hwmon: Correct some typos

Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

drivers/hwmon/abituguru.c

@@ -164,7 +164,7 @@ static const u8 abituguru_bank2_max_threshold = 50;
 static const int abituguru_pwm_settings_multiplier[5] = { 0, 1, 1, 1000, 1000 };
 /*
  * Min / Max allowed values for pwm_settings. Note: pwm1 (CPU fan) is a
- * special case the minium allowed pwm% setting for this is 30% (77) on
+ * special case the minimum allowed pwm% setting for this is 30% (77) on
  * some MB's this special case is handled in the code!
  */
 static const u8 abituguru_pwm_min[5] = { 0, 170, 170, 25, 25 };
@@ -517,7 +517,7 @@ abituguru_detect_bank1_sensor_type(struct abituguru_data *data,
 
 	ABIT_UGURU_DEBUG(2, "testing bank1 sensor %d\n", (int)sensor_addr);
 	/*
-	 * Volt sensor test, enable volt low alarm, set min value ridicously
+	 * Volt sensor test, enable volt low alarm, set min value ridiculously
 	 * high, or vica versa if the reading is very high. If its a volt
 	 * sensor this should always give us an alarm.
 	 */
@@ -564,7 +564,7 @@ abituguru_detect_bank1_sensor_type(struct abituguru_data *data,
 
 	/*
 	 * Temp sensor test, enable sensor as a temp sensor, set beep value
-	 * ridicously low (but not too low, otherwise uguru ignores it).
+	 * ridiculously low (but not too low, otherwise uguru ignores it).
 	 * If its a temp sensor this should always give us an alarm.
 	 */
 	buf[0] = ABIT_UGURU_TEMP_HIGH_ALARM_ENABLE;

drivers/hwmon/abituguru3.c

@@ -176,7 +176,7 @@ struct abituguru3_data {
 
 	/*
 	 * The abituguru3 supports up to 48 sensors, and thus has registers
-	 * sets for 48 sensors, for convienence reasons / simplicity of the
+	 * sets for 48 sensors, for convenience reasons / simplicity of the
 	 * code we always read and store all registers for all 48 sensors
 	 */
 

drivers/hwmon/asus_atk0110.c

@@ -119,7 +119,7 @@ struct atk_data {
 	acpi_handle rtmp_handle;
 	acpi_handle rvlt_handle;
 	acpi_handle rfan_handle;
-	/* new inteface */
+	/* new interface */
 	acpi_handle enumerate_handle;
 	acpi_handle read_handle;
 	acpi_handle write_handle;

drivers/hwmon/max6650.c

@@ -660,7 +660,7 @@ static int max6650_init_client(struct i2c_client *client)
 	/*
 	 * If mode is set to "full off", we change it to "open loop" and
 	 * set DAC to 255, which has the same effect. We do this because
-	 * there's no "full off" mode defined in hwmon specifcations.
+	 * there's no "full off" mode defined in hwmon specifications.
 	 */
 
 	if ((config & MAX6650_CFG_MODE_MASK) == MAX6650_CFG_MODE_OFF) {

drivers/hwmon/pmbus/pmbus_core.c

@@ -157,7 +157,7 @@ EXPORT_SYMBOL_GPL(pmbus_write_byte);
 
 /*
  * _pmbus_write_byte() is similar to pmbus_write_byte(), but checks if
- * a device specific mapping funcion exists and calls it if necessary.
+ * a device specific mapping function exists and calls it if necessary.
  */
 static int _pmbus_write_byte(struct i2c_client *client, int page, u8 value)
 {

drivers/hwmon/w83791d.c

@@ -1043,7 +1043,7 @@ static struct sensor_device_attribute sda_temp_alarm[] = {
 	SENSOR_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 13),
 };
 
-/* get reatime status of all sensors items: voltage, temp, fan */
+/* get realtime status of all sensors items: voltage, temp, fan */
 static ssize_t show_alarms_reg(struct device *dev,
 				struct device_attribute *attr, char *buf)
 {

drivers/hwmon/w83792d.c

@@ -579,7 +579,7 @@ static ssize_t store_temp23(struct device *dev, struct device_attribute *attr,
 	return count;
 }
 
-/* get reatime status of all sensors items: voltage, temp, fan */
+/* get realtime status of all sensors items: voltage, temp, fan */
 static ssize_t
 show_alarms_reg(struct device *dev, struct device_attribute *attr, char *buf)
 {

drivers/hwmon/w83793.c

@@ -808,7 +808,7 @@ show_sf_ctrl(struct device *dev, struct device_attribute *attr, char *buf)
 	if (nr == TEMP_FAN_MAP) {
 		val = data->temp_fan_map[index];
 	} else if (nr == TEMP_PWM_ENABLE) {
-		/* +2 to transfrom into 2 and 3 to conform with sysfs intf */
+		/* +2 to transform into 2 and 3 to conform with sysfs intf */
 		val = ((data->pwm_enable >> index) & 0x01) + 2;
 	} else if (nr == TEMP_CRUISE) {
 		val = TEMP_FROM_REG(data->temp_cruise[index] & 0x7f);