Commit 715116a1 authored by Michael Chan's avatar Michael Chan Committed by David S. Miller

[TG3]: Add 5709 PHY support.

Add support for the 5709 10/100 PHY.
Signed-off-by: default avatarMichael Chan <mchan@broadcom.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent b5d3772c
......@@ -1035,6 +1035,24 @@ static int tg3_phy_reset(struct tg3 *tp)
phy_reg | MII_TG3_EXT_CTRL_FIFO_ELASTIC);
}
if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5906) {
u32 phy_reg;
/* adjust output voltage */
tg3_writephy(tp, MII_TG3_EPHY_PTEST, 0x12);
if (!tg3_readphy(tp, MII_TG3_EPHY_TEST, &phy_reg)) {
u32 phy_reg2;
tg3_writephy(tp, MII_TG3_EPHY_TEST,
phy_reg | MII_TG3_EPHY_SHADOW_EN);
/* Enable auto-MDIX */
if (!tg3_readphy(tp, 0x10, &phy_reg2))
tg3_writephy(tp, 0x10, phy_reg2 | 0x4000);
tg3_writephy(tp, MII_TG3_EPHY_TEST, phy_reg);
}
}
tg3_phy_set_wirespeed(tp);
return 0;
}
......@@ -1151,8 +1169,11 @@ static void tg3_power_down_phy(struct tg3 *tp)
if (tp->tg3_flags2 & TG3_FLG2_PHY_SERDES)
return;
tg3_writephy(tp, MII_TG3_EXT_CTRL, MII_TG3_EXT_CTRL_FORCE_LED_OFF);
if (GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5906) {
tg3_writephy(tp, MII_TG3_EXT_CTRL,
MII_TG3_EXT_CTRL_FORCE_LED_OFF);
tg3_writephy(tp, MII_TG3_AUX_CTRL, 0x01b2);
}
/* The PHY should not be powered down on some chips because
* of bugs.
......@@ -1505,6 +1526,13 @@ static void tg3_aux_stat_to_speed_duplex(struct tg3 *tp, u32 val, u16 *speed, u8
break;
default:
if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5906) {
*speed = (val & MII_TG3_AUX_STAT_100) ? SPEED_100 :
SPEED_10;
*duplex = (val & MII_TG3_AUX_STAT_FULL) ? DUPLEX_FULL :
DUPLEX_HALF;
break;
}
*speed = SPEED_INVALID;
*duplex = DUPLEX_INVALID;
break;
......@@ -1787,7 +1815,7 @@ static int tg3_setup_copper_phy(struct tg3 *tp, int force_reset)
if (tp->tg3_flags & TG3_FLAG_USE_MI_INTERRUPT)
tg3_writephy(tp, MII_TG3_IMASK, ~MII_TG3_INT_LINKCHG);
else
else if (GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5906)
tg3_writephy(tp, MII_TG3_IMASK, ~0);
if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5700 ||
......@@ -6552,7 +6580,8 @@ static int tg3_reset_hw(struct tg3 *tp, int reset_phy)
if (err)
return err;
if (!(tp->tg3_flags2 & TG3_FLG2_PHY_SERDES)) {
if (!(tp->tg3_flags2 & TG3_FLG2_PHY_SERDES) &&
GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5906) {
u32 tmp;
/* Clear CRC stats. */
......
......@@ -1624,6 +1624,7 @@
#define MII_TG3_DSP_RW_PORT 0x15 /* DSP coefficient read/write port */
#define MII_TG3_DSP_ADDRESS 0x17 /* DSP address register */
#define MII_TG3_EPHY_PTEST 0x17 /* 5906 PHY register */
#define MII_TG3_AUX_CTRL 0x18 /* auxilliary control register */
......@@ -1637,6 +1638,8 @@
#define MII_TG3_AUX_STAT_100FULL 0x0500
#define MII_TG3_AUX_STAT_1000HALF 0x0600
#define MII_TG3_AUX_STAT_1000FULL 0x0700
#define MII_TG3_AUX_STAT_100 0x0008
#define MII_TG3_AUX_STAT_FULL 0x0001
#define MII_TG3_ISTAT 0x1a /* IRQ status register */
#define MII_TG3_IMASK 0x1b /* IRQ mask register */
......@@ -1647,6 +1650,9 @@
#define MII_TG3_INT_DUPLEXCHG 0x0008
#define MII_TG3_INT_ANEG_PAGE_RX 0x0400
#define MII_TG3_EPHY_TEST 0x1f /* 5906 PHY register */
#define MII_TG3_EPHY_SHADOW_EN 0x80
/* There are two ways to manage the TX descriptors on the tigon3.
* Either the descriptors are in host DMA'able memory, or they
* exist only in the cards on-chip SRAM. All 16 send bds are under
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment