Merge branch 'linux-2.6.33.y' of git://git.kernel.org/pub/scm/linux/kernel/git/inaky/wimax

drivers/net/wimax/i2400m/control.c

@@ -54,7 +54,7 @@
  *   i2400m_set_init_config()
  *   i2400m_cmd_get_state()
  * i2400m_dev_shutdown()        Called by i2400m_dev_stop()
- *   i2400m->bus_reset()
+ *   i2400m_reset()
  *
  * i2400m_{cmd,get,set}_*()
  *   i2400m_msg_to_dev()
@@ -82,6 +82,13 @@
 #define D_SUBMODULE control
 #include "debug-levels.h"
 
+int i2400m_passive_mode;	/* 0 (passive mode disabled) by default */
+module_param_named(passive_mode, i2400m_passive_mode, int, 0644);
+MODULE_PARM_DESC(passive_mode,
+		 "If true, the driver will not do any device setup "
+		 "and leave it up to user space, who must be properly "
+		 "setup.");
+
 
 /*
  * Return if a TLV is of a give type and size
@@ -263,7 +270,7 @@ int i2400m_msg_check_status(const struct i2400m_l3l4_hdr *l3l4_hdr,
 
 	if (status == 0)
 		return 0;
-	if (status > ARRAY_SIZE(ms_to_errno)) {
+	if (status >= ARRAY_SIZE(ms_to_errno)) {
 		str = "unknown status code";
 		result = -EBADR;
 	} else {
@@ -336,7 +343,7 @@ void i2400m_report_tlv_system_state(struct i2400m *i2400m,
 		/* Huh? just in case, shut it down */
 		dev_err(dev, "HW BUG? unknown state %u: shutting down\n",
 			i2400m_state);
-		i2400m->bus_reset(i2400m, I2400M_RT_WARM);
+		i2400m_reset(i2400m, I2400M_RT_WARM);
 		break;
 	};
 	d_fnend(3, dev, "(i2400m %p ss %p [%u]) = void\n",
@@ -1335,6 +1342,8 @@ int i2400m_dev_initialize(struct i2400m *i2400m)
 	unsigned argc = 0;
 
 	d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
+	if (i2400m_passive_mode)
+		goto out_passive;
 	/* Disable idle mode? (enabled by default) */
 	if (i2400m_idle_mode_disabled) {
 		if (i2400m_le_v1_3(i2400m)) {
@@ -1377,6 +1386,7 @@ int i2400m_dev_initialize(struct i2400m *i2400m)
 	result = i2400m_set_init_config(i2400m, args, argc);
 	if (result < 0)
 		goto error;
+out_passive:
 	/*
 	 * Update state: Here it just calls a get state; parsing the
 	 * result (System State TLV and RF Status TLV [done in the rx

drivers/net/wimax/i2400m/debugfs.c

@@ -214,7 +214,7 @@ int debugfs_i2400m_reset_set(void *data, u64 val)
 	case I2400M_RT_WARM:
 	case I2400M_RT_COLD:
 	case I2400M_RT_BUS:
-		result = i2400m->bus_reset(i2400m, rt);
+		result = i2400m_reset(i2400m, rt);
 		if (result >= 0)
 			result = 0;
 	default:

drivers/net/wimax/i2400m/driver.c

@@ -41,8 +41,10 @@
  *     __i2400m_dev_start()
  *
  * i2400m_setup()
+ *   i2400m->bus_setup()
  *   i2400m_bootrom_init()
  *   register_netdev()
+ *   wimax_dev_add()
  *   i2400m_dev_start()
  *     __i2400m_dev_start()
  *       i2400m_dev_bootstrap()
@@ -50,15 +52,15 @@
  *       i2400m->bus_dev_start()
  *       i2400m_firmware_check()
  *       i2400m_check_mac_addr()
- *   wimax_dev_add()
  *
  * i2400m_release()
- *   wimax_dev_rm()
  *   i2400m_dev_stop()
  *     __i2400m_dev_stop()
  *       i2400m_dev_shutdown()
  *       i2400m->bus_dev_stop()
  *       i2400m_tx_release()
+ *   i2400m->bus_release()
+ *   wimax_dev_rm()
  *   unregister_netdev()
  */
 #include "i2400m.h"
@@ -66,6 +68,7 @@
 #include <linux/wimax/i2400m.h>
 #include <linux/module.h>
 #include <linux/moduleparam.h>
+#include <linux/suspend.h>
 
 #define D_SUBMODULE driver
 #include "debug-levels.h"
@@ -90,76 +93,39 @@ MODULE_PARM_DESC(power_save_disabled,
 		 "False by default (so the device is told to do power "
 		 "saving).");
 
-/**
- * i2400m_queue_work - schedule work on a i2400m's queue
- *
- * @i2400m: device descriptor
- *
- * @fn: function to run to execute work. It gets passed a 'struct
- *     work_struct' that is wrapped in a 'struct i2400m_work'. Once
- *     done, you have to (1) i2400m_put(i2400m_work->i2400m) and then
- *     (2) kfree(i2400m_work).
- *
- * @gfp_flags: GFP flags for memory allocation.
- *
- * @pl: pointer to a payload buffer that you want to pass to the _work
- *     function. Use this to pack (for example) a struct with extra
- *     arguments.
- *
- * @pl_size: size of the payload buffer.
- *
- * We do this quite often, so this just saves typing; allocate a
- * wrapper for a i2400m, get a ref to it, pack arguments and launch
- * the work.
- *
- * A usual workflow is:
- *
- * struct my_work_args {
- *         void *something;
- *         int whatever;
- * };
- * ...
- *
- * struct my_work_args my_args = {
- *         .something = FOO,
- *         .whaetever = BLAH
- * };
- * i2400m_queue_work(i2400m, 1, my_work_function, GFP_KERNEL,
- *                   &args, sizeof(args))
- *
- * And now the work function can unpack the arguments and call the
- * real function (or do the job itself):
- *
- * static
- * void my_work_fn((struct work_struct *ws)
- * {
- *         struct i2400m_work *iw =
- *	           container_of(ws, struct i2400m_work, ws);
- *	   struct my_work_args *my_args = (void *) iw->pl;
- *
- *	   my_work(iw->i2400m, my_args->something, my_args->whatevert);
- * }
- */
-int i2400m_queue_work(struct i2400m *i2400m,
-		      void (*fn)(struct work_struct *), gfp_t gfp_flags,
-		      const void *pl, size_t pl_size)
+static char i2400m_debug_params[128];
+module_param_string(debug, i2400m_debug_params, sizeof(i2400m_debug_params),
+		    0644);
+MODULE_PARM_DESC(debug,
+		 "String of space-separated NAME:VALUE pairs, where NAMEs "
+		 "are the different debug submodules and VALUE are the "
+		 "initial debug value to set.");
+
+static char i2400m_barkers_params[128];
+module_param_string(barkers, i2400m_barkers_params,
+		    sizeof(i2400m_barkers_params), 0644);
+MODULE_PARM_DESC(barkers,
+		 "String of comma-separated 32-bit values; each is "
+		 "recognized as the value the device sends as a reboot "
+		 "signal; values are appended to a list--setting one value "
+		 "as zero cleans the existing list and starts a new one.");
+
+static
+struct i2400m_work *__i2400m_work_setup(
+	struct i2400m *i2400m, void (*fn)(struct work_struct *),
+	gfp_t gfp_flags, const void *pl, size_t pl_size)
 {
-	int result;
 	struct i2400m_work *iw;
 
-	BUG_ON(i2400m->work_queue == NULL);
-	result = -ENOMEM;
 	iw = kzalloc(sizeof(*iw) + pl_size, gfp_flags);
 	if (iw == NULL)
-		goto error_kzalloc;
+		return NULL;
 	iw->i2400m = i2400m_get(i2400m);
+	iw->pl_size = pl_size;
 	memcpy(iw->pl, pl, pl_size);
 	INIT_WORK(&iw->ws, fn);
-	result = queue_work(i2400m->work_queue, &iw->ws);
-error_kzalloc:
-	return result;
+	return iw;
 }
-EXPORT_SYMBOL_GPL(i2400m_queue_work);
 
 
 /*
@@ -175,21 +141,19 @@ EXPORT_SYMBOL_GPL(i2400m_queue_work);
  * it should not happen.
  */
 int i2400m_schedule_work(struct i2400m *i2400m,
-			 void (*fn)(struct work_struct *), gfp_t gfp_flags)
+			 void (*fn)(struct work_struct *), gfp_t gfp_flags,
+			 const void *pl, size_t pl_size)
 {
 	int result;
 	struct i2400m_work *iw;
 
 	result = -ENOMEM;
-	iw = kzalloc(sizeof(*iw), gfp_flags);
-	if (iw == NULL)
-		goto error_kzalloc;
-	iw->i2400m = i2400m_get(i2400m);
-	INIT_WORK(&iw->ws, fn);
-	result = schedule_work(&iw->ws);
-	if (result == 0)
-		result = -ENXIO;
-error_kzalloc:
+	iw = __i2400m_work_setup(i2400m, fn, gfp_flags, pl, pl_size);
+	if (iw != NULL) {
+		result = schedule_work(&iw->ws);
+		if (WARN_ON(result == 0))
+			result = -ENXIO;
+	}
 	return result;
 }
 
@@ -291,7 +255,7 @@ int i2400m_op_reset(struct wimax_dev *wimax_dev)
 	mutex_lock(&i2400m->init_mutex);
 	i2400m->reset_ctx = &ctx;
 	mutex_unlock(&i2400m->init_mutex);
-	result = i2400m->bus_reset(i2400m, I2400M_RT_WARM);
+	result = i2400m_reset(i2400m, I2400M_RT_WARM);
 	if (result < 0)
 		goto out;
 	result = wait_for_completion_timeout(&ctx.completion, 4*HZ);
@@ -420,9 +384,15 @@ int __i2400m_dev_start(struct i2400m *i2400m, enum i2400m_bri flags)
 		dev_err(dev, "cannot create workqueue\n");
 		goto error_create_workqueue;
 	}
-	result = i2400m->bus_dev_start(i2400m);
-	if (result < 0)
-		goto error_bus_dev_start;
+	if (i2400m->bus_dev_start) {
+		result = i2400m->bus_dev_start(i2400m);
+		if (result < 0)
+			goto error_bus_dev_start;
+	}
+	i2400m->ready = 1;
+	wmb();		/* see i2400m->ready's documentation  */
+	/* process pending reports from the device */
+	queue_work(i2400m->work_queue, &i2400m->rx_report_ws);
 	result = i2400m_firmware_check(i2400m);	/* fw versions ok? */
 	if (result < 0)
 		goto error_fw_check;
@@ -430,8 +400,6 @@ int __i2400m_dev_start(struct i2400m *i2400m, enum i2400m_bri flags)
 	result = i2400m_check_mac_addr(i2400m);
 	if (result < 0)
 		goto error_check_mac_addr;
-	i2400m->ready = 1;
-	wimax_state_change(wimax_dev, WIMAX_ST_UNINITIALIZED);
 	result = i2400m_dev_initialize(i2400m);
 	if (result < 0)
 		goto error_dev_initialize;
@@ -443,8 +411,12 @@ int __i2400m_dev_start(struct i2400m *i2400m, enum i2400m_bri flags)
 
 error_dev_initialize:
 error_check_mac_addr:
+	i2400m->ready = 0;
+	wmb();		/* see i2400m->ready's documentation  */
+	flush_workqueue(i2400m->work_queue);
 error_fw_check:
-	i2400m->bus_dev_stop(i2400m);
+	if (i2400m->bus_dev_stop)
+		i2400m->bus_dev_stop(i2400m);
 error_bus_dev_start:
 	destroy_workqueue(i2400m->work_queue);
 error_create_workqueue:
@@ -466,11 +438,15 @@ int __i2400m_dev_start(struct i2400m *i2400m, enum i2400m_bri flags)
 static
 int i2400m_dev_start(struct i2400m *i2400m, enum i2400m_bri bm_flags)
 {
-	int result;
+	int result = 0;
 	mutex_lock(&i2400m->init_mutex);	/* Well, start the device */
-	result = __i2400m_dev_start(i2400m, bm_flags);
-	if (result >= 0)
-		i2400m->updown = 1;
+	if (i2400m->updown == 0) {
+		result = __i2400m_dev_start(i2400m, bm_flags);
+		if (result >= 0) {
+			i2400m->updown = 1;
+			wmb();	/* see i2400m->updown's documentation */
+		}
+	}
 	mutex_unlock(&i2400m->init_mutex);
 	return result;
 }
@@ -495,9 +471,20 @@ void __i2400m_dev_stop(struct i2400m *i2400m)
 
 	d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
 	wimax_state_change(wimax_dev, __WIMAX_ST_QUIESCING);
+	i2400m_msg_to_dev_cancel_wait(i2400m, -EL3RST);
+	complete(&i2400m->msg_completion);
+	i2400m_net_wake_stop(i2400m);
 	i2400m_dev_shutdown(i2400m);
-	i2400m->ready = 0;
-	i2400m->bus_dev_stop(i2400m);
+	/*
+	 * Make sure no report hooks are running *before* we stop the
+	 * communication infrastructure with the device.
+	 */
+	i2400m->ready = 0;	/* nobody can queue work anymore */
+	wmb();		/* see i2400m->ready's documentation  */
+	flush_workqueue(i2400m->work_queue);
+
+	if (i2400m->bus_dev_stop)
+		i2400m->bus_dev_stop(i2400m);
 	destroy_workqueue(i2400m->work_queue);
 	i2400m_rx_release(i2400m);
 	i2400m_tx_release(i2400m);
@@ -518,11 +505,138 @@ void i2400m_dev_stop(struct i2400m *i2400m)
 	if (i2400m->updown) {
 		__i2400m_dev_stop(i2400m);
 		i2400m->updown = 0;
+		wmb();	/* see i2400m->updown's documentation  */
 	}
 	mutex_unlock(&i2400m->init_mutex);
 }
 
 
+/*
+ * Listen to PM events to cache the firmware before suspend/hibernation
+ *
+ * When the device comes out of suspend, it might go into reset and
+ * firmware has to be uploaded again. At resume, most of the times, we
+ * can't load firmware images from disk, so we need to cache it.
+ *
+ * i2400m_fw_cache() will allocate a kobject and attach the firmware
+ * to it; that way we don't have to worry too much about the fw loader
+ * hitting a race condition.
+ *
+ * Note: modus operandi stolen from the Orinoco driver; thx.
+ */
+static
+int i2400m_pm_notifier(struct notifier_block *notifier,
+		       unsigned long pm_event,
+		       void *unused)
+{
+	struct i2400m *i2400m =
+		container_of(notifier, struct i2400m, pm_notifier);
+	struct device *dev = i2400m_dev(i2400m);
+
+	d_fnstart(3, dev, "(i2400m %p pm_event %lx)\n", i2400m, pm_event);
+	switch (pm_event) {
+	case PM_HIBERNATION_PREPARE:
+	case PM_SUSPEND_PREPARE:
+		i2400m_fw_cache(i2400m);
+		break;
+	case PM_POST_RESTORE:
+		/* Restore from hibernation failed. We need to clean
+		 * up in exactly the same way, so fall through. */
+	case PM_POST_HIBERNATION:
+	case PM_POST_SUSPEND:
+		i2400m_fw_uncache(i2400m);
+		break;
+
+	case PM_RESTORE_PREPARE:
+	default:
+		break;
+	}
+	d_fnend(3, dev, "(i2400m %p pm_event %lx) = void\n", i2400m, pm_event);
+	return NOTIFY_DONE;
+}
+
+
+/*
+ * pre-reset is called before a device is going on reset
+ *
+ * This has to be followed by a call to i2400m_post_reset(), otherwise
+ * bad things might happen.
+ */
+int i2400m_pre_reset(struct i2400m *i2400m)
+{
+	int result;
+	struct device *dev = i2400m_dev(i2400m);
+
+	d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
+	d_printf(1, dev, "pre-reset shut down\n");
+
+	result = 0;
+	mutex_lock(&i2400m->init_mutex);
+	if (i2400m->updown) {
+		netif_tx_disable(i2400m->wimax_dev.net_dev);
+		__i2400m_dev_stop(i2400m);
+		result = 0;
+		/* down't set updown to zero -- this way
+		 * post_reset can restore properly */
+	}
+	mutex_unlock(&i2400m->init_mutex);
+	if (i2400m->bus_release)
+		i2400m->bus_release(i2400m);
+	d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
+	return result;
+}
+EXPORT_SYMBOL_GPL(i2400m_pre_reset);
+
+
+/*
+ * Restore device state after a reset
+ *
+ * Do the work needed after a device reset to bring it up to the same
+ * state as it was before the reset.
+ *
+ * NOTE: this requires i2400m->init_mutex taken
+ */
+int i2400m_post_reset(struct i2400m *i2400m)
+{
+	int result = 0;
+	struct device *dev = i2400m_dev(i2400m);
+
+	d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
+	d_printf(1, dev, "post-reset start\n");
+	if (i2400m->bus_setup) {
+		result = i2400m->bus_setup(i2400m);
+		if (result < 0) {
+			dev_err(dev, "bus-specific setup failed: %d\n",
+				result);
+			goto error_bus_setup;
+		}
+	}
+	mutex_lock(&i2400m->init_mutex);
+	if (i2400m->updown) {
+		result = __i2400m_dev_start(
+			i2400m, I2400M_BRI_SOFT | I2400M_BRI_MAC_REINIT);
+		if (result < 0)
+			goto error_dev_start;
+	}
+	mutex_unlock(&i2400m->init_mutex);
+	d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
+	return result;
+
+error_dev_start:
+	if (i2400m->bus_release)
+		i2400m->bus_release(i2400m);
+error_bus_setup:
+	/* even if the device was up, it could not be recovered, so we
+	 * mark it as down. */
+	i2400m->updown = 0;
+	wmb();		/* see i2400m->updown's documentation  */
+	mutex_unlock(&i2400m->init_mutex);
+	d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
+	return result;
+}
+EXPORT_SYMBOL_GPL(i2400m_post_reset);
+
+
 /*
  * The device has rebooted; fix up the device and the driver
  *
@@ -542,56 +656,69 @@ void i2400m_dev_stop(struct i2400m *i2400m)
  *       _stop()], don't do anything, let it fail and handle it.
  *
  * This function is ran always in a thread context
+ *
+ * This function gets passed, as payload to i2400m_work() a 'const
+ * char *' ptr with a "reason" why the reset happened (for messages).
  */
 static
 void __i2400m_dev_reset_handle(struct work_struct *ws)
 {
 	int result;
 	struct i2400m_work *iw = container_of(ws, struct i2400m_work, ws);
+	const char *reason;
 	struct i2400m *i2400m = iw->i2400m;
 	struct device *dev = i2400m_dev(i2400m);
-	enum wimax_st wimax_state;
 	struct i2400m_reset_ctx *ctx = i2400m->reset_ctx;
 
-	d_fnstart(3, dev, "(ws %p i2400m %p)\n", ws, i2400m);
+	if (WARN_ON(iw->pl_size != sizeof(reason)))
+		reason = "SW BUG: reason n/a";
+	else
+		memcpy(&reason, iw->pl, sizeof(reason));
+
+	d_fnstart(3, dev, "(ws %p i2400m %p reason %s)\n", ws, i2400m, reason);
+
 	result = 0;
 	if (mutex_trylock(&i2400m->init_mutex) == 0) {
 		/* We are still in i2400m_dev_start() [let it fail] or
 		 * i2400m_dev_stop() [we are shutting down anyway, so
 		 * ignore it] or we are resetting somewhere else. */
-		dev_err(dev, "device rebooted\n");
+		dev_err(dev, "device rebooted somewhere else?\n");
 		i2400m_msg_to_dev_cancel_wait(i2400m, -EL3RST);
 		complete(&i2400m->msg_completion);
 		goto out;
 	}
-	wimax_state = wimax_state_get(&i2400m->wimax_dev);
-	if (wimax_state < WIMAX_ST_UNINITIALIZED) {
-		dev_info(dev, "device rebooted: it is down, ignoring\n");
-		goto out_unlock;	/* ifconfig up/down wasn't called */
+	if (i2400m->updown == 0)  {
+		dev_info(dev, "%s: device is down, doing nothing\n", reason);
+		goto out_unlock;
 	}
-	dev_err(dev, "device rebooted: reinitializing driver\n");
+	dev_err(dev, "%s: reinitializing driver\n", reason);
 	__i2400m_dev_stop(i2400m);
-	i2400m->updown = 0;
 	result = __i2400m_dev_start(i2400m,
 				    I2400M_BRI_SOFT | I2400M_BRI_MAC_REINIT);
 	if (result < 0) {
-		dev_err(dev, "device reboot: cannot start the device: %d\n",
-			result);
-		result = i2400m->bus_reset(i2400m, I2400M_RT_BUS);
-		if (result >= 0)
-			result = -ENODEV;
-	} else
-		i2400m->updown = 1;
+		i2400m->updown = 0;
+		wmb();		/* see i2400m->updown's documentation  */
+		dev_err(dev, "%s: cannot start the device: %d\n",
+			reason, result);
+		result = -EUCLEAN;
+	}
 out_unlock:
 	if (i2400m->reset_ctx) {
 		ctx->result = result;
 		complete(&ctx->completion);
 	}
 	mutex_unlock(&i2400m->init_mutex);
+	if (result == -EUCLEAN) {
+		/* ops, need to clean up [w/ init_mutex not held] */
+		result = i2400m_reset(i2400m, I2400M_RT_BUS);
+		if (result >= 0)
+			result = -ENODEV;
+	}
 out:
 	i2400m_put(i2400m);
 	kfree(iw);
-	d_fnend(3, dev, "(ws %p i2400m %p) = void\n", ws, i2400m);
+	d_fnend(3, dev, "(ws %p i2400m %p reason %s) = void\n",
+		ws, i2400m, reason);
 	return;
 }
 
@@ -608,16 +735,104 @@ void __i2400m_dev_reset_handle(struct work_struct *ws)
  * reinitializing the driver to handle the reset, calling into the
  * bus-specific functions ops as needed.
  */
-int i2400m_dev_reset_handle(struct i2400m *i2400m)
+int i2400m_dev_reset_handle(struct i2400m *i2400m, const char *reason)
 {
 	i2400m->boot_mode = 1;
 	wmb();		/* Make sure i2400m_msg_to_dev() sees boot_mode */
 	return i2400m_schedule_work(i2400m, __i2400m_dev_reset_handle,
-				    GFP_ATOMIC);
+				    GFP_ATOMIC, &reason, sizeof(reason));
 }
 EXPORT_SYMBOL_GPL(i2400m_dev_reset_handle);
 
 
+/*
+ * Alloc the command and ack buffers for boot mode
+ *
+ * Get the buffers needed to deal with boot mode messages.  These
+ * buffers need to be allocated before the sdio recieve irq is setup.
+ */
+static
+int i2400m_bm_buf_alloc(struct i2400m *i2400m)
+{
+	int result;
+
+	result = -ENOMEM;
+	i2400m->bm_cmd_buf = kzalloc(I2400M_BM_CMD_BUF_SIZE, GFP_KERNEL);
+	if (i2400m->bm_cmd_buf == NULL)
+		goto error_bm_cmd_kzalloc;
+	i2400m->bm_ack_buf = kzalloc(I2400M_BM_ACK_BUF_SIZE, GFP_KERNEL);
+	if (i2400m->bm_ack_buf == NULL)
+		goto error_bm_ack_buf_kzalloc;
+	return 0;
+
+error_bm_ack_buf_kzalloc:
+	kfree(i2400m->bm_cmd_buf);
+error_bm_cmd_kzalloc:
+	return result;
+}
+
+
+/*
+ * Free boot mode command and ack buffers.
+ */
+static
+void i2400m_bm_buf_free(struct i2400m *i2400m)
+{
+	kfree(i2400m->bm_ack_buf);
+	kfree(i2400m->bm_cmd_buf);
+}
+
+
+/**
+ * i2400m_init - Initialize a 'struct i2400m' from all zeroes
+ *
+ * This is a bus-generic API call.
+ */
+void i2400m_init(struct i2400m *i2400m)
+{
+	wimax_dev_init(&i2400m->wimax_dev);
+
+	i2400m->boot_mode = 1;
+	i2400m->rx_reorder = 1;
+	init_waitqueue_head(&i2400m->state_wq);
+
+	spin_lock_init(&i2400m->tx_lock);
+	i2400m->tx_pl_min = UINT_MAX;
+	i2400m->tx_size_min = UINT_MAX;
+
+	spin_lock_init(&i2400m->rx_lock);
+	i2400m->rx_pl_min = UINT_MAX;
+	i2400m->rx_size_min = UINT_MAX;
+	INIT_LIST_HEAD(&i2400m->rx_reports);
+	INIT_WORK(&i2400m->rx_report_ws, i2400m_report_hook_work);
+
+	mutex_init(&i2400m->msg_mutex);
+	init_completion(&i2400m->msg_completion);
+
+	mutex_init(&i2400m->init_mutex);
+	/* wake_tx_ws is initialized in i2400m_tx_setup() */
+}
+EXPORT_SYMBOL_GPL(i2400m_init);
+
+
+int i2400m_reset(struct i2400m *i2400m, enum i2400m_reset_type rt)
+{
+	struct net_device *net_dev = i2400m->wimax_dev.net_dev;
+
+	/*
+	 * Make sure we stop TXs and down the carrier before
+	 * resetting; this is needed to avoid things like
+	 * i2400m_wake_tx() scheduling stuff in parallel.
+	 */
+	if (net_dev->reg_state == NETREG_REGISTERED) {
+		netif_tx_disable(net_dev);
+		netif_carrier_off(net_dev);
+	}
+	return i2400m->bus_reset(i2400m, rt);
+}
+EXPORT_SYMBOL_GPL(i2400m_reset);
+
+
 /**
  * i2400m_setup - bus-generic setup function for the i2400m device
  *
@@ -625,13 +840,9 @@ EXPORT_SYMBOL_GPL(i2400m_dev_reset_handle);
  *
  * Returns: 0 if ok, < 0 errno code on error.
  *
- * Initializes the bus-generic parts of the i2400m driver; the
- * bus-specific parts have been initialized, function pointers filled
- * out by the bus-specific probe function.
- *
- * As well, this registers the WiMAX and net device nodes. Once this
- * function returns, the device is operative and has to be ready to
- * receive and send network traffic and WiMAX control operations.
+ * Sets up basic device comunication infrastructure, boots the ROM to
+ * read the MAC address, registers with the WiMAX and network stacks
+ * and then brings up the device.
  */
 int i2400m_setup(struct i2400m *i2400m, enum i2400m_bri bm_flags)
 {
@@ -645,16 +856,21 @@ int i2400m_setup(struct i2400m *i2400m, enum i2400m_bri bm_flags)
 	snprintf(wimax_dev->name, sizeof(wimax_dev->name),
 		 "i2400m-%s:%s", dev->bus->name, dev_name(dev));
 
-	i2400m->bm_cmd_buf = kzalloc(I2400M_BM_CMD_BUF_SIZE, GFP_KERNEL);
-	if (i2400m->bm_cmd_buf == NULL) {
-		dev_err(dev, "cannot allocate USB command buffer\n");
-		goto error_bm_cmd_kzalloc;
+	result = i2400m_bm_buf_alloc(i2400m);
+	if (result < 0) {
+		dev_err(dev, "cannot allocate bootmode scratch buffers\n");
+		goto error_bm_buf_alloc;
 	}
-	i2400m->bm_ack_buf = kzalloc(I2400M_BM_ACK_BUF_SIZE, GFP_KERNEL);
-	if (i2400m->bm_ack_buf == NULL) {
-		dev_err(dev, "cannot allocate USB ack buffer\n");
-		goto error_bm_ack_buf_kzalloc;
+
+	if (i2400m->bus_setup) {
+		result = i2400m->bus_setup(i2400m);
+		if (result < 0) {
+			dev_err(dev, "bus-specific setup failed: %d\n",
+				result);
+			goto error_bus_setup;
+		}
 	}
+
 	result = i2400m_bootrom_init(i2400m, bm_flags);
 	if (result < 0) {
 		dev_err(dev, "read mac addr: bootrom init "
@@ -666,6 +882,9 @@ int i2400m_setup(struct i2400m *i2400m, enum i2400m_bri bm_flags)
 		goto error_read_mac_addr;
 	random_ether_addr(i2400m->src_mac_addr);
 
+	i2400m->pm_notifier.notifier_call = i2400m_pm_notifier;
+	register_pm_notifier(&i2400m->pm_notifier);
+
 	result = register_netdev(net_dev);	/* Okey dokey, bring it up */
 	if (result < 0) {
 		dev_err(dev, "cannot register i2400m network device: %d\n",
@@ -674,18 +893,13 @@ int i2400m_setup(struct i2400m *i2400m, enum i2400m_bri bm_flags)
 	}
 	netif_carrier_off(net_dev);
 
-	result = i2400m_dev_start(i2400m, bm_flags);
-	if (result < 0)
-		goto error_dev_start;
-
 	i2400m->wimax_dev.op_msg_from_user = i2400m_op_msg_from_user;
 	i2400m->wimax_dev.op_rfkill_sw_toggle = i2400m_op_rfkill_sw_toggle;
 	i2400m->wimax_dev.op_reset = i2400m_op_reset;
+
 	result = wimax_dev_add(&i2400m->wimax_dev, net_dev);
 	if (result < 0)
 		goto error_wimax_dev_add;
-	/* User space needs to do some init stuff */
-	wimax_state_change(wimax_dev, WIMAX_ST_UNINITIALIZED);
 
 	/* Now setup all that requires a registered net and wimax device. */
 	result = sysfs_create_group(&net_dev->dev.kobj, &i2400m_dev_attr_group);
@@ -693,30 +907,37 @@ int i2400m_setup(struct i2400m *i2400m, enum i2400m_bri bm_flags)
 		dev_err(dev, "cannot setup i2400m's sysfs: %d\n", result);
 		goto error_sysfs_setup;
 	}
+
 	result = i2400m_debugfs_add(i2400m);
 	if (result < 0) {
 		dev_err(dev, "cannot setup i2400m's debugfs: %d\n", result);
 		goto error_debugfs_setup;
 	}
+
+	result = i2400m_dev_start(i2400m, bm_flags);
+	if (result < 0)
+		goto error_dev_start;
 	d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
 	return result;
 
+error_dev_start:
+	i2400m_debugfs_rm(i2400m);
 error_debugfs_setup:
 	sysfs_remove_group(&i2400m->wimax_dev.net_dev->dev.kobj,
 			   &i2400m_dev_attr_group);
 error_sysfs_setup:
 	wimax_dev_rm(&i2400m->wimax_dev);
 error_wimax_dev_add:
-	i2400m_dev_stop(i2400m);
-error_dev_start:
 	unregister_netdev(net_dev);
 error_register_netdev:
+	unregister_pm_notifier(&i2400m->pm_notifier);
 error_read_mac_addr:
 error_bootrom_init:
-	kfree(i2400m->bm_ack_buf);
-error_bm_ack_buf_kzalloc:
-	kfree(i2400m->bm_cmd_buf);
-error_bm_cmd_kzalloc:
+	if (i2400m->bus_release)
+		i2400m->bus_release(i2400m);
+error_bus_setup:
+	i2400m_bm_buf_free(i2400m);
+error_bm_buf_alloc:
 	d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
 	return result;
 }
@@ -735,14 +956,17 @@ void i2400m_release(struct i2400m *i2400m)
 	d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
 	netif_stop_queue(i2400m->wimax_dev.net_dev);
 
+	i2400m_dev_stop(i2400m);
+
 	i2400m_debugfs_rm(i2400m);
 	sysfs_remove_group(&i2400m->wimax_dev.net_dev->dev.kobj,
 			   &i2400m_dev_attr_group);
 	wimax_dev_rm(&i2400m->wimax_dev);
-	i2400m_dev_stop(i2400m);
 	unregister_netdev(i2400m->wimax_dev.net_dev);
-	kfree(i2400m->bm_ack_buf);
-	kfree(i2400m->bm_cmd_buf);
+	unregister_pm_notifier(&i2400m->pm_notifier);
+	if (i2400m->bus_release)
+		i2400m->bus_release(i2400m);
+	i2400m_bm_buf_free(i2400m);
 	d_fnend(3, dev, "(i2400m %p) = void\n", i2400m);
 }
 EXPORT_SYMBOL_GPL(i2400m_release);
@@ -759,6 +983,7 @@ struct d_level D_LEVEL[] = {
 	D_SUBMODULE_DEFINE(netdev),
 	D_SUBMODULE_DEFINE(rfkill),
 	D_SUBMODULE_DEFINE(rx),
+	D_SUBMODULE_DEFINE(sysfs),
 	D_SUBMODULE_DEFINE(tx),
 };
 size_t D_LEVEL_SIZE = ARRAY_SIZE(D_LEVEL);
@@ -767,7 +992,9 @@ size_t D_LEVEL_SIZE = ARRAY_SIZE(D_LEVEL);
 static
 int __init i2400m_driver_init(void)
 {
-	return 0;
+	d_parse_params(D_LEVEL, D_LEVEL_SIZE, i2400m_debug_params,
+		       "i2400m.debug");
+	return i2400m_barker_db_init(i2400m_barkers_params);
 }
 module_init(i2400m_driver_init);
 
@@ -776,6 +1003,7 @@ void __exit i2400m_driver_exit(void)
 {
 	/* for scheds i2400m_dev_reset_handle() */
 	flush_scheduled_work();
+	i2400m_barker_db_exit();
 	return;
 }
 module_exit(i2400m_driver_exit);

drivers/net/wimax/i2400m/fw.c

@@ -40,11 +40,9 @@
  *
  * THE PROCEDURE
  *
- * (this is decribed for USB, but for SDIO is similar)
- *
- * The 2400m works in two modes: boot-mode or normal mode. In boot
- * mode we can execute only a handful of commands targeted at
- * uploading the firmware and launching it.
+ * The 2400m and derived devices work in two modes: boot-mode or
+ * normal mode. In boot mode we can execute only a handful of commands
+ * targeted at uploading the firmware and launching it.
  *
  * The 2400m enters boot mode when it is first connected to the
  * system, when it crashes and when you ask it to reboot. There are
@@ -52,18 +50,26 @@
  * firmwares signed with a certain private key, non-signed takes any
  * firmware. Normal hardware takes only signed firmware.
  *
- * Upon entrance to boot mode, the device sends a few zero length
- * packets (ZLPs) on the notification endpoint, then a reboot barker
- * (4 le32 words with value I2400M_{S,N}BOOT_BARKER). We ack it by
- * sending the same barker on the bulk out endpoint. The device acks
- * with a reboot ack barker (4 le32 words with value 0xfeedbabe) and
- * then the device is fully rebooted. At this point we can upload the
- * firmware.
+ * On boot mode, in USB, we write to the device using the bulk out
+ * endpoint and read from it in the notification endpoint. In SDIO we
+ * talk to it via the write address and read from the read address.
+ *
+ * Upon entrance to boot mode, the device sends (preceeded with a few
+ * zero length packets (ZLPs) on the notification endpoint in USB) a
+ * reboot barker (4 le32 words with the same value). We ack it by
+ * sending the same barker to the device. The device acks with a
+ * reboot ack barker (4 le32 words with value I2400M_ACK_BARKER) and
+ * then is fully booted. At this point we can upload the firmware.
+ *
+ * Note that different iterations of the device and EEPROM
+ * configurations will send different [re]boot barkers; these are
+ * collected in i2400m_barker_db along with the firmware
+ * characteristics they require.
  *
  * This process is accomplished by the i2400m_bootrom_init()
  * function. All the device interaction happens through the
  * i2400m_bm_cmd() [boot mode command]. Special return values will
- * indicate if the device resets.
+ * indicate if the device did reset during the process.
  *
  * After this, we read the MAC address and then (if needed)
  * reinitialize the device. We need to read it ahead of time because
@@ -72,11 +78,11 @@
  *
  * We can then upload the firmware file. The file is composed of a BCF
  * header (basic data, keys and signatures) and a list of write
- * commands and payloads. We first upload the header
- * [i2400m_dnload_init()] and then pass the commands and payloads
- * verbatim to the i2400m_bm_cmd() function
- * [i2400m_dnload_bcf()]. Then we tell the device to jump to the new
- * firmware [i2400m_dnload_finalize()].
+ * commands and payloads. Optionally more BCF headers might follow the
+ * main payload. We first upload the header [i2400m_dnload_init()] and
+ * then pass the commands and payloads verbatim to the i2400m_bm_cmd()
+ * function [i2400m_dnload_bcf()]. Then we tell the device to jump to
+ * the new firmware [i2400m_dnload_finalize()].
  *
  * Once firmware is uploaded, we are good to go :)
  *
@@ -99,18 +105,32 @@
  * read an acknolwedgement from it (or an asynchronous notification)
  * from it.
  *
+ * FIRMWARE LOADING
+ *
+ * Note that in some cases, we can't just load a firmware file (for
+ * example, when resuming). For that, we might cache the firmware
+ * file. Thus, when doing the bootstrap, if there is a cache firmware
+ * file, it is used; if not, loading from disk is attempted.
+ *
  * ROADMAP
  *
+ * i2400m_barker_db_init              Called by i2400m_driver_init()
+ *   i2400m_barker_db_add
+ *
+ * i2400m_barker_db_exit              Called by i2400m_driver_exit()
+ *
  * i2400m_dev_bootstrap               Called by __i2400m_dev_start()
  *   request_firmware
- *   i2400m_fw_check
- *   i2400m_fw_dnload
+ *   i2400m_fw_bootstrap
+ *     i2400m_fw_check
+ *       i2400m_fw_hdr_check
+ *     i2400m_fw_dnload
  *   release_firmware
  *
  * i2400m_fw_dnload
  *   i2400m_bootrom_init
  *     i2400m_bm_cmd
- *     i2400m->bus_reset
+ *     i2400m_reset
  *   i2400m_dnload_init
  *     i2400m_dnload_init_signed
  *     i2400m_dnload_init_nonsigned
@@ -125,9 +145,14 @@
  *   i2400m->bus_bm_cmd_send()
  *   i2400m->bus_bm_wait_for_ack
  *   __i2400m_bm_ack_verify
+ *     i2400m_is_boot_barker
  *
  * i2400m_bm_cmd_prepare              Used by bus-drivers to prep
  *                                    commands before sending
+ *
+ * i2400m_pm_notifier                 Called on Power Management events
+ *   i2400m_fw_cache
+ *   i2400m_fw_uncache
  */
 #include <linux/firmware.h>
 #include <linux/sched.h>
@@ -174,6 +199,240 @@ void i2400m_bm_cmd_prepare(struct i2400m_bootrom_header *cmd)
 EXPORT_SYMBOL_GPL(i2400m_bm_cmd_prepare);
 
 
+/*
+ * Database of known barkers.
+ *
+ * A barker is what the device sends indicating he is ready to be
+ * bootloaded. Different versions of the device will send different
+ * barkers. Depending on the barker, it might mean the device wants
+ * some kind of firmware or the other.
+ */
+static struct i2400m_barker_db {
+	__le32 data[4];
+} *i2400m_barker_db;
+static size_t i2400m_barker_db_used, i2400m_barker_db_size;
+
+
+static
+int i2400m_zrealloc_2x(void **ptr, size_t *_count, size_t el_size,
+		       gfp_t gfp_flags)
+{
+	size_t old_count = *_count,
+		new_count = old_count ? 2 * old_count : 2,
+		old_size = el_size * old_count,
+		new_size = el_size * new_count;
+	void *nptr = krealloc(*ptr, new_size, gfp_flags);
+	if (nptr) {
+		/* zero the other half or the whole thing if old_count
+		 * was zero */
+		if (old_size == 0)
+			memset(nptr, 0, new_size);
+		else
+			memset(nptr + old_size, 0, old_size);
+		*_count = new_count;
+		*ptr = nptr;
+		return 0;
+	} else
+		return -ENOMEM;
+}
+
+
+/*
+ * Add a barker to the database
+ *
+ * This cannot used outside of this module and only at at module_init
+ * time. This is to avoid the need to do locking.
+ */
+static
+int i2400m_barker_db_add(u32 barker_id)
+{
+	int result;
+
+	struct i2400m_barker_db *barker;
+	if (i2400m_barker_db_used >= i2400m_barker_db_size) {
+		result = i2400m_zrealloc_2x(
+			(void **) &i2400m_barker_db, &i2400m_barker_db_size,
+			sizeof(i2400m_barker_db[0]), GFP_KERNEL);
+		if (result < 0)
+			return result;
+	}
+	barker = i2400m_barker_db + i2400m_barker_db_used++;
+	barker->data[0] = le32_to_cpu(barker_id);
+	barker->data[1] = le32_to_cpu(barker_id);
+	barker->data[2] = le32_to_cpu(barker_id);
+	barker->data[3] = le32_to_cpu(barker_id);
+	return 0;
+}
+
+
+void i2400m_barker_db_exit(void)
+{
+	kfree(i2400m_barker_db);
+	i2400m_barker_db = NULL;
+	i2400m_barker_db_size = 0;
+	i2400m_barker_db_used = 0;
+}
+
+
+/*
+ * Helper function to add all the known stable barkers to the barker
+ * database.
+ */
+static
+int i2400m_barker_db_known_barkers(void)
+{
+	int result;
+
+	result = i2400m_barker_db_add(I2400M_NBOOT_BARKER);
+	if (result < 0)
+		goto error_add;
+	result = i2400m_barker_db_add(I2400M_SBOOT_BARKER);
+	if (result < 0)
+		goto error_add;
+	result = i2400m_barker_db_add(I2400M_SBOOT_BARKER_6050);
+	if (result < 0)
+		goto error_add;
+error_add:
+       return result;
+}
+
+
+/*
+ * Initialize the barker database
+ *
+ * This can only be used from the module_init function for this
+ * module; this is to avoid the need to do locking.
+ *
+ * @options: command line argument with extra barkers to
+ *     recognize. This is a comma-separated list of 32-bit hex
+ *     numbers. They are appended to the existing list. Setting 0
+ *     cleans the existing list and starts a new one.
+ */
+int i2400m_barker_db_init(const char *_options)
+{
+	int result;
+	char *options = NULL, *options_orig, *token;
+
+	i2400m_barker_db = NULL;
+	i2400m_barker_db_size = 0;
+	i2400m_barker_db_used = 0;
+
+	result = i2400m_barker_db_known_barkers();
+	if (result < 0)
+		goto error_add;
+	/* parse command line options from i2400m.barkers */
+	if (_options != NULL) {
+		unsigned barker;
+
+		options_orig = kstrdup(_options, GFP_KERNEL);
+		if (options_orig == NULL)
+			goto error_parse;
+		options = options_orig;
+
+		while ((token = strsep(&options, ",")) != NULL) {
+			if (*token == '\0')	/* eat joint commas */
+				continue;
+			if (sscanf(token, "%x", &barker) != 1
+			    || barker > 0xffffffff) {
+				printk(KERN_ERR "%s: can't recognize "
+				       "i2400m.barkers value '%s' as "
+				       "a 32-bit number\n",
+				       __func__, token);
+				result = -EINVAL;
+				goto error_parse;
+			}
+			if (barker == 0) {
+				/* clean list and start new */
+				i2400m_barker_db_exit();
+				continue;
+			}
+			result = i2400m_barker_db_add(barker);
+			if (result < 0)
+				goto error_add;
+		}
+		kfree(options_orig);
+	}
+	return 0;
+
+error_parse:
+error_add:
+	kfree(i2400m_barker_db);
+	return result;
+}
+
+
+/*
+ * Recognize a boot barker
+ *
+ * @buf: buffer where the boot barker.
+ * @buf_size: size of the buffer (has to be 16 bytes). It is passed
+ *     here so the function can check it for the caller.
+ *
+ * Note that as a side effect, upon identifying the obtained boot
+ * barker, this function will set i2400m->barker to point to the right
+ * barker database entry. Subsequent calls to the function will result
+ * in verifying that the same type of boot barker is returned when the
+ * device [re]boots (as long as the same device instance is used).
+ *
+ * Return: 0 if @buf matches a known boot barker. -ENOENT if the
+ *     buffer in @buf doesn't match any boot barker in the database or
+ *     -EILSEQ if the buffer doesn't have the right size.
+ */
+int i2400m_is_boot_barker(struct i2400m *i2400m,
+			  const void *buf, size_t buf_size)
+{
+	int result;
+	struct device *dev = i2400m_dev(i2400m);
+	struct i2400m_barker_db *barker;
+	int i;
+
+	result = -ENOENT;
+	if (buf_size != sizeof(i2400m_barker_db[i].data))
+		return result;
+
+	/* Short circuit if we have already discovered the barker
+	 * associated with the device. */
+	if (i2400m->barker
+	    && !memcmp(buf, i2400m->barker, sizeof(i2400m->barker->data))) {
+		unsigned index = (i2400m->barker - i2400m_barker_db)
+			/ sizeof(*i2400m->barker);
+		d_printf(2, dev, "boot barker cache-confirmed #%u/%08x\n",
+			 index, le32_to_cpu(i2400m->barker->data[0]));
+		return 0;
+	}
+
+	for (i = 0; i < i2400m_barker_db_used; i++) {
+		barker = &i2400m_barker_db[i];
+		BUILD_BUG_ON(sizeof(barker->data) != 16);
+		if (memcmp(buf, barker->data, sizeof(barker->data)))
+			continue;
+
+		if (i2400m->barker == NULL) {
+			i2400m->barker = barker;
+			d_printf(1, dev, "boot barker set to #%u/%08x\n",
+				 i, le32_to_cpu(barker->data[0]));
+			if (barker->data[0] == le32_to_cpu(I2400M_NBOOT_BARKER))
+				i2400m->sboot = 0;
+			else
+				i2400m->sboot = 1;
+		} else if (i2400m->barker != barker) {
+			dev_err(dev, "HW inconsistency: device "
+				"reports a different boot barker "
+				"than set (from %08x to %08x)\n",
+				le32_to_cpu(i2400m->barker->data[0]),
+				le32_to_cpu(barker->data[0]));
+			result = -EIO;
+		} else
+			d_printf(2, dev, "boot barker confirmed #%u/%08x\n",
+				 i, le32_to_cpu(barker->data[0]));
+		result = 0;
+		break;
+	}
+	return result;
+}
+EXPORT_SYMBOL_GPL(i2400m_is_boot_barker);
+
+
 /*
  * Verify the ack data received
  *
@@ -204,20 +463,10 @@ ssize_t __i2400m_bm_ack_verify(struct i2400m *i2400m, int opcode,
 			opcode, ack_size, sizeof(*ack));
 		goto error_ack_short;
 	}
-	if (ack_size == sizeof(i2400m_NBOOT_BARKER)
-		 && memcmp(ack, i2400m_NBOOT_BARKER, sizeof(*ack)) == 0) {
+	result = i2400m_is_boot_barker(i2400m, ack, ack_size);
+	if (result >= 0) {
 		result = -ERESTARTSYS;
-		i2400m->sboot = 0;
-		d_printf(6, dev, "boot-mode cmd %d: "
-			 "HW non-signed boot barker\n", opcode);
-		goto error_reboot;
-	}
-	if (ack_size == sizeof(i2400m_SBOOT_BARKER)
-		 && memcmp(ack, i2400m_SBOOT_BARKER, sizeof(*ack)) == 0) {
-		result = -ERESTARTSYS;
-		i2400m->sboot = 1;
-		d_printf(6, dev, "boot-mode cmd %d: HW signed reboot barker\n",
-			 opcode);
+		d_printf(6, dev, "boot-mode cmd %d: HW boot barker\n", opcode);
 		goto error_reboot;
 	}
 	if (ack_size == sizeof(i2400m_ACK_BARKER)
@@ -343,7 +592,6 @@ ssize_t i2400m_bm_cmd(struct i2400m *i2400m,
 	BUG_ON(i2400m->boot_mode == 0);
 
 	if (cmd != NULL) {		/* send the command */
-		memcpy(i2400m->bm_cmd_buf, cmd, cmd_size);
 		result = i2400m->bus_bm_cmd_send(i2400m, cmd, cmd_size, flags);
 		if (result < 0)
 			goto error_cmd_send;
@@ -432,8 +680,8 @@ static int i2400m_download_chunk(struct i2400m *i2400m, const void *chunk,
  * Download a BCF file's sections to the device
  *
  * @i2400m: device descriptor
- * @bcf: pointer to firmware data (followed by the payloads). Assumed
- *       verified and consistent.
+ * @bcf: pointer to firmware data (first header followed by the
+ *     payloads). Assumed verified and consistent.
  * @bcf_len: length (in bytes) of the @bcf buffer.
  *
  * Returns: < 0 errno code on error or the offset to the jump instruction.
@@ -472,14 +720,17 @@ ssize_t i2400m_dnload_bcf(struct i2400m *i2400m,
 			 "downloading section #%zu (@%zu %zu B) to 0x%08x\n",
 			 section, offset, sizeof(*bh) + data_size,
 			 le32_to_cpu(bh->target_addr));
-		if (i2400m_brh_get_opcode(bh) == I2400M_BRH_SIGNED_JUMP) {
-			/* Secure boot needs to stop here */
-			d_printf(5, dev,  "signed jump found @%zu\n", offset);
+		/*
+		 * We look for JUMP cmd from the bootmode header,
+		 * either I2400M_BRH_SIGNED_JUMP for secure boot
+		 * or I2400M_BRH_JUMP for unsecure boot, the last chunk
+		 * should be the bootmode header with JUMP cmd.
+		 */
+		if (i2400m_brh_get_opcode(bh) == I2400M_BRH_SIGNED_JUMP ||
+			i2400m_brh_get_opcode(bh) == I2400M_BRH_JUMP) {
+			d_printf(5, dev,  "jump found @%zu\n", offset);
 			break;
 		}
-		if (offset + section_size == bcf_len)
-			/* Non-secure boot stops here */
-			break;
 		if (offset + section_size > bcf_len) {
 			dev_err(dev, "fw %s: bad section #%zu, "
 				"end (@%zu) beyond EOF (@%zu)\n",
@@ -509,14 +760,31 @@ ssize_t i2400m_dnload_bcf(struct i2400m *i2400m,
 }
 
 
+/*
+ * Indicate if the device emitted a reboot barker that indicates
+ * "signed boot"
+ */
+static
+unsigned i2400m_boot_is_signed(struct i2400m *i2400m)
+{
+	return likely(i2400m->sboot);
+}
+
+
 /*
  * Do the final steps of uploading firmware
  *
+ * @bcf_hdr: BCF header we are actually using
+ * @bcf: pointer to the firmware image (which matches the first header
+ *     that is followed by the actual payloads).
+ * @offset: [byte] offset into @bcf for the command we need to send.
+ *
  * Depending on the boot mode (signed vs non-signed), different
  * actions need to be taken.
  */
 static
 int i2400m_dnload_finalize(struct i2400m *i2400m,
+			   const struct i2400m_bcf_hdr *bcf_hdr,
 			   const struct i2400m_bcf_hdr *bcf, size_t offset)
 {
 	int ret = 0;
@@ -530,10 +798,14 @@ int i2400m_dnload_finalize(struct i2400m *i2400m,
 
 	d_fnstart(3, dev, "offset %zu\n", offset);
 	cmd = (void *) bcf + offset;
-	if (i2400m->sboot == 0) {
+	if (i2400m_boot_is_signed(i2400m) == 0) {
 		struct i2400m_bootrom_header jump_ack;
 		d_printf(1, dev, "unsecure boot, jumping to 0x%08x\n",
 			le32_to_cpu(cmd->target_addr));
+		cmd_buf = i2400m->bm_cmd_buf;
+		memcpy(&cmd_buf->cmd, cmd, sizeof(*cmd));
+		cmd = &cmd_buf->cmd;
+		/* now cmd points to the actual bootrom_header in cmd_buf */
 		i2400m_brh_set_opcode(cmd, I2400M_BRH_JUMP);
 		cmd->data_size = 0;
 		ret = i2400m_bm_cmd(i2400m, cmd, sizeof(*cmd),
@@ -544,12 +816,13 @@ int i2400m_dnload_finalize(struct i2400m *i2400m,
 		cmd_buf = i2400m->bm_cmd_buf;
 		memcpy(&cmd_buf->cmd, cmd, sizeof(*cmd));
 		signature_block_offset =
-			sizeof(*bcf)
-			+ le32_to_cpu(bcf->key_size) * sizeof(u32)
-			+ le32_to_cpu(bcf->exponent_size) * sizeof(u32);
+			sizeof(*bcf_hdr)
+			+ le32_to_cpu(bcf_hdr->key_size) * sizeof(u32)
+			+ le32_to_cpu(bcf_hdr->exponent_size) * sizeof(u32);
 		signature_block_size =
-			le32_to_cpu(bcf->modulus_size) * sizeof(u32);
-		memcpy(cmd_buf->cmd_pl, (void *) bcf + signature_block_offset,
+			le32_to_cpu(bcf_hdr->modulus_size) * sizeof(u32);
+		memcpy(cmd_buf->cmd_pl,
+		       (void *) bcf_hdr + signature_block_offset,
 		       signature_block_size);
 		ret = i2400m_bm_cmd(i2400m, &cmd_buf->cmd,
 				    sizeof(cmd_buf->cmd) + signature_block_size,
@@ -565,7 +838,7 @@ int i2400m_dnload_finalize(struct i2400m *i2400m,
  *
  * @i2400m: device descriptor
  * @flags:
- *      I2400M_BRI_SOFT: a reboot notification has been seen
+ *      I2400M_BRI_SOFT: a reboot barker has been seen
  *          already, so don't wait for it.
  *
  *      I2400M_BRI_NO_REBOOT: Don't send a reboot command, but wait
@@ -576,17 +849,15 @@ int i2400m_dnload_finalize(struct i2400m *i2400m,
  *
  *     < 0 errno code on error, 0 if ok.
  *
- *     i2400m->sboot set to 0 for unsecure boot process, 1 for secure
- *     boot process.
- *
  * Description:
  *
  * Tries hard enough to put the device in boot-mode. There are two
  * main phases to this:
  *
  * a. (1) send a reboot command and (2) get a reboot barker
- * b. (1) ack the reboot sending a reboot barker and (2) getting an
- *        ack barker in return
+ *
+ * b. (1) echo/ack the reboot sending the reboot barker back and (2)
+ *        getting an ack barker in return
  *
  * We want to skip (a) in some cases [soft]. The state machine is
  * horrible, but it is basically: on each phase, send what has to be
@@ -594,6 +865,16 @@ int i2400m_dnload_finalize(struct i2400m *i2400m,
  * have to backtrack and retry, so we keep a max tries counter for
  * that.
  *
+ * It sucks because we don't know ahead of time which is going to be
+ * the reboot barker (the device might send different ones depending
+ * on its EEPROM config) and once the device reboots and waits for the
+ * echo/ack reboot barker being sent back, it doesn't understand
+ * anything else. So we can be left at the point where we don't know
+ * what to send to it -- cold reset and bus reset seem to have little
+ * effect. So the function iterates (in this case) through all the
+ * known barkers and tries them all until an ACK is
+ * received. Otherwise, it gives up.
+ *
  * If we get a timeout after sending a warm reset, we do it again.
  */
 int i2400m_bootrom_init(struct i2400m *i2400m, enum i2400m_bri flags)
@@ -602,10 +883,11 @@ int i2400m_bootrom_init(struct i2400m *i2400m, enum i2400m_bri flags)
 	struct device *dev = i2400m_dev(i2400m);
 	struct i2400m_bootrom_header *cmd;
 	struct i2400m_bootrom_header ack;
-	int count = I2400M_BOOT_RETRIES;
+	int count = i2400m->bus_bm_retries;
 	int ack_timeout_cnt = 1;
+	unsigned i;
 
-	BUILD_BUG_ON(sizeof(*cmd) != sizeof(i2400m_NBOOT_BARKER));
+	BUILD_BUG_ON(sizeof(*cmd) != sizeof(i2400m_barker_db[0].data));
 	BUILD_BUG_ON(sizeof(ack) != sizeof(i2400m_ACK_BARKER));
 
 	d_fnstart(4, dev, "(i2400m %p flags 0x%08x)\n", i2400m, flags);
@@ -614,27 +896,59 @@ int i2400m_bootrom_init(struct i2400m *i2400m, enum i2400m_bri flags)
 	if (flags & I2400M_BRI_SOFT)
 		goto do_reboot_ack;
 do_reboot:
+	ack_timeout_cnt = 1;
 	if (--count < 0)
 		goto error_timeout;
 	d_printf(4, dev, "device reboot: reboot command [%d # left]\n",
 		 count);
 	if ((flags & I2400M_BRI_NO_REBOOT) == 0)
-		i2400m->bus_reset(i2400m, I2400M_RT_WARM);
+		i2400m_reset(i2400m, I2400M_RT_WARM);
 	result = i2400m_bm_cmd(i2400m, NULL, 0, &ack, sizeof(ack),
 			       I2400M_BM_CMD_RAW);
 	flags &= ~I2400M_BRI_NO_REBOOT;
 	switch (result) {
 	case -ERESTARTSYS:
+		/*
+		 * at this point, i2400m_bm_cmd(), through
+		 * __i2400m_bm_ack_process(), has updated
+		 * i2400m->barker and we are good to go.
+		 */
 		d_printf(4, dev, "device reboot: got reboot barker\n");
 		break;
 	case -EISCONN:	/* we don't know how it got here...but we follow it */
 		d_printf(4, dev, "device reboot: got ack barker - whatever\n");
 		goto do_reboot;
-	case -ETIMEDOUT:	/* device has timed out, we might be in boot
-				 * mode already and expecting an ack, let's try
-				 * that */
-		dev_info(dev, "warm reset timed out, trying an ack\n");
-		goto do_reboot_ack;
+	case -ETIMEDOUT:
+		/*
+		 * Device has timed out, we might be in boot mode
+		 * already and expecting an ack; if we don't know what
+		 * the barker is, we just send them all. Cold reset
+		 * and bus reset don't work. Beats me.
+		 */
+		if (i2400m->barker != NULL) {
+			dev_err(dev, "device boot: reboot barker timed out, "
+				"trying (set) %08x echo/ack\n",
+				le32_to_cpu(i2400m->barker->data[0]));
+			goto do_reboot_ack;
+		}
+		for (i = 0; i < i2400m_barker_db_used; i++) {
+			struct i2400m_barker_db *barker = &i2400m_barker_db[i];
+			memcpy(cmd, barker->data, sizeof(barker->data));
+			result = i2400m_bm_cmd(i2400m, cmd, sizeof(*cmd),
+					       &ack, sizeof(ack),
+					       I2400M_BM_CMD_RAW);
+			if (result == -EISCONN) {
+				dev_warn(dev, "device boot: got ack barker "
+					 "after sending echo/ack barker "
+					 "#%d/%08x; rebooting j.i.c.\n",
+					 i, le32_to_cpu(barker->data[0]));
+				flags &= ~I2400M_BRI_NO_REBOOT;
+				goto do_reboot;
+			}
+		}
+		dev_err(dev, "device boot: tried all the echo/acks, could "
+			"not get device to respond; giving up");
+		result = -ESHUTDOWN;
 	case -EPROTO:
 	case -ESHUTDOWN:	/* dev is gone */
 	case -EINTR:		/* user cancelled */
@@ -642,6 +956,7 @@ int i2400m_bootrom_init(struct i2400m *i2400m, enum i2400m_bri flags)
 	default:
 		dev_err(dev, "device reboot: error %d while waiting "
 			"for reboot barker - rebooting\n", result);
+		d_dump(1, dev, &ack, result);
 		goto do_reboot;
 	}
 	/* At this point we ack back with 4 REBOOT barkers and expect
@@ -650,12 +965,7 @@ int i2400m_bootrom_init(struct i2400m *i2400m, enum i2400m_bri flags)
 	 * notification and report it as -EISCONN. */
 do_reboot_ack:
 	d_printf(4, dev, "device reboot ack: sending ack [%d # left]\n", count);
-	if (i2400m->sboot == 0)
-		memcpy(cmd, i2400m_NBOOT_BARKER,
-		       sizeof(i2400m_NBOOT_BARKER));
-	else
-		memcpy(cmd, i2400m_SBOOT_BARKER,
-		       sizeof(i2400m_SBOOT_BARKER));
+	memcpy(cmd, i2400m->barker->data, sizeof(i2400m->barker->data));
 	result = i2400m_bm_cmd(i2400m, cmd, sizeof(*cmd),
 			       &ack, sizeof(ack), I2400M_BM_CMD_RAW);
 	switch (result) {
@@ -668,10 +978,8 @@ int i2400m_bootrom_init(struct i2400m *i2400m, enum i2400m_bri flags)
 		d_printf(4, dev, "reboot ack: got ack barker - good\n");
 		break;
 	case -ETIMEDOUT:	/* no response, maybe it is the other type? */
-		if (ack_timeout_cnt-- >= 0) {
-			d_printf(4, dev, "reboot ack timedout: "
-				 "trying the other type?\n");
-			i2400m->sboot = !i2400m->sboot;
+		if (ack_timeout_cnt-- < 0) {
+			d_printf(4, dev, "reboot ack timedout: retrying\n");
 			goto do_reboot_ack;
 		} else {
 			dev_err(dev, "reboot ack timedout too long: "
@@ -839,32 +1147,29 @@ int i2400m_dnload_init_signed(struct i2400m *i2400m,
  * (signed or non-signed).
  */
 static
-int i2400m_dnload_init(struct i2400m *i2400m, const struct i2400m_bcf_hdr *bcf)
+int i2400m_dnload_init(struct i2400m *i2400m,
+		       const struct i2400m_bcf_hdr *bcf_hdr)
 {
 	int result;
 	struct device *dev = i2400m_dev(i2400m);
-	u32 module_id = le32_to_cpu(bcf->module_id);
 
-	if (i2400m->sboot == 0
-	    && (module_id & I2400M_BCF_MOD_ID_POKES) == 0) {
-		/* non-signed boot process without pokes */
-		result = i2400m_dnload_init_nonsigned(i2400m);
+	if (i2400m_boot_is_signed(i2400m)) {
+		d_printf(1, dev, "signed boot\n");
+		result = i2400m_dnload_init_signed(i2400m, bcf_hdr);
 		if (result == -ERESTARTSYS)
 			return result;
 		if (result < 0)
-			dev_err(dev, "fw %s: non-signed download "
+			dev_err(dev, "firmware %s: signed boot download "
 				"initialization failed: %d\n",
 				i2400m->fw_name, result);
-	} else if (i2400m->sboot == 0
-		 && (module_id & I2400M_BCF_MOD_ID_POKES)) {
-		/* non-signed boot process with pokes, nothing to do */
-		result = 0;
-	} else {		 /* signed boot process */
-		result = i2400m_dnload_init_signed(i2400m, bcf);
+	} else {
+		/* non-signed boot process without pokes */
+		d_printf(1, dev, "non-signed boot\n");
+		result = i2400m_dnload_init_nonsigned(i2400m);
 		if (result == -ERESTARTSYS)
 			return result;
 		if (result < 0)
-			dev_err(dev, "fw %s: signed boot download "
+			dev_err(dev, "firmware %s: non-signed download "
 				"initialization failed: %d\n",
 				i2400m->fw_name, result);
 	}
@@ -873,73 +1178,200 @@ int i2400m_dnload_init(struct i2400m *i2400m, const struct i2400m_bcf_hdr *bcf)
 
 
 /*
- * Run quick consistency tests on the firmware file
+ * Run consistency tests on the firmware file and load up headers
  *
  * Check for the firmware being made for the i2400m device,
  * etc...These checks are mostly informative, as the device will make
  * them too; but the driver's response is more informative on what
  * went wrong.
+ *
+ * This will also look at all the headers present on the firmware
+ * file, and update i2400m->fw_bcf_hdr to point to them.
  */
 static
-int i2400m_fw_check(struct i2400m *i2400m,
-		    const struct i2400m_bcf_hdr *bcf,
-		    size_t bcf_size)
+int i2400m_fw_hdr_check(struct i2400m *i2400m,
+			const struct i2400m_bcf_hdr *bcf_hdr,
+			size_t index, size_t offset)
 {
-	int result;
 	struct device *dev = i2400m_dev(i2400m);
+
 	unsigned module_type, header_len, major_version, minor_version,
 		module_id, module_vendor, date, size;
 
-	/* Check hard errors */
-	result = -EINVAL;
-	if (bcf_size < sizeof(*bcf)) {	/* big enough header? */
-		dev_err(dev, "firmware %s too short: "
-			"%zu B vs %zu (at least) expected\n",
-			i2400m->fw_name, bcf_size, sizeof(*bcf));
-		goto error;
-	}
+	module_type = bcf_hdr->module_type;
+	header_len = sizeof(u32) * le32_to_cpu(bcf_hdr->header_len);
+	major_version = (le32_to_cpu(bcf_hdr->header_version) & 0xffff0000)
+		>> 16;
+	minor_version = le32_to_cpu(bcf_hdr->header_version) & 0x0000ffff;
+	module_id = le32_to_cpu(bcf_hdr->module_id);
+	module_vendor = le32_to_cpu(bcf_hdr->module_vendor);
+	date = le32_to_cpu(bcf_hdr->date);
+	size = sizeof(u32) * le32_to_cpu(bcf_hdr->size);
 
-	module_type = bcf->module_type;
-	header_len = sizeof(u32) * le32_to_cpu(bcf->header_len);
-	major_version = le32_to_cpu(bcf->header_version) & 0xffff0000 >> 16;
-	minor_version = le32_to_cpu(bcf->header_version) & 0x0000ffff;
-	module_id = le32_to_cpu(bcf->module_id);
-	module_vendor = le32_to_cpu(bcf->module_vendor);
-	date = le32_to_cpu(bcf->date);
-	size = sizeof(u32) * le32_to_cpu(bcf->size);
-
-	if (bcf_size != size) {		/* annoyingly paranoid */
-		dev_err(dev, "firmware %s: bad size, got "
-			"%zu B vs %u expected\n",
-			i2400m->fw_name, bcf_size, size);
-		goto error;
-	}
+	d_printf(1, dev, "firmware %s #%zd@%08zx: BCF header "
+		 "type:vendor:id 0x%x:%x:%x v%u.%u (%u/%u B) built %08x\n",
+		 i2400m->fw_name, index, offset,
+		 module_type, module_vendor, module_id,
+		 major_version, minor_version, header_len, size, date);
 
-	d_printf(2, dev, "type 0x%x id 0x%x vendor 0x%x; header v%u.%u (%zu B) "
-		 "date %08x (%zu B)\n",
-		 module_type, module_id, module_vendor,
-		 major_version, minor_version, (size_t) header_len,
-		 date, (size_t) size);
+	/* Hard errors */
+	if (major_version != 1) {
+		dev_err(dev, "firmware %s #%zd@%08zx: major header version "
+			"v%u.%u not supported\n",
+			i2400m->fw_name, index, offset,
+			major_version, minor_version);
+		return -EBADF;
+	}
 
 	if (module_type != 6) {		/* built for the right hardware? */
-		dev_err(dev, "bad fw %s: unexpected module type 0x%x; "
-			"aborting\n", i2400m->fw_name, module_type);
-		goto error;
+		dev_err(dev, "firmware %s #%zd@%08zx: unexpected module "
+			"type 0x%x; aborting\n",
+			i2400m->fw_name, index, offset,
+			module_type);
+		return -EBADF;
+	}
+
+	if (module_vendor != 0x8086) {
+		dev_err(dev, "firmware %s #%zd@%08zx: unexpected module "
+			"vendor 0x%x; aborting\n",
+			i2400m->fw_name, index, offset, module_vendor);
+		return -EBADF;
 	}
 
-	/* Check soft-er errors */
-	result = 0;
-	if (module_vendor != 0x8086)
-		dev_err(dev, "bad fw %s? unexpected vendor 0x%04x\n",
-			i2400m->fw_name, module_vendor);
 	if (date < 0x20080300)
-		dev_err(dev, "bad fw %s? build date too old %08x\n",
-			i2400m->fw_name, date);
-error:
+		dev_warn(dev, "firmware %s #%zd@%08zx: build date %08x "
+			 "too old; unsupported\n",
+			 i2400m->fw_name, index, offset, date);
+	return 0;
+}
+
+
+/*
+ * Run consistency tests on the firmware file and load up headers
+ *
+ * Check for the firmware being made for the i2400m device,
+ * etc...These checks are mostly informative, as the device will make
+ * them too; but the driver's response is more informative on what
+ * went wrong.
+ *
+ * This will also look at all the headers present on the firmware
+ * file, and update i2400m->fw_hdrs to point to them.
+ */
+static
+int i2400m_fw_check(struct i2400m *i2400m, const void *bcf, size_t bcf_size)
+{
+	int result;
+	struct device *dev = i2400m_dev(i2400m);
+	size_t headers = 0;
+	const struct i2400m_bcf_hdr *bcf_hdr;
+	const void *itr, *next, *top;
+	size_t slots = 0, used_slots = 0;
+
+	for (itr = bcf, top = itr + bcf_size;
+	     itr < top;
+	     headers++, itr = next) {
+		size_t leftover, offset, header_len, size;
+
+		leftover = top - itr;
+		offset = itr - (const void *) bcf;
+		if (leftover <= sizeof(*bcf_hdr)) {
+			dev_err(dev, "firmware %s: %zu B left at @%zx, "
+				"not enough for BCF header\n",
+				i2400m->fw_name, leftover, offset);
+			break;
+		}
+		bcf_hdr = itr;
+		/* Only the first header is supposed to be followed by
+		 * payload */
+		header_len = sizeof(u32) * le32_to_cpu(bcf_hdr->header_len);
+		size = sizeof(u32) * le32_to_cpu(bcf_hdr->size);
+		if (headers == 0)
+			next = itr + size;
+		else
+			next = itr + header_len;
+
+		result = i2400m_fw_hdr_check(i2400m, bcf_hdr, headers, offset);
+		if (result < 0)
+			continue;
+		if (used_slots + 1 >= slots) {
+			/* +1 -> we need to account for the one we'll
+			 * occupy and at least an extra one for
+			 * always being NULL */
+			result = i2400m_zrealloc_2x(
+				(void **) &i2400m->fw_hdrs, &slots,
+				sizeof(i2400m->fw_hdrs[0]),
+				GFP_KERNEL);
+			if (result < 0)
+				goto error_zrealloc;
+		}
+		i2400m->fw_hdrs[used_slots] = bcf_hdr;
+		used_slots++;
+	}
+	if (headers == 0) {
+		dev_err(dev, "firmware %s: no usable headers found\n",
+			i2400m->fw_name);
+		result = -EBADF;
+	} else
+		result = 0;
+error_zrealloc:
 	return result;
 }
 
 
+/*
+ * Match a barker to a BCF header module ID
+ *
+ * The device sends a barker which tells the firmware loader which
+ * header in the BCF file has to be used. This does the matching.
+ */
+static
+unsigned i2400m_bcf_hdr_match(struct i2400m *i2400m,
+			      const struct i2400m_bcf_hdr *bcf_hdr)
+{
+	u32 barker = le32_to_cpu(i2400m->barker->data[0])
+		& 0x7fffffff;
+	u32 module_id = le32_to_cpu(bcf_hdr->module_id)
+		& 0x7fffffff;	/* high bit used for something else */
+
+	/* special case for 5x50 */
+	if (barker == I2400M_SBOOT_BARKER && module_id == 0)
+		return 1;
+	if (module_id == barker)
+		return 1;
+	return 0;
+}
+
+static
+const struct i2400m_bcf_hdr *i2400m_bcf_hdr_find(struct i2400m *i2400m)
+{
+	struct device *dev = i2400m_dev(i2400m);
+	const struct i2400m_bcf_hdr **bcf_itr, *bcf_hdr;
+	unsigned i = 0;
+	u32 barker = le32_to_cpu(i2400m->barker->data[0]);
+
+	d_printf(2, dev, "finding BCF header for barker %08x\n", barker);
+	if (barker == I2400M_NBOOT_BARKER) {
+		bcf_hdr = i2400m->fw_hdrs[0];
+		d_printf(1, dev, "using BCF header #%u/%08x for non-signed "
+			 "barker\n", 0, le32_to_cpu(bcf_hdr->module_id));
+		return bcf_hdr;
+	}
+	for (bcf_itr = i2400m->fw_hdrs; *bcf_itr != NULL; bcf_itr++, i++) {
+		bcf_hdr = *bcf_itr;
+		if (i2400m_bcf_hdr_match(i2400m, bcf_hdr)) {
+			d_printf(1, dev, "hit on BCF hdr #%u/%08x\n",
+				 i, le32_to_cpu(bcf_hdr->module_id));
+			return bcf_hdr;
+		} else
+			d_printf(1, dev, "miss on BCF hdr #%u/%08x\n",
+				 i, le32_to_cpu(bcf_hdr->module_id));
+	}
+	dev_err(dev, "cannot find a matching BCF header for barker %08x\n",
+		barker);
+	return NULL;
+}
+
+
 /*
  * Download the firmware to the device
  *
@@ -956,14 +1388,16 @@ int i2400m_fw_check(struct i2400m *i2400m,
  */
 static
 int i2400m_fw_dnload(struct i2400m *i2400m, const struct i2400m_bcf_hdr *bcf,
-		     size_t bcf_size, enum i2400m_bri flags)
+		     size_t fw_size, enum i2400m_bri flags)
 {
 	int ret = 0;
 	struct device *dev = i2400m_dev(i2400m);
 	int count = i2400m->bus_bm_retries;
+	const struct i2400m_bcf_hdr *bcf_hdr;
+	size_t bcf_size;
 
-	d_fnstart(5, dev, "(i2400m %p bcf %p size %zu)\n",
-		  i2400m, bcf, bcf_size);
+	d_fnstart(5, dev, "(i2400m %p bcf %p fw size %zu)\n",
+		  i2400m, bcf, fw_size);
 	i2400m->boot_mode = 1;
 	wmb();		/* Make sure other readers see it */
 hw_reboot:
@@ -985,13 +1419,28 @@ int i2400m_fw_dnload(struct i2400m *i2400m, const struct i2400m_bcf_hdr *bcf,
 	 * Initialize the download, push the bytes to the device and
 	 * then jump to the new firmware. Note @ret is passed with the
 	 * offset of the jump instruction to _dnload_finalize()
+	 *
+	 * Note we need to use the BCF header in the firmware image
+	 * that matches the barker that the device sent when it
+	 * rebooted, so it has to be passed along.
 	 */
-	ret = i2400m_dnload_init(i2400m, bcf);	/* Init device's dnload */
+	ret = -EBADF;
+	bcf_hdr = i2400m_bcf_hdr_find(i2400m);
+	if (bcf_hdr == NULL)
+		goto error_bcf_hdr_find;
+
+	ret = i2400m_dnload_init(i2400m, bcf_hdr);
 	if (ret == -ERESTARTSYS)
 		goto error_dev_rebooted;
 	if (ret < 0)
 		goto error_dnload_init;
 
+	/*
+	 * bcf_size refers to one header size plus the fw sections size
+	 * indicated by the header,ie. if there are other extended headers
+	 * at the tail, they are not counted
+	 */
+	bcf_size = sizeof(u32) * le32_to_cpu(bcf_hdr->size);
 	ret = i2400m_dnload_bcf(i2400m, bcf, bcf_size);
 	if (ret == -ERESTARTSYS)
 		goto error_dev_rebooted;
@@ -1001,7 +1450,7 @@ int i2400m_fw_dnload(struct i2400m *i2400m, const struct i2400m_bcf_hdr *bcf,
 		goto error_dnload_bcf;
 	}
 
-	ret = i2400m_dnload_finalize(i2400m, bcf, ret);
+	ret = i2400m_dnload_finalize(i2400m, bcf_hdr, bcf, ret);
 	if (ret == -ERESTARTSYS)
 		goto error_dev_rebooted;
 	if (ret < 0) {
@@ -1018,10 +1467,11 @@ int i2400m_fw_dnload(struct i2400m *i2400m, const struct i2400m_bcf_hdr *bcf,
 error_dnload_finalize:
 error_dnload_bcf:
 error_dnload_init:
+error_bcf_hdr_find:
 error_bootrom_init:
 error_too_many_reboots:
 	d_fnend(5, dev, "(i2400m %p bcf %p size %zu) = %d\n",
-		i2400m, bcf, bcf_size, ret);
+		i2400m, bcf, fw_size, ret);
 	return ret;
 
 error_dev_rebooted:
@@ -1031,6 +1481,61 @@ int i2400m_fw_dnload(struct i2400m *i2400m, const struct i2400m_bcf_hdr *bcf,
 	goto hw_reboot;
 }
 
+static
+int i2400m_fw_bootstrap(struct i2400m *i2400m, const struct firmware *fw,
+			enum i2400m_bri flags)
+{
+	int ret;
+	struct device *dev = i2400m_dev(i2400m);
+	const struct i2400m_bcf_hdr *bcf;	/* Firmware data */
+
+	d_fnstart(5, dev, "(i2400m %p)\n", i2400m);
+	bcf = (void *) fw->data;
+	ret = i2400m_fw_check(i2400m, bcf, fw->size);
+	if (ret >= 0)
+		ret = i2400m_fw_dnload(i2400m, bcf, fw->size, flags);
+	if (ret < 0)
+		dev_err(dev, "%s: cannot use: %d, skipping\n",
+			i2400m->fw_name, ret);
+	kfree(i2400m->fw_hdrs);
+	i2400m->fw_hdrs = NULL;
+	d_fnend(5, dev, "(i2400m %p) = %d\n", i2400m, ret);
+	return ret;
+}
+
+
+/* Refcounted container for firmware data */
+struct i2400m_fw {
+	struct kref kref;
+	const struct firmware *fw;
+};
+
+
+static
+void i2400m_fw_destroy(struct kref *kref)
+{
+	struct i2400m_fw *i2400m_fw =
+		container_of(kref, struct i2400m_fw, kref);
+	release_firmware(i2400m_fw->fw);
+	kfree(i2400m_fw);
+}
+
+
+static
+struct i2400m_fw *i2400m_fw_get(struct i2400m_fw *i2400m_fw)
+{
+	if (i2400m_fw != NULL && i2400m_fw != (void *) ~0)
+		kref_get(&i2400m_fw->kref);
+	return i2400m_fw;
+}
+
+
+static
+void i2400m_fw_put(struct i2400m_fw *i2400m_fw)
+{
+	kref_put(&i2400m_fw->kref, i2400m_fw_destroy);
+}
+
 
 /**
  * i2400m_dev_bootstrap - Bring the device to a known state and upload firmware
@@ -1049,42 +1554,109 @@ int i2400m_fw_dnload(struct i2400m *i2400m, const struct i2400m_bcf_hdr *bcf,
  */
 int i2400m_dev_bootstrap(struct i2400m *i2400m, enum i2400m_bri flags)
 {
-	int ret = 0, itr = 0;
+	int ret, itr;
 	struct device *dev = i2400m_dev(i2400m);
-	const struct firmware *fw;
+	struct i2400m_fw *i2400m_fw;
 	const struct i2400m_bcf_hdr *bcf;	/* Firmware data */
+	const struct firmware *fw;
 	const char *fw_name;
 
 	d_fnstart(5, dev, "(i2400m %p)\n", i2400m);
 
+	ret = -ENODEV;
+	spin_lock(&i2400m->rx_lock);
+	i2400m_fw = i2400m_fw_get(i2400m->fw_cached);
+	spin_unlock(&i2400m->rx_lock);
+	if (i2400m_fw == (void *) ~0) {
+		dev_err(dev, "can't load firmware now!");
+		goto out;
+	} else if (i2400m_fw != NULL) {
+		dev_info(dev, "firmware %s: loading from cache\n",
+			 i2400m->fw_name);
+		ret = i2400m_fw_bootstrap(i2400m, i2400m_fw->fw, flags);
+		i2400m_fw_put(i2400m_fw);
+		goto out;
+	}
+
 	/* Load firmware files to memory. */
-	itr = 0;
-	while(1) {
+	for (itr = 0, bcf = NULL, ret = -ENOENT; ; itr++) {
 		fw_name = i2400m->bus_fw_names[itr];
 		if (fw_name == NULL) {
 			dev_err(dev, "Could not find a usable firmware image\n");
-			ret = -ENOENT;
-			goto error_no_fw;
+			break;
 		}
+		d_printf(1, dev, "trying firmware %s (%d)\n", fw_name, itr);
 		ret = request_firmware(&fw, fw_name, dev);
-		if (ret == 0)
-			break;		/* got it */
-		if (ret < 0)
+		if (ret < 0) {
 			dev_err(dev, "fw %s: cannot load file: %d\n",
 				fw_name, ret);
-		itr++;
+			continue;
+		}
+		i2400m->fw_name = fw_name;
+		ret = i2400m_fw_bootstrap(i2400m, fw, flags);
+		release_firmware(fw);
+		if (ret >= 0)	/* firmware loaded succesfully */
+			break;
+		i2400m->fw_name = NULL;
 	}
-
-	bcf = (void *) fw->data;
-	i2400m->fw_name = fw_name;
-	ret = i2400m_fw_check(i2400m, bcf, fw->size);
-	if (ret < 0)
-		goto error_fw_bad;
-	ret = i2400m_fw_dnload(i2400m, bcf, fw->size, flags);
-error_fw_bad:
-	release_firmware(fw);
-error_no_fw:
+out:
 	d_fnend(5, dev, "(i2400m %p) = %d\n", i2400m, ret);
 	return ret;
 }
 EXPORT_SYMBOL_GPL(i2400m_dev_bootstrap);
+
+
+void i2400m_fw_cache(struct i2400m *i2400m)
+{
+	int result;
+	struct i2400m_fw *i2400m_fw;
+	struct device *dev = i2400m_dev(i2400m);
+
+	/* if there is anything there, free it -- now, this'd be weird */
+	spin_lock(&i2400m->rx_lock);
+	i2400m_fw = i2400m->fw_cached;
+	spin_unlock(&i2400m->rx_lock);
+	if (i2400m_fw != NULL && i2400m_fw != (void *) ~0) {
+		i2400m_fw_put(i2400m_fw);
+		WARN(1, "%s:%u: still cached fw still present?\n",
+		     __func__, __LINE__);
+	}
+
+	if (i2400m->fw_name == NULL) {
+		dev_err(dev, "firmware n/a: can't cache\n");
+		i2400m_fw = (void *) ~0;
+		goto out;
+	}
+
+	i2400m_fw = kzalloc(sizeof(*i2400m_fw), GFP_ATOMIC);
+	if (i2400m_fw == NULL)
+		goto out;
+	kref_init(&i2400m_fw->kref);
+	result = request_firmware(&i2400m_fw->fw, i2400m->fw_name, dev);
+	if (result < 0) {
+		dev_err(dev, "firmware %s: failed to cache: %d\n",
+			i2400m->fw_name, result);
+		kfree(i2400m_fw);
+		i2400m_fw = (void *) ~0;
+	} else
+		dev_info(dev, "firmware %s: cached\n", i2400m->fw_name);
+out:
+	spin_lock(&i2400m->rx_lock);
+	i2400m->fw_cached = i2400m_fw;
+	spin_unlock(&i2400m->rx_lock);
+}
+
+
+void i2400m_fw_uncache(struct i2400m *i2400m)
+{
+	struct i2400m_fw *i2400m_fw;
+
+	spin_lock(&i2400m->rx_lock);
+	i2400m_fw = i2400m->fw_cached;
+	i2400m->fw_cached = NULL;
+	spin_unlock(&i2400m->rx_lock);
+
+	if (i2400m_fw != NULL && i2400m_fw != (void *) ~0)
+		i2400m_fw_put(i2400m_fw);
+}
+

drivers/net/wimax/i2400m/i2400m-sdio.h

@@ -67,6 +67,7 @@
 
 /* Host-Device interface for SDIO */
 enum {
+	I2400M_SDIO_BOOT_RETRIES = 3,
 	I2400MS_BLK_SIZE = 256,
 	I2400MS_PL_SIZE_MAX = 0x3E00,
 
@@ -77,9 +78,11 @@ enum {
 	I2400MS_INTR_GET_SIZE_ADDR = 0x2C,
 	/* The number of ticks to wait for the device to signal that
 	 * it is ready */
-	I2400MS_INIT_SLEEP_INTERVAL = 10,
+	I2400MS_INIT_SLEEP_INTERVAL = 100,
 	/* How long to wait for the device to settle after reset */
 	I2400MS_SETTLE_TIME = 40,
+	/* The number of msec to wait for IOR after sending IOE */
+	IWMC3200_IOR_TIMEOUT = 10,
 };
 
 
@@ -97,6 +100,14 @@ enum {
  * @tx_workqueue: workqeueue used for data TX; we don't use the
  *     system's workqueue as that might cause deadlocks with code in
  *     the bus-generic driver.
+ *
+ * @debugfs_dentry: dentry for the SDIO specific debugfs files
+ *
+ *     Note this value is set to NULL upon destruction; this is
+ *     because some routinges use it to determine if we are inside the
+ *     probe() path or some other path. When debugfs is disabled,
+ *     creation sets the dentry to '(void*) -ENODEV', which is valid
+ *     for the test.
  */
 struct i2400ms {
 	struct i2400m i2400m;		/* FIRST! See doc */
@@ -111,6 +122,9 @@ struct i2400ms {
 	wait_queue_head_t bm_wfa_wq;
 	int bm_wait_result;
 	size_t bm_ack_size;
+
+	/* Device is any of the iwmc3200 SKUs */
+	unsigned iwmc3200:1;
 };
 
 

drivers/net/wimax/i2400m/i2400m-usb.h

@@ -88,6 +88,13 @@ struct edc {
 	u16 errorcount;
 };
 
+struct i2400m_endpoint_cfg {
+	unsigned char bulk_out;
+	unsigned char notification;
+	unsigned char reset_cold;
+	unsigned char bulk_in;
+};
+
 static inline void edc_init(struct edc *edc)
 {
 	edc->timestart = jiffies;
@@ -137,15 +144,13 @@ static inline int edc_inc(struct edc *edc, u16 max_err, u16 timeframe)
 
 /* Host-Device interface for USB */
 enum {
+	I2400M_USB_BOOT_RETRIES = 3,
 	I2400MU_MAX_NOTIFICATION_LEN = 256,
 	I2400MU_BLK_SIZE = 16,
 	I2400MU_PL_SIZE_MAX = 0x3EFF,
 
-	/* Endpoints */
-	I2400MU_EP_BULK_OUT = 0,
-	I2400MU_EP_NOTIFICATION,
-	I2400MU_EP_RESET_COLD,
-	I2400MU_EP_BULK_IN,
+	/* Device IDs */
+	USB_DEVICE_ID_I6050 = 0x0186,
 };
 
 
@@ -215,6 +220,7 @@ struct i2400mu {
 	struct usb_device *usb_dev;
 	struct usb_interface *usb_iface;
 	struct edc urb_edc;		/* Error density counter */
+	struct i2400m_endpoint_cfg endpoint_cfg;
 
 	struct urb *notif_urb;
 	struct task_struct *tx_kthread;

drivers/net/wimax/i2400m/i2400m.h

@@ -117,16 +117,30 @@
  * well as i2400m->wimax_dev.net_dev and call i2400m_setup(). The
  * i2400m driver will only register with the WiMAX and network stacks;
  * the only access done to the device is to read the MAC address so we
- * can register a network device. This calls i2400m_dev_start() to
- * load firmware, setup communication with the device and configure it
- * for operation.
+ * can register a network device.
  *
- * At this point, control and data communications are possible.
+ * The high-level call flow is:
+ *
+ * bus_probe()
+ *   i2400m_setup()
+ *     i2400m->bus_setup()
+ *     boot rom initialization / read mac addr
+ *     network / WiMAX stacks registration
+ *     i2400m_dev_start()
+ *       i2400m->bus_dev_start()
+ *       i2400m_dev_initialize()
  *
- * On disconnect/driver unload, the bus-specific disconnect function
- * calls i2400m_release() to undo i2400m_setup(). i2400m_dev_stop()
- * shuts the firmware down and releases resources uses to communicate
- * with the device.
+ * The reverse applies for a disconnect() call:
+ *
+ * bus_disconnect()
+ *   i2400m_release()
+ *     i2400m_dev_stop()
+ *       i2400m_dev_shutdown()
+ *       i2400m->bus_dev_stop()
+ *     network / WiMAX stack unregistration
+ *     i2400m->bus_release()
+ *
+ * At this point, control and data communications are possible.
  *
  * While the device is up, it might reset. The bus-specific driver has
  * to catch that situation and call i2400m_dev_reset_handle() to deal
@@ -148,9 +162,6 @@
 
 /* Misc constants */
 enum {
-	/* Firmware uploading */
-	I2400M_BOOT_RETRIES = 3,
-	I3200_BOOT_RETRIES = 3,
 	/* Size of the Boot Mode Command buffer */
 	I2400M_BM_CMD_BUF_SIZE = 16 * 1024,
 	I2400M_BM_ACK_BUF_SIZE = 256,
@@ -197,6 +208,7 @@ enum i2400m_reset_type {
 
 struct i2400m_reset_ctx;
 struct i2400m_roq;
+struct i2400m_barker_db;
 
 /**
  * struct i2400m - descriptor for an Intel 2400m
@@ -204,27 +216,50 @@ struct i2400m_roq;
  * Members marked with [fill] must be filled out/initialized before
  * calling i2400m_setup().
  *
+ * Note the @bus_setup/@bus_release, @bus_dev_start/@bus_dev_release
+ * call pairs are very much doing almost the same, and depending on
+ * the underlying bus, some stuff has to be put in one or the
+ * other. The idea of setup/release is that they setup the minimal
+ * amount needed for loading firmware, where us dev_start/stop setup
+ * the rest needed to do full data/control traffic.
+ *
  * @bus_tx_block_size: [fill] SDIO imposes a 256 block size, USB 16,
  *     so we have a tx_blk_size variable that the bus layer sets to
  *     tell the engine how much of that we need.
  *
  * @bus_pl_size_max: [fill] Maximum payload size.
  *
- * @bus_dev_start: [fill] Function called by the bus-generic code
- *     [i2400m_dev_start()] to setup the bus-specific communications
- *     to the the device. See LIFE CYCLE above.
+ * @bus_setup: [optional fill] Function called by the bus-generic code
+ *     [i2400m_setup()] to setup the basic bus-specific communications
+ *     to the the device needed to load firmware. See LIFE CYCLE above.
  *
  *     NOTE: Doesn't need to upload the firmware, as that is taken
  *     care of by the bus-generic code.
  *
- * @bus_dev_stop: [fill] Function called by the bus-generic code
- *     [i2400m_dev_stop()] to shutdown the bus-specific communications
- *     to the the device. See LIFE CYCLE above.
+ * @bus_release: [optional fill] Function called by the bus-generic
+ *     code [i2400m_release()] to shutdown the basic bus-specific
+ *     communications to the the device needed to load firmware. See
+ *     LIFE CYCLE above.
  *
  *     This function does not need to reset the device, just tear down
  *     all the host resources created to  handle communication with
  *     the device.
  *
+ * @bus_dev_start: [optional fill] Function called by the bus-generic
+ *     code [i2400m_dev_start()] to do things needed to start the
+ *     device. See LIFE CYCLE above.
+ *
+ *     NOTE: Doesn't need to upload the firmware, as that is taken
+ *     care of by the bus-generic code.
+ *
+ * @bus_dev_stop: [optional fill] Function called by the bus-generic
+ *     code [i2400m_dev_stop()] to do things needed for stopping the
+ *     device. See LIFE CYCLE above.
+ *
+ *     This function does not need to reset the device, just tear down
+ *     all the host resources created to handle communication with
+ *     the device.
+ *
  * @bus_tx_kick: [fill] Function called by the bus-generic code to let
  *     the bus-specific code know that there is data available in the
  *     TX FIFO for transmission to the device.
@@ -246,6 +281,9 @@ struct i2400m_roq;
  *     process, so it cannot rely on common infrastructure being laid
  *     out.
  *
+ *     IMPORTANT: don't call reset on RT_BUS with i2400m->init_mutex
+ *     held, as the .pre/.post reset handlers will deadlock.
+ *
  * @bus_bm_retries: [fill] How many times shall a firmware upload /
  *     device initialization be retried? Different models of the same
  *     device might need different values, hence it is set by the
@@ -297,6 +335,27 @@ struct i2400m_roq;
  *     force this to be the first field so that we can get from
  *     netdev_priv() the right pointer.
  *
+ * @updown: the device is up and ready for transmitting control and
+ *     data packets. This implies @ready (communication infrastructure
+ *     with the device is ready) and the device's firmware has been
+ *     loaded and the device initialized.
+ *
+ *     Write to it only inside a i2400m->init_mutex protected area
+ *     followed with a wmb(); rmb() before accesing (unless locked
+ *     inside i2400m->init_mutex). Read access can be loose like that
+ *     [just using rmb()] because the paths that use this also do
+ *     other error checks later on.
+ *
+ * @ready: Communication infrastructure with the device is ready, data
+ *     frames can start to be passed around (this is lighter than
+ *     using the WiMAX state for certain hot paths).
+ *
+ *     Write to it only inside a i2400m->init_mutex protected area
+ *     followed with a wmb(); rmb() before accesing (unless locked
+ *     inside i2400m->init_mutex). Read access can be loose like that
+ *     [just using rmb()] because the paths that use this also do
+ *     other error checks later on.
+ *
  * @rx_reorder: 1 if RX reordering is enabled; this can only be
  *     set at probe time.
  *
@@ -362,6 +421,13 @@ struct i2400m_roq;
  *     delivered. Then the driver can release them to the host. See
  *     drivers/net/i2400m/rx.c for details.
  *
+ * @rx_reports: reports received from the device that couldn't be
+ *     processed because the driver wasn't still ready; when ready,
+ *     they are pulled from here and chewed.
+ *
+ * @rx_reports_ws: Work struct used to kick a scan of the RX reports
+ *     list and to process each.
+ *
  * @src_mac_addr: MAC address used to make ethernet packets be coming
  *     from. This is generated at i2400m_setup() time and used during
  *     the life cycle of the instance. See i2400m_fake_eth_header().
@@ -422,6 +488,25 @@ struct i2400m_roq;
  *
  * @fw_version: version of the firmware interface, Major.minor,
  *     encoded in the high word and low word (major << 16 | minor).
+ *
+ * @fw_hdrs: NULL terminated array of pointers to the firmware
+ *     headers. This is only available during firmware load time.
+ *
+ * @fw_cached: Used to cache firmware when the system goes to
+ *     suspend/standby/hibernation (as on resume we can't read it). If
+ *     NULL, no firmware was cached, read it. If ~0, you can't read
+ *     any firmware files (the system still didn't come out of suspend
+ *     and failed to cache one), so abort; otherwise, a valid cached
+ *     firmware to be used. Access to this variable is protected by
+ *     the spinlock i2400m->rx_lock.
+ *
+ * @barker: barker type that the device uses; this is initialized by
+ *     i2400m_is_boot_barker() the first time it is called. Then it
+ *     won't change during the life cycle of the device and everytime
+ *     a boot barker is received, it is just verified for it being the
+ *     same.
+ *
+ * @pm_notifier: used to register for PM events
  */
 struct i2400m {
 	struct wimax_dev wimax_dev;	/* FIRST! See doc */
@@ -429,7 +514,7 @@ struct i2400m {
 	unsigned updown:1;		/* Network device is up or down */
 	unsigned boot_mode:1;		/* is the device in boot mode? */
 	unsigned sboot:1;		/* signed or unsigned fw boot */
-	unsigned ready:1;		/* all probing steps done */
+	unsigned ready:1;		/* Device comm infrastructure ready */
 	unsigned rx_reorder:1;		/* RX reorder is enabled */
 	u8 trace_msg_from_user;		/* echo rx msgs to 'trace' pipe */
 					/* typed u8 so /sys/kernel/debug/u8 can tweak */
@@ -440,8 +525,10 @@ struct i2400m {
 	size_t bus_pl_size_max;
 	unsigned bus_bm_retries;
 
+	int (*bus_setup)(struct i2400m *);
 	int (*bus_dev_start)(struct i2400m *);
 	void (*bus_dev_stop)(struct i2400m *);
+	void (*bus_release)(struct i2400m *);
 	void (*bus_tx_kick)(struct i2400m *);
 	int (*bus_reset)(struct i2400m *, enum i2400m_reset_type);
 	ssize_t (*bus_bm_cmd_send)(struct i2400m *,
@@ -468,6 +555,8 @@ struct i2400m {
 		rx_num, rx_size_acc, rx_size_min, rx_size_max;
 	struct i2400m_roq *rx_roq;	/* not under rx_lock! */
 	u8 src_mac_addr[ETH_HLEN];
+	struct list_head rx_reports;	/* under rx_lock! */
+	struct work_struct rx_report_ws;
 
 	struct mutex msg_mutex;		/* serialize command execution */
 	struct completion msg_completion;
@@ -487,37 +576,12 @@ struct i2400m {
 	struct dentry *debugfs_dentry;
 	const char *fw_name;		/* name of the current firmware image */
 	unsigned long fw_version;	/* version of the firmware interface */
-};
-
+	const struct i2400m_bcf_hdr **fw_hdrs;
+	struct i2400m_fw *fw_cached;	/* protected by rx_lock */
+	struct i2400m_barker_db *barker;
 
-/*
- * Initialize a 'struct i2400m' from all zeroes
- *
- * This is a bus-generic API call.
- */
-static inline
-void i2400m_init(struct i2400m *i2400m)
-{
-	wimax_dev_init(&i2400m->wimax_dev);
-
-	i2400m->boot_mode = 1;
-	i2400m->rx_reorder = 1;
-	init_waitqueue_head(&i2400m->state_wq);
-
-	spin_lock_init(&i2400m->tx_lock);
-	i2400m->tx_pl_min = UINT_MAX;
-	i2400m->tx_size_min = UINT_MAX;
-
-	spin_lock_init(&i2400m->rx_lock);
-	i2400m->rx_pl_min = UINT_MAX;
-	i2400m->rx_size_min = UINT_MAX;
-
-	mutex_init(&i2400m->msg_mutex);
-	init_completion(&i2400m->msg_completion);
-
-	mutex_init(&i2400m->init_mutex);
-	/* wake_tx_ws is initialized in i2400m_tx_setup() */
-}
+	struct notifier_block pm_notifier;
+};
 
 
 /*
@@ -577,6 +641,14 @@ extern void i2400m_bm_cmd_prepare(struct i2400m_bootrom_header *);
 extern int i2400m_dev_bootstrap(struct i2400m *, enum i2400m_bri);
 extern int i2400m_read_mac_addr(struct i2400m *);
 extern int i2400m_bootrom_init(struct i2400m *, enum i2400m_bri);
+extern int i2400m_is_boot_barker(struct i2400m *, const void *, size_t);
+static inline
+int i2400m_is_d2h_barker(const void *buf)
+{
+	const __le32 *barker = buf;
+	return le32_to_cpu(*barker) == I2400M_D2H_MSG_BARKER;
+}
+extern void i2400m_unknown_barker(struct i2400m *, const void *, size_t);
 
 /* Make/grok boot-rom header commands */
 
@@ -644,6 +716,8 @@ unsigned i2400m_brh_get_signature(const struct i2400m_bootrom_header *hdr)
 /*
  * Driver / device setup and internal functions
  */
+extern void i2400m_init(struct i2400m *);
+extern int i2400m_reset(struct i2400m *, enum i2400m_reset_type);
 extern void i2400m_netdev_setup(struct net_device *net_dev);
 extern int i2400m_sysfs_setup(struct device_driver *);
 extern void i2400m_sysfs_release(struct device_driver *);
@@ -654,10 +728,14 @@ extern void i2400m_tx_release(struct i2400m *);
 extern int i2400m_rx_setup(struct i2400m *);
 extern void i2400m_rx_release(struct i2400m *);
 
+extern void i2400m_fw_cache(struct i2400m *);
+extern void i2400m_fw_uncache(struct i2400m *);
+
 extern void i2400m_net_rx(struct i2400m *, struct sk_buff *, unsigned,
 			  const void *, int);
 extern void i2400m_net_erx(struct i2400m *, struct sk_buff *,
 			   enum i2400m_cs);
+extern void i2400m_net_wake_stop(struct i2400m *);
 enum i2400m_pt;
 extern int i2400m_tx(struct i2400m *, const void *, size_t, enum i2400m_pt);
 
@@ -672,14 +750,12 @@ static inline int i2400m_debugfs_add(struct i2400m *i2400m)
 static inline void i2400m_debugfs_rm(struct i2400m *i2400m) {}
 #endif
 
-/* Called by _dev_start()/_dev_stop() to initialize the device itself */
+/* Initialize/shutdown the device */
 extern int i2400m_dev_initialize(struct i2400m *);
 extern void i2400m_dev_shutdown(struct i2400m *);
 
 extern struct attribute_group i2400m_dev_attr_group;
 
-extern int i2400m_schedule_work(struct i2400m *,
-				void (*)(struct work_struct *), gfp_t);
 
 /* HDI message's payload description handling */
 
@@ -724,7 +800,9 @@ void i2400m_put(struct i2400m *i2400m)
 	dev_put(i2400m->wimax_dev.net_dev);
 }
 
-extern int i2400m_dev_reset_handle(struct i2400m *);
+extern int i2400m_dev_reset_handle(struct i2400m *, const char *);
+extern int i2400m_pre_reset(struct i2400m *);
+extern int i2400m_post_reset(struct i2400m *);
 
 /*
  * _setup()/_release() are called by the probe/disconnect functions of
@@ -737,20 +815,6 @@ extern int i2400m_rx(struct i2400m *, struct sk_buff *);
 extern struct i2400m_msg_hdr *i2400m_tx_msg_get(struct i2400m *, size_t *);
 extern void i2400m_tx_msg_sent(struct i2400m *);
 
-static const __le32 i2400m_NBOOT_BARKER[4] = {
-	cpu_to_le32(I2400M_NBOOT_BARKER),
-	cpu_to_le32(I2400M_NBOOT_BARKER),
-	cpu_to_le32(I2400M_NBOOT_BARKER),
-	cpu_to_le32(I2400M_NBOOT_BARKER)
-};
-
-static const __le32 i2400m_SBOOT_BARKER[4] = {
-	cpu_to_le32(I2400M_SBOOT_BARKER),
-	cpu_to_le32(I2400M_SBOOT_BARKER),
-	cpu_to_le32(I2400M_SBOOT_BARKER),
-	cpu_to_le32(I2400M_SBOOT_BARKER)
-};
-
 extern int i2400m_power_save_disabled;
 
 /*
@@ -773,10 +837,12 @@ struct device *i2400m_dev(struct i2400m *i2400m)
 struct i2400m_work {
 	struct work_struct ws;
 	struct i2400m *i2400m;
+	size_t pl_size;
 	u8 pl[0];
 };
-extern int i2400m_queue_work(struct i2400m *,
-			     void (*)(struct work_struct *), gfp_t,
+
+extern int i2400m_schedule_work(struct i2400m *,
+				void (*)(struct work_struct *), gfp_t,
 				const void *, size_t);
 
 extern int i2400m_msg_check_status(const struct i2400m_l3l4_hdr *,
@@ -789,6 +855,7 @@ extern void i2400m_msg_ack_hook(struct i2400m *,
 				const struct i2400m_l3l4_hdr *, size_t);
 extern void i2400m_report_hook(struct i2400m *,
 			       const struct i2400m_l3l4_hdr *, size_t);
+extern void i2400m_report_hook_work(struct work_struct *);
 extern int i2400m_cmd_enter_powersave(struct i2400m *);
 extern int i2400m_cmd_get_state(struct i2400m *);
 extern int i2400m_cmd_exit_idle(struct i2400m *);
@@ -849,6 +916,12 @@ void __i2400m_msleep(unsigned ms)
 #endif
 }
 
+
+/* module initialization helpers */
+extern int i2400m_barker_db_init(const char *);
+extern void i2400m_barker_db_exit(void);
+
+
 /* Module parameters */
 
 extern int i2400m_idle_mode_disabled;

drivers/net/wimax/i2400m/netdev.c

@@ -74,6 +74,7 @@
  */
 #include <linux/if_arp.h>
 #include <linux/netdevice.h>
+#include <linux/ethtool.h>
 #include "i2400m.h"
 
 
@@ -88,7 +89,10 @@ enum {
 	 * The MTU is 1400 or less
 	 */
 	I2400M_MAX_MTU = 1400,
-	I2400M_TX_TIMEOUT = HZ,
+	/* 20 secs? yep, this is the maximum timeout that the device
+	 * might take to get out of IDLE / negotiate it with the base
+	 * station. We add 1sec for good measure. */
+	I2400M_TX_TIMEOUT = 21 * HZ,
 	I2400M_TX_QLEN = 5,
 };
 
@@ -101,22 +105,19 @@ int i2400m_open(struct net_device *net_dev)
 	struct device *dev = i2400m_dev(i2400m);
 
 	d_fnstart(3, dev, "(net_dev %p [i2400m %p])\n", net_dev, i2400m);
-	if (i2400m->ready == 0) {
-		dev_err(dev, "Device is still initializing\n");
-		result = -EBUSY;
-	} else
+	/* Make sure we wait until init is complete... */
+	mutex_lock(&i2400m->init_mutex);
+	if (i2400m->updown)
 		result = 0;
+	else
+		result = -EBUSY;
+	mutex_unlock(&i2400m->init_mutex);
 	d_fnend(3, dev, "(net_dev %p [i2400m %p]) = %d\n",
 		net_dev, i2400m, result);
 	return result;
 }
 
 
-/*
- *
- * On kernel versions where cancel_work_sync() didn't return anything,
- * we rely on wake_tx_skb() being non-NULL.
- */
 static
 int i2400m_stop(struct net_device *net_dev)
 {
@@ -124,21 +125,7 @@ int i2400m_stop(struct net_device *net_dev)
 	struct device *dev = i2400m_dev(i2400m);
 
 	d_fnstart(3, dev, "(net_dev %p [i2400m %p])\n", net_dev, i2400m);
-	/* See i2400m_hard_start_xmit(), references are taken there
-	 * and here we release them if the work was still
-	 * pending. Note we can't differentiate work not pending vs
-	 * never scheduled, so the NULL check does that. */
-	if (cancel_work_sync(&i2400m->wake_tx_ws) == 0
-	    && i2400m->wake_tx_skb != NULL) {
-		unsigned long flags;
-		struct sk_buff *wake_tx_skb;
-		spin_lock_irqsave(&i2400m->tx_lock, flags);
-		wake_tx_skb = i2400m->wake_tx_skb;	/* compat help */
-		i2400m->wake_tx_skb = NULL;	/* compat help */
-		spin_unlock_irqrestore(&i2400m->tx_lock, flags);
-		i2400m_put(i2400m);
-		kfree_skb(wake_tx_skb);
-	}
+	i2400m_net_wake_stop(i2400m);
 	d_fnend(3, dev, "(net_dev %p [i2400m %p]) = 0\n", net_dev, i2400m);
 	return 0;
 }
@@ -167,6 +154,7 @@ void i2400m_wake_tx_work(struct work_struct *ws)
 {
 	int result;
 	struct i2400m *i2400m = container_of(ws, struct i2400m, wake_tx_ws);
+	struct net_device *net_dev = i2400m->wimax_dev.net_dev;
 	struct device *dev = i2400m_dev(i2400m);
 	struct sk_buff *skb = i2400m->wake_tx_skb;
 	unsigned long flags;
@@ -182,27 +170,36 @@ void i2400m_wake_tx_work(struct work_struct *ws)
 		dev_err(dev, "WAKE&TX: skb dissapeared!\n");
 		goto out_put;
 	}
+	/* If we have, somehow, lost the connection after this was
+	 * queued, don't do anything; this might be the device got
+	 * reset or just disconnected. */
+	if (unlikely(!netif_carrier_ok(net_dev)))
+		goto out_kfree;
 	result = i2400m_cmd_exit_idle(i2400m);
 	if (result == -EILSEQ)
 		result = 0;
 	if (result < 0) {
 		dev_err(dev, "WAKE&TX: device didn't get out of idle: "
-			"%d\n", result);
-			goto error;
+			"%d - resetting\n", result);
+		i2400m_reset(i2400m, I2400M_RT_BUS);
+		goto error;
 	}
 	result = wait_event_timeout(i2400m->state_wq,
-				    i2400m->state != I2400M_SS_IDLE, 5 * HZ);
+				    i2400m->state != I2400M_SS_IDLE,
+				    net_dev->watchdog_timeo - HZ/2);
 	if (result == 0)
 		result = -ETIMEDOUT;
 	if (result < 0) {
 		dev_err(dev, "WAKE&TX: error waiting for device to exit IDLE: "
-			"%d\n", result);
+			"%d - resetting\n", result);
+		i2400m_reset(i2400m, I2400M_RT_BUS);
 		goto error;
 	}
 	msleep(20);	/* device still needs some time or it drops it */
 	result = i2400m_tx(i2400m, skb->data, skb->len, I2400M_PT_DATA);
-	netif_wake_queue(i2400m->wimax_dev.net_dev);
 error:
+	netif_wake_queue(net_dev);
+out_kfree:
 	kfree_skb(skb);	/* refcount transferred by _hard_start_xmit() */
 out_put:
 	i2400m_put(i2400m);
@@ -229,6 +226,38 @@ void i2400m_tx_prep_header(struct sk_buff *skb)
 }
 
 
+
+/*
+ * Cleanup resources acquired during i2400m_net_wake_tx()
+ *
+ * This is called by __i2400m_dev_stop and means we have to make sure
+ * the workqueue is flushed from any pending work.
+ */
+void i2400m_net_wake_stop(struct i2400m *i2400m)
+{
+	struct device *dev = i2400m_dev(i2400m);
+
+	d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
+	/* See i2400m_hard_start_xmit(), references are taken there
+	 * and here we release them if the work was still
+	 * pending. Note we can't differentiate work not pending vs
+	 * never scheduled, so the NULL check does that. */
+	if (cancel_work_sync(&i2400m->wake_tx_ws) == 0
+	    && i2400m->wake_tx_skb != NULL) {
+		unsigned long flags;
+		struct sk_buff *wake_tx_skb;
+		spin_lock_irqsave(&i2400m->tx_lock, flags);
+		wake_tx_skb = i2400m->wake_tx_skb;	/* compat help */
+		i2400m->wake_tx_skb = NULL;	/* compat help */
+		spin_unlock_irqrestore(&i2400m->tx_lock, flags);
+		i2400m_put(i2400m);
+		kfree_skb(wake_tx_skb);
+	}
+	d_fnend(3, dev, "(i2400m %p) = void\n", i2400m);
+	return;
+}
+
+
 /*
  * TX an skb to an idle device
  *
@@ -342,6 +371,20 @@ netdev_tx_t i2400m_hard_start_xmit(struct sk_buff *skb,
 	int result;
 
 	d_fnstart(3, dev, "(skb %p net_dev %p)\n", skb, net_dev);
+	if (skb_header_cloned(skb)) {
+		/*
+		 * Make tcpdump/wireshark happy -- if they are
+		 * running, the skb is cloned and we will overwrite
+		 * the mac fields in i2400m_tx_prep_header. Expand
+		 * seems to fix this...
+		 */
+		result = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
+		if (result) {
+			result = NETDEV_TX_BUSY;
+			goto error_expand;
+		}
+	}
+
 	if (i2400m->state == I2400M_SS_IDLE)
 		result = i2400m_net_wake_tx(i2400m, net_dev, skb);
 	else
@@ -352,10 +395,11 @@ netdev_tx_t i2400m_hard_start_xmit(struct sk_buff *skb,
 		net_dev->stats.tx_packets++;
 		net_dev->stats.tx_bytes += skb->len;
 	}
+	result = NETDEV_TX_OK;
+error_expand:
 	kfree_skb(skb);
-
-	d_fnend(3, dev, "(skb %p net_dev %p)\n", skb, net_dev);
-	return NETDEV_TX_OK;
+	d_fnend(3, dev, "(skb %p net_dev %p) = %d\n", skb, net_dev, result);
+	return result;
 }
 
 
@@ -559,6 +603,22 @@ static const struct net_device_ops i2400m_netdev_ops = {
 	.ndo_change_mtu = i2400m_change_mtu,
 };
 
+static void i2400m_get_drvinfo(struct net_device *net_dev,
+			       struct ethtool_drvinfo *info)
+{
+	struct i2400m *i2400m = net_dev_to_i2400m(net_dev);
+
+	strncpy(info->driver, KBUILD_MODNAME, sizeof(info->driver) - 1);
+	strncpy(info->fw_version, i2400m->fw_name, sizeof(info->fw_version) - 1);
+	if (net_dev->dev.parent)
+		strncpy(info->bus_info, dev_name(net_dev->dev.parent),
+			sizeof(info->bus_info) - 1);
+}
+
+static const struct ethtool_ops i2400m_ethtool_ops = {
+	.get_drvinfo = i2400m_get_drvinfo,
+	.get_link = ethtool_op_get_link,
+};
 
 /**
  * i2400m_netdev_setup - Setup setup @net_dev's i2400m private data
@@ -580,6 +640,7 @@ void i2400m_netdev_setup(struct net_device *net_dev)
 		   & ~IFF_MULTICAST);
 	net_dev->watchdog_timeo = I2400M_TX_TIMEOUT;
 	net_dev->netdev_ops = &i2400m_netdev_ops;
+	net_dev->ethtool_ops = &i2400m_ethtool_ops;
 	d_fnend(3, NULL, "(net_dev %p) = void\n", net_dev);
 }
 EXPORT_SYMBOL_GPL(i2400m_netdev_setup);

drivers/net/wimax/i2400m/rx.c

@@ -158,30 +158,104 @@ struct i2400m_report_hook_args {
 	struct sk_buff *skb_rx;
 	const struct i2400m_l3l4_hdr *l3l4_hdr;
 	size_t size;
+	struct list_head list_node;
 };
 
 
 /*
  * Execute i2400m_report_hook in a workqueue
  *
- * Unpacks arguments from the deferred call, executes it and then
- * drops the references.
+ * Goes over the list of queued reports in i2400m->rx_reports and
+ * processes them.
  *
- * Obvious NOTE: References are needed because we are a separate
- *     thread; otherwise the buffer changes under us because it is
- *     released by the original caller.
+ * NOTE: refcounts on i2400m are not needed because we flush the
+ *     workqueue this runs on (i2400m->work_queue) before destroying
+ *     i2400m.
  */
-static
 void i2400m_report_hook_work(struct work_struct *ws)
 {
-	struct i2400m_work *iw =
-		container_of(ws, struct i2400m_work, ws);
-	struct i2400m_report_hook_args *args = (void *) iw->pl;
-	if (iw->i2400m->ready)
-		i2400m_report_hook(iw->i2400m, args->l3l4_hdr, args->size);
-	kfree_skb(args->skb_rx);
-	i2400m_put(iw->i2400m);
-	kfree(iw);
+	struct i2400m *i2400m = container_of(ws, struct i2400m, rx_report_ws);
+	struct device *dev = i2400m_dev(i2400m);
+	struct i2400m_report_hook_args *args, *args_next;
+	LIST_HEAD(list);
+	unsigned long flags;
+
+	while (1) {
+		spin_lock_irqsave(&i2400m->rx_lock, flags);
+		list_splice_init(&i2400m->rx_reports, &list);
+		spin_unlock_irqrestore(&i2400m->rx_lock, flags);
+		if (list_empty(&list))
+			break;
+		else
+			d_printf(1, dev, "processing queued reports\n");
+		list_for_each_entry_safe(args, args_next, &list, list_node) {
+			d_printf(2, dev, "processing queued report %p\n", args);
+			i2400m_report_hook(i2400m, args->l3l4_hdr, args->size);
+			kfree_skb(args->skb_rx);
+			list_del(&args->list_node);
+			kfree(args);
+		}
+	}
+}
+
+
+/*
+ * Flush the list of queued reports
+ */
+static
+void i2400m_report_hook_flush(struct i2400m *i2400m)
+{
+	struct device *dev = i2400m_dev(i2400m);
+	struct i2400m_report_hook_args *args, *args_next;
+	LIST_HEAD(list);
+	unsigned long flags;
+
+	d_printf(1, dev, "flushing queued reports\n");
+	spin_lock_irqsave(&i2400m->rx_lock, flags);
+	list_splice_init(&i2400m->rx_reports, &list);
+	spin_unlock_irqrestore(&i2400m->rx_lock, flags);
+	list_for_each_entry_safe(args, args_next, &list, list_node) {
+		d_printf(2, dev, "flushing queued report %p\n", args);
+		kfree_skb(args->skb_rx);
+		list_del(&args->list_node);
+		kfree(args);
+	}
+}
+
+
+/*
+ * Queue a report for later processing
+ *
+ * @i2400m: device descriptor
+ * @skb_rx: skb that contains the payload (for reference counting)
+ * @l3l4_hdr: pointer to the control
+ * @size: size of the message
+ */
+static
+void i2400m_report_hook_queue(struct i2400m *i2400m, struct sk_buff *skb_rx,
+			      const void *l3l4_hdr, size_t size)
+{
+	struct device *dev = i2400m_dev(i2400m);
+	unsigned long flags;
+	struct i2400m_report_hook_args *args;
+
+	args = kzalloc(sizeof(*args), GFP_NOIO);
+	if (args) {
+		args->skb_rx = skb_get(skb_rx);
+		args->l3l4_hdr = l3l4_hdr;
+		args->size = size;
+		spin_lock_irqsave(&i2400m->rx_lock, flags);
+		list_add_tail(&args->list_node, &i2400m->rx_reports);
+		spin_unlock_irqrestore(&i2400m->rx_lock, flags);
+		d_printf(2, dev, "queued report %p\n", args);
+		rmb();		/* see i2400m->ready's documentation  */
+		if (likely(i2400m->ready))	/* only send if up */
+			queue_work(i2400m->work_queue, &i2400m->rx_report_ws);
+	} else  {
+		if (printk_ratelimit())
+			dev_err(dev, "%s:%u: Can't allocate %zu B\n",
+				__func__, __LINE__, sizeof(*args));
+	}
 }
 
 
@@ -295,21 +369,29 @@ void i2400m_rx_ctl(struct i2400m *i2400m, struct sk_buff *skb_rx,
 		 msg_type, size);
 	d_dump(2, dev, l3l4_hdr, size);
 	if (msg_type & I2400M_MT_REPORT_MASK) {
-		/* These hooks have to be ran serialized; as well, the
-		 * handling might force the execution of commands, and
-		 * that might cause reentrancy issues with
-		 * bus-specific subdrivers and workqueues. So we run
-		 * it in a separate workqueue. */
-		struct i2400m_report_hook_args args = {
-			.skb_rx = skb_rx,
-			.l3l4_hdr = l3l4_hdr,
-			.size = size
-		};
-		if (unlikely(i2400m->ready == 0))	/* only send if up */
-			return;
-		skb_get(skb_rx);
-		i2400m_queue_work(i2400m, i2400m_report_hook_work,
-				  GFP_KERNEL, &args, sizeof(args));
+		/*
+		 * Process each report
+		 *
+		 * - has to be ran serialized as well
+		 *
+		 * - the handling might force the execution of
+		 *   commands. That might cause reentrancy issues with
+		 *   bus-specific subdrivers and workqueues, so the we
+		 *   run it in a separate workqueue.
+		 *
+		 * - when the driver is not yet ready to handle them,
+		 *   they are queued and at some point the queue is
+		 *   restarted [NOTE: we can't queue SKBs directly, as
+		 *   this might be a piece of a SKB, not the whole
+		 *   thing, and this is cheaper than cloning the
+		 *   SKB].
+		 *
+		 * Note we don't do refcounting for the device
+		 * structure; this is because before destroying
+		 * 'i2400m', we make sure to flush the
+		 * i2400m->work_queue, so there are no issues.
+		 */
+		i2400m_report_hook_queue(i2400m, skb_rx, l3l4_hdr, size);
 		if (unlikely(i2400m->trace_msg_from_user))
 			wimax_msg(&i2400m->wimax_dev, "echo",
 				  l3l4_hdr, size, GFP_KERNEL);
@@ -363,8 +445,6 @@ void i2400m_rx_trace(struct i2400m *i2400m,
 		 msg_type & I2400M_MT_REPORT_MASK ? "REPORT" : "CMD/SET/GET",
 		 msg_type, size);
 	d_dump(2, dev, l3l4_hdr, size);
-	if (unlikely(i2400m->ready == 0))	/* only send if up */
-		return;
 	result = wimax_msg(wimax_dev, "trace", l3l4_hdr, size, GFP_KERNEL);
 	if (result < 0)
 		dev_err(dev, "error sending trace to userspace: %d\n",
@@ -748,7 +828,7 @@ void i2400m_roq_queue(struct i2400m *i2400m, struct i2400m_roq *roq,
 		dev_err(dev, "SW BUG? queue nsn %d (lbn %u ws %u)\n",
 			nsn, lbn, roq->ws);
 		i2400m_roq_log_dump(i2400m, roq);
-		i2400m->bus_reset(i2400m, I2400M_RT_WARM);
+		i2400m_reset(i2400m, I2400M_RT_WARM);
 	} else {
 		__i2400m_roq_queue(i2400m, roq, skb, lbn, nsn);
 		i2400m_roq_log_add(i2400m, roq, I2400M_RO_TYPE_PACKET,
@@ -814,7 +894,7 @@ void i2400m_roq_queue_update_ws(struct i2400m *i2400m, struct i2400m_roq *roq,
 		dev_err(dev, "SW BUG? queue_update_ws nsn %u (sn %u ws %u)\n",
 			nsn, sn, roq->ws);
 		i2400m_roq_log_dump(i2400m, roq);
-		i2400m->bus_reset(i2400m, I2400M_RT_WARM);
+		i2400m_reset(i2400m, I2400M_RT_WARM);
 	} else {
 		/* if the queue is empty, don't bother as we'd queue
 		 * it and inmediately unqueue it -- just deliver it */
@@ -1194,6 +1274,28 @@ int i2400m_rx(struct i2400m *i2400m, struct sk_buff *skb)
 EXPORT_SYMBOL_GPL(i2400m_rx);
 
 
+void i2400m_unknown_barker(struct i2400m *i2400m,
+			   const void *buf, size_t size)
+{
+	struct device *dev = i2400m_dev(i2400m);
+	char prefix[64];
+	const __le32 *barker = buf;
+	dev_err(dev, "RX: HW BUG? unknown barker %08x, "
+		"dropping %zu bytes\n", le32_to_cpu(*barker), size);
+	snprintf(prefix, sizeof(prefix), "%s %s: ",
+		 dev_driver_string(dev), dev_name(dev));
+	if (size > 64) {
+		print_hex_dump(KERN_ERR, prefix, DUMP_PREFIX_OFFSET,
+			       8, 4, buf, 64, 0);
+		printk(KERN_ERR "%s... (only first 64 bytes "
+		       "dumped)\n", prefix);
+	} else
+		print_hex_dump(KERN_ERR, prefix, DUMP_PREFIX_OFFSET,
+			       8, 4, buf, size, 0);
+}
+EXPORT_SYMBOL(i2400m_unknown_barker);
+
+
 /*
  * Initialize the RX queue and infrastructure
  *
@@ -1261,4 +1363,6 @@ void i2400m_rx_release(struct i2400m *i2400m)
 		kfree(i2400m->rx_roq[0].log);
 		kfree(i2400m->rx_roq);
 	}
+	/* at this point, nothing can be received... */
+	i2400m_report_hook_flush(i2400m);
 }

drivers/net/wimax/i2400m/sdio-fw.c

@@ -118,7 +118,8 @@ ssize_t i2400ms_bus_bm_cmd_send(struct i2400m *i2400m,
 	if (cmd_size > I2400M_BM_CMD_BUF_SIZE)
 		goto error_too_big;
 
-	memcpy(i2400m->bm_cmd_buf, _cmd, cmd_size);	/* Prep command */
+	if (_cmd != i2400m->bm_cmd_buf)
+		memmove(i2400m->bm_cmd_buf, _cmd, cmd_size);
 	cmd = i2400m->bm_cmd_buf;
 	if (cmd_size_a > cmd_size)			/* Zero pad space */
 		memset(i2400m->bm_cmd_buf + cmd_size, 0, cmd_size_a - cmd_size);
@@ -177,10 +178,6 @@ ssize_t i2400ms_bus_bm_wait_for_ack(struct i2400m *i2400m,
 	d_fnstart(5, dev, "(i2400m %p ack %p size %zu)\n",
 		  i2400m, ack, ack_size);
 
-	spin_lock(&i2400m->rx_lock);
-	i2400ms->bm_ack_size = -EINPROGRESS;
-	spin_unlock(&i2400m->rx_lock);
-
 	result = wait_event_timeout(i2400ms->bm_wfa_wq,
 				    i2400ms->bm_ack_size != -EINPROGRESS,
 				    2 * HZ);
@@ -199,6 +196,10 @@ ssize_t i2400ms_bus_bm_wait_for_ack(struct i2400m *i2400m,
 		size = min(ack_size, i2400ms->bm_ack_size);
 		memcpy(ack, i2400m->bm_ack_buf, size);
 	}
+	/*
+	 * Remember always to clear the bm_ack_size to -EINPROGRESS
+	 * after the RX data is processed
+	 */
 	i2400ms->bm_ack_size = -EINPROGRESS;
 	spin_unlock(&i2400m->rx_lock);
 

drivers/net/wimax/i2400m/sdio-rx.c

@@ -53,6 +53,7 @@
  * i2400ms_irq()
  *   i2400ms_rx()
  *     __i2400ms_rx_get_size()
+ *     i2400m_is_boot_barker()
  *     i2400m_rx()
  *
  * i2400ms_rx_setup()
@@ -138,6 +139,11 @@ void i2400ms_rx(struct i2400ms *i2400ms)
 		ret = rx_size;
 		goto error_get_size;
 	}
+	/*
+	 * Hardware quirk: make sure to clear the INTR status register
+	 * AFTER getting the data transfer size.
+	 */
+	sdio_writeb(func, 1, I2400MS_INTR_CLEAR_ADDR, &ret);
 
 	ret = -ENOMEM;
 	skb = alloc_skb(rx_size, GFP_ATOMIC);
@@ -153,25 +159,34 @@ void i2400ms_rx(struct i2400ms *i2400ms)
 	}
 
 	rmb();	/* make sure we get boot_mode from dev_reset_handle */
-	if (i2400m->boot_mode == 1) {
+	if (unlikely(i2400m->boot_mode == 1)) {
 		spin_lock(&i2400m->rx_lock);
 		i2400ms->bm_ack_size = rx_size;
 		spin_unlock(&i2400m->rx_lock);
 		memcpy(i2400m->bm_ack_buf, skb->data, rx_size);
 		wake_up(&i2400ms->bm_wfa_wq);
-		dev_err(dev, "RX: SDIO boot mode message\n");
+		d_printf(5, dev, "RX: SDIO boot mode message\n");
 		kfree_skb(skb);
-	} else if (unlikely(!memcmp(skb->data, i2400m_NBOOT_BARKER,
-				    sizeof(i2400m_NBOOT_BARKER))
-			    || !memcmp(skb->data, i2400m_SBOOT_BARKER,
-				       sizeof(i2400m_SBOOT_BARKER)))) {
-		ret = i2400m_dev_reset_handle(i2400m);
+		goto out;
+	}
+	ret = -EIO;
+	if (unlikely(rx_size < sizeof(__le32))) {
+		dev_err(dev, "HW BUG? only %zu bytes received\n", rx_size);
+		goto error_bad_size;
+	}
+	if (likely(i2400m_is_d2h_barker(skb->data))) {
+		skb_put(skb, rx_size);
+		i2400m_rx(i2400m, skb);
+	} else if (unlikely(i2400m_is_boot_barker(i2400m,
+						  skb->data, rx_size))) {
+		ret = i2400m_dev_reset_handle(i2400m, "device rebooted");
 		dev_err(dev, "RX: SDIO reboot barker\n");
 		kfree_skb(skb);
 	} else {
-		skb_put(skb, rx_size);
-		i2400m_rx(i2400m, skb);
+		i2400m_unknown_barker(i2400m, skb->data, rx_size);
+		kfree_skb(skb);
 	}
+out:
 	d_fnend(7, dev, "(i2400ms %p) = void\n", i2400ms);
 	return;
 
@@ -179,6 +194,7 @@ void i2400ms_rx(struct i2400ms *i2400ms)
 	kfree_skb(skb);
 error_alloc_skb:
 error_get_size:
+error_bad_size:
 	d_fnend(7, dev, "(i2400ms %p) = %d\n", i2400ms, ret);
 	return;
 }
@@ -209,7 +225,6 @@ void i2400ms_irq(struct sdio_func *func)
 		dev_err(dev, "RX: BUG? got IRQ but no interrupt ready?\n");
 		goto error_no_irq;
 	}
-	sdio_writeb(func, 1, I2400MS_INTR_CLEAR_ADDR, &ret);
 	i2400ms_rx(i2400ms);
 error_no_irq:
 	d_fnend(6, dev, "(i2400ms %p) = void\n", i2400ms);
@@ -234,6 +249,13 @@ int i2400ms_rx_setup(struct i2400ms *i2400ms)
 	init_waitqueue_head(&i2400ms->bm_wfa_wq);
 	spin_lock(&i2400m->rx_lock);
 	i2400ms->bm_wait_result = -EINPROGRESS;
+	/*
+	 * Before we are about to enable the RX interrupt, make sure
+	 * bm_ack_size is cleared to -EINPROGRESS which indicates
+	 * no RX interrupt happened yet or the previous interrupt
+	 * has been handled, we are ready to take the new interrupt
+	 */
+	i2400ms->bm_ack_size = -EINPROGRESS;
 	spin_unlock(&i2400m->rx_lock);
 
 	sdio_claim_host(func);

drivers/net/wimax/i2400m/sdio-tx.c

@@ -149,5 +149,8 @@ int i2400ms_tx_setup(struct i2400ms *i2400ms)
 
 void i2400ms_tx_release(struct i2400ms *i2400ms)
 {
-	destroy_workqueue(i2400ms->tx_workqueue);
+	if (i2400ms->tx_workqueue) {
+		destroy_workqueue(i2400ms->tx_workqueue);
+		i2400ms->tx_workqueue = NULL;
+	}
 }

drivers/net/wimax/i2400m/sdio.c

@@ -43,18 +43,9 @@
  *     i2400m_release()
  *     free_netdev(net_dev)
  *
- * i2400ms_bus_reset()            Called by i2400m->bus_reset
+ * i2400ms_bus_reset()            Called by i2400m_reset
  *   __i2400ms_reset()
  *     __i2400ms_send_barker()
- *
- * i2400ms_bus_dev_start()        Called by i2400m_dev_start() [who is
- *   i2400ms_tx_setup()           called by i2400m_setup()]
- *   i2400ms_rx_setup()
- *
- * i2400ms_bus_dev_stop()         Called by i2400m_dev_stop() [who is
- *   i2400ms_rx_release()         is called by i2400m_release()]
- *   i2400ms_tx_release()
- *
  */
 
 #include <linux/debugfs.h>
@@ -71,6 +62,14 @@
 static int ioe_timeout = 2;
 module_param(ioe_timeout, int, 0);
 
+static char i2400ms_debug_params[128];
+module_param_string(debug, i2400ms_debug_params, sizeof(i2400ms_debug_params),
+		    0644);
+MODULE_PARM_DESC(debug,
+		 "String of space-separated NAME:VALUE pairs, where NAMEs "
+		 "are the different debug submodules and VALUE are the "
+		 "initial debug value to set.");
+
 /* Our firmware file name list */
 static const char *i2400ms_bus_fw_names[] = {
 #define I2400MS_FW_FILE_NAME "i2400m-fw-sdio-1.3.sbcf"
@@ -95,17 +94,24 @@ static const struct i2400m_poke_table i2400ms_pokes[] = {
  * when we ask it to explicitly doing). Tries until a timeout is
  * reached.
  *
+ * The @maxtries argument indicates how many times (at most) it should
+ * be tried to enable the function. 0 means forever. This acts along
+ * with the timeout (ie: it'll stop trying as soon as the maximum
+ * number of tries is reached _or_ as soon as the timeout is reached).
+ *
  * The reverse of this is...sdio_disable_function()
  *
  * Returns: 0 if the SDIO function was enabled, < 0 errno code on
  *     error (-ENODEV when it was unable to enable the function).
  */
 static
-int i2400ms_enable_function(struct sdio_func *func)
+int i2400ms_enable_function(struct i2400ms *i2400ms, unsigned maxtries)
 {
+	struct sdio_func *func = i2400ms->func;
 	u64 timeout;
 	int err;
 	struct device *dev = &func->dev;
+	unsigned tries = 0;
 
 	d_fnstart(3, dev, "(func %p)\n", func);
 	/* Setup timeout (FIXME: This needs to read the CIS table to
@@ -115,6 +121,14 @@ int i2400ms_enable_function(struct sdio_func *func)
 	err = -ENODEV;
 	while (err != 0 && time_before64(get_jiffies_64(), timeout)) {
 		sdio_claim_host(func);
+		/*
+		 * There is a sillicon bug on the IWMC3200, where the
+		 * IOE timeout will cause problems on Moorestown
+		 * platforms (system hang). We explicitly overwrite
+		 * func->enable_timeout here to work around the issue.
+		 */
+		if (i2400ms->iwmc3200)
+			func->enable_timeout = IWMC3200_IOR_TIMEOUT;
 		err = sdio_enable_func(func);
 		if (0 == err) {
 			sdio_release_host(func);
@@ -122,8 +136,11 @@ int i2400ms_enable_function(struct sdio_func *func)
 			goto function_enabled;
 		}
 		d_printf(2, dev, "SDIO function failed to enable: %d\n", err);
-		sdio_disable_func(func);
 		sdio_release_host(func);
+		if (maxtries > 0 && ++tries >= maxtries) {
+			err = -ETIME;
+			break;
+		}
 		msleep(I2400MS_INIT_SLEEP_INTERVAL);
 	}
 	/* If timed out, device is not there yet -- get -ENODEV so
@@ -140,46 +157,99 @@ int i2400ms_enable_function(struct sdio_func *func)
 
 
 /*
- * Setup driver resources needed to communicate with the device
+ * Setup minimal device communication infrastructure needed to at
+ * least be able to update the firmware.
  *
- * The fw needs some time to settle, and it was just uploaded,
- * so give it a break first. I'd prefer to just wait for the device to
- * send something, but seems the poking we do to enable SDIO stuff
- * interferes with it, so just give it a break before starting...
+ * Note the ugly trick: if we are in the probe path
+ * (i2400ms->debugfs_dentry == NULL), we only retry function
+ * enablement one, to avoid racing with the iwmc3200 top controller.
  */
 static
-int i2400ms_bus_dev_start(struct i2400m *i2400m)
+int i2400ms_bus_setup(struct i2400m *i2400m)
 {
 	int result;
-	struct i2400ms *i2400ms = container_of(i2400m, struct i2400ms, i2400m);
+	struct i2400ms *i2400ms =
+		container_of(i2400m, struct i2400ms, i2400m);
+	struct device *dev = i2400m_dev(i2400m);
 	struct sdio_func *func = i2400ms->func;
-	struct device *dev = &func->dev;
+	int retries;
+
+	sdio_claim_host(func);
+	result = sdio_set_block_size(func, I2400MS_BLK_SIZE);
+	sdio_release_host(func);
+	if (result < 0) {
+		dev_err(dev, "Failed to set block size: %d\n", result);
+		goto error_set_blk_size;
+	}
+
+	if (i2400ms->iwmc3200 && i2400ms->debugfs_dentry == NULL)
+		retries = 1;
+	else
+		retries = 0;
+	result = i2400ms_enable_function(i2400ms, retries);
+	if (result < 0) {
+		dev_err(dev, "Cannot enable SDIO function: %d\n", result);
+		goto error_func_enable;
+	}
 
-	d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
-	msleep(200);
 	result = i2400ms_tx_setup(i2400ms);
 	if (result < 0)
 		goto error_tx_setup;
-	d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, result);
-	return result;
+	result = i2400ms_rx_setup(i2400ms);
+	if (result < 0)
+		goto error_rx_setup;
+	return 0;
 
-error_tx_setup:
+error_rx_setup:
 	i2400ms_tx_release(i2400ms);
-	d_fnend(3, dev, "(i2400m %p) = void\n", i2400m);
+error_tx_setup:
+	sdio_claim_host(func);
+	sdio_disable_func(func);
+	sdio_release_host(func);
+error_func_enable:
+error_set_blk_size:
 	return result;
 }
 
 
+/*
+ * Tear down minimal device communication infrastructure needed to at
+ * least be able to update the firmware.
+ */
+static
+void i2400ms_bus_release(struct i2400m *i2400m)
+{
+	struct i2400ms *i2400ms =
+		container_of(i2400m, struct i2400ms, i2400m);
+	struct sdio_func *func = i2400ms->func;
+
+	i2400ms_rx_release(i2400ms);
+	i2400ms_tx_release(i2400ms);
+	sdio_claim_host(func);
+	sdio_disable_func(func);
+	sdio_release_host(func);
+}
+
+
+/*
+ * Setup driver resources needed to communicate with the device
+ *
+ * The fw needs some time to settle, and it was just uploaded,
+ * so give it a break first. I'd prefer to just wait for the device to
+ * send something, but seems the poking we do to enable SDIO stuff
+ * interferes with it, so just give it a break before starting...
+ */
 static
-void i2400ms_bus_dev_stop(struct i2400m *i2400m)
+int i2400ms_bus_dev_start(struct i2400m *i2400m)
 {
 	struct i2400ms *i2400ms = container_of(i2400m, struct i2400ms, i2400m);
 	struct sdio_func *func = i2400ms->func;
 	struct device *dev = &func->dev;
 
 	d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
-	i2400ms_tx_release(i2400ms);
-	d_fnend(3, dev, "(i2400m %p) = void\n", i2400m);
+	msleep(200);
+	d_fnend(3, dev, "(i2400m %p) = %d\n", i2400m, 0);
+	return 0;
 }
 
 
@@ -233,18 +303,17 @@ int __i2400ms_send_barker(struct i2400ms *i2400ms,
  * Warm reset:
  *
  * The device will be fully reset internally, but won't be
- * disconnected from the USB bus (so no reenumeration will
+ * disconnected from the bus (so no reenumeration will
  * happen). Firmware upload will be neccessary.
  *
- * The device will send a reboot barker in the notification endpoint
- * that will trigger the driver to reinitialize the state
- * automatically from notif.c:i2400m_notification_grok() into
- * i2400m_dev_bootstrap_delayed().
+ * The device will send a reboot barker that will trigger the driver
+ * to reinitialize the state via __i2400m_dev_reset_handle.
  *
- * Cold and bus (USB) reset:
+ *
+ * Cold and bus reset:
  *
  * The device will be fully reset internally, disconnected from the
- * USB bus an a reenumeration will happen. Firmware upload will be
+ * bus an a reenumeration will happen. Firmware upload will be
  * neccessary. Thus, we don't do any locking or struct
  * reinitialization, as we are going to be fully disconnected and
  * reenumerated.
@@ -283,25 +352,13 @@ int i2400ms_bus_reset(struct i2400m *i2400m, enum i2400m_reset_type rt)
 					       sizeof(i2400m_COLD_BOOT_BARKER));
 	else if (rt == I2400M_RT_BUS) {
 do_bus_reset:
-		/* call netif_tx_disable() before sending IOE disable,
-		 * so that all the tx from network layer are stopped
-		 * while IOE is being reset. Make sure it is called
-		 * only after register_netdev() was issued.
-		 */
-		if (i2400m->wimax_dev.net_dev->reg_state == NETREG_REGISTERED)
-			netif_tx_disable(i2400m->wimax_dev.net_dev);
 
-		i2400ms_rx_release(i2400ms);
-		sdio_claim_host(i2400ms->func);
-		sdio_disable_func(i2400ms->func);
-		sdio_release_host(i2400ms->func);
+		i2400ms_bus_release(i2400m);
 
 		/* Wait for the device to settle */
 		msleep(40);
 
-		result = i2400ms_enable_function(i2400ms->func);
-		if (result >= 0)
-			i2400ms_rx_setup(i2400ms);
+		result =  i2400ms_bus_setup(i2400m);
 	} else
 		BUG();
 	if (result < 0 && rt != I2400M_RT_BUS) {
@@ -350,7 +407,7 @@ int i2400ms_debugfs_add(struct i2400ms *i2400ms)
 	int result;
 	struct dentry *dentry = i2400ms->i2400m.wimax_dev.debugfs_dentry;
 
-	dentry = debugfs_create_dir("i2400m-usb", dentry);
+	dentry = debugfs_create_dir("i2400m-sdio", dentry);
 	result = PTR_ERR(dentry);
 	if (IS_ERR(dentry)) {
 		if (result == -ENODEV)
@@ -367,6 +424,7 @@ int i2400ms_debugfs_add(struct i2400ms *i2400ms)
 
 error:
 	debugfs_remove_recursive(i2400ms->debugfs_dentry);
+	i2400ms->debugfs_dentry = NULL;
 	return result;
 }
 
@@ -425,37 +483,30 @@ int i2400ms_probe(struct sdio_func *func,
 
 	i2400m->bus_tx_block_size = I2400MS_BLK_SIZE;
 	i2400m->bus_pl_size_max = I2400MS_PL_SIZE_MAX;
+	i2400m->bus_setup = i2400ms_bus_setup;
 	i2400m->bus_dev_start = i2400ms_bus_dev_start;
-	i2400m->bus_dev_stop = i2400ms_bus_dev_stop;
+	i2400m->bus_dev_stop = NULL;
+	i2400m->bus_release = i2400ms_bus_release;
 	i2400m->bus_tx_kick = i2400ms_bus_tx_kick;
 	i2400m->bus_reset = i2400ms_bus_reset;
 	/* The iwmc3200-wimax sometimes requires the driver to try
 	 * hard when we paint it into a corner. */
-	i2400m->bus_bm_retries = I3200_BOOT_RETRIES;
+	i2400m->bus_bm_retries = I2400M_SDIO_BOOT_RETRIES;
 	i2400m->bus_bm_cmd_send = i2400ms_bus_bm_cmd_send;
 	i2400m->bus_bm_wait_for_ack = i2400ms_bus_bm_wait_for_ack;
 	i2400m->bus_fw_names = i2400ms_bus_fw_names;
 	i2400m->bus_bm_mac_addr_impaired = 1;
 	i2400m->bus_bm_pokes_table = &i2400ms_pokes[0];
 
-	sdio_claim_host(func);
-	result = sdio_set_block_size(func, I2400MS_BLK_SIZE);
-	sdio_release_host(func);
-	if (result < 0) {
-		dev_err(dev, "Failed to set block size: %d\n", result);
-		goto error_set_blk_size;
-	}
-
-	result = i2400ms_enable_function(i2400ms->func);
-	if (result < 0) {
-		dev_err(dev, "Cannot enable SDIO function: %d\n", result);
-		goto error_func_enable;
+	switch (func->device) {
+	case SDIO_DEVICE_ID_INTEL_IWMC3200WIMAX:
+	case SDIO_DEVICE_ID_INTEL_IWMC3200WIMAX_2G5:
+		i2400ms->iwmc3200 = 1;
+		break;
+	default:
+		i2400ms->iwmc3200 = 0;
 	}
 
-	result = i2400ms_rx_setup(i2400ms);
-	if (result < 0)
-		goto error_rx_setup;
-
 	result = i2400m_setup(i2400m, I2400M_BRI_NO_REBOOT);
 	if (result < 0) {
 		dev_err(dev, "cannot setup device: %d\n", result);
@@ -473,13 +524,6 @@ int i2400ms_probe(struct sdio_func *func,
 error_debugfs_add:
 	i2400m_release(i2400m);
 error_setup:
-	i2400ms_rx_release(i2400ms);
-error_rx_setup:
-	sdio_claim_host(func);
-	sdio_disable_func(func);
-	sdio_release_host(func);
-error_func_enable:
-error_set_blk_size:
 	sdio_set_drvdata(func, NULL);
 	free_netdev(net_dev);
 error_alloc_netdev:
@@ -497,12 +541,9 @@ void i2400ms_remove(struct sdio_func *func)
 
 	d_fnstart(3, dev, "SDIO func %p\n", func);
 	debugfs_remove_recursive(i2400ms->debugfs_dentry);
-	i2400ms_rx_release(i2400ms);
+	i2400ms->debugfs_dentry = NULL;
 	i2400m_release(i2400m);
 	sdio_set_drvdata(func, NULL);
-	sdio_claim_host(func);
-	sdio_disable_func(func);
-	sdio_release_host(func);
 	free_netdev(net_dev);
 	d_fnend(3, dev, "SDIO func %p\n", func);
 }
@@ -512,6 +553,8 @@ const struct sdio_device_id i2400ms_sdio_ids[] = {
 	/* Intel: i2400m WiMAX (iwmc3200) over SDIO */
 	{ SDIO_DEVICE(SDIO_VENDOR_ID_INTEL,
 		      SDIO_DEVICE_ID_INTEL_IWMC3200WIMAX) },
+	{ SDIO_DEVICE(SDIO_VENDOR_ID_INTEL,
+		      SDIO_DEVICE_ID_INTEL_IWMC3200WIMAX_2G5) },
 	{ /* end: all zeroes */ },
 };
 MODULE_DEVICE_TABLE(sdio, i2400ms_sdio_ids);
@@ -529,6 +572,8 @@ struct sdio_driver i2400m_sdio_driver = {
 static
 int __init i2400ms_driver_init(void)
 {
+	d_parse_params(D_LEVEL, D_LEVEL_SIZE, i2400ms_debug_params,
+		       "i2400m_sdio.debug");
 	return sdio_register_driver(&i2400m_sdio_driver);
 }
 module_init(i2400ms_driver_init);

drivers/net/wimax/i2400m/tx.c

@@ -310,7 +310,7 @@ size_t __i2400m_tx_tail_room(struct i2400m *i2400m)
 	size_t tail_room;
 	size_t tx_in;
 
-	if (unlikely(i2400m->tx_in) == 0)
+	if (unlikely(i2400m->tx_in == 0))
 		return I2400M_TX_BUF_SIZE;
 	tx_in = i2400m->tx_in % I2400M_TX_BUF_SIZE;
 	tail_room = I2400M_TX_BUF_SIZE - tx_in;
@@ -642,6 +642,9 @@ int i2400m_tx(struct i2400m *i2400m, const void *buf, size_t buf_len,
 	 * current one is out of payload slots or we have a singleton,
 	 * close it and start a new one */
 	spin_lock_irqsave(&i2400m->tx_lock, flags);
+	result = -ESHUTDOWN;
+	if (i2400m->tx_buf == NULL)
+		goto error_tx_new;
 try_new:
 	if (unlikely(i2400m->tx_msg == NULL))
 		i2400m_tx_new(i2400m);
@@ -697,7 +700,10 @@ int i2400m_tx(struct i2400m *i2400m, const void *buf, size_t buf_len,
 	}
 error_tx_new:
 	spin_unlock_irqrestore(&i2400m->tx_lock, flags);
-	i2400m->bus_tx_kick(i2400m);	/* always kick, might free up space */
+	/* kick in most cases, except when the TX subsys is down, as
+	 * it might free space */
+	if (likely(result != -ESHUTDOWN))
+		i2400m->bus_tx_kick(i2400m);
 	d_fnend(3, dev, "(i2400m %p skb %p [%zu bytes] pt %u) = %d\n",
 		i2400m, buf, buf_len, pl_type, result);
 	return result;
@@ -740,6 +746,9 @@ struct i2400m_msg_hdr *i2400m_tx_msg_get(struct i2400m *i2400m,
 
 	d_fnstart(3, dev, "(i2400m %p bus_size %p)\n", i2400m, bus_size);
 	spin_lock_irqsave(&i2400m->tx_lock, flags);
+	tx_msg_moved = NULL;
+	if (i2400m->tx_buf == NULL)
+		goto out_unlock;
 skip:
 	tx_msg_moved = NULL;
 	if (i2400m->tx_in == i2400m->tx_out) {	/* Empty FIFO? */
@@ -829,6 +838,8 @@ void i2400m_tx_msg_sent(struct i2400m *i2400m)
 
 	d_fnstart(3, dev, "(i2400m %p)\n", i2400m);
 	spin_lock_irqsave(&i2400m->tx_lock, flags);
+	if (i2400m->tx_buf == NULL)
+		goto out_unlock;
 	i2400m->tx_out += i2400m->tx_msg_size;
 	d_printf(2, dev, "TX: sent %zu b\n", (size_t) i2400m->tx_msg_size);
 	i2400m->tx_msg_size = 0;
@@ -837,6 +848,7 @@ void i2400m_tx_msg_sent(struct i2400m *i2400m)
 	n = i2400m->tx_out / I2400M_TX_BUF_SIZE;
 	i2400m->tx_out %= I2400M_TX_BUF_SIZE;
 	i2400m->tx_in -= n * I2400M_TX_BUF_SIZE;
+out_unlock:
 	spin_unlock_irqrestore(&i2400m->tx_lock, flags);
 	d_fnend(3, dev, "(i2400m %p) = void\n", i2400m);
 }
@@ -876,5 +888,9 @@ int i2400m_tx_setup(struct i2400m *i2400m)
  */
 void i2400m_tx_release(struct i2400m *i2400m)
 {
+	unsigned long flags;
+	spin_lock_irqsave(&i2400m->tx_lock, flags);
 	kfree(i2400m->tx_buf);
+	i2400m->tx_buf = NULL;
+	spin_unlock_irqrestore(&i2400m->tx_lock, flags);
 }

drivers/net/wimax/i2400m/usb-fw.c

@@ -99,10 +99,10 @@ ssize_t i2400mu_tx_bulk_out(struct i2400mu *i2400mu, void *buf, size_t buf_size)
 		dev_err(dev, "BM-CMD: can't get autopm: %d\n", result);
 		do_autopm = 0;
 	}
-	epd = usb_get_epd(i2400mu->usb_iface, I2400MU_EP_BULK_OUT);
+	epd = usb_get_epd(i2400mu->usb_iface, i2400mu->endpoint_cfg.bulk_out);
 	pipe = usb_sndbulkpipe(i2400mu->usb_dev, epd->bEndpointAddress);
 retry:
-	result = usb_bulk_msg(i2400mu->usb_dev, pipe, buf, buf_size, &len, HZ);
+	result = usb_bulk_msg(i2400mu->usb_dev, pipe, buf, buf_size, &len, 200);
 	switch (result) {
 	case 0:
 		if (len != buf_size) {
@@ -113,6 +113,28 @@ ssize_t i2400mu_tx_bulk_out(struct i2400mu *i2400mu, void *buf, size_t buf_size)
 		}
 		result = len;
 		break;
+	case -EPIPE:
+		/*
+		 * Stall -- maybe the device is choking with our
+		 * requests. Clear it and give it some time. If they
+		 * happen to often, it might be another symptom, so we
+		 * reset.
+		 *
+		 * No error handling for usb_clear_halt(0; if it
+		 * works, the retry works; if it fails, this switch
+		 * does the error handling for us.
+		 */
+		if (edc_inc(&i2400mu->urb_edc,
+			    10 * EDC_MAX_ERRORS, EDC_ERROR_TIMEFRAME)) {
+			dev_err(dev, "BM-CMD: too many stalls in "
+				"URB; resetting device\n");
+			usb_queue_reset_device(i2400mu->usb_iface);
+			/* fallthrough */
+		} else {
+			usb_clear_halt(i2400mu->usb_dev, pipe);
+			msleep(10);	/* give the device some time */
+			goto retry;
+		}
 	case -EINVAL:			/* while removing driver */
 	case -ENODEV:			/* dev disconnect ... */
 	case -ENOENT:			/* just ignore it */
@@ -135,7 +157,6 @@ ssize_t i2400mu_tx_bulk_out(struct i2400mu *i2400mu, void *buf, size_t buf_size)
 			result);
 		goto retry;
 	}
-	result = len;
 	if (do_autopm)
 		usb_autopm_put_interface(i2400mu->usb_iface);
 	return result;
@@ -172,7 +193,8 @@ ssize_t i2400mu_bus_bm_cmd_send(struct i2400m *i2400m,
 	result = -E2BIG;
 	if (cmd_size > I2400M_BM_CMD_BUF_SIZE)
 		goto error_too_big;
-	memcpy(i2400m->bm_cmd_buf, _cmd, cmd_size);
+	if (_cmd != i2400m->bm_cmd_buf)
+		memmove(i2400m->bm_cmd_buf, _cmd, cmd_size);
 	cmd = i2400m->bm_cmd_buf;
 	if (cmd_size_a > cmd_size)			/* Zero pad space */
 		memset(i2400m->bm_cmd_buf + cmd_size, 0, cmd_size_a - cmd_size);
@@ -226,7 +248,8 @@ int i2400mu_notif_submit(struct i2400mu *i2400mu, struct urb *urb,
 	struct usb_endpoint_descriptor *epd;
 	int pipe;
 
-	epd = usb_get_epd(i2400mu->usb_iface, I2400MU_EP_NOTIFICATION);
+	epd = usb_get_epd(i2400mu->usb_iface,
+			  i2400mu->endpoint_cfg.notification);
 	pipe = usb_rcvintpipe(i2400mu->usb_dev, epd->bEndpointAddress);
 	usb_fill_int_urb(urb, i2400mu->usb_dev, pipe,
 			 i2400m->bm_ack_buf, I2400M_BM_ACK_BUF_SIZE,
@@ -328,8 +351,8 @@ ssize_t i2400mu_bus_bm_wait_for_ack(struct i2400m *i2400m,
 out:
 	if (do_autopm)
 		usb_autopm_put_interface(i2400mu->usb_iface);
-	d_fnend(8, dev, "(i2400m %p ack %p size %zu) = %zd\n",
-		i2400m, ack, ack_size, result);
+	d_fnend(8, dev, "(i2400m %p ack %p size %zu) = %ld\n",
+		i2400m, ack, ack_size, (long) result);
 	return result;
 
 error_exceeded:

drivers/net/wimax/i2400m/usb-notif.c

@@ -51,6 +51,7 @@
  *
  * i2400mu_usb_notification_cb()	Called when a URB is ready
  *   i2400mu_notif_grok()
+ *     i2400m_is_boot_barker()
  *     i2400m_dev_reset_handle()
  *     i2400mu_rx_kick()
  */
@@ -87,32 +88,21 @@ int i2400mu_notification_grok(struct i2400mu *i2400mu, const void *buf,
 	d_fnstart(4, dev, "(i2400m %p buf %p buf_len %zu)\n",
 		  i2400mu, buf, buf_len);
 	ret = -EIO;
-	if (buf_len < sizeof(i2400m_NBOOT_BARKER))
+	if (buf_len < sizeof(i2400m_ZERO_BARKER))
 		/* Not a bug, just ignore */
 		goto error_bad_size;
-	if (!memcmp(i2400m_NBOOT_BARKER, buf, sizeof(i2400m_NBOOT_BARKER))
-	    || !memcmp(i2400m_SBOOT_BARKER, buf, sizeof(i2400m_SBOOT_BARKER)))
-		ret = i2400m_dev_reset_handle(i2400m);
-	else if (!memcmp(i2400m_ZERO_BARKER, buf, sizeof(i2400m_ZERO_BARKER))) {
+	ret = 0;
+	if (!memcmp(i2400m_ZERO_BARKER, buf, sizeof(i2400m_ZERO_BARKER))) {
 		i2400mu_rx_kick(i2400mu);
-		ret = 0;
-	} else {	/* Unknown or unexpected data in the notif message */
-		char prefix[64];
-		ret = -EIO;
-		dev_err(dev, "HW BUG? Unknown/unexpected data in notification "
-			"message (%zu bytes)\n", buf_len);
-		snprintf(prefix, sizeof(prefix), "%s %s: ",
-			 dev_driver_string(dev), dev_name(dev));
-		if (buf_len > 64) {
-			print_hex_dump(KERN_ERR, prefix, DUMP_PREFIX_OFFSET,
-				       8, 4, buf, 64, 0);
-			printk(KERN_ERR "%s... (only first 64 bytes "
-			       "dumped)\n", prefix);
-		} else
-			print_hex_dump(KERN_ERR, prefix, DUMP_PREFIX_OFFSET,
-				       8, 4, buf, buf_len, 0);
+		goto out;
 	}
+	ret = i2400m_is_boot_barker(i2400m, buf, buf_len);
+	if (unlikely(ret >= 0))
+		ret = i2400m_dev_reset_handle(i2400m, "device rebooted");
+	else	/* Unknown or unexpected data in the notif message */
+		i2400m_unknown_barker(i2400m, buf, buf_len);
 error_bad_size:
+out:
 	d_fnend(4, dev, "(i2400m %p buf %p buf_len %zu) = %d\n",
 		i2400mu, buf, buf_len, ret);
 	return ret;
@@ -220,7 +210,8 @@ int i2400mu_notification_setup(struct i2400mu *i2400mu)
 		dev_err(dev, "notification: cannot allocate URB\n");
 		goto error_alloc_urb;
 	}
-	epd = usb_get_epd(i2400mu->usb_iface, I2400MU_EP_NOTIFICATION);
+	epd = usb_get_epd(i2400mu->usb_iface,
+			  i2400mu->endpoint_cfg.notification);
 	usb_pipe = usb_rcvintpipe(i2400mu->usb_dev, epd->bEndpointAddress);
 	usb_fill_int_urb(i2400mu->notif_urb, i2400mu->usb_dev, usb_pipe,
 			 buf, I2400MU_MAX_NOTIFICATION_LEN,

drivers/net/wimax/i2400m/usb-rx.c

@@ -204,7 +204,7 @@ struct sk_buff *i2400mu_rx(struct i2400mu *i2400mu, struct sk_buff *rx_skb)
 		dev_err(dev, "RX: can't get autopm: %d\n", result);
 		do_autopm = 0;
 	}
-	epd = usb_get_epd(i2400mu->usb_iface, I2400MU_EP_BULK_IN);
+	epd = usb_get_epd(i2400mu->usb_iface, i2400mu->endpoint_cfg.bulk_in);
 	usb_pipe = usb_rcvbulkpipe(i2400mu->usb_dev, epd->bEndpointAddress);
 retry:
 	rx_size = skb_end_pointer(rx_skb) - rx_skb->data - rx_skb->len;
@@ -214,7 +214,7 @@ struct sk_buff *i2400mu_rx(struct i2400mu *i2400mu, struct sk_buff *rx_skb)
 	}
 	result = usb_bulk_msg(
 		i2400mu->usb_dev, usb_pipe, rx_skb->data + rx_skb->len,
-		rx_size, &read_size, HZ);
+		rx_size, &read_size, 200);
 	usb_mark_last_busy(i2400mu->usb_dev);
 	switch (result) {
 	case 0:
@@ -222,6 +222,26 @@ struct sk_buff *i2400mu_rx(struct i2400mu *i2400mu, struct sk_buff *rx_skb)
 			goto retry;	/* ZLP, just resubmit */
 		skb_put(rx_skb, read_size);
 		break;
+	case -EPIPE:
+		/*
+		 * Stall -- maybe the device is choking with our
+		 * requests. Clear it and give it some time. If they
+		 * happen to often, it might be another symptom, so we
+		 * reset.
+		 *
+		 * No error handling for usb_clear_halt(0; if it
+		 * works, the retry works; if it fails, this switch
+		 * does the error handling for us.
+		 */
+		if (edc_inc(&i2400mu->urb_edc,
+			    10 * EDC_MAX_ERRORS, EDC_ERROR_TIMEFRAME)) {
+			dev_err(dev, "BM-CMD: too many stalls in "
+				"URB; resetting device\n");
+			goto do_reset;
+		}
+		usb_clear_halt(i2400mu->usb_dev, usb_pipe);
+		msleep(10);	/* give the device some time */
+		goto retry;
 	case -EINVAL:			/* while removing driver */
 	case -ENODEV:			/* dev disconnect ... */
 	case -ENOENT:			/* just ignore it */
@@ -283,6 +303,7 @@ struct sk_buff *i2400mu_rx(struct i2400mu *i2400mu, struct sk_buff *rx_skb)
 error_reset:
 	dev_err(dev, "RX: maximum errors in URB exceeded; "
 		"resetting device\n");
+do_reset:
 	usb_queue_reset_device(i2400mu->usb_iface);
 	rx_skb = ERR_PTR(result);
 	goto out;
@@ -316,10 +337,15 @@ int i2400mu_rxd(void *_i2400mu)
 	size_t pending;
 	int rx_size;
 	struct sk_buff *rx_skb;
+	unsigned long flags;
 
 	d_fnstart(4, dev, "(i2400mu %p)\n", i2400mu);
+	spin_lock_irqsave(&i2400m->rx_lock, flags);
+	BUG_ON(i2400mu->rx_kthread != NULL);
+	i2400mu->rx_kthread = current;
+	spin_unlock_irqrestore(&i2400m->rx_lock, flags);
 	while (1) {
-		d_printf(2, dev, "TX: waiting for messages\n");
+		d_printf(2, dev, "RX: waiting for messages\n");
 		pending = 0;
 		wait_event_interruptible(
 			i2400mu->rx_wq,
@@ -367,6 +393,9 @@ int i2400mu_rxd(void *_i2400mu)
 	}
 	result = 0;
 out:
+	spin_lock_irqsave(&i2400m->rx_lock, flags);
+	i2400mu->rx_kthread = NULL;
+	spin_unlock_irqrestore(&i2400m->rx_lock, flags);
 	d_fnend(4, dev, "(i2400mu %p) = %d\n", i2400mu, result);
 	return result;
 
@@ -403,18 +432,33 @@ int i2400mu_rx_setup(struct i2400mu *i2400mu)
 	struct i2400m *i2400m = &i2400mu->i2400m;
 	struct device *dev = &i2400mu->usb_iface->dev;
 	struct wimax_dev *wimax_dev = &i2400m->wimax_dev;
+	struct task_struct *kthread;
 
-	i2400mu->rx_kthread = kthread_run(i2400mu_rxd, i2400mu, "%s-rx",
-					  wimax_dev->name);
-	if (IS_ERR(i2400mu->rx_kthread)) {
-		result = PTR_ERR(i2400mu->rx_kthread);
+	kthread = kthread_run(i2400mu_rxd, i2400mu, "%s-rx",
+			      wimax_dev->name);
+	/* the kthread function sets i2400mu->rx_thread */
+	if (IS_ERR(kthread)) {
+		result = PTR_ERR(kthread);
 		dev_err(dev, "RX: cannot start thread: %d\n", result);
 	}
 	return result;
 }
 
+
 void i2400mu_rx_release(struct i2400mu *i2400mu)
 {
-	kthread_stop(i2400mu->rx_kthread);
+	unsigned long flags;
+	struct i2400m *i2400m = &i2400mu->i2400m;
+	struct device *dev = i2400m_dev(i2400m);
+	struct task_struct *kthread;
+
+	spin_lock_irqsave(&i2400m->rx_lock, flags);
+	kthread = i2400mu->rx_kthread;
+	i2400mu->rx_kthread = NULL;
+	spin_unlock_irqrestore(&i2400m->rx_lock, flags);
+	if (kthread)
+		kthread_stop(kthread);
+	else
+		d_printf(1, dev, "RX: kthread had already exited\n");
 }
 

drivers/net/wimax/i2400m/usb-tx.c

@@ -101,11 +101,11 @@ int i2400mu_tx(struct i2400mu *i2400mu, struct i2400m_msg_hdr *tx_msg,
 		dev_err(dev, "TX: can't get autopm: %d\n", result);
 		do_autopm = 0;
 	}
-	epd = usb_get_epd(i2400mu->usb_iface, I2400MU_EP_BULK_OUT);
+	epd = usb_get_epd(i2400mu->usb_iface, i2400mu->endpoint_cfg.bulk_out);
 	usb_pipe = usb_sndbulkpipe(i2400mu->usb_dev, epd->bEndpointAddress);
 retry:
 	result = usb_bulk_msg(i2400mu->usb_dev, usb_pipe,
-			      tx_msg, tx_msg_size, &sent_size, HZ);
+			      tx_msg, tx_msg_size, &sent_size, 200);
 	usb_mark_last_busy(i2400mu->usb_dev);
 	switch (result) {
 	case 0:
@@ -115,6 +115,28 @@ int i2400mu_tx(struct i2400mu *i2400mu, struct i2400m_msg_hdr *tx_msg,
 			result = -EIO;
 		}
 		break;
+	case -EPIPE:
+		/*
+		 * Stall -- maybe the device is choking with our
+		 * requests. Clear it and give it some time. If they
+		 * happen to often, it might be another symptom, so we
+		 * reset.
+		 *
+		 * No error handling for usb_clear_halt(0; if it
+		 * works, the retry works; if it fails, this switch
+		 * does the error handling for us.
+		 */
+		if (edc_inc(&i2400mu->urb_edc,
+			    10 * EDC_MAX_ERRORS, EDC_ERROR_TIMEFRAME)) {
+			dev_err(dev, "BM-CMD: too many stalls in "
+				"URB; resetting device\n");
+			usb_queue_reset_device(i2400mu->usb_iface);
+			/* fallthrough */
+		} else {
+			usb_clear_halt(i2400mu->usb_dev, usb_pipe);
+			msleep(10);	/* give the device some time */
+			goto retry;
+		}
 	case -EINVAL:			/* while removing driver */
 	case -ENODEV:			/* dev disconnect ... */
 	case -ENOENT:			/* just ignore it */
@@ -161,9 +183,15 @@ int i2400mu_txd(void *_i2400mu)
 	struct device *dev = &i2400mu->usb_iface->dev;
 	struct i2400m_msg_hdr *tx_msg;
 	size_t tx_msg_size;
+	unsigned long flags;
 
 	d_fnstart(4, dev, "(i2400mu %p)\n", i2400mu);
 
+	spin_lock_irqsave(&i2400m->tx_lock, flags);
+	BUG_ON(i2400mu->tx_kthread != NULL);
+	i2400mu->tx_kthread = current;
+	spin_unlock_irqrestore(&i2400m->tx_lock, flags);
+
 	while (1) {
 		d_printf(2, dev, "TX: waiting for messages\n");
 		tx_msg = NULL;
@@ -183,6 +211,11 @@ int i2400mu_txd(void *_i2400mu)
 		if (result < 0)
 			break;
 	}
+
+	spin_lock_irqsave(&i2400m->tx_lock, flags);
+	i2400mu->tx_kthread = NULL;
+	spin_unlock_irqrestore(&i2400m->tx_lock, flags);
+
 	d_fnend(4, dev, "(i2400mu %p) = %d\n", i2400mu, result);
 	return result;
 }
@@ -213,11 +246,13 @@ int i2400mu_tx_setup(struct i2400mu *i2400mu)
 	struct i2400m *i2400m = &i2400mu->i2400m;
 	struct device *dev = &i2400mu->usb_iface->dev;
 	struct wimax_dev *wimax_dev = &i2400m->wimax_dev;
+	struct task_struct *kthread;
 
-	i2400mu->tx_kthread = kthread_run(i2400mu_txd, i2400mu, "%s-tx",
-					  wimax_dev->name);
-	if (IS_ERR(i2400mu->tx_kthread)) {
-		result = PTR_ERR(i2400mu->tx_kthread);
+	kthread = kthread_run(i2400mu_txd, i2400mu, "%s-tx",
+			      wimax_dev->name);
+	/* the kthread function sets i2400mu->tx_thread */
+	if (IS_ERR(kthread)) {
+		result = PTR_ERR(kthread);
 		dev_err(dev, "TX: cannot start thread: %d\n", result);
 	}
 	return result;
@@ -225,5 +260,17 @@ int i2400mu_tx_setup(struct i2400mu *i2400mu)
 
 void i2400mu_tx_release(struct i2400mu *i2400mu)
 {
-	kthread_stop(i2400mu->tx_kthread);
+	unsigned long flags;
+	struct i2400m *i2400m = &i2400mu->i2400m;
+	struct device *dev = i2400m_dev(i2400m);
+	struct task_struct *kthread;
+
+	spin_lock_irqsave(&i2400m->tx_lock, flags);
+	kthread = i2400mu->tx_kthread;
+	i2400mu->tx_kthread = NULL;
+	spin_unlock_irqrestore(&i2400m->tx_lock, flags);
+	if (kthread)
+		kthread_stop(kthread);
+	else
+		d_printf(1, dev, "TX: kthread had already exited\n");
 }

drivers/net/wimax/i2400m/usb.c

@@ -58,7 +58,7 @@
  *   i2400mu_rx_release()
  *   i2400mu_tx_release()
  *
- * i2400mu_bus_reset()            Called by i2400m->bus_reset
+ * i2400mu_bus_reset()            Called by i2400m_reset
  *   __i2400mu_reset()
  *     __i2400mu_send_barker()
  *   usb_reset_device()
@@ -71,13 +71,25 @@
 #define D_SUBMODULE usb
 #include "usb-debug-levels.h"
 
+static char i2400mu_debug_params[128];
+module_param_string(debug, i2400mu_debug_params, sizeof(i2400mu_debug_params),
+		    0644);
+MODULE_PARM_DESC(debug,
+		 "String of space-separated NAME:VALUE pairs, where NAMEs "
+		 "are the different debug submodules and VALUE are the "
+		 "initial debug value to set.");
 
 /* Our firmware file name */
-static const char *i2400mu_bus_fw_names[] = {
+static const char *i2400mu_bus_fw_names_5x50[] = {
 #define I2400MU_FW_FILE_NAME_v1_4 "i2400m-fw-usb-1.4.sbcf"
 	I2400MU_FW_FILE_NAME_v1_4,
-#define I2400MU_FW_FILE_NAME_v1_3 "i2400m-fw-usb-1.3.sbcf"
-	I2400MU_FW_FILE_NAME_v1_3,
+	NULL,
+};
+
+
+static const char *i2400mu_bus_fw_names_6050[] = {
+#define I6050U_FW_FILE_NAME_v1_5 "i6050-fw-usb-1.5.sbcf"
+	I6050U_FW_FILE_NAME_v1_5,
 	NULL,
 };
 
@@ -160,14 +172,59 @@ int __i2400mu_send_barker(struct i2400mu *i2400mu,
 	epd = usb_get_epd(i2400mu->usb_iface, endpoint);
 	pipe = usb_sndbulkpipe(i2400mu->usb_dev, epd->bEndpointAddress);
 	memcpy(buffer, barker, barker_size);
+retry:
 	ret = usb_bulk_msg(i2400mu->usb_dev, pipe, buffer, barker_size,
-			   &actual_len, HZ);
-	if (ret < 0) {
-		if (ret != -EINVAL)
-			dev_err(dev, "E: barker error: %d\n", ret);
-	} else if (actual_len != barker_size) {
-		dev_err(dev, "E: only %d bytes transmitted\n", actual_len);
-		ret = -EIO;
+			   &actual_len, 200);
+	switch (ret) {
+	case 0:
+		if (actual_len != barker_size) {	/* Too short? drop it */
+			dev_err(dev, "E: %s: short write (%d B vs %zu "
+				"expected)\n",
+				__func__, actual_len, barker_size);
+			ret = -EIO;
+		}
+		break;
+	case -EPIPE:
+		/*
+		 * Stall -- maybe the device is choking with our
+		 * requests. Clear it and give it some time. If they
+		 * happen to often, it might be another symptom, so we
+		 * reset.
+		 *
+		 * No error handling for usb_clear_halt(0; if it
+		 * works, the retry works; if it fails, this switch
+		 * does the error handling for us.
+		 */
+		if (edc_inc(&i2400mu->urb_edc,
+			    10 * EDC_MAX_ERRORS, EDC_ERROR_TIMEFRAME)) {
+			dev_err(dev, "E: %s: too many stalls in "
+				"URB; resetting device\n", __func__);
+			usb_queue_reset_device(i2400mu->usb_iface);
+			/* fallthrough */
+		} else {
+			usb_clear_halt(i2400mu->usb_dev, pipe);
+			msleep(10);	/* give the device some time */
+			goto retry;
+		}
+	case -EINVAL:			/* while removing driver */
+	case -ENODEV:			/* dev disconnect ... */
+	case -ENOENT:			/* just ignore it */
+	case -ESHUTDOWN:		/* and exit */
+	case -ECONNRESET:
+		ret = -ESHUTDOWN;
+		break;
+	default:			/* Some error? */
+		if (edc_inc(&i2400mu->urb_edc,
+			    EDC_MAX_ERRORS, EDC_ERROR_TIMEFRAME)) {
+			dev_err(dev, "E: %s: maximum errors in URB "
+				"exceeded; resetting device\n",
+				__func__);
+			usb_queue_reset_device(i2400mu->usb_iface);
+		} else {
+			dev_warn(dev, "W: %s: cannot send URB: %d\n",
+				 __func__, ret);
+			goto retry;
+		}
 	}
 	kfree(buffer);
 error_kzalloc:
@@ -232,15 +289,16 @@ int i2400mu_bus_reset(struct i2400m *i2400m, enum i2400m_reset_type rt)
 
 	d_fnstart(3, dev, "(i2400m %p rt %u)\n", i2400m, rt);
 	if (rt == I2400M_RT_WARM)
-		result = __i2400mu_send_barker(i2400mu, i2400m_WARM_BOOT_BARKER,
-					       sizeof(i2400m_WARM_BOOT_BARKER),
-					       I2400MU_EP_BULK_OUT);
+		result = __i2400mu_send_barker(
+			i2400mu, i2400m_WARM_BOOT_BARKER,
+			sizeof(i2400m_WARM_BOOT_BARKER),
+			i2400mu->endpoint_cfg.bulk_out);
 	else if (rt == I2400M_RT_COLD)
-		result = __i2400mu_send_barker(i2400mu, i2400m_COLD_BOOT_BARKER,
-					       sizeof(i2400m_COLD_BOOT_BARKER),
-					       I2400MU_EP_RESET_COLD);
+		result = __i2400mu_send_barker(
+			i2400mu, i2400m_COLD_BOOT_BARKER,
+			sizeof(i2400m_COLD_BOOT_BARKER),
+			i2400mu->endpoint_cfg.reset_cold);
 	else if (rt == I2400M_RT_BUS) {
-do_bus_reset:
 		result = usb_reset_device(i2400mu->usb_dev);
 		switch (result) {
 		case 0:
@@ -248,7 +306,7 @@ int i2400mu_bus_reset(struct i2400m *i2400m, enum i2400m_reset_type rt)
 		case -ENODEV:
 		case -ENOENT:
 		case -ESHUTDOWN:
-			result = rt == I2400M_RT_WARM ? -ENODEV : 0;
+			result = 0;
 			break;	/* We assume the device is disconnected */
 		default:
 			dev_err(dev, "USB reset failed (%d), giving up!\n",
@@ -261,10 +319,17 @@ int i2400mu_bus_reset(struct i2400m *i2400m, enum i2400m_reset_type rt)
 	if (result < 0
 	    && result != -EINVAL	/* device is gone */
 	    && rt != I2400M_RT_BUS) {
+		/*
+		 * Things failed -- resort to lower level reset, that
+		 * we queue in another context; the reason for this is
+		 * that the pre and post reset functionality requires
+		 * the i2400m->init_mutex; RT_WARM and RT_COLD can
+		 * come from areas where i2400m->init_mutex is taken.
+		 */
 		dev_err(dev, "%s reset failed (%d); trying USB reset\n",
 			rt == I2400M_RT_WARM ? "warm" : "cold", result);
-		rt = I2400M_RT_BUS;
-		goto do_bus_reset;
+		usb_queue_reset_device(i2400mu->usb_iface);
+		result = -ENODEV;
 	}
 	d_fnend(3, dev, "(i2400m %p rt %u) = %d\n", i2400m, rt, result);
 	return result;
@@ -402,20 +467,33 @@ int i2400mu_probe(struct usb_interface *iface,
 
 	i2400m->bus_tx_block_size = I2400MU_BLK_SIZE;
 	i2400m->bus_pl_size_max = I2400MU_PL_SIZE_MAX;
+	i2400m->bus_setup = NULL;
 	i2400m->bus_dev_start = i2400mu_bus_dev_start;
 	i2400m->bus_dev_stop = i2400mu_bus_dev_stop;
+	i2400m->bus_release = NULL;
 	i2400m->bus_tx_kick = i2400mu_bus_tx_kick;
 	i2400m->bus_reset = i2400mu_bus_reset;
-	i2400m->bus_bm_retries = I2400M_BOOT_RETRIES;
+	i2400m->bus_bm_retries = I2400M_USB_BOOT_RETRIES;
 	i2400m->bus_bm_cmd_send = i2400mu_bus_bm_cmd_send;
 	i2400m->bus_bm_wait_for_ack = i2400mu_bus_bm_wait_for_ack;
-	i2400m->bus_fw_names = i2400mu_bus_fw_names;
 	i2400m->bus_bm_mac_addr_impaired = 0;
 
+	if (id->idProduct == USB_DEVICE_ID_I6050) {
+		i2400m->bus_fw_names = i2400mu_bus_fw_names_6050;
+		i2400mu->endpoint_cfg.bulk_out = 0;
+		i2400mu->endpoint_cfg.notification = 3;
+		i2400mu->endpoint_cfg.reset_cold = 2;
+		i2400mu->endpoint_cfg.bulk_in = 1;
+	} else {
+		i2400m->bus_fw_names = i2400mu_bus_fw_names_5x50;
+		i2400mu->endpoint_cfg.bulk_out = 0;
+		i2400mu->endpoint_cfg.notification = 1;
+		i2400mu->endpoint_cfg.reset_cold = 2;
+		i2400mu->endpoint_cfg.bulk_in = 3;
+	}
 #ifdef CONFIG_PM
 	iface->needs_remote_wakeup = 1;		/* autosuspend (15s delay) */
 	device_init_wakeup(dev, 1);
-	usb_autopm_enable(i2400mu->usb_iface);
 	usb_dev->autosuspend_delay = 15 * HZ;
 	usb_dev->autosuspend_disabled = 0;
 #endif
@@ -483,7 +561,10 @@ void i2400mu_disconnect(struct usb_interface *iface)
  * So at the end, the three cases require common handling.
  *
  * If at the time of this call the device's firmware is not loaded,
- * nothing has to be done.
+ * nothing has to be done. Note we can be "loose" about not reading
+ * i2400m->updown under i2400m->init_mutex. If it happens to change
+ * inmediately, other parts of the call flow will fail and effectively
+ * catch it.
  *
  * If the firmware is loaded, we need to:
  *
@@ -522,6 +603,7 @@ int i2400mu_suspend(struct usb_interface *iface, pm_message_t pm_msg)
 #endif
 
 	d_fnstart(3, dev, "(iface %p pm_msg %u)\n", iface, pm_msg.event);
+	rmb();		/* see i2400m->updown's documentation  */
 	if (i2400m->updown == 0)
 		goto no_firmware;
 	if (i2400m->state == I2400M_SS_DATA_PATH_CONNECTED && is_autosuspend) {
@@ -575,6 +657,7 @@ int i2400mu_resume(struct usb_interface *iface)
 	struct i2400m *i2400m = &i2400mu->i2400m;
 
 	d_fnstart(3, dev, "(iface %p)\n", iface);
+	rmb();		/* see i2400m->updown's documentation  */
 	if (i2400m->updown == 0) {
 		d_printf(1, dev, "fw was down, no resume neeed\n");
 		goto out;
@@ -590,8 +673,55 @@ int i2400mu_resume(struct usb_interface *iface)
 }
 
 
+static
+int i2400mu_reset_resume(struct usb_interface *iface)
+{
+	int result;
+	struct device *dev = &iface->dev;
+	struct i2400mu *i2400mu = usb_get_intfdata(iface);
+	struct i2400m *i2400m = &i2400mu->i2400m;
+
+	d_fnstart(3, dev, "(iface %p)\n", iface);
+	result = i2400m_dev_reset_handle(i2400m, "device reset on resume");
+	d_fnend(3, dev, "(iface %p) = %d\n", iface, result);
+	return result < 0 ? result : 0;
+}
+
+
+/*
+ * Another driver or user space is triggering a reset on the device
+ * which contains the interface passed as an argument. Cease IO and
+ * save any device state you need to restore.
+ *
+ * If you need to allocate memory here, use GFP_NOIO or GFP_ATOMIC, if
+ * you are in atomic context.
+ */
+static
+int i2400mu_pre_reset(struct usb_interface *iface)
+{
+	struct i2400mu *i2400mu = usb_get_intfdata(iface);
+	return i2400m_pre_reset(&i2400mu->i2400m);
+}
+
+
+/*
+ * The reset has completed.  Restore any saved device state and begin
+ * using the device again.
+ *
+ * If you need to allocate memory here, use GFP_NOIO or GFP_ATOMIC, if
+ * you are in atomic context.
+ */
+static
+int i2400mu_post_reset(struct usb_interface *iface)
+{
+	struct i2400mu *i2400mu = usb_get_intfdata(iface);
+	return i2400m_post_reset(&i2400mu->i2400m);
+}
+
+
 static
 struct usb_device_id i2400mu_id_table[] = {
+	{ USB_DEVICE(0x8086, USB_DEVICE_ID_I6050) },
 	{ USB_DEVICE(0x8086, 0x0181) },
 	{ USB_DEVICE(0x8086, 0x1403) },
 	{ USB_DEVICE(0x8086, 0x1405) },
@@ -609,8 +739,11 @@ struct usb_driver i2400mu_driver = {
 	.name = KBUILD_MODNAME,
 	.suspend = i2400mu_suspend,
 	.resume = i2400mu_resume,
+	.reset_resume = i2400mu_reset_resume,
 	.probe = i2400mu_probe,
 	.disconnect = i2400mu_disconnect,
+	.pre_reset = i2400mu_pre_reset,
+	.post_reset = i2400mu_post_reset,
 	.id_table = i2400mu_id_table,
 	.supports_autosuspend = 1,
 };
@@ -618,6 +751,8 @@ struct usb_driver i2400mu_driver = {
 static
 int __init i2400mu_driver_init(void)
 {
+	d_parse_params(D_LEVEL, D_LEVEL_SIZE, i2400mu_debug_params,
+		       "i2400m_usb.debug");
 	return usb_register(&i2400mu_driver);
 }
 module_init(i2400mu_driver_init);
@@ -632,7 +767,7 @@ void __exit i2400mu_driver_exit(void)
 module_exit(i2400mu_driver_exit);
 
 MODULE_AUTHOR("Intel Corporation <linux-wimax@intel.com>");
-MODULE_DESCRIPTION("Intel 2400M WiMAX networking for USB");
+MODULE_DESCRIPTION("Driver for USB based Intel Wireless WiMAX Connection 2400M "
+		   "(5x50 & 6050)");
 MODULE_LICENSE("GPL");
 MODULE_FIRMWARE(I2400MU_FW_FILE_NAME_v1_4);
-MODULE_FIRMWARE(I2400MU_FW_FILE_NAME_v1_3);

include/linux/mmc/sdio_ids.h

@@ -28,6 +28,7 @@
 #define SDIO_DEVICE_ID_INTEL_IWMC3200TOP	0x1404
 #define SDIO_DEVICE_ID_INTEL_IWMC3200GPS	0x1405
 #define SDIO_DEVICE_ID_INTEL_IWMC3200BT		0x1406
+#define SDIO_DEVICE_ID_INTEL_IWMC3200WIMAX_2G5	0x1407
 
 #define SDIO_VENDOR_ID_MARVELL			0x02df
 #define SDIO_DEVICE_ID_MARVELL_LIBERTAS		0x9103

include/linux/wimax/debug.h

@@ -450,4 +450,76 @@ do {							\
 })
 
 
+static inline
+void d_submodule_set(struct d_level *d_level, size_t d_level_size,
+		     const char *submodule, u8 level, const char *tag)
+{
+	struct d_level *itr, *top;
+	int index = -1;
+
+	for (itr = d_level, top = itr + d_level_size; itr < top; itr++) {
+		index++;
+		if (itr->name == NULL) {
+			printk(KERN_ERR "%s: itr->name NULL?? (%p, #%d)\n",
+			       tag, itr, index);
+			continue;
+		}
+		if (!strcmp(itr->name, submodule)) {
+			itr->level = level;
+			return;
+		}
+	}
+	printk(KERN_ERR "%s: unknown submodule %s\n", tag, submodule);
+}
+
+
+/**
+ * d_parse_params - Parse a string with debug parameters from the
+ * command line
+ *
+ * @d_level: level structure (D_LEVEL)
+ * @d_level_size: number of items in the level structure
+ *     (D_LEVEL_SIZE).
+ * @_params: string with the parameters; this is a space (not tab!)
+ *     separated list of NAME:VALUE, where value is the debug level
+ *     and NAME is the name of the submodule.
+ * @tag: string for error messages (example: MODULE.ARGNAME).
+ */
+static inline
+void d_parse_params(struct d_level *d_level, size_t d_level_size,
+		    const char *_params, const char *tag)
+{
+	char submodule[130], *params, *params_orig, *token, *colon;
+	unsigned level, tokens;
+
+	if (_params == NULL)
+		return;
+	params_orig = kstrdup(_params, GFP_KERNEL);
+	params = params_orig;
+	while (1) {
+		token = strsep(&params, " ");
+		if (token == NULL)
+			break;
+		if (*token == '\0')	/* eat joint spaces */
+			continue;
+		/* kernel's sscanf %s eats until whitespace, so we
+		 * replace : by \n so it doesn't get eaten later by
+		 * strsep */
+		colon = strchr(token, ':');
+		if (colon != NULL)
+			*colon = '\n';
+		tokens = sscanf(token, "%s\n%u", submodule, &level);
+		if (colon != NULL)
+			*colon = ':';	/* set back, for error messages */
+		if (tokens == 2)
+			d_submodule_set(d_level, d_level_size,
+					submodule, level, tag);
+		else
+			printk(KERN_ERR "%s: can't parse '%s' as a "
+			       "SUBMODULE:LEVEL (%d tokens)\n",
+			       tag, token, tokens);
+	}
+	kfree(params_orig);
+}
+
 #endif /* #ifndef __debug__h__ */

include/linux/wimax/i2400m.h

@@ -138,7 +138,7 @@ struct i2400m_bcf_hdr {
 	__le32 module_id;
 	__le32 module_vendor;
 	__le32 date;		/* BCD YYYMMDD */
-	__le32 size;
+	__le32 size;            /* in dwords */
 	__le32 key_size;	/* in dwords */
 	__le32 modulus_size;	/* in dwords */
 	__le32 exponent_size;	/* in dwords */
@@ -168,16 +168,6 @@ enum i2400m_brh {
 };
 
 
-/* Constants for bcf->module_id */
-enum i2400m_bcf_mod_id {
-	/* Firmware file carries its own pokes -- pokes are a set of
-	 * magical values that have to be written in certain memory
-	 * addresses to get the device up and ready for firmware
-	 * download when it is in non-signed boot mode. */
-	I2400M_BCF_MOD_ID_POKES = 0x000000001,
-};
-
-
 /**
  * i2400m_bootrom_header - Header for a boot-mode command
  *
@@ -276,6 +266,7 @@ enum {
 	I2400M_WARM_RESET_BARKER = 0x50f750f7,
 	I2400M_NBOOT_BARKER = 0xdeadbeef,
 	I2400M_SBOOT_BARKER = 0x0ff1c1a1,
+	I2400M_SBOOT_BARKER_6050 = 0x80000001,
 	I2400M_ACK_BARKER = 0xfeedbabe,
 	I2400M_D2H_MSG_BARKER = 0xbeefbabe,
 };

include/net/wimax.h

@@ -195,6 +195,12 @@
  *    defining the `struct nla_policy` for each message, it has to have
  *    an array size of WIMAX_GNL_ATTR_MAX+1.
  *
+ * The op_*() function pointers will not be called if the wimax_dev is
+ * in a state <= %WIMAX_ST_UNINITIALIZED. The exception is:
+ *
+ * - op_reset: can be called at any time after wimax_dev_add() has
+ *   been called.
+ *
  * THE PIPE INTERFACE:
  *
  * This interface is kept intentionally simple. The driver can send

net/wimax/op-msg.c

@@ -388,6 +388,8 @@ int wimax_gnl_doit_msg_from_user(struct sk_buff *skb, struct genl_info *info)
 	}
 	mutex_lock(&wimax_dev->mutex);
 	result = wimax_dev_is_ready(wimax_dev);
+	if (result == -ENOMEDIUM)
+		result = 0;
 	if (result < 0)
 		goto error_not_ready;
 	result = -ENOSYS;

net/wimax/op-rfkill.c

@@ -305,8 +305,15 @@ int wimax_rfkill(struct wimax_dev *wimax_dev, enum wimax_rf_state state)
 	d_fnstart(3, dev, "(wimax_dev %p state %u)\n", wimax_dev, state);
 	mutex_lock(&wimax_dev->mutex);
 	result = wimax_dev_is_ready(wimax_dev);
-	if (result < 0)
+	if (result < 0) {
+		/* While initializing, < 1.4.3 wimax-tools versions use
+		 * this call to check if the device is a valid WiMAX
+		 * device; so we allow it to proceed always,
+		 * considering the radios are all off. */
+		if (result == -ENOMEDIUM && state == WIMAX_RF_QUERY)
+			result = WIMAX_RF_OFF << 1 | WIMAX_RF_OFF;
 		goto error_not_ready;
+	}
 	switch (state) {
 	case WIMAX_RF_ON:
 	case WIMAX_RF_OFF:
@@ -355,6 +362,7 @@ int wimax_rfkill_add(struct wimax_dev *wimax_dev)
 
 	wimax_dev->rfkill = rfkill;
 
+	rfkill_init_sw_state(rfkill, 1);
 	result = rfkill_register(wimax_dev->rfkill);
 	if (result < 0)
 		goto error_rfkill_register;

net/wimax/stack.c

@@ -60,6 +60,14 @@
 #define D_SUBMODULE stack
 #include "debug-levels.h"
 
+static char wimax_debug_params[128];
+module_param_string(debug, wimax_debug_params, sizeof(wimax_debug_params),
+		    0644);
+MODULE_PARM_DESC(debug,
+		 "String of space-separated NAME:VALUE pairs, where NAMEs "
+		 "are the different debug submodules and VALUE are the "
+		 "initial debug value to set.");
+
 /*
  * Authoritative source for the RE_STATE_CHANGE attribute policy
  *
@@ -562,6 +570,9 @@ int __init wimax_subsys_init(void)
 	int result, cnt;
 
 	d_fnstart(4, NULL, "()\n");
+	d_parse_params(D_LEVEL, D_LEVEL_SIZE, wimax_debug_params,
+		       "wimax.debug");
+
 	snprintf(wimax_gnl_family.name, sizeof(wimax_gnl_family.name),
 		 "WiMAX");
 	result = genl_register_family(&wimax_gnl_family);