Commit 68701780 authored by Sam Bobroff's avatar Sam Bobroff Committed by Michael Ellerman

powerpc/eeh: Remove eeh_handle_event()

The function eeh_handle_event(pe) does nothing other than switching
between calling eeh_handle_normal_event(pe) and
eeh_handle_special_event(). However it is only called in two places,
one where pe can't be NULL and the other where it must be NULL (see
eeh_event_handler()) so it does nothing but obscure the flow of
control.

So, remove it.
Signed-off-by: default avatarSam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: default avatarAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: default avatarMichael Ellerman <mpe@ellerman.id.au>
parent d41ce7b1
...@@ -34,7 +34,8 @@ struct eeh_event { ...@@ -34,7 +34,8 @@ struct eeh_event {
int eeh_event_init(void); int eeh_event_init(void);
int eeh_send_failure_event(struct eeh_pe *pe); int eeh_send_failure_event(struct eeh_pe *pe);
void eeh_remove_event(struct eeh_pe *pe, bool force); void eeh_remove_event(struct eeh_pe *pe, bool force);
void eeh_handle_event(struct eeh_pe *pe); bool eeh_handle_normal_event(struct eeh_pe *pe);
void eeh_handle_special_event(void);
#endif /* __KERNEL__ */ #endif /* __KERNEL__ */
#endif /* ASM_POWERPC_EEH_EVENT_H */ #endif /* ASM_POWERPC_EEH_EVENT_H */
...@@ -738,9 +738,22 @@ static int eeh_reset_device(struct eeh_pe *pe, struct pci_bus *bus, ...@@ -738,9 +738,22 @@ static int eeh_reset_device(struct eeh_pe *pe, struct pci_bus *bus,
* Attempts to recover the given PE. If recovery fails or the PE has failed * Attempts to recover the given PE. If recovery fails or the PE has failed
* too many times, remove the PE. * too many times, remove the PE.
* *
* While PHB detects address or data parity errors on particular PCI
* slot, the associated PE will be frozen. Besides, DMA's occurring
* to wild addresses (which usually happen due to bugs in device
* drivers or in PCI adapter firmware) can cause EEH error. #SERR,
* #PERR or other misc PCI-related errors also can trigger EEH errors.
*
* Recovery process consists of unplugging the device driver (which
* generated hotplug events to userspace), then issuing a PCI #RST to
* the device, then reconfiguring the PCI config space for all bridges
* & devices under this slot, and then finally restarting the device
* drivers (which cause a second set of hotplug events to go out to
* userspace).
*
* Returns true if @pe should no longer be used, else false. * Returns true if @pe should no longer be used, else false.
*/ */
static bool eeh_handle_normal_event(struct eeh_pe *pe) bool eeh_handle_normal_event(struct eeh_pe *pe)
{ {
struct pci_bus *frozen_bus; struct pci_bus *frozen_bus;
struct eeh_dev *edev, *tmp; struct eeh_dev *edev, *tmp;
...@@ -942,7 +955,7 @@ static bool eeh_handle_normal_event(struct eeh_pe *pe) ...@@ -942,7 +955,7 @@ static bool eeh_handle_normal_event(struct eeh_pe *pe)
* specific PE. Iterates through possible failures and handles them as * specific PE. Iterates through possible failures and handles them as
* necessary. * necessary.
*/ */
static void eeh_handle_special_event(void) void eeh_handle_special_event(void)
{ {
struct eeh_pe *pe, *phb_pe; struct eeh_pe *pe, *phb_pe;
struct pci_bus *bus; struct pci_bus *bus;
...@@ -1049,28 +1062,3 @@ static void eeh_handle_special_event(void) ...@@ -1049,28 +1062,3 @@ static void eeh_handle_special_event(void)
break; break;
} while (rc != EEH_NEXT_ERR_NONE); } while (rc != EEH_NEXT_ERR_NONE);
} }
/**
* eeh_handle_event - Reset a PCI device after hard lockup.
* @pe: EEH PE
*
* While PHB detects address or data parity errors on particular PCI
* slot, the associated PE will be frozen. Besides, DMA's occurring
* to wild addresses (which usually happen due to bugs in device
* drivers or in PCI adapter firmware) can cause EEH error. #SERR,
* #PERR or other misc PCI-related errors also can trigger EEH errors.
*
* Recovery process consists of unplugging the device driver (which
* generated hotplug events to userspace), then issuing a PCI #RST to
* the device, then reconfiguring the PCI config space for all bridges
* & devices under this slot, and then finally restarting the device
* drivers (which cause a second set of hotplug events to go out to
* userspace).
*/
void eeh_handle_event(struct eeh_pe *pe)
{
if (pe)
eeh_handle_normal_event(pe);
else
eeh_handle_special_event();
}
...@@ -81,10 +81,10 @@ static int eeh_event_handler(void * dummy) ...@@ -81,10 +81,10 @@ static int eeh_event_handler(void * dummy)
pr_info("EEH: Detected PCI bus error on " pr_info("EEH: Detected PCI bus error on "
"PHB#%x-PE#%x\n", "PHB#%x-PE#%x\n",
pe->phb->global_number, pe->addr); pe->phb->global_number, pe->addr);
eeh_handle_event(pe); eeh_handle_normal_event(pe);
eeh_pe_state_clear(pe, EEH_PE_RECOVERING); eeh_pe_state_clear(pe, EEH_PE_RECOVERING);
} else { } else {
eeh_handle_event(NULL); eeh_handle_special_event();
} }
kfree(event); kfree(event);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment