Merge remote-tracking branch 'spi/topic/qspi' into spi-next

Documentation/devicetree/bindings/spi/ti_qspi.txt

+TI QSPI controller.
+
+Required properties:
+- compatible : should be "ti,dra7xxx-qspi" or "ti,am4372-qspi".
+- reg: Should contain QSPI registers location and length.
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+- ti,hwmods: Name of the hwmod associated to the QSPI
+
+Recommended properties:
+- spi-max-frequency: Definition as per
+                     Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Example:
+
+qspi: qspi@4b300000 {
+	compatible = "ti,dra7xxx-qspi";
+	reg = <0x4b300000 0x100>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	spi-max-frequency = <25000000>;
+	ti,hwmods = "qspi";
+};

drivers/spi/Kconfig

@@ -306,6 +306,14 @@ config SPI_OMAP24XX
 	  SPI master controller for OMAP24XX and later Multichannel SPI
 	  (McSPI) modules.
 
+config SPI_TI_QSPI
+	tristate "DRA7xxx QSPI controller support"
+	depends on ARCH_OMAP2PLUS || COMPILE_TEST
+	help
+	  QSPI master controller for DRA7xxx used for flash devices.
+	  This device supports single, dual and quad read support, while
+	  it only supports single write mode.
+
 config SPI_OMAP_100K
 	tristate "OMAP SPI 100K"
 	depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST

drivers/spi/Makefile

@@ -49,6 +49,7 @@ obj-$(CONFIG_SPI_OCTEON)		+= spi-octeon.o
 obj-$(CONFIG_SPI_OMAP_UWIRE)		+= spi-omap-uwire.o
 obj-$(CONFIG_SPI_OMAP_100K)		+= spi-omap-100k.o
 obj-$(CONFIG_SPI_OMAP24XX)		+= spi-omap2-mcspi.o
+obj-$(CONFIG_SPI_TI_QSPI)		+= spi-ti-qspi.o
 obj-$(CONFIG_SPI_ORION)			+= spi-orion.o
 obj-$(CONFIG_SPI_PL022)			+= spi-pl022.o
 obj-$(CONFIG_SPI_PPC4xx)		+= spi-ppc4xx.o

drivers/spi/spi-bcm63xx.c

@@ -231,24 +231,6 @@ static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *first,
 	return 0;
 }
 
-static int bcm63xx_spi_prepare_transfer(struct spi_master *master)
-{
-	struct bcm63xx_spi *bs = spi_master_get_devdata(master);
-
-	pm_runtime_get_sync(&bs->pdev->dev);
-
-	return 0;
-}
-
-static int bcm63xx_spi_unprepare_transfer(struct spi_master *master)
-{
-	struct bcm63xx_spi *bs = spi_master_get_devdata(master);
-
-	pm_runtime_put(&bs->pdev->dev);
-
-	return 0;
-}
-
 static int bcm63xx_spi_transfer_one(struct spi_master *master,
 					struct spi_message *m)
 {
@@ -406,11 +388,10 @@ static int bcm63xx_spi_probe(struct platform_device *pdev)
 
 	master->bus_num = pdata->bus_num;
 	master->num_chipselect = pdata->num_chipselect;
-	master->prepare_transfer_hardware = bcm63xx_spi_prepare_transfer;
-	master->unprepare_transfer_hardware = bcm63xx_spi_unprepare_transfer;
 	master->transfer_one_message = bcm63xx_spi_transfer_one;
 	master->mode_bits = MODEBITS;
 	master->bits_per_word_mask = SPI_BPW_MASK(8);
+	master->auto_runtime_pm = true;
 	bs->msg_type_shift = pdata->msg_type_shift;
 	bs->msg_ctl_width = pdata->msg_ctl_width;
 	bs->tx_io = (u8 *)(bs->regs + bcm63xx_spireg(SPI_MSG_DATA));

drivers/spi/spi-coldfire-qspi.c

@@ -354,24 +354,6 @@ static int mcfqspi_transfer_one_message(struct spi_master *master,
 
 }
 
-static int mcfqspi_prepare_transfer_hw(struct spi_master *master)
-{
-	struct mcfqspi *mcfqspi = spi_master_get_devdata(master);
-
-	pm_runtime_get_sync(mcfqspi->dev);
-
-	return 0;
-}
-
-static int mcfqspi_unprepare_transfer_hw(struct spi_master *master)
-{
-	struct mcfqspi *mcfqspi = spi_master_get_devdata(master);
-
-	pm_runtime_put_sync(mcfqspi->dev);
-
-	return 0;
-}
-
 static int mcfqspi_setup(struct spi_device *spi)
 {
 	if (spi->chip_select >= spi->master->num_chipselect) {
@@ -473,8 +455,7 @@ static int mcfqspi_probe(struct platform_device *pdev)
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 16);
 	master->setup = mcfqspi_setup;
 	master->transfer_one_message = mcfqspi_transfer_one_message;
-	master->prepare_transfer_hardware = mcfqspi_prepare_transfer_hw;
-	master->unprepare_transfer_hardware = mcfqspi_unprepare_transfer_hw;
+	master->auto_runtime_pm = true;
 
 	platform_set_drvdata(pdev, master);
 

drivers/spi/spi-omap2-mcspi.c

@@ -335,23 +335,6 @@ static void omap2_mcspi_restore_ctx(struct omap2_mcspi *mcspi)
 		__raw_writel(cs->chconf0, cs->base + OMAP2_MCSPI_CHCONF0);
 }
 
-static int omap2_prepare_transfer(struct spi_master *master)
-{
-	struct omap2_mcspi *mcspi = spi_master_get_devdata(master);
-
-	pm_runtime_get_sync(mcspi->dev);
-	return 0;
-}
-
-static int omap2_unprepare_transfer(struct spi_master *master)
-{
-	struct omap2_mcspi *mcspi = spi_master_get_devdata(master);
-
-	pm_runtime_mark_last_busy(mcspi->dev);
-	pm_runtime_put_autosuspend(mcspi->dev);
-	return 0;
-}
-
 static int mcspi_wait_for_reg_bit(void __iomem *reg, unsigned long bit)
 {
 	unsigned long timeout;
@@ -1318,8 +1301,7 @@ static int omap2_mcspi_probe(struct platform_device *pdev)
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
 	master->setup = omap2_mcspi_setup;
-	master->prepare_transfer_hardware = omap2_prepare_transfer;
-	master->unprepare_transfer_hardware = omap2_unprepare_transfer;
+	master->auto_runtime_pm = true;
 	master->transfer_one_message = omap2_mcspi_transfer_one_message;
 	master->cleanup = omap2_mcspi_cleanup;
 	master->dev.of_node = node;

drivers/spi/spi-pl022.c

@@ -1555,18 +1555,6 @@ static int pl022_transfer_one_message(struct spi_master *master,
 	return 0;
 }
 
-static int pl022_prepare_transfer_hardware(struct spi_master *master)
-{
-	struct pl022 *pl022 = spi_master_get_devdata(master);
-
-	/*
-	 * Just make sure we have all we need to run the transfer by syncing
-	 * with the runtime PM framework.
-	 */
-	pm_runtime_get_sync(&pl022->adev->dev);
-	return 0;
-}
-
 static int pl022_unprepare_transfer_hardware(struct spi_master *master)
 {
 	struct pl022 *pl022 = spi_master_get_devdata(master);
@@ -1575,13 +1563,6 @@ static int pl022_unprepare_transfer_hardware(struct spi_master *master)
 	writew((readw(SSP_CR1(pl022->virtbase)) &
 		(~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase));
 
-	if (pl022->master_info->autosuspend_delay > 0) {
-		pm_runtime_mark_last_busy(&pl022->adev->dev);
-		pm_runtime_put_autosuspend(&pl022->adev->dev);
-	} else {
-		pm_runtime_put(&pl022->adev->dev);
-	}
-
 	return 0;
 }
 
@@ -2140,7 +2121,7 @@ static int pl022_probe(struct amba_device *adev, const struct amba_id *id)
 	master->num_chipselect = num_cs;
 	master->cleanup = pl022_cleanup;
 	master->setup = pl022_setup;
-	master->prepare_transfer_hardware = pl022_prepare_transfer_hardware;
+	master->auto_runtime_pm = true;
 	master->transfer_one_message = pl022_transfer_one_message;
 	master->unprepare_transfer_hardware = pl022_unprepare_transfer_hardware;
 	master->rt = platform_info->rt;

drivers/spi/spi-pxa2xx.c

@@ -811,14 +811,6 @@ static int pxa2xx_spi_transfer_one_message(struct spi_master *master,
 	return 0;
 }
 
-static int pxa2xx_spi_prepare_transfer(struct spi_master *master)
-{
-	struct driver_data *drv_data = spi_master_get_devdata(master);
-
-	pm_runtime_get_sync(&drv_data->pdev->dev);
-	return 0;
-}
-
 static int pxa2xx_spi_unprepare_transfer(struct spi_master *master)
 {
 	struct driver_data *drv_data = spi_master_get_devdata(master);
@@ -827,8 +819,6 @@ static int pxa2xx_spi_unprepare_transfer(struct spi_master *master)
 	write_SSCR0(read_SSCR0(drv_data->ioaddr) & ~SSCR0_SSE,
 		    drv_data->ioaddr);
 
-	pm_runtime_mark_last_busy(&drv_data->pdev->dev);
-	pm_runtime_put_autosuspend(&drv_data->pdev->dev);
 	return 0;
 }
 
@@ -1141,8 +1131,8 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 	master->cleanup = cleanup;
 	master->setup = setup;
 	master->transfer_one_message = pxa2xx_spi_transfer_one_message;
-	master->prepare_transfer_hardware = pxa2xx_spi_prepare_transfer;
 	master->unprepare_transfer_hardware = pxa2xx_spi_unprepare_transfer;
+	master->auto_runtime_pm = true;
 
 	drv_data->ssp_type = ssp->type;
 	drv_data->null_dma_buf = (u32 *)PTR_ALIGN(&drv_data[1], DMA_ALIGNMENT);

drivers/spi/spi-s3c64xx.c

@@ -356,8 +356,6 @@ static int s3c64xx_spi_prepare_transfer(struct spi_master *spi)
 	while (!is_polling(sdd) && !acquire_dma(sdd))
 		usleep_range(10000, 11000);
 
-	pm_runtime_get_sync(&sdd->pdev->dev);
-
 	return 0;
 }
 
@@ -372,7 +370,6 @@ static int s3c64xx_spi_unprepare_transfer(struct spi_master *spi)
 		sdd->ops->release((enum dma_ch)sdd->tx_dma.ch,
 					&s3c64xx_spi_dma_client);
 	}
-	pm_runtime_put(&sdd->pdev->dev);
 
 	return 0;
 }
@@ -1395,6 +1392,7 @@ static int s3c64xx_spi_probe(struct platform_device *pdev)
 					SPI_BPW_MASK(8);
 	/* the spi->mode bits understood by this driver: */
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+	master->auto_runtime_pm = true;
 
 	sdd->regs = devm_ioremap_resource(&pdev->dev, mem_res);
 	if (IS_ERR(sdd->regs)) {

drivers/spi/spi-sh-hspi.c

@@ -99,21 +99,6 @@ static int hspi_status_check_timeout(struct hspi_priv *hspi, u32 mask, u32 val)
 /*
  *		spi master function
  */
-static int hspi_prepare_transfer(struct spi_master *master)
-{
-	struct hspi_priv *hspi = spi_master_get_devdata(master);
-
-	pm_runtime_get_sync(hspi->dev);
-	return 0;
-}
-
-static int hspi_unprepare_transfer(struct spi_master *master)
-{
-	struct hspi_priv *hspi = spi_master_get_devdata(master);
-
-	pm_runtime_put_sync(hspi->dev);
-	return 0;
-}
 
 #define hspi_hw_cs_enable(hspi)		hspi_hw_cs_ctrl(hspi, 0)
 #define hspi_hw_cs_disable(hspi)	hspi_hw_cs_ctrl(hspi, 1)
@@ -316,9 +301,8 @@ static int hspi_probe(struct platform_device *pdev)
 	master->setup		= hspi_setup;
 	master->cleanup		= hspi_cleanup;
 	master->mode_bits	= SPI_CPOL | SPI_CPHA;
-	master->prepare_transfer_hardware	= hspi_prepare_transfer;
+	master->auto_runtime_pm = true;
 	master->transfer_one_message		= hspi_transfer_one_message;
-	master->unprepare_transfer_hardware	= hspi_unprepare_transfer;
 	ret = spi_register_master(master);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "spi_register_master error.\n");

drivers/spi/spi-tegra114.c

@@ -816,14 +816,6 @@ static int tegra_spi_transfer_one_message(struct spi_master *master,
 	msg->status = 0;
 	msg->actual_length = 0;
 
-	ret = pm_runtime_get_sync(tspi->dev);
-	if (ret < 0) {
-		dev_err(tspi->dev, "runtime PM get failed: %d\n", ret);
-		msg->status = ret;
-		spi_finalize_current_message(master);
-		return ret;
-	}
-
 	single_xfer = list_is_singular(&msg->transfers);
 	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
 		INIT_COMPLETION(tspi->xfer_completion);
@@ -859,7 +851,6 @@ static int tegra_spi_transfer_one_message(struct spi_master *master,
 	ret = 0;
 exit:
 	tegra_spi_writel(tspi, tspi->def_command1_reg, SPI_COMMAND1);
-	pm_runtime_put(tspi->dev);
 	msg->status = ret;
 	spi_finalize_current_message(master);
 	return ret;
@@ -1053,6 +1044,7 @@ static int tegra_spi_probe(struct platform_device *pdev)
 	master->transfer_one_message = tegra_spi_transfer_one_message;
 	master->num_chipselect = MAX_CHIP_SELECT;
 	master->bus_num = -1;
+	master->auto_runtime_pm = true;
 
 	tspi->master = master;
 	tspi->dev = &pdev->dev;

drivers/spi/spi-tegra20-sflash.c

@@ -335,12 +335,6 @@ static int tegra_sflash_transfer_one_message(struct spi_master *master,
 	struct spi_device *spi = msg->spi;
 	int ret;
 
-	ret = pm_runtime_get_sync(tsd->dev);
-	if (ret < 0) {
-		dev_err(tsd->dev, "pm_runtime_get() failed, err = %d\n", ret);
-		return ret;
-	}
-
 	msg->status = 0;
 	msg->actual_length = 0;
 	single_xfer = list_is_singular(&msg->transfers);
@@ -380,7 +374,6 @@ static int tegra_sflash_transfer_one_message(struct spi_master *master,
 	tegra_sflash_writel(tsd, tsd->def_command_reg, SPI_COMMAND);
 	msg->status = ret;
 	spi_finalize_current_message(master);
-	pm_runtime_put(tsd->dev);
 	return ret;
 }
 
@@ -477,6 +470,7 @@ static int tegra_sflash_probe(struct platform_device *pdev)
 	master->mode_bits = SPI_CPOL | SPI_CPHA;
 	master->setup = tegra_sflash_setup;
 	master->transfer_one_message = tegra_sflash_transfer_one_message;
+	master->auto_runtime_pm = true;
 	master->num_chipselect = MAX_CHIP_SELECT;
 	master->bus_num = -1;
 

drivers/spi/spi-tegra20-slink.c

@@ -836,11 +836,6 @@ static int tegra_slink_transfer_one_message(struct spi_master *master,
 
 	msg->status = 0;
 	msg->actual_length = 0;
-	ret = pm_runtime_get_sync(tspi->dev);
-	if (ret < 0) {
-		dev_err(tspi->dev, "runtime get failed: %d\n", ret);
-		goto done;
-	}
 
 	single_xfer = list_is_singular(&msg->transfers);
 	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
@@ -878,8 +873,6 @@ static int tegra_slink_transfer_one_message(struct spi_master *master,
 exit:
 	tegra_slink_writel(tspi, tspi->def_command_reg, SLINK_COMMAND);
 	tegra_slink_writel(tspi, tspi->def_command2_reg, SLINK_COMMAND2);
-	pm_runtime_put(tspi->dev);
-done:
 	msg->status = ret;
 	spi_finalize_current_message(master);
 	return ret;
@@ -1086,6 +1079,7 @@ static int tegra_slink_probe(struct platform_device *pdev)
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
 	master->setup = tegra_slink_setup;
 	master->transfer_one_message = tegra_slink_transfer_one_message;
+	master->auto_runtime_pm = true;
 	master->num_chipselect = MAX_CHIP_SELECT;
 	master->bus_num = -1;
 

drivers/spi/spi.c

@@ -553,6 +553,10 @@ static void spi_pump_messages(struct kthread_work *work)
 		    master->unprepare_transfer_hardware(master))
 			dev_err(&master->dev,
 				"failed to unprepare transfer hardware\n");
+		if (master->auto_runtime_pm) {
+			pm_runtime_mark_last_busy(master->dev.parent);
+			pm_runtime_put_autosuspend(master->dev.parent);
+		}
 		return;
 	}
 
@@ -572,11 +576,23 @@ static void spi_pump_messages(struct kthread_work *work)
 		master->busy = true;
 	spin_unlock_irqrestore(&master->queue_lock, flags);
 
+	if (!was_busy && master->auto_runtime_pm) {
+		ret = pm_runtime_get_sync(master->dev.parent);
+		if (ret < 0) {
+			dev_err(&master->dev, "Failed to power device: %d\n",
+				ret);
+			return;
+		}
+	}
+
 	if (!was_busy && master->prepare_transfer_hardware) {
 		ret = master->prepare_transfer_hardware(master);
 		if (ret) {
 			dev_err(&master->dev,
 				"failed to prepare transfer hardware\n");
+
+			if (master->auto_runtime_pm)
+				pm_runtime_put(master->dev.parent);
 			return;
 		}
 	}
@@ -869,6 +885,51 @@ static void of_register_spi_devices(struct spi_master *master)
 		if (of_find_property(nc, "spi-3wire", NULL))
 			spi->mode |= SPI_3WIRE;
 
+		/* Device DUAL/QUAD mode */
+		prop = of_get_property(nc, "spi-tx-nbits", &len);
+		if (!prop || len < sizeof(*prop)) {
+			dev_err(&master->dev, "%s has no 'spi-tx-nbits' property\n",
+				nc->full_name);
+			spi_dev_put(spi);
+			continue;
+		}
+		switch (be32_to_cpup(prop)) {
+		case SPI_NBITS_SINGLE:
+			break;
+		case SPI_NBITS_DUAL:
+			spi->mode |= SPI_TX_DUAL;
+			break;
+		case SPI_NBITS_QUAD:
+			spi->mode |= SPI_TX_QUAD;
+			break;
+		default:
+			dev_err(&master->dev, "spi-tx-nbits value is not supported\n");
+			spi_dev_put(spi);
+			continue;
+		}
+
+		prop = of_get_property(nc, "spi-rx-nbits", &len);
+		if (!prop || len < sizeof(*prop)) {
+			dev_err(&master->dev, "%s has no 'spi-rx-nbits' property\n",
+				nc->full_name);
+			spi_dev_put(spi);
+			continue;
+		}
+		switch (be32_to_cpup(prop)) {
+		case SPI_NBITS_SINGLE:
+			break;
+		case SPI_NBITS_DUAL:
+			spi->mode |= SPI_RX_DUAL;
+			break;
+		case SPI_NBITS_QUAD:
+			spi->mode |= SPI_RX_QUAD;
+			break;
+		default:
+			dev_err(&master->dev, "spi-rx-nbits value is not supported\n");
+			spi_dev_put(spi);
+			continue;
+		}
+
 		/* Device speed */
 		prop = of_get_property(nc, "spi-max-frequency", &len);
 		if (!prop || len < sizeof(*prop)) {
@@ -1316,6 +1377,19 @@ int spi_setup(struct spi_device *spi)
 	unsigned	bad_bits;
 	int		status = 0;
 
+	/* check mode to prevent that DUAL and QUAD set at the same time
+	 */
+	if (((spi->mode & SPI_TX_DUAL) && (spi->mode & SPI_TX_QUAD)) ||
+		((spi->mode & SPI_RX_DUAL) && (spi->mode & SPI_RX_QUAD))) {
+		dev_err(&spi->dev,
+		"setup: can not select dual and quad at the same time\n");
+		return -EINVAL;
+	}
+	/* if it is SPI_3WIRE mode, DUAL and QUAD should be forbidden
+	 */
+	if ((spi->mode & SPI_3WIRE) && (spi->mode &
+		(SPI_TX_DUAL | SPI_TX_QUAD | SPI_RX_DUAL | SPI_RX_QUAD)))
+		return -EINVAL;
 	/* help drivers fail *cleanly* when they need options
 	 * that aren't supported with their current master
 	 */
@@ -1378,6 +1452,8 @@ static int __spi_async(struct spi_device *spi, struct spi_message *message)
 	/**
 	 * Set transfer bits_per_word and max speed as spi device default if
 	 * it is not set for this transfer.
+	 * Set transfer tx_nbits and rx_nbits as single transfer default
+	 * (SPI_NBITS_SINGLE) if it is not set for this transfer.
 	 */
 	list_for_each_entry(xfer, &message->transfers, transfer_list) {
 		message->frame_length += xfer->len;
@@ -1404,7 +1480,47 @@ static int __spi_async(struct spi_device *spi, struct spi_message *message)
 			return -EINVAL;
 		if (xfer->speed_hz && master->max_speed_hz &&
 		    xfer->speed_hz > master->max_speed_hz)
+
+		if (xfer->tx_buf && !xfer->tx_nbits)
+			xfer->tx_nbits = SPI_NBITS_SINGLE;
+		if (xfer->rx_buf && !xfer->rx_nbits)
+			xfer->rx_nbits = SPI_NBITS_SINGLE;
+		/* check transfer tx/rx_nbits:
+		 * 1. keep the value is not out of single, dual and quad
+		 * 2. keep tx/rx_nbits is contained by mode in spi_device
+		 * 3. if SPI_3WIRE, tx/rx_nbits should be in single
+		 */
+		if (xfer->tx_buf) {
+			if (xfer->tx_nbits != SPI_NBITS_SINGLE &&
+				xfer->tx_nbits != SPI_NBITS_DUAL &&
+				xfer->tx_nbits != SPI_NBITS_QUAD)
+				return -EINVAL;
+			if ((xfer->tx_nbits == SPI_NBITS_DUAL) &&
+				!(spi->mode & (SPI_TX_DUAL | SPI_TX_QUAD)))
+				return -EINVAL;
+			if ((xfer->tx_nbits == SPI_NBITS_QUAD) &&
+				!(spi->mode & SPI_TX_QUAD))
+				return -EINVAL;
+			if ((spi->mode & SPI_3WIRE) &&
+				(xfer->tx_nbits != SPI_NBITS_SINGLE))
+				return -EINVAL;
+		}
+		/* check transfer rx_nbits */
+		if (xfer->rx_buf) {
+			if (xfer->rx_nbits != SPI_NBITS_SINGLE &&
+				xfer->rx_nbits != SPI_NBITS_DUAL &&
+				xfer->rx_nbits != SPI_NBITS_QUAD)
+				return -EINVAL;
+			if ((xfer->rx_nbits == SPI_NBITS_DUAL) &&
+				!(spi->mode & (SPI_RX_DUAL | SPI_RX_QUAD)))
+				return -EINVAL;
+			if ((xfer->rx_nbits == SPI_NBITS_QUAD) &&
+				!(spi->mode & SPI_RX_QUAD))
 				return -EINVAL;
+			if ((spi->mode & SPI_3WIRE) &&
+				(xfer->rx_nbits != SPI_NBITS_SINGLE))
+				return -EINVAL;
+		}
 	}
 
 	message->spi = spi;

include/linux/spi/spi.h

@@ -74,7 +74,7 @@ struct spi_device {
 	struct spi_master	*master;
 	u32			max_speed_hz;
 	u8			chip_select;
-	u8			mode;
+	u16			mode;
 #define	SPI_CPHA	0x01			/* clock phase */
 #define	SPI_CPOL	0x02			/* clock polarity */
 #define	SPI_MODE_0	(0|0)			/* (original MicroWire) */
@@ -87,6 +87,10 @@ struct spi_device {
 #define	SPI_LOOP	0x20			/* loopback mode */
 #define	SPI_NO_CS	0x40			/* 1 dev/bus, no chipselect */
 #define	SPI_READY	0x80			/* slave pulls low to pause */
+#define	SPI_TX_DUAL	0x100			/* transmit with 2 wires */
+#define	SPI_TX_QUAD	0x200			/* transmit with 4 wires */
+#define	SPI_RX_DUAL	0x400			/* receive with 2 wires */
+#define	SPI_RX_QUAD	0x800			/* receive with 4 wires */
 	u8			bits_per_word;
 	int			irq;
 	void			*controller_state;
@@ -256,6 +260,9 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv)
  * @busy: message pump is busy
  * @running: message pump is running
  * @rt: whether this queue is set to run as a realtime task
+ * @auto_runtime_pm: the core should ensure a runtime PM reference is held
+ *                   while the hardware is prepared, using the parent
+ *                   device for the spidev
  * @prepare_transfer_hardware: a message will soon arrive from the queue
  *	so the subsystem requests the driver to prepare the transfer hardware
  *	by issuing this call
@@ -380,11 +387,13 @@ struct spi_master {
 	bool				busy;
 	bool				running;
 	bool				rt;
+	bool				auto_runtime_pm;
 
 	int (*prepare_transfer_hardware)(struct spi_master *master);
 	int (*transfer_one_message)(struct spi_master *master,
 				    struct spi_message *mesg);
 	int (*unprepare_transfer_hardware)(struct spi_master *master);
+
 	/* gpio chip select */
 	int			*cs_gpios;
 };
@@ -454,6 +463,10 @@ extern struct spi_master *spi_busnum_to_master(u16 busnum);
  * @rx_buf: data to be read (dma-safe memory), or NULL
  * @tx_dma: DMA address of tx_buf, if @spi_message.is_dma_mapped
  * @rx_dma: DMA address of rx_buf, if @spi_message.is_dma_mapped
+ * @tx_nbits: number of bits used for writting. If 0 the default
+ *      (SPI_NBITS_SINGLE) is used.
+ * @rx_nbits: number of bits used for reading. If 0 the default
+ *      (SPI_NBITS_SINGLE) is used.
  * @len: size of rx and tx buffers (in bytes)
  * @speed_hz: Select a speed other than the device default for this
  *      transfer. If 0 the default (from @spi_device) is used.
@@ -508,6 +521,11 @@ extern struct spi_master *spi_busnum_to_master(u16 busnum);
  * by the results of previous messages and where the whole transaction
  * ends when the chipselect goes intactive.
  *
+ * When SPI can transfer in 1x,2x or 4x. It can get this tranfer information
+ * from device through @tx_nbits and @rx_nbits. In Bi-direction, these
+ * two should both be set. User can set transfer mode with SPI_NBITS_SINGLE(1x)
+ * SPI_NBITS_DUAL(2x) and SPI_NBITS_QUAD(4x) to support these three transfer.
+ *
  * The code that submits an spi_message (and its spi_transfers)
  * to the lower layers is responsible for managing its memory.
  * Zero-initialize every field you don't set up explicitly, to
@@ -528,6 +546,11 @@ struct spi_transfer {
 	dma_addr_t	rx_dma;
 
 	unsigned	cs_change:1;
+	u8		tx_nbits;
+	u8		rx_nbits;
+#define	SPI_NBITS_SINGLE	0x01 /* 1bit transfer */
+#define	SPI_NBITS_DUAL		0x02 /* 2bits transfer */
+#define	SPI_NBITS_QUAD		0x04 /* 4bits transfer */
 	u8		bits_per_word;
 	u16		delay_usecs;
 	u32		speed_hz;
@@ -876,7 +899,7 @@ struct spi_board_info {
 	/* mode becomes spi_device.mode, and is essential for chips
 	 * where the default of SPI_CS_HIGH = 0 is wrong.
 	 */
-	u8		mode;
+	u16		mode;
 
 	/* ... may need additional spi_device chip config data here.
 	 * avoid stuff protocol drivers can set; but include stuff