Add support for Eukrea's MBIMX27

MBIMX27 is the evaluation board for CPUIMX27 and integrates : a
QVGA TFT, a SPI touchscreen controler, a SDCard connector wired to
SDHC1.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arch/arm/mach-mx2/Kconfig

@@ -67,6 +67,20 @@ config MACH_EUKREA_CPUIMX27_USESDHC2
 	  This adds support for the internal SDHC2 used on CPUIMX27 used
 	  for wifi or eMMC.
 
+choice
+	prompt "Baseboard"
+	depends on MACH_EUKREA_CPUIMX27
+	default MACH_EUKREA_MBIMX27_BASEBOARD
+
+config MACH_EUKREA_MBIMX27_BASEBOARD
+	prompt "Eukrea MBIMX27 development board"
+	bool
+	help
+	  This adds board specific devices that can be found on Eukrea's
+	  MBIMX27 evaluation board.
+
+endchoice
+
 config MACH_MX27_3DS
 	bool "MX27PDK platform"
 	depends on MACH_MX27

arch/arm/mach-mx2/Makefile

@@ -18,3 +18,4 @@ obj-$(CONFIG_MACH_PCM970_BASEBOARD) += pcm970-baseboard.o
 obj-$(CONFIG_MACH_MX27_3DS) += mx27pdk.o
 obj-$(CONFIG_MACH_MX27LITE) += mx27lite.o
 obj-$(CONFIG_MACH_EUKREA_CPUIMX27) += eukrea_cpuimx27.o
+obj-$(CONFIG_MACH_EUKREA_MBIMX27_BASEBOARD) += eukrea_mbimx27-baseboard.o

arch/arm/mach-mx2/eukrea_mbimx27-baseboard.c

+/*
+ * Copyright (C) 2009 Eric Benard - eric@eukrea.com
+ *
+ * Based on pcm970-baseboard.c which is :
+ * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#include <linux/gpio.h>
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+
+#include <asm/mach/arch.h>
+
+#include <mach/common.h>
+#include <mach/iomux.h>
+#include <mach/imxfb.h>
+#include <mach/hardware.h>
+#include <mach/mmc.h>
+#include <mach/imx-uart.h>
+
+#include "devices.h"
+
+static int eukrea_mbimx27_pins[] = {
+	/* UART2 */
+	PE3_PF_UART2_CTS,
+	PE4_PF_UART2_RTS,
+	PE6_PF_UART2_TXD,
+	PE7_PF_UART2_RXD,
+	/* UART3 */
+	PE8_PF_UART3_TXD,
+	PE9_PF_UART3_RXD,
+	PE10_PF_UART3_CTS,
+	PE11_PF_UART3_RTS,
+	/* UART4 */
+	PB26_AF_UART4_RTS,
+	PB28_AF_UART4_TXD,
+	PB29_AF_UART4_CTS,
+	PB31_AF_UART4_RXD,
+	/* SDHC1*/
+	PE18_PF_SD1_D0,
+	PE19_PF_SD1_D1,
+	PE20_PF_SD1_D2,
+	PE21_PF_SD1_D3,
+	PE22_PF_SD1_CMD,
+	PE23_PF_SD1_CLK,
+	/* display */
+	PA5_PF_LSCLK,
+	PA6_PF_LD0,
+	PA7_PF_LD1,
+	PA8_PF_LD2,
+	PA9_PF_LD3,
+	PA10_PF_LD4,
+	PA11_PF_LD5,
+	PA12_PF_LD6,
+	PA13_PF_LD7,
+	PA14_PF_LD8,
+	PA15_PF_LD9,
+	PA16_PF_LD10,
+	PA17_PF_LD11,
+	PA18_PF_LD12,
+	PA19_PF_LD13,
+	PA20_PF_LD14,
+	PA21_PF_LD15,
+	PA22_PF_LD16,
+	PA23_PF_LD17,
+	PA28_PF_HSYNC,
+	PA29_PF_VSYNC,
+	PA30_PF_CONTRAST,
+	PA31_PF_OE_ACD,
+	/* SPI1 */
+	PD28_PF_CSPI1_SS0,
+	PD29_PF_CSPI1_SCLK,
+	PD30_PF_CSPI1_MISO,
+	PD31_PF_CSPI1_MOSI,
+};
+
+static struct gpio_led gpio_leds[] = {
+	{
+		.name			= "led1",
+		.default_trigger	= "heartbeat",
+		.active_low		= 1,
+		.gpio			= GPIO_PORTF | 16,
+	},
+	{
+		.name			= "led2",
+		.default_trigger	= "none",
+		.active_low		= 1,
+		.gpio			= GPIO_PORTF | 19,
+	},
+	{
+		.name			= "backlight",
+		.default_trigger	= "backlight",
+		.active_low		= 0,
+		.gpio			= GPIO_PORTE | 5,
+	},
+};
+
+static struct gpio_led_platform_data gpio_led_info = {
+	.leds		= gpio_leds,
+	.num_leds	= ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device leds_gpio = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &gpio_led_info,
+	},
+};
+
+static struct imx_fb_videomode eukrea_mbimx27_modes[] = {
+	{
+		.mode = {
+			.name		= "CMO-QGVA",
+			.refresh	= 60,
+			.xres		= 320,
+			.yres		= 240,
+			.pixclock	= 156000,
+			.hsync_len	= 30,
+			.left_margin	= 38,
+			.right_margin	= 20,
+			.vsync_len	= 3,
+			.upper_margin	= 15,
+			.lower_margin	= 4,
+		},
+		.pcr		= 0xFAD08B80,
+		.bpp		= 16,
+	},
+};
+
+static struct imx_fb_platform_data eukrea_mbimx27_fb_data = {
+	.mode = eukrea_mbimx27_modes,
+	.num_modes = ARRAY_SIZE(eukrea_mbimx27_modes),
+
+	.pwmr		= 0x00A903FF,
+	.lscr1		= 0x00120300,
+	.dmacr		= 0x00040060,
+};
+
+static struct imxuart_platform_data uart_pdata[] = {
+	{
+		.flags = IMXUART_HAVE_RTSCTS,
+	},
+	{
+		.flags = IMXUART_HAVE_RTSCTS,
+	},
+};
+
+#if defined(CONFIG_TOUCHSCREEN_ADS7846)
+	|| defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+
+#define ADS7846_PENDOWN (GPIO_PORTD | 25)
+
+static void ads7846_dev_init(void)
+{
+	if (gpio_request(ADS7846_PENDOWN, "ADS7846 pendown") < 0) {
+		printk(KERN_ERR "can't get ads746 pen down GPIO\n");
+		return;
+	}
+
+	gpio_direction_input(ADS7846_PENDOWN);
+}
+
+static int ads7846_get_pendown_state(void)
+{
+	return !gpio_get_value(ADS7846_PENDOWN);
+}
+
+static struct ads7846_platform_data ads7846_config __initdata = {
+	.get_pendown_state	= ads7846_get_pendown_state,
+	.keep_vref_on		= 1,
+};
+
+static struct spi_board_info eukrea_mbimx27_spi_board_info[] __initdata = {
+	[0] = {
+		.modalias	= "ads7846",
+		.bus_num	= 0,
+		.chip_select	= 0,
+		.max_speed_hz	= 1500000,
+		.irq		= IRQ_GPIOD(25),
+		.platform_data	= &ads7846_config,
+		.mode           = SPI_MODE_2,
+	},
+};
+
+static int eukrea_mbimx27_spi_cs[] = {GPIO_PORTD | 28};
+
+static struct spi_imx_master eukrea_mbimx27_spi_0_data = {
+	.chipselect	= eukrea_mbimx27_spi_cs,
+	.num_chipselect = ARRAY_SIZE(eukrea_mbimx27_spi_cs),
+};
+#endif
+
+static struct platform_device *platform_devices[] __initdata = {
+	&leds_gpio,
+};
+
+/*
+ * system init for baseboard usage. Will be called by cpuimx27 init.
+ *
+ * Add platform devices present on this baseboard and init
+ * them from CPU side as far as required to use them later on
+ */
+void __init eukrea_mbimx27_baseboard_init(void)
+{
+	mxc_gpio_setup_multiple_pins(eukrea_mbimx27_pins,
+		ARRAY_SIZE(eukrea_mbimx27_pins), "MBIMX27");
+
+	mxc_register_device(&mxc_uart_device1, &uart_pdata[0]);
+	mxc_register_device(&mxc_uart_device2, &uart_pdata[1]);
+
+	mxc_register_device(&mxc_fb_device, &eukrea_mbimx27_fb_data);
+	mxc_register_device(&mxc_sdhc_device0, NULL);
+
+#if defined(CONFIG_TOUCHSCREEN_ADS7846)
+	|| defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+	/* SPI and ADS7846 Touchscreen controler init */
+	mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_OUT);
+	mxc_gpio_mode(GPIO_PORTD | 25 | GPIO_GPIO | GPIO_IN);
+	mxc_register_device(&mxc_spi_device0, &eukrea_mbimx27_spi_0_data);
+	spi_register_board_info(eukrea_mbimx27_spi_board_info,
+			ARRAY_SIZE(eukrea_mbimx27_spi_board_info));
+	ads7846_dev_init();
+#endif
+
+	/* Leds configuration */
+	mxc_gpio_mode(GPIO_PORTF | 16 | GPIO_GPIO | GPIO_OUT);
+	mxc_gpio_mode(GPIO_PORTF | 19 | GPIO_GPIO | GPIO_OUT);
+	/* Backlight */
+	mxc_gpio_mode(GPIO_PORTE | 5 | GPIO_GPIO | GPIO_OUT);
+
+	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
+}

arch/arm/plat-mxc/include/mach/board-eukrea_cpuimx27.h

@@ -22,4 +22,19 @@
 #ifndef __ASM_ARCH_MXC_BOARD_EUKREA_CPUIMX27_H__
 #define __ASM_ARCH_MXC_BOARD_EUKREA_CPUIMX27_H__
 
+#ifndef __ASSEMBLY__
+/*
+ * This CPU module needs a baseboard to work. After basic initializing
+ * its own devices, it calls baseboard's init function.
+ * TODO: Add your own baseboard init function and call it from
+ * inside eukrea_cpuimx27_init().
+ *
+ * This example here is for the development board. Refer
+ * eukrea_mbimx27-baseboard.c
+ */
+
+extern void eukrea_mbimx27_baseboard_init(void);
+
+#endif
+
 #endif /* __ASM_ARCH_MXC_BOARD_EUKREA_CPUIMX27_H__ */