Commit 5e96adec authored by Eric Miao's avatar Eric Miao Committed by Russell King

[ARM] pxa/spitz: convert to use new MFP API

Original patch from Dmitry Baryshkov's initial scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.

TODO: figure out the MFP configuration of the SSP2 which looks like
to be already configured by the boot loader, though.
Signed-off-by: default avatarDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: default avatarEric Miao <eric.miao@marvell.com>
Signed-off-by: default avatarRussell King <rmk+kernel@arm.linux.org.uk>
parent dd5980d6
......@@ -38,7 +38,7 @@
#include <mach/pxa-regs.h>
#include <mach/pxa2xx-regs.h>
#include <mach/pxa2xx-gpio.h>
#include <mach/mfp-pxa27x.h>
#include <mach/pxa27x-udc.h>
#include <mach/reset.h>
#include <mach/i2c.h>
......@@ -58,6 +58,66 @@
#include "devices.h"
#include "sharpsl.h"
static unsigned long spitz_pin_config[] __initdata = {
/* Chip Selects */
GPIO78_nCS_2, /* SCOOP #2 */
GPIO80_nCS_4, /* SCOOP #1 */
/* LCD - 16bpp Active TFT */
GPIO58_LCD_LDD_0,
GPIO59_LCD_LDD_1,
GPIO60_LCD_LDD_2,
GPIO61_LCD_LDD_3,
GPIO62_LCD_LDD_4,
GPIO63_LCD_LDD_5,
GPIO64_LCD_LDD_6,
GPIO65_LCD_LDD_7,
GPIO66_LCD_LDD_8,
GPIO67_LCD_LDD_9,
GPIO68_LCD_LDD_10,
GPIO69_LCD_LDD_11,
GPIO70_LCD_LDD_12,
GPIO71_LCD_LDD_13,
GPIO72_LCD_LDD_14,
GPIO73_LCD_LDD_15,
GPIO74_LCD_FCLK,
GPIO75_LCD_LCLK,
GPIO76_LCD_PCLK,
/* PC Card */
GPIO48_nPOE,
GPIO49_nPWE,
GPIO50_nPIOR,
GPIO51_nPIOW,
GPIO85_nPCE_1,
GPIO54_nPCE_2,
GPIO79_PSKTSEL,
GPIO55_nPREG,
GPIO56_nPWAIT,
GPIO57_nIOIS16,
/* MMC */
GPIO32_MMC_CLK,
GPIO112_MMC_CMD,
GPIO92_MMC_DAT_0,
GPIO109_MMC_DAT_1,
GPIO110_MMC_DAT_2,
GPIO111_MMC_DAT_3,
/* GPIOs */
GPIO9_GPIO, /* SPITZ_GPIO_nSD_DETECT */
GPIO81_GPIO, /* SPITZ_GPIO_nSD_WP */
GPIO41_GPIO, /* SPITZ_GPIO_USB_CONNECT */
GPIO37_GPIO, /* SPITZ_GPIO_USB_HOST */
GPIO35_GPIO, /* SPITZ_GPIO_USB_DEVICE */
GPIO22_GPIO, /* SPITZ_GPIO_HSYNC */
GPIO94_GPIO, /* SPITZ_GPIO_CF_CD */
GPIO105_GPIO, /* SPITZ_GPIO_CF_IRQ */
GPIO106_GPIO, /* SPITZ_GPIO_CF2_IRQ */
GPIO1_GPIO | WAKEUP_ON_EDGE_RISE,
};
/*
* Spitz SCOOP Device #1
*/
......@@ -146,27 +206,6 @@ static void spitz_card_pwr_ctrl(int device, unsigned short new_cpr)
}
}
static void spitz_pcmcia_init(void)
{
/* Setup default state of GPIO outputs
before we enable them as outputs. */
GPSR(GPIO48_nPOE) = GPIO_bit(GPIO48_nPOE) |
GPIO_bit(GPIO49_nPWE) | GPIO_bit(GPIO50_nPIOR) |
GPIO_bit(GPIO51_nPIOW) | GPIO_bit(GPIO54_nPCE_2);
GPSR(GPIO85_nPCE_1) = GPIO_bit(GPIO85_nPCE_1);
pxa_gpio_mode(GPIO48_nPOE_MD);
pxa_gpio_mode(GPIO49_nPWE_MD);
pxa_gpio_mode(GPIO50_nPIOR_MD);
pxa_gpio_mode(GPIO51_nPIOW_MD);
pxa_gpio_mode(GPIO55_nPREG_MD);
pxa_gpio_mode(GPIO56_nPWAIT_MD);
pxa_gpio_mode(GPIO57_nIOIS16_MD);
pxa_gpio_mode(GPIO85_nPCE_1_MD);
pxa_gpio_mode(GPIO54_nPCE_2_MD);
pxa_gpio_mode(GPIO104_pSKTSEL_MD);
}
static void spitz_pcmcia_pwr(struct device *scoop, unsigned short cpr, int nr)
{
/* Only need to override behaviour for slot 0 */
......@@ -192,7 +231,6 @@ static struct scoop_pcmcia_dev spitz_pcmcia_scoop[] = {
static struct scoop_pcmcia_config spitz_pcmcia_config = {
.devs = &spitz_pcmcia_scoop[0],
.num_devs = 2,
.pcmcia_init = spitz_pcmcia_init,
.power_ctrl = spitz_pcmcia_pwr,
};
......@@ -365,14 +403,6 @@ static int spitz_mci_init(struct device *dev, irq_handler_t spitz_detect_int, vo
{
int err;
/* setup GPIO for PXA27x MMC controller */
pxa_gpio_mode(GPIO32_MMCCLK_MD);
pxa_gpio_mode(GPIO112_MMCCMD_MD);
pxa_gpio_mode(GPIO92_MMCDAT0_MD);
pxa_gpio_mode(GPIO109_MMCDAT1_MD);
pxa_gpio_mode(GPIO110_MMCDAT2_MD);
pxa_gpio_mode(GPIO111_MMCDAT3_MD);
err = gpio_request(SPITZ_GPIO_nSD_DETECT, "nSD_DETECT");
if (err)
goto err_out;
......@@ -447,12 +477,9 @@ static int spitz_ohci_init(struct device *dev)
if (err)
return err;
/* Only Port 2 is connected */
pxa_gpio_mode(SPITZ_GPIO_USB_CONNECT | GPIO_IN);
pxa_gpio_mode(SPITZ_GPIO_USB_HOST | GPIO_OUT);
pxa_gpio_mode(SPITZ_GPIO_USB_DEVICE | GPIO_IN);
/* Setup USB Port 2 Output Control Register */
/* Only Port 2 is connected
* Setup USB Port 2 Output Control Register
*/
UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
gpio_direction_output(SPITZ_GPIO_USB_HOST, 1);
......@@ -582,20 +609,12 @@ static void __init common_init(void)
PMCR = 0x00;
/* setup sleep mode values */
PWER = 0x00000002;
PFER = 0x00000000;
PRER = 0x00000002;
PGSR0 = 0x0158C000;
PGSR1 = 0x00FF0080;
PGSR2 = 0x0001C004;
/* Stop 3.6MHz and drive HIGH to PCMCIA and CS */
PCFR |= PCFR_OPDE;
corgi_ssp_set_machinfo(&spitz_ssp_machinfo);
pxa2xx_mfp_config(ARRAY_AND_SIZE(spitz_pin_config));
pxa_gpio_mode(SPITZ_GPIO_HSYNC | GPIO_IN);
corgi_ssp_set_machinfo(&spitz_ssp_machinfo);
platform_add_devices(devices, ARRAY_SIZE(devices));
pxa_set_mci_info(&spitz_mci_platform_data);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment