Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (43 commits)
  Blackfin: spi-docs: further clarify GPIO CS behavior with various modes
  Blackfin: boards: fix pcm device name
  Blackfin: SMP: punt unused atomic_test_mask helper
  Blackfin: irqs: do not trace arch_local_{*,irq_*} functions
  Blackfin: bf526: restrict reboot workaround to 0.0 silicon
  Blackfin: bf51x: fix alternative portmux options
  Blackfin: bf54x: fix GPIO resume code
  Blackfin: dpmc: optimize SDRAM programming slightly
  Blackfin: dpmc: don't save/restore scratch registers
  Blackfin: bf538: pull gpio/port logic out of core hibernate paths
  Blackfin: dpmc: optimize hibernate/resume path
  Blackfin: dpmc: do not save/restore EVT0/EVT1/EVT4 when hibernating
  Blackfin: dpmc: relocate hibernate helper macros
  Blackfin: dpmc: omit RETE/RETN when hibernating
  Blackfin: dpmc: optimize SIC_IWR programming a little
  Blackfin: gpio/ints: generalize pint logic
  Blackfin: dpmc: bind to MMR names and not CPUs
  Blackfin: debug-mmrs: generalize pint logic
  Blackfin: bf54x: switch to common pint MMR struct
  Blackfin: bf54x: tweak MMR pint names
  ...

Documentation/blackfin/bfin-spi-notes.txt

@@ -9,6 +9,8 @@ the entire SPI transfer. - And not just bits_per_word duration.
 In most cases you can utilize SPI MODE_3 instead of MODE_0 to work-around this
 behavior. If your SPI slave device in question requires SPI MODE_0 or MODE_2
 timing, you can utilize the GPIO controlled SPI Slave Select option instead.
+In this case, you should use GPIO based CS for all of your slaves and not just
+the ones using mode 0 or 2 in order to guarantee correct CS toggling behavior.
 
 You can even use the same pin whose peripheral role is a SSEL,
 but use it as a GPIO instead.

arch/blackfin/Kconfig

@@ -953,6 +953,16 @@ config BFIN_GPTIMERS
 	  To compile this driver as a module, choose M here: the module
 	  will be called gptimers.
 
+config HAVE_PWM
+	tristate "Enable PWM API support"
+	depends on BFIN_GPTIMERS
+	help
+	  Enable support for the Pulse Width Modulation framework (as
+	  found in linux/pwm.h).
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called pwm.
+
 choice
 	prompt "Uncached DMA region"
 	default DMA_UNCACHED_1M

arch/blackfin/configs/BF561-EZKIT_defconfig

@@ -58,13 +58,13 @@ CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_MTD=y
 CONFIG_MTD_PARTITIONS=y
 CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=m
+CONFIG_MTD_CHAR=y
 CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=m
-CONFIG_MTD_CFI_AMDSTD=m
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_AMDSTD=y
 CONFIG_MTD_RAM=y
 CONFIG_MTD_ROM=m
-CONFIG_MTD_PHYSMAP=m
+CONFIG_MTD_PHYSMAP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_NETDEVICES=y
 CONFIG_NET_ETHERNET=y

arch/blackfin/include/asm/Kbuild

 include include/asm-generic/Kbuild.asm
 
+generic-y += auxvec.h
+generic-y += bitsperlong.h
+generic-y += bugs.h
+generic-y += cputime.h
+generic-y += current.h
+generic-y += device.h
+generic-y += div64.h
+generic-y += emergency-restart.h
+generic-y += errno.h
+generic-y += fb.h
+generic-y += futex.h
+generic-y += hw_irq.h
+generic-y += ioctl.h
+generic-y += ipcbuf.h
+generic-y += irq_regs.h
+generic-y += kdebug.h
+generic-y += kmap_types.h
+generic-y += local64.h
+generic-y += local.h
+generic-y += mman.h
+generic-y += msgbuf.h
+generic-y += param.h
+generic-y += percpu.h
+generic-y += pgalloc.h
+generic-y += resource.h
+generic-y += scatterlist.h
+generic-y += sembuf.h
+generic-y += serial.h
+generic-y += setup.h
+generic-y += shmbuf.h
+generic-y += shmparam.h
+generic-y += socket.h
+generic-y += sockios.h
+generic-y += statfs.h
+generic-y += termbits.h
+generic-y += termios.h
+generic-y += topology.h
+generic-y += types.h
+generic-y += ucontext.h
+generic-y += unaligned.h
+generic-y += user.h
+generic-y += xor.h
+
 header-y += bfin_sport.h
 header-y += cachectl.h
 header-y += fixed_code.h

arch/blackfin/include/asm/atomic.h

 /*
- * Copyright 2004-2009 Analog Devices Inc.
- *
- * Licensed under the GPL-2 or later.
- */
+ * Copyright 2004-2009 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
 
 #ifndef __ARCH_BLACKFIN_ATOMIC__
 #define __ARCH_BLACKFIN_ATOMIC__
@@ -76,11 +76,6 @@ static inline void atomic_set_mask(int mask, atomic_t *v)
 	__raw_atomic_set_asm(&v->counter, mask);
 }
 
-static inline int atomic_test_mask(int mask, atomic_t *v)
-{
-	return __raw_atomic_test_asm(&v->counter, mask);
-}
-
 /* Atomic operations are already serializing */
 #define smp_mb__before_atomic_dec()    barrier()
 #define smp_mb__after_atomic_dec() barrier()

arch/blackfin/include/asm/auxvec.h

-#include <asm-generic/auxvec.h>

arch/blackfin/include/asm/bitsperlong.h

-#include <asm-generic/bitsperlong.h>

arch/blackfin/include/asm/blackfin.h

 /*
  * Common header file for Blackfin family of processors.
  *
- * Copyright 2004-2009 Analog Devices Inc.
- *
- * Licensed under the GPL-2 or later.
+ * Copyright 2004-2009 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
  */
 
 #ifndef _BLACKFIN_H_

arch/blackfin/include/asm/bugs.h

-#include <asm-generic/bugs.h>

arch/blackfin/include/asm/cputime.h

-#include <asm-generic/cputime.h>

arch/blackfin/include/asm/current.h

-#include <asm-generic/current.h>

arch/blackfin/include/asm/device.h

-#include <asm-generic/device.h>

arch/blackfin/include/asm/div64.h

-#include <asm-generic/div64.h>

arch/blackfin/include/asm/dpmc.h

@@ -117,7 +117,6 @@
 #ifndef __ASSEMBLY__
 
 void sleep_mode(u32 sic_iwr0, u32 sic_iwr1, u32 sic_iwr2);
-void hibernate_mode(u32 sic_iwr0, u32 sic_iwr1, u32 sic_iwr2);
 void sleep_deeper(u32 sic_iwr0, u32 sic_iwr1, u32 sic_iwr2);
 void do_hibernate(int wakeup);
 void set_dram_srfs(void);
@@ -134,32 +133,6 @@ struct bfin_dpmc_platform_data {
 	unsigned short vr_settling_time; /* in us */
 };
 
-#else
-
-#define PM_PUSH(x) \
-	R0 = [P0 + (x - SRAM_BASE_ADDRESS)];\
-	[--SP] =  R0;\
-
-#define PM_POP(x) \
-	R0 = [SP++];\
-	[P0 + (x - SRAM_BASE_ADDRESS)] = R0;\
-
-#define PM_SYS_PUSH(x) \
-	R0 = [P0 + (x - PLL_CTL)];\
-	[--SP] =  R0;\
-
-#define PM_SYS_POP(x) \
-	R0 = [SP++];\
-	[P0 + (x - PLL_CTL)] = R0;\
-
-#define PM_SYS_PUSH16(x) \
-	R0 = w[P0 + (x - PLL_CTL)];\
-	[--SP] =  R0;\
-
-#define PM_SYS_POP16(x) \
-	R0 = [SP++];\
-	w[P0 + (x - PLL_CTL)] = R0;\
-
 #endif
 
 #endif	/*_BLACKFIN_DPMC_H_*/

arch/blackfin/include/asm/emergency-restart.h

-#include <asm-generic/emergency-restart.h>

arch/blackfin/include/asm/errno.h

-#include <asm-generic/errno.h>

arch/blackfin/include/asm/fb.h

-#include <asm-generic/fb.h>

arch/blackfin/include/asm/futex.h

-#include <asm-generic/futex.h>

arch/blackfin/include/asm/gpio.h

@@ -16,58 +16,13 @@
 
 #include <mach/gpio.h>
 
-#define GPIO_0	0
-#define GPIO_1	1
-#define GPIO_2	2
-#define GPIO_3	3
-#define GPIO_4	4
-#define GPIO_5	5
-#define GPIO_6	6
-#define GPIO_7	7
-#define GPIO_8	8
-#define GPIO_9	9
-#define GPIO_10	10
-#define GPIO_11	11
-#define GPIO_12	12
-#define GPIO_13	13
-#define GPIO_14	14
-#define GPIO_15	15
-#define GPIO_16	16
-#define GPIO_17	17
-#define GPIO_18	18
-#define GPIO_19	19
-#define GPIO_20	20
-#define GPIO_21	21
-#define GPIO_22	22
-#define GPIO_23	23
-#define GPIO_24	24
-#define GPIO_25	25
-#define GPIO_26	26
-#define GPIO_27	27
-#define GPIO_28	28
-#define GPIO_29	29
-#define GPIO_30	30
-#define GPIO_31	31
-#define GPIO_32	32
-#define GPIO_33	33
-#define GPIO_34	34
-#define GPIO_35	35
-#define GPIO_36	36
-#define GPIO_37	37
-#define GPIO_38	38
-#define GPIO_39	39
-#define GPIO_40	40
-#define GPIO_41	41
-#define GPIO_42	42
-#define GPIO_43	43
-#define GPIO_44	44
-#define GPIO_45	45
-#define GPIO_46	46
-#define GPIO_47	47
-
 #define PERIPHERAL_USAGE 1
 #define GPIO_USAGE 0
 
+#ifndef BFIN_GPIO_PINT
+# define BFIN_GPIO_PINT 0
+#endif
+
 #ifndef __ASSEMBLY__
 
 #include <linux/compiler.h>
@@ -89,7 +44,7 @@
 * MODIFICATION HISTORY :
 **************************************************************/
 
-#ifndef CONFIG_BF54x
+#if !BFIN_GPIO_PINT
 void set_gpio_dir(unsigned, unsigned short);
 void set_gpio_inen(unsigned, unsigned short);
 void set_gpio_polar(unsigned, unsigned short);
@@ -164,6 +119,10 @@ struct gpio_port_t {
 #ifdef BFIN_SPECIAL_GPIO_BANKS
 void bfin_special_gpio_free(unsigned gpio);
 int bfin_special_gpio_request(unsigned gpio, const char *label);
+# ifdef CONFIG_PM
+void bfin_special_gpio_pm_hibernate_restore(void);
+void bfin_special_gpio_pm_hibernate_suspend(void);
+# endif
 #endif
 
 #ifdef CONFIG_PM
@@ -182,7 +141,7 @@ static inline void bfin_pm_standby_restore(void)
 void bfin_gpio_pm_hibernate_restore(void);
 void bfin_gpio_pm_hibernate_suspend(void);
 
-#ifndef CONFIG_BF54x
+# if !BFIN_GPIO_PINT
 int gpio_pm_wakeup_ctrl(unsigned gpio, unsigned ctrl);
 
 struct gpio_port_s {
@@ -199,8 +158,9 @@ struct gpio_port_s {
 	unsigned short reserved;
 	unsigned short mux;
 };
-#endif /*CONFIG_BF54x*/
+# endif
 #endif /*CONFIG_PM*/
+
 /***********************************************************
 *
 * FUNCTIONS: Blackfin GPIO Driver

arch/blackfin/include/asm/gptimers.h

@@ -193,6 +193,16 @@ uint16_t get_enabled_gptimers(void);
 uint32_t get_gptimer_status(unsigned int group);
 void     set_gptimer_status(unsigned int group, uint32_t value);
 
+static inline void enable_gptimer(unsigned int timer_id)
+{
+	enable_gptimers(1 << timer_id);
+}
+
+static inline void disable_gptimer(unsigned int timer_id)
+{
+	disable_gptimers(1 << timer_id);
+}
+
 /*
  * All Blackfin system MMRs are padded to 32bits even if the register
  * itself is only 16bits.  So use a helper macro to streamline this.
@@ -209,6 +219,15 @@ struct bfin_gptimer_regs {
 	u32 width;
 };
 
+/*
+ * bfin group timer registers layout
+ */
+struct bfin_gptimer_group_regs {
+	__BFP(enable);
+	__BFP(disable);
+	u32 status;
+};
+
 #undef __BFP
 
 #endif

arch/blackfin/include/asm/hw_irq.h

-#include <asm-generic/hw_irq.h>

arch/blackfin/include/asm/ioctl.h

-#include <asm-generic/ioctl.h>

arch/blackfin/include/asm/ipcbuf.h

-#include <asm-generic/ipcbuf.h>

arch/blackfin/include/asm/irq_regs.h

-#include <asm-generic/irq_regs.h>

arch/blackfin/include/asm/irqflags.h

@@ -18,12 +18,12 @@
 extern unsigned long bfin_irq_flags;
 #endif
 
-static inline void bfin_sti(unsigned long flags)
+static inline notrace void bfin_sti(unsigned long flags)
 {
 	asm volatile("sti %0;" : : "d" (flags));
 }
 
-static inline unsigned long bfin_cli(void)
+static inline notrace unsigned long bfin_cli(void)
 {
 	unsigned long flags;
 	asm volatile("cli %0;" : "=d" (flags));
@@ -40,22 +40,22 @@ static inline unsigned long bfin_cli(void)
 /*
  * Hard, untraced CPU interrupt flag manipulation and access.
  */
-static inline void __hard_local_irq_disable(void)
+static inline notrace void __hard_local_irq_disable(void)
 {
 	bfin_cli();
 }
 
-static inline void __hard_local_irq_enable(void)
+static inline notrace void __hard_local_irq_enable(void)
 {
 	bfin_sti(bfin_irq_flags);
 }
 
-static inline unsigned long hard_local_save_flags(void)
+static inline notrace unsigned long hard_local_save_flags(void)
 {
 	return bfin_read_IMASK();
 }
 
-static inline unsigned long __hard_local_irq_save(void)
+static inline notrace unsigned long __hard_local_irq_save(void)
 {
 	unsigned long flags;
 	flags = bfin_cli();
@@ -65,18 +65,18 @@ static inline unsigned long __hard_local_irq_save(void)
 	return flags;
 }
 
-static inline int hard_irqs_disabled_flags(unsigned long flags)
+static inline notrace int hard_irqs_disabled_flags(unsigned long flags)
 {
 	return (flags & ~0x3f) == 0;
 }
 
-static inline int hard_irqs_disabled(void)
+static inline notrace int hard_irqs_disabled(void)
 {
 	unsigned long flags = hard_local_save_flags();
 	return hard_irqs_disabled_flags(flags);
 }
 
-static inline void __hard_local_irq_restore(unsigned long flags)
+static inline notrace void __hard_local_irq_restore(unsigned long flags)
 {
 	if (!hard_irqs_disabled_flags(flags))
 		__hard_local_irq_enable();
@@ -113,31 +113,31 @@ void ipipe_check_context(struct ipipe_domain *ipd);
 /*
  * Interrupt pipe interface to linux/irqflags.h.
  */
-static inline void arch_local_irq_disable(void)
+static inline notrace void arch_local_irq_disable(void)
 {
 	__check_irqop_context();
 	__ipipe_stall_root();
 	barrier();
 }
 
-static inline void arch_local_irq_enable(void)
+static inline notrace void arch_local_irq_enable(void)
 {
 	barrier();
 	__check_irqop_context();
 	__ipipe_unstall_root();
 }
 
-static inline unsigned long arch_local_save_flags(void)
+static inline notrace unsigned long arch_local_save_flags(void)
 {
 	return __ipipe_test_root() ? bfin_no_irqs : bfin_irq_flags;
 }
 
-static inline int arch_irqs_disabled_flags(unsigned long flags)
+static inline notrace int arch_irqs_disabled_flags(unsigned long flags)
 {
 	return flags == bfin_no_irqs;
 }
 
-static inline unsigned long arch_local_irq_save(void)
+static inline notrace unsigned long arch_local_irq_save(void)
 {
 	unsigned long flags;
 
@@ -148,13 +148,13 @@ static inline unsigned long arch_local_irq_save(void)
 	return flags;
 }
 
-static inline void arch_local_irq_restore(unsigned long flags)
+static inline notrace void arch_local_irq_restore(unsigned long flags)
 {
 	__check_irqop_context();
 	__ipipe_restore_root(flags == bfin_no_irqs);
 }
 
-static inline unsigned long arch_mangle_irq_bits(int virt, unsigned long real)
+static inline notrace unsigned long arch_mangle_irq_bits(int virt, unsigned long real)
 {
 	/*
 	 * Merge virtual and real interrupt mask bits into a single
@@ -163,7 +163,7 @@ static inline unsigned long arch_mangle_irq_bits(int virt, unsigned long real)
 	return (real & ~(1 << 31)) | ((virt != 0) << 31);
 }
 
-static inline int arch_demangle_irq_bits(unsigned long *x)
+static inline notrace int arch_demangle_irq_bits(unsigned long *x)
 {
 	int virt = (*x & (1 << 31)) != 0;
 	*x &= ~(1L << 31);
@@ -174,7 +174,7 @@ static inline int arch_demangle_irq_bits(unsigned long *x)
  * Interface to various arch routines that may be traced.
  */
 #ifdef CONFIG_IPIPE_TRACE_IRQSOFF
-static inline void hard_local_irq_disable(void)
+static inline notrace void hard_local_irq_disable(void)
 {
 	if (!hard_irqs_disabled()) {
 		__hard_local_irq_disable();
@@ -182,7 +182,7 @@ static inline void hard_local_irq_disable(void)
 	}
 }
 
-static inline void hard_local_irq_enable(void)
+static inline notrace void hard_local_irq_enable(void)
 {
 	if (hard_irqs_disabled()) {
 		ipipe_trace_end(0x80000000);
@@ -190,7 +190,7 @@ static inline void hard_local_irq_enable(void)
 	}
 }
 
-static inline unsigned long hard_local_irq_save(void)
+static inline notrace unsigned long hard_local_irq_save(void)
 {
 	unsigned long flags = hard_local_save_flags();
 	if (!hard_irqs_disabled_flags(flags)) {
@@ -200,7 +200,7 @@ static inline unsigned long hard_local_irq_save(void)
 	return flags;
 }
 
-static inline void hard_local_irq_restore(unsigned long flags)
+static inline notrace void hard_local_irq_restore(unsigned long flags)
 {
 	if (!hard_irqs_disabled_flags(flags)) {
 		ipipe_trace_end(0x80000001);

arch/blackfin/include/asm/kdebug.h

-#include <asm-generic/kdebug.h>

arch/blackfin/include/asm/kmap_types.h

-#include <asm-generic/kmap_types.h>

arch/blackfin/include/asm/local.h

-#include <asm-generic/local.h>

arch/blackfin/include/asm/local64.h

-#include <asm-generic/local64.h>

arch/blackfin/include/asm/mman.h

-#include <asm-generic/mman.h>

arch/blackfin/include/asm/module.h

 /*
- * Copyright 2004-2008 Analog Devices Inc.
- *
- * Licensed under the GPL-2 or later.
- */
+ * Copyright 2004-2008 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
 
 #ifndef _ASM_BFIN_MODULE_H
 #define _ASM_BFIN_MODULE_H

arch/blackfin/include/asm/msgbuf.h

-#include <asm-generic/msgbuf.h>

arch/blackfin/include/asm/mutex.h

-/*
- * Pull in the generic implementation for the mutex fastpath.
- *
- * TODO: implement optimized primitives instead, or leave the generic
- * implementation in place, or pick the atomic_xchg() based generic
- * implementation. (see asm-generic/mutex-xchg.h for details)
- *
- * Copyright 2006-2009 Analog Devices Inc.
- *
- * Licensed under the GPL-2 or later.
- */
-
-#ifndef _ASM_MUTEX_H
-#define _ASM_MUTEX_H
-
-#ifndef CONFIG_SMP
-#include <asm-generic/mutex.h>
-#else
-
-static inline void
-__mutex_fastpath_lock(atomic_t *count, void (*fail_fn)(atomic_t *))
-{
-	if (unlikely(atomic_dec_return(count) < 0))
-		fail_fn(count);
-	else
-		smp_mb();
-}
-
-static inline int
-__mutex_fastpath_lock_retval(atomic_t *count, int (*fail_fn)(atomic_t *))
-{
-	if (unlikely(atomic_dec_return(count) < 0))
-		return fail_fn(count);
-	else {
-		smp_mb();
-		return 0;
-	}
-}
-
-static inline void
-__mutex_fastpath_unlock(atomic_t *count, void (*fail_fn)(atomic_t *))
-{
-	smp_mb();
-	if (unlikely(atomic_inc_return(count) <= 0))
-		fail_fn(count);
-}
-
-#define __mutex_slowpath_needs_to_unlock()		1
-
-static inline int
-__mutex_fastpath_trylock(atomic_t *count, int (*fail_fn)(atomic_t *))
-{
-	/*
-	 * We have two variants here. The cmpxchg based one is the best one
-	 * because it never induce a false contention state.  It is included
-	 * here because architectures using the inc/dec algorithms over the
-	 * xchg ones are much more likely to support cmpxchg natively.
-	 *
-	 * If not we fall back to the spinlock based variant - that is
-	 * just as efficient (and simpler) as a 'destructive' probing of
-	 * the mutex state would be.
-	 */
-#ifdef __HAVE_ARCH_CMPXCHG
-	if (likely(atomic_cmpxchg(count, 1, 0) == 1)) {
-		smp_mb();
-		return 1;
-	}
-	return 0;
-#else
-	return fail_fn(count);
-#endif
-}
-
-#endif
-
-#endif
+#include <asm-generic/mutex-dec.h>

arch/blackfin/include/asm/page.h

 /*
- * Copyright 2004-2009 Analog Devices Inc.
- *
- * Licensed under the GPL-2 or later.
- */
+ * Copyright 2004-2009 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
 
 #ifndef _BLACKFIN_PAGE_H
 #define _BLACKFIN_PAGE_H

arch/blackfin/include/asm/param.h

-#include <asm-generic/param.h>

arch/blackfin/include/asm/pda.h

@@ -54,6 +54,16 @@ struct blackfin_pda {			/* Per-processor Data Area */
 #endif
 };
 
+struct blackfin_initial_pda {
+	void *retx;
+#ifdef CONFIG_DEBUG_DOUBLEFAULT
+	void *dcplb_doublefault_addr;
+	void *icplb_doublefault_addr;
+	void *retx_doublefault;
+	unsigned seqstat_doublefault;
+#endif
+};
+
 extern struct blackfin_pda cpu_pda[];
 
 #endif	/* __ASSEMBLY__ */

arch/blackfin/include/asm/percpu.h

-#include <asm-generic/percpu.h>

arch/blackfin/include/asm/pgalloc.h

-#include <asm-generic/pgalloc.h>

arch/blackfin/include/asm/resource.h

-#include <asm-generic/resource.h>

arch/blackfin/include/asm/scatterlist.h

-#ifndef _BLACKFIN_SCATTERLIST_H
-#define _BLACKFIN_SCATTERLIST_H
-
-#include <asm-generic/scatterlist.h>
-
-#endif				/* !(_BLACKFIN_SCATTERLIST_H) */

arch/blackfin/include/asm/sections.h

 /*
- * Copyright 2004-2009 Analog Devices Inc.
- *
- * Licensed under the GPL-2 or later.
- */
+ * Copyright 2004-2009 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
 
 #ifndef _BLACKFIN_SECTIONS_H
 #define _BLACKFIN_SECTIONS_H

arch/blackfin/include/asm/sembuf.h

-#include <asm-generic/sembuf.h>

arch/blackfin/include/asm/serial.h

-#include <asm-generic/serial.h>

arch/blackfin/include/asm/setup.h

-#include <asm-generic/setup.h>

arch/blackfin/include/asm/shmbuf.h

-#include <asm-generic/shmbuf.h>

arch/blackfin/include/asm/shmparam.h

-#include <asm-generic/shmparam.h>

arch/blackfin/include/asm/sigcontext.h

 /*
- * Copyright 2004-2008 Analog Devices Inc.
- *
- * Licensed under the GPL-2 or later.
- */
+ * Copyright 2004-2008 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
 
 #ifndef _ASM_BLACKFIN_SIGCONTEXT_H
 #define _ASM_BLACKFIN_SIGCONTEXT_H

arch/blackfin/include/asm/socket.h

-#include <asm-generic/socket.h>

arch/blackfin/include/asm/sockios.h

-#include <asm-generic/sockios.h>

arch/blackfin/include/asm/spinlock.h

 /*
- * Copyright 2004-2009 Analog Devices Inc.
- *
- * Licensed under the GPL-2 or later.
- */
+ * Copyright 2004-2009 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
 
 #ifndef __BFIN_SPINLOCK_H
 #define __BFIN_SPINLOCK_H

arch/blackfin/include/asm/statfs.h

-#include <asm-generic/statfs.h>

arch/blackfin/include/asm/termbits.h

-#include <asm-generic/termbits.h>

arch/blackfin/include/asm/termios.h

-#include <asm-generic/termios.h>

arch/blackfin/include/asm/topology.h

-#include <asm-generic/topology.h>

arch/blackfin/include/asm/types.h

-#include <asm-generic/types.h>

arch/blackfin/include/asm/ucontext.h

-#include <asm-generic/ucontext.h>

arch/blackfin/include/asm/unaligned.h

-#include <asm-generic/unaligned.h>

arch/blackfin/include/asm/user.h

-#include <asm-generic/user.h>

arch/blackfin/include/asm/xor.h

-#include <asm-generic/xor.h>

arch/blackfin/kernel/Makefile

@@ -21,6 +21,7 @@ obj-$(CONFIG_FUNCTION_TRACER)        += ftrace-entry.o
 obj-$(CONFIG_FUNCTION_GRAPH_TRACER)  += ftrace.o
 CFLAGS_REMOVE_ftrace.o = -pg
 
+obj-$(CONFIG_HAVE_PWM)               += pwm.o
 obj-$(CONFIG_IPIPE)                  += ipipe.o
 obj-$(CONFIG_BFIN_GPTIMERS)          += gptimers.o
 obj-$(CONFIG_CPLB_INFO)              += cplbinfo.o

arch/blackfin/kernel/asm-offsets.c

@@ -138,6 +138,16 @@ int main(void)
 	DEFINE(PDA_DF_SEQSTAT, offsetof(struct blackfin_pda, seqstat_doublefault));
 	DEFINE(PDA_DF_RETX, offsetof(struct blackfin_pda, retx_doublefault));
 #endif
+
+	/* PDA initial management */
+	DEFINE(PDA_INIT_RETX, offsetof(struct blackfin_initial_pda, retx));
+#ifdef CONFIG_DEBUG_DOUBLEFAULT
+	DEFINE(PDA_INIT_DF_DCPLB, offsetof(struct blackfin_initial_pda, dcplb_doublefault_addr));
+	DEFINE(PDA_INIT_DF_ICPLB, offsetof(struct blackfin_initial_pda, icplb_doublefault_addr));
+	DEFINE(PDA_INIT_DF_SEQSTAT, offsetof(struct blackfin_initial_pda, seqstat_doublefault));
+	DEFINE(PDA_INIT_DF_RETX, offsetof(struct blackfin_initial_pda, retx_doublefault));
+#endif
+
 #ifdef CONFIG_SMP
 	/* Inter-core lock (in L2 SRAM) */
 	DEFINE(SIZEOF_CORELOCK, sizeof(struct corelock_slot));

arch/blackfin/kernel/bfin_gpio.c

@@ -118,6 +118,9 @@ static struct str_ident {
 
 #if defined(CONFIG_PM)
 static struct gpio_port_s gpio_bank_saved[GPIO_BANK_NUM];
+# ifdef BF538_FAMILY
+static unsigned short port_fer_saved[3];
+# endif
 #endif
 
 static void gpio_error(unsigned gpio)
@@ -604,6 +607,11 @@ void bfin_gpio_pm_hibernate_suspend(void)
 {
 	int i, bank;
 
+#ifdef BF538_FAMILY
+	for (i = 0; i < ARRAY_SIZE(port_fer_saved); ++i)
+		port_fer_saved[i] = *port_fer[i];
+#endif
+
 	for (i = 0; i < MAX_BLACKFIN_GPIOS; i += GPIO_BANKSIZE) {
 		bank = gpio_bank(i);
 
@@ -625,6 +633,10 @@ void bfin_gpio_pm_hibernate_suspend(void)
 		gpio_bank_saved[bank].maska = gpio_array[bank]->maska;
 	}
 
+#ifdef BFIN_SPECIAL_GPIO_BANKS
+	bfin_special_gpio_pm_hibernate_suspend();
+#endif
+
 	AWA_DUMMY_READ(maska);
 }
 
@@ -632,6 +644,11 @@ void bfin_gpio_pm_hibernate_restore(void)
 {
 	int i, bank;
 
+#ifdef BF538_FAMILY
+	for (i = 0; i < ARRAY_SIZE(port_fer_saved); ++i)
+		*port_fer[i] = port_fer_saved[i];
+#endif
+
 	for (i = 0; i < MAX_BLACKFIN_GPIOS; i += GPIO_BANKSIZE) {
 		bank = gpio_bank(i);
 
@@ -653,6 +670,11 @@ void bfin_gpio_pm_hibernate_restore(void)
 		gpio_array[bank]->both  = gpio_bank_saved[bank].both;
 		gpio_array[bank]->maska = gpio_bank_saved[bank].maska;
 	}
+
+#ifdef BFIN_SPECIAL_GPIO_BANKS
+	bfin_special_gpio_pm_hibernate_restore();
+#endif
+
 	AWA_DUMMY_READ(maska);
 }
 
@@ -691,9 +713,9 @@ void bfin_gpio_pm_hibernate_restore(void)
 		gpio_array[bank]->port_mux = gpio_bank_saved[bank].mux;
 		gpio_array[bank]->port_fer = gpio_bank_saved[bank].fer;
 		gpio_array[bank]->inen = gpio_bank_saved[bank].inen;
-		gpio_array[bank]->dir_set = gpio_bank_saved[bank].dir;
 		gpio_array[bank]->data_set = gpio_bank_saved[bank].data
-						| gpio_bank_saved[bank].dir;
+						& gpio_bank_saved[bank].dir;
+		gpio_array[bank]->dir_set = gpio_bank_saved[bank].dir;
 	}
 }
 #endif

arch/blackfin/kernel/debug-mmrs.c

@@ -27,7 +27,7 @@
 #define PORT_MUX BFIN_PORT_MUX
 #endif
 
-#define _d(name, bits, addr, perms) debugfs_create_x##bits(name, perms, parent, (u##bits *)addr)
+#define _d(name, bits, addr, perms) debugfs_create_x##bits(name, perms, parent, (u##bits *)(addr))
 #define d(name, bits, addr)         _d(name, bits, addr, S_IRUSR|S_IWUSR)
 #define d_RO(name, bits, addr)      _d(name, bits, addr, S_IRUSR)
 #define d_WO(name, bits, addr)      _d(name, bits, addr, S_IWUSR)
@@ -223,6 +223,7 @@ bfin_debug_mmrs_dma(struct dentry *parent, unsigned long base, int num, char mdm
 	__DMA(CURR_DESC_PTR, curr_desc_ptr);
 	__DMA(CURR_ADDR, curr_addr);
 	__DMA(IRQ_STATUS, irq_status);
+	if (strcmp(pfx, "IMDMA") != 0)
 		__DMA(PERIPHERAL_MAP, peripheral_map);
 	__DMA(CURR_X_COUNT, curr_x_count);
 	__DMA(CURR_Y_COUNT, curr_y_count);
@@ -277,6 +278,32 @@ bfin_debug_mmrs_gptimer(struct dentry *parent, unsigned long base, int num)
 }
 #define GPTIMER(num) bfin_debug_mmrs_gptimer(parent, TIMER##num##_CONFIG, num)
 
+#define GPTIMER_GROUP_OFF(mmr) REGS_OFF(gptimer_group, mmr)
+#define __GPTIMER_GROUP(uname, lname) __REGS(gptimer_group, #uname, lname)
+static void __init __maybe_unused
+bfin_debug_mmrs_gptimer_group(struct dentry *parent, unsigned long base, int num)
+{
+	char buf[32], *_buf;
+
+	if (num == -1) {
+		_buf = buf + sprintf(buf, "TIMER_");
+		__GPTIMER_GROUP(ENABLE, enable);
+		__GPTIMER_GROUP(DISABLE, disable);
+		__GPTIMER_GROUP(STATUS, status);
+	} else {
+		/* These MMRs are a bit odd as the group # is a suffix */
+		_buf = buf + sprintf(buf, "TIMER_ENABLE%i", num);
+		d(buf, 16, base + GPTIMER_GROUP_OFF(enable));
+
+		_buf = buf + sprintf(buf, "TIMER_DISABLE%i", num);
+		d(buf, 16, base + GPTIMER_GROUP_OFF(disable));
+
+		_buf = buf + sprintf(buf, "TIMER_STATUS%i", num);
+		d(buf, 32, base + GPTIMER_GROUP_OFF(status));
+	}
+}
+#define GPTIMER_GROUP(mmr, num) bfin_debug_mmrs_gptimer_group(parent, mmr, num)
+
 /*
  * Handshake MDMA
  */
@@ -295,6 +322,29 @@ bfin_debug_mmrs_hmdma(struct dentry *parent, unsigned long base, int num)
 }
 #define HMDMA(num) bfin_debug_mmrs_hmdma(parent, HMDMA##num##_CONTROL, num)
 
+/*
+ * Peripheral Interrupts (PINT/GPIO)
+ */
+#ifdef PINT0_MASK_SET
+#define __PINT(uname, lname) __REGS(pint, #uname, lname)
+static void __init __maybe_unused
+bfin_debug_mmrs_pint(struct dentry *parent, unsigned long base, int num)
+{
+	char buf[32], *_buf = REGS_STR_PFX(buf, PINT, num);
+	__PINT(MASK_SET, mask_set);
+	__PINT(MASK_CLEAR, mask_clear);
+	__PINT(REQUEST, request);
+	__PINT(ASSIGN, assign);
+	__PINT(EDGE_SET, edge_set);
+	__PINT(EDGE_CLEAR, edge_clear);
+	__PINT(INVERT_SET, invert_set);
+	__PINT(INVERT_CLEAR, invert_clear);
+	__PINT(PINSTATE, pinstate);
+	__PINT(LATCH, latch);
+}
+#define PINT(num) bfin_debug_mmrs_pint(parent, PINT##num##_MASK_SET, num)
+#endif
+
 /*
  * Port/GPIO
  */
@@ -747,7 +797,7 @@ static int __init bfin_debug_mmrs_init(void)
 #endif
 
 	parent = debugfs_create_dir("dmac", top);
-#ifdef DMA_TC_CNT
+#ifdef DMAC_TC_CNT
 	D16(DMAC_TC_CNT);
 	D16(DMAC_TC_PER);
 #endif
@@ -1005,29 +1055,19 @@ static int __init bfin_debug_mmrs_init(void)
 #endif
 
 	parent = debugfs_create_dir("gptimer", top);
-#ifdef TIMER_DISABLE
-	D16(TIMER_DISABLE);
-	D16(TIMER_ENABLE);
-	D32(TIMER_STATUS);
+#ifdef TIMER_ENABLE
+	GPTIMER_GROUP(TIMER_ENABLE, -1);
 #endif
-#ifdef TIMER_DISABLE0
-	D16(TIMER_DISABLE0);
-	D16(TIMER_ENABLE0);
-	D32(TIMER_STATUS0);
+#ifdef TIMER_ENABLE0
+	GPTIMER_GROUP(TIMER_ENABLE0, 0);
 #endif
-#ifdef TIMER_DISABLE1
-	D16(TIMER_DISABLE1);
-	D16(TIMER_ENABLE1);
-	D32(TIMER_STATUS1);
+#ifdef TIMER_ENABLE1
+	GPTIMER_GROUP(TIMER_ENABLE1, 1);
 #endif
 	/* XXX: Should convert BF561 MMR names */
 #ifdef TMRS4_DISABLE
-	D16(TMRS4_DISABLE);
-	D16(TMRS4_ENABLE);
-	D32(TMRS4_STATUS);
-	D16(TMRS8_DISABLE);
-	D16(TMRS8_ENABLE);
-	D32(TMRS8_STATUS);
+	GPTIMER_GROUP(TMRS4_ENABLE, 0);
+	GPTIMER_GROUP(TMRS8_ENABLE, 1);
 #endif
 	GPTIMER(0);
 	GPTIMER(1);
@@ -1253,6 +1293,14 @@ static int __init bfin_debug_mmrs_init(void)
 	D32(OTP_DATA3);
 #endif
 
+#ifdef PINT0_MASK_SET
+	parent = debugfs_create_dir("pint", top);
+	PINT(0);
+	PINT(1);
+	PINT(2);
+	PINT(3);
+#endif
+
 #ifdef PIXC_CTL
 	parent = debugfs_create_dir("pixc", top);
 	D16(PIXC_CTL);
@@ -1816,7 +1864,6 @@ static int __init bfin_debug_mmrs_init(void)
 	{
 		int num;
 		unsigned long base;
-		char *_buf, buf[32];
 
 		base = PORTA_FER;
 		for (num = 0; num < 10; ++num) {
@@ -1824,24 +1871,6 @@ static int __init bfin_debug_mmrs_init(void)
 			base += sizeof(struct bfin_gpio_regs);
 		}
 
-#define __PINT(uname, lname) __REGS(pint, #uname, lname)
-		parent = debugfs_create_dir("pint", top);
-		base = PINT0_MASK_SET;
-		for (num = 0; num < 4; ++num) {
-			_buf = REGS_STR_PFX(buf, PINT, num);
-			__PINT(MASK_SET, mask_set);
-			__PINT(MASK_CLEAR, mask_clear);
-			__PINT(IRQ, irq);
-			__PINT(ASSIGN, assign);
-			__PINT(EDGE_SET, edge_set);
-			__PINT(EDGE_CLEAR, edge_clear);
-			__PINT(INVERT_SET, invert_set);
-			__PINT(INVERT_CLEAR, invert_clear);
-			__PINT(PINSTATE, pinstate);
-			__PINT(LATCH, latch);
-			base += sizeof(struct bfin_pint_regs);
-		}
-
 	}
 #endif	/* BF54x */
 

arch/blackfin/kernel/gptimers.c

@@ -25,49 +25,33 @@
 
 #define BFIN_TIMER_NUM_GROUP  (BFIN_TIMER_OCTET(MAX_BLACKFIN_GPTIMERS - 1) + 1)
 
-typedef struct {
-	uint16_t config;
-	uint16_t __pad;
-	uint32_t counter;
-	uint32_t period;
-	uint32_t width;
-} GPTIMER_timer_regs;
-
-typedef struct {
-	uint16_t enable;
-	uint16_t __pad0;
-	uint16_t disable;
-	uint16_t __pad1;
-	uint32_t status;
-} GPTIMER_group_regs;
-
-static volatile GPTIMER_timer_regs *const timer_regs[MAX_BLACKFIN_GPTIMERS] =
+static struct bfin_gptimer_regs * const timer_regs[MAX_BLACKFIN_GPTIMERS] =
 {
-	(GPTIMER_timer_regs *)TIMER0_CONFIG,
-	(GPTIMER_timer_regs *)TIMER1_CONFIG,
-	(GPTIMER_timer_regs *)TIMER2_CONFIG,
+	(void *)TIMER0_CONFIG,
+	(void *)TIMER1_CONFIG,
+	(void *)TIMER2_CONFIG,
 #if (MAX_BLACKFIN_GPTIMERS > 3)
-	(GPTIMER_timer_regs *)TIMER3_CONFIG,
-	(GPTIMER_timer_regs *)TIMER4_CONFIG,
-	(GPTIMER_timer_regs *)TIMER5_CONFIG,
-	(GPTIMER_timer_regs *)TIMER6_CONFIG,
-	(GPTIMER_timer_regs *)TIMER7_CONFIG,
+	(void *)TIMER3_CONFIG,
+	(void *)TIMER4_CONFIG,
+	(void *)TIMER5_CONFIG,
+	(void *)TIMER6_CONFIG,
+	(void *)TIMER7_CONFIG,
 # if (MAX_BLACKFIN_GPTIMERS > 8)
-	(GPTIMER_timer_regs *)TIMER8_CONFIG,
-	(GPTIMER_timer_regs *)TIMER9_CONFIG,
-	(GPTIMER_timer_regs *)TIMER10_CONFIG,
+	(void *)TIMER8_CONFIG,
+	(void *)TIMER9_CONFIG,
+	(void *)TIMER10_CONFIG,
 #  if (MAX_BLACKFIN_GPTIMERS > 11)
-	(GPTIMER_timer_regs *)TIMER11_CONFIG,
+	(void *)TIMER11_CONFIG,
 #  endif
 # endif
 #endif
 };
 
-static volatile GPTIMER_group_regs *const group_regs[BFIN_TIMER_NUM_GROUP] =
+static struct bfin_gptimer_group_regs * const group_regs[BFIN_TIMER_NUM_GROUP] =
 {
-	(GPTIMER_group_regs *)TIMER0_GROUP_REG,
+	(void *)TIMER0_GROUP_REG,
 #if (MAX_BLACKFIN_GPTIMERS > 8)
-	(GPTIMER_group_regs *)TIMER8_GROUP_REG,
+	(void *)TIMER8_GROUP_REG,
 #endif
 };
 
@@ -140,7 +124,7 @@ static uint32_t const timil_mask[MAX_BLACKFIN_GPTIMERS] =
 void set_gptimer_pwidth(unsigned int timer_id, uint32_t value)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	timer_regs[timer_id]->width = value;
+	bfin_write(&timer_regs[timer_id]->width, value);
 	SSYNC();
 }
 EXPORT_SYMBOL(set_gptimer_pwidth);
@@ -148,14 +132,14 @@ EXPORT_SYMBOL(set_gptimer_pwidth);
 uint32_t get_gptimer_pwidth(unsigned int timer_id)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	return timer_regs[timer_id]->width;
+	return bfin_read(&timer_regs[timer_id]->width);
 }
 EXPORT_SYMBOL(get_gptimer_pwidth);
 
 void set_gptimer_period(unsigned int timer_id, uint32_t period)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	timer_regs[timer_id]->period = period;
+	bfin_write(&timer_regs[timer_id]->period, period);
 	SSYNC();
 }
 EXPORT_SYMBOL(set_gptimer_period);
@@ -163,71 +147,76 @@ EXPORT_SYMBOL(set_gptimer_period);
 uint32_t get_gptimer_period(unsigned int timer_id)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	return timer_regs[timer_id]->period;
+	return bfin_read(&timer_regs[timer_id]->period);
 }
 EXPORT_SYMBOL(get_gptimer_period);
 
 uint32_t get_gptimer_count(unsigned int timer_id)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	return timer_regs[timer_id]->counter;
+	return bfin_read(&timer_regs[timer_id]->counter);
 }
 EXPORT_SYMBOL(get_gptimer_count);
 
 uint32_t get_gptimer_status(unsigned int group)
 {
 	tassert(group < BFIN_TIMER_NUM_GROUP);
-	return group_regs[group]->status;
+	return bfin_read(&group_regs[group]->status);
 }
 EXPORT_SYMBOL(get_gptimer_status);
 
 void set_gptimer_status(unsigned int group, uint32_t value)
 {
 	tassert(group < BFIN_TIMER_NUM_GROUP);
-	group_regs[group]->status = value;
+	bfin_write(&group_regs[group]->status, value);
 	SSYNC();
 }
 EXPORT_SYMBOL(set_gptimer_status);
 
+static uint32_t read_gptimer_status(unsigned int timer_id)
+{
+	return bfin_read(&group_regs[BFIN_TIMER_OCTET(timer_id)]->status);
+}
+
 int get_gptimer_intr(unsigned int timer_id)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	return !!(group_regs[BFIN_TIMER_OCTET(timer_id)]->status & timil_mask[timer_id]);
+	return !!(read_gptimer_status(timer_id) & timil_mask[timer_id]);
 }
 EXPORT_SYMBOL(get_gptimer_intr);
 
 void clear_gptimer_intr(unsigned int timer_id)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	group_regs[BFIN_TIMER_OCTET(timer_id)]->status = timil_mask[timer_id];
+	bfin_write(&group_regs[BFIN_TIMER_OCTET(timer_id)]->status, timil_mask[timer_id]);
 }
 EXPORT_SYMBOL(clear_gptimer_intr);
 
 int get_gptimer_over(unsigned int timer_id)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	return !!(group_regs[BFIN_TIMER_OCTET(timer_id)]->status & tovf_mask[timer_id]);
+	return !!(read_gptimer_status(timer_id) & tovf_mask[timer_id]);
 }
 EXPORT_SYMBOL(get_gptimer_over);
 
 void clear_gptimer_over(unsigned int timer_id)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	group_regs[BFIN_TIMER_OCTET(timer_id)]->status = tovf_mask[timer_id];
+	bfin_write(&group_regs[BFIN_TIMER_OCTET(timer_id)]->status, tovf_mask[timer_id]);
 }
 EXPORT_SYMBOL(clear_gptimer_over);
 
 int get_gptimer_run(unsigned int timer_id)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	return !!(group_regs[BFIN_TIMER_OCTET(timer_id)]->status & trun_mask[timer_id]);
+	return !!(read_gptimer_status(timer_id) & trun_mask[timer_id]);
 }
 EXPORT_SYMBOL(get_gptimer_run);
 
 void set_gptimer_config(unsigned int timer_id, uint16_t config)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	timer_regs[timer_id]->config = config;
+	bfin_write(&timer_regs[timer_id]->config, config);
 	SSYNC();
 }
 EXPORT_SYMBOL(set_gptimer_config);
@@ -235,7 +224,7 @@ EXPORT_SYMBOL(set_gptimer_config);
 uint16_t get_gptimer_config(unsigned int timer_id)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	return timer_regs[timer_id]->config;
+	return bfin_read(&timer_regs[timer_id]->config);
 }
 EXPORT_SYMBOL(get_gptimer_config);
 
@@ -244,7 +233,7 @@ void enable_gptimers(uint16_t mask)
 	int i;
 	tassert((mask & ~BLACKFIN_GPTIMER_IDMASK) == 0);
 	for (i = 0; i < BFIN_TIMER_NUM_GROUP; ++i) {
-		group_regs[i]->enable = mask & 0xFF;
+		bfin_write(&group_regs[i]->enable, mask & 0xFF);
 		mask >>= 8;
 	}
 	SSYNC();
@@ -257,7 +246,7 @@ static void _disable_gptimers(uint16_t mask)
 	uint16_t m = mask;
 	tassert((mask & ~BLACKFIN_GPTIMER_IDMASK) == 0);
 	for (i = 0; i < BFIN_TIMER_NUM_GROUP; ++i) {
-		group_regs[i]->disable = m & 0xFF;
+		bfin_write(&group_regs[i]->disable, m & 0xFF);
 		m >>= 8;
 	}
 }
@@ -268,7 +257,7 @@ void disable_gptimers(uint16_t mask)
 	_disable_gptimers(mask);
 	for (i = 0; i < MAX_BLACKFIN_GPTIMERS; ++i)
 		if (mask & (1 << i))
-			group_regs[BFIN_TIMER_OCTET(i)]->status = trun_mask[i];
+			bfin_write(&group_regs[BFIN_TIMER_OCTET(i)]->status, trun_mask[i]);
 	SSYNC();
 }
 EXPORT_SYMBOL(disable_gptimers);
@@ -283,7 +272,7 @@ EXPORT_SYMBOL(disable_gptimers_sync);
 void set_gptimer_pulse_hi(unsigned int timer_id)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	timer_regs[timer_id]->config |= TIMER_PULSE_HI;
+	bfin_write_or(&timer_regs[timer_id]->config, TIMER_PULSE_HI);
 	SSYNC();
 }
 EXPORT_SYMBOL(set_gptimer_pulse_hi);
@@ -291,7 +280,7 @@ EXPORT_SYMBOL(set_gptimer_pulse_hi);
 void clear_gptimer_pulse_hi(unsigned int timer_id)
 {
 	tassert(timer_id < MAX_BLACKFIN_GPTIMERS);
-	timer_regs[timer_id]->config &= ~TIMER_PULSE_HI;
+	bfin_write_and(&timer_regs[timer_id]->config, ~TIMER_PULSE_HI);
 	SSYNC();
 }
 EXPORT_SYMBOL(clear_gptimer_pulse_hi);
@@ -301,7 +290,7 @@ uint16_t get_enabled_gptimers(void)
 	int i;
 	uint16_t result = 0;
 	for (i = 0; i < BFIN_TIMER_NUM_GROUP; ++i)
-		result |= (group_regs[i]->enable << (i << 3));
+		result |= (bfin_read(&group_regs[i]->enable) << (i << 3));
 	return result;
 }
 EXPORT_SYMBOL(get_enabled_gptimers);

arch/blackfin/kernel/process.c

@@ -140,7 +140,6 @@ EXPORT_SYMBOL(kernel_thread);
  */
 void start_thread(struct pt_regs *regs, unsigned long new_ip, unsigned long new_sp)
 {
-	set_fs(USER_DS);
 	regs->pc = new_ip;
 	if (current->mm)
 		regs->p5 = current->mm->start_data;

arch/blackfin/kernel/pwm.c

+/*
+ * Blackfin Pulse Width Modulation (PWM) core
+ *
+ * Copyright (c) 2011 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/module.h>
+#include <linux/pwm.h>
+#include <linux/slab.h>
+
+#include <asm/gptimers.h>
+#include <asm/portmux.h>
+
+struct pwm_device {
+	unsigned id;
+	unsigned short pin;
+};
+
+static const unsigned short pwm_to_gptimer_per[] = {
+	P_TMR0, P_TMR1, P_TMR2, P_TMR3, P_TMR4, P_TMR5,
+	P_TMR6, P_TMR7, P_TMR8, P_TMR9, P_TMR10, P_TMR11,
+};
+
+struct pwm_device *pwm_request(int pwm_id, const char *label)
+{
+	struct pwm_device *pwm;
+	int ret;
+
+	/* XXX: pwm_id really should be unsigned */
+	if (pwm_id < 0)
+		return NULL;
+
+	pwm = kzalloc(sizeof(*pwm), GFP_KERNEL);
+	if (!pwm)
+		return pwm;
+
+	pwm->id = pwm_id;
+	if (pwm->id >= ARRAY_SIZE(pwm_to_gptimer_per))
+		goto err;
+
+	pwm->pin = pwm_to_gptimer_per[pwm->id];
+	ret = peripheral_request(pwm->pin, label);
+	if (ret)
+		goto err;
+
+	return pwm;
+ err:
+	kfree(pwm);
+	return NULL;
+}
+EXPORT_SYMBOL(pwm_request);
+
+void pwm_free(struct pwm_device *pwm)
+{
+	peripheral_free(pwm->pin);
+	kfree(pwm);
+}
+EXPORT_SYMBOL(pwm_free);
+
+int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns)
+{
+	unsigned long period, duty;
+	unsigned long long val;
+
+	if (duty_ns < 0 || duty_ns > period_ns)
+		return -EINVAL;
+
+	val = (unsigned long long)get_sclk() * period_ns;
+	do_div(val, NSEC_PER_SEC);
+	period = val;
+
+	val = (unsigned long long)period * duty_ns;
+	do_div(val, period_ns);
+	duty = period - val;
+
+	if (duty >= period)
+		duty = period - 1;
+
+	set_gptimer_config(pwm->id, TIMER_MODE_PWM | TIMER_PERIOD_CNT);
+	set_gptimer_pwidth(pwm->id, duty);
+	set_gptimer_period(pwm->id, period);
+
+	return 0;
+}
+EXPORT_SYMBOL(pwm_config);
+
+int pwm_enable(struct pwm_device *pwm)
+{
+	enable_gptimer(pwm->id);
+	return 0;
+}
+EXPORT_SYMBOL(pwm_enable);
+
+void pwm_disable(struct pwm_device *pwm)
+{
+	disable_gptimer(pwm->id);
+}
+EXPORT_SYMBOL(pwm_disable);

arch/blackfin/kernel/reboot.c

@@ -54,6 +54,8 @@ static void bfin_reset(void)
 
 	/* The BF526 ROM will crash during reset */
 #if defined(__ADSPBF522__) || defined(__ADSPBF524__) || defined(__ADSPBF526__)
+	/* Seems to be fixed with newer parts though ... */
+	if (__SILICON_REVISION__ < 1 && bfin_revid() < 1)
 		bfin_read_SWRST();
 #endif
 

arch/blackfin/kernel/setup.c

@@ -54,8 +54,7 @@ EXPORT_SYMBOL(mtd_size);
 #endif
 
 char __initdata command_line[COMMAND_LINE_SIZE];
-void __initdata *init_retx, *init_saved_retx, *init_saved_seqstat,
-	*init_saved_icplb_fault_addr, *init_saved_dcplb_fault_addr;
+struct blackfin_initial_pda __initdata initial_pda;
 
 /* boot memmap, for parsing "memmap=" */
 #define BFIN_MEMMAP_MAX		128 /* number of entries in bfin_memmap */
@@ -957,13 +956,16 @@ void __init setup_arch(char **cmdline_p)
 		printk(KERN_EMERG "Recovering from DOUBLE FAULT event\n");
 #ifdef CONFIG_DEBUG_DOUBLEFAULT
 		/* We assume the crashing kernel, and the current symbol table match */
-		printk(KERN_EMERG " While handling exception (EXCAUSE = 0x%x) at %pF\n",
-			(int)init_saved_seqstat & SEQSTAT_EXCAUSE, init_saved_retx);
-		printk(KERN_NOTICE "   DCPLB_FAULT_ADDR: %pF\n", init_saved_dcplb_fault_addr);
-		printk(KERN_NOTICE "   ICPLB_FAULT_ADDR: %pF\n", init_saved_icplb_fault_addr);
+		printk(KERN_EMERG " While handling exception (EXCAUSE = %#x) at %pF\n",
+			initial_pda.seqstat_doublefault & SEQSTAT_EXCAUSE,
+			initial_pda.retx_doublefault);
+		printk(KERN_NOTICE "   DCPLB_FAULT_ADDR: %pF\n",
+			initial_pda.dcplb_doublefault_addr);
+		printk(KERN_NOTICE "   ICPLB_FAULT_ADDR: %pF\n",
+			initial_pda.icplb_doublefault_addr);
 #endif
 		printk(KERN_NOTICE " The instruction at %pF caused a double exception\n",
-			init_retx);
+			initial_pda.retx);
 	} else if (_bfin_swrst & RESET_WDOG)
 		printk(KERN_INFO "Recovering from Watchdog event\n");
 	else if (_bfin_swrst & RESET_SOFTWARE)

arch/blackfin/kernel/time.c

@@ -51,7 +51,7 @@ void __init setup_core_timer(void)
 	u32 tcount;
 
 	/* power up the timer, but don't enable it just yet */
-	bfin_write_TCNTL(1);
+	bfin_write_TCNTL(TMPWR);
 	CSYNC();
 
 	/* the TSCALE prescaler counter */
@@ -64,7 +64,7 @@ void __init setup_core_timer(void)
 	/* now enable the timer */
 	CSYNC();
 
-	bfin_write_TCNTL(7);
+	bfin_write_TCNTL(TAUTORLD | TMREN | TMPWR);
 }
 #endif
 

arch/blackfin/kernel/vmlinux.lds.S

@@ -155,6 +155,7 @@ SECTIONS
 		SECURITY_INITCALL
 		INIT_RAM_FS
 
+		. = ALIGN(PAGE_SIZE);
 		___per_cpu_load = .;
 		PERCPU_INPUT(32)
 

arch/blackfin/mach-bf518/Kconfig

@@ -11,55 +11,75 @@ menu "BF518 Specific Configuration"
 comment "Alternative Multiplexing Scheme"
 
 choice
-	prompt "SPORT0"
-	default BF518_SPORT0_PORTG
+	prompt "PWM Channel Pins"
+	default BF518_PWM_ALL_PORTF
 	help
-	  Select PORT used for SPORT0. See Hardware Reference Manual
+	  Select pins used for the PWM channels:
+	    PWM_AH PWM_AL PWM_BH PWM_BL PWM_CH PWM_CL
 
-config BF518_SPORT0_PORTF
-	bool "PORT F"
+	  See the Hardware Reference Manual for more details.
+
+config BF518_PWM_ALL_PORTF
+	bool "PF1 - PF6"
 	help
-	  PORT F
+	  PF{1,2,3,4,5,6} <-> PWM_{AH,AL,BH,BL,CH,CL}
 
-config BF518_SPORT0_PORTG
-	bool "PORT G"
+config BF518_PWM_PORTF_PORTG
+	bool "PF11 - PF14 / PG1 - PG2"
 	help
-	  PORT G
+	  PF{11,12,13,14} <-> PWM_{AH,AL,BH,BL}
+	  PG{1,2} <-> PWM_{CH,CL}
+
 endchoice
 
 choice
-	prompt "SPORT0 TSCLK Location"
-	depends on BF518_SPORT0_PORTG
-	default BF518_SPORT0_TSCLK_PG10
+	prompt "PWM Sync Pin"
+	default BF518_PWM_SYNC_PF7
 	help
-	  Select PIN used for SPORT0_TSCLK. See Hardware Reference Manual
+	  Select the pin used for PWM_SYNC.
 
-config BF518_SPORT0_TSCLK_PG10
-	bool "PORT PG10"
-	help
-	  PORT PG10
+	  See the Hardware Reference Manual for more details.
+
+config BF518_PWM_SYNC_PF7
+	bool "PF7"
+config BF518_PWM_SYNC_PF15
+	bool "PF15"
+endchoice
 
-config BF518_SPORT0_TSCLK_PG14
-	bool "PORT PG14"
+choice
+	prompt "PWM Trip B Pin"
+	default BF518_PWM_TRIPB_PG10
 	help
-	  PORT PG14
+	  Select the pin used for PWM_TRIPB.
+
+	  See the Hardware Reference Manual for more details.
+
+config BF518_PWM_TRIPB_PG10
+	bool "PG10"
+config BF518_PWM_TRIPB_PG14
+	bool "PG14"
 endchoice
 
 choice
-	prompt "UART1"
-	default BF518_UART1_PORTF
+	prompt "PPI / Timer Pins"
+	default BF518_PPI_TMR_PG5
 	help
-	  Select PORT used for UART1. See Hardware Reference Manual
+	  Select pins used for PPI/Timer:
+	    PPICLK PPIFS1 PPIFS2
+	    TMRCLK TMR0 TMR1
 
-config BF518_UART1_PORTF
-	bool "PORT F"
+	  See the Hardware Reference Manual for more details.
+
+config BF518_PPI_TMR_PG5
+	bool "PG5 - PG7"
 	help
-	  PORT F
+	  PG{5,6,7} <-> {PPICLK/TMRCLK,TMR0/PPIFS1,TMR1/PPIFS2}
 
-config BF518_UART1_PORTG
-	bool "PORT G"
+config BF518_PPI_TMR_PG12
+	bool "PG12 - PG14"
 	help
-	  PORT G
+	  PG{12,13,14} <-> {PPICLK/TMRCLK,TMR0/PPIFS1,TMR1/PPIFS2}
+
 endchoice
 
 comment "Hysteresis/Schmitt Trigger Control"

arch/blackfin/mach-bf518/boards/ezbrd.c

@@ -187,43 +187,16 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
 };
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) \
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
-#if defined(CONFIG_NET_DSA_KSZ8893M) \
-	|| defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
-/* SPI SWITCH CHIP */
-static struct bfin5xx_spi_chip spi_switch_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-#endif
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
-static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
@@ -239,21 +212,6 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
-	 && defined(CONFIG_SND_SOC_WM8731_SPI)
-static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-#endif
-
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_MTD_M25P80) \
 	|| defined(CONFIG_MTD_M25P80_MODULE)
@@ -269,18 +227,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) \
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 #if defined(CONFIG_NET_DSA_KSZ8893M) \
 	|| defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
@@ -290,7 +236,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.bus_num = 0,
 		.chip_select = 1,
 		.platform_data = NULL,
-		.controller_data = &spi_switch_info,
 		.mode = SPI_MODE_3,
 	},
 #endif
@@ -314,7 +259,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz	= 12500000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num	= 0,
 		.chip_select  = 2,
-		.controller_data = &spi_ad7877_chip_info,
 	},
 #endif
 #if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
@@ -324,7 +268,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz	= 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num	= 0,
 		.chip_select    = 5,
-		.controller_data = &spi_wm8731_chip_info,
 		.mode = SPI_MODE_0,
 	},
 #endif
@@ -334,7 +277,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
-		.controller_data = &spidev_chip_info,
 	},
 #endif
 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
@@ -343,7 +285,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
-		.controller_data = &lq035q1_spi_chip_info,
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif

arch/blackfin/mach-bf518/boards/tcm-bf518.c

@@ -138,32 +138,16 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) \
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
 };
 #endif
 
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
-static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
@@ -179,21 +163,6 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
-	 && defined(CONFIG_SND_SOC_WM8731_SPI)
-static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-#endif
-
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_MTD_M25P80) \
 	|| defined(CONFIG_MTD_M25P80_MODULE)
@@ -209,18 +178,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) \
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
@@ -239,7 +196,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz	= 12500000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num	= 0,
 		.chip_select  = 2,
-		.controller_data = &spi_ad7877_chip_info,
 	},
 #endif
 #if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
@@ -249,7 +205,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz	= 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num	= 0,
 		.chip_select    = 5,
-		.controller_data = &spi_wm8731_chip_info,
 		.mode = SPI_MODE_0,
 	},
 #endif
@@ -259,7 +214,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
-		.controller_data = &spidev_chip_info,
 	},
 #endif
 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
@@ -268,7 +222,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
-		.controller_data = &lq035q1_spi_chip_info,
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif

arch/blackfin/mach-bf518/include/mach/anomaly.h

@@ -11,10 +11,9 @@
  */
 
 /* This file should be up to date with:
- *  - Revision E, 01/26/2010; ADSP-BF512/BF514/BF516/BF518 Blackfin Processor Anomaly List
+ *  - Revision F, 05/23/2011; ADSP-BF512/BF514/BF516/BF518 Blackfin Processor Anomaly List
  */
 
-/* We plan on not supporting 0.0 silicon, but 0.1 isn't out yet - sorry */
 #if __SILICON_REVISION__ < 0
 # error will not work on BF518 silicon version
 #endif
@@ -77,19 +76,29 @@
 /* False Hardware Error when RETI Points to Invalid Memory */
 #define ANOMALY_05000461 (1)
 /* Synchronization Problem at Startup May Cause SPORT Transmit Channels to Misalign */
-#define ANOMALY_05000462 (1)
-/* PLL Latches Incorrect Settings During Reset */
-#define ANOMALY_05000469 (1)
+#define ANOMALY_05000462 (__SILICON_REVISION__ < 2)
 /* Incorrect Default MSEL Value in PLL_CTL */
-#define ANOMALY_05000472 (1)
+#define ANOMALY_05000472 (__SILICON_REVISION__ < 2)
 /* Interrupted SPORT Receive Data Register Read Results In Underflow when SLEN > 15 */
 #define ANOMALY_05000473 (1)
 /* TESTSET Instruction Cannot Be Interrupted */
 #define ANOMALY_05000477 (1)
 /* Reads of ITEST_COMMAND and ITEST_DATA Registers Cause Cache Corruption */
 #define ANOMALY_05000481 (1)
-/* IFLUSH sucks at life */
+/* PLL Latches Incorrect Settings During Reset */
+#define ANOMALY_05000482 (__SILICON_REVISION__ < 2)
+/* PLL_CTL Change Using bfrom_SysControl() Can Result in Processor Overclocking */
+#define ANOMALY_05000485 (__SILICON_REVISION__ < 2)
+/* SPI Master Boot Can Fail Under Certain Conditions */
+#define ANOMALY_05000490 (1)
+/* Instruction Memory Stalls Can Cause IFLUSH to Fail */
 #define ANOMALY_05000491 (1)
+/* EXCPT Instruction May Be Lost If NMI Happens Simultaneously */
+#define ANOMALY_05000494 (1)
+/* CNT_COMMAND Functionality Depends on CNT_IMASK Configuration */
+#define ANOMALY_05000498 (1)
+/* RXS Bit in SPI_STAT May Become Stuck In RX DMA Modes */
+#define ANOMALY_05000501 (1)
 
 /* Anomalies that don't exist on this proc */
 #define ANOMALY_05000099 (0)
@@ -157,6 +166,5 @@
 #define ANOMALY_05000474 (0)
 #define ANOMALY_05000475 (0)
 #define ANOMALY_05000480 (0)
-#define ANOMALY_05000485 (0)
 
 #endif

arch/blackfin/mach-bf518/include/mach/portmux.h

@@ -81,9 +81,15 @@
 #define P_PPI0_D14	(P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(1))
 #define P_PPI0_D15	(P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(1))
 
+#ifndef CONFIG_BF518_PPI_TMR_PG12
+#define P_PPI0_CLK	(P_DEFINED | P_IDENT(GPIO_PG5) | P_FUNCT(1))
+#define P_PPI0_FS1	(P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(1))
+#define P_PPI0_FS2	(P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(1))
+#else
 #define P_PPI0_CLK	(P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(1))
 #define P_PPI0_FS1	(P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(1))
 #define P_PPI0_FS2	(P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(1))
+#endif
 #define P_PPI0_FS3	(P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(1))
 
 /* SPI Port Mux */
@@ -139,9 +145,15 @@
 #define P_UART1_RX	(P_DEFINED | P_IDENT(GPIO_PH7) | P_FUNCT(1))
 
 /* Timer */
+#ifndef CONFIG_BF518_PPI_TMR_PG12
 #define P_TMRCLK	(P_DEFINED | P_IDENT(GPIO_PG5) | P_FUNCT(2))
 #define P_TMR0		(P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(2))
 #define P_TMR1		(P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(2))
+#else
+#define P_TMRCLK	(P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(2))
+#define P_TMR0		(P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(2))
+#define P_TMR1		(P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(2))
+#endif
 #define P_TMR2		(P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(2))
 #define P_TMR3		(P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(2))
 #define P_TMR4		(P_DEFINED | P_IDENT(GPIO_PG9) | P_FUNCT(2))
@@ -158,23 +170,33 @@
 #define P_TWI0_SDA	(P_DONTCARE)
 
 /* PWM */
-#define P_PWM0_AH		(P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(2))
-#define P_PWM0_AL		(P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(2))
-#define P_PWM0_BH		(P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(2))
-#define P_PWM0_BL		(P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(2))
-#define P_PWM0_CH		(P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(2))
-#define P_PWM0_CL		(P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(2))
-#define P_PWM0_SYNC		(P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(2))
-
-#define P_PWM1_AH		(P_DEFINED | P_IDENT(GPIO_PF11) | P_FUNCT(2))
-#define P_PWM1_AL		(P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(2))
-#define P_PWM1_BH		(P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(2))
-#define P_PWM1_BL		(P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(2))
-#define P_PWM1_CH		(P_DEFINED | P_IDENT(GPIO_PG1) | P_FUNCT(2))
-#define P_PWM1_CL		(P_DEFINED | P_IDENT(GPIO_PG2) | P_FUNCT(2))
-#define P_PWM1_SYNC		(P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(2))
-
+#ifndef CONFIG_BF518_PWM_PORTF_PORTG
+#define P_PWM_AH		(P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(2))
+#define P_PWM_AL		(P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(2))
+#define P_PWM_BH		(P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(2))
+#define P_PWM_BL		(P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(2))
+#define P_PWM_CH		(P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(2))
+#define P_PWM_CL		(P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(2))
+#else
+#define P_PWM_AH		(P_DEFINED | P_IDENT(GPIO_PF11) | P_FUNCT(2))
+#define P_PWM_AL		(P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(2))
+#define P_PWM_BH		(P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(2))
+#define P_PWM_BL		(P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(2))
+#define P_PWM_CH		(P_DEFINED | P_IDENT(GPIO_PG1) | P_FUNCT(2))
+#define P_PWM_CL		(P_DEFINED | P_IDENT(GPIO_PG2) | P_FUNCT(2))
+#endif
+
+#ifndef CONFIG_BF518_PWM_SYNC_PF15
+#define P_PWM_SYNC		(P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(2))
+#else
+#define P_PWM_SYNC		(P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(2))
+#endif
+
+#ifndef CONFIG_BF518_PWM_TRIPB_PG14
+#define P_PWM_TRIPB		(P_DEFINED | P_IDENT(GPIO_PG10) | P_FUNCT(2))
+#else
 #define P_PWM_TRIPB		(P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(2))
+#endif
 
 /* RSI */
 #define P_RSI_DATA0		(P_DEFINED | P_IDENT(GPIO_PG3) | P_FUNCT(1))

arch/blackfin/mach-bf527/boards/ad7160eval.c

@@ -265,29 +265,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
-	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
 };
 #endif
 
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
@@ -328,7 +311,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 4,
-		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
@@ -347,7 +329,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
-		.controller_data = &spidev_chip_info,
 	},
 #endif
 };

arch/blackfin/mach-bf527/boards/cm_bf527.c

@@ -354,40 +354,16 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) \
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
-	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
 };
 #endif
 
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
-static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
@@ -403,21 +379,6 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
-	 && defined(CONFIG_SND_SOC_WM8731_SPI)
-static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-#endif
-
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_MTD_M25P80) \
 	|| defined(CONFIG_MTD_M25P80_MODULE)
@@ -433,18 +394,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) \
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
 	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
@@ -452,7 +401,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 4,
-		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
@@ -473,7 +421,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz	= 12500000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num	= 0,
 		.chip_select  = 2,
-		.controller_data = &spi_ad7877_chip_info,
 	},
 #endif
 #if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
@@ -483,7 +430,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz	= 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num	= 0,
 		.chip_select    = 5,
-		.controller_data = &spi_wm8731_chip_info,
 		.mode = SPI_MODE_0,
 	},
 #endif
@@ -493,7 +439,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
-		.controller_data = &spidev_chip_info,
 	},
 #endif
 };

arch/blackfin/mach-bf527/boards/ezbrd.c

@@ -253,32 +253,16 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (sst25wf040) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) \
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
 };
 #endif
 
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
-static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
@@ -311,35 +295,6 @@ static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
-	 && defined(CONFIG_SND_SOC_WM8731_SPI)
-static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
-static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-#endif
-
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_MTD_M25P80) \
 	|| defined(CONFIG_MTD_M25P80_MODULE)
@@ -355,18 +310,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) \
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
@@ -385,7 +328,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz	= 12500000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num	= 0,
 		.chip_select  = 2,
-		.controller_data = &spi_ad7877_chip_info,
 	},
 #endif
 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
@@ -396,7 +338,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 5,
-		.controller_data = &spi_ad7879_chip_info,
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
@@ -407,7 +348,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz	= 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num	= 0,
 		.chip_select    = 5,
-		.controller_data = &spi_wm8731_chip_info,
 		.mode = SPI_MODE_0,
 	},
 #endif
@@ -417,7 +357,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
-		.controller_data = &spidev_chip_info,
 	},
 #endif
 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
@@ -426,7 +365,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
-		.controller_data = &lq035q1_spi_chip_info,
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif

arch/blackfin/mach-bf527/boards/ezkit.c

@@ -408,6 +408,9 @@ static struct resource net2272_bfin_resources[] = {
 		.start = 0x20300000,
 		.end = 0x20300000 + 0x100,
 		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 1,
+		.flags = IORESOURCE_BUS,
 	}, {
 		.start = IRQ_PF7,
 		.end = IRQ_PF7,
@@ -448,40 +451,16 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) \
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
-	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
 };
 #endif
 
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
-static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
@@ -513,20 +492,6 @@ static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-#endif
-
 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) || \
 	defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
 
@@ -574,9 +539,25 @@ static struct resource bfin_snd_resources[][4] = {
 	BFIN_SND_RES(0),
 	BFIN_SND_RES(1),
 };
+#endif
+
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+static struct platform_device bfin_i2s_pcm = {
+	.name = "bfin-i2s-pcm-audio",
+	.id = -1,
+};
+#endif
 
-static struct platform_device bfin_pcm = {
-	.name = "bfin-pcm-audio",
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+static struct platform_device bfin_tdm_pcm = {
+	.name = "bfin-tdm-pcm-audio",
+	.id = -1,
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+static struct platform_device bfin_ac97_pcm = {
+	.name = "bfin-ac97-pcm-audio",
 	.id = -1,
 };
 #endif
@@ -605,13 +586,6 @@ static struct platform_device bfin_tdm = {
 };
 #endif
 
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
-static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-};
-#endif
-
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_MTD_M25P80) \
 	|| defined(CONFIG_MTD_M25P80_MODULE)
@@ -627,18 +601,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) \
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
 	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
@@ -647,7 +609,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.bus_num = 0,
 		.chip_select = 4,
 		.platform_data = "ad1836",
-		.controller_data = &ad1836_spi_chip_info,
 		.mode = SPI_MODE_3,
 	},
 #endif
@@ -670,7 +631,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz	= 12500000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num	= 0,
 		.chip_select  = 2,
-		.controller_data = &spi_ad7877_chip_info,
 	},
 #endif
 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
@@ -681,7 +641,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 3,
-		.controller_data = &spi_ad7879_chip_info,
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
@@ -691,7 +650,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
-		.controller_data = &spidev_chip_info,
 	},
 #endif
 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
@@ -700,7 +658,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 7,
-		.controller_data = &lq035q1_spi_chip_info,
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
@@ -1276,9 +1233,16 @@ static struct platform_device *stamp_devices[] __initdata = {
 	&ezkit_flash_device,
 #endif
 
-#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) || \
-	defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
-	&bfin_pcm,
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+	&bfin_i2s_pcm,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+	&bfin_tdm_pcm,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+	&bfin_ac97_pcm,
 #endif
 
 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)

arch/blackfin/mach-bf527/boards/tll6527m.c

@@ -314,29 +314,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) \
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 0,         /* use dma transfer with this chip*/
-/*
- * tll6527m V1.0 does not support native spi slave selects
- * hence DMA mode will not be useful since the ADC needs
- * CS to toggle for each sample and cs_change_per_word
- * seems to be removed from spi_bfin5xx.c
- */
-	.bits_per_word = 16,
 };
 #endif
 
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
@@ -359,21 +342,6 @@ static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \
-	|| defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-#endif
-
 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
 static struct platform_device bfin_i2s = {
 	.name = "bfin-i2s",
@@ -382,24 +350,7 @@ static struct platform_device bfin_i2s = {
 };
 #endif
 
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
-static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-};
-#endif
-
 #if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
-static struct bfin5xx_spi_chip spi_mcp23s08_sys_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-
-static struct bfin5xx_spi_chip spi_mcp23s08_usr_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-
 #include <linux/spi/mcp23s08.h>
 static const struct mcp23s08_platform_data bfin_mcp23s08_sys_gpio_info = {
 	.chip[0].is_present = true,
@@ -429,22 +380,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC)
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc",
-				/* Name of spi_driver for this device */
-		.max_speed_hz = 10000000,
-				/* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = EXP_GPIO_SPISEL_BASE + 0x04 + MAX_CTRL_CS,
-		 /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-		.mode = SPI_MODE_0,
-	},
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
@@ -470,7 +405,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 					/* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = EXP_GPIO_SPISEL_BASE + 0x07 + MAX_CTRL_CS,
-		.controller_data = &spi_ad7879_chip_info,
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
@@ -482,7 +416,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.bus_num = 0,
 		.chip_select = EXP_GPIO_SPISEL_BASE + 0x03 + MAX_CTRL_CS,
 		.mode = SPI_CPHA | SPI_CPOL,
-		.controller_data = &spidev_chip_info,
 	},
 #endif
 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
@@ -491,7 +424,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 20000000,
 		.bus_num = 0,
 		.chip_select = EXP_GPIO_SPISEL_BASE + 0x06 + MAX_CTRL_CS,
-		.controller_data = &lq035q1_spi_chip_info,
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
@@ -502,7 +434,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = EXP_GPIO_SPISEL_BASE + 0x01 + MAX_CTRL_CS,
-		.controller_data = &spi_mcp23s08_sys_chip_info,
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 	{
@@ -511,7 +442,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = EXP_GPIO_SPISEL_BASE + 0x02 + MAX_CTRL_CS,
-		.controller_data = &spi_mcp23s08_usr_chip_info,
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif

arch/blackfin/mach-bf527/include/mach/anomaly.h

@@ -11,8 +11,8 @@
  */
 
 /* This file should be up to date with:
- *  - Revision E, 03/15/2010; ADSP-BF526 Blackfin Processor Anomaly List
- *  - Revision H, 04/29/2010; ADSP-BF527 Blackfin Processor Anomaly List
+ *  - Revision F, 05/23/2011; ADSP-BF526 Blackfin Processor Anomaly List
+ *  - Revision I, 05/23/2011; ADSP-BF527 Blackfin Processor Anomaly List
  */
 
 #ifndef _MACH_ANOMALY_H_
@@ -57,7 +57,7 @@
 /* Incorrect Access of OTP_STATUS During otp_write() Function */
 #define ANOMALY_05000328 (_ANOMALY_BF527(< 2))
 /* Host DMA Boot Modes Are Not Functional */
-#define ANOMALY_05000330 (__SILICON_REVISION__ < 2)
+#define ANOMALY_05000330 (_ANOMALY_BF527(< 2))
 /* Disallowed Configuration Prevents Subsequent Allowed Configuration on Host DMA Port */
 #define ANOMALY_05000337 (_ANOMALY_BF527(< 2))
 /* Ethernet MAC MDIO Reads Do Not Meet IEEE Specification */
@@ -135,7 +135,7 @@
 /* Incorrect Default Internal Voltage Regulator Setting */
 #define ANOMALY_05000410 (_ANOMALY_BF527(< 2))
 /* bfrom_SysControl() Firmware Function Cannot be Used to Enter Power Saving Modes */
-#define ANOMALY_05000411 (_ANOMALY_BF526_BF527(< 1, < 2))
+#define ANOMALY_05000411 (_ANOMALY_BF526(< 1))
 /* OTP_CHECK_FOR_PREV_WRITE Bit is Not Functional in bfrom_OtpWrite() API */
 #define ANOMALY_05000414 (_ANOMALY_BF526_BF527(< 1, < 2))
 /* DEB2_URGENT Bit Not Functional */
@@ -181,11 +181,11 @@
 /* IFLUSH Instruction at End of Hardware Loop Causes Infinite Stall */
 #define ANOMALY_05000443 (1)
 /* The WURESET Bit in the SYSCR Register is not Functional */
-#define ANOMALY_05000445 (1)
-/* USB DMA Mode 1 Short Packet Data Corruption */
+#define ANOMALY_05000445 (_ANOMALY_BF527(>= 0))
+/* USB DMA Short Packet Data Corruption */
 #define ANOMALY_05000450 (1)
 /* BCODE_QUICKBOOT, BCODE_ALLBOOT, and BCODE_FULLBOOT Settings in SYSCR Register Not Functional */
-#define ANOMALY_05000451 (1)
+#define ANOMALY_05000451 (_ANOMALY_BF527(>= 0))
 /* Incorrect Default Hysteresis Setting for RESET, NMI, and BMODE Signals */
 #define ANOMALY_05000452 (_ANOMALY_BF526_BF527(< 1, >= 0))
 /* USB Receive Interrupt Is Not Generated in DMA Mode 1 */
@@ -198,19 +198,19 @@
 #define ANOMALY_05000461 (1)
 /* Synchronization Problem at Startup May Cause SPORT Transmit Channels to Misalign */
 #define ANOMALY_05000462 (1)
-/* USB Rx DMA hang */
+/* USB Rx DMA Hang */
 #define ANOMALY_05000465 (1)
 /* TxPktRdy Bit Not Set for Transmit Endpoint When Core and DMA Access USB Endpoint FIFOs Simultaneously */
 #define ANOMALY_05000466 (1)
-/* Possible RX data corruption when control & data EP FIFOs are accessed via the core */
+/* Possible USB RX Data Corruption When Control & Data EP FIFOs are Accessed via the Core */
 #define ANOMALY_05000467 (1)
 /* PLL Latches Incorrect Settings During Reset */
 #define ANOMALY_05000469 (1)
 /* Incorrect Default MSEL Value in PLL_CTL */
 #define ANOMALY_05000472 (_ANOMALY_BF526(>= 0))
-/* Interrupted 32-Bit SPORT Data Register Access Results In Underflow */
+/* Interrupted SPORT Receive Data Register Read Results In Underflow when SLEN > 15 */
 #define ANOMALY_05000473 (1)
-/* Possible Lockup Condition whem Modifying PLL from External Memory */
+/* Possible Lockup Condition when Modifying PLL from External Memory */
 #define ANOMALY_05000475 (1)
 /* TESTSET Instruction Cannot Be Interrupted */
 #define ANOMALY_05000477 (1)
@@ -219,11 +219,19 @@
 /* Possible USB Data Corruption When Multiple Endpoints Are Accessed by the Core */
 #define ANOMALY_05000483 (1)
 /* PLL_CTL Change Using bfrom_SysControl() Can Result in Processor Overclocking */
-#define ANOMALY_05000485 (_ANOMALY_BF526_BF527(< 2, < 3))
+#define ANOMALY_05000485 (_ANOMALY_BF526_BF527(< 2, >= 0))
 /* The CODEC Zero-Cross Detect Feature is not Functional */
 #define ANOMALY_05000487 (1)
-/* IFLUSH sucks at life */
+/* SPI Master Boot Can Fail Under Certain Conditions */
+#define ANOMALY_05000490 (1)
+/* Instruction Memory Stalls Can Cause IFLUSH to Fail */
 #define ANOMALY_05000491 (1)
+/* EXCPT Instruction May Be Lost If NMI Happens Simultaneously */
+#define ANOMALY_05000494 (1)
+/* CNT_COMMAND Functionality Depends on CNT_IMASK Configuration */
+#define ANOMALY_05000498 (1)
+/* RXS Bit in SPI_STAT May Become Stuck In RX DMA Modes */
+#define ANOMALY_05000501 (1)
 
 /* Anomalies that don't exist on this proc */
 #define ANOMALY_05000099 (0)

arch/blackfin/mach-bf533/boards/H8606.c

@@ -159,22 +159,6 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
 };
 #endif
 
@@ -195,24 +179,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 4,     /* actual baudrate is SCLK/(2xspeed_hz) */
-		.bus_num = 1, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 16,
 		.bus_num = 1,
 		.chip_select = 4,
-		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
 

arch/blackfin/mach-bf533/boards/blackstamp.c

@@ -102,21 +102,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
 };
 #endif
 
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
@@ -151,7 +142,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 7,
-		.controller_data = &spidev_chip_info,
 	},
 #endif
 };

arch/blackfin/mach-bf533/boards/cm_bf533.c

@@ -59,29 +59,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-/* SPI ADC chip */
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
 };
 #endif
 
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
@@ -99,24 +82,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,               /* Framework bus number */
-		.chip_select = 2,           /* Framework chip select. */
-		.platform_data = NULL,      /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 4,
-		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
 

arch/blackfin/mach-bf533/boards/ezkit.c

@@ -210,29 +210,6 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
@@ -250,24 +227,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 4,
-		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
@@ -276,7 +241,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
-		.controller_data = &spidev_chip_info,
 	},
 #endif
 };

arch/blackfin/mach-bf533/boards/ip0x.c

@@ -110,7 +110,6 @@ static struct platform_device dm9000_device2 = {
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,		/* if 1 - block!!! */
-	.bits_per_word = 8,
 };
 #endif
 

arch/blackfin/mach-bf533/boards/stamp.c

@@ -79,6 +79,9 @@ static struct resource net2272_bfin_resources[] = {
 		.start = 0x20300000,
 		.end = 0x20300000 + 0x100,
 		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 1,
+		.flags = IORESOURCE_BUS,
 	}, {
 		.start = IRQ_PF10,
 		.end = IRQ_PF10,
@@ -172,29 +175,6 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
@@ -221,7 +201,6 @@ static struct mmc_spi_platform_data bfin_mmc_spi_pdata = {
 
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
 	.pio_interrupt = 0,
 };
 #endif
@@ -240,17 +219,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
 		.modalias = "ad183x",
@@ -258,7 +226,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.bus_num = 0,
 		.chip_select = 4,
 		.platform_data = "ad1836", /* only includes chip name for the moment */
-		.controller_data = &ad1836_spi_chip_info,
 		.mode = SPI_MODE_3,
 	},
 #endif
@@ -269,7 +236,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
-		.controller_data = &spidev_chip_info,
 	},
 #endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
@@ -659,6 +625,41 @@ static struct platform_device *stamp_devices[] __initdata = {
 #endif
 };
 
+static int __init net2272_init(void)
+{
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	int ret;
+
+	/* Set PF0 to 0, PF1 to 1 make /AMS3 work properly */
+	ret = gpio_request(GPIO_PF0, "net2272");
+	if (ret)
+		return ret;
+
+	ret = gpio_request(GPIO_PF1, "net2272");
+	if (ret) {
+		gpio_free(GPIO_PF0);
+		return ret;
+	}
+
+	ret = gpio_request(GPIO_PF11, "net2272");
+	if (ret) {
+		gpio_free(GPIO_PF0);
+		gpio_free(GPIO_PF1);
+		return ret;
+	}
+
+	gpio_direction_output(GPIO_PF0, 0);
+	gpio_direction_output(GPIO_PF1, 1);
+
+	/* Reset the USB chip */
+	gpio_direction_output(GPIO_PF11, 0);
+	mdelay(2);
+	gpio_set_value(GPIO_PF11, 1);
+#endif
+
+	return 0;
+}
+
 static int __init stamp_init(void)
 {
 	int ret;
@@ -685,6 +686,9 @@ static int __init stamp_init(void)
 	}
 #endif
 
+	if (net2272_init())
+		pr_warning("unable to configure net2272; it probably won't work\n");
+
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 	return 0;
 }

arch/blackfin/mach-bf533/include/mach/anomaly.h

@@ -11,7 +11,7 @@
  */
 
 /* This file should be up to date with:
- *  - Revision F, 05/25/2010; ADSP-BF531/BF532/BF533 Blackfin Processor Anomaly List
+ *  - Revision G, 05/23/2011; ADSP-BF531/BF532/BF533 Blackfin Processor Anomaly List
  */
 
 #ifndef _MACH_ANOMALY_H_
@@ -152,7 +152,7 @@
 #define ANOMALY_05000277 (__SILICON_REVISION__ < 6)
 /* Disabling Peripherals with DMA Running May Cause DMA System Instability */
 #define ANOMALY_05000278 (__SILICON_REVISION__ < 6)
-/* False Hardware Error Exception when ISR Context Is Not Restored */
+/* False Hardware Error when ISR Context Is Not Restored */
 #define ANOMALY_05000281 (__SILICON_REVISION__ < 6)
 /* Memory DMA Corruption with 32-Bit Data and Traffic Control */
 #define ANOMALY_05000282 (__SILICON_REVISION__ < 6)
@@ -210,18 +210,25 @@
 #define ANOMALY_05000462 (1)
 /* Boot Failure When SDRAM Control Signals Toggle Coming Out Of Reset */
 #define ANOMALY_05000471 (1)
-/* Interrupted 32-Bit SPORT Data Register Access Results In Underflow */
+/* Interrupted SPORT Receive Data Register Read Results In Underflow when SLEN > 15 */
 #define ANOMALY_05000473 (1)
-/* Possible Lockup Condition whem Modifying PLL from External Memory */
+/* Possible Lockup Condition when Modifying PLL from External Memory */
 #define ANOMALY_05000475 (1)
 /* TESTSET Instruction Cannot Be Interrupted */
 #define ANOMALY_05000477 (1)
 /* Reads of ITEST_COMMAND and ITEST_DATA Registers Cause Cache Corruption */
 #define ANOMALY_05000481 (1)
-/* IFLUSH sucks at life */
+/* PLL May Latch Incorrect Values Coming Out of Reset */
+#define ANOMALY_05000489 (1)
+/* Instruction Memory Stalls Can Cause IFLUSH to Fail */
 #define ANOMALY_05000491 (1)
+/* EXCPT Instruction May Be Lost If NMI Happens Simultaneously */
+#define ANOMALY_05000494 (1)
+/* RXS Bit in SPI_STAT May Become Stuck In RX DMA Modes */
+#define ANOMALY_05000501 (1)
 
-/* These anomalies have been "phased" out of analog.com anomaly sheets and are
+/*
+ * These anomalies have been "phased" out of analog.com anomaly sheets and are
  * here to show running on older silicon just isn't feasible.
  */
 

arch/blackfin/mach-bf537/boards/cm_bf537e.c

@@ -61,29 +61,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
 };
 #endif
 
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
@@ -101,24 +84,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 4,
-		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
 
@@ -766,6 +737,24 @@ static struct platform_device *cm_bf537e_devices[] __initdata = {
 #endif
 };
 
+static int __init net2272_init(void)
+{
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	int ret;
+
+	ret = gpio_request(GPIO_PG14, "net2272");
+	if (ret)
+		return ret;
+
+	/* Reset USB Chip, PG14 */
+	gpio_direction_output(GPIO_PG14, 0);
+	mdelay(2);
+	gpio_set_value(GPIO_PG14, 1);
+#endif
+
+	return 0;
+}
+
 static int __init cm_bf537e_init(void)
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
@@ -777,6 +766,10 @@ static int __init cm_bf537e_init(void)
 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
 	irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 #endif
+
+	if (net2272_init())
+		pr_warning("unable to configure net2272; it probably won't work\n");
+
 	return 0;
 }
 

arch/blackfin/mach-bf537/boards/cm_bf537u.c

@@ -62,29 +62,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
 };
 #endif
 
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
@@ -102,24 +85,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 4,
-		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
 
@@ -731,6 +702,36 @@ static struct platform_device *cm_bf537u_devices[] __initdata = {
 #endif
 };
 
+static int __init net2272_init(void)
+{
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	int ret;
+
+	ret = gpio_request(GPIO_PH15, driver_name);
+	if (ret)
+		return ret;
+
+	ret = gpio_request(GPIO_PH13, "net2272");
+	if (ret) {
+		gpio_free(GPIO_PH15);
+		return ret;
+	}
+
+	/* Set PH15 Low make /AMS2 work properly */
+	gpio_direction_output(GPIO_PH15, 0);
+
+	/* enable CLKBUF output */
+	bfin_write_VR_CTL(bfin_read_VR_CTL() | CLKBUFOE);
+
+	/* Reset the USB chip */
+	gpio_direction_output(GPIO_PH13, 0);
+	mdelay(2);
+	gpio_set_value(GPIO_PH13, 1);
+#endif
+
+	return 0;
+}
+
 static int __init cm_bf537u_init(void)
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
@@ -742,6 +743,10 @@ static int __init cm_bf537u_init(void)
 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
 	irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 #endif
+
+	if (net2272_init())
+		pr_warning("unable to configure net2272; it probably won't work\n");
+
 	return 0;
 }
 

arch/blackfin/mach-bf537/boards/dnp5370.c

@@ -130,7 +130,6 @@ static struct platform_device asmb_flash_device = {
 
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma    = 0,	 /* use no dma transfer with this chip*/
-	.bits_per_word = 8,
 };
 
 #endif
@@ -161,7 +160,6 @@ static struct flash_platform_data bfin_spi_dataflash_data = {
 
 static struct bfin5xx_spi_chip spi_dataflash_chip_info = {
 	.enable_dma    = 0,	 /* use no dma transfer with this chip*/
-	.bits_per_word = 8,
 };
 #endif
 

arch/blackfin/mach-bf537/boards/minotaur.c

@@ -159,14 +159,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
 };
 #endif
 
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 

arch/blackfin/mach-bf537/boards/pnav10.c

@@ -184,40 +184,16 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) \
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
-	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
 };
 #endif
 
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
-static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-
 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 	.model			= 7877,
 	.vref_delay_usecs	= 50,	/* internal, no capacitor */
@@ -248,18 +224,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) \
-	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
 	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
@@ -267,7 +231,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 4,
-		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
@@ -288,7 +251,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	.max_speed_hz		= 12500000,     /* max spi clock (SCK) speed in HZ */
 	.bus_num		= 0,
 	.chip_select  		= 5,
-	.controller_data = &spi_ad7877_chip_info,
 },
 #endif
 

arch/blackfin/mach-bf537/boards/tcm_bf537.c

@@ -62,29 +62,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
 };
 #endif
 
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 8,
 };
 #endif
 
@@ -102,24 +85,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 4,
-		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
 
@@ -733,6 +704,24 @@ static struct platform_device *cm_bf537_devices[] __initdata = {
 #endif
 };
 
+static int __init net2272_init(void)
+{
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	int ret;
+
+	ret = gpio_request(GPIO_PG14, "net2272");
+	if (ret)
+		return ret;
+
+	/* Reset USB Chip, PG14 */
+	gpio_direction_output(GPIO_PG14, 0);
+	mdelay(2);
+	gpio_set_value(GPIO_PG14, 1);
+#endif
+
+	return 0;
+}
+
 static int __init tcm_bf537_init(void)
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
@@ -744,6 +733,10 @@ static int __init tcm_bf537_init(void)
 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
 	irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 #endif
+
+	if (net2272_init())
+		pr_warning("unable to configure net2272; it probably won't work\n");
+
 	return 0;
 }
 

arch/blackfin/mach-bf537/include/mach/anomaly.h

@@ -11,7 +11,7 @@
  */
 
 /* This file should be up to date with:
- *  - Revision E, 05/25/2010; ADSP-BF534/ADSP-BF536/ADSP-BF537 Blackfin Processor Anomaly List
+ *  - Revision F, 05/23/2011; ADSP-BF534/ADSP-BF536/ADSP-BF537 Blackfin Processor Anomaly List
  */
 
 #ifndef _MACH_ANOMALY_H_
@@ -44,18 +44,12 @@
 #define ANOMALY_05000119 (1)
 /* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */
 #define ANOMALY_05000122 (1)
-/* Killed 32-Bit MMR Write Leads to Next System MMR Access Thinking It Should Be 32-Bit */
-#define ANOMALY_05000157 (__SILICON_REVISION__ < 2)
 /* PPI_DELAY Not Functional in PPI Modes with 0 Frame Syncs */
 #define ANOMALY_05000180 (1)
-/* Instruction Cache Is Not Functional */
-#define ANOMALY_05000237 (__SILICON_REVISION__ < 2)
 /* If I-Cache Is On, CSYNC/SSYNC/IDLE Around Change of Control Causes Failures */
 #define ANOMALY_05000244 (__SILICON_REVISION__ < 3)
 /* False Hardware Error from an Access in the Shadow of a Conditional Branch */
 #define ANOMALY_05000245 (1)
-/* Buffered CLKIN Output Is Disabled by Default */
-#define ANOMALY_05000247 (1)
 /* Incorrect Bit Shift of Data Word in Multichannel (TDM) Mode in Certain Conditions */
 #define ANOMALY_05000250 (__SILICON_REVISION__ < 3)
 /* EMAC TX DMA Error After an Early Frame Abort */
@@ -98,7 +92,7 @@
 #define ANOMALY_05000278 (((ANOMALY_BF536 || ANOMALY_BF537) && __SILICON_REVISION__ < 3) || (ANOMALY_BF534 && __SILICON_REVISION__ < 2))
 /* SPI Master Boot Mode Does Not Work Well with Atmel Data Flash Devices */
 #define ANOMALY_05000280 (1)
-/* False Hardware Error Exception when ISR Context Is Not Restored */
+/* False Hardware Error when ISR Context Is Not Restored */
 #define ANOMALY_05000281 (__SILICON_REVISION__ < 3)
 /* Memory DMA Corruption with 32-Bit Data and Traffic Control */
 #define ANOMALY_05000282 (__SILICON_REVISION__ < 3)
@@ -162,9 +156,9 @@
 #define ANOMALY_05000461 (1)
 /* Synchronization Problem at Startup May Cause SPORT Transmit Channels to Misalign */
 #define ANOMALY_05000462 (1)
-/* Interrupted 32-Bit SPORT Data Register Access Results In Underflow */
+/* Interrupted SPORT Receive Data Register Read Results In Underflow when SLEN > 15 */
 #define ANOMALY_05000473 (1)
-/* Possible Lockup Condition whem Modifying PLL from External Memory */
+/* Possible Lockup Condition when Modifying PLL from External Memory */
 #define ANOMALY_05000475 (1)
 /* TESTSET Instruction Cannot Be Interrupted */
 #define ANOMALY_05000477 (1)
@@ -172,8 +166,26 @@
 #define ANOMALY_05000480 (__SILICON_REVISION__ < 3)
 /* Reads of ITEST_COMMAND and ITEST_DATA Registers Cause Cache Corruption */
 #define ANOMALY_05000481 (1)
-/* IFLUSH sucks at life */
+/* PLL May Latch Incorrect Values Coming Out of Reset */
+#define ANOMALY_05000489 (1)
+/* Instruction Memory Stalls Can Cause IFLUSH to Fail */
 #define ANOMALY_05000491 (1)
+/* EXCPT Instruction May Be Lost If NMI Happens Simultaneously */
+#define ANOMALY_05000494 (1)
+/* RXS Bit in SPI_STAT May Become Stuck In RX DMA Modes */
+#define ANOMALY_05000501 (1)
+
+/*
+ * These anomalies have been "phased" out of analog.com anomaly sheets and are
+ * here to show running on older silicon just isn't feasible.
+ */
+
+/* Killed 32-Bit MMR Write Leads to Next System MMR Access Thinking It Should Be 32-Bit */
+#define ANOMALY_05000157 (__SILICON_REVISION__ < 2)
+/* Instruction Cache Is Not Functional */
+#define ANOMALY_05000237 (__SILICON_REVISION__ < 2)
+/* Buffered CLKIN Output Is Disabled by Default */
+#define ANOMALY_05000247 (__SILICON_REVISION__ < 2)
 
 /* Anomalies that don't exist on this proc */
 #define ANOMALY_05000099 (0)

arch/blackfin/mach-bf538/boards/ezkit.c

@@ -502,7 +502,6 @@ static struct flash_platform_data bfin_spi_flash_data = {
 
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
 };
 #endif
 
@@ -523,13 +522,6 @@ static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 };
 #endif
 
-#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 #include <asm/bfin-lq035q1.h>
 
@@ -559,20 +551,6 @@ static struct platform_device bfin_lq035q1_device = {
 };
 #endif
 
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
-static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-};
-#endif
-
 static struct spi_board_info bf538_spi_board_info[] __initdata = {
 #if defined(CONFIG_MTD_M25P80) \
 	|| defined(CONFIG_MTD_M25P80_MODULE)
@@ -595,7 +573,6 @@ static struct spi_board_info bf538_spi_board_info[] __initdata = {
 		.max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
-		.controller_data = &spi_ad7879_chip_info,
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
@@ -605,7 +582,6 @@ static struct spi_board_info bf538_spi_board_info[] __initdata = {
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 2,
-		.controller_data = &lq035q1_spi_chip_info,
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
@@ -615,7 +591,6 @@ static struct spi_board_info bf538_spi_board_info[] __initdata = {
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
-		.controller_data = &spidev_chip_info,
 	},
 #endif
 };

arch/blackfin/mach-bf538/ext-gpio.c

 /*
  * GPIOLIB interface for BF538/9 PORT C, D, and E GPIOs
  *
- * Copyright 2009 Analog Devices Inc.
+ * Copyright 2009-2011 Analog Devices Inc.
  *
  * Licensed under the GPL-2 or later.
  */
@@ -121,3 +121,38 @@ static int __init bf538_extgpio_setup(void)
 		gpiochip_add(&bf538_porte_chip);
 }
 arch_initcall(bf538_extgpio_setup);
+
+#ifdef CONFIG_PM
+static struct {
+	u16 data, dir, inen;
+} gpio_bank_saved[3];
+
+static void __iomem * const port_bases[3] = {
+	(void *)PORTCIO,
+	(void *)PORTDIO,
+	(void *)PORTEIO,
+};
+
+void bfin_special_gpio_pm_hibernate_suspend(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(port_bases); ++i) {
+		gpio_bank_saved[i].data = read_PORTIO(port_bases[i]);
+		gpio_bank_saved[i].inen = read_PORTIO_INEN(port_bases[i]);
+		gpio_bank_saved[i].dir = read_PORTIO_DIR(port_bases[i]);
+	}
+}
+
+void bfin_special_gpio_pm_hibernate_restore(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(port_bases); ++i) {
+		write_PORTIO_INEN(port_bases[i], gpio_bank_saved[i].inen);
+		write_PORTIO_SET(port_bases[i],
+			gpio_bank_saved[i].data & gpio_bank_saved[i].dir);
+		write_PORTIO_DIR(port_bases[i], gpio_bank_saved[i].dir);
+	}
+}
+#endif

arch/blackfin/mach-bf538/include/mach/anomaly.h

@@ -11,8 +11,8 @@
  */
 
 /* This file should be up to date with:
- *  - Revision I, 05/25/2010; ADSP-BF538/BF538F Blackfin Processor Anomaly List
- *  - Revision N, 05/25/2010; ADSP-BF539/BF539F Blackfin Processor Anomaly List
+ *  - Revision J, 05/23/2011; ADSP-BF538/BF538F Blackfin Processor Anomaly List
+ *  - Revision O, 05/23/2011; ADSP-BF539/BF539F Blackfin Processor Anomaly List
  */
 
 #ifndef _MACH_ANOMALY_H_
@@ -56,25 +56,21 @@
 #define ANOMALY_05000229 (1)
 /* PPI_FS3 Is Not Driven in 2 or 3 Internal Frame Sync Transmit Modes */
 #define ANOMALY_05000233 (1)
-/* If I-Cache Is On, CSYNC/SSYNC/IDLE Around Change of Control Causes Failures */
-#define ANOMALY_05000244 (__SILICON_REVISION__ < 3)
 /* False Hardware Error from an Access in the Shadow of a Conditional Branch */
 #define ANOMALY_05000245 (1)
 /* Maximum External Clock Speed for Timers */
 #define ANOMALY_05000253 (1)
-/* DCPLB_FAULT_ADDR MMR Register May Be Corrupted */
-#define ANOMALY_05000261 (__SILICON_REVISION__ < 3)
 /* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Decrease */
 #define ANOMALY_05000270 (__SILICON_REVISION__ < 4)
 /* Certain Data Cache Writethrough Modes Fail for Vddint <= 0.9V */
-#define ANOMALY_05000272 (1)
+#define ANOMALY_05000272 (ANOMALY_BF538)
 /* Writes to Synchronous SDRAM Memory May Be Lost */
 #define ANOMALY_05000273 (__SILICON_REVISION__ < 4)
 /* Writes to an I/O Data Register One SCLK Cycle after an Edge Is Detected May Clear Interrupt */
 #define ANOMALY_05000277 (__SILICON_REVISION__ < 4)
 /* Disabling Peripherals with DMA Running May Cause DMA System Instability */
 #define ANOMALY_05000278 (__SILICON_REVISION__ < 4)
-/* False Hardware Error Exception when ISR Context Is Not Restored */
+/* False Hardware Error when ISR Context Is Not Restored */
 #define ANOMALY_05000281 (__SILICON_REVISION__ < 4)
 /* Memory DMA Corruption with 32-Bit Data and Traffic Control */
 #define ANOMALY_05000282 (__SILICON_REVISION__ < 4)
@@ -102,8 +98,10 @@
 #define ANOMALY_05000313 (__SILICON_REVISION__ < 4)
 /* Killed System MMR Write Completes Erroneously on Next System MMR Access */
 #define ANOMALY_05000315 (__SILICON_REVISION__ < 4)
+/* PFx Glitch on Write to PORTFIO or PORTFIO_TOGGLE */
+#define ANOMALY_05000317 (__SILICON_REVISION__ < 4)	/* XXX: Same as 05000318 */
 /* PFx Glitch on Write to FIO_FLAG_D or FIO_FLAG_T */
-#define ANOMALY_05000318 (ANOMALY_BF539 && __SILICON_REVISION__ < 4)
+#define ANOMALY_05000318 (__SILICON_REVISION__ < 4)	/* XXX: Same as 05000317 */
 /* Regulator Programming Blocked when Hibernate Wakeup Source Remains Active */
 #define ANOMALY_05000355 (__SILICON_REVISION__ < 5)
 /* Serial Port (SPORT) Multichannel Transmit Failure when Channel 0 Is Disabled */
@@ -134,16 +132,32 @@
 #define ANOMALY_05000461 (1)
 /* Synchronization Problem at Startup May Cause SPORT Transmit Channels to Misalign */
 #define ANOMALY_05000462 (1)
-/* Interrupted 32-Bit SPORT Data Register Access Results In Underflow */
+/* Interrupted SPORT Receive Data Register Read Results In Underflow when SLEN > 15 */
 #define ANOMALY_05000473 (1)
-/* Possible Lockup Condition whem Modifying PLL from External Memory */
+/* Possible Lockup Condition when Modifying PLL from External Memory */
 #define ANOMALY_05000475 (1)
 /* TESTSET Instruction Cannot Be Interrupted */
 #define ANOMALY_05000477 (1)
 /* Reads of ITEST_COMMAND and ITEST_DATA Registers Cause Cache Corruption */
 #define ANOMALY_05000481 (1)
-/* IFLUSH sucks at life */
+/* PLL May Latch Incorrect Values Coming Out of Reset */
+#define ANOMALY_05000489 (1)
+/* Instruction Memory Stalls Can Cause IFLUSH to Fail */
 #define ANOMALY_05000491 (1)
+/* EXCPT Instruction May Be Lost If NMI Happens Simultaneously */
+#define ANOMALY_05000494 (1)
+/* RXS Bit in SPI_STAT May Become Stuck In RX DMA Modes */
+#define ANOMALY_05000501 (1)
+
+/*
+ * These anomalies have been "phased" out of analog.com anomaly sheets and are
+ * here to show running on older silicon just isn't feasible.
+ */
+
+/* If I-Cache Is On, CSYNC/SSYNC/IDLE Around Change of Control Causes Failures */
+#define ANOMALY_05000244 (__SILICON_REVISION__ < 3)
+/* DCPLB_FAULT_ADDR MMR Register May Be Corrupted */
+#define ANOMALY_05000261 (__SILICON_REVISION__ < 3)
 
 /* Anomalies that don't exist on this proc */
 #define ANOMALY_05000099 (0)

arch/blackfin/mach-bf538/include/mach/gpio.h

@@ -8,7 +8,10 @@
 #define _MACH_GPIO_H_
 
 #define MAX_BLACKFIN_GPIOS 16
+#ifdef CONFIG_GPIOLIB
+/* We only use the special logic with GPIOLIB devices */
 #define BFIN_SPECIAL_GPIO_BANKS 3
+#endif
 
 #define GPIO_PF0	0	/* PF */
 #define GPIO_PF1	1