RK3228_POST_PLL_POWER_DOWN			BIT(5)
+#define RK3228_PRE_PLL_POWER_DOWN			BIT(4)
+#define RK3228_RXSENSE_CLK_CH_ENABLE			BIT(3)
+#define RK3228_RXSENSE_DATA_CH2_ENABLE			BIT(2)
+#define RK3228_RXSENSE_DATA_CH1_ENABLE			BIT(1)
+#define RK3228_RXSENSE_DATA_CH0_ENABLE			BIT(0)
+/* REG: 0xe1 */
+#define RK3228_BANDGAP_ENABLE				BIT(4)
+#define RK3228_TMDS_DRIVER_ENABLE			GENMASK(3, 0)
+/* REG: 0xe2 */
+#define RK3228_PRE_PLL_FB_DIV_8_MASK			BIT(7)
+#define RK3228_PRE_PLL_FB_DIV_8(x)			UPDATE((x) >> 8, 7, 7)
+#define RK3228_PCLK_VCO_DIV_5_MASK			BIT(5)
+#define RK3228_PCLK_VCO_DIV_5(x)			UPDATE(x, 5, 5)
+#define RK3228_PRE_PLL_PRE_DIV_MASK			GENMASK(4, 0)
+#define RK3228_PRE_PLL_PRE_DIV(x)			UPDATE(x, 4, 0)
+/* REG: 0xe3 */
+#define RK3228_PRE_PLL_FB_DIV_7_0(x)			UPDATE(x, 7, 0)
+/* REG: 0xe4 */
+#define RK3228_PRE_PLL_PCLK_DIV_B_MASK			GENMASK(6, 5)
+#define RK3228_PRE_PLL_PCLK_DIV_B_SHIFT			5
+#define RK3228_PRE_PLL_PCLK_DIV_B(x)			UPDATE(x, 6, 5)
+#define RK3228_PRE_PLL_PCLK_DIV_A_MASK			GENMASK(4, 0)
+#define RK3228_PRE_PLL_PCLK_DIV_A(x)			UPDATE(x, 4, 0)
+/* REG: 0xe5 */
+#define RK3228_PRE_PLL_PCLK_DIV_C_MASK			GENMASK(6, 5)
+#define RK3228_PRE_PLL_PCLK_DIV_C(x)			UPDATE(x, 6, 5)
+#define RK3228_PRE_PLL_PCLK_DIV_D_MASK			GENMASK(4, 0)
+#define RK3228_PRE_PLL_PCLK_DIV_D(x)			UPDATE(x, 4, 0)
+/* REG: 0xe6 */
+#define RK3228_PRE_PLL_TMDSCLK_DIV_C_MASK		GENMASK(5, 4)
+#define RK3228_PRE_PLL_TMDSCLK_DIV_C(x)			UPDATE(x, 5, 4)
+#define RK3228_PRE_PLL_TMDSCLK_DIV_A_MASK		GENMASK(3, 2)
+#define RK3228_PRE_PLL_TMDSCLK_DIV_A(x)			UPDATE(x, 3, 2)
+#define RK3228_PRE_PLL_TMDSCLK_DIV_B_MASK		GENMASK(1, 0)
+#define RK3228_PRE_PLL_TMDSCLK_DIV_B(x)			UPDATE(x, 1, 0)
+/* REG: 0xe8 */
+#define RK3228_PRE_PLL_LOCK_STATUS			BIT(0)
+/* REG: 0xe9 */
+#define RK3228_POST_PLL_POST_DIV_ENABLE			UPDATE(3, 7, 6)
+#define RK3228_POST_PLL_PRE_DIV_MASK			GENMASK(4, 0)
+#define RK3228_POST_PLL_PRE_DIV(x)			UPDATE(x, 4, 0)
+/* REG: 0xea */
+#define RK3228_POST_PLL_FB_DIV_7_0(x)			UPDATE(x, 7, 0)
+/* REG: 0xeb */
+#define RK3228_POST_PLL_FB_DIV_8_MASK			BIT(7)
+#define RK3228_POST_PLL_FB_DIV_8(x)			UPDATE((x) >> 8, 7, 7)
+#define RK3228_POST_PLL_POST_DIV_MASK			GENMASK(5, 4)
+#define RK3228_POST_PLL_POST_DIV(x)			UPDATE(x, 5, 4)
+#define RK3228_POST_PLL_LOCK_STATUS			BIT(0)
+/* REG: 0xee */
+#define RK3228_TMDS_CH_TA_ENABLE			GENMASK(7, 4)
+/* REG: 0xef */
+#define RK3228_TMDS_CLK_CH_TA(x)			UPDATE(x, 7, 6)
+#define RK3228_TMDS_DATA_CH2_TA(x)			UPDATE(x, 5, 4)
+#define RK3228_TMDS_DATA_CH1_TA(x)			UPDATE(x, 3, 2)
+#define RK3228_TMDS_DATA_CH0_TA(x)			UPDATE(x, 1, 0)
+/* REG: 0xf0 */
+#define RK3228_TMDS_DATA_CH2_PRE_EMPHASIS_MASK		GENMASK(5, 4)
+#define RK3228_TMDS_DATA_CH2_PRE_EMPHASIS(x)		UPDATE(x, 5, 4)
+#define RK3228_TMDS_DATA_CH1_PRE_EMPHASIS_MASK		GENMASK(3, 2)
+#define RK3228_TMDS_DATA_CH1_PRE_EMPHASIS(x)		UPDATE(x, 3, 2)
+#define RK3228_TMDS_DATA_CH0_PRE_EMPHASIS_MASK		GENMASK(1, 0)
+#define RK3228_TMDS_DATA_CH0_PRE_EMPHASIS(x)		UPDATE(x, 1, 0)
+/* REG: 0xf1 */
+#define RK3228_TMDS_CLK_CH_OUTPUT_SWING(x)		UPDATE(x, 7, 4)
+#define RK3228_TMDS_DATA_CH2_OUTPUT_SWING(x)		UPDATE(x, 3, 0)
+/* REG: 0xf2 */
+#define RK3228_TMDS_DATA_CH1_OUTPUT_SWING(x)		UPDATE(x, 7, 4)
+#define RK3228_TMDS_DATA_CH0_OUTPUT_SWING(x)		UPDATE(x, 3, 0)
+
+/* REG: 0x01 */
+#define RK3328_BYPASS_RXSENSE_EN			BIT(2)
+#define RK3328_BYPASS_POWERON_EN			BIT(1)
+#define RK3328_BYPASS_PLLPD_EN				BIT(0)
+/* REG: 0x02 */
+#define RK3328_INT_POL_HIGH				BIT(7)
+#define RK3328_BYPASS_PDATA_EN				BIT(4)
+#define RK3328_PDATA_EN					BIT(0)
+/* REG:0x05 */
+#define RK3328_INT_TMDS_CLK(x)				UPDATE(x, 7, 4)
+#define RK3328_INT_TMDS_D2(x)				UPDATE(x, 3, 0)
+/* REG:0x07 */
+#define RK3328_INT_TMDS_D1(x)				UPDATE(x, 7, 4)
+#define RK3328_INT_TMDS_D0(x)				UPDATE(x, 3, 0)
+/* for all RK3328_INT_TMDS_*, ESD_DET as defined in 0xc8-0xcb */
+#define RK3328_INT_AGND_LOW_PULSE_LOCKED		BIT(3)
+#define RK3328_INT_RXSENSE_LOW_PULSE_LOCKED		BIT(2)
+#define RK3328_INT_VSS_AGND_ESD_DET			BIT(1)
+#define RK3328_INT_AGND_VSS_ESD_DET			BIT(0)
+/* REG: 0xa0 */
+#define RK3328_PCLK_VCO_DIV_5_MASK			BIT(1)
+#define RK3328_PCLK_VCO_DIV_5(x)			UPDATE(x, 1, 1)
+#define RK3328_PRE_PLL_POWER_DOWN			BIT(0)
+/* REG: 0xa1 */
+#define RK3328_PRE_PLL_PRE_DIV_MASK			GENMASK(5, 0)
+#define RK3328_PRE_PLL_PRE_DIV(x)			UPDATE(x, 5, 0)
+/* REG: 0xa2 */
+/* unset means center spread */
+#define RK3328_SPREAD_SPECTRUM_MOD_DOWN			BIT(7)
+#define RK3328_SPREAD_SPECTRUM_MOD_DISABLE		BIT(6)
+#define RK3328_PRE_PLL_FRAC_DIV_DISABLE			UPDATE(3, 5, 4)
+#define RK3328_PRE_PLL_FB_DIV_11_8_MASK			GENMASK(3, 0)
+#define RK3328_PRE_PLL_FB_DIV_11_8(x)			UPDATE((x) >> 8, 3, 0)
+/* REG: 0xa3 */
+#define RK3328_PRE_PLL_FB_DIV_7_0(x)			UPDATE(x, 7, 0)
+/* REG: 0xa4*/
+#define RK3328_PRE_PLL_TMDSCLK_DIV_C_MASK		GENMASK(1, 0)
+#define RK3328_PRE_PLL_TMDSCLK_DIV_C(x)			UPDATE(x, 1, 0)
+#define RK3328_PRE_PLL_TMDSCLK_DIV_B_MASK		GENMASK(3, 2)
+#define RK3328_PRE_PLL_TMDSCLK_DIV_B(x)			UPDATE(x, 3, 2)
+#define RK3328_PRE_PLL_TMDSCLK_DIV_A_MASK		GENMASK(5, 4)
+#define RK3328_PRE_PLL_TMDSCLK_DIV_A(x)			UPDATE(x, 5, 4)
+/* REG: 0xa5 */
+#define RK3328_PRE_PLL_PCLK_DIV_B_SHIFT			5
+#define RK3328_PRE_PLL_PCLK_DIV_B_MASK			GENMASK(6, 5)
+#define RK3328_PRE_PLL_PCLK_DIV_B(x)			UPDATE(x, 6, 5)
+#define RK3328_PRE_PLL_PCLK_DIV_A_MASK			GENMASK(4, 0)
+#define RK3328_PRE_PLL_PCLK_DIV_A(x)			UPDATE(x, 4, 0)
+/* REG: 0xa6 */
+#define RK3328_PRE_PLL_PCLK_DIV_C_SHIFT			5
+#define RK3328_PRE_PLL_PCLK_DIV_C_MASK			GENMASK(6, 5)
+#define RK3328_PRE_PLL_PCLK_DIV_C(x)			UPDATE(x, 6, 5)
+#define RK3328_PRE_PLL_PCLK_DIV_D_MASK			GENMASK(4, 0)
+#define RK3328_PRE_PLL_PCLK_DIV_D(x)			UPDATE(x, 4, 0)
+/* REG: 0xa9 */
+#define RK3328_PRE_PLL_LOCK_STATUS			BIT(0)
+/* REG: 0xaa */
+#define RK3328_POST_PLL_POST_DIV_ENABLE			GENMASK(3, 2)
+#define RK3328_POST_PLL_REFCLK_SEL_TMDS			BIT(1)
+#define RK3328_POST_PLL_POWER_DOWN			BIT(0)
+/* REG:0xab */
+#define RK3328_POST_PLL_FB_DIV_8(x)			UPDATE((x) >> 8, 7, 7)
+#define RK3328_POST_PLL_PRE_DIV(x)			UPDATE(x, 4, 0)
+/* REG: 0xac */
+#define RK3328_POST_PLL_FB_DIV_7_0(x)			UPDATE(x, 7, 0)
+/* REG: 0xad */
+#define RK3328_POST_PLL_POST_DIV_MASK			GENMASK(1, 0)
+#define RK3328_POST_PLL_POST_DIV_2			0x0
+#define RK3328_POST_PLL_POST_DIV_4			0x1
+#define RK3328_POST_PLL_POST_DIV_8			0x3
+/* REG: 0xaf */
+#define RK3328_POST_PLL_LOCK_STATUS			BIT(0)
+/* REG: 0xb0 */
+#define RK3328_BANDGAP_ENABLE				BIT(2)
+/* REG: 0xb2 */
+#define RK3328_TMDS_CLK_DRIVER_EN			BIT(3)
+#define RK3328_TMDS_D2_DRIVER_EN			BIT(2)
+#define RK3328_TMDS_D1_DRIVER_EN			BIT(1)
+#define RK3328_TMDS_D0_DRIVER_EN			BIT(0)
+#define RK3328_TMDS_DRIVER_ENABLE		(RK3328_TMDS_CLK_DRIVER_EN | \
+						RK3328_TMDS_D2_DRIVER_EN | \
+						RK3328_TMDS_D1_DRIVER_EN | \
+						RK3328_TMDS_D0_DRIVER_EN)
+/* REG:0xc5 */
+#define RK3328_BYPASS_TERM_RESISTOR_CALIB		BIT(7)
+#define RK3328_TERM_RESISTOR_CALIB_SPEED_14_8(x)	UPDATE((x) >> 8, 6, 0)
+/* REG:0xc6 */
+#define RK3328_TERM_RESISTOR_CALIB_SPEED_7_0(x)		UPDATE(x, 7, 9)
+/* REG:0xc7 */
+#define RK3328_TERM_RESISTOR_50				UPDATE(0, 2, 1)
+#define RK3328_TERM_RESISTOR_62_5			UPDATE(1, 2, 1)
+#define RK3328_TERM_RESISTOR_75				UPDATE(2, 2, 1)
+#define RK3328_TERM_RESISTOR_100			UPDATE(3, 2, 1)
+/* REG 0xc8 - 0xcb */
+#define RK3328_ESD_DETECT_MASK				GENMASK(7, 6)
+#define RK3328_ESD_DETECT_340MV				(0x0 << 6)
+#define RK3328_ESD_DETECT_280MV				(0x1 << 6)
+#define RK3328_ESD_DETECT_260MV				(0x2 << 6)
+#define RK3328_ESD_DETECT_240MV				(0x3 << 6)
+/* resistors can be used in parallel */
+#define RK3328_TMDS_TERM_RESIST_MASK			GENMASK(5, 0)
+#define RK3328_TMDS_TERM_RESIST_75			BIT(5)
+#define RK3328_TMDS_TERM_RESIST_150			BIT(4)
+#define RK3328_TMDS_TERM_RESIST_300			BIT(3)
+#define RK3328_TMDS_TERM_RESIST_600			BIT(2)
+#define RK3328_TMDS_TERM_RESIST_1000			BIT(1)
+#define RK3328_TMDS_TERM_RESIST_2000			BIT(0)
+/* REG: 0xd1 */
+#define RK3328_PRE_PLL_FRAC_DIV_23_16(x)		UPDATE((x) >> 16, 7, 0)
+/* REG: 0xd2 */
+#define RK3328_PRE_PLL_FRAC_DIV_15_8(x)			UPDATE((x) >> 8, 7, 0)
+/* REG: 0xd3 */
+#define RK3328_PRE_PLL_FRAC_DIV_7_0(x)			UPDATE(x, 7, 0)
+
+struct inno_hdmi_phy_drv_data;
+
+struct inno_hdmi_phy {
+	struct device *dev;
+	struct regmap *regmap;
+	int irq;
+
+	struct phy *phy;
+	struct clk *sysclk;
+	struct clk *refoclk;
+	struct clk *refpclk;
+
+	/* platform data */
+	const struct inno_hdmi_phy_drv_data *plat_data;
+	int chip_version;
+
+	/* clk provider */
+	struct clk_hw hw;
+	struct clk *phyclk;
+	unsigned long pixclock;
+};
+
+struct pre_pll_config {
+	unsigned long pixclock;
+	unsigned long tmdsclock;
+	u8 prediv;
+	u16 fbdiv;
+	u8 tmds_div_a;
+	u8 tmds_div_b;
+	u8 tmds_div_c;
+	u8 pclk_div_a;
+	u8 pclk_div_b;
+	u8 pclk_div_c;
+	u8 pclk_div_d;
+	u8 vco_div_5_en;
+	u32 fracdiv;
+};
+
+struct post_pll_config {
+	unsigned long tmdsclock;
+	u8 prediv;
+	u16 fbdiv;
+	u8 postdiv;
+	u8 version;
+};
+
+struct phy_config {
+	unsigned long	tmdsclock;
+	u8		regs[14];
+};
+
+struct inno_hdmi_phy_ops {
+	int (*init)(struct inno_hdmi_phy *inno);
+	int (*power_on)(struct inno_hdmi_phy *inno,
+			const struct post_pll_config *cfg,
+			const struct phy_config *phy_cfg);
+	void (*power_off)(struct inno_hdmi_phy *inno);
+};
+
+struct inno_hdmi_phy_drv_data {
+	const struct inno_hdmi_phy_ops	*ops;
+	const struct clk_ops		*clk_ops;
+	const struct phy_config		*phy_cfg_table;
+};
+
+static const struct pre_pll_config pre_pll_cfg_table[] = {
+	{ 27000000,  27000000, 1,  90, 3, 2, 2, 10, 3, 3, 4, 0, 0},
+	{ 27000000,  33750000, 1,  90, 1, 3, 3, 10, 3, 3, 4, 0, 0},
+	{ 40000000,  40000000, 1,  80, 2, 2, 2, 12, 2, 2, 2, 0, 0},
+	{ 59341000,  59341000, 1,  98, 3, 1, 2,  1, 3, 3, 4, 0, 0xE6AE6B},
+	{ 59400000,  59400000, 1,  99, 3, 1, 1,  1, 3, 3, 4, 0, 0},
+	{ 59341000,  74176250, 1,  98, 0, 3, 3,  1, 3, 3, 4, 0, 0xE6AE6B},
+	{ 59400000,  74250000, 1,  99, 1, 2, 2,  1, 3, 3, 4, 0, 0},
+	{ 74176000,  74176000, 1,  98, 1, 2, 2,  1, 2, 3, 4, 0, 0xE6AE6B},
+	{ 74250000,  74250000, 1,  99, 1, 2, 2,  1, 2, 3, 4, 0, 0},
+	{ 74176000,  92720000, 4, 494, 1, 2, 2,  1, 3, 3, 4, 0, 0x816817},
+	{ 74250000,  92812500, 4, 495, 1, 2, 2,  1, 3, 3, 4, 0, 0},
+	{148352000, 148352000, 1,  98, 1, 1, 1,  1, 2, 2, 2, 0, 0xE6AE6B},
+	{148500000, 148500000, 1,  99, 1, 1, 1,  1, 2, 2, 2, 0, 0},
+	{148352000, 185440000, 4, 494, 0, 2, 2,  1, 3, 2, 2, 0, 0x816817},
+	{148500000, 185625000, 4, 495, 0, 2, 2,  1, 3, 2, 2, 0, 0},
+	{296703000, 296703000, 1,  98, 0, 1, 1,  1, 0, 2, 2, 0, 0xE6AE6B},
+	{297000000, 297000000, 1,  99, 0, 1, 1,  1, 0, 2, 2, 0, 0},
+	{296703000, 370878750, 4, 494, 1, 2, 0,  1, 3, 1, 1, 0, 0x816817},
+	{297000000, 371250000, 4, 495, 1, 2, 0,  1, 3, 1, 1, 0, 0},
+	{593407000, 296703500, 1,  98, 0, 1, 1,  1, 0, 2, 1, 0, 0xE6AE6B},
+	{594000000, 297000000, 1,  99, 0, 1, 1,  1, 0, 2, 1, 0, 0},
+	{593407000, 370879375, 4, 494, 1, 2, 0,  1, 3, 1, 1, 1, 0x816817},
+	{594000000, 371250000, 4, 495, 1, 2, 0,  1, 3, 1, 1, 1, 0},
+	{593407000, 593407000, 1,  98, 0, 2, 0,  1, 0, 1, 1, 0, 0xE6AE6B},
+	{594000000, 594000000, 1,  99, 0, 2, 0,  1, 0, 1, 1, 0, 0},
+	{ /* sentinel */ }
+};
+
+static const struct post_pll_config post_pll_cfg_table[] = {
+	{33750000,  1, 40, 8, 1},
+	{33750000,  1, 80, 8, 2},
+	{74250000,  1, 40, 8, 1},
+	{74250000, 18, 80, 8, 2},
+	{148500000, 2, 40, 4, 3},
+	{297000000, 4, 40, 2, 3},
+	{594000000, 8, 40, 1, 3},
+	{ /* sentinel */ }
+};
+
+/* phy tuning values for an undocumented set of registers */
+static const struct phy_config rk3228_phy_cfg[] = {
+	{	165000000, {
+			0xaa, 0x00, 0x44, 0x44, 0x00, 0x00, 0x00, 0x00, 0x00,
+			0x00, 0x00, 0x00, 0x00, 0x00,
+		},
+	}, {
+		340000000, {
+			0xaa, 0x15, 0x6a, 0xaa, 0x00, 0x00, 0x00, 0x00, 0x00,
+			0x00, 0x00, 0x00, 0x00, 0x00,
+		},
+	}, {
+		594000000, {
+			0xaa, 0x15, 0x7a, 0xaa, 0x00, 0x00, 0x00, 0x00, 0x00,
+			0x00, 0x00, 0x00, 0x00, 0x00,
+		},
+	}, { /* sentinel */ },
+};
+
+/* phy tuning values for an undocumented set of registers */
+static const struct phy_config rk3328_phy_cfg[] = {
+	{	165000000, {
+			0x07, 0x0a, 0x0a, 0x0a, 0x00, 0x00, 0x08, 0x08, 0x08,
+			0x00, 0xac, 0xcc, 0xcc, 0xcc,
+		},
+	}, {
+		340000000, {
+			0x0b, 0x0d, 0x0d, 0x0d, 0x07, 0x15, 0x08, 0x08, 0x08,
+			0x3f, 0xac, 0xcc, 0xcd, 0xdd,
+		},
+	}, {
+		594000000, {
+			0x10, 0x1a, 0x1a, 0x1a, 0x07, 0x15, 0x08, 0x08, 0x08,
+			0x00, 0xac, 0xcc, 0xcc, 0xcc,
+		},
+	}, { /* sentinel */ },
+};
+
+static inline struct inno_hdmi_phy *to_inno_hdmi_phy(struct clk_hw *hw)
+{
+	return container_of(hw, struct inno_hdmi_phy, hw);
+}
+
+/*
+ * The register description of the IP block does not use any distinct names
+ * but instead the databook simply numbers the registers in one-increments.
+ * As the registers are obviously 32bit sized, the inno_* functions
+ * translate the databook register names to the actual registers addresses.
+ */
+static inline void inno_write(struct inno_hdmi_phy *inno, u32 reg, u8 val)
+{
+	regmap_write(inno->regmap, reg * 4, val);
+}
+
+static inline u8 inno_read(struct inno_hdmi_phy *inno, u32 reg)
+{
+	u32 val;
+
+	regmap_read(inno->regmap, reg * 4, &val);
+
+	return val;
+}
+
+static inline void inno_update_bits(struct inno_hdmi_phy *inno, u8 reg,
+				    u8 mask, u8 val)
+{
+	regmap_update_bits(inno->regmap, reg * 4, mask, val);
+}
+
+#define inno_poll(inno, reg, val, cond, sleep_us, timeout_us) \
+	regmap_read_poll_timeout((inno)->regmap, (reg) * 4, val, cond, \
+				 sleep_us, timeout_us)
+
+static unsigned long inno_hdmi_phy_get_tmdsclk(struct inno_hdmi_phy *inno,
+					       unsigned long rate)
+{
+	int bus_width = phy_get_bus_width(inno->phy);
+
+	switch (bus_width) {
+	case 4:
+	case 5:
+	case 6:
+	case 10:
+	case 12:
+	case 16:
+		return (u64)rate * bus_width / 8;
+	default:
+		return rate;
+	}
+}
+
+static irqreturn_t inno_hdmi_phy_rk3328_hardirq(int irq, void *dev_id)
+{
+	struct inno_hdmi_phy *inno = dev_id;
+	int intr_stat1, intr_stat2, intr_stat3;
+
+	intr_stat1 = inno_read(inno, 0x04);
+	intr_stat2 = inno_read(inno, 0x06);
+	intr_stat3 = inno_read(inno, 0x08);
+
+	if (intr_stat1)
+		inno_write(inno, 0x04, intr_stat1);
+	if (intr_stat2)
+		inno_write(inno, 0x06, intr_stat2);
+	if (intr_stat3)
+		inno_write(inno, 0x08, intr_stat3);
+
+	if (intr_stat1 || intr_stat2 || intr_stat3)
+		return IRQ_WAKE_THREAD;
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t inno_hdmi_phy_rk3328_irq(int irq, void *dev_id)
+{
+	struct inno_hdmi_phy *inno = dev_id;
+
+	inno_update_bits(inno, 0x02, RK3328_PDATA_EN, 0);
+	usleep_range(10, 20);
+	inno_update_bits(inno, 0x02, RK3328_PDATA_EN, RK3328_PDATA_EN);
+
+	return IRQ_HANDLED;
+}
+
+static int inno_hdmi_phy_power_on(struct phy *phy)
+{
+	struct inno_hdmi_phy *inno = phy_get_drvdata(phy);
+	const struct post_pll_config *cfg = post_pll_cfg_table;
+	const struct phy_config *phy_cfg = inno->plat_data->phy_cfg_table;
+	unsigned long tmdsclock = inno_hdmi_phy_get_tmdsclk(inno,
+							    inno->pixclock);
+	int ret;
+
+	if (!tmdsclock) {
+		dev_err(inno->dev, "TMDS clock is zero!\n");
+		return -EINVAL;
+	}
+
+	if (!inno->plat_data->ops->power_on)
+		return -EINVAL;
+
+	for (; cfg->tmdsclock != 0; cfg++)
+		if (tmdsclock <= cfg->tmdsclock &&
+		    cfg->version & inno->chip_version)
+			break;
+
+	for (; phy_cfg->tmdsclock != 0; phy_cfg++)
+		if (tmdsclock <= phy_cfg->tmdsclock)
+			break;
+
+	if (cfg->tmdsclock == 0 || phy_cfg->tmdsclock == 0)
+		return -EINVAL;
+
+	dev_dbg(inno->dev, "Inno HDMI PHY Power On\n");
+
+	ret = clk_prepare_enable(inno->phyclk);
+	if (ret)
+		return ret;
+
+	ret = inno->plat_data->ops->power_on(inno, cfg, phy_cfg);
+	if (ret) {
+		clk_disable_unprepare(inno->phyclk);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int inno_hdmi_phy_power_off(struct phy *phy)
+{
+	struct inno_hdmi_phy *inno = phy_get_drvdata(phy);
+
+	if (!inno->plat_data->ops->power_off)
+		return -EINVAL;
+
+	inno->plat_data->ops->power_off(inno);
+
+	clk_disable_unprepare(inno->phyclk);
+
+	dev_dbg(inno->dev, "Inno HDMI PHY Power Off\n");
+
+	return 0;
+}
+
+static const struct phy_ops inno_hdmi_phy_ops = {
+	.owner = THIS_MODULE,
+	.power_on = inno_hdmi_phy_power_on,
+	.power_off = inno_hdmi_phy_power_off,
+};
+
+static const
+struct pre_pll_config *inno_hdmi_phy_get_pre_pll_cfg(struct inno_hdmi_phy *inno,
+						     unsigned long rate)
+{
+	const struct pre_pll_config *cfg = pre_pll_cfg_table;
+	unsigned long tmdsclock = inno_hdmi_phy_get_tmdsclk(inno, rate);
+
+	for (; cfg->pixclock != 0; cfg++)
+		if (cfg->pixclock == rate && cfg->tmdsclock == tmdsclock)
+			break;
+
+	if (cfg->pixclock == 0)
+		return ERR_PTR(-EINVAL);
+
+	return cfg;
+}
+
+static int inno_hdmi_phy_rk3228_clk_is_prepared(struct clk_hw *hw)
+{
+	struct inno_hdmi_phy *inno = to_inno_hdmi_phy(hw);
+	u8 status;
+
+	status = inno_read(inno, 0xe0) & RK3228_PRE_PLL_POWER_DOWN;
+	return status ? 0 : 1;
+}
+
+static int inno_hdmi_phy_rk3228_clk_prepare(struct clk_hw *hw)
+{
+	struct inno_hdmi_phy *inno = to_inno_hdmi_phy(hw);
+
+	inno_update_bits(inno, 0xe0, RK3228_PRE_PLL_POWER_DOWN, 0);
+	return 0;
+}
+
+static void inno_hdmi_phy_rk3228_clk_unprepare(struct clk_hw *hw)
+{
+	struct inno_hdmi_phy *inno = to_inno_hdmi_phy(hw);
+
+	inno_update_bits(inno, 0xe0, RK3228_PRE_PLL_POWER_DOWN,
+			 RK3228_PRE_PLL_POWER_DOWN);
+}
+
+static
+unsigned long inno_hdmi_phy_rk3228_clk_recalc_rate(struct clk_hw *hw,
+						   unsigned long parent_rate)
+{
+	struct inno_hdmi_phy *inno = to_inno_hdmi_phy(hw);
+	u8 nd, no_a, no_b, no_d;
+	u64 vco;
+	u16 nf;
+
+	nd = inno_read(inno, 0xe2) & RK3228_PRE_PLL_PRE_DIV_MASK;
+	nf = (inno_read(inno, 0xe2) & RK3228_PRE_PLL_FB_DIV_8_MASK) << 1;
+	nf |= inno_read(inno, 0xe3);
+	vco = parent_rate * nf;
+
+	if (inno_read(inno, 0xe2) & RK3228_PCLK_VCO_DIV_5_MASK) {
+		do_div(vco, nd * 5);
+	} else {
+		no_a = inno_read(inno, 0xe4) & RK3228_PRE_PLL_PCLK_DIV_A_MASK;
+		if (!no_a)
+			no_a = 1;
+		no_b = inno_read(inno, 0xe4) & RK3228_PRE_PLL_PCLK_DIV_B_MASK;
+		no_b >>= RK3228_PRE_PLL_PCLK_DIV_B_SHIFT;
+		no_b += 2;
+		no_d = inno_read(inno, 0xe5) & RK3228_PRE_PLL_PCLK_DIV_D_MASK;
+
+		do_div(vco, (nd * (no_a == 1 ? no_b : no_a) * no_d * 2));
+	}
+
+	inno->pixclock = vco;
+
+	dev_dbg(inno->dev, "%s rate %lu\n", __func__, inno->pixclock);
+
+	return vco;
+}
+
+static long inno_hdmi_phy_rk3228_clk_round_rate(struct clk_hw *hw,
+						unsigned long rate,
+						unsigned long *parent_rate)
+{
+	const struct pre_pll_config *cfg = pre_pll_cfg_table;
+
+	for (; cfg->pixclock != 0; cfg++)
+		if (cfg->pixclock == rate && !cfg->fracdiv)
+			break;
+
+	if (cfg->pixclock == 0)
+		return -EINVAL;
+
+	return cfg->pixclock;
+}
+
+static int inno_hdmi_phy_rk3228_clk_set_rate(struct clk_hw *hw,
+					     unsigned long rate,
+					     unsigned long parent_rate)
+{
+	struct inno_hdmi_phy *inno = to_inno_hdmi_phy(hw);
+	const struct pre_pll_config *cfg = pre_pll_cfg_table;
+	unsigned long tmdsclock = inno_hdmi_phy_get_tmdsclk(inno, rate);
+	u32 v;
+	int ret;
+
+	dev_dbg(inno->dev, "%s rate %lu tmdsclk %lu\n",
+		__func__, rate, tmdsclock);
+
+	cfg = inno_hdmi_phy_get_pre_pll_cfg(inno, rate);
+	if (IS_ERR(cfg))
+		return PTR_ERR(cfg);
+
+	/* Power down PRE-PLL */
+	inno_update_bits(inno, 0xe0, RK3228_PRE_PLL_POWER_DOWN,
+			 RK3228_PRE_PLL_POWER_DOWN);
+
+	inno_update_bits(inno, 0xe2, RK3228_PRE_PLL_FB_DIV_8_MASK |
+			 RK3228_PCLK_VCO_DIV_5_MASK |
+			 RK3228_PRE_PLL_PRE_DIV_MASK,
+			 RK3228_PRE_PLL_FB_DIV_8(cfg->fbdiv) |
+			 RK3228_PCLK_VCO_DIV_5(cfg->vco_div_5_en) |
+			 RK3228_PRE_PLL_PRE_DIV(cfg->prediv));
+	inno_write(inno, 0xe3, RK3228_PRE_PLL_FB_DIV_7_0(cfg->fbdiv));
+	inno_update_bits(inno, 0xe4, RK3228_PRE_PLL_PCLK_DIV_B_MASK |
+			 RK3228_PRE_PLL_PCLK_DIV_A_MASK,
+			 RK3228_PRE_PLL_PCLK_DIV_B(cfg->pclk_div_b) |
+			 RK3228_PRE_PLL_PCLK_DIV_A(cfg->pclk_div_a));
+	inno_update_bits(inno, 0xe5, RK3228_PRE_PLL_PCLK_DIV_C_MASK |
+			 RK3228_PRE_PLL_PCLK_DIV_D_MASK,
+			 RK3228_PRE_PLL_PCLK_DIV_C(cfg->pclk_div_c) |
+			 RK3228_PRE_PLL_PCLK_DIV_D(cfg->pclk_div_d));
+	inno_update_bits(inno, 0xe6, RK3228_PRE_PLL_TMDSCLK_DIV_C_MASK |
+			 RK3228_PRE_PLL_TMDSCLK_DIV_A_MASK |
+			 RK3228_PRE_PLL_TMDSCLK_DIV_B_MASK,
+			 RK3228_PRE_PLL_TMDSCLK_DIV_C(cfg->tmds_div_c) |
+			 RK3228_PRE_PLL_TMDSCLK_DIV_A(cfg->tmds_div_a) |
+			 RK3228_PRE_PLL_TMDSCLK_DIV_B(cfg->tmds_div_b));
+
+	/* Power up PRE-PLL */
+	inno_update_bits(inno, 0xe0, RK3228_PRE_PLL_POWER_DOWN, 0);
+
+	/* Wait for Pre-PLL lock */
+	ret = inno_poll(inno, 0xe8, v, v & RK3228_PRE_PLL_LOCK_STATUS,
+			100, 100000);
+	if (ret) {
+		dev_err(inno->dev, "Pre-PLL locking failed\n");
+		return ret;
+	}
+
+	inno->pixclock = rate;
+
+	return 0;
+}
+
+static const struct clk_ops inno_hdmi_phy_rk3228_clk_ops = {
+	.prepare = inno_hdmi_phy_rk3228_clk_prepare,
+	.unprepare = inno_hdmi_phy_rk3228_clk_unprepare,
+	.is_prepared = inno_hdmi_phy_rk3228_clk_is_prepared,
+	.recalc_rate = inno_hdmi_phy_rk3228_clk_recalc_rate,
+	.round_rate = inno_hdmi_phy_rk3228_clk_round_rate,
+	.set_rate = inno_hdmi_phy_rk3228_clk_set_rate,
+};
+
+static int inno_hdmi_phy_rk3328_clk_is_prepared(struct clk_hw *hw)
+{
+	struct inno_hdmi_phy *inno = to_inno_hdmi_phy(hw);
+	u8 status;
+
+	status = inno_read(inno, 0xa0) & RK3328_PRE_PLL_POWER_DOWN;
+	return status ? 0 : 1;
+}
+
+static int inno_hdmi_phy_rk3328_clk_prepare(struct clk_hw *hw)
+{
+	struct inno_hdmi_phy *inno = to_inno_hdmi_phy(hw);
+
+	inno_update_bits(inno, 0xa0, RK3328_PRE_PLL_POWER_DOWN, 0);
+	return 0;
+}
+
+static void inno_hdmi_phy_rk3328_clk_unprepare(struct clk_hw *hw)
+{
+	struct inno_hdmi_phy *inno = to_inno_hdmi_phy(hw);
+
+	inno_update_bits(inno, 0xa0, RK3328_PRE_PLL_POWER_DOWN,
+			 RK3328_PRE_PLL_POWER_DOWN);
+}
+
+static
+unsigned long inno_hdmi_phy_rk3328_clk_recalc_rate(struct clk_hw *hw,
+						   unsigned long parent_rate)
+{
+	struct inno_hdmi_phy *inno = to_inno_hdmi_phy(hw);
+	unsigned long frac;
+	u8 nd, no_a, no_b, no_c, no_d;
+	u64 vco;
+	u16 nf;
+
+	nd = inno_read(inno, 0xa1) & RK3328_PRE_PLL_PRE_DIV_MASK;
+	nf = ((inno_read(inno, 0xa2) & RK3328_PRE_PLL_FB_DIV_11_8_MASK) << 8);
+	nf |= inno_read(inno, 0xa3);
+	vco = parent_rate * nf;
+
+	if (!(inno_read(inno, 0xa2) & RK3328_PRE_PLL_FRAC_DIV_DISABLE)) {
+		frac = inno_read(inno, 0xd3) |
+		       (inno_read(inno, 0xd2) << 8) |
+		       (inno_read(inno, 0xd1) << 16);
+		vco += DIV_ROUND_CLOSEST(parent_rate * frac, (1 << 24));
+	}
+
+	if (inno_read(inno, 0xa0) & RK3328_PCLK_VCO_DIV_5_MASK) {
+		do_div(vco, nd * 5);
+	} else {
+		no_a = inno_read(inno, 0xa5) & RK3328_PRE_PLL_PCLK_DIV_A_MASK;
+		no_b = inno_read(inno, 0xa5) & RK3328_PRE_PLL_PCLK_DIV_B_MASK;
+		no_b >>= RK3328_PRE_PLL_PCLK_DIV_B_SHIFT;
+		no_b += 2;
+		no_c = inno_read(inno, 0xa6) & RK3328_PRE_PLL_PCLK_DIV_C_MASK;
+		no_c >>= RK3328_PRE_PLL_PCLK_DIV_C_SHIFT;
+		no_c = 1 << no_c;
+		no_d = inno_read(inno, 0xa6) & RK3328_PRE_PLL_PCLK_DIV_D_MASK;
+
+		do_div(vco, (nd * (no_a == 1 ? no_b : no_a) * no_d * 2));
+	}
+
+	inno->pixclock = vco;
+	dev_dbg(inno->dev, "%s rate %lu\n", __func__, inno->pixclock);
+
+	return vco;
+}
+
+static long inno_hdmi_phy_rk3328_clk_round_rate(struct clk_hw *hw,
+						unsigned long rate,
+						unsigned long *parent_rate)
+{
+	const struct pre_pll_config *cfg = pre_pll_cfg_table;
+
+	for (; cfg->pixclock != 0; cfg++)
+		if (cfg->pixclock == rate)
+			break;
+
+	if (cfg->pixclock == 0)
+		return -EINVAL;
+
+	return cfg->pixclock;
+}
+
+static int inno_hdmi_phy_rk3328_clk_set_rate(struct clk_hw *hw,
+					     unsigned long rate,
+					     unsigned long parent_rate)
+{
+	struct inno_hdmi_phy *inno = to_inno_hdmi_phy(hw);
+	const struct pre_pll_config *cfg = pre_pll_cfg_table;
+	unsigned long tmdsclock = inno_hdmi_phy_get_tmdsclk(inno, rate);
+	u32 val;
+	int ret;
+
+	dev_dbg(inno->dev, "%s rate %lu tmdsclk %lu\n",
+		__func__, rate, tmdsclock);
+
+	cfg = inno_hdmi_phy_get_pre_pll_cfg(inno, rate);
+	if (IS_ERR(cfg))
+		return PTR_ERR(cfg);
+
+	inno_update_bits(inno, 0xa0, RK3328_PRE_PLL_POWER_DOWN,
+			 RK3328_PRE_PLL_POWER_DOWN);
+
+	/* Configure pre-pll */
+	inno_update_bits(inno, 0xa0, RK3228_PCLK_VCO_DIV_5_MASK,
+			 RK3228_PCLK_VCO_DIV_5(cfg->vco_div_5_en));
+	inno_write(inno, 0xa1, RK3328_PRE_PLL_PRE_DIV(cfg->prediv));
+
+	val = RK3328_SPREAD_SPECTRUM_MOD_DISABLE;
+	if (!cfg->fracdiv)
+		val |= RK3328_PRE_PLL_FRAC_DIV_DISABLE;
+	inno_write(inno, 0xa2, RK3328_PRE_PLL_FB_DIV_11_8(cfg->fbdiv) | val);
+	inno_write(inno, 0xa3, RK3328_PRE_PLL_FB_DIV_7_0(cfg->fbdiv));
+	inno_write(inno, 0xa5, RK3328_PRE_PLL_PCLK_DIV_A(cfg->pclk_div_a) |
+		   RK3328_PRE_PLL_PCLK_DIV_B(cfg->pclk_div_b));
+	inno_write(inno, 0xa6, RK3328_PRE_PLL_PCLK_DIV_C(cfg->pclk_div_c) |
+		   RK3328_PRE_PLL_PCLK_DIV_D(cfg->pclk_div_d));
+	inno_write(inno, 0xa4, RK3328_PRE_PLL_TMDSCLK_DIV_C(cfg->tmds_div_c) |
+		   RK3328_PRE_PLL_TMDSCLK_DIV_A(cfg->tmds_div_a) |
+		   RK3328_PRE_PLL_TMDSCLK_DIV_B(cfg->tmds_div_b));
+	inno_write(inno, 0xd3, RK3328_PRE_PLL_FRAC_DIV_7_0(cfg->fracdiv));
+	inno_write(inno, 0xd2, RK3328_PRE_PLL_FRAC_DIV_15_8(cfg->fracdiv));
+	inno_write(inno, 0xd1, RK3328_PRE_PLL_FRAC_DIV_23_16(cfg->fracdiv));
+
+	inno_update_bits(inno, 0xa0, RK3328_PRE_PLL_POWER_DOWN, 0);
+
+	/* Wait for Pre-PLL lock */
+	ret = inno_poll(inno, 0xa9, val, val & RK3328_PRE_PLL_LOCK_STATUS,
+			1000, 10000);
+	if (ret) {
+		dev_err(inno->dev, "Pre-PLL locking failed\n");
+		return ret;
+	}
+
+	inno->pixclock = rate;
+
+	return 0;
+}
+
+static const struct clk_ops inno_hdmi_phy_rk3328_clk_ops = {
+	.prepare = inno_hdmi_phy_rk3328_clk_prepare,
+	.unprepare = inno_hdmi_phy_rk3328_clk_unprepare,
+	.is_prepared = inno_hdmi_phy_rk3328_clk_is_prepared,
+	.recalc_rate = inno_hdmi_phy_rk3328_clk_recalc_rate,
+	.round_rate = inno_hdmi_phy_rk3328_clk_round_rate,
+	.set_rate = inno_hdmi_phy_rk3328_clk_set_rate,
+};
+
+static int inno_hdmi_phy_clk_register(struct inno_hdmi_phy *inno)
+{
+	struct device *dev = inno->dev;
+	struct device_node *np = dev->of_node;
+	struct clk_init_data init;
+	const char *parent_name;
+	int ret;
+
+	parent_name = __clk_get_name(inno->refoclk);
+
+	init.parent_names = &parent_name;
+	init.num_parents = 1;
+	init.flags = 0;
+	init.name = "pin_hd20_pclk";
+	init.ops = inno->plat_data->clk_ops;
+
+	/* optional override of the clock name */
+	of_property_read_string(np, "clock-output-names", &init.name);
+
+	inno->hw.init = &init;
+
+	inno->phyclk = devm_clk_register(dev, &inno->hw);
+	if (IS_ERR(inno->phyclk)) {
+		ret = PTR_ERR(inno->phyclk);
+		dev_err(dev, "failed to register clock: %d\n", ret);
+		return ret;
+	}
+
+	ret = of_clk_add_provider(np, of_clk_src_simple_get, inno->phyclk);
+	if (ret) {
+		dev_err(dev, "failed to register clock provider: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int inno_hdmi_phy_rk3228_init(struct inno_hdmi_phy *inno)
+{
+	/*
+	 * Use phy internal register control
+	 * rxsense/poweron/pllpd/pdataen signal.
+	 */
+	inno_write(inno, 0x01, RK3228_BYPASS_RXSENSE_EN |
+		   RK3228_BYPASS_PWRON_EN |
+		   RK3228_BYPASS_PLLPD_EN);
+	inno_update_bits(inno, 0x02, RK3228_BYPASS_PDATA_EN,
+			 RK3228_BYPASS_PDATA_EN);
+
+	/* manual power down post-PLL */
+	inno_update_bits(inno, 0xaa, RK3228_POST_PLL_CTRL_MANUAL,
+			 RK3228_POST_PLL_CTRL_MANUAL);
+
+	inno->chip_version = 1;
+
+	return 0;
+}
+
+static int
+inno_hdmi_phy_rk3228_power_on(struct inno_hdmi_phy *inno,
+			      const struct post_pll_config *cfg,
+			      const struct phy_config *phy_cfg)
+{
+	int ret;
+	u32 v;
+
+	inno_update_bits(inno, 0x02, RK3228_PDATAEN_DISABLE,
+			 RK3228_PDATAEN_DISABLE);
+	inno_update_bits(inno, 0xe0, RK3228_PRE_PLL_POWER_DOWN |
+			 RK3228_POST_PLL_POWER_DOWN,
+			 RK3228_PRE_PLL_POWER_DOWN |
+			 RK3228_POST_PLL_POWER_DOWN);
+
+	/* Post-PLL update */
+	inno_update_bits(inno, 0xe9, RK3228_POST_PLL_PRE_DIV_MASK,
+			 RK3228_POST_PLL_PRE_DIV(cfg->prediv));
+	inno_update_bits(inno, 0xeb, RK3228_POST_PLL_FB_DIV_8_MASK,
+			 RK3228_POST_PLL_FB_DIV_8(cfg->fbdiv));
+	inno_write(inno, 0xea, RK3228_POST_PLL_FB_DIV_7_0(cfg->fbdiv));
+
+	if (cfg->postdiv == 1) {
+		inno_update_bits(inno, 0xe9, RK3228_POST_PLL_POST_DIV_ENABLE,
+				 0);
+	} else {
+		int div = cfg->postdiv / 2 - 1;
+
+		inno_update_bits(inno, 0xe9, RK3228_POST_PLL_POST_DIV_ENABLE,
+				 RK3228_POST_PLL_POST_DIV_ENABLE);
+		inno_update_bits(inno, 0xeb, RK3228_POST_PLL_POST_DIV_MASK,
+				 RK3228_POST_PLL_POST_DIV(div));
+	}
+
+	for (v = 0; v < 4; v++)
+		inno_write(inno, 0xef + v, phy_cfg->regs[v]);
+
+	inno_update_bits(inno, 0xe0, RK3228_PRE_PLL_POWER_DOWN |
+			 RK3228_POST_PLL_POWER_DOWN, 0);
+	inno_update_bits(inno, 0xe1, RK3228_BANDGAP_ENABLE,
+			 RK3228_BANDGAP_ENABLE);
+	inno_update_bits(inno, 0xe1, RK3228_TMDS_DRIVER_ENABLE,
+			 RK3228_TMDS_DRIVER_ENABLE);
+
+	/* Wait for post PLL lock */
+	ret = inno_poll(inno, 0xeb, v, v & RK3228_POST_PLL_LOCK_STATUS,
+			100, 100000);
+	if (ret) {
+		dev_err(inno->dev, "Post-PLL locking failed\n");
+		return ret;
+	}
+
+	if (cfg->tmdsclock > 340000000)
+		msleep(100);
+
+	inno_update_bits(inno, 0x02, RK3228_PDATAEN_DISABLE, 0);
+	return 0;
+}
+
+static void inno_hdmi_phy_rk3228_power_off(struct inno_hdmi_phy *inno)
+{
+	inno_update_bits(inno, 0xe1, RK3228_TMDS_DRIVER_ENABLE, 0);
+	inno_update_bits(inno, 0xe1, RK3228_BANDGAP_ENABLE, 0);
+	inno_update_bits(inno, 0xe0, RK3228_POST_PLL_POWER_DOWN,
+			 RK3228_POST_PLL_POWER_DOWN);
+}
+
+static const struct inno_hdmi_phy_ops rk3228_hdmi_phy_ops = {
+	.init = inno_hdmi_phy_rk3228_init,
+	.power_on = inno_hdmi_phy_rk3228_power_on,
+	.power_off = inno_hdmi_phy_rk3228_power_off,
+};
+
+static int inno_hdmi_phy_rk3328_init(struct inno_hdmi_phy *inno)
+{
+	struct nvmem_cell *cell;
+	unsigned char *efuse_buf;
+	size_t len;
+
+	/*
+	 * Use phy internal register control
+	 * rxsense/poweron/pllpd/pdataen signal.
+	 */
+	inno_write(inno, 0x01, RK3328_BYPASS_RXSENSE_EN |
+		   RK3328_BYPASS_POWERON_EN |
+		   RK3328_BYPASS_PLLPD_EN);
+	inno_write(inno, 0x02, RK3328_INT_POL_HIGH | RK3328_BYPASS_PDATA_EN |
+		   RK3328_PDATA_EN);
+
+	/* Disable phy irq */
+	inno_write(inno, 0x05, 0);
+	inno_write(inno, 0x07, 0);
+
+	/* try to read the chip-version */
+	inno->chip_version = 1;
+	cell = nvmem_cell_get(inno->dev, "cpu-version");
+	if (IS_ERR(cell)) {
+		if (PTR_ERR(cell) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+
+		return 0;
+	}
+
+	efuse_buf = nvmem_cell_read(cell, &len);
+	nvmem_cell_put(cell);
+
+	if (IS_ERR(efuse_buf))
+		return 0;
+	if (len == 1)
+		inno->chip_version = efuse_buf[0] + 1;
+	kfree(efuse_buf);
+
+	return 0;
+}
+
+static int
+inno_hdmi_phy_rk3328_power_on(struct inno_hdmi_phy *inno,
+			      const struct post_pll_config *cfg,
+			      const struct phy_config *phy_cfg)
+{
+	int ret;
+	u32 v;
+
+	inno_update_bits(inno, 0x02, RK3328_PDATA_EN, 0);
+	inno_update_bits(inno, 0xaa, RK3328_POST_PLL_POWER_DOWN,
+			 RK3328_POST_PLL_POWER_DOWN);
+
+	inno_write(inno, 0xac, RK3328_POST_PLL_FB_DIV_7_0(cfg->fbdiv));
+	if (cfg->postdiv == 1) {
+		inno_write(inno, 0xaa, RK3328_POST_PLL_REFCLK_SEL_TMDS);
+		inno_write(inno, 0xab, RK3328_POST_PLL_FB_DIV_8(cfg->fbdiv) |
+			   RK3328_POST_PLL_PRE_DIV(cfg->prediv));
+	} else {
+		v = (cfg->postdiv / 2) - 1;
+		v &= RK3328_POST_PLL_POST_DIV_MASK;
+		inno_write(inno, 0xad, v);
+		inno_write(inno, 0xab, RK3328_POST_PLL_FB_DIV_8(cfg->fbdiv) |
+			   RK3328_POST_PLL_PRE_DIV(cfg->prediv));
+		inno_write(inno, 0xaa, RK3328_POST_PLL_POST_DIV_ENABLE |
+			   RK3328_POST_PLL_REFCLK_SEL_TMDS);
+	}
+
+	for (v = 0; v < 14; v++)
+		inno_write(inno, 0xb5 + v, phy_cfg->regs[v]);
+
+	/* set ESD detection threshold for TMDS CLK, D2, D1 and D0 */
+	for (v = 0; v < 4; v++)
+		inno_update_bits(inno, 0xc8 + v, RK3328_ESD_DETECT_MASK,
+				 RK3328_ESD_DETECT_340MV);
+
+	if (phy_cfg->tmdsclock > 340000000) {
+		/* Set termination resistor to 100ohm */
+		v = clk_get_rate(inno->sysclk) / 100000;
+		inno_write(inno, 0xc5, RK3328_TERM_RESISTOR_CALIB_SPEED_14_8(v)
+			   | RK3328_BYPASS_TERM_RESISTOR_CALIB);
+		inno_write(inno, 0xc6, RK3328_TERM_RESISTOR_CALIB_SPEED_7_0(v));
+		inno_write(inno, 0xc7, RK3328_TERM_RESISTOR_100);
+		inno_update_bits(inno, 0xc5,
+				 RK3328_BYPASS_TERM_RESISTOR_CALIB, 0);
+	} else {
+		inno_write(inno, 0xc5, RK3328_BYPASS_TERM_RESISTOR_CALIB);
+
+		/* clk termination resistor is 50ohm (parallel resistors) */
+		if (phy_cfg->tmdsclock > 165000000)
+			inno_update_bits(inno, 0xc8,
+					 RK3328_TMDS_TERM_RESIST_MASK,
+					 RK3328_TMDS_TERM_RESIST_75 |
+					 RK3328_TMDS_TERM_RESIST_150);
+
+		/* data termination resistor for D2, D1 and D0 is 150ohm */
+		for (v = 0; v < 3; v++)
+			inno_update_bits(inno, 0xc9 + v,
+					 RK3328_TMDS_TERM_RESIST_MASK,
+					 RK3328_TMDS_TERM_RESIST_150);
+	}
+
+	inno_update_bits(inno, 0xaa, RK3328_POST_PLL_POWER_DOWN, 0);
+	inno_update_bits(inno, 0xb0, RK3328_BANDGAP_ENABLE,
+			 RK3328_BANDGAP_ENABLE);
+	inno_update_bits(inno, 0xb2, RK3328_TMDS_DRIVER_ENABLE,
+			 RK3328_TMDS_DRIVER_ENABLE);
+
+	/* Wait for post PLL lock */
+	ret = inno_poll(inno, 0xaf, v, v & RK3328_POST_PLL_LOCK_STATUS,
+			1000, 10000);
+	if (ret) {
+		dev_err(inno->dev, "Post-PLL locking failed\n");
+		return ret;
+	}
+
+	if (phy_cfg->tmdsclock > 340000000)
+		msleep(100);
+
+	inno_update_bits(inno, 0x02, RK3328_PDATA_EN, RK3328_PDATA_EN);
+
+	/* Enable PHY IRQ */
+	inno_write(inno, 0x05, RK3328_INT_TMDS_CLK(RK3328_INT_VSS_AGND_ESD_DET)
+		   | RK3328_INT_TMDS_D2(RK3328_INT_VSS_AGND_ESD_DET));
+	inno_write(inno, 0x07, RK3328_INT_TMDS_D1(RK3328_INT_VSS_AGND_ESD_DET)
+		   | RK3328_INT_TMDS_D0(RK3328_INT_VSS_AGND_ESD_DET));
+	return 0;
+}
+
+static void inno_hdmi_phy_rk3328_power_off(struct inno_hdmi_phy *inno)
+{
+	inno_update_bits(inno, 0xb2, RK3328_TMDS_DRIVER_ENABLE, 0);
+	inno_update_bits(inno, 0xb0, RK3328_BANDGAP_ENABLE, 0);
+	inno_update_bits(inno, 0xaa, RK3328_POST_PLL_POWER_DOWN,
+			 RK3328_POST_PLL_POWER_DOWN);
+
+	/* Disable PHY IRQ */
+	inno_write(inno, 0x05, 0);
+	inno_write(inno, 0x07, 0);
+}
+
+static const struct inno_hdmi_phy_ops rk3328_hdmi_phy_ops = {
+	.init = inno_hdmi_phy_rk3328_init,
+	.power_on = inno_hdmi_phy_rk3328_power_on,
+	.power_off = inno_hdmi_phy_rk3328_power_off,
+};
+
+static const struct inno_hdmi_phy_drv_data rk3228_hdmi_phy_drv_data = {
+	.ops = &rk3228_hdmi_phy_ops,
+	.clk_ops = &inno_hdmi_phy_rk3228_clk_ops,
+	.phy_cfg_table = rk3228_phy_cfg,
+};
+
+static const struct inno_hdmi_phy_drv_data rk3328_hdmi_phy_drv_data = {
+	.ops = &rk3328_hdmi_phy_ops,
+	.clk_ops = &inno_hdmi_phy_rk3328_clk_ops,
+	.phy_cfg_table = rk3328_phy_cfg,
+};
+
+static const struct regmap_config inno_hdmi_phy_regmap_config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = 0x400,
+};
+
+static void inno_hdmi_phy_action(void *data)
+{
+	struct inno_hdmi_phy *inno = data;
+
+	clk_disable_unprepare(inno->refpclk);
+	clk_disable_unprepare(inno->sysclk);
+}
+
+static int inno_hdmi_phy_probe(struct platform_device *pdev)
+{
+	struct inno_hdmi_phy *inno;
+	struct phy_provider *phy_provider;
+	struct resource *res;
+	void __iomem *regs;
+	int ret;
+
+	inno = devm_kzalloc(&pdev->dev, sizeof(*inno), GFP_KERNEL);
+	if (!inno)
+		return -ENOMEM;
+
+	inno->dev = &pdev->dev;
+
+	inno->plat_data = of_device_get_match_data(inno->dev);
+	if (!inno->plat_data || !inno->plat_data->ops)
+		return -EINVAL;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	regs = devm_ioremap_resource(inno->dev, res);
+	if (IS_ERR(regs))
+		return PTR_ERR(regs);
+
+	inno->sysclk = devm_clk_get(inno->dev, "sysclk");
+	if (IS_ERR(inno->sysclk)) {
+		ret = PTR_ERR(inno->sysclk);
+		dev_err(inno->dev, "failed to get sysclk: %d\n", ret);
+		return ret;
+	}
+
+	inno->refpclk = devm_clk_get(inno->dev, "refpclk");
+	if (IS_ERR(inno->refpclk)) {
+		ret = PTR_ERR(inno->refpclk);
+		dev_err(inno->dev, "failed to get ref clock: %d\n", ret);
+		return ret;
+	}
+
+	inno->refoclk = devm_clk_get(inno->dev, "refoclk");
+	if (IS_ERR(inno->refoclk)) {
+		ret = PTR_ERR(inno->refoclk);
+		dev_err(inno->dev, "failed to get oscillator-ref clock: %d\n",
+			ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(inno->sysclk);
+	if (ret) {
+		dev_err(inno->dev, "Cannot enable inno phy sysclk: %d\n", ret);
+		return ret;
+	}
+
+	/*
+	 * Refpclk needs to be on, on at least the rk3328 for still
+	 * unknown reasons.
+	 */
+	ret = clk_prepare_enable(inno->refpclk);
+	if (ret) {
+		dev_err(inno->dev, "failed to enable refpclk\n");
+		clk_disable_unprepare(inno->sysclk);
+		return ret;
+	}
+
+	ret = devm_add_action_or_reset(inno->dev, inno_hdmi_phy_action,
+				       inno);
+	if (ret)
+		return ret;
+
+	inno->regmap = devm_regmap_init_mmio(inno->dev, regs,
+					     &inno_hdmi_phy_regmap_config);
+	if (IS_ERR(inno->regmap))
+		return PTR_ERR(inno->regmap);
+
+	/* only the newer rk3328 hdmiphy has an interrupt */
+	inno->irq = platform_get_irq(pdev, 0);
+	if (inno->irq > 0) {
+		ret = devm_request_threaded_irq(inno->dev, inno->irq,
+						inno_hdmi_phy_rk3328_hardirq,
+						inno_hdmi_phy_rk3328_irq,
+						IRQF_SHARED,
+						dev_name(inno->dev), inno);
+		if (ret)
+			return ret;
+	}
+
+	inno->phy = devm_phy_create(inno->dev, NULL, &inno_hdmi_phy_ops);
+	if (IS_ERR(inno->phy)) {
+		dev_err(inno->dev, "failed to create HDMI PHY\n");
+		return PTR_ERR(inno->phy);
+	}
+
+	phy_set_drvdata(inno->phy, inno);
+	phy_set_bus_width(inno->phy, 8);
+
+	if (inno->plat_data->ops->init) {
+		ret = inno->plat_data->ops->init(inno);
+		if (ret)
+			return ret;
+	}
+
+	ret = inno_hdmi_phy_clk_register(inno);
+	if (ret)
+		return ret;
+
+	phy_provider = devm_of_phy_provider_register(inno->dev,
+						     of_phy_simple_xlate);
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static int inno_hdmi_phy_remove(struct platform_device *pdev)
+{
+	of_clk_del_provider(pdev->dev.of_node);
+
+	return 0;
+}
+
+static const struct of_device_id inno_hdmi_phy_of_match[] = {
+	{
+		.compatible = "rockchip,rk3228-hdmi-phy",
+		.data = &rk3228_hdmi_phy_drv_data
+	}, {
+		.compatible = "rockchip,rk3328-hdmi-phy",
+		.data = &rk3328_hdmi_phy_drv_data
+	}, { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, inno_hdmi_phy_of_match);
+
+static struct platform_driver inno_hdmi_phy_driver = {
+	.probe  = inno_hdmi_phy_probe,
+	.remove = inno_hdmi_phy_remove,
+	.driver = {
+		.name = "inno-hdmi-phy",
+		.of_match_table = inno_hdmi_phy_of_match,
+	},
+};
+module_platform_driver(inno_hdmi_phy_driver);
+
+MODULE_AUTHOR("Zheng Yang <zhengyang@rock-chips.com>");
+MODULE_DESCRIPTION("Innosilion HDMI 2.0 Transmitter PHY Driver");
+MODULE_LICENSE("GPL v2");