Merge intel.com:/home/lenb/bk/26-latest-ref

into intel.com:/home/lenb/src/26-latest-dev

drivers/char/Kconfig

@@ -192,7 +192,7 @@ config MOXA_INTELLIO
 
 config MOXA_SMARTIO
 	tristate "Moxa SmartIO support"
-	depends on SERIAL_NONSTANDARD && BROKEN_ON_SMP
+	depends on SERIAL_NONSTANDARD
 	help
 	  Say Y here if you have a Moxa SmartIO multiport serial card.
 

drivers/char/mxser.h

+#ifndef _MXSER_H
+#define _MXSER_H
+
+/*
+ *	Semi-public control interfaces
+ */
+ 
+/*
+ *	MOXA ioctls
+ */
+
+#define MOXA			0x400
+#define MOXA_GETDATACOUNT	(MOXA + 23)
+#define	MOXA_GET_CONF		(MOXA + 35)
+#define MOXA_DIAGNOSE		(MOXA + 50)
+#define MOXA_CHKPORTENABLE	(MOXA + 60)
+#define MOXA_HighSpeedOn	(MOXA + 61)
+#define MOXA_GET_MAJOR		(MOXA + 63)
+#define MOXA_GET_CUMAJOR	(MOXA + 64)
+#define MOXA_GETMSTATUS		(MOXA + 65)
+#define MOXA_SET_OP_MODE	(MOXA + 66)
+#define MOXA_GET_OP_MODE	(MOXA + 67)
+
+#define RS232_MODE		0
+#define RS485_2WIRE_MODE	1
+#define RS422_MODE		2
+#define RS485_4WIRE_MODE	3
+#define OP_MODE_MASK		3
+// above add by Victor Yu. 01-05-2004
+
+#define TTY_THRESHOLD_THROTTLE  128
+
+#define LO_WATER	 	(TTY_FLIPBUF_SIZE)
+#define HI_WATER		(TTY_FLIPBUF_SIZE*2*3/4)
+
+// added by James. 03-11-2004.
+#define MOXA_SDS_GETICOUNTER  	(MOXA + 68)
+#define MOXA_SDS_RSTICOUNTER  	(MOXA + 69)
+// (above) added by James.
+
+#define MOXA_ASPP_OQUEUE  	(MOXA + 70)
+#define MOXA_ASPP_SETBAUD 	(MOXA + 71)
+#define MOXA_ASPP_GETBAUD 	(MOXA + 72)
+#define MOXA_ASPP_MON     	(MOXA + 73)
+#define MOXA_ASPP_LSTATUS 	(MOXA + 74)
+#define MOXA_ASPP_MON_EXT 	(MOXA + 75)
+#define MOXA_SET_BAUD_METHOD	(MOXA + 76)
+
+
+/* --------------------------------------------------- */
+
+#define NPPI_NOTIFY_PARITY	0x01
+#define NPPI_NOTIFY_FRAMING	0x02
+#define NPPI_NOTIFY_HW_OVERRUN	0x04
+#define NPPI_NOTIFY_SW_OVERRUN	0x08
+#define NPPI_NOTIFY_BREAK	0x10
+
+#define NPPI_NOTIFY_CTSHOLD         0x01	// Tx hold by CTS low
+#define NPPI_NOTIFY_DSRHOLD         0x02	// Tx hold by DSR low
+#define NPPI_NOTIFY_XOFFHOLD        0x08	// Tx hold by Xoff received
+#define NPPI_NOTIFY_XOFFXENT        0x10	// Xoff Sent
+
+//CheckIsMoxaMust return value
+#define MOXA_OTHER_UART			0x00
+#define MOXA_MUST_MU150_HWID		0x01
+#define MOXA_MUST_MU860_HWID		0x02
+
+// follow just for Moxa Must chip define.
+//
+// when LCR register (offset 0x03) write following value,
+// the Must chip will enter enchance mode. And write value
+// on EFR (offset 0x02) bit 6,7 to change bank.
+#define MOXA_MUST_ENTER_ENCHANCE	0xBF
+
+// when enhance mode enable, access on general bank register
+#define MOXA_MUST_GDL_REGISTER		0x07
+#define MOXA_MUST_GDL_MASK		0x7F
+#define MOXA_MUST_GDL_HAS_BAD_DATA	0x80
+
+#define MOXA_MUST_LSR_RERR		0x80	// error in receive FIFO
+// enchance register bank select and enchance mode setting register
+// when LCR register equal to 0xBF
+#define MOXA_MUST_EFR_REGISTER		0x02
+// enchance mode enable
+#define MOXA_MUST_EFR_EFRB_ENABLE	0x10
+// enchance reister bank set 0, 1, 2
+#define MOXA_MUST_EFR_BANK0		0x00
+#define MOXA_MUST_EFR_BANK1		0x40
+#define MOXA_MUST_EFR_BANK2		0x80
+#define MOXA_MUST_EFR_BANK3		0xC0
+#define MOXA_MUST_EFR_BANK_MASK		0xC0
+
+// set XON1 value register, when LCR=0xBF and change to bank0
+#define MOXA_MUST_XON1_REGISTER		0x04
+
+// set XON2 value register, when LCR=0xBF and change to bank0
+#define MOXA_MUST_XON2_REGISTER		0x05
+
+// set XOFF1 value register, when LCR=0xBF and change to bank0
+#define MOXA_MUST_XOFF1_REGISTER	0x06
+
+// set XOFF2 value register, when LCR=0xBF and change to bank0
+#define MOXA_MUST_XOFF2_REGISTER	0x07
+
+#define MOXA_MUST_RBRTL_REGISTER	0x04
+#define MOXA_MUST_RBRTH_REGISTER	0x05
+#define MOXA_MUST_RBRTI_REGISTER	0x06
+#define MOXA_MUST_THRTL_REGISTER	0x07
+#define MOXA_MUST_ENUM_REGISTER		0x04
+#define MOXA_MUST_HWID_REGISTER		0x05
+#define MOXA_MUST_ECR_REGISTER		0x06
+#define MOXA_MUST_CSR_REGISTER		0x07
+
+// good data mode enable
+#define MOXA_MUST_FCR_GDA_MODE_ENABLE	0x20
+// only good data put into RxFIFO
+#define MOXA_MUST_FCR_GDA_ONLY_ENABLE	0x10
+
+// enable CTS interrupt
+#define MOXA_MUST_IER_ECTSI		0x80
+// eanble RTS interrupt
+#define MOXA_MUST_IER_ERTSI		0x40
+// enable Xon/Xoff interrupt
+#define MOXA_MUST_IER_XINT		0x20
+// enable GDA interrupt
+#define MOXA_MUST_IER_EGDAI		0x10
+
+#define MOXA_MUST_RECV_ISR		(UART_IER_RDI | MOXA_MUST_IER_EGDAI)
+
+// GDA interrupt pending
+#define MOXA_MUST_IIR_GDA		0x1C
+#define MOXA_MUST_IIR_RDA		0x04
+#define MOXA_MUST_IIR_RTO		0x0C
+#define MOXA_MUST_IIR_LSR		0x06
+
+// recieved Xon/Xoff or specical interrupt pending
+#define MOXA_MUST_IIR_XSC		0x10
+
+// RTS/CTS change state interrupt pending
+#define MOXA_MUST_IIR_RTSCTS		0x20
+#define MOXA_MUST_IIR_MASK		0x3E
+
+#define MOXA_MUST_MCR_XON_FLAG		0x40
+#define MOXA_MUST_MCR_XON_ANY		0x80
+#define MOXA_MUST_MCR_TX_XON		0x08
+
+
+// software flow control on chip mask value
+#define MOXA_MUST_EFR_SF_MASK		0x0F
+// send Xon1/Xoff1
+#define MOXA_MUST_EFR_SF_TX1		0x08
+// send Xon2/Xoff2
+#define MOXA_MUST_EFR_SF_TX2		0x04
+// send Xon1,Xon2/Xoff1,Xoff2
+#define MOXA_MUST_EFR_SF_TX12		0x0C
+// don't send Xon/Xoff
+#define MOXA_MUST_EFR_SF_TX_NO		0x00
+// Tx software flow control mask
+#define MOXA_MUST_EFR_SF_TX_MASK	0x0C
+// don't receive Xon/Xoff
+#define MOXA_MUST_EFR_SF_RX_NO		0x00
+// receive Xon1/Xoff1
+#define MOXA_MUST_EFR_SF_RX1		0x02
+// receive Xon2/Xoff2
+#define MOXA_MUST_EFR_SF_RX2		0x01
+// receive Xon1,Xon2/Xoff1,Xoff2
+#define MOXA_MUST_EFR_SF_RX12		0x03
+// Rx software flow control mask
+#define MOXA_MUST_EFR_SF_RX_MASK	0x03
+
+//#define MOXA_MUST_MIN_XOFFLIMIT               66
+//#define MOXA_MUST_MIN_XONLIMIT                20
+//#define ID1_RX_TRIG                   120
+
+
+#define CHECK_MOXA_MUST_XOFFLIMIT(info) { 	\
+	if ( (info)->IsMoxaMustChipFlag && 	\
+	 (info)->HandFlow.XoffLimit < MOXA_MUST_MIN_XOFFLIMIT ) {	\
+		(info)->HandFlow.XoffLimit = MOXA_MUST_MIN_XOFFLIMIT;	\
+		(info)->HandFlow.XonLimit = MOXA_MUST_MIN_XONLIMIT;	\
+	}	\
+}
+
+#define ENABLE_MOXA_MUST_ENCHANCE_MODE(baseio) { \
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr |= MOXA_MUST_EFR_EFRB_ENABLE;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define DISABLE_MOXA_MUST_ENCHANCE_MODE(baseio) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_EFRB_ENABLE;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define SET_MOXA_MUST_XON1_VALUE(baseio, Value) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_BANK_MASK;	\
+	__efr |= MOXA_MUST_EFR_BANK0;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb((u8)(Value), (baseio)+MOXA_MUST_XON1_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define SET_MOXA_MUST_XON2_VALUE(baseio, Value) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_BANK_MASK;	\
+	__efr |= MOXA_MUST_EFR_BANK0;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb((u8)(Value), (baseio)+MOXA_MUST_XON2_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define SET_MOXA_MUST_XOFF1_VALUE(baseio, Value) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_BANK_MASK;	\
+	__efr |= MOXA_MUST_EFR_BANK0;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb((u8)(Value), (baseio)+MOXA_MUST_XOFF1_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define SET_MOXA_MUST_XOFF2_VALUE(baseio, Value) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_BANK_MASK;	\
+	__efr |= MOXA_MUST_EFR_BANK0;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb((u8)(Value), (baseio)+MOXA_MUST_XOFF2_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define SET_MOXA_MUST_RBRTL_VALUE(baseio, Value) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_BANK_MASK;	\
+	__efr |= MOXA_MUST_EFR_BANK1;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb((u8)(Value), (baseio)+MOXA_MUST_RBRTL_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define SET_MOXA_MUST_RBRTH_VALUE(baseio, Value) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_BANK_MASK;	\
+	__efr |= MOXA_MUST_EFR_BANK1;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb((u8)(Value), (baseio)+MOXA_MUST_RBRTH_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define SET_MOXA_MUST_RBRTI_VALUE(baseio, Value) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_BANK_MASK;	\
+	__efr |= MOXA_MUST_EFR_BANK1;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb((u8)(Value), (baseio)+MOXA_MUST_RBRTI_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define SET_MOXA_MUST_THRTL_VALUE(baseio, Value) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_BANK_MASK;	\
+	__efr |= MOXA_MUST_EFR_BANK1;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb((u8)(Value), (baseio)+MOXA_MUST_THRTL_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+//#define MOXA_MUST_RBRL_VALUE  4
+#define SET_MOXA_MUST_FIFO_VALUE(info) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((info)->base+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (info)->base+UART_LCR);	\
+	__efr = inb((info)->base+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_BANK_MASK;	\
+	__efr |= MOXA_MUST_EFR_BANK1;	\
+	outb(__efr, (info)->base+MOXA_MUST_EFR_REGISTER);	\
+	outb((u8)((info)->rx_high_water), (info)->base+MOXA_MUST_RBRTH_REGISTER);	\
+	outb((u8)((info)->rx_trigger), (info)->base+MOXA_MUST_RBRTI_REGISTER);	\
+	outb((u8)((info)->rx_low_water), (info)->base+MOXA_MUST_RBRTL_REGISTER);	\
+	outb(__oldlcr, (info)->base+UART_LCR);	\
+}
+
+
+
+#define SET_MOXA_MUST_ENUM_VALUE(baseio, Value) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_BANK_MASK;	\
+	__efr |= MOXA_MUST_EFR_BANK2;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb((u8)(Value), (baseio)+MOXA_MUST_ENUM_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define GET_MOXA_MUST_HARDWARE_ID(baseio, pId) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_BANK_MASK;	\
+	__efr |= MOXA_MUST_EFR_BANK2;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	*pId = inb((baseio)+MOXA_MUST_HWID_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(baseio) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_SF_MASK;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define SET_MOXA_MUST_JUST_TX_SOFTWARE_FLOW_CONTROL(baseio) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_SF_MASK;	\
+	__efr |= MOXA_MUST_EFR_SF_TX1;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_SF_TX_MASK;	\
+	__efr |= MOXA_MUST_EFR_SF_TX1;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_SF_TX_MASK;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define SET_MOXA_MUST_JUST_RX_SOFTWARE_FLOW_CONTROL(baseio) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_SF_MASK;	\
+	__efr |= MOXA_MUST_EFR_SF_RX1;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_SF_RX_MASK;	\
+	__efr |= MOXA_MUST_EFR_SF_RX1;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_SF_RX_MASK;	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define ENABLE_MOXA_MUST_TX_RX_SOFTWARE_FLOW_CONTROL(baseio) {	\
+	u8	__oldlcr, __efr;	\
+	__oldlcr = inb((baseio)+UART_LCR);	\
+	outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR);	\
+	__efr = inb((baseio)+MOXA_MUST_EFR_REGISTER);	\
+	__efr &= ~MOXA_MUST_EFR_SF_MASK;	\
+	__efr |= (MOXA_MUST_EFR_SF_RX1|MOXA_MUST_EFR_SF_TX1);	\
+	outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER);	\
+	outb(__oldlcr, (baseio)+UART_LCR);	\
+}
+
+#define ENABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(baseio) {	\
+	u8	__oldmcr;	\
+	__oldmcr = inb((baseio)+UART_MCR);	\
+	__oldmcr |= MOXA_MUST_MCR_XON_ANY;	\
+	outb(__oldmcr, (baseio)+UART_MCR);	\
+}
+
+#define DISABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(baseio) {	\
+	u8	__oldmcr;	\
+	__oldmcr = inb((baseio)+UART_MCR);	\
+	__oldmcr &= ~MOXA_MUST_MCR_XON_ANY;	\
+	outb(__oldmcr, (baseio)+UART_MCR);	\
+}
+
+#define READ_MOXA_MUST_GDL(baseio)	inb((baseio)+MOXA_MUST_GDL_REGISTER)
+
+
+#ifndef INIT_WORK
+#define INIT_WORK(_work, _func, _data){	\
+	_data->tqueue.routine = _func;\
+	_data->tqueue.data = _data;\
+	}
+#endif
+
+#endif

drivers/scsi/sata_nv.c

@@ -218,10 +218,18 @@ static struct ata_port_operations nv_ops = {
 	.host_stop		= nv_host_stop,
 };
 
+/* FIXME: The hardware provides the necessary SATA PHY controls
+ * to support ATA_FLAG_SATA_RESET.  However, it is currently
+ * necessary to disable that flag, to solve misdetection problems.
+ * See http://bugme.osdl.org/show_bug.cgi?id=3352 for more info.
+ *
+ * This problem really needs to be investigated further.  But in the
+ * meantime, we avoid ATA_FLAG_SATA_RESET to get people working.
+ */
 static struct ata_port_info nv_port_info = {
 	.sht		= &nv_sht,
 	.host_flags	= ATA_FLAG_SATA |
-			  ATA_FLAG_SATA_RESET |
+			  /* ATA_FLAG_SATA_RESET | */
 			  ATA_FLAG_SRST |
 			  ATA_FLAG_NO_LEGACY,
 	.pio_mask	= NV_PIO_MASK,

drivers/usb/atm/usb_atm.c

@@ -111,7 +111,7 @@ static int udsl_print_packet(const unsigned char *data, int len);
 
 #define DRIVER_AUTHOR	"Johan Verrept, Duncan Sands <duncan.sands@free.fr>"
 #define DRIVER_VERSION	"1.8"
-#define DRIVER_DESC	"Alcatel SpeedTouch USB driver version " DRIVER_VERSION
+#define DRIVER_DESC	"Generic USB ATM/DSL I/O, version " DRIVER_VERSION
 
 static unsigned int num_rcv_urbs = UDSL_DEFAULT_RCV_URBS;
 static unsigned int num_snd_urbs = UDSL_DEFAULT_SND_URBS;
@@ -386,10 +386,6 @@ static unsigned int udsl_write_cells(struct udsl_instance_data *instance,
 	if (!(ctrl->num_cells -= ne) || !(howmany -= ne))
 		goto out;
 
-	if (instance->snd_padding) {
-		memset(target, 0, instance->snd_padding);
-		target += instance->snd_padding;
-	}
 	udsl_fill_cell_header(target, ctrl->atm_data.vcc);
 	target += ATM_CELL_HEADER;
 	memcpy(target, skb->data, skb->len);
@@ -404,6 +400,10 @@ static unsigned int udsl_write_cells(struct udsl_instance_data *instance,
 			goto out;
 		}
 
+		if (instance->snd_padding) {
+			memset(target, 0, instance->snd_padding);
+			target += instance->snd_padding;
+		}
 		udsl_fill_cell_header(target, ctrl->atm_data.vcc);
 		target += ATM_CELL_HEADER;
 		memset(target, 0, ATM_CELL_PAYLOAD - ATM_AAL5_TRAILER);

drivers/usb/serial/keyspan.c

@@ -1121,7 +1121,7 @@ static inline void stop_urb(struct urb *urb)
 {
 	if (urb && urb->status == -EINPROGRESS) {
 		urb->transfer_flags &= ~URB_ASYNC_UNLINK;
-		usb_unlink_urb(urb);
+		usb_kill_urb(urb);
 	}
 }
 

include/linux/pci_ids.h

@@ -1799,8 +1799,21 @@
 #define PCI_DEVICE_ID_APPLICOM_PCI2000PFB 0x0003
 
 #define PCI_VENDOR_ID_MOXA		0x1393
+#define PCI_DEVICE_ID_MOXA_RC7000	0x0001
+#define PCI_DEVICE_ID_MOXA_CP102	0x1020
+#define PCI_DEVICE_ID_MOXA_CP102UL	0x1021
+#define PCI_DEVICE_ID_MOXA_CP102U	0x1022
 #define PCI_DEVICE_ID_MOXA_C104		0x1040
+#define PCI_DEVICE_ID_MOXA_CP104U	0x1041
+#define PCI_DEVICE_ID_MOXA_CP104JU	0x1042
+#define PCI_DEVICE_ID_MOXA_CT114	0x1140
+#define PCI_DEVICE_ID_MOXA_CP114	0x1141
+#define PCI_DEVICE_ID_MOXA_CP118U	0x1180
+#define PCI_DEVICE_ID_MOXA_CP132	0x1320
+#define PCI_DEVICE_ID_MOXA_CP132U	0x1321
+#define PCI_DEVICE_ID_MOXA_CP134U	0x1340
 #define PCI_DEVICE_ID_MOXA_C168		0x1680
+#define PCI_DEVICE_ID_MOXA_CP168U	0x1681
 #define PCI_DEVICE_ID_MOXA_CP204J	0x2040
 #define PCI_DEVICE_ID_MOXA_C218		0x2180
 #define PCI_DEVICE_ID_MOXA_C320		0x3200

sound/core/pcm_misc.c

@@ -25,11 +25,14 @@
 #include <sound/pcm.h>
 #define SND_PCM_FORMAT_UNKNOWN (-1)
 
+/* NOTE: "signed" prefix must be given below since the default char is
+ *       unsigned on some architectures!
+ */
 struct pcm_format_data {
-	char width;	/* bit width */
-	char phys;	/* physical bit width */
-	char le;	/* 0 = big-endian, 1 = little-endian, -1 = others */
-	char signd;	/* 0 = unsigned, 1 = signed, -1 = others */
+	unsigned char width;	/* bit width */
+	unsigned char phys;	/* physical bit width */
+	signed char le;	/* 0 = big-endian, 1 = little-endian, -1 = others */
+	signed char signd;	/* 0 = unsigned, 1 = signed, -1 = others */
 	unsigned char silence[8];	/* silence data to fill */
 };