Commit 80791be1 authored by Grant Likely's avatar Grant Likely

[POWERPC] mpc5200: Allow for fixed speed MII configurations

Various improvements for configuring the MPC5200 MII link from the
device tree:
* Look for 'current-speed' property for fixed speed MII links
* Look for 'fsl,7-wire-mode' property for boards using the 7 wire mode
* move definition of private data structure out of the header file
Signed-off-by: default avatarGrant Likely <grant.likely@secretlab.ca>
Acked-by: default avatarWolfgang Grandegger <wg@grandegger.com>
parent eabd9094
......@@ -237,6 +237,17 @@ Each GPIO controller node should have the empty property gpio-controller and
according to the bit numbers in the GPIO control registers. The second cell
is for flags which is currently unsused.
8) FEC nodes
The FEC node can specify one of the following properties to configure
the MII link:
"fsl,7-wire-mode" - An empty property that specifies the link uses 7-wire
mode instead of MII
"current-speed" - Specifies that the MII should be configured for a fixed
speed. This property should contain two cells. The
first cell specifies the speed in Mbps and the second
should be '0' for half duplex and '1' for full duplex
"phy-handle" - Contains a phandle to an Ethernet PHY.
IV - Extra Notes
================
......
......@@ -43,6 +43,29 @@
#define DRIVER_NAME "mpc52xx-fec"
#define FEC5200_PHYADDR_NONE (-1)
#define FEC5200_PHYADDR_7WIRE (-2)
/* Private driver data structure */
struct mpc52xx_fec_priv {
int duplex;
int speed;
int r_irq;
int t_irq;
struct mpc52xx_fec __iomem *fec;
struct bcom_task *rx_dmatsk;
struct bcom_task *tx_dmatsk;
spinlock_t lock;
int msg_enable;
/* MDIO link details */
int phy_addr;
unsigned int phy_speed;
struct phy_device *phydev;
enum phy_state link;
};
static irqreturn_t mpc52xx_fec_interrupt(int, void *);
static irqreturn_t mpc52xx_fec_rx_interrupt(int, void *);
static irqreturn_t mpc52xx_fec_tx_interrupt(int, void *);
......@@ -223,7 +246,7 @@ static int mpc52xx_fec_phy_start(struct net_device *dev)
struct mpc52xx_fec_priv *priv = netdev_priv(dev);
int err;
if (!priv->has_phy)
if (priv->phy_addr < 0)
return 0;
err = mpc52xx_fec_init_phy(dev);
......@@ -243,7 +266,7 @@ static void mpc52xx_fec_phy_stop(struct net_device *dev)
{
struct mpc52xx_fec_priv *priv = netdev_priv(dev);
if (!priv->has_phy)
if (!priv->phydev)
return;
phy_disconnect(priv->phydev);
......@@ -255,7 +278,7 @@ static void mpc52xx_fec_phy_stop(struct net_device *dev)
static int mpc52xx_fec_phy_mii_ioctl(struct mpc52xx_fec_priv *priv,
struct mii_ioctl_data *mii_data, int cmd)
{
if (!priv->has_phy)
if (!priv->phydev)
return -ENOTSUPP;
return phy_mii_ioctl(priv->phydev, mii_data, cmd);
......@@ -265,7 +288,7 @@ static void mpc52xx_fec_phy_hw_init(struct mpc52xx_fec_priv *priv)
{
struct mpc52xx_fec __iomem *fec = priv->fec;
if (!priv->has_phy)
if (priv->phydev)
return;
out_be32(&fec->mii_speed, priv->phy_speed);
......@@ -704,7 +727,7 @@ static void mpc52xx_fec_start(struct net_device *dev)
rcntrl = FEC_RX_BUFFER_SIZE << 16; /* max frame length */
rcntrl |= FEC_RCNTRL_FCE;
if (priv->has_phy)
if (priv->phy_addr != FEC5200_PHYADDR_7WIRE)
rcntrl |= FEC_RCNTRL_MII_MODE;
if (priv->duplex == DUPLEX_FULL)
......@@ -864,7 +887,10 @@ mpc52xx_fec_probe(struct of_device *op, const struct of_device_id *match)
struct net_device *ndev;
struct mpc52xx_fec_priv *priv = NULL;
struct resource mem;
const phandle *ph;
struct device_node *phy_node;
const phandle *phy_handle;
const u32 *prop;
int prop_size;
phys_addr_t rx_fifo;
phys_addr_t tx_fifo;
......@@ -948,26 +974,37 @@ mpc52xx_fec_probe(struct of_device *op, const struct of_device_id *match)
mpc52xx_fec_get_paddr(ndev, ndev->dev_addr);
priv->msg_enable = netif_msg_init(debug, MPC52xx_MESSAGES_DEFAULT);
priv->duplex = DUPLEX_FULL;
/* is the phy present in device tree? */
ph = of_get_property(op->node, "phy-handle", NULL);
if (ph) {
const unsigned int *prop;
struct device_node *phy_dn;
priv->has_phy = 1;
/*
* Link mode configuration
*/
phy_dn = of_find_node_by_phandle(*ph);
prop = of_get_property(phy_dn, "reg", NULL);
priv->phy_addr = *prop;
/* Start with safe defaults for link connection */
priv->phy_addr = FEC5200_PHYADDR_NONE;
priv->speed = 100;
priv->duplex = DUPLEX_HALF;
priv->phy_speed = ((mpc52xx_find_ipb_freq(op->node) >> 20) / 5) << 1;
of_node_put(phy_dn);
/* the 7-wire property means don't use MII mode */
if (of_find_property(op->node, "fsl,7-wire-mode", NULL))
priv->phy_addr = FEC5200_PHYADDR_7WIRE;
/* Phy speed */
priv->phy_speed = ((mpc52xx_find_ipb_freq(op->node) >> 20) / 5) << 1;
} else {
dev_info(&ndev->dev, "can't find \"phy-handle\" in device"
" tree, using 7-wire mode\n");
/* The current speed preconfigures the speed of the MII link */
prop = of_get_property(op->node, "current-speed", &prop_size);
if (prop && (prop_size >= sizeof(u32) * 2)) {
priv->speed = prop[0];
priv->duplex = prop[1] ? DUPLEX_FULL : DUPLEX_HALF;
}
/* If there is a phy handle, setup link to that phy */
phy_handle = of_get_property(op->node, "phy-handle", &prop_size);
if (phy_handle && (prop_size >= sizeof(phandle))) {
phy_node = of_find_node_by_phandle(*phy_handle);
prop = of_get_property(phy_node, "reg", &prop_size);
if (prop && (prop_size >= sizeof(u32)))
if ((*prop >= 0) && (*prop < PHY_MAX_ADDR))
priv->phy_addr = *prop;
of_node_put(phy_node);
}
/* Hardware init */
......@@ -982,6 +1019,20 @@ mpc52xx_fec_probe(struct of_device *op, const struct of_device_id *match)
if (rv < 0)
goto probe_error;
/* Now report the link setup */
switch (priv->phy_addr) {
case FEC5200_PHYADDR_NONE:
dev_info(&ndev->dev, "Fixed speed MII link: %i%cD\n",
priv->speed, priv->duplex ? 'F' : 'H');
break;
case FEC5200_PHYADDR_7WIRE:
dev_info(&ndev->dev, "using 7-wire PHY mode\n");
break;
default:
dev_info(&ndev->dev, "Using PHY at MDIO address %i\n",
priv->phy_addr);
}
/* We're done ! */
dev_set_drvdata(&op->dev, ndev);
......
......@@ -26,25 +26,6 @@
#define FEC_WATCHDOG_TIMEOUT ((400*HZ)/1000)
struct mpc52xx_fec_priv {
int duplex;
int r_irq;
int t_irq;
struct mpc52xx_fec __iomem *fec;
struct bcom_task *rx_dmatsk;
struct bcom_task *tx_dmatsk;
spinlock_t lock;
int msg_enable;
int has_phy;
unsigned int phy_speed;
unsigned int phy_addr;
struct phy_device *phydev;
enum phy_state link;
int speed;
};
/* ======================================================================== */
/* Hardware register sets & bits */
/* ======================================================================== */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment