[media] technisat-usb2: added driver for Technisat's USB2.0 DVB-S/S2 receiver

This patch is adding support for Technisat's new USB2.0 DVB-S/S2 receiver
device. The development was sponsored by Technisat.

The Green led is toggle depending on the frontend-state. The Red LED is turned
on all the time.

The MAC address reading from the EEPROM along with the
LRC-method to check whether its valid.

Support for the IR-receiver of the Technisat USB2 box. The keys of
small, black remote-control are built-in, repeated key behaviour are
simulated.

The i2c-mutex of the dvb-usb-structure is used as a general mutex for
USB requests, as there are 3 threads racing for atomic requests
consisting of multiple usb-requests.

A module option is there which disables the toggling of LEDs by the
driver on certain triggers. Useful when being used in a "dark"
environment.

[mchehab@redhat.com: Fix merge conflicts with RC renaming patches]
Signed-off-by: Martin Wilks <m.wilks@technisat.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/dvb/dvb-usb/Kconfig

@@ -358,3 +358,11 @@ config DVB_USB_LME2510
 	select DVB_IX2505V if !DVB_FE_CUSTOMISE
 	help
 	  Say Y here to support the LME DM04/QQBOX DVB-S USB2.0 .
+
+config DVB_USB_TECHNISAT_USB2
+	tristate "Technisat DVB-S/S2 USB2.0 support"
+	depends on DVB_USB
+	select DVB_STB0899 if !DVB_FE_CUSTOMISE
+	select DVB_STB6100 if !DVB_FE_CUSTOMISE
+	help
+	  Say Y here to support the Technisat USB2 DVB-S/S2 device

drivers/media/dvb/dvb-usb/Makefile

@@ -91,6 +91,9 @@ obj-$(CONFIG_DVB_USB_AZ6027) += dvb-usb-az6027.o
 dvb-usb-lmedm04-objs = lmedm04.o
 obj-$(CONFIG_DVB_USB_LME2510) += dvb-usb-lmedm04.o
 
+dvb-usb-technisat-usb2-objs = technisat-usb2.o
+obj-$(CONFIG_DVB_USB_TECHNISAT_USB2) += dvb-usb-technisat-usb2.o
+
 EXTRA_CFLAGS += -Idrivers/media/dvb/dvb-core/ -Idrivers/media/dvb/frontends/
 # due to tuner-xc3028
 EXTRA_CFLAGS += -Idrivers/media/common/tuners

drivers/media/dvb/dvb-usb/dvb-usb-ids.h

@@ -312,4 +312,5 @@
 #define USB_PID_TERRATEC_DVBS2CI_V2			0x10ac
 #define USB_PID_TECHNISAT_USB2_HDCI_V1			0x0001
 #define USB_PID_TECHNISAT_USB2_HDCI_V2			0x0002
+#define USB_PID_TECHNISAT_USB2_DVB_S2			0x0500
 #endif

drivers/media/dvb/dvb-usb/dvb-usb-remote.c

@@ -246,7 +246,7 @@ static int rc_core_dvb_usb_remote_init(struct dvb_usb_device *d)
 	dev->map_name = d->props.rc.core.rc_codes;
 	dev->change_protocol = d->props.rc.core.change_protocol;
 	dev->allowed_protos = d->props.rc.core.allowed_protos;
-	dev->driver_type = RC_DRIVER_SCANCODE;
+	dev->driver_type = d->props.rc.core.driver_type;
 	usb_to_input_id(d->udev, &dev->input_id);
 	dev->input_name = "IR-receiver inside an USB DVB receiver";
 	dev->input_phys = d->rc_phys;

drivers/media/dvb/dvb-usb/dvb-usb.h

@@ -181,6 +181,7 @@ struct dvb_rc_legacy {
  * @rc_codes: name of rc codes table
  * @protocol: type of protocol(s) currently used by the driver
  * @allowed_protos: protocol(s) supported by the driver
+ * @driver_type: Used to point if a device supports raw mode
  * @change_protocol: callback to change protocol
  * @rc_query: called to query an event event.
  * @rc_interval: time in ms between two queries.
@@ -190,6 +191,7 @@ struct dvb_rc {
 	char *rc_codes;
 	u64 protocol;
 	u64 allowed_protos;
+	enum rc_driver_type driver_type;
 	int (*change_protocol)(struct rc_dev *dev, u64 rc_type);
 	char *module_name;
 	int (*rc_query) (struct dvb_usb_device *d);

drivers/media/dvb/dvb-usb/technisat-usb2.c

+/*
+ * Linux driver for Technisat DVB-S/S2 USB 2.0 device
+ *
+ * Copyright (C) 2010 Patrick Boettcher,
+ *                    Kernel Labs Inc. PO Box 745, St James, NY 11780
+ *
+ * Development was sponsored by Technisat Digital UK Limited, whose
+ * registered office is Witan Gate House 500 - 600 Witan Gate West,
+ * Milton Keynes, MK9 1SH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ * THIS PROGRAM IS PROVIDED "AS IS" AND BOTH THE COPYRIGHT HOLDER AND
+ * TECHNISAT DIGITAL UK LTD DISCLAIM ALL WARRANTIES WITH REGARD TO
+ * THIS PROGRAM INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR
+ * FITNESS FOR A PARTICULAR PURPOSE.  NEITHER THE COPYRIGHT HOLDER
+ * NOR TECHNISAT DIGITAL UK LIMITED SHALL BE LIABLE FOR ANY SPECIAL,
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER
+ * RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION
+ * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR
+ * IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS PROGRAM. See the
+ * GNU General Public License for more details.
+ */
+
+#define DVB_USB_LOG_PREFIX "technisat-usb2"
+#include "dvb-usb.h"
+
+#include "stv6110x.h"
+#include "stv090x.h"
+
+/* module parameters */
+DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr);
+
+static int debug;
+module_param(debug, int, 0644);
+MODULE_PARM_DESC(debug,
+		"set debugging level (bit-mask: 1=info,2=eeprom,4=i2c,8=rc)." \
+		DVB_USB_DEBUG_STATUS);
+
+/* disables all LED control command and
+ * also does not start the signal polling thread */
+static int disable_led_control;
+module_param(disable_led_control, int, 0444);
+MODULE_PARM_DESC(disable_led_control,
+		"disable LED control of the device "
+		"(default: 0 - LED control is active).");
+
+/* device private data */
+struct technisat_usb2_state {
+	struct dvb_usb_device *dev;
+	struct delayed_work green_led_work;
+	u8 power_state;
+
+	u16 last_scan_code;
+};
+
+/* debug print helpers */
+#define deb_info(args...)    dprintk(debug, 0x01, args)
+#define deb_eeprom(args...)  dprintk(debug, 0x02, args)
+#define deb_i2c(args...)     dprintk(debug, 0x04, args)
+#define deb_rc(args...)      dprintk(debug, 0x08, args)
+
+/* vendor requests */
+#define SET_IFCLK_TO_EXTERNAL_TSCLK_VENDOR_REQUEST 0xB3
+#define SET_FRONT_END_RESET_VENDOR_REQUEST         0xB4
+#define GET_VERSION_INFO_VENDOR_REQUEST            0xB5
+#define SET_GREEN_LED_VENDOR_REQUEST               0xB6
+#define SET_RED_LED_VENDOR_REQUEST                 0xB7
+#define GET_IR_DATA_VENDOR_REQUEST                 0xB8
+#define SET_LED_TIMER_DIVIDER_VENDOR_REQUEST       0xB9
+#define SET_USB_REENUMERATION                      0xBA
+
+/* i2c-access methods */
+#define I2C_SPEED_100KHZ_BIT 0x40
+
+#define I2C_STATUS_NAK 7
+#define I2C_STATUS_OK 8
+
+static int technisat_usb2_i2c_access(struct usb_device *udev,
+		u8 device_addr, u8 *tx, u8 txlen, u8 *rx, u8 rxlen)
+{
+	u8 b[64];
+	int ret, actual_length;
+
+	deb_i2c("i2c-access: %02x, tx: ", device_addr);
+	debug_dump(tx, txlen, deb_i2c);
+	deb_i2c(" ");
+
+	if (txlen > 62) {
+		err("i2c TX buffer can't exceed 62 bytes (dev 0x%02x)",
+				device_addr);
+		txlen = 62;
+	}
+	if (rxlen > 62) {
+		err("i2c RX buffer can't exceed 62 bytes (dev 0x%02x)",
+				device_addr);
+		txlen = 62;
+	}
+
+	b[0] = I2C_SPEED_100KHZ_BIT;
+	b[1] = device_addr << 1;
+
+	if (rx != NULL) {
+		b[0] |= rxlen;
+		b[1] |= 1;
+	}
+
+	memcpy(&b[2], tx, txlen);
+	ret = usb_bulk_msg(udev,
+			usb_sndbulkpipe(udev, 0x01),
+			b, 2 + txlen,
+			NULL, 1000);
+
+	if (ret < 0) {
+		err("i2c-error: out failed %02x = %d", device_addr, ret);
+		return -ENODEV;
+	}
+
+	ret = usb_bulk_msg(udev,
+			usb_rcvbulkpipe(udev, 0x01),
+			b, 64, &actual_length, 1000);
+	if (ret < 0) {
+		err("i2c-error: in failed %02x = %d", device_addr, ret);
+		return -ENODEV;
+	}
+
+	if (b[0] != I2C_STATUS_OK) {
+		err("i2c-error: %02x = %d", device_addr, b[0]);
+		/* handle tuner-i2c-nak */
+		if (!(b[0] == I2C_STATUS_NAK &&
+				device_addr == 0x60
+				/* && device_is_technisat_usb2 */))
+			return -ENODEV;
+	}
+
+	deb_i2c("status: %d, ", b[0]);
+
+	if (rx != NULL) {
+		memcpy(rx, &b[2], rxlen);
+
+		deb_i2c("rx (%d): ", rxlen);
+		debug_dump(rx, rxlen, deb_i2c);
+	}
+
+	deb_i2c("\n");
+
+	return 0;
+}
+
+static int technisat_usb2_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msg,
+				int num)
+{
+	int ret = 0, i;
+	struct dvb_usb_device *d = i2c_get_adapdata(adap);
+
+	/* Ensure nobody else hits the i2c bus while we're sending our
+	   sequence of messages, (such as the remote control thread) */
+	if (mutex_lock_interruptible(&d->i2c_mutex) < 0)
+		return -EAGAIN;
+
+	for (i = 0; i < num; i++) {
+		if (i+1 < num && msg[i+1].flags & I2C_M_RD) {
+			ret = technisat_usb2_i2c_access(d->udev, msg[i+1].addr,
+						msg[i].buf, msg[i].len,
+						msg[i+1].buf, msg[i+1].len);
+			if (ret != 0)
+				break;
+			i++;
+		} else {
+			ret = technisat_usb2_i2c_access(d->udev, msg[i].addr,
+						msg[i].buf, msg[i].len,
+						NULL, 0);
+			if (ret != 0)
+				break;
+		}
+	}
+
+	if (ret == 0)
+		ret = i;
+
+	mutex_unlock(&d->i2c_mutex);
+
+	return ret;
+}
+
+static u32 technisat_usb2_i2c_func(struct i2c_adapter *adapter)
+{
+	return I2C_FUNC_I2C;
+}
+
+static struct i2c_algorithm technisat_usb2_i2c_algo = {
+	.master_xfer   = technisat_usb2_i2c_xfer,
+	.functionality = technisat_usb2_i2c_func,
+};
+
+#if 0
+static void technisat_usb2_frontend_reset(struct usb_device *udev)
+{
+	usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
+			SET_FRONT_END_RESET_VENDOR_REQUEST,
+			USB_TYPE_VENDOR | USB_DIR_OUT,
+			10, 0,
+			NULL, 0, 500);
+}
+#endif
+
+/* LED control */
+enum technisat_usb2_led_state {
+	LED_OFF,
+	LED_BLINK,
+	LED_ON,
+	LED_UNDEFINED
+};
+
+static int technisat_usb2_set_led(struct dvb_usb_device *d, int red, enum technisat_usb2_led_state state)
+{
+	int ret;
+
+	u8 led[8] = {
+		red ? SET_RED_LED_VENDOR_REQUEST : SET_GREEN_LED_VENDOR_REQUEST,
+		0
+	};
+
+	if (disable_led_control && state != LED_OFF)
+		return 0;
+
+	switch (state) {
+	case LED_ON:
+		led[1] = 0x82;
+		break;
+	case LED_BLINK:
+		led[1] = 0x82;
+		if (red) {
+			led[2] = 0x02;
+			led[3] = 10;
+			led[4] = 10;
+		} else {
+			led[2] = 0xff;
+			led[3] = 50;
+			led[4] = 50;
+		}
+		led[5] = 1;
+		break;
+
+	default:
+	case LED_OFF:
+		led[1] = 0x80;
+		break;
+	}
+
+	if (mutex_lock_interruptible(&d->i2c_mutex) < 0)
+		return -EAGAIN;
+
+	ret = usb_control_msg(d->udev, usb_sndctrlpipe(d->udev, 0),
+		red ? SET_RED_LED_VENDOR_REQUEST : SET_GREEN_LED_VENDOR_REQUEST,
+		USB_TYPE_VENDOR | USB_DIR_OUT,
+		0, 0,
+		led, sizeof(led), 500);
+
+	mutex_unlock(&d->i2c_mutex);
+	return ret;
+}
+
+static int technisat_usb2_set_led_timer(struct dvb_usb_device *d, u8 red, u8 green)
+{
+	int ret;
+	u8 b = 0;
+
+	if (mutex_lock_interruptible(&d->i2c_mutex) < 0)
+		return -EAGAIN;
+
+	ret = usb_control_msg(d->udev, usb_sndctrlpipe(d->udev, 0),
+		SET_LED_TIMER_DIVIDER_VENDOR_REQUEST,
+		USB_TYPE_VENDOR | USB_DIR_OUT,
+		(red << 8) | green, 0,
+		&b, 1, 500);
+
+	mutex_unlock(&d->i2c_mutex);
+
+	return ret;
+}
+
+static void technisat_usb2_green_led_control(struct work_struct *work)
+{
+	struct technisat_usb2_state *state =
+		container_of(work, struct technisat_usb2_state, green_led_work.work);
+	struct dvb_frontend *fe = state->dev->adapter[0].fe;
+
+	if (state->power_state == 0)
+		goto schedule;
+
+	if (fe != NULL) {
+		enum fe_status status;
+
+		if (fe->ops.read_status(fe, &status) != 0)
+			goto schedule;
+
+		if (status & FE_HAS_LOCK) {
+			u32 ber;
+
+			if (fe->ops.read_ber(fe, &ber) != 0)
+				goto schedule;
+
+			if (ber > 1000)
+				technisat_usb2_set_led(state->dev, 0, LED_BLINK);
+			else
+				technisat_usb2_set_led(state->dev, 0, LED_ON);
+		} else
+			technisat_usb2_set_led(state->dev, 0, LED_OFF);
+	}
+
+schedule:
+	schedule_delayed_work(&state->green_led_work,
+			msecs_to_jiffies(500));
+}
+
+/* method to find out whether the firmware has to be downloaded or not */
+static int technisat_usb2_identify_state(struct usb_device *udev,
+		struct dvb_usb_device_properties *props,
+		struct dvb_usb_device_description **desc, int *cold)
+{
+	int ret;
+	u8 version[3];
+
+	/* first select the interface */
+	if (usb_set_interface(udev, 0, 1) != 0) {
+		err("could not set alternate setting to 0");
+	} else {
+		info("set alternate setting");
+	}
+
+	*cold = 0; /* by default do not download a firmware - just in case something is wrong */
+
+	ret = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
+		GET_VERSION_INFO_VENDOR_REQUEST,
+		USB_TYPE_VENDOR | USB_DIR_IN,
+		0, 0,
+		version, sizeof(version), 500);
+
+	if (ret < 0)
+		*cold = 1;
+	else {
+		info("firmware version: %d.%d", version[1], version[2]);
+		*cold = 0;
+	}
+
+	return 0;
+}
+
+/* power control */
+static int technisat_usb2_power_ctrl(struct dvb_usb_device *d, int level)
+{
+	struct technisat_usb2_state *state = d->priv;
+
+	state->power_state = level;
+
+	if (disable_led_control)
+		return 0;
+
+	/* green led is turned off in any case - will be turned on when tuning */
+	technisat_usb2_set_led(d, 0, LED_OFF);
+	/* red led is turned on all the time */
+	technisat_usb2_set_led(d, 1, LED_ON);
+	return 0;
+}
+
+/* mac address reading - from the eeprom */
+#if 0
+static void technisat_usb2_eeprom_dump(struct dvb_usb_device *d)
+{
+	u8 reg;
+	u8 b[16];
+	int i,j;
+
+	/* full EEPROM dump */
+	for (j = 0; j < 256 * 4; j += 16) {
+		reg = j;
+		if (technisat_usb2_i2c_access(d->udev, 0x50 + j / 256, &reg, 1, b, 16) != 0)
+			break;
+
+		deb_eeprom("EEPROM: %01x%02x: ", j / 256, reg);
+		for (i = 0; i < 16; i++)
+			deb_eeprom("%02x ", b[i]);
+		deb_eeprom("\n");
+	}
+}
+#endif
+
+static u8 technisat_usb2_calc_lrc(const u8 *b, u16 length)
+{
+	u8 lrc = 0;
+	while (--length)
+		lrc ^= *b++;
+	return lrc;
+}
+
+static int technisat_usb2_eeprom_lrc_read(struct dvb_usb_device *d,
+	u16 offset, u8 *b, u16 length, u8 tries)
+{
+	u8 bo = offset & 0xff;
+	struct i2c_msg msg[] = {
+		{
+			.addr = 0x50 | ((offset >> 8) & 0x3),
+			.buf = &bo,
+			.len = 1
+		}, {
+			.addr = 0x50 | ((offset >> 8) & 0x3),
+			.flags	= I2C_M_RD,
+			.buf = b,
+			.len = length
+		}
+	};
+
+	while (tries--) {
+		int status;
+
+		if (i2c_transfer(&d->i2c_adap, msg, 2) != 2)
+			break;
+
+		status =
+			technisat_usb2_calc_lrc(b, length - 1) == b[length - 1];
+
+		if (status)
+			return 0;
+	}
+
+	return -EREMOTEIO;
+}
+
+#define EEPROM_MAC_START 0x3f8
+#define EEPROM_MAC_TOTAL 8
+static int technisat_usb2_read_mac_address(struct dvb_usb_device *d,
+		u8 mac[])
+{
+	u8 buf[EEPROM_MAC_TOTAL];
+
+	if (technisat_usb2_eeprom_lrc_read(d, EEPROM_MAC_START,
+				buf, EEPROM_MAC_TOTAL, 4) != 0)
+		return -ENODEV;
+
+	memcpy(mac, buf, 6);
+	return 0;
+}
+
+/* frontend attach */
+static int technisat_usb2_set_voltage(struct dvb_frontend *fe,
+		fe_sec_voltage_t voltage)
+{
+	int i;
+	u8 gpio[3] = { 0 }; /* 0 = 2, 1 = 3, 2 = 4 */
+
+	gpio[2] = 1; /* high - voltage ? */
+
+	switch (voltage) {
+	case SEC_VOLTAGE_13:
+		gpio[0] = 1;
+		break;
+	case SEC_VOLTAGE_18:
+		gpio[0] = 1;
+		gpio[1] = 1;
+		break;
+	default:
+	case SEC_VOLTAGE_OFF:
+		break;
+	}
+
+	for (i = 0; i < 3; i++)
+		if (stv090x_set_gpio(fe, i+2, 0, gpio[i], 0) != 0)
+			return -EREMOTEIO;
+	return 0;
+}
+
+static struct stv090x_config technisat_usb2_stv090x_config = {
+	.device         = STV0903,
+	.demod_mode     = STV090x_SINGLE,
+	.clk_mode       = STV090x_CLK_EXT,
+
+	.xtal           = 8000000,
+	.address        = 0x68,
+
+	.ts1_mode       = STV090x_TSMODE_DVBCI,
+	.ts1_clk        = 13400000,
+	.ts1_tei        = 1,
+
+	.repeater_level = STV090x_RPTLEVEL_64,
+
+	.tuner_bbgain   = 6,
+};
+
+static struct stv6110x_config technisat_usb2_stv6110x_config = {
+    .addr           = 0x60,
+    .refclk         = 16000000,
+    .clk_div        = 2,
+};
+
+static int technisat_usb2_frontend_attach(struct dvb_usb_adapter *a)
+{
+	struct usb_device *udev = a->dev->udev;
+	int ret;
+
+	a->fe = dvb_attach(stv090x_attach, &technisat_usb2_stv090x_config,
+			&a->dev->i2c_adap, STV090x_DEMODULATOR_0);
+
+	if (a->fe) {
+		struct stv6110x_devctl *ctl;
+
+		ctl = dvb_attach(stv6110x_attach,
+				a->fe,
+				&technisat_usb2_stv6110x_config,
+				&a->dev->i2c_adap);
+
+		if (ctl) {
+			technisat_usb2_stv090x_config.tuner_init          = ctl->tuner_init;
+			technisat_usb2_stv090x_config.tuner_sleep         = ctl->tuner_sleep;
+			technisat_usb2_stv090x_config.tuner_set_mode      = ctl->tuner_set_mode;
+			technisat_usb2_stv090x_config.tuner_set_frequency = ctl->tuner_set_frequency;
+			technisat_usb2_stv090x_config.tuner_get_frequency = ctl->tuner_get_frequency;
+			technisat_usb2_stv090x_config.tuner_set_bandwidth = ctl->tuner_set_bandwidth;
+			technisat_usb2_stv090x_config.tuner_get_bandwidth = ctl->tuner_get_bandwidth;
+			technisat_usb2_stv090x_config.tuner_set_bbgain    = ctl->tuner_set_bbgain;
+			technisat_usb2_stv090x_config.tuner_get_bbgain    = ctl->tuner_get_bbgain;
+			technisat_usb2_stv090x_config.tuner_set_refclk    = ctl->tuner_set_refclk;
+			technisat_usb2_stv090x_config.tuner_get_status    = ctl->tuner_get_status;
+
+			/* call the init function once to initialize
+			   tuner's clock output divider and demod's
+			   master clock */
+			if (a->fe->ops.init)
+				a->fe->ops.init(a->fe);
+
+			if (mutex_lock_interruptible(&a->dev->i2c_mutex) < 0)
+				return -EAGAIN;
+
+			ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
+					SET_IFCLK_TO_EXTERNAL_TSCLK_VENDOR_REQUEST,
+					USB_TYPE_VENDOR | USB_DIR_OUT,
+					0, 0,
+					NULL, 0, 500);
+			mutex_unlock(&a->dev->i2c_mutex);
+
+			if (ret != 0)
+				err("could not set IF_CLK to external");
+
+			a->fe->ops.set_voltage = technisat_usb2_set_voltage;
+
+			/* if everything was successful assign a nice name to the frontend */
+			strlcpy(a->fe->ops.info.name, a->dev->desc->name,
+					sizeof(a->fe->ops.info.name));
+		} else {
+			dvb_frontend_detach(a->fe);
+			a->fe = NULL;
+		}
+	}
+
+	technisat_usb2_set_led_timer(a->dev, 1, 1);
+
+	return a->fe == NULL ? -ENODEV : 0;
+}
+
+/* Remote control */
+
+/* the device is giving providing raw IR-signals to the host mapping
+ * it only to one remote control is just the default implementation
+ */
+#define NOMINAL_IR_BIT_TRANSITION_TIME_US 889
+#define NOMINAL_IR_BIT_TIME_US (2 * NOMINAL_IR_BIT_TRANSITION_TIME_US)
+
+#define FIRMWARE_CLOCK_TICK 83333
+#define FIRMWARE_CLOCK_DIVISOR 256
+
+#define IR_PERCENT_TOLERANCE 15
+
+#define NOMINAL_IR_BIT_TRANSITION_TICKS ((NOMINAL_IR_BIT_TRANSITION_TIME_US * 1000 * 1000) / FIRMWARE_CLOCK_TICK)
+#define NOMINAL_IR_BIT_TRANSITION_TICK_COUNT (NOMINAL_IR_BIT_TRANSITION_TICKS / FIRMWARE_CLOCK_DIVISOR)
+
+#define NOMINAL_IR_BIT_TIME_TICKS ((NOMINAL_IR_BIT_TIME_US * 1000 * 1000) / FIRMWARE_CLOCK_TICK)
+#define NOMINAL_IR_BIT_TIME_TICK_COUNT (NOMINAL_IR_BIT_TIME_TICKS / FIRMWARE_CLOCK_DIVISOR)
+
+#define MINIMUM_IR_BIT_TRANSITION_TICK_COUNT (NOMINAL_IR_BIT_TRANSITION_TICK_COUNT - ((NOMINAL_IR_BIT_TRANSITION_TICK_COUNT * IR_PERCENT_TOLERANCE) / 100))
+#define MAXIMUM_IR_BIT_TRANSITION_TICK_COUNT (NOMINAL_IR_BIT_TRANSITION_TICK_COUNT + ((NOMINAL_IR_BIT_TRANSITION_TICK_COUNT * IR_PERCENT_TOLERANCE) / 100))
+
+#define MINIMUM_IR_BIT_TIME_TICK_COUNT (NOMINAL_IR_BIT_TIME_TICK_COUNT - ((NOMINAL_IR_BIT_TIME_TICK_COUNT * IR_PERCENT_TOLERANCE) / 100))
+#define MAXIMUM_IR_BIT_TIME_TICK_COUNT (NOMINAL_IR_BIT_TIME_TICK_COUNT + ((NOMINAL_IR_BIT_TIME_TICK_COUNT * IR_PERCENT_TOLERANCE) / 100))
+
+static int technisat_usb2_get_ir(struct dvb_usb_device *d)
+{
+	u8 buf[62], *b;
+	int ret;
+	struct ir_raw_event ev;
+
+	buf[0] = GET_IR_DATA_VENDOR_REQUEST;
+	buf[1] = 0x08;
+	buf[2] = 0x8f;
+	buf[3] = MINIMUM_IR_BIT_TRANSITION_TICK_COUNT;
+	buf[4] = MAXIMUM_IR_BIT_TIME_TICK_COUNT;
+
+	if (mutex_lock_interruptible(&d->i2c_mutex) < 0)
+		return -EAGAIN;
+	ret = usb_control_msg(d->udev, usb_sndctrlpipe(d->udev, 0),
+			GET_IR_DATA_VENDOR_REQUEST,
+			USB_TYPE_VENDOR | USB_DIR_OUT,
+			0, 0,
+			buf, 5, 500);
+	if (ret < 0)
+		goto unlock;
+
+	buf[1] = 0;
+	buf[2] = 0;
+	ret = usb_control_msg(d->udev, usb_rcvctrlpipe(d->udev, 0),
+			GET_IR_DATA_VENDOR_REQUEST,
+			USB_TYPE_VENDOR | USB_DIR_IN,
+			0x8080, 0,
+			buf, sizeof(buf), 500);
+
+unlock:
+	mutex_unlock(&d->i2c_mutex);
+
+	if (ret < 0)
+		return ret;
+
+	if (ret == 1)
+		return 0; /* no key pressed */
+
+	/* decoding */
+	b = buf+1;
+
+#if 0
+	deb_rc("RC: %d ", ret);
+	debug_dump(b, ret, deb_rc);
+#endif
+
+	ev.pulse = 0;
+	while (1) {
+		ev.pulse = !ev.pulse;
+		ev.duration = (*b * FIRMWARE_CLOCK_DIVISOR * FIRMWARE_CLOCK_TICK) / 1000;
+		ir_raw_event_store(d->rc_dev, &ev);
+
+		b++;
+		if (*b == 0xff) {
+			ev.pulse = 0;
+			ev.duration = 888888*2;
+			ir_raw_event_store(d->rc_dev, &ev);
+			break;
+		}
+	}
+
+	ir_raw_event_handle(d->rc_dev);
+
+	return 1;
+}
+
+static int technisat_usb2_rc_query(struct dvb_usb_device *d)
+{
+	int ret = technisat_usb2_get_ir(d);
+
+	if (ret < 0)
+		return ret;
+
+	if (ret == 0)
+		return 0;
+
+	if (!disable_led_control)
+		technisat_usb2_set_led(d, 1, LED_BLINK);
+
+	return 0;
+}
+
+/* DVB-USB and USB stuff follows */
+static struct usb_device_id technisat_usb2_id_table[] = {
+	{ USB_DEVICE(USB_VID_TECHNISAT, USB_PID_TECHNISAT_USB2_DVB_S2) },
+	{ 0 }		/* Terminating entry */
+};
+
+/* device description */
+static struct dvb_usb_device_properties technisat_usb2_devices = {
+	.caps              = DVB_USB_IS_AN_I2C_ADAPTER,
+
+	.usb_ctrl          = CYPRESS_FX2,
+
+	.identify_state    = technisat_usb2_identify_state,
+	.firmware          = "dvb-usb-SkyStar_USB_HD_FW_v17_63.HEX.fw",
+
+	.size_of_priv      = sizeof(struct technisat_usb2_state),
+
+	.i2c_algo          = &technisat_usb2_i2c_algo,
+
+	.power_ctrl        = technisat_usb2_power_ctrl,
+	.read_mac_address  = technisat_usb2_read_mac_address,
+
+	.num_adapters = 1,
+	.adapter = {
+		{
+			.frontend_attach  = technisat_usb2_frontend_attach,
+
+			.stream = {
+				.type = USB_ISOC,
+				.count = 8,
+				.endpoint = 0x2,
+				.u = {
+					.isoc = {
+						.framesperurb = 32,
+						.framesize = 2048,
+						.interval = 3,
+					}
+				}
+			},
+
+			.size_of_priv = 0,
+		},
+	},
+
+	.num_device_descs = 1,
+	.devices = {
+		{   "Technisat SkyStar USB HD (DVB-S/S2)",
+			{ &technisat_usb2_id_table[0], NULL },
+			{ NULL },
+		},
+	},
+
+	.rc.core = {
+		.rc_interval = 100,
+		.rc_codes    = RC_MAP_TECHNISAT_USB2,
+		.module_name = "technisat-usb2",
+		.rc_query    = technisat_usb2_rc_query,
+		.allowed_protos = RC_TYPE_ALL,
+		.driver_type    = RC_DRIVER_IR_RAW,
+	}
+};
+
+static int technisat_usb2_probe(struct usb_interface *intf,
+		const struct usb_device_id *id)
+{
+	struct dvb_usb_device *dev;
+
+	if (dvb_usb_device_init(intf, &technisat_usb2_devices, THIS_MODULE,
+				&dev, adapter_nr) != 0)
+		return -ENODEV;
+
+	if (dev) {
+		struct technisat_usb2_state *state = dev->priv;
+		state->dev = dev;
+
+		if (!disable_led_control) {
+			INIT_DELAYED_WORK(&state->green_led_work,
+					technisat_usb2_green_led_control);
+			schedule_delayed_work(&state->green_led_work,
+					msecs_to_jiffies(500));
+		}
+	}
+
+	return 0;
+}
+
+static void technisat_usb2_disconnect(struct usb_interface *intf)
+{
+	struct dvb_usb_device *dev = usb_get_intfdata(intf);
+
+	/* work and stuff was only created when the device is is hot-state */
+	if (dev != NULL) {
+		struct technisat_usb2_state *state = dev->priv;
+		if (state != NULL) {
+			cancel_rearming_delayed_work(&state->green_led_work);
+			flush_scheduled_work();
+		}
+	}
+
+	dvb_usb_device_exit(intf);
+}
+
+static struct usb_driver technisat_usb2_driver = {
+	.name       = "dvb_usb_technisat_usb2",
+	.probe      = technisat_usb2_probe,
+	.disconnect = technisat_usb2_disconnect,
+	.id_table   = technisat_usb2_id_table,
+};
+
+/* module stuff */
+static int __init technisat_usb2_module_init(void)
+{
+	int result = usb_register(&technisat_usb2_driver);
+	if (result) {
+		err("usb_register failed. Code %d", result);
+		return result;
+	}
+
+	return 0;
+}
+
+static void __exit technisat_usb2_module_exit(void)
+{
+	usb_deregister(&technisat_usb2_driver);
+}
+
+module_init(technisat_usb2_module_init);
+module_exit(technisat_usb2_module_exit);
+
+MODULE_AUTHOR("Patrick Boettcher <pboettcher@kernellabs.com>");
+MODULE_DESCRIPTION("Driver for Technisat DVB-S/S2 USB 2.0 device");
+MODULE_VERSION("1.0");
+MODULE_LICENSE("GPL");

drivers/media/rc/keymaps/Makefile

@@ -74,6 +74,7 @@ obj-$(CONFIG_RC_MAP) += rc-adstech-dvb-t-pci.o \
 			rc-real-audio-220-32-keys.o \
 			rc-streamzap.o \
 			rc-tbs-nec.o \
+			rc-technisat-usb2.o \
 			rc-terratec-cinergy-xs.o \
 			rc-terratec-slim.o \
 			rc-tevii-nec.o \

drivers/media/rc/keymaps/rc-technisat-usb2.c

+/* rc-technisat-usb2.c - Keytable for SkyStar HD USB
+ *
+ * Copyright (C) 2010 Patrick Boettcher,
+ *                    Kernel Labs Inc. PO Box 745, St James, NY 11780
+ *
+ * Development was sponsored by Technisat Digital UK Limited, whose
+ * registered office is Witan Gate House 500 - 600 Witan Gate West,
+ * Milton Keynes, MK9 1SH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ * THIS PROGRAM IS PROVIDED "AS IS" AND BOTH THE COPYRIGHT HOLDER AND
+ * TECHNISAT DIGITAL UK LTD DISCLAIM ALL WARRANTIES WITH REGARD TO
+ * THIS PROGRAM INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR
+ * FITNESS FOR A PARTICULAR PURPOSE.  NEITHER THE COPYRIGHT HOLDER
+ * NOR TECHNISAT DIGITAL UK LIMITED SHALL BE LIABLE FOR ANY SPECIAL,
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER
+ * RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION
+ * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR
+ * IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS PROGRAM. See the
+ * GNU General Public License for more details.
+ */
+
+#include <media/rc-map.h>
+
+static struct rc_map_table technisat_usb2[] = {
+	{0x0a0c, KEY_POWER},
+	{0x0a01, KEY_1},
+	{0x0a02, KEY_2},
+	{0x0a03, KEY_3},
+	{0x0a0d, KEY_MUTE},
+	{0x0a04, KEY_4},
+	{0x0a05, KEY_5},
+	{0x0a06, KEY_6},
+	{0x0a38, KEY_VIDEO}, /* EXT */
+	{0x0a07, KEY_7},
+	{0x0a08, KEY_8},
+	{0x0a09, KEY_9},
+	{0x0a00, KEY_0},
+	{0x0a4f, KEY_INFO},
+	{0x0a20, KEY_CHANNELUP},
+	{0x0a52, KEY_MENU},
+	{0x0a11, KEY_VOLUMEUP},
+	{0x0a57, KEY_OK},
+	{0x0a10, KEY_VOLUMEDOWN},
+	{0x0a2f, KEY_EPG},
+	{0x0a21, KEY_CHANNELDOWN},
+	{0x0a22, KEY_REFRESH},
+	{0x0a3c, KEY_TEXT},
+	{0x0a76, KEY_ENTER}, /* HOOK */
+	{0x0a0f, KEY_HELP},
+	{0x0a6b, KEY_RED},
+	{0x0a6c, KEY_GREEN},
+	{0x0a6d, KEY_YELLOW},
+	{0x0a6e, KEY_BLUE},
+	{0x0a29, KEY_STOP},
+	{0x0a23, KEY_LANGUAGE},
+	{0x0a53, KEY_TV},
+	{0x0a0a, KEY_PROGRAM},
+};
+
+static struct rc_map_list technisat_usb2_map = {
+	.map = {
+		.scan    = technisat_usb2,
+		.size    = ARRAY_SIZE(technisat_usb2),
+		.rc_type = RC_TYPE_RC5,
+		.name    = RC_MAP_TECHNISAT_USB2,
+	}
+};
+
+static int __init init_rc_map(void)
+{
+	return rc_map_register(&technisat_usb2_map);
+}
+
+static void __exit exit_rc_map(void)
+{
+	rc_map_unregister(&technisat_usb2_map);
+}
+
+module_init(init_rc_map)
+module_exit(exit_rc_map)
+
+MODULE_AUTHOR("Patrick Boettcher <pboettcher@kernellabs.com>");
+MODULE_LICENSE("GPL");

include/media/rc-map.h

@@ -131,6 +131,7 @@ void rc_map_init(void);
 #define RC_MAP_REAL_AUDIO_220_32_KEYS    "rc-real-audio-220-32-keys"
 #define RC_MAP_STREAMZAP                 "rc-streamzap"
 #define RC_MAP_TBS_NEC                   "rc-tbs-nec"
+#define RC_MAP_TECHNISAT_USB2            "rc-technisat-usb2"
 #define RC_MAP_TERRATEC_CINERGY_XS       "rc-terratec-cinergy-xs"
 #define RC_MAP_TERRATEC_SLIM             "rc-terratec-slim"
 #define RC_MAP_TEVII_NEC                 "rc-tevii-nec"