mmc: sdhci: R1B command handling + MMC_CAP_ERASE.

ERASE command needs R1B response, so fix R1B-type command
handling for SDHCI controller. For non-DAT commands using a busy
response, the cmd->cmd_timeout_ms (in ms) field is used for timeout
calculations.

Based on patch by Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

drivers/mmc/host/sdhci.c

@@ -40,7 +40,6 @@
 
 static unsigned int debug_quirks = 0;
 
-static void sdhci_prepare_data(struct sdhci_host *, struct mmc_data *);
 static void sdhci_finish_data(struct sdhci_host *);
 
 static void sdhci_send_command(struct sdhci_host *, struct mmc_command *);
@@ -591,9 +590,10 @@ static void sdhci_adma_table_post(struct sdhci_host *host,
 		data->sg_len, direction);
 }
 
-static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_data *data)
+static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd)
 {
 	u8 count;
+	struct mmc_data *data = cmd->data;
 	unsigned target_timeout, current_timeout;
 
 	/*
@@ -605,13 +605,17 @@ static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_data *data)
 	if (host->quirks & SDHCI_QUIRK_BROKEN_TIMEOUT_VAL)
 		return 0xE;
 
+	/* Unspecified timeout, assume max */
+	if (!data && !cmd->cmd_timeout_ms)
+		return 0xE;
+
 	/* timeout in us */
+	if (!data)
+		target_timeout = cmd->cmd_timeout_ms * 1000;
+	else
 		target_timeout = data->timeout_ns / 1000 +
 			data->timeout_clks / host->clock;
 
-	if (host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)
-		host->timeout_clk = host->clock / 1000;
-
 	/*
 	 * Figure out needed cycles.
 	 * We do this in steps in order to fit inside a 32 bit int.
@@ -632,8 +636,8 @@ static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_data *data)
 	}
 
 	if (count >= 0xF) {
-		printk(KERN_WARNING "%s: Too large timeout requested!\n",
-			mmc_hostname(host->mmc));
+		printk(KERN_WARNING "%s: Too large timeout requested for CMD%d!\n",
+		       mmc_hostname(host->mmc), cmd->opcode);
 		count = 0xE;
 	}
 
@@ -651,15 +655,21 @@ static void sdhci_set_transfer_irqs(struct sdhci_host *host)
 		sdhci_clear_set_irqs(host, dma_irqs, pio_irqs);
 }
 
-static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data)
+static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
 {
 	u8 count;
 	u8 ctrl;
+	struct mmc_data *data = cmd->data;
 	int ret;
 
 	WARN_ON(host->data);
 
-	if (data == NULL)
+	if (data || (cmd->flags & MMC_RSP_BUSY)) {
+		count = sdhci_calc_timeout(host, cmd);
+		sdhci_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
+	}
+
+	if (!data)
 		return;
 
 	/* Sanity checks */
@@ -670,9 +680,6 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data)
 	host->data = data;
 	host->data_early = 0;
 
-	count = sdhci_calc_timeout(host, data);
-	sdhci_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
-
 	if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA))
 		host->flags |= SDHCI_REQ_USE_DMA;
 
@@ -920,7 +927,7 @@ static void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
 
 	host->cmd = cmd;
 
-	sdhci_prepare_data(host, cmd->data);
+	sdhci_prepare_data(host, cmd);
 
 	sdhci_writel(host, cmd->arg, SDHCI_ARGUMENT);
 
@@ -1874,6 +1881,9 @@ int sdhci_add_host(struct sdhci_host *host)
 	if (caps & SDHCI_TIMEOUT_CLK_UNIT)
 		host->timeout_clk *= 1000;
 
+	if (host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)
+		host->timeout_clk = host->clock / 1000;
+
 	/*
 	 * Set host parameters.
 	 */
@@ -1886,7 +1896,7 @@ int sdhci_add_host(struct sdhci_host *host)
 		mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_200;
 
 	mmc->f_max = host->max_clk;
-	mmc->caps |= MMC_CAP_SDIO_IRQ;
+	mmc->caps |= MMC_CAP_SDIO_IRQ | MMC_CAP_ERASE;
 
 	/*
 	 * A controller may support 8-bit width, but the board itself