e1000e: add support for 82577/82578 GbE LOM parts

This patch provides support for the next generation Intel desktop
and mobile gigabit ethernet LOM adapters.  These adapters are the
follow-on parts to the LOMs tied to the prior ICH chipsets and are
comprised of a MAC in the PCH chipset and an external PHY (82577 for
mobile and 82578 for desktop versions).  New features consist of PHY
wakeup to save power by completely turning off the MAC while in Sx
state, and 4K jumbo frames.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/e1000e/82571.c

@@ -1587,6 +1587,7 @@ static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw)
 static struct e1000_mac_operations e82571_mac_ops = {
 	/* .check_mng_mode: mac type dependent */
 	/* .check_for_link: media type dependent */
+	.id_led_init		= e1000e_id_led_init,
 	.cleanup_led		= e1000e_cleanup_led_generic,
 	.clear_hw_cntrs		= e1000_clear_hw_cntrs_82571,
 	.get_bus_info		= e1000e_get_bus_info_pcie,
@@ -1598,6 +1599,7 @@ static struct e1000_mac_operations e82571_mac_ops = {
 	.init_hw		= e1000_init_hw_82571,
 	.setup_link		= e1000_setup_link_82571,
 	/* .setup_physical_interface: media type dependent */
+	.setup_led		= e1000e_setup_led_generic,
 };
 
 static struct e1000_phy_operations e82_phy_ops_igp = {

drivers/net/e1000e/defines.h

@@ -56,6 +56,7 @@
 /* Wake Up Control */
 #define E1000_WUC_APME       0x00000001 /* APM Enable */
 #define E1000_WUC_PME_EN     0x00000002 /* PME Enable */
+#define E1000_WUC_PHY_WAKE   0x00000100 /* if PHY supports wakeup */
 
 /* Wake Up Filter Control */
 #define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
@@ -65,6 +66,13 @@
 #define E1000_WUFC_BC   0x00000010 /* Broadcast Wakeup Enable */
 #define E1000_WUFC_ARP  0x00000020 /* ARP Request Packet Wakeup Enable */
 
+/* Wake Up Status */
+#define E1000_WUS_LNKC         E1000_WUFC_LNKC
+#define E1000_WUS_MAG          E1000_WUFC_MAG
+#define E1000_WUS_EX           E1000_WUFC_EX
+#define E1000_WUS_MC           E1000_WUFC_MC
+#define E1000_WUS_BC           E1000_WUFC_BC
+
 /* Extended Device Control */
 #define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */
 #define E1000_CTRL_EXT_EE_RST    0x00002000 /* Reinitialize from EEPROM */
@@ -77,6 +85,7 @@
 #define E1000_CTRL_EXT_IAME           0x08000000 /* Interrupt acknowledge Auto-mask */
 #define E1000_CTRL_EXT_INT_TIMER_CLR  0x20000000 /* Clear Interrupt timers after IMS clear */
 #define E1000_CTRL_EXT_PBA_CLR        0x80000000 /* PBA Clear */
+#define E1000_CTRL_EXT_PHYPDEN        0x00100000
 
 /* Receive Descriptor bit definitions */
 #define E1000_RXD_STAT_DD       0x01    /* Descriptor Done */
@@ -140,6 +149,7 @@
 #define E1000_RCTL_DTYP_PS        0x00000400    /* Packet Split descriptor */
 #define E1000_RCTL_RDMTS_HALF     0x00000000    /* Rx desc min threshold size */
 #define E1000_RCTL_MO_SHIFT       12            /* multicast offset shift */
+#define E1000_RCTL_MO_3           0x00003000    /* multicast offset 15:4 */
 #define E1000_RCTL_BAM            0x00008000    /* broadcast enable */
 /* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
 #define E1000_RCTL_SZ_2048        0x00000000    /* Rx buffer size 2048 */
@@ -153,6 +163,7 @@
 #define E1000_RCTL_VFE            0x00040000    /* vlan filter enable */
 #define E1000_RCTL_CFIEN          0x00080000    /* canonical form enable */
 #define E1000_RCTL_CFI            0x00100000    /* canonical form indicator */
+#define E1000_RCTL_PMCF           0x00800000    /* pass MAC control frames */
 #define E1000_RCTL_BSEX           0x02000000    /* Buffer size extension */
 #define E1000_RCTL_SECRC          0x04000000    /* Strip Ethernet CRC */
 
@@ -255,11 +266,16 @@
 #define AUTONEG_ADVERTISE_SPEED_DEFAULT   E1000_ALL_SPEED_DUPLEX
 
 /* LED Control */
+#define E1000_PHY_LED0_MODE_MASK          0x00000007
+#define E1000_PHY_LED0_IVRT               0x00000008
+#define E1000_PHY_LED0_MASK               0x0000001F
+
 #define E1000_LEDCTL_LED0_MODE_MASK       0x0000000F
 #define E1000_LEDCTL_LED0_MODE_SHIFT      0
 #define E1000_LEDCTL_LED0_IVRT            0x00000040
 #define E1000_LEDCTL_LED0_BLINK           0x00000080
 
+#define E1000_LEDCTL_MODE_LINK_UP       0x2
 #define E1000_LEDCTL_MODE_LED_ON        0xE
 #define E1000_LEDCTL_MODE_LED_OFF       0xF
 
@@ -676,6 +692,8 @@
 #define IFE_C_E_PHY_ID       0x02A80310
 #define BME1000_E_PHY_ID     0x01410CB0
 #define BME1000_E_PHY_ID_R2  0x01410CB1
+#define I82577_E_PHY_ID      0x01540050
+#define I82578_E_PHY_ID      0x004DD040
 
 /* M88E1000 Specific Registers */
 #define M88E1000_PHY_SPEC_CTRL     0x10  /* PHY Specific Control Register */
@@ -729,6 +747,9 @@
 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK  0x0E00
 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X    0x0800
 
+#define I82578_EPSCR_DOWNSHIFT_ENABLE          0x0020
+#define I82578_EPSCR_DOWNSHIFT_COUNTER_MASK    0x001C
+
 /* BME1000 PHY Specific Control Register */
 #define BME1000_PSCR_ENABLE_DOWNSHIFT   0x0800 /* 1 = enable downshift */
 

drivers/net/e1000e/e1000.h

@@ -98,6 +98,49 @@ struct e1000_info;
 
 #define DEFAULT_JUMBO			9234
 
+/* BM/HV Specific Registers */
+#define BM_PORT_CTRL_PAGE                 769
+
+#define PHY_UPPER_SHIFT                   21
+#define BM_PHY_REG(page, reg) \
+	(((reg) & MAX_PHY_REG_ADDRESS) |\
+	 (((page) & 0xFFFF) << PHY_PAGE_SHIFT) |\
+	 (((reg) & ~MAX_PHY_REG_ADDRESS) << (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)))
+
+/* PHY Wakeup Registers and defines */
+#define BM_RCTL         PHY_REG(BM_WUC_PAGE, 0)
+#define BM_WUC          PHY_REG(BM_WUC_PAGE, 1)
+#define BM_WUFC         PHY_REG(BM_WUC_PAGE, 2)
+#define BM_WUS          PHY_REG(BM_WUC_PAGE, 3)
+#define BM_RAR_L(_i)    (BM_PHY_REG(BM_WUC_PAGE, 16 + ((_i) << 2)))
+#define BM_RAR_M(_i)    (BM_PHY_REG(BM_WUC_PAGE, 17 + ((_i) << 2)))
+#define BM_RAR_H(_i)    (BM_PHY_REG(BM_WUC_PAGE, 18 + ((_i) << 2)))
+#define BM_RAR_CTRL(_i) (BM_PHY_REG(BM_WUC_PAGE, 19 + ((_i) << 2)))
+#define BM_MTA(_i)      (BM_PHY_REG(BM_WUC_PAGE, 128 + ((_i) << 1)))
+
+#define BM_RCTL_UPE           0x0001          /* Unicast Promiscuous Mode */
+#define BM_RCTL_MPE           0x0002          /* Multicast Promiscuous Mode */
+#define BM_RCTL_MO_SHIFT      3               /* Multicast Offset Shift */
+#define BM_RCTL_MO_MASK       (3 << 3)        /* Multicast Offset Mask */
+#define BM_RCTL_BAM           0x0020          /* Broadcast Accept Mode */
+#define BM_RCTL_PMCF          0x0040          /* Pass MAC Control Frames */
+#define BM_RCTL_RFCE          0x0080          /* Rx Flow Control Enable */
+
+#define HV_SCC_UPPER		PHY_REG(778, 16) /* Single Collision Count */
+#define HV_SCC_LOWER		PHY_REG(778, 17)
+#define HV_ECOL_UPPER		PHY_REG(778, 18) /* Excessive Collision Count */
+#define HV_ECOL_LOWER		PHY_REG(778, 19)
+#define HV_MCC_UPPER		PHY_REG(778, 20) /* Multiple Collision Count */
+#define HV_MCC_LOWER		PHY_REG(778, 21)
+#define HV_LATECOL_UPPER	PHY_REG(778, 23) /* Late Collision Count */
+#define HV_LATECOL_LOWER	PHY_REG(778, 24)
+#define HV_COLC_UPPER		PHY_REG(778, 25) /* Collision Count */
+#define HV_COLC_LOWER		PHY_REG(778, 26)
+#define HV_DC_UPPER		PHY_REG(778, 27) /* Defer Count */
+#define HV_DC_LOWER		PHY_REG(778, 28)
+#define HV_TNCRS_UPPER		PHY_REG(778, 29) /* Transmit with no CRS */
+#define HV_TNCRS_LOWER		PHY_REG(778, 30)
+
 enum e1000_boards {
 	board_82571,
 	board_82572,
@@ -108,6 +151,7 @@ enum e1000_boards {
 	board_ich8lan,
 	board_ich9lan,
 	board_ich10lan,
+	board_pchlan,
 };
 
 struct e1000_queue_stats {
@@ -305,6 +349,7 @@ struct e1000_adapter {
 	unsigned int flags2;
 	struct work_struct downshift_task;
 	struct work_struct update_phy_task;
+	struct work_struct led_blink_task;
 };
 
 struct e1000_info {
@@ -355,6 +400,7 @@ struct e1000_info {
 
 /* CRC Stripping defines */
 #define FLAG2_CRC_STRIPPING               (1 << 0)
+#define FLAG2_HAS_PHY_WAKEUP              (1 << 1)
 
 #define E1000_RX_DESC_PS(R, i)	    \
 	(&(((union e1000_rx_desc_packet_split *)((R).desc))[i]))
@@ -408,6 +454,7 @@ extern struct e1000_info e1000_82583_info;
 extern struct e1000_info e1000_ich8_info;
 extern struct e1000_info e1000_ich9_info;
 extern struct e1000_info e1000_ich10_info;
+extern struct e1000_info e1000_pch_info;
 extern struct e1000_info e1000_es2_info;
 
 extern s32 e1000e_read_pba_num(struct e1000_hw *hw, u32 *pba_num);
@@ -429,6 +476,7 @@ extern void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw);
 extern s32 e1000e_check_for_copper_link(struct e1000_hw *hw);
 extern s32 e1000e_check_for_fiber_link(struct e1000_hw *hw);
 extern s32 e1000e_check_for_serdes_link(struct e1000_hw *hw);
+extern s32 e1000e_setup_led_generic(struct e1000_hw *hw);
 extern s32 e1000e_cleanup_led_generic(struct e1000_hw *hw);
 extern s32 e1000e_led_on_generic(struct e1000_hw *hw);
 extern s32 e1000e_led_off_generic(struct e1000_hw *hw);
@@ -497,6 +545,15 @@ extern s32 e1000e_phy_reset_dsp(struct e1000_hw *hw);
 extern s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
 extern s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
 extern s32 e1000e_check_downshift(struct e1000_hw *hw);
+extern s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000_set_mdio_slow_mode_hv(struct e1000_hw *hw, bool slow);
+extern s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw);
+extern s32 e1000_copper_link_setup_82577(struct e1000_hw *hw);
+extern s32 e1000_check_polarity_82577(struct e1000_hw *hw);
+extern s32 e1000_get_phy_info_82577(struct e1000_hw *hw);
+extern s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw);
+extern s32 e1000_get_cable_length_82577(struct e1000_hw *hw);
 
 static inline s32 e1000_phy_hw_reset(struct e1000_hw *hw)
 {

drivers/net/e1000e/es2lan.c

@@ -1366,6 +1366,7 @@ static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw)
 }
 
 static struct e1000_mac_operations es2_mac_ops = {
+	.id_led_init		= e1000e_id_led_init,
 	.check_mng_mode		= e1000e_check_mng_mode_generic,
 	/* check_for_link dependent on media type */
 	.cleanup_led		= e1000e_cleanup_led_generic,
@@ -1379,6 +1380,7 @@ static struct e1000_mac_operations es2_mac_ops = {
 	.init_hw		= e1000_init_hw_80003es2lan,
 	.setup_link		= e1000e_setup_link,
 	/* setup_physical_interface dependent on media type */
+	.setup_led		= e1000e_setup_led_generic,
 };
 
 static struct e1000_phy_operations es2_phy_ops = {

drivers/net/e1000e/ethtool.c

@@ -776,6 +776,7 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
 	u32 after;
 	u32 i;
 	u32 toggle;
+	u32 mask;
 
 	/*
 	 * The status register is Read Only, so a write should fail.
@@ -788,16 +789,8 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
 	case e1000_80003es2lan:
 		toggle = 0x7FFFF3FF;
 		break;
-	case e1000_82573:
-	case e1000_82574:
-	case e1000_82583:
-	case e1000_ich8lan:
-	case e1000_ich9lan:
-	case e1000_ich10lan:
-		toggle = 0x7FFFF033;
-		break;
         default:
-		toggle = 0xFFFFF833;
+		toggle = 0x7FFFF033;
 		break;
 	}
 
@@ -844,11 +837,18 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
 		REG_PATTERN_TEST(E1000_TXCW, 0xC000FFFF, 0x0000FFFF);
 	REG_PATTERN_TEST(E1000_TDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
 	REG_PATTERN_TEST(E1000_TIDV, 0x0000FFFF, 0x0000FFFF);
+	mask = 0x8003FFFF;
+	switch (mac->type) {
+	case e1000_ich10lan:
+	case e1000_pchlan:
+		mask |= (1 << 18);
+		break;
+	default:
+		break;
+	}
 	for (i = 0; i < mac->rar_entry_count; i++)
 		REG_PATTERN_TEST_ARRAY(E1000_RA, ((i << 1) + 1),
-				       ((mac->type == e1000_ich10lan) ?
-					   0x8007FFFF : 0x8003FFFF),
-				       0xFFFFFFFF);
+		                       mask, 0xFFFFFFFF);
 
 	for (i = 0; i < mac->mta_reg_count; i++)
 		REG_PATTERN_TEST_ARRAY(E1000_MTA, i, 0xFFFFFFFF, 0xFFFFFFFF);
@@ -1786,15 +1786,22 @@ static int e1000_set_wol(struct net_device *netdev,
 /* bit defines for adapter->led_status */
 #define E1000_LED_ON		0
 
-static void e1000_led_blink_callback(unsigned long data)
+static void e1000e_led_blink_task(struct work_struct *work)
 {
-	struct e1000_adapter *adapter = (struct e1000_adapter *) data;
+	struct e1000_adapter *adapter = container_of(work,
+	                                struct e1000_adapter, led_blink_task);
 
 	if (test_and_change_bit(E1000_LED_ON, &adapter->led_status))
 		adapter->hw.mac.ops.led_off(&adapter->hw);
 	else
 		adapter->hw.mac.ops.led_on(&adapter->hw);
+}
+
+static void e1000_led_blink_callback(unsigned long data)
+{
+	struct e1000_adapter *adapter = (struct e1000_adapter *) data;
 
+	schedule_work(&adapter->led_blink_task);
 	mod_timer(&adapter->blink_timer, jiffies + E1000_ID_INTERVAL);
 }
 
@@ -1807,7 +1814,9 @@ static int e1000_phys_id(struct net_device *netdev, u32 data)
 		data = INT_MAX;
 
 	if ((hw->phy.type == e1000_phy_ife) ||
+	    (hw->mac.type == e1000_pchlan) ||
 	    (hw->mac.type == e1000_82574)) {
+		INIT_WORK(&adapter->led_blink_task, e1000e_led_blink_task);
 		if (!adapter->blink_timer.function) {
 			init_timer(&adapter->blink_timer);
 			adapter->blink_timer.function =

drivers/net/e1000e/hw.h

@@ -193,7 +193,11 @@ enum e1e_registers {
 	E1000_RXCSUM   = 0x05000, /* Rx Checksum Control - RW */
 	E1000_RFCTL    = 0x05008, /* Receive Filter Control */
 	E1000_MTA      = 0x05200, /* Multicast Table Array - RW Array */
-	E1000_RA       = 0x05400, /* Receive Address - RW Array */
+	E1000_RAL_BASE = 0x05400, /* Receive Address Low - RW */
+#define E1000_RAL(_n)   (E1000_RAL_BASE + ((_n) * 8))
+#define E1000_RA        (E1000_RAL(0))
+	E1000_RAH_BASE = 0x05404, /* Receive Address High - RW */
+#define E1000_RAH(_n)   (E1000_RAH_BASE + ((_n) * 8))
 	E1000_VFTA     = 0x05600, /* VLAN Filter Table Array - RW Array */
 	E1000_WUC      = 0x05800, /* Wakeup Control - RW */
 	E1000_WUFC     = 0x05808, /* Wakeup Filter Control - RW */
@@ -368,6 +372,10 @@ enum e1e_registers {
 #define E1000_DEV_ID_ICH10_R_BM_V		0x10CE
 #define E1000_DEV_ID_ICH10_D_BM_LM		0x10DE
 #define E1000_DEV_ID_ICH10_D_BM_LF		0x10DF
+#define E1000_DEV_ID_PCH_M_HV_LM		0x10EA
+#define E1000_DEV_ID_PCH_M_HV_LC		0x10EB
+#define E1000_DEV_ID_PCH_D_HV_DM		0x10EF
+#define E1000_DEV_ID_PCH_D_HV_DC		0x10F0
 
 #define E1000_REVISION_4 4
 
@@ -383,6 +391,7 @@ enum e1000_mac_type {
 	e1000_ich8lan,
 	e1000_ich9lan,
 	e1000_ich10lan,
+	e1000_pchlan,
 };
 
 enum e1000_media_type {
@@ -417,6 +426,8 @@ enum e1000_phy_type {
 	e1000_phy_igp_3,
 	e1000_phy_ife,
 	e1000_phy_bm,
+	e1000_phy_82578,
+	e1000_phy_82577,
 };
 
 enum e1000_bus_width {
@@ -720,6 +731,7 @@ struct e1000_host_mng_command_info {
 
 /* Function pointers and static data for the MAC. */
 struct e1000_mac_operations {
+	s32  (*id_led_init)(struct e1000_hw *);
 	bool (*check_mng_mode)(struct e1000_hw *);
 	s32  (*check_for_link)(struct e1000_hw *);
 	s32  (*cleanup_led)(struct e1000_hw *);
@@ -733,11 +745,13 @@ struct e1000_mac_operations {
 	s32  (*init_hw)(struct e1000_hw *);
 	s32  (*setup_link)(struct e1000_hw *);
 	s32  (*setup_physical_interface)(struct e1000_hw *);
+	s32  (*setup_led)(struct e1000_hw *);
 };
 
 /* Function pointers for the PHY. */
 struct e1000_phy_operations {
 	s32  (*acquire_phy)(struct e1000_hw *);
+	s32  (*check_polarity)(struct e1000_hw *);
 	s32  (*check_reset_block)(struct e1000_hw *);
 	s32  (*commit_phy)(struct e1000_hw *);
 	s32  (*force_speed_duplex)(struct e1000_hw *);

drivers/net/e1000e/lib.c

@@ -378,6 +378,12 @@ s32 e1000e_check_for_copper_link(struct e1000_hw *hw)
 
 	mac->get_link_status = 0;
 
+	if (hw->phy.type == e1000_phy_82578) {
+		ret_val = e1000_link_stall_workaround_hv(hw);
+		if (ret_val)
+			return ret_val;
+	}
+
 	/*
 	 * Check if there was DownShift, must be checked
 	 * immediately after link-up
@@ -1405,6 +1411,38 @@ s32 e1000e_id_led_init(struct e1000_hw *hw)
 	return 0;
 }
 
+/**
+ *  e1000e_setup_led_generic - Configures SW controllable LED
+ *  @hw: pointer to the HW structure
+ *
+ *  This prepares the SW controllable LED for use and saves the current state
+ *  of the LED so it can be later restored.
+ **/
+s32 e1000e_setup_led_generic(struct e1000_hw *hw)
+{
+	u32 ledctl;
+
+	if (hw->mac.ops.setup_led != e1000e_setup_led_generic) {
+		return -E1000_ERR_CONFIG;
+	}
+
+	if (hw->phy.media_type == e1000_media_type_fiber) {
+		ledctl = er32(LEDCTL);
+		hw->mac.ledctl_default = ledctl;
+		/* Turn off LED0 */
+		ledctl &= ~(E1000_LEDCTL_LED0_IVRT |
+		            E1000_LEDCTL_LED0_BLINK |
+		            E1000_LEDCTL_LED0_MODE_MASK);
+		ledctl |= (E1000_LEDCTL_MODE_LED_OFF <<
+		           E1000_LEDCTL_LED0_MODE_SHIFT);
+		ew32(LEDCTL, ledctl);
+	} else if (hw->phy.media_type == e1000_media_type_copper) {
+		ew32(LEDCTL, hw->mac.ledctl_mode1);
+	}
+
+	return 0;
+}
+
 /**
  *  e1000e_cleanup_led_generic - Set LED config to default operation
  *  @hw: pointer to the HW structure

drivers/net/e1000e/netdev.c

@@ -62,6 +62,7 @@ static const struct e1000_info *e1000_info_tbl[] = {
 	[board_ich8lan]		= &e1000_ich8_info,
 	[board_ich9lan]		= &e1000_ich9_info,
 	[board_ich10lan]	= &e1000_ich10_info,
+	[board_pchlan]		= &e1000_pch_info,
 };
 
 #ifdef DEBUG
@@ -2308,6 +2309,23 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 	if (adapter->flags2 & FLAG2_CRC_STRIPPING)
 		rctl |= E1000_RCTL_SECRC;
 
+	/* Workaround Si errata on 82577 PHY - configure IPG for jumbos */
+	if ((hw->phy.type == e1000_phy_82577) && (rctl & E1000_RCTL_LPE)) {
+		u16 phy_data;
+
+		e1e_rphy(hw, PHY_REG(770, 26), &phy_data);
+		phy_data &= 0xfff8;
+		phy_data |= (1 << 2);
+		e1e_wphy(hw, PHY_REG(770, 26), phy_data);
+
+		e1e_rphy(hw, 22, &phy_data);
+		phy_data &= 0x0fff;
+		phy_data |= (1 << 14);
+		e1e_wphy(hw, 0x10, 0x2823);
+		e1e_wphy(hw, 0x11, 0x0003);
+		e1e_wphy(hw, 22, phy_data);
+	}
+
 	/* Setup buffer sizes */
 	rctl &= ~E1000_RCTL_SZ_4096;
 	rctl |= E1000_RCTL_BSEX;
@@ -2789,6 +2807,8 @@ void e1000e_reset(struct e1000_adapter *adapter)
 		e1000_get_hw_control(adapter);
 
 	ew32(WUC, 0);
+	if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP)
+		e1e_wphy(&adapter->hw, BM_WUC, 0);
 
 	if (mac->ops.init_hw(hw))
 		e_err("Hardware Error\n");
@@ -3269,6 +3289,7 @@ void e1000e_update_stats(struct e1000_adapter *adapter)
 {
 	struct e1000_hw *hw = &adapter->hw;
 	struct pci_dev *pdev = adapter->pdev;
+	u16 phy_data;
 
 	/*
 	 * Prevent stats update while adapter is being reset, or if the pci
@@ -3288,11 +3309,34 @@ void e1000e_update_stats(struct e1000_adapter *adapter)
 	adapter->stats.roc += er32(ROC);
 
 	adapter->stats.mpc += er32(MPC);
+	if ((hw->phy.type == e1000_phy_82578) ||
+	    (hw->phy.type == e1000_phy_82577)) {
+		e1e_rphy(hw, HV_SCC_UPPER, &phy_data);
+		e1e_rphy(hw, HV_SCC_LOWER, &phy_data);
+		adapter->stats.scc += phy_data;
+
+		e1e_rphy(hw, HV_ECOL_UPPER, &phy_data);
+		e1e_rphy(hw, HV_ECOL_LOWER, &phy_data);
+		adapter->stats.ecol += phy_data;
+
+		e1e_rphy(hw, HV_MCC_UPPER, &phy_data);
+		e1e_rphy(hw, HV_MCC_LOWER, &phy_data);
+		adapter->stats.mcc += phy_data;
+
+		e1e_rphy(hw, HV_LATECOL_UPPER, &phy_data);
+		e1e_rphy(hw, HV_LATECOL_LOWER, &phy_data);
+		adapter->stats.latecol += phy_data;
+
+		e1e_rphy(hw, HV_DC_UPPER, &phy_data);
+		e1e_rphy(hw, HV_DC_LOWER, &phy_data);
+		adapter->stats.dc += phy_data;
+	} else {
 		adapter->stats.scc += er32(SCC);
 		adapter->stats.ecol += er32(ECOL);
 		adapter->stats.mcc += er32(MCC);
 		adapter->stats.latecol += er32(LATECOL);
 		adapter->stats.dc += er32(DC);
+	}
 	adapter->stats.xonrxc += er32(XONRXC);
 	adapter->stats.xontxc += er32(XONTXC);
 	adapter->stats.xoffrxc += er32(XOFFRXC);
@@ -3310,13 +3354,28 @@ void e1000e_update_stats(struct e1000_adapter *adapter)
 
 	hw->mac.tx_packet_delta = er32(TPT);
 	adapter->stats.tpt += hw->mac.tx_packet_delta;
+	if ((hw->phy.type == e1000_phy_82578) ||
+	    (hw->phy.type == e1000_phy_82577)) {
+		e1e_rphy(hw, HV_COLC_UPPER, &phy_data);
+		e1e_rphy(hw, HV_COLC_LOWER, &phy_data);
+		hw->mac.collision_delta = phy_data;
+	} else {
 		hw->mac.collision_delta = er32(COLC);
+	}
 	adapter->stats.colc += hw->mac.collision_delta;
 
 	adapter->stats.algnerrc += er32(ALGNERRC);
 	adapter->stats.rxerrc += er32(RXERRC);
-	if ((hw->mac.type != e1000_82574) && (hw->mac.type != e1000_82583))
+	if ((hw->phy.type == e1000_phy_82578) ||
+	    (hw->phy.type == e1000_phy_82577)) {
+		e1e_rphy(hw, HV_TNCRS_UPPER, &phy_data);
+		e1e_rphy(hw, HV_TNCRS_LOWER, &phy_data);
+		adapter->stats.tncrs += phy_data;
+	} else {
+		if ((hw->mac.type != e1000_82574) &&
+		    (hw->mac.type != e1000_82583))
 			adapter->stats.tncrs += er32(TNCRS);
+	}
 	adapter->stats.cexterr += er32(CEXTERR);
 	adapter->stats.tsctc += er32(TSCTC);
 	adapter->stats.tsctfc += er32(TSCTFC);
@@ -4342,6 +4401,81 @@ static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
 	}
 }
 
+static int e1000_init_phy_wakeup(struct e1000_adapter *adapter, u32 wufc)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	u32 i, mac_reg;
+	u16 phy_reg;
+	int retval = 0;
+
+	/* copy MAC RARs to PHY RARs */
+	for (i = 0; i < adapter->hw.mac.rar_entry_count; i++) {
+		mac_reg = er32(RAL(i));
+		e1e_wphy(hw, BM_RAR_L(i), (u16)(mac_reg & 0xFFFF));
+		e1e_wphy(hw, BM_RAR_M(i), (u16)((mac_reg >> 16) & 0xFFFF));
+		mac_reg = er32(RAH(i));
+		e1e_wphy(hw, BM_RAR_H(i), (u16)(mac_reg & 0xFFFF));
+		e1e_wphy(hw, BM_RAR_CTRL(i), (u16)((mac_reg >> 16) & 0xFFFF));
+	}
+
+	/* copy MAC MTA to PHY MTA */
+	for (i = 0; i < adapter->hw.mac.mta_reg_count; i++) {
+		mac_reg = E1000_READ_REG_ARRAY(hw, E1000_MTA, i);
+		e1e_wphy(hw, BM_MTA(i), (u16)(mac_reg & 0xFFFF));
+		e1e_wphy(hw, BM_MTA(i) + 1, (u16)((mac_reg >> 16) & 0xFFFF));
+	}
+
+	/* configure PHY Rx Control register */
+	e1e_rphy(&adapter->hw, BM_RCTL, &phy_reg);
+	mac_reg = er32(RCTL);
+	if (mac_reg & E1000_RCTL_UPE)
+		phy_reg |= BM_RCTL_UPE;
+	if (mac_reg & E1000_RCTL_MPE)
+		phy_reg |= BM_RCTL_MPE;
+	phy_reg &= ~(BM_RCTL_MO_MASK);
+	if (mac_reg & E1000_RCTL_MO_3)
+		phy_reg |= (((mac_reg & E1000_RCTL_MO_3) >> E1000_RCTL_MO_SHIFT)
+				<< BM_RCTL_MO_SHIFT);
+	if (mac_reg & E1000_RCTL_BAM)
+		phy_reg |= BM_RCTL_BAM;
+	if (mac_reg & E1000_RCTL_PMCF)
+		phy_reg |= BM_RCTL_PMCF;
+	mac_reg = er32(CTRL);
+	if (mac_reg & E1000_CTRL_RFCE)
+		phy_reg |= BM_RCTL_RFCE;
+	e1e_wphy(&adapter->hw, BM_RCTL, phy_reg);
+
+	/* enable PHY wakeup in MAC register */
+	ew32(WUFC, wufc);
+	ew32(WUC, E1000_WUC_PHY_WAKE | E1000_WUC_PME_EN);
+
+	/* configure and enable PHY wakeup in PHY registers */
+	e1e_wphy(&adapter->hw, BM_WUFC, wufc);
+	e1e_wphy(&adapter->hw, BM_WUC, E1000_WUC_PME_EN);
+
+	/* activate PHY wakeup */
+	retval = hw->phy.ops.acquire_phy(hw);
+	if (retval) {
+		e_err("Could not acquire PHY\n");
+		return retval;
+	}
+	e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+	                         (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
+	retval = e1000e_read_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, &phy_reg);
+	if (retval) {
+		e_err("Could not read PHY page 769\n");
+		goto out;
+	}
+	phy_reg |= BM_WUC_ENABLE_BIT | BM_WUC_HOST_WU_BIT;
+	retval = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
+	if (retval)
+		e_err("Could not set PHY Host Wakeup bit\n");
+out:
+	hw->phy.ops.release_phy(hw);
+
+	return retval;
+}
+
 static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
 {
 	struct net_device *netdev = pci_get_drvdata(pdev);
@@ -4384,8 +4518,9 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
 		#define E1000_CTRL_ADVD3WUC 0x00100000
 		/* phy power management enable */
 		#define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000
-		ctrl |= E1000_CTRL_ADVD3WUC |
-			E1000_CTRL_EN_PHY_PWR_MGMT;
+		ctrl |= E1000_CTRL_ADVD3WUC;
+		if (!(adapter->flags2 & FLAG2_HAS_PHY_WAKEUP))
+			ctrl |= E1000_CTRL_EN_PHY_PWR_MGMT;
 		ew32(CTRL, ctrl);
 
 		if (adapter->hw.phy.media_type == e1000_media_type_fiber ||
@@ -4403,8 +4538,17 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
 		/* Allow time for pending master requests to run */
 		e1000e_disable_pcie_master(&adapter->hw);
 
-		ew32(WUC, E1000_WUC_PME_EN);
+		if ((adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) &&
+		    !(hw->mac.ops.check_mng_mode(hw))) {
+			/* enable wakeup by the PHY */
+			retval = e1000_init_phy_wakeup(adapter, wufc);
+			if (retval)
+				return retval;
+		} else {
+			/* enable wakeup by the MAC */
 			ew32(WUFC, wufc);
+			ew32(WUC, E1000_WUC_PME_EN);
+		}
 	} else {
 		ew32(WUC, 0);
 		ew32(WUFC, 0);
@@ -4547,8 +4691,37 @@ static int e1000_resume(struct pci_dev *pdev)
 	}
 
 	e1000e_power_up_phy(adapter);
-	e1000e_reset(adapter);
+
+	/* report the system wakeup cause from S3/S4 */
+	if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) {
+		u16 phy_data;
+
+		e1e_rphy(&adapter->hw, BM_WUS, &phy_data);
+		if (phy_data) {
+			e_info("PHY Wakeup cause - %s\n",
+				phy_data & E1000_WUS_EX ? "Unicast Packet" :
+				phy_data & E1000_WUS_MC ? "Multicast Packet" :
+				phy_data & E1000_WUS_BC ? "Broadcast Packet" :
+				phy_data & E1000_WUS_MAG ? "Magic Packet" :
+				phy_data & E1000_WUS_LNKC ? "Link Status "
+				" Change" : "other");
+		}
+		e1e_wphy(&adapter->hw, BM_WUS, ~0);
+	} else {
+		u32 wus = er32(WUS);
+		if (wus) {
+			e_info("MAC Wakeup cause - %s\n",
+				wus & E1000_WUS_EX ? "Unicast Packet" :
+				wus & E1000_WUS_MC ? "Multicast Packet" :
+				wus & E1000_WUS_BC ? "Broadcast Packet" :
+				wus & E1000_WUS_MAG ? "Magic Packet" :
+				wus & E1000_WUS_LNKC ? "Link Status Change" :
+				"other");
+		}
 		ew32(WUS, ~0);
+	}
+
+	e1000e_reset(adapter);
 
 	e1000_init_manageability(adapter);
 
@@ -4994,6 +5167,8 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 		/* APME bit in EEPROM is mapped to WUC.APME */
 		eeprom_data = er32(WUC);
 		eeprom_apme_mask = E1000_WUC_APME;
+		if (eeprom_data & E1000_WUC_PHY_WAKE)
+			adapter->flags2 |= FLAG2_HAS_PHY_WAKEUP;
 	} else if (adapter->flags & FLAG_APME_IN_CTRL3) {
 		if (adapter->flags & FLAG_APME_CHECK_PORT_B &&
 		    (adapter->hw.bus.func == 1))
@@ -5195,6 +5370,11 @@ static struct pci_device_id e1000_pci_tbl[] = {
 	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LM), board_ich10lan },
 	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LF), board_ich10lan },
 
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LM), board_pchlan },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LC), board_pchlan },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DM), board_pchlan },
+	{ PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DC), board_pchlan },
+
 	{ }	/* terminate list */
 };
 MODULE_DEVICE_TABLE(pci, e1000_pci_tbl);