Merge branch 'ks8695/boards' into next/boards

* ks8695/boards:
  ARM: ks8695: add board support for the OpenGear boards based on the KS8695
  ARM: ks8695: add board support for the SnapGear boards based on the KS8695

arch/arm/mach-ks8695/Kconfig

@@ -21,6 +21,67 @@ config MACH_ACS5K
 	  say 'Y' here if you want your kernel to run on the Brivo
 	  Systems LLC, ACS-5000 Master board.
 
+config MACH_LITE300
+	bool "SecureComputing SG300"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  SecureComputing / SnapGear SG300 VPN Internet Router.
+	  See http://www.securecomputing.com for more details.
+
+config MACH_SG310
+	bool "McAfee SG310"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  McAfee / SnapGear SG310 VPN Internet Router.
+	  See http://www.mcafee.com for more details.
+
+config MACH_SE4200
+	bool "SecureComputing SE4200"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  SecureComputing / SnapGear SE4200 Secure Wireless VPN
+	  Internet Router.
+	  See http://www.securecomputing.com for more details.
+
+config MACH_CM4002
+	bool "OpenGear CM4002"
+	help
+	  Say 'Y' here if you want your kernel to support the OpenGear
+	  CM4002 Secure Access Server. See http://www.opengear.com for
+	  more details.
+
+config MACH_CM4008
+	bool "OpenGear CM4008"
+	select MIGHT_HAVE_PCI
+	help
+	  Say 'Y' here if you want your kernel to support the OpenGear
+	  CM4008 Console Server. See http://www.opengear.com for more
+	  details.
+
+config MACH_CM41xx
+	bool "OpenGear CM41xx"
+	select MIGHT_HAVE_PCI
+	help
+	  Say 'Y' here if you want your kernel to support the OpenGear
+	  CM4016 or CM4048 Console Servers. See http://www.opengear.com for
+	  more details.
+
+config MACH_IM4004
+	bool "OpenGear IM4004"
+	select MIGHT_HAVE_PCI
+	help
+	  Say 'Y' here if you want your kernel to support the OpenGear
+	  IM4004 Secure Access Server. See http://www.opengear.com for
+	  more details.
+
+config MACH_IM42xx
+	bool "OpenGear IM42xx"
+	select MIGHT_HAVE_PCI
+	help
+	  Say 'Y' here if you want your kernel to support the OpenGear
+	  IM4216 or IM4248 Console Servers. See http://www.opengear.com for
+	  more details.
+
 endmenu
 
 endif

arch/arm/mach-ks8695/Makefile

@@ -18,3 +18,11 @@ obj-$(CONFIG_LEDS)		+= leds.o
 obj-$(CONFIG_MACH_KS8695)	+= board-micrel.o
 obj-$(CONFIG_MACH_DSM320)	+= board-dsm320.o
 obj-$(CONFIG_MACH_ACS5K)	+= board-acs5k.o
+obj-$(CONFIG_MACH_LITE300)	+= board-sg.o
+obj-$(CONFIG_MACH_SG310)	+= board-sg.o
+obj-$(CONFIG_MACH_SE4200)	+= board-sg.o
+obj-$(CONFIG_MACH_CM4002)	+= board-og.o
+obj-$(CONFIG_MACH_CM4008)	+= board-og.o
+obj-$(CONFIG_MACH_CM41xx)	+= board-og.o
+obj-$(CONFIG_MACH_IM4004)	+= board-og.o
+obj-$(CONFIG_MACH_IM42xx)	+= board-og.o

arch/arm/mach-ks8695/board-og.c

+/*
+ * board-og.c -- support for the OpenGear KS8695 based boards.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <mach/devices.h>
+#include <mach/regs-gpio.h>
+#include <mach/gpio-ks8695.h>
+#include "generic.h"
+
+static int og_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (machine_is_im4004() && (slot == 8))
+		return KS8695_IRQ_EXTERN1;
+	return KS8695_IRQ_EXTERN0;
+}
+
+static struct ks8695_pci_cfg __initdata og_pci = {
+	.mode		= KS8695_MODE_PCI,
+	.map_irq	= og_pci_map_irq,
+};
+
+static void __init og_register_pci(void)
+{
+	/* Initialize the GPIO lines for interrupt mode */
+	ks8695_gpio_interrupt(KS8695_GPIO_0, IRQ_TYPE_LEVEL_LOW);
+
+	/* Cardbus Slot */
+	if (machine_is_im4004())
+		ks8695_gpio_interrupt(KS8695_GPIO_1, IRQ_TYPE_LEVEL_LOW);
+
+	ks8695_init_pci(&og_pci);
+}
+
+/*
+ * The PCI bus reset is driven by a dedicated GPIO line. Toggle it here
+ * and bring the PCI bus out of reset.
+ */
+static void __init og_pci_bus_reset(void)
+{
+	unsigned int rstline = 1;
+
+	/* Some boards use a different GPIO as the PCI reset line */
+	if (machine_is_im4004())
+		rstline = 2;
+	else if (machine_is_im42xx())
+		rstline = 0;
+
+	gpio_request(rstline, "PCI reset");
+	gpio_direction_output(rstline, 0);
+
+	/* Drive a reset on the PCI reset line */
+	gpio_set_value(rstline, 1);
+	gpio_set_value(rstline, 0);
+	mdelay(100);
+	gpio_set_value(rstline, 1);
+	mdelay(100);
+}
+
+/*
+ * Direct connect serial ports (non-PCI that is).
+ */
+#define	S8250_PHYS	0x03800000
+#define	S8250_VIRT	0xf4000000
+#define	S8250_SIZE	0x00100000
+
+static struct __initdata map_desc og_io_desc[] = {
+	{
+		.virtual	= S8250_VIRT,
+		.pfn		= __phys_to_pfn(S8250_PHYS),
+		.length		= S8250_SIZE,
+		.type		= MT_DEVICE,
+	}
+};
+
+static struct resource og_uart_resources[] = {
+	{
+		.start		= S8250_VIRT,
+		.end		= S8250_VIRT + S8250_SIZE,
+		.flags		= IORESOURCE_MEM
+	},
+};
+
+static struct plat_serial8250_port og_uart_data[] = {
+	{
+		.mapbase	= S8250_VIRT,
+		.membase	= (char *) S8250_VIRT,
+		.irq		= 3,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= 115200 * 16,
+	},
+	{ },
+};
+
+static struct platform_device og_uart = {
+	.name			= "serial8250",
+	.id			= 0,
+	.dev.platform_data	= og_uart_data,
+	.num_resources		= 1,
+	.resource		= og_uart_resources
+};
+
+static struct platform_device *og_devices[] __initdata = {
+	&og_uart
+};
+
+static void __init og_init(void)
+{
+	ks8695_register_gpios();
+
+	if (machine_is_cm4002()) {
+		ks8695_gpio_interrupt(KS8695_GPIO_1, IRQ_TYPE_LEVEL_HIGH);
+		iotable_init(og_io_desc, ARRAY_SIZE(og_io_desc));
+		platform_add_devices(og_devices, ARRAY_SIZE(og_devices));
+	} else {
+		og_pci_bus_reset();
+		og_register_pci();
+	}
+
+	ks8695_add_device_lan();
+	ks8695_add_device_wan();
+}
+
+#ifdef CONFIG_MACH_CM4002
+MACHINE_START(CM4002, "OpenGear/CM4002")
+	/* OpenGear Inc. */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= og_init,
+	.timer		= &ks8695_timer,
+	.restart        = ks8695_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_CM4008
+MACHINE_START(CM4008, "OpenGear/CM4008")
+	/* OpenGear Inc. */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= og_init,
+	.timer		= &ks8695_timer,
+	.restart        = ks8695_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_CM41xx
+MACHINE_START(CM41XX, "OpenGear/CM41xx")
+	/* OpenGear Inc. */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= og_init,
+	.timer		= &ks8695_timer,
+	.restart        = ks8695_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_IM4004
+MACHINE_START(IM4004, "OpenGear/IM4004")
+	/* OpenGear Inc. */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= og_init,
+	.timer		= &ks8695_timer,
+	.restart        = ks8695_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_IM42xx
+MACHINE_START(IM42XX, "OpenGear/IM42xx")
+	/* OpenGear Inc. */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= og_init,
+	.timer		= &ks8695_timer,
+	.restart        = ks8695_restart,
+MACHINE_END
+#endif

arch/arm/mach-ks8695/board-sg.c

+/*
+ * board-sg.c -- support for the SnapGear KS8695 based boards
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/physmap.h>
+#include <linux/mtd/partitions.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/devices.h>
+#include "generic.h"
+
+/*
+ * The SG310 machine type is fitted with a conventional 8MB Strataflash
+ * device. Define its partitioning.
+ */
+#define	FL_BASE		0x02000000
+#define	FL_SIZE		SZ_8M
+
+static struct mtd_partition sg_mtd_partitions[] = {
+	[0] = {
+		.name	= "SnapGear Boot Loader",
+		.size	= SZ_128K,
+	},
+	[1] = {
+		.name	= "SnapGear non-volatile configuration",
+		.size	= SZ_512K,
+		.offset	= SZ_256K,
+	},
+	[2] = {
+		.name	= "SnapGear image",
+		.offset	= SZ_512K + SZ_256K,
+	},
+	[3] = {
+		.name	= "SnapGear StrataFlash",
+	},
+	[4] = {
+		.name	= "SnapGear Boot Tags",
+		.size	= SZ_128K,
+		.offset	= SZ_128K,
+	},
+};
+
+static struct physmap_flash_data sg_mtd_pdata = {
+	.width		= 1,
+	.nr_parts	= ARRAY_SIZE(sg_mtd_partitions),
+	.parts		= sg_mtd_partitions,
+};
+
+
+static struct resource sg_mtd_resource[] = {
+	[0] = {
+		.start = FL_BASE,
+		.end   = FL_BASE + FL_SIZE - 1,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device sg_mtd_device = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(sg_mtd_resource),
+	.resource	= sg_mtd_resource,
+	.dev		= {
+		.platform_data = &sg_mtd_pdata,
+	},
+};
+
+static void __init sg_init(void)
+{
+	ks8695_add_device_lan();
+	ks8695_add_device_wan();
+
+	if (machine_is_sg310())
+		platform_device_register(&sg_mtd_device);
+}
+
+#ifdef CONFIG_MACH_LITE300
+MACHINE_START(LITE300, "SecureComputing/SG300")
+	/* SnapGear */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= sg_init,
+	.timer		= &ks8695_timer,
+	.restart	= ks8695_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_SG310
+MACHINE_START(SG310, "McAfee/SG310")
+	/* SnapGear */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= sg_init,
+	.timer		= &ks8695_timer,
+	.restart	= ks8695_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_SE4200
+MACHINE_START(SE4200, "SecureComputing/SE4200")
+	/* SnapGear */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= sg_init,
+	.timer		= &ks8695_timer,
+	.restart	= ks8695_restart,
+MACHINE_END
+#endif