Merge branch 'bcmgenet'

Florian Fainelli says:

====================
Support for the Broadcom GENET driver

This patchset adds support for the Broadcom GENET Gigabit Ethernet MAC
controller. This controller is found on the Broadcom BCM7xxx Set Top Box
System-on-a-chips.

Changes since v4:
- add dependency on CONFIG_OF

Changes since v3:
- fixed Kconfig dependency on FIXED_PHY

Changes since v2:
- dropped the patch that adds an "internal" phy-mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt

+* Broadcom BCM7xxx Ethernet Controller (GENET)
+
+Required properties:
+- compatible: should contain one of "brcm,genet-v1", "brcm,genet-v2",
+  "brcm,genet-v3", "brcm,genet-v4".
+- reg: address and length of the register set for the device
+- interrupts: must be two cells, the first cell is the general purpose
+  interrupt line, while the second cell is the interrupt for the ring
+  RX and TX queues operating in ring mode
+- phy-mode: String, operation mode of the PHY interface. Supported values are
+  "mii", "rgmii", "rgmii-txid", "rev-mii", "moca". Analogous to ePAPR
+  "phy-connection-type" values
+- address-cells: should be 1
+- size-cells: should be 1
+
+Optional properties:
+- clocks: When provided, must be two cells, first one is the main GENET clock
+  and the second cell is the Genet Wake-on-LAN clock.
+
+- phy-handle: A phandle to a phy node defining the PHY address (as the reg
+  property, a single integer), used to describe configurations where a PHY
+  (internal or external) is used.
+
+- fixed-link: When the GENET interface is connected to a MoCA hardware block or
+  when operating in a RGMII to RGMII type of connection, or when the MDIO bus is
+  voluntarily disabled, this property should be used to describe the "fixed link".
+  See Documentation/devicetree/bindings/net/fsl-tsec-phy.txt for information on
+  the property specifics
+
+Required child nodes:
+
+- mdio bus node: this node should always be present regarless of the PHY
+  configuration of the GENET instance
+
+MDIO bus node required properties:
+
+- compatible: should contain one of "brcm,genet-mdio-v1", "brcm,genet-mdio-v2"
+  "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", the version has to match the
+  parent node compatible property (e.g: brcm,genet-v4 pairs with
+  brcm,genet-mdio-v4)
+- reg: address and length relative to the parent node base register address
+- address-cells: address cell for MDIO bus addressing, should be 1
+- size-cells: size of the cells for MDIO bus addressing, should be 0
+
+Ethernet PHY node properties:
+
+See Documentation/devicetree/bindings/net/phy.txt for the list of required and
+optional properties.
+
+Internal Gigabit PHY example:
+
+ethernet@f0b60000 {
+	phy-mode = "internal";
+	phy-handle = <&phy1>;
+	mac-address = [ 00 10 18 36 23 1a ];
+	compatible = "brcm,genet-v4";
+	#address-cells = <0x1>;
+	#size-cells = <0x1>;
+	reg = <0xf0b60000 0xfc4c>;
+	interrupts = <0x0 0x14 0x0>, <0x0 0x15 0x0>;
+
+	mdio@e14 {
+		compatible = "brcm,genet-mdio-v4";
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+		reg = <0xe14 0x8>;
+
+		phy1: ethernet-phy@1 {
+			max-speed = <1000>;
+			reg = <0x1>;
+			compatible = "brcm,28nm-gphy", "ethernet-phy-ieee802.3-c22";
+		};
+	};
+};
+
+MoCA interface / MAC to MAC example:
+
+ethernet@f0b80000 {
+	phy-mode = "moca";
+	fixed-link = <1 0 1000 0 0>;
+	mac-address = [ 00 10 18 36 24 1a ];
+	compatible = "brcm,genet-v4";
+	#address-cells = <0x1>;
+	#size-cells = <0x1>;
+	reg = <0xf0b80000 0xfc4c>;
+	interrupts = <0x0 0x16 0x0>, <0x0 0x17 0x0>;
+
+	mdio@e14 {
+		compatible = "brcm,genet-mdio-v4";
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+		reg = <0xe14 0x8>;
+	};
+};
+
+
+External MDIO-connected Gigabit PHY/switch:
+
+ethernet@f0ba0000 {
+	phy-mode = "rgmii";
+	phy-handle = <&phy0>;
+	mac-address = [ 00 10 18 36 26 1a ];
+	compatible = "brcm,genet-v4";
+	#address-cells = <0x1>;
+	#size-cells = <0x1>;
+	reg = <0xf0ba0000 0xfc4c>;
+	interrupts = <0x0 0x18 0x0>, <0x0 0x19 0x0>;
+
+	mdio@0e14 {
+		compatible = "brcm,genet-mdio-v4";
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+		reg = <0xe14 0x8>;
+
+		phy0: ethernet-phy@0 {
+			max-speed = <1000>;
+			reg = <0x0>;
+			compatible = "brcm,bcm53125", "ethernet-phy-ieee802.3-c22";
+		};
+	};
+};

MAINTAINERS

@@ -1845,6 +1845,12 @@ L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/ethernet/broadcom/b44.*
 
+BROADCOM GENET ETHERNET DRIVER
+M:	Florian Fainelli <f.fainelli@gmail.com>
+L:	netdev@vger.kernel.org
+S:	Supported
+F:	drivers/net/ethernet/broadcom/genet/
+
 BROADCOM BNX2 GIGABIT ETHERNET DRIVER
 M:	Michael Chan <mchan@broadcom.com>
 L:	netdev@vger.kernel.org

drivers/net/ethernet/broadcom/Kconfig

@@ -60,6 +60,17 @@ config BCM63XX_ENET
 	  This driver supports the ethernet MACs in the Broadcom 63xx
 	  MIPS chipset family (BCM63XX).
 
+config BCMGENET
+	tristate "Broadcom GENET internal MAC support"
+	depends on OF
+	select MII
+	select PHYLIB
+	select FIXED_PHY if BCMGENET=y
+	select BCM7XXX_PHY
+	help
+	  This driver supports the built-in Ethernet MACs found in the
+	  Broadcom BCM7xxx Set Top Box family chipset.
+
 config BNX2
 	tristate "Broadcom NetXtremeII support"
 	depends on PCI

drivers/net/ethernet/broadcom/Makefile

@@ -4,6 +4,7 @@
 
 obj-$(CONFIG_B44) += b44.o
 obj-$(CONFIG_BCM63XX_ENET) += bcm63xx_enet.o
+obj-$(CONFIG_BCMGENET) += genet/
 obj-$(CONFIG_BNX2) += bnx2.o
 obj-$(CONFIG_CNIC) += cnic.o
 obj-$(CONFIG_BNX2X) += bnx2x/

drivers/net/ethernet/broadcom/genet/Makefile

+obj-$(CONFIG_BCMGENET) += genet.o
+genet-objs := bcmgenet.o bcmmii.o

drivers/net/phy/Kconfig

@@ -71,6 +71,12 @@ config BCM63XX_PHY
 	---help---
 	  Currently supports the 6348 and 6358 PHYs.
 
+config BCM7XXX_PHY
+	tristate "Drivers for Broadcom 7xxx SOCs internal PHYs"
+	---help---
+	  Currently supports the BCM7366, BCM7439, BCM7445, and
+	  40nm and 65nm generation of BCM7xxx Set Top Box SoCs.
+
 config BCM87XX_PHY
 	tristate "Driver for Broadcom BCM8706 and BCM8727 PHYs"
 	help

drivers/net/phy/Makefile

@@ -12,6 +12,7 @@ obj-$(CONFIG_SMSC_PHY)		+= smsc.o
 obj-$(CONFIG_VITESSE_PHY)	+= vitesse.o
 obj-$(CONFIG_BROADCOM_PHY)	+= broadcom.o
 obj-$(CONFIG_BCM63XX_PHY)	+= bcm63xx.o
+obj-$(CONFIG_BCM7XXX_PHY)	+= bcm7xxx.o
 obj-$(CONFIG_BCM87XX_PHY)	+= bcm87xx.o
 obj-$(CONFIG_ICPLUS_PHY)	+= icplus.o
 obj-$(CONFIG_REALTEK_PHY)	+= realtek.o

drivers/net/phy/bcm7xxx.c

+/*
+ * Broadcom BCM7xxx internal transceivers support.
+ *
+ * Copyright (C) 2014, Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/phy.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/brcmphy.h>
+
+/* Broadcom BCM7xxx internal PHY registers */
+#define MII_BCM7XXX_CHANNEL_WIDTH	0x2000
+
+/* 40nm only register definitions */
+#define MII_BCM7XXX_100TX_AUX_CTL	0x10
+#define MII_BCM7XXX_100TX_FALSE_CAR	0x13
+#define MII_BCM7XXX_100TX_DISC		0x14
+#define MII_BCM7XXX_AUX_MODE		0x1d
+#define  MII_BCM7XX_64CLK_MDIO		BIT(12)
+#define MII_BCM7XXX_CORE_BASE1E		0x1e
+#define MII_BCM7XXX_TEST		0x1f
+#define  MII_BCM7XXX_SHD_MODE_2		BIT(2)
+
+static int bcm7445_config_init(struct phy_device *phydev)
+{
+	int ret;
+	const struct bcm7445_regs {
+		int reg;
+		u16 value;
+	} bcm7445_regs_cfg[] = {
+		/* increases ADC latency by 24ns */
+		{ MII_BCM54XX_EXP_SEL, 0x0038 },
+		{ MII_BCM54XX_EXP_DATA, 0xAB95 },
+		/* increases internal 1V LDO voltage by 5% */
+		{ MII_BCM54XX_EXP_SEL, 0x2038 },
+		{ MII_BCM54XX_EXP_DATA, 0xBB22 },
+		/* reduce RX low pass filter corner frequency */
+		{ MII_BCM54XX_EXP_SEL, 0x6038 },
+		{ MII_BCM54XX_EXP_DATA, 0xFFC5 },
+		/* reduce RX high pass filter corner frequency */
+		{ MII_BCM54XX_EXP_SEL, 0x003a },
+		{ MII_BCM54XX_EXP_DATA, 0x2002 },
+	};
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(bcm7445_regs_cfg); i++) {
+		ret = phy_write(phydev,
+				bcm7445_regs_cfg[i].reg,
+				bcm7445_regs_cfg[i].value);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static void phy_write_exp(struct phy_device *phydev,
+					u16 reg, u16 value)
+{
+	phy_write(phydev, MII_BCM54XX_EXP_SEL, MII_BCM54XX_EXP_SEL_ER | reg);
+	phy_write(phydev, MII_BCM54XX_EXP_DATA, value);
+}
+
+static void phy_write_misc(struct phy_device *phydev,
+					u16 reg, u16 chl, u16 value)
+{
+	int tmp;
+
+	phy_write(phydev, MII_BCM54XX_AUX_CTL, MII_BCM54XX_AUXCTL_SHDWSEL_MISC);
+
+	tmp = phy_read(phydev, MII_BCM54XX_AUX_CTL);
+	tmp |= MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA;
+	phy_write(phydev, MII_BCM54XX_AUX_CTL, tmp);
+
+	tmp = (chl * MII_BCM7XXX_CHANNEL_WIDTH) | reg;
+	phy_write(phydev, MII_BCM54XX_EXP_SEL, tmp);
+
+	phy_write(phydev, MII_BCM54XX_EXP_DATA, value);
+}
+
+static int bcm7xxx_28nm_afe_config_init(struct phy_device *phydev)
+{
+	/* write AFE_RXCONFIG_0 */
+	phy_write_misc(phydev, 0x38, 0x0000, 0xeb19);
+
+	/* write AFE_RXCONFIG_1 */
+	phy_write_misc(phydev, 0x38, 0x0001, 0x9a3f);
+
+	/* write AFE_RX_LP_COUNTER */
+	phy_write_misc(phydev, 0x38, 0x0003, 0x7fc7);
+
+	/* write AFE_HPF_TRIM_OTHERS */
+	phy_write_misc(phydev, 0x3A, 0x0000, 0x000b);
+
+	/* write AFTE_TX_CONFIG */
+	phy_write_misc(phydev, 0x39, 0x0000, 0x0800);
+
+	/* Increase VCO range to prevent unlocking problem of PLL at low
+	 * temp
+	 */
+	phy_write_misc(phydev, 0x0032, 0x0001, 0x0048);
+
+	/* Change Ki to 011 */
+	phy_write_misc(phydev, 0x0032, 0x0002, 0x021b);
+
+	/* Disable loading of TVCO buffer to bandgap, set bandgap trim
+	 * to 111
+	 */
+	phy_write_misc(phydev, 0x0033, 0x0000, 0x0e20);
+
+	/* Adjust bias current trim by -3 */
+	phy_write_misc(phydev, 0x000a, 0x0000, 0x690b);
+
+	/* Switch to CORE_BASE1E */
+	phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0xd);
+
+	/* Reset R_CAL/RC_CAL Engine */
+	phy_write_exp(phydev, 0x00b0, 0x0010);
+
+	/* Disable Reset R_CAL/RC_CAL Engine */
+	phy_write_exp(phydev, 0x00b0, 0x0000);
+
+	return 0;
+}
+
+static int bcm7xxx_28nm_config_init(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = bcm7445_config_init(phydev);
+	if (ret)
+		return ret;
+
+	return bcm7xxx_28nm_afe_config_init(phydev);
+}
+
+static int phy_set_clr_bits(struct phy_device *dev, int location,
+					int set_mask, int clr_mask)
+{
+	int v, ret;
+
+	v = phy_read(dev, location);
+	if (v < 0)
+		return v;
+
+	v &= ~clr_mask;
+	v |= set_mask;
+
+	ret = phy_write(dev, location, v);
+	if (ret < 0)
+		return ret;
+
+	return v;
+}
+
+static int bcm7xxx_config_init(struct phy_device *phydev)
+{
+	int ret;
+
+	/* Enable 64 clock MDIO */
+	phy_write(phydev, MII_BCM7XXX_AUX_MODE, MII_BCM7XX_64CLK_MDIO);
+	phy_read(phydev, MII_BCM7XXX_AUX_MODE);
+
+	/* Workaround only required for 100Mbits/sec */
+	if (!(phydev->dev_flags & PHY_BRCM_100MBPS_WAR))
+		return 0;
+
+	/* set shadow mode 2 */
+	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
+			MII_BCM7XXX_SHD_MODE_2, MII_BCM7XXX_SHD_MODE_2);
+	if (ret < 0)
+		return ret;
+
+	/* set iddq_clkbias */
+	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0F00);
+	udelay(10);
+
+	/* reset iddq_clkbias */
+	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0C00);
+
+	phy_write(phydev, MII_BCM7XXX_100TX_FALSE_CAR, 0x7555);
+
+	/* reset shadow mode 2 */
+	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, MII_BCM7XXX_SHD_MODE_2, 0);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+/* Workaround for putting the PHY in IDDQ mode, required
+ * for all BCM7XXX PHYs
+ */
+static int bcm7xxx_suspend(struct phy_device *phydev)
+{
+	int ret;
+	const struct bcm7xxx_regs {
+		int reg;
+		u16 value;
+	} bcm7xxx_suspend_cfg[] = {
+		{ MII_BCM7XXX_TEST, 0x008b },
+		{ MII_BCM7XXX_100TX_AUX_CTL, 0x01c0 },
+		{ MII_BCM7XXX_100TX_DISC, 0x7000 },
+		{ MII_BCM7XXX_TEST, 0x000f },
+		{ MII_BCM7XXX_100TX_AUX_CTL, 0x20d0 },
+		{ MII_BCM7XXX_TEST, 0x000b },
+	};
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(bcm7xxx_suspend_cfg); i++) {
+		ret = phy_write(phydev,
+				bcm7xxx_suspend_cfg[i].reg,
+				bcm7xxx_suspend_cfg[i].value);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int bcm7xxx_dummy_config_init(struct phy_device *phydev)
+{
+	return 0;
+}
+
+static struct phy_driver bcm7xxx_driver[] = {
+{
+	.phy_id		= PHY_ID_BCM7366,
+	.phy_id_mask	= 0xfffffff0,
+	.name		= "Broadcom BCM7366",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_28nm_afe_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_28nm_afe_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.phy_id		= PHY_ID_BCM7439,
+	.phy_id_mask	= 0xfffffff0,
+	.name		= "Broadcom BCM7439",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_28nm_afe_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_28nm_afe_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.phy_id		= PHY_ID_BCM7445,
+	.phy_id_mask	= 0xfffffff0,
+	.name		= "Broadcom BCM7445",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_28nm_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_28nm_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.name		= "Broadcom BCM7XXX 28nm",
+	.phy_id		= PHY_ID_BCM7XXX_28,
+	.phy_id_mask	= PHY_BCM_OUI_MASK,
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_28nm_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_28nm_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.phy_id		= PHY_BCM_OUI_4,
+	.phy_id_mask	= 0xffff0000,
+	.name		= "Broadcom BCM7XXX 40nm",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.phy_id		= PHY_BCM_OUI_5,
+	.phy_id_mask	= 0xffffff00,
+	.name		= "Broadcom BCM7XXX 65nm",
+	.features	= PHY_BASIC_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_dummy_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_config_init,
+	.driver		= { .owner = THIS_MODULE },
+} };
+
+static struct mdio_device_id __maybe_unused bcm7xxx_tbl[] = {
+	{ PHY_ID_BCM7366, 0xfffffff0, },
+	{ PHY_ID_BCM7439, 0xfffffff0, },
+	{ PHY_ID_BCM7445, 0xfffffff0, },
+	{ PHY_ID_BCM7XXX_28, 0xfffffc00 },
+	{ PHY_BCM_OUI_4, 0xffff0000 },
+	{ PHY_BCM_OUI_5, 0xffffff00 },
+	{ }
+};
+
+static int __init bcm7xxx_phy_init(void)
+{
+	return phy_drivers_register(bcm7xxx_driver,
+			ARRAY_SIZE(bcm7xxx_driver));
+}
+
+static void __exit bcm7xxx_phy_exit(void)
+{
+	phy_drivers_unregister(bcm7xxx_driver,
+			ARRAY_SIZE(bcm7xxx_driver));
+}
+
+module_init(bcm7xxx_phy_init);
+module_exit(bcm7xxx_phy_exit);
+
+MODULE_DEVICE_TABLE(mdio, bcm7xxx_tbl);
+
+MODULE_DESCRIPTION("Broadcom BCM7xxx internal PHY driver");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Broadcom Corporation");

drivers/net/phy/broadcom.c

@@ -25,58 +25,6 @@
 #define BRCM_PHY_REV(phydev) \
 	((phydev)->drv->phy_id & ~((phydev)->drv->phy_id_mask))
 
-
-#define MII_BCM54XX_ECR		0x10	/* BCM54xx extended control register */
-#define MII_BCM54XX_ECR_IM	0x1000	/* Interrupt mask */
-#define MII_BCM54XX_ECR_IF	0x0800	/* Interrupt force */
-
-#define MII_BCM54XX_ESR		0x11	/* BCM54xx extended status register */
-#define MII_BCM54XX_ESR_IS	0x1000	/* Interrupt status */
-
-#define MII_BCM54XX_EXP_DATA	0x15	/* Expansion register data */
-#define MII_BCM54XX_EXP_SEL	0x17	/* Expansion register select */
-#define MII_BCM54XX_EXP_SEL_SSD	0x0e00	/* Secondary SerDes select */
-#define MII_BCM54XX_EXP_SEL_ER	0x0f00	/* Expansion register select */
-
-#define MII_BCM54XX_AUX_CTL	0x18	/* Auxiliary control register */
-#define MII_BCM54XX_ISR		0x1a	/* BCM54xx interrupt status register */
-#define MII_BCM54XX_IMR		0x1b	/* BCM54xx interrupt mask register */
-#define MII_BCM54XX_INT_CRCERR	0x0001	/* CRC error */
-#define MII_BCM54XX_INT_LINK	0x0002	/* Link status changed */
-#define MII_BCM54XX_INT_SPEED	0x0004	/* Link speed change */
-#define MII_BCM54XX_INT_DUPLEX	0x0008	/* Duplex mode changed */
-#define MII_BCM54XX_INT_LRS	0x0010	/* Local receiver status changed */
-#define MII_BCM54XX_INT_RRS	0x0020	/* Remote receiver status changed */
-#define MII_BCM54XX_INT_SSERR	0x0040	/* Scrambler synchronization error */
-#define MII_BCM54XX_INT_UHCD	0x0080	/* Unsupported HCD negotiated */
-#define MII_BCM54XX_INT_NHCD	0x0100	/* No HCD */
-#define MII_BCM54XX_INT_NHCDL	0x0200	/* No HCD link */
-#define MII_BCM54XX_INT_ANPR	0x0400	/* Auto-negotiation page received */
-#define MII_BCM54XX_INT_LC	0x0800	/* All counters below 128 */
-#define MII_BCM54XX_INT_HC	0x1000	/* Counter above 32768 */
-#define MII_BCM54XX_INT_MDIX	0x2000	/* MDIX status change */
-#define MII_BCM54XX_INT_PSERR	0x4000	/* Pair swap error */
-
-#define MII_BCM54XX_SHD		0x1c	/* 0x1c shadow registers */
-#define MII_BCM54XX_SHD_WRITE	0x8000
-#define MII_BCM54XX_SHD_VAL(x)	((x & 0x1f) << 10)
-#define MII_BCM54XX_SHD_DATA(x)	((x & 0x3ff) << 0)
-
-/*
- * AUXILIARY CONTROL SHADOW ACCESS REGISTERS.  (PHY REG 0x18)
- */
-#define MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL	0x0000
-#define MII_BCM54XX_AUXCTL_ACTL_TX_6DB		0x0400
-#define MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA	0x0800
-
-#define MII_BCM54XX_AUXCTL_MISC_WREN	0x8000
-#define MII_BCM54XX_AUXCTL_MISC_FORCE_AMDIX	0x0200
-#define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC	0x7000
-#define MII_BCM54XX_AUXCTL_SHDWSEL_MISC	0x0007
-
-#define MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL	0x0000
-
-
 /*
  * Broadcom LED source encodings.  These are used in BCM5461, BCM5481,
  * BCM5482, and possibly some others.

drivers/net/phy/phy.c

@@ -305,6 +305,9 @@ int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd)
 
 	ethtool_cmd_speed_set(cmd, phydev->speed);
 	cmd->duplex = phydev->duplex;
+	if (phydev->interface == PHY_INTERFACE_MODE_MOCA)
+		cmd->port = PORT_BNC;
+	else
 		cmd->port = PORT_MII;
 	cmd->phy_address = phydev->addr;
 	cmd->transceiver = phy_is_internal(phydev) ?

include/linux/brcmphy.h

@@ -13,10 +13,17 @@
 #define PHY_ID_BCM5461			0x002060c0
 #define PHY_ID_BCM57780			0x03625d90
 
+#define PHY_ID_BCM7366			0x600d8490
+#define PHY_ID_BCM7439			0x600d8480
+#define PHY_ID_BCM7445			0x600d8510
+#define PHY_ID_BCM7XXX_28		0x600d8400
+
 #define PHY_BCM_OUI_MASK		0xfffffc00
 #define PHY_BCM_OUI_1			0x00206000
 #define PHY_BCM_OUI_2			0x0143bc00
 #define PHY_BCM_OUI_3			0x03625c00
+#define PHY_BCM_OUI_4			0x600d0000
+#define PHY_BCM_OUI_5			0x03625e00
 
 
 #define PHY_BCM_FLAGS_MODE_COPPER	0x00000001
@@ -31,6 +38,59 @@
 #define PHY_BRCM_EXT_IBND_TX_ENABLE	0x00002000
 #define PHY_BRCM_CLEAR_RGMII_MODE	0x00004000
 #define PHY_BRCM_DIS_TXCRXC_NOENRGY	0x00008000
+/* Broadcom BCM7xxx specific workarounds */
+#define PHY_BRCM_100MBPS_WAR		0x00010000
 #define PHY_BCM_FLAGS_VALID		0x80000000
 
+/* Broadcom BCM54XX register definitions, common to most Broadcom PHYs */
+#define MII_BCM54XX_ECR		0x10	/* BCM54xx extended control register */
+#define MII_BCM54XX_ECR_IM	0x1000	/* Interrupt mask */
+#define MII_BCM54XX_ECR_IF	0x0800	/* Interrupt force */
+
+#define MII_BCM54XX_ESR		0x11	/* BCM54xx extended status register */
+#define MII_BCM54XX_ESR_IS	0x1000	/* Interrupt status */
+
+#define MII_BCM54XX_EXP_DATA	0x15	/* Expansion register data */
+#define MII_BCM54XX_EXP_SEL	0x17	/* Expansion register select */
+#define MII_BCM54XX_EXP_SEL_SSD	0x0e00	/* Secondary SerDes select */
+#define MII_BCM54XX_EXP_SEL_ER	0x0f00	/* Expansion register select */
+
+#define MII_BCM54XX_AUX_CTL	0x18	/* Auxiliary control register */
+#define MII_BCM54XX_ISR		0x1a	/* BCM54xx interrupt status register */
+#define MII_BCM54XX_IMR		0x1b	/* BCM54xx interrupt mask register */
+#define MII_BCM54XX_INT_CRCERR	0x0001	/* CRC error */
+#define MII_BCM54XX_INT_LINK	0x0002	/* Link status changed */
+#define MII_BCM54XX_INT_SPEED	0x0004	/* Link speed change */
+#define MII_BCM54XX_INT_DUPLEX	0x0008	/* Duplex mode changed */
+#define MII_BCM54XX_INT_LRS	0x0010	/* Local receiver status changed */
+#define MII_BCM54XX_INT_RRS	0x0020	/* Remote receiver status changed */
+#define MII_BCM54XX_INT_SSERR	0x0040	/* Scrambler synchronization error */
+#define MII_BCM54XX_INT_UHCD	0x0080	/* Unsupported HCD negotiated */
+#define MII_BCM54XX_INT_NHCD	0x0100	/* No HCD */
+#define MII_BCM54XX_INT_NHCDL	0x0200	/* No HCD link */
+#define MII_BCM54XX_INT_ANPR	0x0400	/* Auto-negotiation page received */
+#define MII_BCM54XX_INT_LC	0x0800	/* All counters below 128 */
+#define MII_BCM54XX_INT_HC	0x1000	/* Counter above 32768 */
+#define MII_BCM54XX_INT_MDIX	0x2000	/* MDIX status change */
+#define MII_BCM54XX_INT_PSERR	0x4000	/* Pair swap error */
+
+#define MII_BCM54XX_SHD		0x1c	/* 0x1c shadow registers */
+#define MII_BCM54XX_SHD_WRITE	0x8000
+#define MII_BCM54XX_SHD_VAL(x)	((x & 0x1f) << 10)
+#define MII_BCM54XX_SHD_DATA(x)	((x & 0x3ff) << 0)
+
+/*
+ * AUXILIARY CONTROL SHADOW ACCESS REGISTERS.  (PHY REG 0x18)
+ */
+#define MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL	0x0000
+#define MII_BCM54XX_AUXCTL_ACTL_TX_6DB		0x0400
+#define MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA	0x0800
+
+#define MII_BCM54XX_AUXCTL_MISC_WREN	0x8000
+#define MII_BCM54XX_AUXCTL_MISC_FORCE_AMDIX	0x0200
+#define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC	0x7000
+#define MII_BCM54XX_AUXCTL_SHDWSEL_MISC	0x0007
+
+#define MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL	0x0000
+
 #endif /* _LINUX_BRCMPHY_H */

include/linux/phy.h

@@ -74,6 +74,7 @@ typedef enum {
 	PHY_INTERFACE_MODE_RTBI,
 	PHY_INTERFACE_MODE_SMII,
 	PHY_INTERFACE_MODE_XGMII,
+	PHY_INTERFACE_MODE_MOCA,
 	PHY_INTERFACE_MODE_MAX,
 } phy_interface_t;
 
@@ -113,6 +114,8 @@ static inline const char *phy_modes(phy_interface_t interface)
 		return "smii";
 	case PHY_INTERFACE_MODE_XGMII:
 		return "xgmii";
+	case PHY_INTERFACE_MODE_MOCA:
+		return "moca";
 	default:
 		return "unknown";
 	}