[PATCH] sh: PCI updates

This updates some of the PCI drivers.  SH7751, the sh03 board-specific PCI
code, and some ST40 PCI updates are grouped in this.  
Signed-off-by: Paul Mundt <paul.mundt@nokia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

arch/sh/boards/se/7751/io.c

@@ -18,7 +18,7 @@
 #include <asm/addrspace.h>
 
 #include <linux/pci.h>
-#include <asm/pci-sh7751.h>
+#include "../../../drivers/pci/pci-sh7751.h"
 
 #if 0
 /******************************************************************

arch/sh/boards/se/7751/pci.c

@@ -19,7 +19,7 @@
 #include <linux/pci.h>
 
 #include <asm/io.h>
-#include <asm/pci-sh7751.h>
+#include "../../../drivers/pci/pci-sh7751.h"
 
 #define PCIMCR_MRSET_OFF	0xBFFFFFFF
 #define PCIMCR_RFSH_OFF		0xFFFFFFFB

arch/sh/drivers/pci/Makefile

@@ -13,4 +13,4 @@ obj-$(CONFIG_SH_DREAMCAST)		+= ops-dreamcast.o fixups-dreamcast.o \
 obj-$(CONFIG_SH_SECUREEDGE5410)		+= ops-snapgear.o
 obj-$(CONFIG_SH_BIGSUR)			+= ops-bigsur.o
 obj-$(CONFIG_SH_RTS7751R2D)		+= ops-rts7751r2d.o fixups-rts7751r2d.o
-
+obj-$(CONFIG_SH_SH03)			+= ops-sh03.o fixups-sh03.o

arch/sh/drivers/pci/fixups-rts7751r2d.c

@@ -18,15 +18,26 @@
 
 int pci_fixup_pcic(void)
 {
-	unsigned long mcr;
+	unsigned long bcr1, mcr;
 
-	outl(0xfb900047, SH7751_PCICONF1);
-	outl(0xab000001, SH7751_PCICONF4);
+	bcr1 = inl(SH7751_BCR1);
+	bcr1 |= 0x40080000;	/* Enable Bit 19 BREQEN, set PCIC to slave */
+	outl(bcr1, PCI_REG(SH7751_PCIBCR1));
+
+	/* Enable all interrupts, so we known what to fix */
+	outl(0x0000c3ff, PCI_REG(SH7751_PCIINTM));
+	outl(0x0000380f, PCI_REG(SH7751_PCIAINTM));
+
+	outl(0xfb900047, PCI_REG(SH7751_PCICONF1));
+	outl(0xab000001, PCI_REG(SH7751_PCICONF4));
 
 	mcr = inl(SH7751_MCR);
 	mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF;
-	outl(mcr, SH7751_PCIMCR);
+	outl(mcr, PCI_REG(SH7751_PCIMCR));
 
+	outl(0x0c000000, PCI_REG(SH7751_PCICONF5));
+	outl(0xd0000000, PCI_REG(SH7751_PCICONF6));
+	outl(0x0c000000, PCI_REG(SH7751_PCILAR0));
+	outl(0x00000000, PCI_REG(SH7751_PCILAR1));
 	return 0;
 }
-

arch/sh/drivers/pci/fixups-sh03.c

+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/pci.h>
+
+/*
+ * 	IRQ functions
+ */
+
+int __init pcibios_map_platform_irq(u8 slot, u8 pin, struct pci_dev *dev)
+{
+	int irq;
+
+	if (dev->bus->number == 0) {
+		switch (slot) {
+		case 4: return 5;	/* eth0       */
+		case 8: return 5;	/* eth1       */
+		case 6: return 2;	/* PCI bridge */
+		default:
+                	printk("PCI: Bad IRQ mapping request for slot %d\n", slot);
+                	return 2;
+		}
+	} else {
+		switch (pin) {
+		case 0:   irq =  2; break;
+		case 1:   irq =  2; break;
+		case 2:   irq =  2; break;
+		case 3:   irq =  2; break;
+		case 4:   irq =  2; break;
+		default:  irq = -1; break;
+		}
+	}
+	return irq;
+}
+
+static u8 __init sh03_no_swizzle(struct pci_dev *dev, u8 *pin)
+{
+	/* no swizzling */
+	return PCI_SLOT(dev->devfn);
+}
+
+static int sh03_pci_lookup_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	int irq = -1;
+
+	/* now lookup the actual IRQ on a platform specific basis (pci-'platform'.c) */
+	irq = pcibios_map_platform_irq(slot, pin, dev);
+	if( irq < 0 ) {
+		pr_debug("PCI: Error mapping IRQ on device %s\n", dev->slot_name);
+		return irq;
+	}
+
+	pr_debug("Setting IRQ for slot %s to %d\n", dev->slot_name, irq);
+
+	return irq;
+}
+
+void __init pcibios_fixup_irqs(void)
+{
+	pci_fixup_irqs(sh03_no_swizzle, sh03_pci_lookup_irq);
+}

arch/sh/drivers/pci/ops-rts7751r2d.c

@@ -61,7 +61,12 @@ EXPORT_SYMBOL(board_pci_channels);
 static struct sh7751_pci_address_map sh7751_pci_map = {
 	.window0	= {
 		.base	= SH7751_CS3_BASE_ADDR,
-		.size	= 0x03f00000,
+		.size	= 0x04000000,
+	},
+
+	.window1	= {
+		.base	= 0x00000000,	/* Unused */
+		.size	= 0x00000000,	/* Unused */
 	},
 
 	.flags	= SH7751_PCIC_NO_RESET,

arch/sh/drivers/pci/ops-sh03.c

+/*
+ * linux/arch/sh/drivers/pci/ops-sh03.c
+ *
+ * PCI initialization for the Interface CTP/PCI-SH03 board
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <asm/io.h>
+#include "pci-sh7751.h"
+
+/*
+ * Description:  This function sets up and initializes the pcic, sets
+ * up the BARS, maps the DRAM into the address space etc, etc.
+ */
+int __init pcibios_init_platform(void)
+{
+   return 1;
+}
+
+static struct resource sh7751_io_resource = {
+	.name   = "SH03 IO",
+	.start  = SH7751_PCI_IO_BASE,
+	.end    = SH7751_PCI_IO_BASE + SH7751_PCI_IO_SIZE - 1,
+	.flags  = IORESOURCE_IO
+};
+
+static struct resource sh7751_mem_resource = {
+	.name   = "SH03 mem",
+	.start  = SH7751_PCI_MEMORY_BASE,
+	.end    = SH7751_PCI_MEMORY_BASE + SH7751_PCI_MEM_SIZE - 1,
+	.flags  = IORESOURCE_MEM
+};
+
+extern struct pci_ops sh7751_pci_ops;
+
+struct pci_channel board_pci_channels[] = {
+	{ &sh7751_pci_ops, &sh7751_io_resource, &sh7751_mem_resource, 0, 0xff },
+	{ NULL, NULL, NULL, 0, 0 },
+};
+

arch/sh/drivers/pci/pci-auto.c

@@ -524,8 +524,10 @@ pciauto_bus_scan(struct pci_channel *hose, int top_bus, int current_bus)
 					 PCI_COMMAND, cmdstat | PCI_COMMAND_IO |
 					 PCI_COMMAND_MEMORY |
 					 PCI_COMMAND_MASTER);
+#if !defined(CONFIG_SH_HS7751RVOIP) && !defined(CONFIG_SH_RTS7751R2D)
 		early_write_config_byte(hose, top_bus, current_bus, pci_devfn,
 					PCI_LATENCY_TIMER, 0x80);
+#endif
 
 		/* Allocate PCI I/O and/or memory space */
 		pciauto_setup_bars(hose, top_bus, current_bus, pci_devfn, PCI_BASE_ADDRESS_5);

arch/sh/drivers/pci/pci-sh7751.c

@@ -33,6 +33,8 @@
 static unsigned int pci_probe = PCI_PROBE_CONF1;
 extern int pci_fixup_pcic(void);
 
+void pcibios_fixup_irqs(void) __attribute__ ((weak));
+
 /*
  * Direct access to PCI hardware...
  */
@@ -158,7 +160,6 @@ static int __init pci_check_direct(void)
  *  Handle bus scanning and fixups ....
  */
 
-#if !defined(CONFIG_SH_HS7751RVOIP) && !defined(CONFIG_SH_RTS7751R2D)
 static void __init pci_fixup_ide_bases(struct pci_dev *d)
 {
 	int i;
@@ -256,7 +257,7 @@ int __init sh7751_pcic_init(struct sh7751_pci_address_map *map)
 	outl(0, PCI_REG(SH7751_PCICLKR));
 	/* Clear Powerdown IRQ's (not done in reset) */
 	word = SH7751_PCIPINT_D3 | SH7751_PCIPINT_D0;
-	outl(word, PCI_REG(SH7751_PCICLKR));
+	outl(word, PCI_REG(SH7751_PCIPINT));
 
 	/*
 	 * This code is unused for some boards as it is done in the

arch/sh/drivers/pci/pci-st40.c

@@ -18,6 +18,7 @@
 #include <linux/types.h>
 #include <asm/pci.h>
 #include <linux/irq.h>
+#include <linux/interrupt.h>	/* irqreturn_t */
 
 #include "pci-st40.h"
 
@@ -28,24 +29,22 @@
 #define ST40PCI_REG_ADDRESS      (ST40PCI_BASE_ADDRESS+0x07000000)
 
 #define ST40PCI_REG(x) (ST40PCI_REG_ADDRESS+(ST40PCI_##x))
+#define ST40PCI_REG_INDEXED(reg, index) 				\
+	(ST40PCI_REG(reg##0) +					\
+	  ((ST40PCI_REG(reg##1) - ST40PCI_REG(reg##0))*index))
 
 #define ST40PCI_WRITE(reg,val) writel((val),ST40PCI_REG(reg))
 #define ST40PCI_WRITE_SHORT(reg,val) writew((val),ST40PCI_REG(reg))
 #define ST40PCI_WRITE_BYTE(reg,val) writeb((val),ST40PCI_REG(reg))
+#define ST40PCI_WRITE_INDEXED(reg, index, val)				\
+	 writel((val), ST40PCI_REG_INDEXED(reg, index));
 
 #define ST40PCI_READ(reg) readl(ST40PCI_REG(reg))
 #define ST40PCI_READ_SHORT(reg) readw(ST40PCI_REG(reg))
 #define ST40PCI_READ_BYTE(reg) readb(ST40PCI_REG(reg))
 
 #define ST40PCI_SERR_IRQ	64
-#define ST40PCI_SERR_INT_GROUP  0
-#define ST40PCI_SERR_INT_POS    0
-#define ST40PCI_SERR_INT_PRI    15
-
 #define ST40PCI_ERR_IRQ        	65
-#define ST40PCI_ERR_INT_GROUP   1
-#define ST40PCI_ERR_INT_POS     1
-#define ST40PCI_ERR_INT_PRI     14
 
 
 /* Macros to extract PLL params */
@@ -69,47 +68,143 @@
 #define PLL_25MHZ 0x793c8512
 #define PLL_33MHZ PLL_SET(18,88,3,295)
 
+static void pci_set_rbar_region(unsigned int region,     unsigned long localAddr,
+			 unsigned long pciOffset, unsigned long regionSize);
+
+/*
+ * The pcibios_map_platform_irq function is defined in the appropriate
+ * board specific code and referenced here
+ */
+extern int __init pcibios_map_platform_irq(struct pci_dev *dev, u8 slot, u8 pin);
 
 static __init void SetPCIPLL(void)
 {
-	/* Stop the PLL */
-	writel(0, PLLPCICR);
+	{
+		/* Lets play with the PLL values */
+		unsigned long pll1cr1;
+		unsigned long mdiv, ndiv, pdiv;
+		unsigned long muxcr;
+		unsigned int muxcr_ratios[4] = { 8, 16, 21, 1 };
+		unsigned int freq;
+
+#define CLKGENA            0xbb040000
+#define CLKGENA_PLL2_MUXCR CLKGENA + 0x48
+		pll1cr1 = ctrl_inl(PLLPCICR);
+		printk("PLL1CR1 %08lx\n", pll1cr1);
+		mdiv = PLL_MDIV(pll1cr1);
+		ndiv = PLL_NDIV(pll1cr1);
+		pdiv = PLL_PDIV(pll1cr1);
+		printk("mdiv %02lx ndiv %02lx pdiv %02lx\n", mdiv, ndiv, pdiv);
+		freq = ((2*27*ndiv)/mdiv) / (1 << pdiv);
+		printk("PLL freq %dMHz\n", freq);
+		muxcr = ctrl_inl(CLKGENA_PLL2_MUXCR);
+		printk("PCI freq %dMhz\n", freq / muxcr_ratios[muxcr & 3]);
+	}
+}
 
-	/* Always run at 33Mhz. The PCI clock is totally async 
-	 * to the rest of the system
-	 */
-	writel(PLL_33MHZ | PLLPCICR_POWERON, PLLPCICR);
 
-	printk("ST40PCI: Waiting for PCI PLL to lock\n");
-	while ((readl(PLLPCICR) & PLLPCICR_LOCK) == 0);
-	writel(readl(PLLPCICR) | PLLPCICR_OUT_EN, PLLPCICR);
+struct pci_err {
+  unsigned mask;
+  const char *error_string;
+};
+
+static struct pci_err int_error[]={
+  { INT_MNLTDIM,"MNLTDIM: Master non-lock transfer"},
+  { INT_TTADI,  "TTADI: Illegal byte enable in I/O transfer"},
+  { INT_TMTO,   "TMTO: Target memory read/write timeout"},
+  { INT_MDEI,   "MDEI: Master function disable error"},
+  { INT_APEDI,  "APEDI: Address parity error"},
+  { INT_SDI,    "SDI: SERR detected"},
+  { INT_DPEITW, "DPEITW: Data parity error target write"},
+  { INT_PEDITR, "PEDITR: PERR detected"},
+  { INT_TADIM,  "TADIM: Target abort detected"},
+  { INT_MADIM,  "MADIM: Master abort detected"},
+  { INT_MWPDI,  "MWPDI: PERR from target at data write"},
+  { INT_MRDPEI, "MRDPEI: Master read data parity error"}
+};
+#define NUM_PCI_INT_ERRS (sizeof(int_error)/sizeof(struct pci_err))
+
+static struct pci_err aint_error[]={
+  { AINT_MBI,   "MBI: Master broken"},
+  { AINT_TBTOI, "TBTOI: Target bus timeout"},
+  { AINT_MBTOI, "MBTOI: Master bus timeout"},
+  { AINT_TAI,   "TAI: Target abort"},
+  { AINT_MAI,   "MAI: Master abort"},
+  { AINT_RDPEI, "RDPEI: Read data parity"},
+  { AINT_WDPE,  "WDPE: Write data parity"}
+};
+
+#define NUM_PCI_AINT_ERRS (sizeof(aint_error)/sizeof(struct pci_err))
+
+static void print_pci_errors(unsigned reg,struct pci_err *error,int num_errors)
+{
+  int i;
+
+  for(i=0;i<num_errors;i++) {
+    if(reg & error[i].mask) {
+      printk("%s\n",error[i].error_string);
+    }
+  }
+
 }
 
 
+static char * pci_commands[16]={
+	"Int Ack",
+	"Special Cycle",
+	"I/O Read",
+	"I/O Write",
+	"Reserved",
+	"Reserved",
+	"Memory Read",
+	"Memory Write",
+	"Reserved",
+	"Reserved",
+	"Configuration Read",
+	"Configuration Write",
+	"Memory Read Multiple",
+	"Dual Address Cycle",
+	"Memory Read Line",
+	"Memory Write-and-Invalidate"
+};
+
 static irqreturn_t st40_pci_irq(int irq, void *dev_instance, struct pt_regs *regs)
 {
-
 	unsigned pci_int, pci_air, pci_cir, pci_aint;
+	static int count=0;
+
+
+	pci_int = ST40PCI_READ(INT);pci_aint = ST40PCI_READ(AINT);
+	pci_cir = ST40PCI_READ(CIR);pci_air = ST40PCI_READ(AIR);
+
+	/* Reset state to stop multiple interrupts */
+        ST40PCI_WRITE(INT, ~0); ST40PCI_WRITE(AINT, ~0);
+
+
+	if(++count>1) return IRQ_HANDLED;
 
-	pci_int = ST40PCI_READ(INT);
-	pci_cir = ST40PCI_READ(CIR);
-	pci_air = ST40PCI_READ(AIR);
+	printk("** PCI ERROR **\n");
 
-	if (pci_int) {
-		printk("PCI INTERRUPT!\n");
-		printk("PCI INT -> 0x%x\n", pci_int & 0xffff);
-		printk("PCI AIR -> 0x%x\n", pci_air);
-		printk("PCI CIR -> 0x%x\n", pci_cir);
-		ST40PCI_WRITE(INT, ~0);
+        if(pci_int) {
+		printk("** INT register status\n");
+		print_pci_errors(pci_int,int_error,NUM_PCI_INT_ERRS);
 	}
 
-	pci_aint = ST40PCI_READ(AINT);
-	if (pci_aint) {
-		printk("PCI ARB INTERRUPT!\n");
-		printk("PCI AINT -> 0x%x\n", pci_aint);
-		printk("PCI AIR -> 0x%x\n", pci_air);
-		printk("PCI CIR -> 0x%x\n", pci_cir);
-		ST40PCI_WRITE(AINT, ~0);
+        if(pci_aint) {
+		printk("** AINT register status\n");
+		print_pci_errors(pci_aint,aint_error,NUM_PCI_AINT_ERRS);
+	}
+
+	printk("** Address and command info\n");
+
+	printk("** Command  %s : Address 0x%x\n",
+	       pci_commands[pci_cir&0xf],pci_air);
+
+	if(pci_cir&CIR_PIOTEM) {
+		printk("CIR_PIOTEM:PIO transfer error for master\n");
+	}
+        if(pci_cir&CIR_RWTET) {
+		printk("CIR_RWTET:Read/Write transfer error for target\n");
 	}
 
 	return IRQ_HANDLED;
@@ -119,7 +214,7 @@ static irqreturn_t st40_pci_irq(int irq, void *dev_instance, struct pt_regs *reg
 /* Rounds a number UP to the nearest power of two. Used for
  * sizing the PCI window.
  */
-static u32 __init r2p2(u32 num)
+static u32 r2p2(u32 num)
 {
 	int i = 31;
 	u32 tmp = num;
@@ -179,12 +274,16 @@ int __init st40pci_init(unsigned memStart, unsigned memSize)
 	/* Loop while core resets */
 	while (ST40PCI_READ(CR) & CR_SOFT_RESET);
 
+	/* Switch off interrupts */
+	ST40PCI_WRITE(INTM, 0);
+	ST40PCI_WRITE(AINT, 0);
+
 	/* Now, lets reset all the cards on the bus with extreme prejudice */
 	ST40PCI_WRITE(CR, CR_LOCK_MASK | CR_RSTCTL);
 	udelay(250);
 
 	/* Set bus active, take it out of reset */
-	ST40PCI_WRITE(CR, CR_LOCK_MASK | CR_CFINT | CR_PFCS | CR_PFE);
+	ST40PCI_WRITE(CR, CR_LOCK_MASK | CR_BMAM | CR_CFINT | CR_PFCS | CR_PFE);
 
 	/* The PCI spec says that no access must be made to the bus until 1 second
 	 * after reset. This seem ludicrously long, but some delay is needed here
@@ -219,37 +318,20 @@ int __init st40pci_init(unsigned memStart, unsigned memSize)
 	/* Set up the 64K window */
 	ST40PCI_WRITE(IOBMR, 0x0);
 
-	/* Now we set up the mbars so the PCI bus can see the memory of the machine */
-
-	if (memSize < (64 * 1024)) {
-		printk("Ridiculous memory size of 0x%x?\n",memSize);
-		return 0;
-	}
-
-	lsr0 =
-	    (memSize >
-	     (512 * 1024 * 1024)) ? 0x1fff0001 : ((r2p2(memSize) -
-						   0x10000) | 0x1);
+	/* Now we set up the mbars so the PCI bus can see the local memory */
+	/* Expose a 256M window starting at PCI address 0... */
+	ST40PCI_WRITE(CSR_MBAR0, 0);
+	ST40PCI_WRITE(LSR0, 0x0fff0001);
 
-	ST40PCI_WRITE(LSR0, lsr0);
-
-	ST40PCI_WRITE(CSR_MBAR0, memStart);
-	ST40PCI_WRITE(LAR0, memStart);
+	/* ... and set up the initial incomming window to expose all of RAM */
+	pci_set_rbar_region(7, memStart, memStart, memSize);
 
 	/* Maximise timeout values */
 	ST40PCI_WRITE_BYTE(CSR_TRDY, 0xff);
 	ST40PCI_WRITE_BYTE(CSR_RETRY, 0xff);
 	ST40PCI_WRITE_BYTE(CSR_MIT, 0xff);
 
-
-	/* Install the pci interrupt handlers */
-	make_intc2_irq(ST40PCI_SERR_IRQ, INTC2_BASE0,
-		       ST40PCI_SERR_INT_GROUP, ST40PCI_SERR_INT_POS,
-		       ST40PCI_SERR_INT_PRI);
-
-	make_intc2_irq(ST40PCI_ERR_IRQ, INTC2_BASE0, ST40PCI_ERR_INT_GROUP,
-		       ST40PCI_ERR_INT_POS, ST40PCI_ERR_INT_PRI);
-
+	ST40PCI_WRITE_BYTE(PERF,PERF_MASTER_WRITE_POSTING);
 
 	return 1;
 }
@@ -332,7 +414,7 @@ static int st40pci_write(struct pci_bus *bus, unsigned int devfn, int where, int
 	return PCIBIOS_SUCCESSFUL;
 }
 
-static struct pci_ops pci_config_ops = {
+struct pci_ops st40pci_config_ops = {
 	.read = 	st40pci_read,
 	.write = 	st40pci_write,
 };
@@ -348,36 +430,12 @@ static u8 __init no_swizzle(struct pci_dev *dev, u8 * pin)
 }
 
 
-/* This needs to be shunted out of here into the board specific bit */
-#define HARP_PCI_IRQ    1
-#define HARP_BRIDGE_IRQ 2
-#define OVERDRIVE_SLOT0_IRQ 0
-
-static int __init map_harp_irq(struct pci_dev *dev, u8 slot, u8 pin)
-{
-	switch (slot) {
-#ifdef CONFIG_SH_STB1_HARP
-	case 2:		/*This is the PCI slot on the */
-		return HARP_PCI_IRQ;
-	case 1:		/* this is the bridge */
-		return HARP_BRIDGE_IRQ;
-#elif defined(CONFIG_SH_STB1_OVERDRIVE)
-	case 1:
-	case 2:
-	case 3:
-		return slot - 1;
-#else
-#error Unknown board
-#endif
-	default:
-		return -1;
-	}
-}
-
-void __init pcibios_init(void)
+static int __init pcibios_init(void)
 {
 	extern unsigned long memory_start, memory_end;
 
+	printk(KERN_ALERT "pci-st40.c: pcibios_init\n");
+
 	if (sh_mv.mv_init_pci != NULL) {
 		sh_mv.mv_init_pci();
 	}
@@ -392,7 +450,7 @@ void __init pcibios_init(void)
 	if (request_irq(ST40PCI_ERR_IRQ, st40_pci_irq, 
                         SA_INTERRUPT, "st40pci", NULL)) {
 		printk(KERN_ERR "st40pci: Cannot hook interrupt\n");
-		return;
+		return -EIO;
 	}
 
 	/* Enable the PCI interrupts on the device */
@@ -406,12 +464,46 @@ void __init pcibios_init(void)
 #endif
 
 	/* ok, do the scan man */
-	pci_root_bus = pci_scan_bus(0, &pci_config_ops, NULL);
+	pci_root_bus = pci_scan_bus(0, &st40pci_config_ops, NULL);
 	pci_assign_unassigned_resources();
-	pci_fixup_irqs(no_swizzle, map_harp_irq);
+	pci_fixup_irqs(no_swizzle, pcibios_map_platform_irq);
 
+	return 0;
 }
 
+subsys_initcall(pcibios_init);
+
 void __init pcibios_fixup_bus(struct pci_bus *bus)
 {
 }
+
+/*
+ * Publish a region of local address space over the PCI bus
+ * to other devices.
+ */
+static void pci_set_rbar_region(unsigned int region,     unsigned long localAddr,
+			 unsigned long pciOffset, unsigned long regionSize)
+{
+	unsigned long mask;
+
+	if (region > 7)
+		return;
+
+	if (regionSize > (512 * 1024 * 1024))
+		return;
+
+	mask = r2p2(regionSize) - 0x10000;
+
+	/* Diable the region (in case currently in use, should never happen) */
+	ST40PCI_WRITE_INDEXED(RSR, region, 0);
+
+	/* Start of local address space to publish */
+	ST40PCI_WRITE_INDEXED(RLAR, region, PHYSADDR(localAddr) );
+
+	/* Start of region in PCI address space as an offset from MBAR0 */
+	ST40PCI_WRITE_INDEXED(RBAR, region, pciOffset);
+
+	/* Size of region */
+	ST40PCI_WRITE_INDEXED(RSR, region, mask | 1);
+}
+

arch/sh/drivers/pci/pci-st40.h

@@ -33,13 +33,36 @@
 #define ST40PCI_LAR0          0x1c
 
 #define ST40PCI_INT           0x24
+#define INT_MNLTDIM           (1<<15)
+#define INT_TTADI             (1<<14)
+#define INT_TMTO              (1<<9)
+#define INT_MDEI              (1<<8)
+#define INT_APEDI             (1<<7)
+#define INT_SDI               (1<<6)
+#define INT_DPEITW            (1<<5)
+#define INT_PEDITR            (1<<4)
+#define INT_TADIM             (1<<3)
 #define INT_MADIM             (1<<2)
+#define INT_MWPDI             (1<<1)
+#define INT_MRDPEI            (1<<0)
 
 
 #define ST40PCI_INTM          0x28
 #define ST40PCI_AIR           0x2c
+
 #define ST40PCI_CIR           0x30
+#define CIR_PIOTEM            (1<<31)
+#define CIR_RWTET             (1<<26)
+
 #define ST40PCI_AINT          0x40
+#define AINT_MBI              (1<<13)
+#define AINT_TBTOI            (1<<12)
+#define AINT_MBTOI            (1<<11)
+#define AINT_TAI              (1<<3)
+#define AINT_MAI              (1<<2)
+#define AINT_RDPEI            (1<<1)
+#define AINT_WDPE             (1<<0)
+
 #define ST40PCI_AINTM         0x44
 #define ST40PCI_BMIR          0x48
 #define ST40PCI_PAR           0x4c
@@ -51,6 +74,53 @@
 #define ST40PCI_IOBMR         0x74
 #define ST40PCI_PDR           0x78
 
+/* H8 specific registers start here */
+#define ST40PCI_WCBAR         0x7c
+#define ST40PCI_LOCCFG_UNLOCK 0x34
+
+#define ST40PCI_RBAR0         0x100
+#define ST40PCI_RSR0          0x104
+#define ST40PCI_RLAR0         0x108
+
+#define ST40PCI_RBAR1         0x110
+#define ST40PCI_RSR1          0x114
+#define ST40PCI_RLAR1         0x118
+
+
+#define ST40PCI_RBAR2         0x120
+#define ST40PCI_RSR2          0x124
+#define ST40PCI_RLAR2         0x128
+
+#define ST40PCI_RBAR3         0x130
+#define ST40PCI_RSR3          0x134
+#define ST40PCI_RLAR3         0x138
+
+#define ST40PCI_RBAR4         0x140
+#define ST40PCI_RSR4          0x144
+#define ST40PCI_RLAR4         0x148
+
+#define ST40PCI_RBAR5         0x150
+#define ST40PCI_RSR5          0x154
+#define ST40PCI_RLAR5         0x158
+
+#define ST40PCI_RBAR6         0x160
+#define ST40PCI_RSR6          0x164
+#define ST40PCI_RLAR6         0x168
+
+#define ST40PCI_RBAR7         0x170
+#define ST40PCI_RSR7          0x174
+#define ST40PCI_RLAR7         0x178
+
+
+#define ST40PCI_RBAR(n)      (0x100+(0x10*(n)))
+#define ST40PCI_RSR(n)       (0x104+(0x10*(n)))
+#define ST40PCI_RLAR(n)      (0x108+(0x10*(n)))
+
+#define ST40PCI_PERF               0x80
+#define PERF_MASTER_WRITE_POSTING  (1<<4)
+/* H8 specific registers end here */
+
+
 /* These are configs space registers */
 #define ST40PCI_CSR_VID               0x10000
 #define ST40PCI_CSR_DID               0x10002

arch/sh/drivers/pci/pci.c

@@ -106,6 +106,8 @@ int pcibios_enable_device(struct pci_dev *dev, int mask)
 	pci_read_config_word(dev, PCI_COMMAND, &cmd);
 	old_cmd = cmd;
 	for(idx=0; idx<6; idx++) {
+		if (!(mask & (1 << idx)))
+			continue;
 		r = &dev->resource[idx];
 		if (!r->start && r->end) {
 			printk(KERN_ERR "PCI: Device %s not available because "