Merge branch 'for-rmk/2635' of git://git.fluff.org/bjdooks/linux into devel-stable

arch/arm/Kconfig

@@ -657,7 +657,7 @@ config ARCH_SA1100
 	  Support for StrongARM 11x0 based boards.
 
 config ARCH_S3C2410
-	bool "Samsung S3C2410, S3C2412, S3C2413, S3C2440, S3C2442, S3C2443"
+	bool "Samsung S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443, S3C2450"
 	select GENERIC_GPIO
 	select ARCH_HAS_CPUFREQ
 	select HAVE_CLK
@@ -666,6 +666,10 @@ config ARCH_S3C2410
 	  BAST (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or
 	  the Samsung SMDK2410 development board (and derivatives).
 
+	  Note, the S3C2416 and the S3C2450 are so close that they even share
+	  the same SoC ID code. This means that there is no seperate machine
+	  directory (no arch/arm/mach-s3c2450) as the S3C2416 was first.
+
 config ARCH_S3C64XX
 	bool "Samsung S3C64XX"
 	select PLAT_SAMSUNG
@@ -904,6 +908,7 @@ if ARCH_S3C2410
 source "arch/arm/mach-s3c2400/Kconfig"
 source "arch/arm/mach-s3c2410/Kconfig"
 source "arch/arm/mach-s3c2412/Kconfig"
+source "arch/arm/mach-s3c2416/Kconfig"
 source "arch/arm/mach-s3c2440/Kconfig"
 source "arch/arm/mach-s3c2443/Kconfig"
 endif

arch/arm/Makefile

@@ -161,7 +161,7 @@ machine-$(CONFIG_ARCH_PNX4008)		:= pnx4008
 machine-$(CONFIG_ARCH_PXA)		:= pxa
 machine-$(CONFIG_ARCH_REALVIEW)		:= realview
 machine-$(CONFIG_ARCH_RPC)		:= rpc
-machine-$(CONFIG_ARCH_S3C2410)		:= s3c2410 s3c2400 s3c2412 s3c2440 s3c2443
+machine-$(CONFIG_ARCH_S3C2410)		:= s3c2410 s3c2400 s3c2412 s3c2416 s3c2440 s3c2443
 machine-$(CONFIG_ARCH_S3C24A0)		:= s3c24a0
 machine-$(CONFIG_ARCH_S3C64XX)		:= s3c64xx
 machine-$(CONFIG_ARCH_S5P6440)		:= s5p6440

arch/arm/mach-s3c2410/Kconfig

@@ -6,6 +6,7 @@ config CPU_S3C2410
 	bool
 	depends on ARCH_S3C2410
 	select CPU_ARM920T
+	select S3C_GPIO_PULL_UP
 	select S3C2410_CLOCK
 	select S3C2410_GPIO
 	select CPU_LLSERIAL_S3C2410

arch/arm/mach-s3c2410/h1940-bluetooth.c

@@ -33,14 +33,15 @@ static void h1940bt_enable(int on)
 		h1940_latch_control(0, H1940_LATCH_BLUETOOTH_POWER);
 		/* Reset the chip */
 		mdelay(10);
-		s3c2410_gpio_setpin(S3C2410_GPH(1), 1);
+
+		gpio_set_value(S3C2410_GPH(1), 1);
 		mdelay(10);
-		s3c2410_gpio_setpin(S3C2410_GPH(1), 0);
+		gpio_set_value(S3C2410_GPH(1), 0);
 	}
 	else {
-		s3c2410_gpio_setpin(S3C2410_GPH(1), 1);
+		gpio_set_value(S3C2410_GPH(1), 1);
 		mdelay(10);
-		s3c2410_gpio_setpin(S3C2410_GPH(1), 0);
+		gpio_set_value(S3C2410_GPH(1), 0);
 		mdelay(10);
 		h1940_latch_control(H1940_LATCH_BLUETOOTH_POWER, 0);
 	}
@@ -61,15 +62,21 @@ static int __devinit h1940bt_probe(struct platform_device *pdev)
 	struct rfkill *rfk;
 	int ret = 0;
 
+	ret = gpio_request(S3C2410_GPH(1), dev_name(&pdev->dev));
+	if (ret) {
+		dev_err(&pdev->dev, "could not get GPH1\n");\
+		return ret;
+	}
+
 	/* Configures BT serial port GPIOs */
-	s3c2410_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0);
-	s3c2410_gpio_pullup(S3C2410_GPH(0), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT);
-	s3c2410_gpio_pullup(S3C2410_GPH(1), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0);
-	s3c2410_gpio_pullup(S3C2410_GPH(2), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0);
-	s3c2410_gpio_pullup(S3C2410_GPH(3), 1);
+	s3c_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0);
+	s3c_gpio_cfgpull(S3C2410_GPH(0), S3C_GPIO_PULL_NONE);
+	s3c_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpull(S3C2410_GPH(1), S3C_GPIO_PULL_NONE);
+	s3c_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0);
+	s3c_gpio_cfgpull(S3C2410_GPH(2), S3C_GPIO_PULL_NONE);
+	s3c_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0);
+	s3c_gpio_cfgpull(S3C2410_GPH(3), S3C_GPIO_PULL_NONE);
 
 
 	rfk = rfkill_alloc(DRV_NAME, &pdev->dev, RFKILL_TYPE_BLUETOOTH,
@@ -100,6 +107,7 @@ static int h1940bt_remove(struct platform_device *pdev)
 	struct rfkill *rfk = platform_get_drvdata(pdev);
 
 	platform_set_drvdata(pdev, NULL);
+	gpio_free(S3C2410_GPH(1));
 
 	if (rfk) {
 		rfkill_unregister(rfk);

arch/arm/mach-s3c2410/include/mach/dma.h

@@ -54,7 +54,7 @@ enum dma_ch {
 #define DMACH_LOW_LEVEL	(1<<28)	/* use this to specifiy hardware ch no */
 
 /* we have 4 dma channels */
-#ifndef CONFIG_CPU_S3C2443
+#if !defined(CONFIG_CPU_S3C2443) && !defined(CONFIG_CPU_S3C2416)
 #define S3C_DMA_CHANNELS		(4)
 #else
 #define S3C_DMA_CHANNELS		(6)

arch/arm/mach-s3c2410/include/mach/gpio-fns.h

@@ -10,14 +10,28 @@
  * published by the Free Software Foundation.
 */
 
+#ifndef __MACH_GPIO_FNS_H
+#define __MACH_GPIO_FNS_H __FILE__
+
 /* These functions are in the to-be-removed category and it is strongly
  * encouraged not to use these in new code. They will be marked deprecated
  * very soon.
  *
  * Most of the functionality can be either replaced by the gpiocfg calls
  * for the s3c platform or by the generic GPIOlib API.
+ *
+ * As of 2.6.35-rc, these will be removed, with the few drivers using them
+ * either replaced or given a wrapper until the calls can be removed.
 */
 
+#include <plat/gpio-cfg.h>
+
+static inline void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int cfg)
+{
+	/* 1:1 mapping between cfgpin and setcfg calls at the moment */
+	s3c_gpio_cfgpin(pin, cfg);
+}
+
 /* external functions for GPIO support
  *
  * These allow various different clients to access the same GPIO
@@ -25,17 +39,6 @@
  * GPIO register, then it is safe to ioremap/__raw_{read|write} to it.
 */
 
-/* s3c2410_gpio_cfgpin
- *
- * set the configuration of the given pin to the value passed.
- *
- * eg:
- *    s3c2410_gpio_cfgpin(S3C2410_GPA(0), S3C2410_GPA0_ADDR0);
- *    s3c2410_gpio_cfgpin(S3C2410_GPE(8), S3C2410_GPE8_SDDAT1);
-*/
-
-extern void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function);
-
 extern unsigned int s3c2410_gpio_getcfg(unsigned int pin);
 
 /* s3c2410_gpio_getirq
@@ -71,6 +74,14 @@ extern int s3c2400_gpio_getirq(unsigned int pin);
 extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
 				  unsigned int config);
 
+/* s3c2410_gpio_pullup
+ *
+ * This call should be replaced with s3c_gpio_setpull().
+ *
+ * As a note, there is currently no distinction between pull-up and pull-down
+ * in the s3c24xx series devices with only an on/off configuration.
+ */
+
 /* s3c2410_gpio_pullup
  *
  * configure the pull-up control on the given pin
@@ -86,18 +97,8 @@ extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
 
 extern void s3c2410_gpio_pullup(unsigned int pin, unsigned int to);
 
-/* s3c2410_gpio_getpull
- *
- * Read the state of the pull-up on a given pin
- *
- * return:
- *	< 0 => error code
- *	  0 => enabled
- *	  1 => disabled
-*/
-
-extern int s3c2410_gpio_getpull(unsigned int pin);
-
 extern void s3c2410_gpio_setpin(unsigned int pin, unsigned int to);
 
 extern unsigned int s3c2410_gpio_getpin(unsigned int pin);
+
+#endif /* __MACH_GPIO_FNS_H */

arch/arm/mach-s3c2410/include/mach/gpio-nrs.h

@@ -34,6 +34,10 @@
 #define S3C2410_GPIO_F_NR	(32)
 #define S3C2410_GPIO_G_NR	(32)
 #define S3C2410_GPIO_H_NR	(32)
+#define S3C2410_GPIO_J_NR	(32)	/* technically 16. */
+#define S3C2410_GPIO_K_NR	(32)	/* technically 16. */
+#define S3C2410_GPIO_L_NR	(32)	/* technically 15. */
+#define S3C2410_GPIO_M_NR	(32)	/* technically 2. */
 
 #if CONFIG_S3C_GPIO_SPACE != 0
 #error CONFIG_S3C_GPIO_SPACE cannot be zero at the moment
@@ -53,6 +57,10 @@ enum s3c_gpio_number {
 	S3C2410_GPIO_F_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_E),
 	S3C2410_GPIO_G_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_F),
 	S3C2410_GPIO_H_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_G),
+	S3C2410_GPIO_J_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_H),
+	S3C2410_GPIO_K_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_J),
+	S3C2410_GPIO_L_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_K),
+	S3C2410_GPIO_M_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_L),
 };
 
 #endif /* __ASSEMBLY__ */
@@ -67,6 +75,10 @@ enum s3c_gpio_number {
 #define S3C2410_GPF(_nr)	(S3C2410_GPIO_F_START + (_nr))
 #define S3C2410_GPG(_nr)	(S3C2410_GPIO_G_START + (_nr))
 #define S3C2410_GPH(_nr)	(S3C2410_GPIO_H_START + (_nr))
+#define S3C2410_GPJ(_nr)	(S3C2410_GPIO_J_START + (_nr))
+#define S3C2410_GPK(_nr)	(S3C2410_GPIO_K_START + (_nr))
+#define S3C2410_GPL(_nr)	(S3C2410_GPIO_L_START + (_nr))
+#define S3C2410_GPM(_nr)	(S3C2410_GPIO_M_START + (_nr))
 
 /* compatibility until drivers can be modified */
 

arch/arm/mach-s3c2410/include/mach/irqs.h

@@ -115,6 +115,26 @@
 #define IRQ_S3C2412_SDI		S3C2410_IRQSUB(13)
 #define IRQ_S3C2412_CF		S3C2410_IRQSUB(14)
 
+
+#define IRQ_S3C2416_EINT8t15	S3C2410_IRQ(5)
+#define IRQ_S3C2416_DMA		S3C2410_IRQ(17)
+#define IRQ_S3C2416_UART3	S3C2410_IRQ(18)
+#define IRQ_S3C2416_SDI1	S3C2410_IRQ(20)
+#define IRQ_S3C2416_SDI0	S3C2410_IRQ(21)
+
+#define IRQ_S3C2416_LCD2	S3C2410_IRQSUB(15)
+#define IRQ_S3C2416_LCD3	S3C2410_IRQSUB(16)
+#define IRQ_S3C2416_LCD4	S3C2410_IRQSUB(17)
+#define IRQ_S3C2416_DMA0	S3C2410_IRQSUB(18)
+#define IRQ_S3C2416_DMA1	S3C2410_IRQSUB(19)
+#define IRQ_S3C2416_DMA2	S3C2410_IRQSUB(20)
+#define IRQ_S3C2416_DMA3	S3C2410_IRQSUB(21)
+#define IRQ_S3C2416_DMA4	S3C2410_IRQSUB(22)
+#define IRQ_S3C2416_DMA5	S3C2410_IRQSUB(23)
+#define IRQ_S32416_WDT		S3C2410_IRQSUB(27)
+#define IRQ_S32416_AC97		S3C2410_IRQSUB(28)
+
+
 /* extra irqs for s3c2440 */
 
 #define IRQ_S3C2440_CAM_C	S3C2410_IRQSUB(11)	/* S3C2443 too */
@@ -130,7 +150,10 @@
 #define IRQ_S3C2443_HSMMC	S3C2410_IRQ(20)		/* IRQ_SDI */
 #define IRQ_S3C2443_NAND	S3C2410_IRQ(24)		/* reserved */
 
+#define IRQ_S3C2416_HSMMC0	S3C2410_IRQ(21)		/* S3C2416/S3C2450 */
+
 #define IRQ_HSMMC0		IRQ_S3C2443_HSMMC
+#define IRQ_HSMMC1		IRQ_S3C2416_HSMMC0
 
 #define IRQ_S3C2443_LCD1	S3C2410_IRQSUB(14)
 #define IRQ_S3C2443_LCD2	S3C2410_IRQSUB(15)
@@ -152,7 +175,7 @@
 #define IRQ_S3C2443_WDT		S3C2410_IRQSUB(27)
 #define IRQ_S3C2443_AC97	S3C2410_IRQSUB(28)
 
-#ifdef CONFIG_CPU_S3C2443
+#if defined(CONFIG_CPU_S3C2443) || defined(CONFIG_CPU_S3C2416)
 #define NR_IRQS (IRQ_S3C2443_AC97+1)
 #else
 #define NR_IRQS (IRQ_S3C2440_AC97+1)

arch/arm/mach-s3c2410/include/mach/map.h

@@ -63,9 +63,9 @@
 #define S3C2440_PA_AC97	   (0x5B000000)
 #define S3C2440_SZ_AC97	   SZ_1M
 
-/* S3C2443 High-speed SD/MMC */
+/* S3C2443/S3C2416 High-speed SD/MMC */
 #define S3C2443_PA_HSMMC   (0x4A800000)
-#define S3C2443_SZ_HSMMC   (256)
+#define S3C2416_PA_HSMMC0  (0x4AC00000)
 
 /* S3C2412 memory and IO controls */
 #define S3C2412_PA_SSMC	(0x4F000000)
@@ -110,6 +110,7 @@
 #define S3C_PA_UART	    S3C24XX_PA_UART
 #define S3C_PA_USBHOST	S3C2410_PA_USBHOST
 #define S3C_PA_HSMMC0	    S3C2443_PA_HSMMC
+#define S3C_PA_HSMMC1	    S3C2416_PA_HSMMC0
 #define S3C_PA_NAND	    S3C24XX_PA_NAND
 
 #endif /* __ASM_ARCH_MAP_H */

arch/arm/mach-s3c2410/include/mach/regs-clock.h

@@ -161,4 +161,6 @@
 
 #endif /* CONFIG_CPU_S3C2412 | CONFIG_CPU_S3C2413 */
 
+#define S3C2416_CLKDIV2		S3C2410_CLKREG(0x28)
+
 #endif /* __ASM_ARM_REGS_CLOCK */

arch/arm/mach-s3c2410/include/mach/regs-dsc.h

@@ -19,6 +19,42 @@
 #define S3C2412_DSC1	   S3C2410_GPIOREG(0xe0)
 #endif
 
+#if defined(CONFIG_CPU_S3C2416)
+#define S3C2416_DSC0	   S3C2410_GPIOREG(0xc0)
+#define S3C2416_DSC1	   S3C2410_GPIOREG(0xc4)
+#define S3C2416_DSC2	   S3C2410_GPIOREG(0xc8)
+#define S3C2416_DSC3	   S3C2410_GPIOREG(0x110)
+
+#define S3C2416_SELECT_DSC0	(0 << 30)
+#define S3C2416_SELECT_DSC1	(1 << 30)
+#define S3C2416_SELECT_DSC2	(2 << 30)
+#define S3C2416_SELECT_DSC3	(3 << 30)
+
+#define S3C2416_DSC_GETSHIFT(x)	(x & 30)
+
+#define S3C2416_DSC0_CF		(S3C2416_SELECT_DSC0 | 28)
+#define	S3C2416_DSC0_CF_5mA	(0 << 28)
+#define	S3C2416_DSC0_CF_10mA	(1 << 28)
+#define	S3C2416_DSC0_CF_15mA	(2 << 28)
+#define	S3C2416_DSC0_CF_21mA	(3 << 28)
+#define	S3C2416_DSC0_CF_MASK	(3 << 28)
+
+#define S3C2416_DSC0_nRBE	(S3C2416_SELECT_DSC0 | 26)
+#define	S3C2416_DSC0_nRBE_5mA	(0 << 26)
+#define	S3C2416_DSC0_nRBE_10mA	(1 << 26)
+#define	S3C2416_DSC0_nRBE_15mA	(2 << 26)
+#define	S3C2416_DSC0_nRBE_21mA	(3 << 26)
+#define	S3C2416_DSC0_nRBE_MASK	(3 << 26)
+
+#define S3C2416_DSC0_nROE	(S3C2416_SELECT_DSC0 | 24)
+#define	S3C2416_DSC0_nROE_5mA	(0 << 24)
+#define	S3C2416_DSC0_nROE_10mA	(1 << 24)
+#define	S3C2416_DSC0_nROE_15mA	(2 << 24)
+#define	S3C2416_DSC0_nROE_21mA	(3 << 24)
+#define	S3C2416_DSC0_nROE_MASK	(3 << 24)
+
+#endif
+
 #if defined(CONFIG_CPU_S3C244X)
 
 #define S3C2440_DSC0	   S3C2410_GPIOREG(0xc4)

arch/arm/mach-s3c2410/include/mach/regs-gpio.h

@@ -610,35 +610,73 @@
 #define S3C2410_GPHUP	   S3C2410_GPIOREG(0x78)
 
 #define S3C2410_GPH0_nCTS0  (0x02 << 0)
+#define S3C2416_GPH0_TXD0  (0x02 << 0)
 
 #define S3C2410_GPH1_nRTS0  (0x02 << 2)
+#define S3C2416_GPH1_RXD0  (0x02 << 2)
 
 #define S3C2410_GPH2_TXD0   (0x02 << 4)
+#define S3C2416_GPH2_TXD1   (0x02 << 4)
 
 #define S3C2410_GPH3_RXD0   (0x02 << 6)
+#define S3C2416_GPH3_RXD1   (0x02 << 6)
 
 #define S3C2410_GPH4_TXD1   (0x02 << 8)
+#define S3C2416_GPH4_TXD2   (0x02 << 8)
 
 #define S3C2410_GPH5_RXD1   (0x02 << 10)
+#define S3C2416_GPH5_RXD2   (0x02 << 10)
 
 #define S3C2410_GPH6_TXD2   (0x02 << 12)
+#define S3C2416_GPH6_TXD3   (0x02 << 12)
 #define S3C2410_GPH6_nRTS1  (0x03 << 12)
+#define S3C2416_GPH6_nRTS2  (0x03 << 12)
 
 #define S3C2410_GPH7_RXD2   (0x02 << 14)
+#define S3C2416_GPH7_RXD3   (0x02 << 14)
 #define S3C2410_GPH7_nCTS1  (0x03 << 14)
+#define S3C2416_GPH7_nCTS2  (0x03 << 14)
 
 #define S3C2410_GPH8_UCLK   (0x02 << 16)
+#define S3C2416_GPH8_nCTS0  (0x02 << 16)
 
 #define S3C2410_GPH9_CLKOUT0  (0x02 << 18)
 #define S3C2442_GPH9_nSPICS0  (0x03 << 18)
+#define S3C2416_GPH9_nRTS0    (0x02 << 18)
 
 #define S3C2410_GPH10_CLKOUT1 (0x02 << 20)
+#define S3C2416_GPH10_nCTS1   (0x02 << 20)
+
+#define S3C2416_GPH11_nRTS1   (0x02 << 22)
+
+#define S3C2416_GPH12_EXTUARTCLK (0x02 << 24)
+
+#define S3C2416_GPH13_CLKOUT0 (0x02 << 26)
+
+#define S3C2416_GPH14_CLKOUT1 (0x02 << 28)
 
 /* The S3C2412 and S3C2413 move the GPJ register set to after
  * GPH, which means all registers after 0x80 are now offset by 0x10
  * for the 2412/2413 from the 2410/2440/2442
 */
 
+/* S3C2443 and above */
+#define S3C2440_GPJCON	   S3C2410_GPIOREG(0xD0)
+#define S3C2440_GPJDAT	   S3C2410_GPIOREG(0xD4)
+#define S3C2440_GPJUP	   S3C2410_GPIOREG(0xD8)
+
+#define S3C2443_GPKCON	   S3C2410_GPIOREG(0xE0)
+#define S3C2443_GPKDAT	   S3C2410_GPIOREG(0xE4)
+#define S3C2443_GPKUP	   S3C2410_GPIOREG(0xE8)
+
+#define S3C2443_GPLCON	   S3C2410_GPIOREG(0xF0)
+#define S3C2443_GPLDAT	   S3C2410_GPIOREG(0xF4)
+#define S3C2443_GPLUP	   S3C2410_GPIOREG(0xF8)
+
+#define S3C2443_GPMCON	   S3C2410_GPIOREG(0x100)
+#define S3C2443_GPMDAT	   S3C2410_GPIOREG(0x104)
+#define S3C2443_GPMUP	   S3C2410_GPIOREG(0x108)
+
 /* miscellaneous control */
 #define S3C2400_MISCCR	   S3C2410_GPIOREG(0x54)
 #define S3C2410_MISCCR	   S3C2410_GPIOREG(0x80)
@@ -686,6 +724,7 @@
 #define S3C2412_MISCCR_CLK1_CLKsrc  (0<<8)
 
 #define S3C2410_MISCCR_USBSUSPND0   (1<<12)
+#define S3C2416_MISCCR_SEL_SUSPND   (1<<12)
 #define S3C2410_MISCCR_USBSUSPND1   (1<<13)
 
 #define S3C2410_MISCCR_nRSTCON	    (1<<16)
@@ -695,6 +734,9 @@
 #define S3C2410_MISCCR_nEN_SCLKE    (1<<19)	/* not 2412 */
 #define S3C2410_MISCCR_SDSLEEP	    (7<<17)
 
+#define S3C2416_MISCCR_FLT_I2C      (1<<24)
+#define S3C2416_MISCCR_HSSPI_EN2    (1<<31)
+
 /* external interrupt control... */
 /* S3C2410_EXTINT0 -> irq sense control for EINT0..EINT7
  * S3C2410_EXTINT1 -> irq sense control for EINT8..EINT15
@@ -762,8 +804,11 @@
 #define S3C2410_GSTATUS1_IDMASK	   (0xffff0000)
 #define S3C2410_GSTATUS1_2410	   (0x32410000)
 #define S3C2410_GSTATUS1_2412	   (0x32412001)
+#define S3C2410_GSTATUS1_2416	   (0x32416003)
 #define S3C2410_GSTATUS1_2440	   (0x32440000)
 #define S3C2410_GSTATUS1_2442	   (0x32440aaa)
+/* some 2416 CPUs report this value also */
+#define S3C2410_GSTATUS1_2450	   (0x32450003)
 
 #define S3C2410_GSTATUS2_WTRESET   (1<<2)
 #define S3C2410_GSTATUS2_OFFRESET  (1<<1)

arch/arm/mach-s3c2410/include/mach/regs-gpioj.h

@@ -22,85 +22,49 @@
  * pull up works like all other ports.
 */
 
-#define S3C2440_GPIO_BANKJ  (416)
-
-#define S3C2440_GPJCON	    S3C2410_GPIOREG(0xd0)
-#define S3C2440_GPJDAT	    S3C2410_GPIOREG(0xd4)
-#define S3C2440_GPJUP	    S3C2410_GPIOREG(0xd8)
-
 #define S3C2413_GPJCON		S3C2410_GPIOREG(0x80)
 #define S3C2413_GPJDAT		S3C2410_GPIOREG(0x84)
 #define S3C2413_GPJUP		S3C2410_GPIOREG(0x88)
 #define S3C2413_GPJSLPCON	S3C2410_GPIOREG(0x8C)
 
-#define S3C2440_GPJ0            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 0)
-#define S3C2440_GPJ0_INP        (0x00 << 0)
 #define S3C2440_GPJ0_OUTP       (0x01 << 0)
 #define S3C2440_GPJ0_CAMDATA0   (0x02 << 0)
 
-#define S3C2440_GPJ1            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 1)
-#define S3C2440_GPJ1_INP        (0x00 << 2)
 #define S3C2440_GPJ1_OUTP       (0x01 << 2)
 #define S3C2440_GPJ1_CAMDATA1   (0x02 << 2)
 
-#define S3C2440_GPJ2            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 2)
-#define S3C2440_GPJ2_INP        (0x00 << 4)
 #define S3C2440_GPJ2_OUTP       (0x01 << 4)
 #define S3C2440_GPJ2_CAMDATA2   (0x02 << 4)
 
-#define S3C2440_GPJ3            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 3)
-#define S3C2440_GPJ3_INP        (0x00 << 6)
 #define S3C2440_GPJ3_OUTP       (0x01 << 6)
 #define S3C2440_GPJ3_CAMDATA3   (0x02 << 6)
 
-#define S3C2440_GPJ4            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 4)
-#define S3C2440_GPJ4_INP        (0x00 << 8)
 #define S3C2440_GPJ4_OUTP       (0x01 << 8)
 #define S3C2440_GPJ4_CAMDATA4   (0x02 << 8)
 
-#define S3C2440_GPJ5            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 5)
-#define S3C2440_GPJ5_INP        (0x00 << 10)
 #define S3C2440_GPJ5_OUTP       (0x01 << 10)
 #define S3C2440_GPJ5_CAMDATA5   (0x02 << 10)
 
-#define S3C2440_GPJ6            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 6)
-#define S3C2440_GPJ6_INP        (0x00 << 12)
 #define S3C2440_GPJ6_OUTP       (0x01 << 12)
 #define S3C2440_GPJ6_CAMDATA6   (0x02 << 12)
 
-#define S3C2440_GPJ7            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 7)
-#define S3C2440_GPJ7_INP        (0x00 << 14)
 #define S3C2440_GPJ7_OUTP       (0x01 << 14)
 #define S3C2440_GPJ7_CAMDATA7   (0x02 << 14)
 
-#define S3C2440_GPJ8            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 8)
-#define S3C2440_GPJ8_INP        (0x00 << 16)
 #define S3C2440_GPJ8_OUTP       (0x01 << 16)
 #define S3C2440_GPJ8_CAMPCLK    (0x02 << 16)
 
-#define S3C2440_GPJ9            S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 9)
-#define S3C2440_GPJ9_INP        (0x00 << 18)
 #define S3C2440_GPJ9_OUTP       (0x01 << 18)
 #define S3C2440_GPJ9_CAMVSYNC   (0x02 << 18)
 
-#define S3C2440_GPJ10           S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 10)
-#define S3C2440_GPJ10_INP       (0x00 << 20)
 #define S3C2440_GPJ10_OUTP      (0x01 << 20)
 #define S3C2440_GPJ10_CAMHREF   (0x02 << 20)
 
-#define S3C2440_GPJ11           S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 11)
-#define S3C2440_GPJ11_INP       (0x00 << 22)
 #define S3C2440_GPJ11_OUTP      (0x01 << 22)
 #define S3C2440_GPJ11_CAMCLKOUT (0x02 << 22)
 
-#define S3C2440_GPJ12           S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 12)
-#define S3C2440_GPJ12_INP       (0x00 << 24)
 #define S3C2440_GPJ12_OUTP      (0x01 << 24)
 #define S3C2440_GPJ12_CAMRESET  (0x02 << 24)
 
-#define S3C2443_GPJ13		S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 13)
-#define S3C2443_GPJ14		S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 14)
-#define S3C2443_GPJ15		S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 15)
-
 #endif	/* __ASM_ARCH_REGS_GPIOJ_H */
 

arch/arm/mach-s3c2410/include/mach/regs-irq.h

@@ -27,6 +27,16 @@
 #define S3C2410_SUBSRCPND      S3C2410_IRQREG(0x018)
 #define S3C2410_INTSUBMSK      S3C2410_IRQREG(0x01C)
 
+#define S3C2416_PRIORITY_MODE1		S3C2410_IRQREG(0x030)
+#define S3C2416_PRIORITY_UPDATE1	S3C2410_IRQREG(0x034)
+#define S3C2416_SRCPND2			S3C2410_IRQREG(0x040)
+#define S3C2416_INTMOD2			S3C2410_IRQREG(0x044)
+#define S3C2416_INTMSK2			S3C2410_IRQREG(0x048)
+#define S3C2416_INTPND2			S3C2410_IRQREG(0x050)
+#define S3C2416_INTOFFSET2		S3C2410_IRQREG(0x054)
+#define S3C2416_PRIORITY_MODE2		S3C2410_IRQREG(0x070)
+#define S3C2416_PRIORITY_UPDATE2	S3C2410_IRQREG(0x074)
+
 /* mask: 0=enable, 1=disable
  * 1 bit EINT, 4=EINT4, 23=EINT23
  * EINT0,1,2,3 are not handled here.

arch/arm/mach-s3c2410/include/mach/regs-s3c2416-mem.h

+/* arch/arm/mach-s3c2410/include/mach/regs-s3c2416-mem.h
+ *
+ * Copyright (c) 2009 Yauhen Kharuzhy <jekhor@gmail.com>,
+ *	as part of OpenInkpot project
+ * Copyright (c) 2009 Promwad Innovation Company
+ *	Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * S3C2416 memory register definitions
+*/
+
+#ifndef __ASM_ARM_REGS_S3C2416_MEM
+#define __ASM_ARM_REGS_S3C2416_MEM
+
+#ifndef S3C2416_MEMREG
+#define S3C2416_MEMREG(x) (S3C24XX_VA_MEMCTRL + (x))
+#endif
+
+#define S3C2416_BANKCFG			S3C2416_MEMREG(0x00)
+#define S3C2416_BANKCON1		S3C2416_MEMREG(0x04)
+#define S3C2416_BANKCON2		S3C2416_MEMREG(0x08)
+#define S3C2416_BANKCON3		S3C2416_MEMREG(0x0C)
+
+#define S3C2416_REFRESH			S3C2416_MEMREG(0x10)
+#define S3C2416_TIMEOUT			S3C2416_MEMREG(0x14)
+
+#endif /*  __ASM_ARM_REGS_S3C2416_MEM */

arch/arm/mach-s3c2410/include/mach/regs-s3c2416.h

+/* arch/arm/mach-s3c2410/include/mach/regs-s3c2416.h
+ *
+ * Copyright (c) 2009 Yauhen Kharuzhy <jekhor@gmail.com>,
+ *	as part of OpenInkpot project
+ * Copyright (c) 2009 Promwad Innovation Company
+ *	Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * S3C2416 specific register definitions
+*/
+
+#ifndef __ASM_ARCH_REGS_S3C2416_H
+#define __ASM_ARCH_REGS_S3C2416_H "s3c2416"
+
+#define S3C2416_SWRST		(S3C24XX_VA_CLKPWR + 0x44)
+#define S3C2416_SWRST_RESET	(0x533C2416)
+
+/* see regs-power.h for the other registers in the power block. */
+
+#endif	/* __ASM_ARCH_REGS_S3C2416_H */
+

arch/arm/mach-s3c2410/include/mach/uncompress.h

@@ -40,7 +40,9 @@ static void arch_detect_cpu(void)
 	cpuid &= S3C2410_GSTATUS1_IDMASK;
 
 	if (is_arm926() || cpuid == S3C2410_GSTATUS1_2440 ||
-	    cpuid == S3C2410_GSTATUS1_2442) {
+	    cpuid == S3C2410_GSTATUS1_2442 ||
+	    cpuid == S3C2410_GSTATUS1_2416 ||
+	    cpuid == S3C2410_GSTATUS1_2450) {
 		fifo_mask = S3C2440_UFSTAT_TXMASK;
 		fifo_max = 63 << S3C2440_UFSTAT_TXSHIFT;
 	} else {

arch/arm/mach-s3c2410/mach-amlm5900.c

@@ -56,6 +56,7 @@
 #include <plat/iic.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
+#include <plat/gpio-cfg.h>
 
 #ifdef CONFIG_MTD_PARTITIONS
 
@@ -225,8 +226,8 @@ static void amlm5900_init_pm(void)
 	} else {
 		enable_irq_wake(IRQ_EINT9);
 		/* configure the suspend/resume status pin */
-		s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT);
-		s3c2410_gpio_pullup(S3C2410_GPF(2), 0);
+		s3c_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT);
+		s3c_gpio_setpull(S3C2410_GPF(2), S3C_GPIO_PULL_UP);
 	}
 }
 static void __init amlm5900_init(void)

arch/arm/mach-s3c2410/mach-bast.c

@@ -61,6 +61,7 @@
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/cpu-freq.h>
+#include <plat/gpio-cfg.h>
 #include <plat/audio-simtec.h>
 
 #include "usb-simtec.h"
@@ -216,15 +217,13 @@ static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = {
 static int bast_pm_suspend(struct sys_device *sd, pm_message_t state)
 {
 	/* ensure that an nRESET is not generated on resume. */
-	s3c2410_gpio_setpin(S3C2410_GPA(21), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT);
-
+	gpio_direction_output(S3C2410_GPA(21), 1);
 	return 0;
 }
 
 static int bast_pm_resume(struct sys_device *sd)
 {
-	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT);
+	s3c_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT);
 	return 0;
 }
 
@@ -658,6 +657,8 @@ static void __init bast_init(void)
 	nor_simtec_init();
 	simtec_audio_add(NULL, true, &bast_audio);
 
+	WARN_ON(gpio_request(S3C2410_GPA(21), "bast nreset"));
+	
 	s3c_cpufreq_setboard(&bast_cpufreq);
 }
 

arch/arm/mach-s3c2410/mach-h1940.c

@@ -50,6 +50,7 @@
 #include <plat/udc.h>
 #include <plat/iic.h>
 
+#include <plat/gpio-cfg.h>
 #include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
@@ -207,16 +208,16 @@ static int h1940_backlight_init(struct device *dev)
 {
 	gpio_request(S3C2410_GPB(0), "Backlight");
 
-	s3c2410_gpio_setpin(S3C2410_GPB(0), 0);
-	s3c2410_gpio_pullup(S3C2410_GPB(0), 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPB0_TOUT0);
+	gpio_direction_output(S3C2410_GPB(0), 0);
+	s3c_gpio_setpull(S3C2410_GPB(0), S3C_GPIO_PULL_NONE);
+	s3c_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPB0_TOUT0);
 
 	return 0;
 }
 
 static void h1940_backlight_exit(struct device *dev)
 {
-	s3c2410_gpio_cfgpin(S3C2410_GPB(0), 1/*S3C2410_GPB0_OUTP*/);
+	gpio_direction_output(S3C2410_GPB(0), 1);
 }
 
 static struct platform_pwm_backlight_data backlight_data = {
@@ -245,18 +246,18 @@ static void h1940_lcd_power_set(struct plat_lcd_data *pd,
 
 	if (!power) {
 		/* set to 3ec */
-		s3c2410_gpio_setpin(S3C2410_GPC(0), 0);
+		gpio_direction_output(S3C2410_GPC(0), 0);
 		/* wait for 3ac */
 		do {
-			value = s3c2410_gpio_getpin(S3C2410_GPC(6));
+			value = gpio_get_value(S3C2410_GPC(6));
 		} while (value);
 		/* set to 38c */
-		s3c2410_gpio_setpin(S3C2410_GPC(5), 0);
+		gpio_direction_output(S3C2410_GPC(5), 0);
 	} else {
 		/* Set to 3ac */
-		s3c2410_gpio_setpin(S3C2410_GPC(5), 1);
+		gpio_direction_output(S3C2410_GPC(5), 1);
 		/* Set to 3ad */
-		s3c2410_gpio_setpin(S3C2410_GPC(0), 1);
+		gpio_direction_output(S3C2410_GPC(0), 1);
 	}
 }
 
@@ -332,6 +333,7 @@ static void __init h1940_init(void)
 	gpio_request(S3C2410_GPC(5), "LCD power");
 	gpio_request(S3C2410_GPC(6), "LCD power");
 
+	gpio_direction_input(S3C2410_GPC(6));
 
 	platform_add_devices(h1940_devices, ARRAY_SIZE(h1940_devices));
 }

arch/arm/mach-s3c2410/mach-n30.c

@@ -86,10 +86,10 @@ static void n30_udc_pullup(enum s3c2410_udc_cmd_e cmd)
 {
 	switch (cmd) {
 	case S3C2410_UDC_P_ENABLE :
-		s3c2410_gpio_setpin(S3C2410_GPB(3), 1);
+		gpio_set_value(S3C2410_GPB(3), 1);
 		break;
 	case S3C2410_UDC_P_DISABLE :
-		s3c2410_gpio_setpin(S3C2410_GPB(3), 0);
+		gpio_set_value(S3C2410_GPB(3), 0);
 		break;
 	case S3C2410_UDC_P_RESET :
 		break;
@@ -536,6 +536,9 @@ static void __init n30_init(void)
 
 		platform_add_devices(n35_devices, ARRAY_SIZE(n35_devices));
 	}
+
+	WARN_ON(gpio_request(S3C2410_GPB(3), "udc pup"));
+	gpio_direction_output(S3C2410_GPB(3), 0);
 }
 
 MACHINE_START(N30, "Acer-N30")

arch/arm/mach-s3c2410/mach-qt2410.c

@@ -58,6 +58,7 @@
 #include <plat/iic.h>
 
 #include <plat/common-smdk.h>
+#include <plat/gpio-cfg.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/pm.h>
@@ -219,10 +220,10 @@ static void spi_gpio_cs(struct s3c2410_spigpio_info *spi, int cs)
 {
 	switch (cs) {
 	case BITBANG_CS_ACTIVE:
-		s3c2410_gpio_setpin(S3C2410_GPB(5), 0);
+		gpio_set_value(S3C2410_GPB(5), 0);
 		break;
 	case BITBANG_CS_INACTIVE:
-		s3c2410_gpio_setpin(S3C2410_GPB(5), 1);
+		gpio_set_value(S3C2410_GPB(5), 1);
 		break;
 	}
 }
@@ -347,13 +348,14 @@ static void __init qt2410_machine_init(void)
 	}
 	s3c24xx_fb_set_platdata(&qt2410_fb_info);
 
-	s3c2410_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPIO_OUTPUT);
 	s3c2410_gpio_setpin(S3C2410_GPB(0), 1);
 
 	s3c24xx_udc_set_platdata(&qt2410_udc_cfg);
 	s3c_i2c0_set_platdata(NULL);
 
-	s3c2410_gpio_cfgpin(S3C2410_GPB(5), S3C2410_GPIO_OUTPUT);
+	WARN_ON(gpio_request(S3C2410_GPB(5), "spi cs"));
+	gpio_direction_output(S3C2410_GPB(5), 1);
 
 	platform_add_devices(qt2410_devices, ARRAY_SIZE(qt2410_devices));
 	s3c_pm_init();

arch/arm/mach-s3c2410/mach-vr1000.c

@@ -357,8 +357,7 @@ static struct clk *vr1000_clocks[] __initdata = {
 
 static void vr1000_power_off(void)
 {
-	s3c2410_gpio_cfgpin(S3C2410_GPB(9), S3C2410_GPIO_OUTPUT);
-	s3c2410_gpio_setpin(S3C2410_GPB(9), 1);
+	gpio_direction_output(S3C2410_GPB(9), 1);
 }
 
 static void __init vr1000_map_io(void)
@@ -395,6 +394,8 @@ static void __init vr1000_init(void)
 
 	nor_simtec_init();
 	simtec_audio_add(NULL, true, NULL);
+
+	WARN_ON(gpio_request(S3C2410_GPB(9), "power off"));
 }
 
 MACHINE_START(VR1000, "Thorcom-VR1000")

arch/arm/mach-s3c2410/s3c2410.c

@@ -16,6 +16,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/clk.h>
 #include <linux/sysdev.h>
 #include <linux/serial_core.h>
@@ -40,6 +41,10 @@
 #include <plat/clock.h>
 #include <plat/pll.h>
 
+#include <plat/gpio-core.h>
+#include <plat/gpio-cfg.h>
+#include <plat/gpio-cfg-helpers.h>
+
 /* Initial IO mappings */
 
 static struct map_desc s3c2410_iodesc[] __initdata = {
@@ -65,6 +70,9 @@ void __init s3c2410_init_uarts(struct s3c2410_uartcfg *cfg, int no)
 
 void __init s3c2410_map_io(void)
 {
+	s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_1up;
+	s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_1up;
+
 	iotable_init(s3c2410_iodesc, ARRAY_SIZE(s3c2410_iodesc));
 }
 

arch/arm/mach-s3c2412/Kconfig

@@ -16,7 +16,8 @@ config CPU_S3C2412
 config CPU_S3C2412_ONLY
 	bool
 	depends on ARCH_S3C2410 && !CPU_S3C2400 && !CPU_S3C2410 && \
-		   !CPU_S3C2440 && !CPU_S3C2442 && !CPU_S3C2443 && CPU_S3C2412
+		   !CPU_2416 && !CPU_S3C2440 && !CPU_S3C2442 && \
+		   !CPU_S3C2443 && CPU_S3C2412
 	default y if CPU_S3C2412
 
 config S3C2412_DMA

arch/arm/mach-s3c2412/mach-jive.c

@@ -48,6 +48,7 @@
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/partitions.h>
 
+#include <plat/gpio-cfg.h>
 #include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
@@ -357,8 +358,7 @@ static void jive_lcm_reset(unsigned int set)
 {
 	printk(KERN_DEBUG "%s(%d)\n", __func__, set);
 
-	s3c2410_gpio_setpin(S3C2410_GPG(13), set);
-	s3c2410_gpio_cfgpin(S3C2410_GPG(13), S3C2410_GPIO_OUTPUT);
+	gpio_set_value(S3C2410_GPG(13), set);
 }
 
 #undef LCD_UPPER_MARGIN
@@ -391,7 +391,7 @@ static struct ili9320_platdata jive_lcm_config = {
 
 static void jive_lcd_spi_chipselect(struct s3c2410_spigpio_info *spi, int cs)
 {
-	s3c2410_gpio_setpin(S3C2410_GPB(7), cs ? 0 : 1);
+	gpio_set_value(S3C2410_GPB(7), cs ? 0 : 1);
 }
 
 static struct s3c2410_spigpio_info jive_lcd_spi = {
@@ -413,7 +413,7 @@ static struct platform_device jive_device_lcdspi = {
 
 static void jive_wm8750_chipselect(struct s3c2410_spigpio_info *spi, int cs)
 {
-	s3c2410_gpio_setpin(S3C2410_GPH(10), cs ? 0 : 1);
+	gpio_set_value(S3C2410_GPH(10), cs ? 0 : 1);
 }
 
 static struct s3c2410_spigpio_info jive_wm8750_spi = {
@@ -531,7 +531,7 @@ static void jive_power_off(void)
 	printk(KERN_INFO "powering system down...\n");
 
 	s3c2410_gpio_setpin(S3C2410_GPC(5), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
 }
 
 static void __init jive_machine_init(void)
@@ -636,22 +636,22 @@ static void __init jive_machine_init(void)
 
 	/* initialise the spi */
 
-	s3c2410_gpio_setpin(S3C2410_GPG(13), 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPG(13), S3C2410_GPIO_OUTPUT);
+	gpio_request(S3C2410_GPG(13), "lcm reset");
+	gpio_direction_output(S3C2410_GPG(13), 0);
 
-	s3c2410_gpio_setpin(S3C2410_GPB(7), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPB(7), S3C2410_GPIO_OUTPUT);
+	gpio_request(S3C2410_GPB(7), "jive spi");
+	gpio_direction_output(S3C2410_GPB(7), 1);
 
 	s3c2410_gpio_setpin(S3C2410_GPB(6), 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPB(6), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPB(6), S3C2410_GPIO_OUTPUT);
 
 	s3c2410_gpio_setpin(S3C2410_GPG(8), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPG(8), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPG(8), S3C2410_GPIO_OUTPUT);
 
 	/* initialise the WM8750 spi */
 
-	s3c2410_gpio_setpin(S3C2410_GPH(10), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPH(10), S3C2410_GPIO_OUTPUT);
+	gpio_request(S3C2410_GPH(10), "jive wm8750 spi");
+	gpio_direction_output(S3C2410_GPH(10), 1);
 
 	/* Turn off suspend on both USB ports, and switch the
 	 * selectable USB port to USB device mode. */

arch/arm/mach-s3c2412/mach-smdk2413.c

@@ -85,10 +85,10 @@ static void smdk2413_udc_pullup(enum s3c2410_udc_cmd_e cmd)
 	switch (cmd)
 	{
 		case S3C2410_UDC_P_ENABLE :
-			s3c2410_gpio_setpin(S3C2410_GPF(2), 1);
+			gpio_set_value(S3C2410_GPF(2), 1);
 			break;
 		case S3C2410_UDC_P_DISABLE :
-			s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
+			gpio_set_value(S3C2410_GPF(2), 0);
 			break;
 		case S3C2410_UDC_P_RESET :
 			break;
@@ -134,8 +134,8 @@ static void __init smdk2413_machine_init(void)
 {	/* Turn off suspend on both USB ports, and switch the
 	 * selectable USB port to USB device mode. */
 
-	s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT);
+	WARN_ON(gpio_request(S3C2410_GPF(2), "udc pull"));
+	gpio_direction_output(S3C2410_GPF(2), 0);
 
 	s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST |
 			      S3C2410_MISCCR_USBSUSPND0 |

arch/arm/mach-s3c2416/Kconfig

+# arch/arm/mach-s3c2416/Kconfig
+#
+# Copyright 2009 Yauhen Kharuzhy <jekhor@gmail.com>
+#
+# Licensed under GPLv2
+
+# note, this also supports the S3C2450 which is so similar it has the same
+# ID code as the S3C2416.
+
+config CPU_S3C2416
+	bool
+	depends on ARCH_S3C2410
+	select CPU_ARM926T
+	select S3C2416_DMA if S3C2410_DMA
+	select CPU_LLSERIAL_S3C2440
+	select S3C_GPIO_PULL_UPDOWN
+	select SAMSUNG_CLKSRC
+	select S3C2443_CLOCK
+	help
+	  Support for the S3C2416 SoC from the S3C24XX line
+
+config S3C2416_DMA
+	bool
+	depends on CPU_S3C2416
+	help
+	  Internal config node for S3C2416 DMA support
+
+menu "S3C2416 Machines"
+
+config MACH_SMDK2416
+	bool "SMDK2416"
+	select CPU_S3C2416
+	select S3C_DEV_HSMMC
+	select S3C_DEV_HSMMC1
+	help
+	  Say Y here if you are using an SMDK2416
+
+endmenu

arch/arm/mach-s3c2416/Makefile

+# arch/arm/mach-s3c2416/Makefile
+#
+# Copyright 2009 Yauhen Kharuzhy <jekhor@gmail.com>
+#
+# Licensed under GPLv2
+
+obj-y				:=
+obj-m				:=
+obj-n				:=
+obj-				:=
+
+obj-$(CONFIG_CPU_S3C2416)	+= s3c2416.o clock.o
+obj-$(CONFIG_CPU_S3C2416)	+= irq.o
+
+#obj-$(CONFIG_S3C2416_DMA)	+= dma.o
+
+# Machine support
+
+obj-$(CONFIG_MACH_SMDK2416)	+= mach-smdk2416.o

arch/arm/mach-s3c2416/clock.c

+/* linux/arch/arm/mach-s3c2416/clock.c
+ *
+ * Copyright (c) 2010 Simtec Electronics
+ * Copyright (c) 2010 Ben Dooks <ben-linux@fluff.org>
+ *
+ * S3C2416 Clock control support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/clk.h>
+
+#include <plat/s3c2416.h>
+#include <plat/s3c2443.h>
+#include <plat/clock.h>
+#include <plat/clock-clksrc.h>
+#include <plat/cpu.h>
+
+#include <plat/cpu-freq.h>
+#include <plat/pll6553x.h>
+#include <plat/pll.h>
+
+#include <asm/mach/map.h>
+
+#include <mach/regs-clock.h>
+#include <mach/regs-s3c2443-clock.h>
+
+static unsigned int armdiv[8] = {
+	[0] = 1,
+	[1] = 2,
+	[2] = 3,
+	[3] = 4,
+	[5] = 6,
+	[7] = 8,
+};
+
+/* ID to hardware numbering, 0 is HSMMC1, 1 is HSMMC0 */
+static struct clksrc_clk hsmmc_div[] = {
+	[0] = {
+		.clk = {
+			.name	= "hsmmc-div",
+			.id	= 1,
+			.parent	= &clk_esysclk.clk,
+		},
+		.reg_div = { .reg = S3C2416_CLKDIV2, .size = 2, .shift = 6 },
+	},
+	[1] = {
+		.clk = {
+			.name	= "hsmmc-div",
+			.id	= 0,
+			.parent	= &clk_esysclk.clk,
+		},
+		.reg_div = { .reg = S3C2443_CLKDIV1, .size = 2, .shift = 6 },
+	},
+};
+
+static struct clksrc_clk hsmmc_mux[] = {
+	[0] = {
+		.clk	= {
+			.id	= 1,
+			.name	= "hsmmc-if",
+			.ctrlbit = (1 << 6),
+			.enable = s3c2443_clkcon_enable_s,
+		},
+		.sources = &(struct clksrc_sources) {
+			.nr_sources = 2,
+			.sources = (struct clk *[]) {
+				[0] = &hsmmc_div[0].clk,
+				[1] = NULL, /* to fix */
+			},
+		},
+		.reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 16 },
+	},
+	[1] = {
+		.clk	= {
+			.id	= 0,
+			.name	= "hsmmc-if",
+			.ctrlbit = (1 << 12),
+			.enable = s3c2443_clkcon_enable_s,
+		},
+		.sources = &(struct clksrc_sources) {
+			.nr_sources = 2,
+			.sources = (struct clk *[]) {
+				[0] = &hsmmc_div[1].clk,
+				[1] = NULL, /* to fix */
+			},
+		},
+		.reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 17 },
+	},
+};
+
+
+static inline unsigned int s3c2416_fclk_div(unsigned long clkcon0)
+{
+	clkcon0 &= 7 << S3C2443_CLKDIV0_ARMDIV_SHIFT;
+
+	return armdiv[clkcon0 >> S3C2443_CLKDIV0_ARMDIV_SHIFT];
+}
+
+void __init_or_cpufreq s3c2416_setup_clocks(void)
+{
+	s3c2443_common_setup_clocks(s3c2416_get_pll, s3c2416_fclk_div);
+}
+
+
+static struct clksrc_clk *clksrcs[] __initdata = {
+	&hsmmc_div[0],
+	&hsmmc_div[1],
+	&hsmmc_mux[0],
+	&hsmmc_mux[1],
+};
+
+void __init s3c2416_init_clocks(int xtal)
+{
+	u32 epllcon = __raw_readl(S3C2443_EPLLCON);
+	u32 epllcon1 = __raw_readl(S3C2443_EPLLCON+4);
+	int ptr;
+
+	/* s3c2416 EPLL compatible with s3c64xx */
+	clk_epll.rate = s3c_get_pll6553x(xtal, epllcon, epllcon1);
+
+	clk_epll.parent = &clk_epllref.clk;
+
+	s3c2443_common_init_clocks(xtal, s3c2416_get_pll, s3c2416_fclk_div);
+
+	for (ptr = 0; ptr < ARRAY_SIZE(clksrcs); ptr++)
+		s3c_register_clksrc(clksrcs[ptr], 1);
+
+	s3c_pwmclk_init();
+
+}

arch/arm/mach-s3c2416/irq.c

+/* linux/arch/arm/mach-s3c2416/irq.c
+ *
+ * Copyright (c) 2009 Yauhen Kharuzhy <jekhor@gmail.com>,
+ *	as part of OpenInkpot project
+ * Copyright (c) 2009 Promwad Innovation Company
+ *	Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+*/
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/sysdev.h>
+#include <linux/io.h>
+
+#include <mach/hardware.h>
+#include <asm/irq.h>
+
+#include <asm/mach/irq.h>
+
+#include <mach/regs-irq.h>
+#include <mach/regs-gpio.h>
+
+#include <plat/cpu.h>
+#include <plat/pm.h>
+#include <plat/irq.h>
+
+#define INTMSK(start, end) ((1 << ((end) + 1 - (start))) - 1)
+
+static inline void s3c2416_irq_demux(unsigned int irq, unsigned int len)
+{
+	unsigned int subsrc, submsk;
+	unsigned int end;
+
+	/* read the current pending interrupts, and the mask
+	 * for what it is available */
+
+	subsrc = __raw_readl(S3C2410_SUBSRCPND);
+	submsk = __raw_readl(S3C2410_INTSUBMSK);
+
+	subsrc  &= ~submsk;
+	subsrc >>= (irq - S3C2410_IRQSUB(0));
+	subsrc  &= (1 << len)-1;
+
+	end = len + irq;
+
+	for (; irq < end && subsrc; irq++) {
+		if (subsrc & 1)
+			generic_handle_irq(irq);
+
+		subsrc >>= 1;
+	}
+}
+
+/* WDT/AC97 sub interrupts */
+
+static void s3c2416_irq_demux_wdtac97(unsigned int irq, struct irq_desc *desc)
+{
+	s3c2416_irq_demux(IRQ_S3C2443_WDT, 4);
+}
+
+#define INTMSK_WDTAC97	(1UL << (IRQ_WDT - IRQ_EINT0))
+#define SUBMSK_WDTAC97	INTMSK(IRQ_S3C2443_WDT, IRQ_S3C2443_AC97)
+
+static void s3c2416_irq_wdtac97_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_WDTAC97, SUBMSK_WDTAC97);
+}
+
+static void s3c2416_irq_wdtac97_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_WDTAC97);
+}
+
+static void s3c2416_irq_wdtac97_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_WDTAC97, SUBMSK_WDTAC97);
+}
+
+static struct irq_chip s3c2416_irq_wdtac97 = {
+	.mask	    = s3c2416_irq_wdtac97_mask,
+	.unmask	    = s3c2416_irq_wdtac97_unmask,
+	.ack	    = s3c2416_irq_wdtac97_ack,
+};
+
+
+/* LCD sub interrupts */
+
+static void s3c2416_irq_demux_lcd(unsigned int irq, struct irq_desc *desc)
+{
+	s3c2416_irq_demux(IRQ_S3C2443_LCD1, 4);
+}
+
+#define INTMSK_LCD	(1UL << (IRQ_LCD - IRQ_EINT0))
+#define SUBMSK_LCD	INTMSK(IRQ_S3C2443_LCD1, IRQ_S3C2443_LCD4)
+
+static void s3c2416_irq_lcd_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_LCD, SUBMSK_LCD);
+}
+
+static void s3c2416_irq_lcd_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_LCD);
+}
+
+static void s3c2416_irq_lcd_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_LCD, SUBMSK_LCD);
+}
+
+static struct irq_chip s3c2416_irq_lcd = {
+	.mask	    = s3c2416_irq_lcd_mask,
+	.unmask	    = s3c2416_irq_lcd_unmask,
+	.ack	    = s3c2416_irq_lcd_ack,
+};
+
+
+/* DMA sub interrupts */
+
+static void s3c2416_irq_demux_dma(unsigned int irq, struct irq_desc *desc)
+{
+	s3c2416_irq_demux(IRQ_S3C2443_DMA0, 6);
+}
+
+#define INTMSK_DMA	(1UL << (IRQ_S3C2443_DMA - IRQ_EINT0))
+#define SUBMSK_DMA	INTMSK(IRQ_S3C2443_DMA0, IRQ_S3C2443_DMA5)
+
+
+static void s3c2416_irq_dma_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_DMA, SUBMSK_DMA);
+}
+
+static void s3c2416_irq_dma_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_DMA);
+}
+
+static void s3c2416_irq_dma_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_DMA, SUBMSK_DMA);
+}
+
+static struct irq_chip s3c2416_irq_dma = {
+	.mask	    = s3c2416_irq_dma_mask,
+	.unmask	    = s3c2416_irq_dma_unmask,
+	.ack	    = s3c2416_irq_dma_ack,
+};
+
+
+/* UART3 sub interrupts */
+
+static void s3c2416_irq_demux_uart3(unsigned int irq, struct irq_desc *desc)
+{
+	s3c2416_irq_demux(IRQ_S3C2443_UART3, 3);
+}
+
+#define INTMSK_UART3	(1UL << (IRQ_S3C2443_UART3 - IRQ_EINT0))
+#define SUBMSK_UART3	(0xf << (IRQ_S3C2443_RX3 - S3C2410_IRQSUB(0)))
+
+
+static void s3c2416_irq_uart3_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_UART3, SUBMSK_UART3);
+}
+
+static void s3c2416_irq_uart3_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_UART3);
+}
+
+static void s3c2416_irq_uart3_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_UART3, SUBMSK_UART3);
+}
+
+static struct irq_chip s3c2416_irq_uart3 = {
+	.mask	    = s3c2416_irq_uart3_mask,
+	.unmask	    = s3c2416_irq_uart3_unmask,
+	.ack	    = s3c2416_irq_uart3_ack,
+};
+
+
+/* IRQ initialisation code */
+
+static int __init s3c2416_add_sub(unsigned int base,
+				   void (*demux)(unsigned int,
+						 struct irq_desc *),
+				   struct irq_chip *chip,
+				   unsigned int start, unsigned int end)
+{
+	unsigned int irqno;
+
+	set_irq_chip(base, &s3c_irq_level_chip);
+	set_irq_handler(base, handle_level_irq);
+	set_irq_chained_handler(base, demux);
+
+	for (irqno = start; irqno <= end; irqno++) {
+		set_irq_chip(irqno, chip);
+		set_irq_handler(irqno, handle_level_irq);
+		set_irq_flags(irqno, IRQF_VALID);
+	}
+
+	return 0;
+}
+
+static int __init s3c2416_irq_add(struct sys_device *sysdev)
+{
+	printk(KERN_INFO "S3C2416: IRQ Support\n");
+
+	s3c2416_add_sub(IRQ_LCD, s3c2416_irq_demux_lcd, &s3c2416_irq_lcd,
+			IRQ_S3C2443_LCD2, IRQ_S3C2443_LCD4);
+
+	s3c2416_add_sub(IRQ_S3C2443_DMA, s3c2416_irq_demux_dma,
+			&s3c2416_irq_dma, IRQ_S3C2443_DMA0, IRQ_S3C2443_DMA5);
+
+	s3c2416_add_sub(IRQ_S3C2443_UART3, s3c2416_irq_demux_uart3,
+			&s3c2416_irq_uart3,
+			IRQ_S3C2443_RX3, IRQ_S3C2443_ERR3);
+
+	s3c2416_add_sub(IRQ_WDT, s3c2416_irq_demux_wdtac97,
+			&s3c2416_irq_wdtac97,
+			IRQ_S3C2443_WDT, IRQ_S3C2443_AC97);
+
+	return 0;
+}
+
+static struct sysdev_driver s3c2416_irq_driver = {
+	.add		= s3c2416_irq_add,
+};
+
+static int __init s3c2416_irq_init(void)
+{
+	return sysdev_driver_register(&s3c2416_sysclass, &s3c2416_irq_driver);
+}
+
+arch_initcall(s3c2416_irq_init);
+

arch/arm/mach-s3c2416/mach-smdk2416.c

+/* linux/arch/arm/mach-s3c2416/mach-hanlin_v3c.c
+ *
+ * Copyright (c) 2009 Yauhen Kharuzhy <jekhor@gmail.com>,
+ *	as part of OpenInkpot project
+ * Copyright (c) 2009 Promwad Innovation Company
+ *	Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/mtd/partitions.h>
+#include <linux/gpio.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-lcd.h>
+
+#include <mach/idle.h>
+#include <mach/fb.h>
+#include <mach/leds-gpio.h>
+#include <plat/iic.h>
+
+#include <plat/s3c2416.h>
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+#include <plat/nand.h>
+
+#include <plat/common-smdk.h>
+
+static struct map_desc smdk2416_iodesc[] __initdata = {
+	/* ISA IO Space map (memory space selected by A24) */
+
+	{
+		.virtual	= (u32)S3C24XX_VA_ISA_WORD,
+		.pfn		= __phys_to_pfn(S3C2410_CS2),
+		.length		= 0x10000,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= (u32)S3C24XX_VA_ISA_WORD + 0x10000,
+		.pfn		= __phys_to_pfn(S3C2410_CS2 + (1<<24)),
+		.length		= SZ_4M,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= (u32)S3C24XX_VA_ISA_BYTE,
+		.pfn		= __phys_to_pfn(S3C2410_CS2),
+		.length		= 0x10000,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= (u32)S3C24XX_VA_ISA_BYTE + 0x10000,
+		.pfn		= __phys_to_pfn(S3C2410_CS2 + (1<<24)),
+		.length		= SZ_4M,
+		.type		= MT_DEVICE,
+	}
+};
+
+#define UCON (S3C2410_UCON_DEFAULT	| \
+		S3C2440_UCON_PCLK	| \
+		S3C2443_UCON_RXERR_IRQEN)
+
+#define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE)
+
+#define UFCON (S3C2410_UFCON_RXTRIG8	| \
+		S3C2410_UFCON_FIFOMODE	| \
+		S3C2440_UFCON_TXTRIG16)
+
+static struct s3c2410_uartcfg smdk2416_uartcfgs[] __initdata = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	/* IR port */
+	[2] = {
+		.hwport	     = 2,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON | 0x50,
+		.ufcon	     = UFCON,
+	}
+};
+
+static struct platform_device *smdk2416_devices[] __initdata = {
+	&s3c_device_wdt,
+	&s3c_device_ohci,
+	&s3c_device_i2c0,
+	&s3c_device_hsmmc0,
+	&s3c_device_hsmmc1,
+};
+
+static void __init smdk2416_map_io(void)
+{
+
+	s3c24xx_init_io(smdk2416_iodesc, ARRAY_SIZE(smdk2416_iodesc));
+	s3c24xx_init_clocks(12000000);
+	s3c24xx_init_uarts(smdk2416_uartcfgs, ARRAY_SIZE(smdk2416_uartcfgs));
+
+}
+
+static void __init smdk2416_machine_init(void)
+{
+	s3c_i2c0_set_platdata(NULL);
+
+	gpio_request(S3C2410_GPB(4), "USBHost Power");
+	gpio_direction_output(S3C2410_GPB(4), 1);
+
+	platform_add_devices(smdk2416_devices, ARRAY_SIZE(smdk2416_devices));
+	smdk_machine_init();
+}
+
+MACHINE_START(SMDK2416, "SMDK2416")
+	/* Maintainer: Yauhen Kharuzhy <jekhor@gmail.com> */
+	.phys_io	= S3C2410_PA_UART,
+	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+
+	.init_irq	= s3c24xx_init_irq,
+	.map_io		= smdk2416_map_io,
+	.init_machine	= smdk2416_machine_init,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

arch/arm/mach-s3c2416/s3c2416.c

+/* linux/arch/arm/mach-s3c2416/s3c2416.c
+ *
+ * Copyright (c) 2009 Yauhen Kharuzhy <jekhor@gmail.com>,
+ *	as part of OpenInkpot project
+ * Copyright (c) 2009 Promwad Innovation Company
+ *	Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
+ *
+ * Samsung S3C2416 Mobile CPU support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/serial_core.h>
+#include <linux/sysdev.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <asm/proc-fns.h>
+#include <asm/irq.h>
+
+#include <mach/reset.h>
+#include <mach/idle.h>
+#include <mach/regs-s3c2443-clock.h>
+
+#include <plat/gpio-core.h>
+#include <plat/gpio-cfg.h>
+#include <plat/gpio-cfg-helpers.h>
+#include <plat/s3c2416.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+
+#include <plat/iic-core.h>
+
+static struct map_desc s3c2416_iodesc[] __initdata = {
+	IODESC_ENT(WATCHDOG),
+	IODESC_ENT(CLKPWR),
+	IODESC_ENT(TIMER),
+};
+
+struct sysdev_class s3c2416_sysclass = {
+	.name = "s3c2416-core",
+};
+
+static struct sys_device s3c2416_sysdev = {
+	.cls		= &s3c2416_sysclass,
+};
+
+static void s3c2416_hard_reset(void)
+{
+	__raw_writel(S3C2443_SWRST_RESET, S3C2443_SWRST);
+}
+
+int __init s3c2416_init(void)
+{
+	printk(KERN_INFO "S3C2416: Initializing architecture\n");
+
+	s3c24xx_reset_hook = s3c2416_hard_reset;
+	/* s3c24xx_idle = s3c2416_idle;	*/
+
+	/* change WDT IRQ number */
+	s3c_device_wdt.resource[1].start = IRQ_S3C2443_WDT;
+	s3c_device_wdt.resource[1].end   = IRQ_S3C2443_WDT;
+
+	/* the i2c devices are directly compatible with s3c2440 */
+	s3c_i2c0_setname("s3c2440-i2c");
+	s3c_i2c1_setname("s3c2440-i2c");
+
+	return sysdev_register(&s3c2416_sysdev);
+}
+
+void __init s3c2416_init_uarts(struct s3c2410_uartcfg *cfg, int no)
+{
+	s3c24xx_init_uartdevs("s3c2440-uart", s3c2410_uart_resources, cfg, no);
+
+	s3c_device_nand.name = "s3c2416-nand";
+}
+
+/* s3c2416_map_io
+ *
+ * register the standard cpu IO areas, and any passed in from the
+ * machine specific initialisation.
+ */
+
+void __init s3c2416_map_io(void)
+{
+	s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_updown;
+	s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_updown;
+
+	iotable_init(s3c2416_iodesc, ARRAY_SIZE(s3c2416_iodesc));
+}
+
+/* need to register class before we actually register the device, and
+ * we also need to ensure that it has been initialised before any of the
+ * drivers even try to use it (even if not on an s3c2416 based system)
+ * as a driver which may support both 2443 and 2440 may try and use it.
+*/
+
+static int __init s3c2416_core_init(void)
+{
+	return sysdev_class_register(&s3c2416_sysclass);
+}
+
+core_initcall(s3c2416_core_init);

arch/arm/mach-s3c2440/Kconfig

@@ -6,6 +6,7 @@ config CPU_S3C2440
 	bool
 	depends on ARCH_S3C2410
 	select CPU_ARM920T
+	select S3C_GPIO_PULL_UP
 	select S3C2410_CLOCK
 	select S3C2410_PM if PM
 	select S3C2410_GPIO

arch/arm/mach-s3c2440/mach-mini2440.c

@@ -53,6 +53,7 @@
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/partitions.h>
 
+#include <plat/gpio-cfg.h>
 #include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
@@ -102,10 +103,10 @@ static void mini2440_udc_pullup(enum s3c2410_udc_cmd_e cmd)
 
 	switch (cmd) {
 		case S3C2410_UDC_P_ENABLE :
-			s3c2410_gpio_setpin(S3C2410_GPC(5), 1);
+			gpio_set_value(S3C2410_GPC(5), 1);
 			break;
 		case S3C2410_UDC_P_DISABLE :
-			s3c2410_gpio_setpin(S3C2410_GPC(5), 0);
+			gpio_set_value(S3C2410_GPC(5), 0);
 			break;
 		case S3C2410_UDC_P_RESET :
 			break;
@@ -632,25 +633,25 @@ static void __init mini2440_init(void)
 	mini2440_parse_features(&features, mini2440_features_str);
 
 	/* turn LCD on */
-	s3c2410_gpio_cfgpin(S3C2410_GPC(0), S3C2410_GPC0_LEND);
+	s3c_gpio_cfgpin(S3C2410_GPC(0), S3C2410_GPC0_LEND);
 
 	/* Turn the backlight early on */
-	s3c2410_gpio_setpin(S3C2410_GPG(4), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPG(4), S3C2410_GPIO_OUTPUT);
+	WARN_ON(gpio_request(S3C2410_GPG(4), "backlight"));
+	gpio_direction_output(S3C2410_GPG(4), 1);
 
 	/* remove pullup on optional PWM backlight -- unused on 3.5 and 7"s */
-	s3c2410_gpio_pullup(S3C2410_GPB(1), 0);
+	s3c_gpio_setpull(S3C2410_GPB(1), S3C_GPIO_PULL_UP);
 	s3c2410_gpio_setpin(S3C2410_GPB(1), 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPB(1), S3C2410_GPIO_INPUT);
+	s3c_gpio_cfgpin(S3C2410_GPB(1), S3C2410_GPIO_INPUT);
 
 	/* Make sure the D+ pullup pin is output */
-	s3c2410_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
+	WARN_ON(gpio_request(S3C2410_GPC(5), "udc pup"));
+	gpio_direction_output(S3C2410_GPC(5), 0);
 
 	/* mark the key as input, without pullups (there is one on the board) */
 	for (i = 0; i < ARRAY_SIZE(mini2440_buttons); i++) {
-		s3c2410_gpio_pullup(mini2440_buttons[i].gpio, 0);
-		s3c2410_gpio_cfgpin(mini2440_buttons[i].gpio,
-					S3C2410_GPIO_INPUT);
+		s3c_gpio_setpull(mini2440_buttons[i].gpio, S3C_GPIO_PULL_UP);
+		s3c_gpio_cfgpin(mini2440_buttons[i].gpio, S3C2410_GPIO_INPUT);
 	}
 	if (features.lcd_index != -1) {
 		int li;

arch/arm/mach-s3c2440/mach-nexcoder.c

@@ -40,6 +40,7 @@
 #include <plat/regs-serial.h>
 #include <plat/iic.h>
 
+#include <plat/gpio-cfg.h>
 #include <plat/s3c2410.h>
 #include <plat/s3c244x.h>
 #include <plat/clock.h>
@@ -122,15 +123,15 @@ static void __init nexcoder_sensorboard_init(void)
 {
 	// Initialize SCCB bus
 	s3c2410_gpio_setpin(S3C2410_GPE(14), 1); // IICSCL
-	s3c2410_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPIO_OUTPUT);
 	s3c2410_gpio_setpin(S3C2410_GPE(15), 1); // IICSDA
-	s3c2410_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPIO_OUTPUT);
 
 	// Power up the sensor board
 	s3c2410_gpio_setpin(S3C2410_GPF(1), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPF(1), S3C2410_GPIO_OUTPUT); // CAM_GPIO7 => nLDO_PWRDN
+	s3c_gpio_cfgpin(S3C2410_GPF(1), S3C2410_GPIO_OUTPUT); // CAM_GPIO7 => nLDO_PWRDN
 	s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
-	s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); // CAM_GPIO6 => CAM_PWRDN
+	s3c_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); // CAM_GPIO6 => CAM_PWRDN
 }
 
 static void __init nexcoder_map_io(void)

arch/arm/mach-s3c2440/mach-osiris.c

@@ -49,6 +49,7 @@
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/partitions.h>
 
+#include <plat/gpio-cfg.h>
 #include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
@@ -298,7 +299,7 @@ static int osiris_pm_suspend(struct sys_device *sd, pm_message_t state)
 
 	/* ensure that an nRESET is not generated on resume. */
 	s3c2410_gpio_setpin(S3C2410_GPA(21), 1);
-	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT);
 
 	return 0;
 }
@@ -310,7 +311,7 @@ static int osiris_pm_resume(struct sys_device *sd)
 
 	__raw_writeb(pm_osiris_ctrl0, OSIRIS_VA_CTRL0);
 
-	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT);
+	s3c_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT);
 
 	return 0;
 }

arch/arm/mach-s3c2440/s3c2440.c

@@ -19,6 +19,7 @@
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
 #include <linux/sysdev.h>
+#include <linux/gpio.h>
 #include <linux/clk.h>
 #include <linux/io.h>
 
@@ -33,6 +34,10 @@
 #include <plat/cpu.h>
 #include <plat/s3c244x.h>
 
+#include <plat/gpio-core.h>
+#include <plat/gpio-cfg.h>
+#include <plat/gpio-cfg-helpers.h>
+
 static struct sys_device s3c2440_sysdev = {
 	.cls		= &s3c2440_sysclass,
 };
@@ -41,6 +46,9 @@ int __init s3c2440_init(void)
 {
 	printk("S3C2440: Initialising architecture\n");
 
+	s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_1up;
+	s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_1up;
+
 	/* change irq for watchdog */
 
 	s3c_device_wdt.resource[1].start = IRQ_S3C2440_WDT;

arch/arm/mach-s3c2443/Kconfig

@@ -8,6 +8,7 @@ config CPU_S3C2443
 	select S3C2443_DMA if S3C2410_DMA
 	select CPU_LLSERIAL_S3C2440
 	select SAMSUNG_CLKSRC
+	select S3C2443_CLOCK
 	help
 	  Support for the S3C2443 SoC from the S3C24XX line
 

arch/arm/mach-s3c2443/clock.c

@@ -21,6 +21,7 @@
 */
 
 #include <linux/init.h>
+
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/list.h>
@@ -54,111 +55,13 @@
  * set the correct muxing at initialisation
 */
 
-static int s3c2443_gate(void __iomem *reg, struct clk *clk, int enable)
-{
-	u32 ctrlbit = clk->ctrlbit;
-	u32 con = __raw_readl(reg);
-
-	if (enable)
-		con |= ctrlbit;
-	else
-		con &= ~ctrlbit;
-
-	__raw_writel(con, reg);
-	return 0;
-}
-
-static int s3c2443_clkcon_enable_h(struct clk *clk, int enable)
-{
-	return s3c2443_gate(S3C2443_HCLKCON, clk, enable);
-}
-
-static int s3c2443_clkcon_enable_p(struct clk *clk, int enable)
-{
-	return s3c2443_gate(S3C2443_PCLKCON, clk, enable);
-}
-
-static int s3c2443_clkcon_enable_s(struct clk *clk, int enable)
-{
-	return s3c2443_gate(S3C2443_SCLKCON, clk, enable);
-}
-
 /* clock selections */
 
-/* mpllref is a direct descendant of clk_xtal by default, but it is not
- * elided as the EPLL can be either sourced by the XTAL or EXTCLK and as
- * such directly equating the two source clocks is impossible.
- */
-static struct clk clk_mpllref = {
-	.name		= "mpllref",
-	.parent		= &clk_xtal,
-	.id		= -1,
-};
-
 static struct clk clk_i2s_ext = {
 	.name		= "i2s-ext",
 	.id		= -1,
 };
 
-static struct clk *clk_epllref_sources[] = {
-	[0] = &clk_mpllref,
-	[1] = &clk_mpllref,
-	[2] = &clk_xtal,
-	[3] = &clk_ext,
-};
-
-static struct clksrc_clk clk_epllref = {
-	.clk	= {
-		.name		= "epllref",
-		.id		= -1,
-	},
-	.sources = &(struct clksrc_sources) {
-		.sources = clk_epllref_sources,
-		.nr_sources = ARRAY_SIZE(clk_epllref_sources),
-	},
-	.reg_src = { .reg = S3C2443_CLKSRC, .size = 2, .shift = 7 },
-};
-
-static unsigned long s3c2443_getrate_mdivclk(struct clk *clk)
-{
-	unsigned long parent_rate = clk_get_rate(clk->parent);
-	unsigned long div = __raw_readl(S3C2443_CLKDIV0);
-
-	div  &= S3C2443_CLKDIV0_EXTDIV_MASK;
-	div >>= (S3C2443_CLKDIV0_EXTDIV_SHIFT-1);	/* x2 */
-
-	return parent_rate / (div + 1);
-}
-
-static struct clk clk_mdivclk = {
-	.name		= "mdivclk",
-	.parent		= &clk_mpllref,
-	.id		= -1,
-	.ops		= &(struct clk_ops) {
-		.get_rate	= s3c2443_getrate_mdivclk,
-	},
-};
-
-static struct clk *clk_msysclk_sources[] = {
-	[0] = &clk_mpllref,
-	[1] = &clk_mpll,
-	[2] = &clk_mdivclk,
-	[3] = &clk_mpllref,
-};
-
-static struct clksrc_clk clk_msysclk = {
-	.clk	= {
-		.name		= "msysclk",
-		.parent		= &clk_xtal,
-		.id		= -1,
-	},
-	.sources = &(struct clksrc_sources) {
-		.sources = clk_msysclk_sources,
-		.nr_sources = ARRAY_SIZE(clk_msysclk_sources),
-	},
-	.reg_src = { .reg = S3C2443_CLKSRC, .size = 2, .shift = 3 },
-};
-
 /* armdiv
  *
  * this clock is sourced from msysclk and can have a number of
@@ -266,44 +169,6 @@ static struct clksrc_clk clk_arm = {
 	.reg_src = { .reg = S3C2443_CLKDIV0, .size = 1, .shift = 13 },
 };
 
-/* esysclk
- *
- * this is sourced from either the EPLL or the EPLLref clock
-*/
-
-static struct clk *clk_sysclk_sources[] = {
-	[0] = &clk_epllref.clk,
-	[1] = &clk_epll,
-};
-
-static struct clksrc_clk clk_esysclk = {
-	.clk	= {
-		.name		= "esysclk",
-		.parent		= &clk_epll,
-		.id		= -1,
-	},
-	.sources = &(struct clksrc_sources) {
-		.sources = clk_sysclk_sources,
-		.nr_sources = ARRAY_SIZE(clk_sysclk_sources),
-	},
-	.reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 6 },
-};
-
-/* uartclk
- *
- * UART baud-rate clock sourced from esysclk via a divisor
-*/
-
-static struct clksrc_clk clk_uart = {
-	.clk	= {
-		.name		= "uartclk",
-		.id		= -1,
-		.parent		= &clk_esysclk.clk,
-	},
-	.reg_div = { .reg = S3C2443_CLKDIV1, .size = 4, .shift = 8 },
-};
-
-
 /* hsspi
  *
  * high-speed spi clock, sourced from esysclk
@@ -320,21 +185,6 @@ static struct clksrc_clk clk_hsspi = {
 	.reg_div = { .reg = S3C2443_CLKDIV1, .size = 2, .shift = 4 },
 };
 
-/* usbhost
- *
- * usb host bus-clock, usually 48MHz to provide USB bus clock timing
-*/
-
-static struct clksrc_clk clk_usb_bus_host = {
-	.clk	= {
-		.name		= "usb-bus-host-parent",
-		.id		= -1,
-		.parent		= &clk_esysclk.clk,
-		.ctrlbit	= S3C2443_SCLKCON_USBHOST,
-		.enable		= s3c2443_clkcon_enable_s,
-	},
-	.reg_div = { .reg = S3C2443_CLKDIV1, .size = 2, .shift = 4 },
-};
 
 /* clk_hsmcc_div
  *
@@ -433,88 +283,15 @@ static struct clksrc_clk clk_i2s = {
 	.reg_src = { .reg = S3C2443_CLKSRC, .size = 2, .shift = 14 },
 };
 
-/* cam-if
- *
- * camera interface bus-clock, divided down from esysclk
-*/
-
-static struct clksrc_clk clk_cam = {
-	.clk	= {
-		.name		= "camif-upll",	/* same as 2440 name */
-		.id		= -1,
-		.parent		= &clk_esysclk.clk,
-		.ctrlbit	= S3C2443_SCLKCON_CAMCLK,
-		.enable		= s3c2443_clkcon_enable_s,
-	},
-	.reg_div = { .reg = S3C2443_CLKDIV1, .size = 4, .shift = 26 },
-};
-
-/* display-if
- *
- * display interface clock, divided from esysclk
-*/
-
-static struct clksrc_clk clk_display = {
-	.clk	= {
-		.name		= "display-if",
-		.id		= -1,
-		.parent		= &clk_esysclk.clk,
-		.ctrlbit	= S3C2443_SCLKCON_DISPCLK,
-		.enable		= s3c2443_clkcon_enable_s,
-	},
-	.reg_div = { .reg = S3C2443_CLKDIV1, .size = 8, .shift = 16 },
-};
-
-/* prediv
- *
- * this divides the msysclk down to pass to h/p/etc.
- */
-
-static unsigned long s3c2443_prediv_getrate(struct clk *clk)
-{
-	unsigned long rate = clk_get_rate(clk->parent);
-	unsigned long clkdiv0 = __raw_readl(S3C2443_CLKDIV0);
-
-	clkdiv0 &= S3C2443_CLKDIV0_PREDIV_MASK;
-	clkdiv0 >>= S3C2443_CLKDIV0_PREDIV_SHIFT;
-
-	return rate / (clkdiv0 + 1);
-}
-
-static struct clk clk_prediv = {
-	.name		= "prediv",
-	.id		= -1,
-	.parent		= &clk_msysclk.clk,
-	.ops		= &(struct clk_ops) {
-		.get_rate	= s3c2443_prediv_getrate,
-	},
-};
-
 /* standard clock definitions */
 
-static struct clk init_clocks_disable[] = {
+static struct clk init_clocks_off[] = {
 	{
-		.name		= "nand",
-		.id		= -1,
-		.parent		= &clk_h,
-	}, {
 		.name		= "sdi",
 		.id		= -1,
 		.parent		= &clk_p,
 		.enable		= s3c2443_clkcon_enable_p,
 		.ctrlbit	= S3C2443_PCLKCON_SDI,
-	}, {
-		.name		= "adc",
-		.id		= -1,
-		.parent		= &clk_p,
-		.enable		= s3c2443_clkcon_enable_p,
-		.ctrlbit	= S3C2443_PCLKCON_ADC,
-	}, {
-		.name		= "i2c",
-		.id		= -1,
-		.parent		= &clk_p,
-		.enable		= s3c2443_clkcon_enable_p,
-		.ctrlbit	= S3C2443_PCLKCON_IIC,
 	}, {
 		.name		= "iis",
 		.id		= -1,
@@ -537,179 +314,12 @@ static struct clk init_clocks_disable[] = {
 };
 
 static struct clk init_clocks[] = {
-	{
-		.name		= "dma",
-		.id		= 0,
-		.parent		= &clk_h,
-		.enable		= s3c2443_clkcon_enable_h,
-		.ctrlbit	= S3C2443_HCLKCON_DMA0,
-	}, {
-		.name		= "dma",
-		.id		= 1,
-		.parent		= &clk_h,
-		.enable		= s3c2443_clkcon_enable_h,
-		.ctrlbit	= S3C2443_HCLKCON_DMA1,
-	}, {
-		.name		= "dma",
-		.id		= 2,
-		.parent		= &clk_h,
-		.enable		= s3c2443_clkcon_enable_h,
-		.ctrlbit	= S3C2443_HCLKCON_DMA2,
-	}, {
-		.name		= "dma",
-		.id		= 3,
-		.parent		= &clk_h,
-		.enable		= s3c2443_clkcon_enable_h,
-		.ctrlbit	= S3C2443_HCLKCON_DMA3,
-	}, {
-		.name		= "dma",
-		.id		= 4,
-		.parent		= &clk_h,
-		.enable		= s3c2443_clkcon_enable_h,
-		.ctrlbit	= S3C2443_HCLKCON_DMA4,
-	}, {
-		.name		= "dma",
-		.id		= 5,
-		.parent		= &clk_h,
-		.enable		= s3c2443_clkcon_enable_h,
-		.ctrlbit	= S3C2443_HCLKCON_DMA5,
-	}, {
-		.name		= "lcd",
-		.id		= -1,
-		.parent		= &clk_h,
-		.enable		= s3c2443_clkcon_enable_h,
-		.ctrlbit	= S3C2443_HCLKCON_LCDC,
-	}, {
-		.name		= "gpio",
-		.id		= -1,
-		.parent		= &clk_p,
-		.enable		= s3c2443_clkcon_enable_p,
-		.ctrlbit	= S3C2443_PCLKCON_GPIO,
-	}, {
-		.name		= "usb-host",
-		.id		= -1,
-		.parent		= &clk_h,
-		.enable		= s3c2443_clkcon_enable_h,
-		.ctrlbit	= S3C2443_HCLKCON_USBH,
-	}, {
-		.name		= "usb-device",
-		.id		= -1,
-		.parent		= &clk_h,
-		.enable		= s3c2443_clkcon_enable_h,
-		.ctrlbit	= S3C2443_HCLKCON_USBD,
-	}, {
-		.name		= "hsmmc",
-		.id		= -1,
-		.parent		= &clk_h,
-		.enable		= s3c2443_clkcon_enable_h,
-		.ctrlbit	= S3C2443_HCLKCON_HSMMC,
-	}, {
-		.name		= "cfc",
-		.id		= -1,
-		.parent		= &clk_h,
-		.enable		= s3c2443_clkcon_enable_h,
-		.ctrlbit	= S3C2443_HCLKCON_CFC,
-	}, {
-		.name		= "ssmc",
-		.id		= -1,
-		.parent		= &clk_h,
-		.enable		= s3c2443_clkcon_enable_h,
-		.ctrlbit	= S3C2443_HCLKCON_SSMC,
-	}, {
-		.name		= "timers",
-		.id		= -1,
-		.parent		= &clk_p,
-		.enable		= s3c2443_clkcon_enable_p,
-		.ctrlbit	= S3C2443_PCLKCON_PWMT,
-	}, {
-		.name		= "uart",
-		.id		= 0,
-		.parent		= &clk_p,
-		.enable		= s3c2443_clkcon_enable_p,
-		.ctrlbit	= S3C2443_PCLKCON_UART0,
-	}, {
-		.name		= "uart",
-		.id		= 1,
-		.parent		= &clk_p,
-		.enable		= s3c2443_clkcon_enable_p,
-		.ctrlbit	= S3C2443_PCLKCON_UART1,
-	}, {
-		.name		= "uart",
-		.id		= 2,
-		.parent		= &clk_p,
-		.enable		= s3c2443_clkcon_enable_p,
-		.ctrlbit	= S3C2443_PCLKCON_UART2,
-	}, {
-		.name		= "uart",
-		.id		= 3,
-		.parent		= &clk_p,
-		.enable		= s3c2443_clkcon_enable_p,
-		.ctrlbit	= S3C2443_PCLKCON_UART3,
-	}, {
-		.name		= "rtc",
-		.id		= -1,
-		.parent		= &clk_p,
-		.enable		= s3c2443_clkcon_enable_p,
-		.ctrlbit	= S3C2443_PCLKCON_RTC,
-	}, {
-		.name		= "watchdog",
-		.id		= -1,
-		.parent		= &clk_p,
-		.ctrlbit	= S3C2443_PCLKCON_WDT,
-	}, {
-		.name		= "usb-bus-host",
-		.id		= -1,
-		.parent		= &clk_usb_bus_host.clk,
-	}, {
-		.name		= "ac97",
-		.id		= -1,
-		.parent		= &clk_p,
-		.ctrlbit	= S3C2443_PCLKCON_AC97,
-	}
-};
-
-/* clocks to add where we need to check their parentage */
-
-static struct clksrc_clk __initdata *init_list[] = {
-	&clk_epllref, /* should be first */
-	&clk_esysclk,
-	&clk_msysclk,
-	&clk_arm,
-	&clk_i2s_eplldiv,
-	&clk_i2s,
-	&clk_cam,
-	&clk_uart,
-	&clk_display,
-	&clk_hsmmc_div,
-	&clk_usb_bus_host,
 };
 
-static void __init s3c2443_clk_initparents(void)
-{
-	int ptr;
-
-	for (ptr = 0; ptr < ARRAY_SIZE(init_list); ptr++)
-		s3c_set_clksrc(init_list[ptr], true);
-}
-
-static inline unsigned long s3c2443_get_hdiv(unsigned long clkcon0)
-{
-	clkcon0 &= S3C2443_CLKDIV0_HCLKDIV_MASK;
-
-	return clkcon0 + 1;
-}
-
 /* clocks to add straight away */
 
 static struct clksrc_clk *clksrcs[] __initdata = {
-	&clk_usb_bus_host,
-	&clk_epllref,
-	&clk_esysclk,
-	&clk_msysclk,
 	&clk_arm,
-	&clk_uart,
-	&clk_display,
-	&clk_cam,
 	&clk_i2s_eplldiv,
 	&clk_i2s,
 	&clk_hsspi,
@@ -717,92 +327,32 @@ static struct clksrc_clk *clksrcs[] __initdata = {
 };
 
 static struct clk *clks[] __initdata = {
-	&clk_ext,
-	&clk_epll,
-	&clk_usb_bus,
-	&clk_mpllref,
 	&clk_hsmmc,
 	&clk_armdiv,
-	&clk_prediv,
 };
 
 void __init_or_cpufreq s3c2443_setup_clocks(void)
 {
-	unsigned long mpllcon = __raw_readl(S3C2443_MPLLCON);
-	unsigned long clkdiv0 = __raw_readl(S3C2443_CLKDIV0);
-	struct clk *xtal_clk;
-	unsigned long xtal;
-	unsigned long pll;
-	unsigned long fclk;
-	unsigned long hclk;
-	unsigned long pclk;
-
-	xtal_clk = clk_get(NULL, "xtal");
-	xtal = clk_get_rate(xtal_clk);
-	clk_put(xtal_clk);
-
-	pll = s3c2443_get_mpll(mpllcon, xtal);
-	clk_msysclk.clk.rate = pll;
-
-	fclk = pll / s3c2443_fclk_div(clkdiv0);
-	hclk = s3c2443_prediv_getrate(&clk_prediv);
-	hclk /= s3c2443_get_hdiv(clkdiv0);
- 	pclk = hclk / ((clkdiv0 & S3C2443_CLKDIV0_HALF_PCLK) ? 2 : 1);
-
-	s3c24xx_setup_clocks(fclk, hclk, pclk);
-
-	printk("S3C2443: mpll %s %ld.%03ld MHz, cpu %ld.%03ld MHz, mem %ld.%03ld MHz, pclk %ld.%03ld MHz\n",
-	       (mpllcon & S3C2443_PLLCON_OFF) ? "off":"on",
-	       print_mhz(pll), print_mhz(fclk),
-	       print_mhz(hclk), print_mhz(pclk));
-
-	s3c24xx_setup_clocks(fclk, hclk, pclk);
+	s3c2443_common_setup_clocks(s3c2443_get_mpll, s3c2443_fclk_div);
 }
 
 void __init s3c2443_init_clocks(int xtal)
 {
-	struct clk *clkp;
 	unsigned long epllcon = __raw_readl(S3C2443_EPLLCON);
-	int ret;
 	int ptr;
 
-	/* s3c2443 parents h and p clocks from prediv */
-	clk_h.parent = &clk_prediv;
-	clk_p.parent = &clk_prediv;
+	clk_epll.rate = s3c2443_get_epll(epllcon, xtal);
+	clk_epll.parent = &clk_epllref.clk;
+
+	s3c2443_common_init_clocks(xtal, s3c2443_get_mpll, s3c2443_fclk_div);
 
-	s3c24xx_register_baseclocks(xtal);
 	s3c2443_setup_clocks();
-	s3c2443_clk_initparents();
-
-	for (ptr = 0; ptr < ARRAY_SIZE(clks); ptr++) {
-		clkp = clks[ptr];
 
-		ret = s3c24xx_register_clock(clkp);
-		if (ret < 0) {
-			printk(KERN_ERR "Failed to register clock %s (%d)\n",
-			       clkp->name, ret);
-		}
-	}
+	s3c24xx_register_clocks(clks, ARRAY_SIZE(clks));
 
 	for (ptr = 0; ptr < ARRAY_SIZE(clksrcs); ptr++)
 		s3c_register_clksrc(clksrcs[ptr], 1);
 
-	clk_epll.rate = s3c2443_get_epll(epllcon, xtal);
-	clk_epll.parent = &clk_epllref.clk;
-	clk_usb_bus.parent = &clk_usb_bus_host.clk;
-
-	/* ensure usb bus clock is within correct rate of 48MHz */
-
-	if (clk_get_rate(&clk_usb_bus_host.clk) != (48 * 1000 * 1000)) {
-		printk(KERN_INFO "Warning: USB host bus not at 48MHz\n");
-		clk_set_rate(&clk_usb_bus_host.clk, 48*1000*1000);
-	}
-
-	printk("S3C2443: epll %s %ld.%03ld MHz, usb-bus %ld.%03ld MHz\n",
-	       (epllcon & S3C2443_PLLCON_OFF) ? "off":"on",
-	       print_mhz(clk_get_rate(&clk_epll)),
-	       print_mhz(clk_get_rate(&clk_usb_bus)));
-
 	/* register clocks from clock array */
 
 	s3c_register_clocks(init_clocks, ARRAY_SIZE(init_clocks));
@@ -819,17 +369,8 @@ void __init s3c2443_init_clocks(int xtal)
 
 	/* install (and disable) the clocks we do not need immediately */
 
-	clkp = init_clocks_disable;
-	for (ptr = 0; ptr < ARRAY_SIZE(init_clocks_disable); ptr++, clkp++) {
-
-		ret = s3c24xx_register_clock(clkp);
-		if (ret < 0) {
-			printk(KERN_ERR "Failed to register clock %s (%d)\n",
-			       clkp->name, ret);
-		}
-
-		(clkp->enable)(clkp, 0);
-	}
+	s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+	s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
 
 	s3c_pwmclk_init();
 }

arch/arm/mach-s3c64xx/gpiolib.c

@@ -51,6 +51,7 @@
 
 static struct s3c_gpio_cfg gpio_4bit_cfg_noint = {
 	.set_config	= s3c_gpio_setcfg_s3c64xx_4bit,
+	.get_config	= s3c_gpio_getcfg_s3c64xx_4bit,
 	.set_pull	= s3c_gpio_setpull_updown,
 	.get_pull	= s3c_gpio_getpull_updown,
 };
@@ -58,12 +59,14 @@ static struct s3c_gpio_cfg gpio_4bit_cfg_noint = {
 static struct s3c_gpio_cfg gpio_4bit_cfg_eint0111 = {
 	.cfg_eint	= 7,
 	.set_config	= s3c_gpio_setcfg_s3c64xx_4bit,
+	.get_config	= s3c_gpio_getcfg_s3c64xx_4bit,
 	.set_pull	= s3c_gpio_setpull_updown,
 	.get_pull	= s3c_gpio_getpull_updown,
 };
 
 static struct s3c_gpio_cfg gpio_4bit_cfg_eint0011 = {
 	.cfg_eint	= 3,
+	.get_config	= s3c_gpio_getcfg_s3c64xx_4bit,
 	.set_config	= s3c_gpio_setcfg_s3c64xx_4bit,
 	.set_pull	= s3c_gpio_setpull_updown,
 	.get_pull	= s3c_gpio_getpull_updown,
@@ -171,6 +174,7 @@ static struct s3c_gpio_chip gpio_4bit2[] = {
 
 static struct s3c_gpio_cfg gpio_2bit_cfg_noint = {
 	.set_config	= s3c_gpio_setcfg_s3c24xx,
+	.get_config	= s3c_gpio_getcfg_s3c24xx,
 	.set_pull	= s3c_gpio_setpull_updown,
 	.get_pull	= s3c_gpio_getpull_updown,
 };
@@ -178,6 +182,7 @@ static struct s3c_gpio_cfg gpio_2bit_cfg_noint = {
 static struct s3c_gpio_cfg gpio_2bit_cfg_eint10 = {
 	.cfg_eint	= 2,
 	.set_config	= s3c_gpio_setcfg_s3c24xx,
+	.get_config	= s3c_gpio_getcfg_s3c24xx,
 	.set_pull	= s3c_gpio_setpull_updown,
 	.get_pull	= s3c_gpio_getpull_updown,
 };
@@ -185,6 +190,7 @@ static struct s3c_gpio_cfg gpio_2bit_cfg_eint10 = {
 static struct s3c_gpio_cfg gpio_2bit_cfg_eint11 = {
 	.cfg_eint	= 3,
 	.set_config	= s3c_gpio_setcfg_s3c24xx,
+	.get_config	= s3c_gpio_getcfg_s3c24xx,
 	.set_pull	= s3c_gpio_setpull_updown,
 	.get_pull	= s3c_gpio_getpull_updown,
 };

arch/arm/mach-s3c64xx/include/mach/pll.h

@@ -20,6 +20,7 @@
 #define S3C6400_PLL_SDIV_SHIFT	(0)
 
 #include <asm/div64.h>
+#include <plat/pll6553x.h>
 
 static inline unsigned long s3c6400_get_pll(unsigned long baseclk,
 					    u32 pllcon)
@@ -37,38 +38,8 @@ static inline unsigned long s3c6400_get_pll(unsigned long baseclk,
 	return (unsigned long)fvco;
 }
 
-#define S3C6400_EPLL_MDIV_MASK	((1 << (23-16)) - 1)
-#define S3C6400_EPLL_PDIV_MASK	((1 << (13-8)) - 1)
-#define S3C6400_EPLL_SDIV_MASK	((1 << (2-0)) - 1)
-#define S3C6400_EPLL_MDIV_SHIFT	(16)
-#define S3C6400_EPLL_PDIV_SHIFT	(8)
-#define S3C6400_EPLL_SDIV_SHIFT	(0)
-#define S3C6400_EPLL_KDIV_MASK  (0xffff)
-
 static inline unsigned long s3c6400_get_epll(unsigned long baseclk)
 {
-	unsigned long result;
-	u32 epll0 = __raw_readl(S3C_EPLL_CON0);
-	u32 epll1 = __raw_readl(S3C_EPLL_CON1);
-	u32 mdiv, pdiv, sdiv, kdiv;
-	u64 tmp;
-
-	mdiv = (epll0 >> S3C6400_EPLL_MDIV_SHIFT) & S3C6400_EPLL_MDIV_MASK;
-	pdiv = (epll0 >> S3C6400_EPLL_PDIV_SHIFT) & S3C6400_EPLL_PDIV_MASK;
-	sdiv = (epll0 >> S3C6400_EPLL_SDIV_SHIFT) & S3C6400_EPLL_SDIV_MASK;
-	kdiv = epll1 & S3C6400_EPLL_KDIV_MASK;
-
-	/* We need to multiple baseclk by mdiv (the integer part) and kdiv
-	 * which is in 2^16ths, so shift mdiv up (does not overflow) and
-	 * add kdiv before multiplying. The use of tmp is to avoid any
-	 * overflows before shifting bac down into result when multipling
-	 * by the mdiv and kdiv pair.
-	 */
-
-	tmp = baseclk;
-	tmp *= (mdiv << 16) + kdiv;
-	do_div(tmp, (pdiv << sdiv));
-	result = tmp >> 16;
-
-	return result;
+	return s3c_get_pll6553x(baseclk, __raw_readl(S3C_EPLL_CON0),
+				__raw_readl(S3C_EPLL_CON1));
 }

arch/arm/mach-s5p6440/gpio.c

@@ -161,12 +161,15 @@ static struct s3c_gpio_cfg s5p6440_gpio_cfgs[] = {
 	}, {
 		.cfg_eint	= 0,
 		.set_config	= s3c_gpio_setcfg_s3c24xx,
+		.get_config	= s3c_gpio_getcfg_s3c24xx,
 	}, {
 		.cfg_eint	= 2,
 		.set_config	= s3c_gpio_setcfg_s3c24xx,
+		.get_config	= s3c_gpio_getcfg_s3c24xx,
 	}, {
 		.cfg_eint	= 3,
 		.set_config	= s3c_gpio_setcfg_s3c24xx,
+		.get_config	= s3c_gpio_getcfg_s3c24xx,
 	},
 };
 
@@ -279,6 +282,8 @@ void __init s5p6440_gpiolib_set_cfg(struct s3c_gpio_cfg *chipcfg, int nr_chips)
 	for (; nr_chips > 0; nr_chips--, chipcfg++) {
 		if (!chipcfg->set_config)
 			chipcfg->set_config	= s3c_gpio_setcfg_s3c64xx_4bit;
+		if (!chipcfg->get_config)
+			chipcfg->get_config	= s3c_gpio_getcfg_s3c64xx_4bit;
 		if (!chipcfg->set_pull)
 			chipcfg->set_pull	= s3c_gpio_setpull_updown;
 		if (!chipcfg->get_pull)

arch/arm/plat-s3c24xx/Kconfig

@@ -9,6 +9,7 @@ config PLAT_S3C24XX
 	select NO_IOPORT
 	select ARCH_REQUIRE_GPIOLIB
 	select S3C_DEVICE_NAND
+	select S3C_GPIO_CFG_S3C24XX
 	help
 	  Base platform code for any Samsung S3C24XX device
 
@@ -44,6 +45,12 @@ config S3C2410_CLOCK
 	  Clock code for the S3C2410, and similar processors which
 	  is currently includes the S3C2410, S3C2440, S3C2442.
 
+config S3C2443_CLOCK
+	bool
+	help
+	  Clock code for the S3C2443 and similar processors, which includes
+	  the S3C2416 and S3C2450.
+
 config S3C24XX_DCLK
 	bool
 	help

arch/arm/plat-s3c24xx/Makefile

@@ -30,6 +30,7 @@ obj-$(CONFIG_PM)		+= pm.o
 obj-$(CONFIG_PM)		+= irq-pm.o
 obj-$(CONFIG_PM)		+= sleep.o
 obj-$(CONFIG_S3C2410_CLOCK)	+= s3c2410-clock.o
+obj-$(CONFIG_S3C2443_CLOCK)	+= s3c2443-clock.o
 obj-$(CONFIG_S3C2410_DMA)	+= dma.o
 obj-$(CONFIG_S3C2410_IOTIMING)	+= s3c2410-iotiming.o
 obj-$(CONFIG_S3C2412_IOTIMING)	+= s3c2412-iotiming.o

arch/arm/plat-s3c24xx/common-smdk.c

@@ -42,6 +42,7 @@
 #include <plat/nand.h>
 
 #include <plat/common-smdk.h>
+#include <plat/gpio-cfg.h>
 #include <plat/devs.h>
 #include <plat/pm.h>
 
@@ -185,10 +186,10 @@ void __init smdk_machine_init(void)
 {
 	/* Configure the LEDs (even if we have no LED support)*/
 
-	s3c2410_gpio_cfgpin(S3C2410_GPF(4), S3C2410_GPIO_OUTPUT);
-	s3c2410_gpio_cfgpin(S3C2410_GPF(5), S3C2410_GPIO_OUTPUT);
-	s3c2410_gpio_cfgpin(S3C2410_GPF(6), S3C2410_GPIO_OUTPUT);
-	s3c2410_gpio_cfgpin(S3C2410_GPF(7), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPF(4), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPF(5), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPF(6), S3C2410_GPIO_OUTPUT);
+	s3c_gpio_cfgpin(S3C2410_GPF(7), S3C2410_GPIO_OUTPUT);
 
 	s3c2410_gpio_setpin(S3C2410_GPF(4), 1);
 	s3c2410_gpio_setpin(S3C2410_GPF(5), 1);

arch/arm/plat-s3c24xx/cpu.c

@@ -49,6 +49,7 @@
 #include <plat/s3c2400.h>
 #include <plat/s3c2410.h>
 #include <plat/s3c2412.h>
+#include <plat/s3c2416.h>
 #include <plat/s3c244x.h>
 #include <plat/s3c2443.h>
 
@@ -57,6 +58,7 @@
 static const char name_s3c2400[]  = "S3C2400";
 static const char name_s3c2410[]  = "S3C2410";
 static const char name_s3c2412[]  = "S3C2412";
+static const char name_s3c2416[]  = "S3C2416/S3C2450";
 static const char name_s3c2440[]  = "S3C2440";
 static const char name_s3c2442[]  = "S3C2442";
 static const char name_s3c2442b[]  = "S3C2442B";
@@ -137,6 +139,15 @@ static struct cpu_table cpu_ids[] __initdata = {
 		.init		= s3c2412_init,
 		.name		= name_s3c2412,
 	},
+	{			/* a strange version of the s3c2416 */
+		.idcode		= 0x32450003,
+		.idmask		= 0xffffffff,
+		.map_io		= s3c2416_map_io,
+		.init_clocks	= s3c2416_init_clocks,
+		.init_uarts	= s3c2416_init_uarts,
+		.init		= s3c2416_init,
+		.name		= name_s3c2416,
+	},
 	{
 		.idcode		= 0x32443001,
 		.idmask		= 0xffffffff,
@@ -170,6 +181,16 @@ static struct map_desc s3c_iodesc[] __initdata = {
 
 static unsigned long s3c24xx_read_idcode_v5(void)
 {
+#if defined(CONFIG_CPU_S3C2416)
+	/* s3c2416 is v5, with S3C24XX_GSTATUS1 instead of S3C2412_GSTATUS1 */
+
+	u32 gs = __raw_readl(S3C24XX_GSTATUS1);
+
+	/* test for s3c2416 or similar device */
+	if ((gs >> 16) == 0x3245)
+		return gs;
+#endif
+
 #if defined(CONFIG_CPU_S3C2412) || defined(CONFIG_CPU_S3C2413)
 	return __raw_readl(S3C2412_GSTATUS1);
 #else

arch/arm/plat-s3c24xx/gpio.c

 /* linux/arch/arm/plat-s3c24xx/gpio.c
  *
- * Copyright (c) 2004-2005 Simtec Electronics
+ * Copyright (c) 2004-2010 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
  *
  * S3C24XX GPIO support
@@ -20,12 +20,12 @@
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 */
 
-
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/interrupt.h>
 #include <linux/ioport.h>
+#include <linux/gpio.h>
 #include <linux/io.h>
 
 #include <mach/hardware.h>
@@ -34,123 +34,34 @@
 
 #include <mach/regs-gpio.h>
 
-void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function)
-{
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long mask;
-	unsigned long con;
-	unsigned long flags;
-
-	if (pin < S3C2410_GPIO_BANKB) {
-		mask = 1 << S3C2410_GPIO_OFFSET(pin);
-	} else {
-		mask = 3 << S3C2410_GPIO_OFFSET(pin)*2;
-	}
-
-	switch (function) {
-	case S3C2410_GPIO_LEAVE:
-		mask = 0;
-		function = 0;
-		break;
-
-	case S3C2410_GPIO_INPUT:
-	case S3C2410_GPIO_OUTPUT:
-	case S3C2410_GPIO_SFN2:
-	case S3C2410_GPIO_SFN3:
-		if (pin < S3C2410_GPIO_BANKB) {
-			function -= 1;
-			function &= 1;
-			function <<= S3C2410_GPIO_OFFSET(pin);
-		} else {
-			function &= 3;
-			function <<= S3C2410_GPIO_OFFSET(pin)*2;
-		}
-	}
-
-	/* modify the specified register wwith IRQs off */
-
-	local_irq_save(flags);
-
-	con  = __raw_readl(base + 0x00);
-	con &= ~mask;
-	con |= function;
-
-	__raw_writel(con, base + 0x00);
-
-	local_irq_restore(flags);
-}
-
-EXPORT_SYMBOL(s3c2410_gpio_cfgpin);
-
-unsigned int s3c2410_gpio_getcfg(unsigned int pin)
-{
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long val = __raw_readl(base);
-
-	if (pin < S3C2410_GPIO_BANKB) {
-		val >>= S3C2410_GPIO_OFFSET(pin);
-		val &= 1;
-		val += 1;
-	} else {
-		val >>= S3C2410_GPIO_OFFSET(pin)*2;
-		val &= 3;
-	}
-
-	return val | S3C2410_GPIO_INPUT;
-}
-
-EXPORT_SYMBOL(s3c2410_gpio_getcfg);
+/* gpiolib wrappers until these are totally eliminated */
 
 void s3c2410_gpio_pullup(unsigned int pin, unsigned int to)
 {
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long offs = S3C2410_GPIO_OFFSET(pin);
-	unsigned long flags;
-	unsigned long up;
+	int ret;
 
-	if (pin < S3C2410_GPIO_BANKB)
-		return;
+	WARN_ON(to);	/* should be none of these left */
 
-	local_irq_save(flags);
-
-	up = __raw_readl(base + 0x08);
-	up &= ~(1L << offs);
-	up |= to << offs;
-	__raw_writel(up, base + 0x08);
+	if (!to) {
+		/* if pull is enabled, try first with up, and if that
+		 * fails, try using down */
 
-	local_irq_restore(flags);
+		ret = s3c_gpio_setpull(pin, S3C_GPIO_PULL_UP);
+		if (ret)
+			s3c_gpio_setpull(pin, S3C_GPIO_PULL_DOWN);
+	} else {
+		s3c_gpio_setpull(pin, S3C_GPIO_PULL_NONE);
+	}
 }
-
 EXPORT_SYMBOL(s3c2410_gpio_pullup);
 
-int s3c2410_gpio_getpull(unsigned int pin)
-{
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long offs = S3C2410_GPIO_OFFSET(pin);
-
-	if (pin < S3C2410_GPIO_BANKB)
-		return -EINVAL;
-
-	return (__raw_readl(base + 0x08) & (1L << offs)) ? 1 : 0;
-}
-
-EXPORT_SYMBOL(s3c2410_gpio_getpull);
-
 void s3c2410_gpio_setpin(unsigned int pin, unsigned int to)
 {
-	void __iomem *base = S3C24XX_GPIO_BASE(pin);
-	unsigned long offs = S3C2410_GPIO_OFFSET(pin);
-	unsigned long flags;
-	unsigned long dat;
-
-	local_irq_save(flags);
+	/* do this via gpiolib until all users removed */
 
-	dat = __raw_readl(base + 0x04);
-	dat &= ~(1 << offs);
-	dat |= to << offs;
-	__raw_writel(dat, base + 0x04);
-
-	local_irq_restore(flags);
+	gpio_request(pin, "temporary");
+	gpio_set_value(pin, to);
+	gpio_free(pin);
 }
 
 EXPORT_SYMBOL(s3c2410_gpio_setpin);
@@ -181,22 +92,3 @@ unsigned int s3c2410_modify_misccr(unsigned int clear, unsigned int change)
 }
 
 EXPORT_SYMBOL(s3c2410_modify_misccr);
-
-int s3c2410_gpio_getirq(unsigned int pin)
-{
-	if (pin < S3C2410_GPF(0) || pin > S3C2410_GPG(15))
-		return -EINVAL;	/* not valid interrupts */
-
-	if (pin < S3C2410_GPG(0) && pin > S3C2410_GPF(7))
-		return -EINVAL;	/* not valid pin */
-
-	if (pin < S3C2410_GPF(4))
-		return (pin - S3C2410_GPF(0)) + IRQ_EINT0;
-
-	if (pin < S3C2410_GPG(0))
-		return (pin - S3C2410_GPF(4)) + IRQ_EINT4;
-
-	return (pin - S3C2410_GPG(0)) + IRQ_EINT8;
-}
-
-EXPORT_SYMBOL(s3c2410_gpio_getirq);

arch/arm/plat-s3c24xx/gpiolib.c

 /* linux/arch/arm/plat-s3c24xx/gpiolib.c
  *
- * Copyright (c) 2008 Simtec Electronics
+ * Copyright (c) 2008-2010 Simtec Electronics
  *	http://armlinux.simtec.co.uk/
  *	Ben Dooks <ben@simtec.co.uk>
  *
@@ -21,6 +21,8 @@
 #include <linux/gpio.h>
 
 #include <plat/gpio-core.h>
+#include <plat/gpio-cfg.h>
+#include <plat/gpio-cfg-helpers.h>
 #include <mach/hardware.h>
 #include <asm/irq.h>
 #include <plat/pm.h>
@@ -77,10 +79,21 @@ static int s3c24xx_gpiolib_bankg_toirq(struct gpio_chip *chip, unsigned offset)
 	return IRQ_EINT8 + offset;
 }
 
+static struct s3c_gpio_cfg s3c24xx_gpiocfg_banka = {
+	.set_config	= s3c_gpio_setcfg_s3c24xx_a,
+	.get_config	= s3c_gpio_getcfg_s3c24xx_a,
+};
+
+struct s3c_gpio_cfg s3c24xx_gpiocfg_default = {
+	.set_config	= s3c_gpio_setcfg_s3c24xx,
+	.get_config	= s3c_gpio_getcfg_s3c24xx,
+};
+
 struct s3c_gpio_chip s3c24xx_gpios[] = {
 	[0] = {
 		.base	= S3C2410_GPACON,
 		.pm	= __gpio_pm(&s3c_gpio_pm_1bit),
+		.config	= &s3c24xx_gpiocfg_banka,
 		.chip	= {
 			.base			= S3C2410_GPA(0),
 			.owner			= THIS_MODULE,
@@ -161,15 +174,58 @@ struct s3c_gpio_chip s3c24xx_gpios[] = {
 			.ngpio			= 11,
 		},
 	},
+		/* GPIOS for the S3C2443 and later devices. */
+	{
+		.base	= S3C2440_GPJCON,
+		.pm	= __gpio_pm(&s3c_gpio_pm_2bit),
+		.chip	= {
+			.base			= S3C2410_GPJ(0),
+			.owner			= THIS_MODULE,
+			.label			= "GPIOJ",
+			.ngpio			= 16,
+		},
+	}, {
+		.base	= S3C2443_GPKCON,
+		.pm	= __gpio_pm(&s3c_gpio_pm_2bit),
+		.chip	= {
+			.base			= S3C2410_GPK(0),
+			.owner			= THIS_MODULE,
+			.label			= "GPIOK",
+			.ngpio			= 16,
+		},
+	}, {
+		.base	= S3C2443_GPLCON,
+		.pm	= __gpio_pm(&s3c_gpio_pm_2bit),
+		.chip	= {
+			.base			= S3C2410_GPL(0),
+			.owner			= THIS_MODULE,
+			.label			= "GPIOL",
+			.ngpio			= 15,
+		},
+	}, {
+		.base	= S3C2443_GPMCON,
+		.pm	= __gpio_pm(&s3c_gpio_pm_2bit),
+		.chip	= {
+			.base			= S3C2410_GPM(0),
+			.owner			= THIS_MODULE,
+			.label			= "GPIOM",
+			.ngpio			= 2,
+		},
+	},
 };
 
+
 static __init int s3c24xx_gpiolib_init(void)
 {
 	struct s3c_gpio_chip *chip = s3c24xx_gpios;
 	int gpn;
 
-	for (gpn = 0; gpn < ARRAY_SIZE(s3c24xx_gpios); gpn++, chip++)
+	for (gpn = 0; gpn < ARRAY_SIZE(s3c24xx_gpios); gpn++, chip++) {
+		if (!chip->config)
+			chip->config = &s3c24xx_gpiocfg_default;
+
 		s3c_gpiolib_add(chip);
+	}
 
 	return 0;
 }

arch/arm/plat-s3c24xx/include/plat/pll.h

@@ -35,3 +35,28 @@ s3c24xx_get_pll(unsigned int pllval, unsigned int baseclk)
 
 	return (unsigned int)fvco;
 }
+
+#define S3C2416_PLL_M_SHIFT	(14)
+#define S3C2416_PLL_P_SHIFT	(5)
+#define S3C2416_PLL_S_MASK	(7)
+#define S3C2416_PLL_M_MASK	((1 << 10) - 1)
+#define S3C2416_PLL_P_MASK	(63)
+
+static inline unsigned int
+s3c2416_get_pll(unsigned int pllval, unsigned int baseclk)
+{
+	unsigned int m, p, s;
+	uint64_t fvco;
+
+	m = pllval >> S3C2416_PLL_M_SHIFT;
+	p = pllval >> S3C2416_PLL_P_SHIFT;
+
+	s = pllval & S3C2416_PLL_S_MASK;
+	m &= S3C2416_PLL_M_MASK;
+	p &= S3C2416_PLL_P_MASK;
+
+	fvco = (uint64_t)baseclk * m;
+	do_div(fvco, (p << s));
+
+	return (unsigned int)fvco;
+}

arch/arm/plat-s3c24xx/include/plat/s3c2416.h

+/* linux/include/asm-arm/plat-s3c24xx/s3c2443.h
+ *
+ * Copyright (c) 2009 Yauhen Kharuzhy <jekhor@gmail.com>
+ *
+ * Header file for s3c2416 cpu support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifdef CONFIG_CPU_S3C2416
+
+struct s3c2410_uartcfg;
+
+extern  int s3c2416_init(void);
+
+extern void s3c2416_map_io(void);
+
+extern void s3c2416_init_uarts(struct s3c2410_uartcfg *cfg, int no);
+
+extern void s3c2416_init_clocks(int xtal);
+
+extern  int s3c2416_baseclk_add(void);
+
+#else
+#define s3c2416_init_clocks NULL
+#define s3c2416_init_uarts NULL
+#define s3c2416_map_io NULL
+#define s3c2416_init NULL
+#endif

arch/arm/plat-s3c24xx/include/plat/s3c2443.h

@@ -30,3 +30,22 @@ extern  int s3c2443_baseclk_add(void);
 #define s3c2443_map_io NULL
 #define s3c2443_init NULL
 #endif
+
+/* common code used by s3c2443 and others.
+ * note, not to be used outside of arch/arm/mach-s3c* */
+
+struct clk;	/* some files don't need clk.h otherwise */
+
+typedef unsigned int (*pll_fn)(unsigned int reg, unsigned int base);
+typedef unsigned int (*fdiv_fn)(unsigned long clkcon0);
+
+extern void s3c2443_common_setup_clocks(pll_fn get_mpll, fdiv_fn fdiv);
+extern void s3c2443_common_init_clocks(int xtal, pll_fn get_mpll, fdiv_fn fdiv);
+
+extern int s3c2443_clkcon_enable_h(struct clk *clk, int enable);
+extern int s3c2443_clkcon_enable_p(struct clk *clk, int enable);
+extern int s3c2443_clkcon_enable_s(struct clk *clk, int enable);
+
+extern struct clksrc_clk clk_epllref;
+extern struct clksrc_clk clk_esysclk;
+extern struct clksrc_clk clk_msysclk;

arch/arm/plat-s3c24xx/pm.c

@@ -43,6 +43,7 @@
 
 #include <asm/mach/time.h>
 
+#include <plat/gpio-cfg.h>
 #include <plat/pm.h>
 
 #define PFX "s3c24xx-pm: "
@@ -90,22 +91,22 @@ static void s3c_pm_check_resume_pin(unsigned int pin, unsigned int irqoffs)
 {
 	unsigned long irqstate;
 	unsigned long pinstate;
-	int irq = s3c2410_gpio_getirq(pin);
+	int irq = gpio_to_irq(pin);
 
 	if (irqoffs < 4)
 		irqstate = s3c_irqwake_intmask & (1L<<irqoffs);
 	else
 		irqstate = s3c_irqwake_eintmask & (1L<<irqoffs);
 
-	pinstate = s3c2410_gpio_getcfg(pin);
+	pinstate = s3c_gpio_getcfg(pin);
 
 	if (!irqstate) {
 		if (pinstate == S3C2410_GPIO_IRQ)
-			S3C_PMDBG("Leaving IRQ %d (pin %d) enabled\n", irq, pin);
+			S3C_PMDBG("Leaving IRQ %d (pin %d) as is\n", irq, pin);
 	} else {
 		if (pinstate == S3C2410_GPIO_IRQ) {
 			S3C_PMDBG("Disabling IRQ %d (pin %d)\n", irq, pin);
-			s3c2410_gpio_cfgpin(pin, S3C2410_GPIO_INPUT);
+			s3c_gpio_cfgpin(pin, S3C2410_GPIO_INPUT);
 		}
 	}
 }

arch/arm/plat-s3c24xx/s3c2410-clock.c

@@ -87,7 +87,7 @@ static int s3c2410_upll_enable(struct clk *clk, int enable)
 
 /* standard clock definitions */
 
-static struct clk init_clocks_disable[] = {
+static struct clk init_clocks_off[] = {
 	{
 		.name		= "nand",
 		.id		= -1,
@@ -249,17 +249,8 @@ int __init s3c2410_baseclk_add(void)
 
 	/* install (and disable) the clocks we do not need immediately */
 
-	clkp = init_clocks_disable;
-	for (ptr = 0; ptr < ARRAY_SIZE(init_clocks_disable); ptr++, clkp++) {
-
-		ret = s3c24xx_register_clock(clkp);
-		if (ret < 0) {
-			printk(KERN_ERR "Failed to register clock %s (%d)\n",
-			       clkp->name, ret);
-		}
-
-		s3c2410_clkcon_enable(clkp, 0);
-	}
+	s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+	s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
 
 	/* show the clock-slow value */
 

arch/arm/plat-s3c24xx/s3c2443-clock.c

+/* linux/arch/arm/plat-s3c24xx/s3c2443-clock.c
+ *
+ * Copyright (c) 2007, 2010 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2443 Clock control suport - common code
+ */
+
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+
+#include <mach/regs-s3c2443-clock.h>
+
+#include <plat/s3c2443.h>
+#include <plat/clock.h>
+#include <plat/clock-clksrc.h>
+#include <plat/cpu.h>
+
+#include <plat/cpu-freq.h>
+
+
+static int s3c2443_gate(void __iomem *reg, struct clk *clk, int enable)
+{
+	u32 ctrlbit = clk->ctrlbit;
+	u32 con = __raw_readl(reg);
+
+	if (enable)
+		con |= ctrlbit;
+	else
+		con &= ~ctrlbit;
+
+	__raw_writel(con, reg);
+	return 0;
+}
+
+int s3c2443_clkcon_enable_h(struct clk *clk, int enable)
+{
+	return s3c2443_gate(S3C2443_HCLKCON, clk, enable);
+}
+
+int s3c2443_clkcon_enable_p(struct clk *clk, int enable)
+{
+	return s3c2443_gate(S3C2443_PCLKCON, clk, enable);
+}
+
+int s3c2443_clkcon_enable_s(struct clk *clk, int enable)
+{
+	return s3c2443_gate(S3C2443_SCLKCON, clk, enable);
+}
+
+/* mpllref is a direct descendant of clk_xtal by default, but it is not
+ * elided as the EPLL can be either sourced by the XTAL or EXTCLK and as
+ * such directly equating the two source clocks is impossible.
+ */
+struct clk clk_mpllref = {
+	.name		= "mpllref",
+	.parent		= &clk_xtal,
+	.id		= -1,
+};
+
+static struct clk *clk_epllref_sources[] = {
+	[0] = &clk_mpllref,
+	[1] = &clk_mpllref,
+	[2] = &clk_xtal,
+	[3] = &clk_ext,
+};
+
+struct clksrc_clk clk_epllref = {
+	.clk	= {
+		.name		= "epllref",
+		.id		= -1,
+	},
+	.sources = &(struct clksrc_sources) {
+		.sources = clk_epllref_sources,
+		.nr_sources = ARRAY_SIZE(clk_epllref_sources),
+	},
+	.reg_src = { .reg = S3C2443_CLKSRC, .size = 2, .shift = 7 },
+};
+
+/* esysclk
+ *
+ * this is sourced from either the EPLL or the EPLLref clock
+*/
+
+static struct clk *clk_sysclk_sources[] = {
+	[0] = &clk_epllref.clk,
+	[1] = &clk_epll,
+};
+
+struct clksrc_clk clk_esysclk = {
+	.clk	= {
+		.name		= "esysclk",
+		.parent		= &clk_epll,
+		.id		= -1,
+	},
+	.sources = &(struct clksrc_sources) {
+		.sources = clk_sysclk_sources,
+		.nr_sources = ARRAY_SIZE(clk_sysclk_sources),
+	},
+	.reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 6 },
+};
+
+static unsigned long s3c2443_getrate_mdivclk(struct clk *clk)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long div = __raw_readl(S3C2443_CLKDIV0);
+
+	div  &= S3C2443_CLKDIV0_EXTDIV_MASK;
+	div >>= (S3C2443_CLKDIV0_EXTDIV_SHIFT-1);	/* x2 */
+
+	return parent_rate / (div + 1);
+}
+
+static struct clk clk_mdivclk = {
+	.name		= "mdivclk",
+	.parent		= &clk_mpllref,
+	.id		= -1,
+	.ops		= &(struct clk_ops) {
+		.get_rate	= s3c2443_getrate_mdivclk,
+	},
+};
+
+static struct clk *clk_msysclk_sources[] = {
+	[0] = &clk_mpllref,
+	[1] = &clk_mpll,
+	[2] = &clk_mdivclk,
+	[3] = &clk_mpllref,
+};
+
+struct clksrc_clk clk_msysclk = {
+	.clk	= {
+		.name		= "msysclk",
+		.parent		= &clk_xtal,
+		.id		= -1,
+	},
+	.sources = &(struct clksrc_sources) {
+		.sources = clk_msysclk_sources,
+		.nr_sources = ARRAY_SIZE(clk_msysclk_sources),
+	},
+	.reg_src = { .reg = S3C2443_CLKSRC, .size = 2, .shift = 3 },
+};
+
+/* prediv
+ *
+ * this divides the msysclk down to pass to h/p/etc.
+ */
+
+static unsigned long s3c2443_prediv_getrate(struct clk *clk)
+{
+	unsigned long rate = clk_get_rate(clk->parent);
+	unsigned long clkdiv0 = __raw_readl(S3C2443_CLKDIV0);
+
+	clkdiv0 &= S3C2443_CLKDIV0_PREDIV_MASK;
+	clkdiv0 >>= S3C2443_CLKDIV0_PREDIV_SHIFT;
+
+	return rate / (clkdiv0 + 1);
+}
+
+static struct clk clk_prediv = {
+	.name		= "prediv",
+	.id		= -1,
+	.parent		= &clk_msysclk.clk,
+	.ops		= &(struct clk_ops) {
+		.get_rate	= s3c2443_prediv_getrate,
+	},
+};
+
+/* usbhost
+ *
+ * usb host bus-clock, usually 48MHz to provide USB bus clock timing
+*/
+
+static struct clksrc_clk clk_usb_bus_host = {
+	.clk	= {
+		.name		= "usb-bus-host-parent",
+		.id		= -1,
+		.parent		= &clk_esysclk.clk,
+		.ctrlbit	= S3C2443_SCLKCON_USBHOST,
+		.enable		= s3c2443_clkcon_enable_s,
+	},
+	.reg_div = { .reg = S3C2443_CLKDIV1, .size = 2, .shift = 4 },
+};
+
+/* common clksrc clocks */
+
+static struct clksrc_clk clksrc_clks[] = {
+	{
+		/* ART baud-rate clock sourced from esysclk via a divisor */
+		.clk	= {
+			.name		= "uartclk",
+			.id		= -1,
+			.parent		= &clk_esysclk.clk,
+		},
+		.reg_div = { .reg = S3C2443_CLKDIV1, .size = 4, .shift = 8 },
+	}, {
+		/* camera interface bus-clock, divided down from esysclk */
+		.clk	= {
+			.name		= "camif-upll",	/* same as 2440 name */
+			.id		= -1,
+			.parent		= &clk_esysclk.clk,
+			.ctrlbit	= S3C2443_SCLKCON_CAMCLK,
+			.enable		= s3c2443_clkcon_enable_s,
+		},
+		.reg_div = { .reg = S3C2443_CLKDIV1, .size = 4, .shift = 26 },
+	}, {
+		.clk	= {
+			.name		= "display-if",
+			.id		= -1,
+			.parent		= &clk_esysclk.clk,
+			.ctrlbit	= S3C2443_SCLKCON_DISPCLK,
+			.enable		= s3c2443_clkcon_enable_s,
+		},
+		.reg_div = { .reg = S3C2443_CLKDIV1, .size = 8, .shift = 16 },
+	},
+};
+
+
+static struct clk init_clocks_off[] = {
+	{
+		.name		= "adc",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_ADC,
+	}, {
+		.name		= "i2c",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_IIC,
+	}
+};
+
+static struct clk init_clocks[] = {
+	{
+		.name		= "dma",
+		.id		= 0,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_DMA0,
+	}, {
+		.name		= "dma",
+		.id		= 1,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_DMA1,
+	}, {
+		.name		= "dma",
+		.id		= 2,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_DMA2,
+	}, {
+		.name		= "dma",
+		.id		= 3,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_DMA3,
+	}, {
+		.name		= "dma",
+		.id		= 4,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_DMA4,
+	}, {
+		.name		= "dma",
+		.id		= 5,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_DMA5,
+	}, {
+		.name		= "hsmmc",
+		.id		= 0,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_HSMMC,
+	}, {
+		.name		= "gpio",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_GPIO,
+	}, {
+		.name		= "usb-host",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_USBH,
+	}, {
+		.name		= "usb-device",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_USBD,
+	}, {
+		.name		= "lcd",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_LCDC,
+
+	}, {
+		.name		= "timers",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_PWMT,
+	}, {
+		.name		= "cfc",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_CFC,
+	}, {
+		.name		= "ssmc",
+		.id		= -1,
+		.parent		= &clk_h,
+		.enable		= s3c2443_clkcon_enable_h,
+		.ctrlbit	= S3C2443_HCLKCON_SSMC,
+	}, {
+		.name		= "uart",
+		.id		= 0,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_UART0,
+	}, {
+		.name		= "uart",
+		.id		= 1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_UART1,
+	}, {
+		.name		= "uart",
+		.id		= 2,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_UART2,
+	}, {
+		.name		= "uart",
+		.id		= 3,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_UART3,
+	}, {
+		.name		= "rtc",
+		.id		= -1,
+		.parent		= &clk_p,
+		.enable		= s3c2443_clkcon_enable_p,
+		.ctrlbit	= S3C2443_PCLKCON_RTC,
+	}, {
+		.name		= "watchdog",
+		.id		= -1,
+		.parent		= &clk_p,
+		.ctrlbit	= S3C2443_PCLKCON_WDT,
+	}, {
+		.name		= "ac97",
+		.id		= -1,
+		.parent		= &clk_p,
+		.ctrlbit	= S3C2443_PCLKCON_AC97,
+	}, {
+		.name		= "nand",
+		.id		= -1,
+		.parent		= &clk_h,
+	}, {
+		.name		= "usb-bus-host",
+		.id		= -1,
+		.parent		= &clk_usb_bus_host.clk,
+	}
+};
+
+static inline unsigned long s3c2443_get_hdiv(unsigned long clkcon0)
+{
+	clkcon0 &= S3C2443_CLKDIV0_HCLKDIV_MASK;
+
+	return clkcon0 + 1;
+}
+
+/* EPLLCON compatible enough to get on/off information */
+
+void __init_or_cpufreq s3c2443_common_setup_clocks(pll_fn get_mpll,
+						   fdiv_fn get_fdiv)
+{
+	unsigned long epllcon = __raw_readl(S3C2443_EPLLCON);
+	unsigned long mpllcon = __raw_readl(S3C2443_MPLLCON);
+	unsigned long clkdiv0 = __raw_readl(S3C2443_CLKDIV0);
+	struct clk *xtal_clk;
+	unsigned long xtal;
+	unsigned long pll;
+	unsigned long fclk;
+	unsigned long hclk;
+	unsigned long pclk;
+	int ptr;
+
+	xtal_clk = clk_get(NULL, "xtal");
+	xtal = clk_get_rate(xtal_clk);
+	clk_put(xtal_clk);
+
+	pll = get_mpll(mpllcon, xtal);
+	clk_msysclk.clk.rate = pll;
+
+	fclk = pll / get_fdiv(clkdiv0);
+	hclk = s3c2443_prediv_getrate(&clk_prediv);
+	hclk /= s3c2443_get_hdiv(clkdiv0);
+	pclk = hclk / ((clkdiv0 & S3C2443_CLKDIV0_HALF_PCLK) ? 2 : 1);
+
+	s3c24xx_setup_clocks(fclk, hclk, pclk);
+
+	printk("CPU: MPLL %s %ld.%03ld MHz, cpu %ld.%03ld MHz, mem %ld.%03ld MHz, pclk %ld.%03ld MHz\n",
+	       (mpllcon & S3C2443_PLLCON_OFF) ? "off":"on",
+	       print_mhz(pll), print_mhz(fclk),
+	       print_mhz(hclk), print_mhz(pclk));
+
+	for (ptr = 0; ptr < ARRAY_SIZE(clksrc_clks); ptr++)
+		s3c_set_clksrc(&clksrc_clks[ptr], true);
+
+	/* ensure usb bus clock is within correct rate of 48MHz */
+
+	if (clk_get_rate(&clk_usb_bus_host.clk) != (48 * 1000 * 1000)) {
+		printk(KERN_INFO "Warning: USB host bus not at 48MHz\n");
+		clk_set_rate(&clk_usb_bus_host.clk, 48*1000*1000);
+	}
+
+	printk("CPU: EPLL %s %ld.%03ld MHz, usb-bus %ld.%03ld MHz\n",
+	       (epllcon & S3C2443_PLLCON_OFF) ? "off":"on",
+	       print_mhz(clk_get_rate(&clk_epll)),
+	       print_mhz(clk_get_rate(&clk_usb_bus)));
+}
+
+static struct clk *clks[] __initdata = {
+	&clk_prediv,
+	&clk_mpllref,
+	&clk_mdivclk,
+	&clk_ext,
+	&clk_epll,
+	&clk_usb_bus,
+};
+
+static struct clksrc_clk *clksrcs[] __initdata = {
+	&clk_usb_bus_host,
+	&clk_epllref,
+	&clk_esysclk,
+	&clk_msysclk,
+};
+
+void __init s3c2443_common_init_clocks(int xtal, pll_fn get_mpll,
+				       fdiv_fn get_fdiv)
+{
+	int ptr;
+
+	/* s3c2443 parents h and p clocks from prediv */
+	clk_h.parent = &clk_prediv;
+	clk_p.parent = &clk_prediv;
+
+	clk_usb_bus.parent = &clk_usb_bus_host.clk;
+	clk_epll.parent = &clk_epllref.clk;
+
+	s3c24xx_register_baseclocks(xtal);
+	s3c24xx_register_clocks(clks, ARRAY_SIZE(clks));
+
+	for (ptr = 0; ptr < ARRAY_SIZE(clksrcs); ptr++)
+		s3c_register_clksrc(clksrcs[ptr], 1);
+
+	s3c_register_clksrc(clksrc_clks, ARRAY_SIZE(clksrc_clks));
+	s3c_register_clocks(init_clocks, ARRAY_SIZE(init_clocks));
+
+	/* See s3c2443/etc notes on disabling clocks at init time */
+	s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+	s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off));
+
+	s3c2443_common_setup_clocks(get_mpll, get_fdiv);
+}

arch/arm/plat-s3c24xx/setup-i2c.c

@@ -15,12 +15,13 @@
 
 struct platform_device;
 
+#include <plat/gpio-cfg.h>
 #include <plat/iic.h>
 #include <mach/hardware.h>
 #include <mach/regs-gpio.h>
 
 void s3c_i2c0_cfg_gpio(struct platform_device *dev)
 {
-	s3c2410_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPE15_IICSDA);
-	s3c2410_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPE14_IICSCL);
+	s3c_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPE15_IICSDA);
+	s3c_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPE14_IICSCL);
 }

arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c

@@ -21,16 +21,16 @@ void s3c24xx_spi_gpiocfg_bus0_gpe11_12_13(struct s3c2410_spi_info *spi,
 					  int enable)
 {
 	if (enable) {
-		s3c2410_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPE13_SPICLK0);
-		s3c2410_gpio_cfgpin(S3C2410_GPE(12), S3C2410_GPE12_SPIMOSI0);
-		s3c2410_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPE11_SPIMISO0);
+		s3c_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPE13_SPICLK0);
+		s3c_gpio_cfgpin(S3C2410_GPE(12), S3C2410_GPE12_SPIMOSI0);
+		s3c_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPE11_SPIMISO0);
 		s3c2410_gpio_pullup(S3C2410_GPE(11), 0);
 		s3c2410_gpio_pullup(S3C2410_GPE(13), 0);
 	} else {
-		s3c2410_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPIO_INPUT);
-		s3c2410_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPIO_INPUT);
-		s3c2410_gpio_pullup(S3C2410_GPE(11), 1);
-		s3c2410_gpio_pullup(S3C2410_GPE(12), 1);
-		s3c2410_gpio_pullup(S3C2410_GPE(13), 1);
+		s3c_gpio_cfgpin(S3C2410_GPE(13), S3C2410_GPIO_INPUT);
+		s3c_gpio_cfgpin(S3C2410_GPE(11), S3C2410_GPIO_INPUT);
+		s3c_gpio_cfgpull(S3C2410_GPE(11), S3C_GPIO_PULL_NONE);
+		s3c_gpio_cfgpull(S3C2410_GPE(12), S3C_GPIO_PULL_NONE);
+		s3c_gpio_cfgpull(S3C2410_GPE(13), S3C_GPIO_PULL_NONE);
 	}
 }

arch/arm/plat-s3c24xx/spi-bus1-gpd8_9_10.c

@@ -23,16 +23,16 @@ void s3c24xx_spi_gpiocfg_bus1_gpd8_9_10(struct s3c2410_spi_info *spi,
 
 	printk(KERN_INFO "%s(%d)\n", __func__, enable);
 	if (enable) {
-		s3c2410_gpio_cfgpin(S3C2410_GPD(10), S3C2440_GPD10_SPICLK1);
-		s3c2410_gpio_cfgpin(S3C2410_GPD(9), S3C2440_GPD9_SPIMOSI1);
-		s3c2410_gpio_cfgpin(S3C2410_GPD(8), S3C2440_GPD8_SPIMISO1);
+		s3c_gpio_cfgpin(S3C2410_GPD(10), S3C2440_GPD10_SPICLK1);
+		s3c_gpio_cfgpin(S3C2410_GPD(9), S3C2440_GPD9_SPIMOSI1);
+		s3c_gpio_cfgpin(S3C2410_GPD(8), S3C2440_GPD8_SPIMISO1);
 		s3c2410_gpio_pullup(S3C2410_GPD(10), 0);
 		s3c2410_gpio_pullup(S3C2410_GPD(9), 0);
 	} else {
-		s3c2410_gpio_cfgpin(S3C2410_GPD(8), S3C2410_GPIO_INPUT);
-		s3c2410_gpio_cfgpin(S3C2410_GPD(9), S3C2410_GPIO_INPUT);
-		s3c2410_gpio_pullup(S3C2410_GPD(10), 1);
-		s3c2410_gpio_pullup(S3C2410_GPD(9), 1);
-		s3c2410_gpio_pullup(S3C2410_GPD(8), 1);
+		s3c_gpio_cfgpin(S3C2410_GPD(8), S3C2410_GPIO_INPUT);
+		s3c_gpio_cfgpin(S3C2410_GPD(9), S3C2410_GPIO_INPUT);
+		s3c_gpio_cfgpull(S3C2410_GPD(10), S3C_GPIO_PULL_NONE);
+		s3c_gpio_cfgpull(S3C2410_GPD(9), S3C_GPIO_PULL_NONE);
+		s3c_gpio_cfgpull(S3C2410_GPD(8), S3C_GPIO_PULL_NONE);
 	}
 }

arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c

@@ -21,16 +21,16 @@ void s3c24xx_spi_gpiocfg_bus1_gpg5_6_7(struct s3c2410_spi_info *spi,
 				       int enable)
 {
 	if (enable) {
-		s3c2410_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPG7_SPICLK1);
-		s3c2410_gpio_cfgpin(S3C2410_GPG(6), S3C2410_GPG6_SPIMOSI1);
-		s3c2410_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPG5_SPIMISO1);
+		s3c_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPG7_SPICLK1);
+		s3c_gpio_cfgpin(S3C2410_GPG(6), S3C2410_GPG6_SPIMOSI1);
+		s3c_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPG5_SPIMISO1);
 		s3c2410_gpio_pullup(S3C2410_GPG(5), 0);
 		s3c2410_gpio_pullup(S3C2410_GPG(6), 0);
 	} else {
-		s3c2410_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPIO_INPUT);
-		s3c2410_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPIO_INPUT);
-		s3c2410_gpio_pullup(S3C2410_GPG(5), 1);
-		s3c2410_gpio_pullup(S3C2410_GPG(6), 1);
-		s3c2410_gpio_pullup(S3C2410_GPG(7), 1);
+		s3c_gpio_cfgpin(S3C2410_GPG(7), S3C2410_GPIO_INPUT);
+		s3c_gpio_cfgpin(S3C2410_GPG(5), S3C2410_GPIO_INPUT);
+		s3c_gpio_cfgpull(S3C2410_GPG(5), S3C_GPIO_PULL_NONE);
+		s3c_gpio_cfgpull(S3C2410_GPG(6), S3C_GPIO_PULL_NONE);
+		s3c_gpio_cfgpull(S3C2410_GPG(7), S3C_GPIO_PULL_NONE);
 	}
 }

arch/arm/plat-samsung/clock.c

@@ -376,6 +376,21 @@ void __init s3c_register_clocks(struct clk *clkp, int nr_clks)
 	}
 }
 
+/**
+ * s3c_disable_clocks() - disable an array of clocks
+ * @clkp: Pointer to the first clock in the array.
+ * @nr_clks: Number of clocks to register.
+ *
+ * for internal use only at initialisation time. disable the clocks in the
+ * @clkp array.
+ */
+
+void __init s3c_disable_clocks(struct clk *clkp, int nr_clks)
+{
+	for (; nr_clks > 0; nr_clks--, clkp++)
+		(clkp->enable)(clkp, 0);
+}
+
 /* initalise all the clocks */
 
 int __init s3c24xx_register_baseclocks(unsigned long xtal)

arch/arm/plat-samsung/gpio-config.c

 /* linux/arch/arm/plat-s3c/gpio-config.c
  *
  * Copyright 2008 Openmoko, Inc.
- * Copyright 2008 Simtec Electronics
+ * Copyright 2008-2010 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
  *	http://armlinux.simtec.co.uk/
  *
@@ -41,6 +41,26 @@ int s3c_gpio_cfgpin(unsigned int pin, unsigned int config)
 }
 EXPORT_SYMBOL(s3c_gpio_cfgpin);
 
+unsigned s3c_gpio_getcfg(unsigned int pin)
+{
+	struct s3c_gpio_chip *chip = s3c_gpiolib_getchip(pin);
+	unsigned long flags;
+	unsigned ret = 0;
+	int offset;
+
+	if (chip) {
+		offset = pin - chip->chip.base;
+
+		local_irq_save(flags);
+		ret = s3c_gpio_do_getcfg(chip, offset);
+		local_irq_restore(flags);
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL(s3c_gpio_getcfg);
+
+
 int s3c_gpio_setpull(unsigned int pin, s3c_gpio_pull_t pull)
 {
 	struct s3c_gpio_chip *chip = s3c_gpiolib_getchip(pin);
@@ -61,8 +81,8 @@ int s3c_gpio_setpull(unsigned int pin, s3c_gpio_pull_t pull)
 EXPORT_SYMBOL(s3c_gpio_setpull);
 
 #ifdef CONFIG_S3C_GPIO_CFG_S3C24XX
-int s3c_gpio_setcfg_s3c24xx_banka(struct s3c_gpio_chip *chip,
-				  unsigned int off, unsigned int cfg)
+int s3c_gpio_setcfg_s3c24xx_a(struct s3c_gpio_chip *chip,
+			      unsigned int off, unsigned int cfg)
 {
 	void __iomem *reg = chip->base;
 	unsigned int shift = off;
@@ -87,6 +107,19 @@ int s3c_gpio_setcfg_s3c24xx_banka(struct s3c_gpio_chip *chip,
 	return 0;
 }
 
+unsigned s3c_gpio_getcfg_s3c24xx_a(struct s3c_gpio_chip *chip,
+				   unsigned int off)
+{
+	u32 con;
+
+	con = __raw_readl(chip->base);
+	con >>= off;
+	con &= 1;
+	con++;
+
+	return S3C_GPIO_SFN(con);
+}
+
 int s3c_gpio_setcfg_s3c24xx(struct s3c_gpio_chip *chip,
 			    unsigned int off, unsigned int cfg)
 {
@@ -109,6 +142,19 @@ int s3c_gpio_setcfg_s3c24xx(struct s3c_gpio_chip *chip,
 
 	return 0;
 }
+
+unsigned int s3c_gpio_getcfg_s3c24xx(struct s3c_gpio_chip *chip,
+				     unsigned int off)
+{
+	u32 con;
+
+	con = __raw_readl(chip->base);
+	con >>= off * 2;
+	con &= 3;
+
+	/* this conversion works for IN and OUT as well as special mode */
+	return S3C_GPIO_SPECIAL(con);
+}
 #endif
 
 #ifdef CONFIG_S3C_GPIO_CFG_S3C64XX
@@ -134,6 +180,25 @@ int s3c_gpio_setcfg_s3c64xx_4bit(struct s3c_gpio_chip *chip,
 
 	return 0;
 }
+
+unsigned s3c_gpio_getcfg_s3c64xx_4bit(struct s3c_gpio_chip *chip,
+				      unsigned int off)
+{
+	void __iomem *reg = chip->base;
+	unsigned int shift = (off & 7) * 4;
+	u32 con;
+
+	if (off < 8 && chip->chip.ngpio > 8)
+		reg -= 4;
+
+	con = __raw_readl(reg);
+	con >>= shift;
+	con &= 0xf;
+
+	/* this conversion works for IN and OUT as well as special mode */
+	return S3C_GPIO_SPECIAL(con);
+}
+
 #endif /* CONFIG_S3C_GPIO_CFG_S3C64XX */
 
 #ifdef CONFIG_S3C_GPIO_PULL_UPDOWN
@@ -164,3 +229,35 @@ s3c_gpio_pull_t s3c_gpio_getpull_updown(struct s3c_gpio_chip *chip,
 	return (__force s3c_gpio_pull_t)pup;
 }
 #endif
+
+#ifdef CONFIG_S3C_GPIO_PULL_UP
+int s3c_gpio_setpull_1up(struct s3c_gpio_chip *chip,
+			 unsigned int off, s3c_gpio_pull_t pull)
+{
+	void __iomem *reg = chip->base + 0x08;
+	u32 pup = __raw_readl(reg);
+
+	pup = __raw_readl(reg);
+
+	if (pup == S3C_GPIO_PULL_UP)
+		pup &= ~(1 << off);
+	else if (pup == S3C_GPIO_PULL_NONE)
+		pup |= (1 << off);
+	else
+		return -EINVAL;
+
+	__raw_writel(pup, reg);
+	return 0;
+}
+
+s3c_gpio_pull_t s3c_gpio_getpull_1up(struct s3c_gpio_chip *chip,
+				     unsigned int off)
+{
+	void __iomem *reg = chip->base + 0x08;
+	u32 pup = __raw_readl(reg);
+
+	pup &= (1 << off);
+	return pup ? S3C_GPIO_PULL_NONE : S3C_GPIO_PULL_UP;
+}
+#endif /* CONFIG_S3C_GPIO_PULL_UP */
+

arch/arm/plat-samsung/include/plat/clock.h

@@ -91,6 +91,7 @@ extern int s3c24xx_register_clock(struct clk *clk);
 extern int s3c24xx_register_clocks(struct clk **clk, int nr_clks);
 
 extern void s3c_register_clocks(struct clk *clk, int nr_clks);
+extern void s3c_disable_clocks(struct clk *clkp, int nr_clks);
 
 extern int s3c24xx_register_baseclocks(unsigned long xtal);
 

arch/arm/plat-samsung/include/plat/cpu.h

@@ -73,6 +73,7 @@ extern struct sys_timer s3c24xx_timer;
 extern struct sysdev_class s3c2410_sysclass;
 extern struct sysdev_class s3c2410a_sysclass;
 extern struct sysdev_class s3c2412_sysclass;
+extern struct sysdev_class s3c2416_sysclass;
 extern struct sysdev_class s3c2440_sysclass;
 extern struct sysdev_class s3c2442_sysclass;
 extern struct sysdev_class s3c2443_sysclass;

arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h

@@ -30,6 +30,12 @@ static inline int s3c_gpio_do_setcfg(struct s3c_gpio_chip *chip,
 	return (chip->config->set_config)(chip, off, config);
 }
 
+static inline unsigned s3c_gpio_do_getcfg(struct s3c_gpio_chip *chip,
+					  unsigned int off)
+{
+	return (chip->config->get_config)(chip, off);
+}
+
 static inline int s3c_gpio_do_setpull(struct s3c_gpio_chip *chip,
 				      unsigned int off, s3c_gpio_pull_t pull)
 {
@@ -52,6 +58,18 @@ static inline int s3c_gpio_do_setpull(struct s3c_gpio_chip *chip,
 extern int s3c_gpio_setcfg_s3c24xx(struct s3c_gpio_chip *chip,
 				   unsigned int off, unsigned int cfg);
 
+/**
+ * s3c_gpio_getcfg_s3c24xx - S3C24XX style GPIO configuration read.
+ * @chip: The gpio chip that is being configured.
+ * @off: The offset for the GPIO being configured.
+ *
+ * The reverse of s3c_gpio_setcfg_s3c24xx(). Will return a value whicg
+ * could be directly passed back to s3c_gpio_setcfg_s3c24xx(), from the
+ * S3C_GPIO_SPECIAL() macro.
+ */
+unsigned int s3c_gpio_getcfg_s3c24xx(struct s3c_gpio_chip *chip,
+				     unsigned int off);
+
 /**
  * s3c_gpio_setcfg_s3c24xx_a - S3C24XX style GPIO configuration (Bank A)
  * @chip: The gpio chip that is being configured.
@@ -65,6 +83,21 @@ extern int s3c_gpio_setcfg_s3c24xx(struct s3c_gpio_chip *chip,
 extern int s3c_gpio_setcfg_s3c24xx_a(struct s3c_gpio_chip *chip,
 				     unsigned int off, unsigned int cfg);
 
+
+/**
+ * s3c_gpio_getcfg_s3c24xx_a - S3C24XX style GPIO configuration read (Bank A)
+ * @chip: The gpio chip that is being configured.
+ * @off: The offset for the GPIO being configured.
+ *
+ * The reverse of s3c_gpio_setcfg_s3c24xx_a() turning an GPIO into a usable
+ * GPIO configuration value.
+ *
+ * @sa s3c_gpio_getcfg_s3c24xx
+ * @sa s3c_gpio_getcfg_s3c64xx_4bit
+ */
+extern unsigned s3c_gpio_getcfg_s3c24xx_a(struct s3c_gpio_chip *chip,
+					  unsigned int off);
+
 /**
  * s3c_gpio_setcfg_s3c64xx_4bit - S3C64XX 4bit single register GPIO config.
  * @chip: The gpio chip that is being configured.
@@ -85,6 +118,20 @@ extern int s3c_gpio_setcfg_s3c64xx_4bit(struct s3c_gpio_chip *chip,
 					unsigned int off, unsigned int cfg);
 
 
+/**
+ * s3c_gpio_getcfg_s3c64xx_4bit - S3C64XX 4bit single register GPIO config read.
+ * @chip: The gpio chip that is being configured.
+ * @off: The offset for the GPIO being configured.
+ *
+ * The reverse of s3c_gpio_setcfg_s3c64xx_4bit(), turning a gpio configuration
+ * register setting into a value the software can use, such as could be passed
+ * to s3c_gpio_setcfg_s3c64xx_4bit().
+ *
+ * @sa s3c_gpio_getcfg_s3c24xx
+ */
+extern unsigned s3c_gpio_getcfg_s3c64xx_4bit(struct s3c_gpio_chip *chip,
+					     unsigned int off);
+
 /* Pull-{up,down} resistor controls.
  *
  * S3C2410,S3C2440,S3C24A0 = Pull-UP,
@@ -145,6 +192,17 @@ extern int s3c_gpio_setpull_updown(struct s3c_gpio_chip *chip,
 extern s3c_gpio_pull_t s3c_gpio_getpull_updown(struct s3c_gpio_chip *chip,
 					       unsigned int off);
 
+/**
+ * s3c_gpio_getpull_1up() - Get configuration for choice of up or none
+ * @chip: The gpio chip that the GPIO pin belongs to
+ * @off: The offset to the pin to get the configuration of.
+ *
+ * This helper function reads the state of the pull-up resistor for the
+ * given GPIO in the same case as s3c_gpio_setpull_1up.
+*/
+extern s3c_gpio_pull_t s3c_gpio_getpull_1up(struct s3c_gpio_chip *chip,
+					    unsigned int off);
+
 /**
  * s3c_gpio_setpull_s3c2443() - Pull configuration for s3c2443.
  * @chip: The gpio chip that is being configured.

arch/arm/plat-samsung/include/plat/gpio-cfg.h

@@ -77,6 +77,17 @@ struct s3c_gpio_cfg {
  */
 extern int s3c_gpio_cfgpin(unsigned int pin, unsigned int to);
 
+/**
+ * s3c_gpio_getcfg - Read the current function for a GPIO pin
+ * @pin: The pin to read the configuration value for.
+ *
+ * Read the configuration state of the given @pin, returning a value that
+ * could be passed back to s3c_gpio_cfgpin().
+ *
+ * @sa s3c_gpio_cfgpin
+ */
+extern unsigned s3c_gpio_getcfg(unsigned int pin);
+
 /* Define values for the pull-{up,down} available for each gpio pin.
  *
  * These values control the state of the weak pull-{up,down} resistors

arch/arm/plat-samsung/include/plat/gpio-core.h

@@ -108,6 +108,9 @@ extern void samsung_gpiolib_add_4bit2_chips(struct s3c_gpio_chip *chip,
 extern void samsung_gpiolib_add_4bit(struct s3c_gpio_chip *chip);
 extern void samsung_gpiolib_add_4bit2(struct s3c_gpio_chip *chip);
 
+/* exported for core SoC support to change */
+extern struct s3c_gpio_cfg s3c24xx_gpiocfg_default;
+
 #ifdef CONFIG_S3C_GPIO_TRACK
 extern struct s3c_gpio_chip *s3c_gpios[S3C_GPIO_END];
 

arch/arm/plat-samsung/include/plat/pll6553x.h

+/* arch/arm/plat-samsung/include/plat/pll6553x.h
+ *	partially from arch/arm/mach-s3c64xx/include/mach/pll.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * Samsung PLL6553x PLL code
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* S3C6400 and compatible (S3C2416, etc.) EPLL code */
+
+#define PLL6553X_MDIV_MASK	((1 << (23-16)) - 1)
+#define PLL6553X_PDIV_MASK	((1 << (13-8)) - 1)
+#define PLL6553X_SDIV_MASK	((1 << (2-0)) - 1)
+#define PLL6553X_MDIV_SHIFT	(16)
+#define PLL6553X_PDIV_SHIFT	(8)
+#define PLL6553X_SDIV_SHIFT	(0)
+#define PLL6553X_KDIV_MASK	(0xffff)
+
+static inline unsigned long s3c_get_pll6553x(unsigned long baseclk,
+					     u32 pll0, u32 pll1)
+{
+	unsigned long result;
+	u32 mdiv, pdiv, sdiv, kdiv;
+	u64 tmp;
+
+	mdiv = (pll0 >> PLL6553X_MDIV_SHIFT) & PLL6553X_MDIV_MASK;
+	pdiv = (pll0 >> PLL6553X_PDIV_SHIFT) & PLL6553X_PDIV_MASK;
+	sdiv = (pll0 >> PLL6553X_SDIV_SHIFT) & PLL6553X_SDIV_MASK;
+	kdiv = pll1 & PLL6553X_KDIV_MASK;
+
+	/* We need to multiple baseclk by mdiv (the integer part) and kdiv
+	 * which is in 2^16ths, so shift mdiv up (does not overflow) and
+	 * add kdiv before multiplying. The use of tmp is to avoid any
+	 * overflows before shifting bac down into result when multipling
+	 * by the mdiv and kdiv pair.
+	 */
+
+	tmp = baseclk;
+	tmp *= (mdiv << 16) + kdiv;
+	do_div(tmp, (pdiv << sdiv));
+	result = tmp >> 16;
+
+	return result;
+}

drivers/serial/Kconfig

@@ -518,12 +518,13 @@ config SERIAL_S3C2412
 	  Serial port support for the Samsung S3C2412 and S3C2413 SoC
 
 config SERIAL_S3C2440
-	tristate "Samsung S3C2440/S3C2442 Serial port support"
-	depends on SERIAL_SAMSUNG && (CPU_S3C2440 || CPU_S3C2442)
+	tristate "Samsung S3C2440/S3C2442/S3C2416 Serial port support"
+	depends on SERIAL_SAMSUNG && (CPU_S3C2440 || CPU_S3C2442 || CPU_S3C2416)
 	default y if CPU_S3C2440
 	default y if CPU_S3C2442
+	select SERIAL_SAMSUNG_UARTS_4 if CPU_S3C2416
 	help
-	  Serial port support for the Samsung S3C2440 and S3C2442 SoC
+	  Serial port support for the Samsung S3C2440, S3C2416 and S3C2442 SoC
 
 config SERIAL_S3C24A0
 	tristate "Samsung S3C24A0 Serial port support"