Commit 81b75aef authored by Felipe Balbi's avatar Felipe Balbi Committed by Greg Kroah-Hartman

serial: omap: simplify IRQ handling

quite a few changes here, though they are
pretty obvious. In summary we're making sure
to detect which interrupt type we need to
handle before calling the underlying interrupt
handling procedure.
Tested-by: default avatarShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: default avatarSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent a0f38b87
...@@ -351,33 +351,58 @@ static inline irqreturn_t serial_omap_irq(int irq, void *dev_id) ...@@ -351,33 +351,58 @@ static inline irqreturn_t serial_omap_irq(int irq, void *dev_id)
{ {
struct uart_omap_port *up = dev_id; struct uart_omap_port *up = dev_id;
unsigned int iir, lsr; unsigned int iir, lsr;
unsigned int type;
unsigned long flags; unsigned long flags;
irqreturn_t ret = IRQ_NONE;
spin_lock_irqsave(&up->port.lock, flags);
pm_runtime_get_sync(up->dev); pm_runtime_get_sync(up->dev);
iir = serial_in(up, UART_IIR); iir = serial_in(up, UART_IIR);
if (iir & UART_IIR_NO_INT) { again:
pm_runtime_mark_last_busy(up->dev); if (iir & UART_IIR_NO_INT)
pm_runtime_put_autosuspend(up->dev); goto out;
return IRQ_NONE;
}
spin_lock_irqsave(&up->port.lock, flags); ret = IRQ_HANDLED;
lsr = serial_in(up, UART_LSR); lsr = serial_in(up, UART_LSR);
if (iir & UART_IIR_RLSI) {
if (lsr & UART_LSR_DR)
receive_chars(up, &lsr);
}
/* extract IRQ type from IIR register */
type = iir & 0x3e;
switch (type) {
case UART_IIR_MSI:
check_modem_status(up); check_modem_status(up);
if ((lsr & UART_LSR_THRE) && (iir & UART_IIR_THRI)) break;
case UART_IIR_THRI:
if (lsr & UART_LSR_THRE)
transmit_chars(up); transmit_chars(up);
break;
case UART_IIR_RDI:
if (lsr & UART_LSR_DR)
receive_chars(up, &lsr);
break;
case UART_IIR_RLSI:
if (lsr & UART_LSR_BRK_ERROR_BITS)
receive_chars(up, &lsr);
break;
case UART_IIR_RX_TIMEOUT:
receive_chars(up, &lsr);
break;
case UART_IIR_CTS_RTS_DSR:
iir = serial_in(up, UART_IIR);
goto again;
case UART_IIR_XOFF:
/* FALLTHROUGH */
default:
break;
}
out:
spin_unlock_irqrestore(&up->port.lock, flags); spin_unlock_irqrestore(&up->port.lock, flags);
pm_runtime_mark_last_busy(up->dev); pm_runtime_mark_last_busy(up->dev);
pm_runtime_put_autosuspend(up->dev); pm_runtime_put_autosuspend(up->dev);
up->port_activity = jiffies; up->port_activity = jiffies;
return IRQ_HANDLED;
return ret;
} }
static unsigned int serial_omap_tx_empty(struct uart_port *port) static unsigned int serial_omap_tx_empty(struct uart_port *port)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment