Documentation: devicetree: fix reference to legacy wakeup properties

This patch marks all the reference to the legacy wakeup bindings
and replaces them with the standard "wakeup-source" property.

All these legacy property are also listed under a separate section in
the generic wakeup-source binding document.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>

Documentation/devicetree/bindings/crypto/fsl-sec4.txt

@@ -441,7 +441,7 @@ EXAMPLE:
 		regmap = <&snvs>;
 		interrupts = <0 4 0x4>
 	        linux,keycode = <116>; /* KEY_POWER */
-		wakeup;
+		wakeup-source;
 	};
 
 =====================================================================
@@ -530,7 +530,7 @@ FULL EXAMPLE
 			regmap = <&sec_mon>;
 			interrupts = <0 4 0x4>;
 			linux,keycode = <116>; /* KEY_POWER */
-			wakeup;
+			wakeup-source;
 		};
 	};
 

Documentation/devicetree/bindings/input/ads7846.txt

@@ -65,6 +65,7 @@ Optional properties:
 	pendown-gpio			GPIO handle describing the pin the !PENIRQ
 					line is connected to.
 	wakeup-source			use any event on touchscreen as wakeup event.
+					(Legacy property support: "linux,wakeup")
 
 
 Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC::
@@ -86,6 +87,6 @@ Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC::
 			ti,x-plate-ohms = /bits/ 16 <40>;
 			ti,pressure-max = /bits/ 16 <255>;
 
-			linux,wakeup;
+			wakeup-source;
 		};
 	};

Documentation/devicetree/bindings/input/gpio-keys-polled.txt

@@ -21,6 +21,7 @@ Optional subnode-properties:
 	- debounce-interval: Debouncing interval time in milliseconds.
 	  If not specified defaults to 5.
 	- wakeup-source: Boolean, button can wake-up the system.
+			 (Legacy property supported: "gpio-key,wakeup")
 
 Example nodes:
 

Documentation/devicetree/bindings/input/gpio-keys.txt

@@ -24,6 +24,7 @@ Optional subnode-properties:
 	- debounce-interval: Debouncing interval time in milliseconds.
 	  If not specified defaults to 5.
 	- wakeup-source: Boolean, button can wake-up the system.
+			 (Legacy property supported: "gpio-key,wakeup")
 	- linux,can-disable: Boolean, indicates that button is connected
 	  to dedicated (not shared) interrupt which can be disabled to
 	  suppress events from the button.

Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt

@@ -20,6 +20,7 @@ Required Properties:
 Optional Properties:
 - linux,no-autorepeat:	do no enable autorepeat feature.
 - wakeup-source:	use any event on keypad as wakeup event.
+			(Legacy property supported: "linux,wakeup")
 - debounce-delay-ms:	debounce interval in milliseconds
 - col-scan-delay-us:	delay, measured in microseconds, that is needed
 			before we can scan keypad after activating column gpio

Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt

@@ -29,7 +29,8 @@ matrix-keyboard bindings:
 - nvidia,debounce-delay-ms: delay in milliseconds per row scan for debouncing
 - nvidia,repeat-delay-ms: delay in milliseconds before repeat starts
 - nvidia,ghost-filter: enable ghost filtering for this device
-- nvidia,wakeup-source: configure keyboard as a wakeup source for suspend/resume
+- wakeup-source: configure keyboard as a wakeup source for suspend/resume
+		 (Legacy property supported: "nvidia,wakeup-source")
 
 Example:
 

Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt

@@ -37,6 +37,7 @@ PROPERTIES
 	Usage: optional
 	Value type: <bool>
 	Definition: use any event on keypad as wakeup event.
+		    (Legacy property supported: "linux,keypad-wakeup")
 
 - keypad,num-rows:
 	Usage: required

Documentation/devicetree/bindings/input/samsung-keypad.txt

@@ -38,6 +38,7 @@ Required Board Specific Properties:
 
 Optional Properties:
 - wakeup-source: use any event on keypad as wakeup event.
+		 (Legacy property supported: "linux,input-wakeup")
 
 Optional Properties specific to linux:
 - linux,keypad-no-autorepeat: do no enable autorepeat feature.
@@ -51,7 +52,7 @@ Example:
 		samsung,keypad-num-rows = <2>;
 		samsung,keypad-num-columns = <8>;
 		linux,input-no-autorepeat;
-		linux,input-wakeup;
+		wakeup-source;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&keypad_rows &keypad_columns>;

Documentation/devicetree/bindings/mfd/tc3589x.txt

@@ -56,6 +56,7 @@ Optional nodes:
    bindings/input/matrix-keymap.txt
  - linux,no-autorepeat: do no enable autorepeat feature.
  - wakeup-source: use any event on keypad as wakeup event.
+		  (Legacy property supported: "linux,wakeup")
 
 Example:
 

Documentation/devicetree/bindings/mmc/mmc.txt

@@ -67,7 +67,8 @@ polarity is in effect.
 
 Optional SDIO properties:
 - keep-power-in-suspend: Preserves card power during a suspend/resume cycle
-- enable-sdio-wakeup: Enables wake up of host system on SDIO IRQ assertion
+- wakeup-source: Enables wake up of host system on SDIO IRQ assertion
+		 (Legacy property supported: "enable-sdio-wakeup")
 
 
 MMC power sequences:
@@ -117,7 +118,7 @@ sdhci@ab000000 {
 	wp-gpios = <&gpio 70 0>;
 	max-frequency = <50000000>;
 	keep-power-in-suspend;
-	enable-sdio-wakeup;
+	wakeup-source;
 	mmc-pwrseq = <&sdhci0_pwrseq>
 }
 

Documentation/devicetree/bindings/rtc/isil,isl12057.txt

@@ -5,7 +5,7 @@ consisting of a compatible field, an address and possibly an interrupt
 line).
 
 Nonetheless, it also supports an option boolean property
-("isil,irq2-can-wakeup-machine") to handle the specific use-case found
+("wakeup-source") to handle the specific use-case found
 on at least three in-tree users of the chip (NETGEAR ReadyNAS 102, 104
 and 2120 ARM-based NAS); On those devices, the IRQ#2 pin of the chip
 (associated with the alarm supported by the driver) is not connected
@@ -22,9 +22,9 @@ Required properties supported by the device:
 
 Optional properties:
 
- - "isil,irq2-can-wakeup-machine": mark the chip as a wakeup source,
-   independently of the availability of an IRQ line connected to the
-   SoC.
+ - "wakeup-source": mark the chip as a wakeup source, independently of
+    the availability of an IRQ line connected to the SoC.
+    (Legacy property supported: "isil,irq2-can-wakeup-machine")
 
  - "interrupt-parent", "interrupts": for passing the interrupt line
    of the SoC connected to IRQ#2 of the RTC chip.
@@ -74,5 +74,5 @@ PMIC, allowing the device to be started based on configured alarm:
 	isl12057: isl12057@68 {
 		compatible = "isil,isl12057";
 		reg = <0x68>;
-		isil,irq2-can-wakeup-machine;
+		wakeup-source;
 	};

Documentation/devicetree/bindings/rtc/rtc-opal.txt

@@ -5,12 +5,13 @@ Required properties:
 - comapatible: Should be "ibm,opal-rtc"
 
 Optional properties:
-- has-tpo: Decides if the wakeup is supported or not.
+- wakeup-source: Decides if the wakeup is supported or not
+		 (Legacy property supported: "has-tpo")
 
 Example:
 	rtc {
 		compatible = "ibm,opal-rtc";
-		has-tpo;
+		wakeup-source;
 		phandle = <0x10000029>;
 		linux,phandle = <0x10000029>;
 	};