Commit b37bde14 authored by Bryan Wu's avatar Bryan Wu Committed by David Woodhouse

[MTD] [NAND] Blackfin on-chip NAND Flash Controller driver

This is the driver for latest Blackfin on-chip nand flash controller

 - use nand_chip and mtd_info common nand driver interface
 - provide both PIO and dma operation
 - compiled with ezkit bf548 configuration
 - use hardware 1-bit ECC
 - tested with YAFFS2 and can mount YAFFS2 filesystem as rootfs

ChangeLog from try#1
 - use hweight32() instead of count_bits()
 - replace bf54x with bf5xx and BF54X with BF5XX
 - compare against plat->page_size in 2 cases when enable hardware ECC

ChangeLog from try#2
 - passed nand_test suites
 - use cpu_relax() instead of busy wait loop
 - some coding style issue pointed out by Andrew
Signed-off-by: default avatarBryan Wu <bryan.wu@analog.com>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarDavid Woodhouse <dwmw2@infradead.org>
parent c4a9f88d
......@@ -91,6 +91,25 @@ config MTD_NAND_AU1550
This enables the driver for the NAND flash controller on the
AMD/Alchemy 1550 SOC.
config MTD_NAND_BF5XX
tristate "Blackfin on-chip NAND Flash Controller driver"
depends on BF54x && MTD_NAND
help
This enables the Blackfin on-chip NAND flash controller
No board specific support is done by this driver, each board
must advertise a platform_device for the driver to attach.
This driver can also be built as a module. If so, the module
will be called bf5xx-nand.
config MTD_NAND_BF5XX_HWECC
bool "BF5XX NAND Hardware ECC"
depends on MTD_NAND_BF5XX
help
Enable the use of the BF5XX's internal ECC generator when
using NAND.
config MTD_NAND_RTC_FROM4
tristate "Renesas Flash ROM 4-slot interface board (FROM_BOARD4)"
depends on SH_SOLUTION_ENGINE
......
......@@ -13,6 +13,7 @@ obj-$(CONFIG_MTD_NAND_TOTO) += toto.o
obj-$(CONFIG_MTD_NAND_AUTCPU12) += autcpu12.o
obj-$(CONFIG_MTD_NAND_EDB7312) += edb7312.o
obj-$(CONFIG_MTD_NAND_AU1550) += au1550nd.o
obj-$(CONFIG_MTD_NAND_BF5XX) += bf5xx_nand.o
obj-$(CONFIG_MTD_NAND_PPCHAMELEONEVB) += ppchameleonevb.o
obj-$(CONFIG_MTD_NAND_S3C2410) += s3c2410.o
obj-$(CONFIG_MTD_NAND_DISKONCHIP) += diskonchip.o
......
/* linux/drivers/mtd/nand/bf5xx_nand.c
*
* Copyright 2006-2007 Analog Devices Inc.
* http://blackfin.uclinux.org/
* Bryan Wu <bryan.wu@analog.com>
*
* Blackfin BF5xx on-chip NAND flash controler driver
*
* Derived from drivers/mtd/nand/s3c2410.c
* Copyright (c) 2007 Ben Dooks <ben@simtec.co.uk>
*
* Derived from drivers/mtd/nand/cafe.c
* Copyright © 2006 Red Hat, Inc.
* Copyright © 2006 David Woodhouse <dwmw2@infradead.org>
*
* Changelog:
* 12-Jun-2007 Bryan Wu: Initial version
* 18-Jul-2007 Bryan Wu:
* - ECC_HW and ECC_SW supported
* - DMA supported in ECC_HW
* - YAFFS tested as rootfs in both ECC_HW and ECC_SW
*
* TODO:
* Enable JFFS2 over NAND as rootfs
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/module.h>
#include <linux/types.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/ioport.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/dma-mapping.h>
#include <linux/err.h>
#include <linux/slab.h>
#include <linux/io.h>
#include <linux/bitops.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/nand_ecc.h>
#include <linux/mtd/partitions.h>
#include <asm/blackfin.h>
#include <asm/dma.h>
#include <asm/cacheflush.h>
#include <asm/nand.h>
#include <asm/portmux.h>
#define DRV_NAME "bf5xx-nand"
#define DRV_VERSION "1.2"
#define DRV_AUTHOR "Bryan Wu <bryan.wu@analog.com>"
#define DRV_DESC "BF5xx on-chip NAND FLash Controller Driver"
#ifdef CONFIG_MTD_NAND_BF5XX_HWECC
static int hardware_ecc = 1;
#else
static int hardware_ecc;
#endif
static unsigned short bfin_nfc_pin_req[] = {P_NAND_CE, P_NAND_RB, 0};
/*
* Data structures for bf5xx nand flash controller driver
*/
/* bf5xx nand info */
struct bf5xx_nand_info {
/* mtd info */
struct nand_hw_control controller;
struct mtd_info mtd;
struct nand_chip chip;
/* platform info */
struct bf5xx_nand_platform *platform;
/* device info */
struct device *device;
/* DMA stuff */
struct completion dma_completion;
};
/*
* Conversion functions
*/
static struct bf5xx_nand_info *mtd_to_nand_info(struct mtd_info *mtd)
{
return container_of(mtd, struct bf5xx_nand_info, mtd);
}
static struct bf5xx_nand_info *to_nand_info(struct platform_device *pdev)
{
return platform_get_drvdata(pdev);
}
static struct bf5xx_nand_platform *to_nand_plat(struct platform_device *pdev)
{
return pdev->dev.platform_data;
}
/*
* struct nand_chip interface function pointers
*/
/*
* bf5xx_nand_hwcontrol
*
* Issue command and address cycles to the chip
*/
static void bf5xx_nand_hwcontrol(struct mtd_info *mtd, int cmd,
unsigned int ctrl)
{
if (cmd == NAND_CMD_NONE)
return;
while (bfin_read_NFC_STAT() & WB_FULL)
cpu_relax();
if (ctrl & NAND_CLE)
bfin_write_NFC_CMD(cmd);
else
bfin_write_NFC_ADDR(cmd);
SSYNC();
}
/*
* bf5xx_nand_devready()
*
* returns 0 if the nand is busy, 1 if it is ready
*/
static int bf5xx_nand_devready(struct mtd_info *mtd)
{
unsigned short val = bfin_read_NFC_IRQSTAT();
if ((val & NBUSYIRQ) == NBUSYIRQ)
return 1;
else
return 0;
}
/*
* ECC functions
* These allow the bf5xx to use the controller's ECC
* generator block to ECC the data as it passes through
*/
/*
* ECC error correction function
*/
static int bf5xx_nand_correct_data_256(struct mtd_info *mtd, u_char *dat,
u_char *read_ecc, u_char *calc_ecc)
{
struct bf5xx_nand_info *info = mtd_to_nand_info(mtd);
u32 syndrome[5];
u32 calced, stored;
int i;
unsigned short failing_bit, failing_byte;
u_char data;
calced = calc_ecc[0] | (calc_ecc[1] << 8) | (calc_ecc[2] << 16);
stored = read_ecc[0] | (read_ecc[1] << 8) | (read_ecc[2] << 16);
syndrome[0] = (calced ^ stored);
/*
* syndrome 0: all zero
* No error in data
* No action
*/
if (!syndrome[0] || !calced || !stored)
return 0;
/*
* sysdrome 0: only one bit is one
* ECC data was incorrect
* No action
*/
if (hweight32(syndrome[0]) == 1) {
dev_err(info->device, "ECC data was incorrect!\n");
return 1;
}
syndrome[1] = (calced & 0x7FF) ^ (stored & 0x7FF);
syndrome[2] = (calced & 0x7FF) ^ ((calced >> 11) & 0x7FF);
syndrome[3] = (stored & 0x7FF) ^ ((stored >> 11) & 0x7FF);
syndrome[4] = syndrome[2] ^ syndrome[3];
for (i = 0; i < 5; i++)
dev_info(info->device, "syndrome[%d] 0x%08x\n", i, syndrome[i]);
dev_info(info->device,
"calced[0x%08x], stored[0x%08x]\n",
calced, stored);
/*
* sysdrome 0: exactly 11 bits are one, each parity
* and parity' pair is 1 & 0 or 0 & 1.
* 1-bit correctable error
* Correct the error
*/
if (hweight32(syndrome[0]) == 11 && syndrome[4] == 0x7FF) {
dev_info(info->device,
"1-bit correctable error, correct it.\n");
dev_info(info->device,
"syndrome[1] 0x%08x\n", syndrome[1]);
failing_bit = syndrome[1] & 0x7;
failing_byte = syndrome[1] >> 0x3;
data = *(dat + failing_byte);
data = data ^ (0x1 << failing_bit);
*(dat + failing_byte) = data;
return 0;
}
/*
* sysdrome 0: random data
* More than 1-bit error, non-correctable error
* Discard data, mark bad block
*/
dev_err(info->device,
"More than 1-bit error, non-correctable error.\n");
dev_err(info->device,
"Please discard data, mark bad block\n");
return 1;
}
static int bf5xx_nand_correct_data(struct mtd_info *mtd, u_char *dat,
u_char *read_ecc, u_char *calc_ecc)
{
struct bf5xx_nand_info *info = mtd_to_nand_info(mtd);
struct bf5xx_nand_platform *plat = info->platform;
unsigned short page_size = (plat->page_size ? 512 : 256);
int ret;
ret = bf5xx_nand_correct_data_256(mtd, dat, read_ecc, calc_ecc);
/* If page size is 512, correct second 256 bytes */
if (page_size == 512) {
dat += 256;
read_ecc += 8;
calc_ecc += 8;
ret = bf5xx_nand_correct_data_256(mtd, dat, read_ecc, calc_ecc);
}
return ret;
}
static void bf5xx_nand_enable_hwecc(struct mtd_info *mtd, int mode)
{
return;
}
static int bf5xx_nand_calculate_ecc(struct mtd_info *mtd,
const u_char *dat, u_char *ecc_code)
{
struct bf5xx_nand_info *info = mtd_to_nand_info(mtd);
struct bf5xx_nand_platform *plat = info->platform;
u16 page_size = (plat->page_size ? 512 : 256);
u16 ecc0, ecc1;
u32 code[2];
u8 *p;
int bytes = 3, i;
/* first 4 bytes ECC code for 256 page size */
ecc0 = bfin_read_NFC_ECC0();
ecc1 = bfin_read_NFC_ECC1();
code[0] = (ecc0 & 0x3FF) | ((ecc1 & 0x3FF) << 11);
dev_dbg(info->device, "returning ecc 0x%08x\n", code[0]);
/* second 4 bytes ECC code for 512 page size */
if (page_size == 512) {
ecc0 = bfin_read_NFC_ECC2();
ecc1 = bfin_read_NFC_ECC3();
code[1] = (ecc0 & 0x3FF) | ((ecc1 & 0x3FF) << 11);
bytes = 6;
dev_dbg(info->device, "returning ecc 0x%08x\n", code[1]);
}
p = (u8 *)code;
for (i = 0; i < bytes; i++)
ecc_code[i] = p[i];
return 0;
}
/*
* PIO mode for buffer writing and reading
*/
static void bf5xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
{
int i;
unsigned short val;
/*
* Data reads are requested by first writing to NFC_DATA_RD
* and then reading back from NFC_READ.
*/
for (i = 0; i < len; i++) {
while (bfin_read_NFC_STAT() & WB_FULL)
cpu_relax();
/* Contents do not matter */
bfin_write_NFC_DATA_RD(0x0000);
SSYNC();
while ((bfin_read_NFC_IRQSTAT() & RD_RDY) != RD_RDY)
cpu_relax();
buf[i] = bfin_read_NFC_READ();
val = bfin_read_NFC_IRQSTAT();
val |= RD_RDY;
bfin_write_NFC_IRQSTAT(val);
SSYNC();
}
}
static uint8_t bf5xx_nand_read_byte(struct mtd_info *mtd)
{
uint8_t val;
bf5xx_nand_read_buf(mtd, &val, 1);
return val;
}
static void bf5xx_nand_write_buf(struct mtd_info *mtd,
const uint8_t *buf, int len)
{
int i;
for (i = 0; i < len; i++) {
while (bfin_read_NFC_STAT() & WB_FULL)
cpu_relax();
bfin_write_NFC_DATA_WR(buf[i]);
SSYNC();
}
}
static void bf5xx_nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
{
int i;
u16 *p = (u16 *) buf;
len >>= 1;
/*
* Data reads are requested by first writing to NFC_DATA_RD
* and then reading back from NFC_READ.
*/
bfin_write_NFC_DATA_RD(0x5555);
SSYNC();
for (i = 0; i < len; i++)
p[i] = bfin_read_NFC_READ();
}
static void bf5xx_nand_write_buf16(struct mtd_info *mtd,
const uint8_t *buf, int len)
{
int i;
u16 *p = (u16 *) buf;
len >>= 1;
for (i = 0; i < len; i++)
bfin_write_NFC_DATA_WR(p[i]);
SSYNC();
}
/*
* DMA functions for buffer writing and reading
*/
static irqreturn_t bf5xx_nand_dma_irq(int irq, void *dev_id)
{
struct bf5xx_nand_info *info = dev_id;
clear_dma_irqstat(CH_NFC);
disable_dma(CH_NFC);
complete(&info->dma_completion);
return IRQ_HANDLED;
}
static int bf5xx_nand_dma_rw(struct mtd_info *mtd,
uint8_t *buf, int is_read)
{
struct bf5xx_nand_info *info = mtd_to_nand_info(mtd);
struct bf5xx_nand_platform *plat = info->platform;
unsigned short page_size = (plat->page_size ? 512 : 256);
unsigned short val;
dev_dbg(info->device, " mtd->%p, buf->%p, is_read %d\n",
mtd, buf, is_read);
/*
* Before starting a dma transfer, be sure to invalidate/flush
* the cache over the address range of your DMA buffer to
* prevent cache coherency problems. Otherwise very subtle bugs
* can be introduced to your driver.
*/
if (is_read)
invalidate_dcache_range((unsigned int)buf,
(unsigned int)(buf + page_size));
else
flush_dcache_range((unsigned int)buf,
(unsigned int)(buf + page_size));
/*
* This register must be written before each page is
* transferred to generate the correct ECC register
* values.
*/
bfin_write_NFC_RST(0x1);
SSYNC();
disable_dma(CH_NFC);
clear_dma_irqstat(CH_NFC);
/* setup DMA register with Blackfin DMA API */
set_dma_config(CH_NFC, 0x0);
set_dma_start_addr(CH_NFC, (unsigned long) buf);
set_dma_x_count(CH_NFC, (page_size >> 2));
set_dma_x_modify(CH_NFC, 4);
/* setup write or read operation */
val = DI_EN | WDSIZE_32;
if (is_read)
val |= WNR;
set_dma_config(CH_NFC, val);
enable_dma(CH_NFC);
/* Start PAGE read/write operation */
if (is_read)
bfin_write_NFC_PGCTL(0x1);
else
bfin_write_NFC_PGCTL(0x2);
wait_for_completion(&info->dma_completion);
return 0;
}
static void bf5xx_nand_dma_read_buf(struct mtd_info *mtd,
uint8_t *buf, int len)
{
struct bf5xx_nand_info *info = mtd_to_nand_info(mtd);
struct bf5xx_nand_platform *plat = info->platform;
unsigned short page_size = (plat->page_size ? 512 : 256);
dev_dbg(info->device, "mtd->%p, buf->%p, int %d\n", mtd, buf, len);
if (len == page_size)
bf5xx_nand_dma_rw(mtd, buf, 1);
else
bf5xx_nand_read_buf(mtd, buf, len);
}
static void bf5xx_nand_dma_write_buf(struct mtd_info *mtd,
const uint8_t *buf, int len)
{
struct bf5xx_nand_info *info = mtd_to_nand_info(mtd);
struct bf5xx_nand_platform *plat = info->platform;
unsigned short page_size = (plat->page_size ? 512 : 256);
dev_dbg(info->device, "mtd->%p, buf->%p, len %d\n", mtd, buf, len);
if (len == page_size)
bf5xx_nand_dma_rw(mtd, (uint8_t *)buf, 0);
else
bf5xx_nand_write_buf(mtd, buf, len);
}
/*
* System initialization functions
*/
static int bf5xx_nand_dma_init(struct bf5xx_nand_info *info)
{
int ret;
unsigned short val;
/* Do not use dma */
if (!hardware_ecc)
return 0;
init_completion(&info->dma_completion);
/* Setup DMAC1 channel mux for NFC which shared with SDH */
val = bfin_read_DMAC1_PERIMUX();
val &= 0xFFFE;
bfin_write_DMAC1_PERIMUX(val);
SSYNC();
/* Request NFC DMA channel */
ret = request_dma(CH_NFC, "BF5XX NFC driver");
if (ret < 0) {
dev_err(info->device, " unable to get DMA channel\n");
return ret;
}
set_dma_callback(CH_NFC, (void *) bf5xx_nand_dma_irq, (void *) info);
/* Turn off the DMA channel first */
disable_dma(CH_NFC);
return 0;
}
/*
* BF5XX NFC hardware initialization
* - pin mux setup
* - clear interrupt status
*/
static int bf5xx_nand_hw_init(struct bf5xx_nand_info *info)
{
int err = 0;
unsigned short val;
struct bf5xx_nand_platform *plat = info->platform;
/* setup NFC_CTL register */
dev_info(info->device,
"page_size=%d, data_width=%d, wr_dly=%d, rd_dly=%d\n",
(plat->page_size ? 512 : 256),
(plat->data_width ? 16 : 8),
plat->wr_dly, plat->rd_dly);
val = (plat->page_size << NFC_PG_SIZE_OFFSET) |
(plat->data_width << NFC_NWIDTH_OFFSET) |
(plat->rd_dly << NFC_RDDLY_OFFSET) |
(plat->rd_dly << NFC_WRDLY_OFFSET);
dev_dbg(info->device, "NFC_CTL is 0x%04x\n", val);
bfin_write_NFC_CTL(val);
SSYNC();
/* clear interrupt status */
bfin_write_NFC_IRQMASK(0x0);
SSYNC();
val = bfin_read_NFC_IRQSTAT();
bfin_write_NFC_IRQSTAT(val);
SSYNC();
if (peripheral_request_list(bfin_nfc_pin_req, DRV_NAME)) {
printk(KERN_ERR DRV_NAME
": Requesting Peripherals failed\n");
return -EFAULT;
}
/* DMA initialization */
if (bf5xx_nand_dma_init(info))
err = -ENXIO;
return err;
}
/*
* Device management interface
*/
static int bf5xx_nand_add_partition(struct bf5xx_nand_info *info)
{
struct mtd_info *mtd = &info->mtd;
#ifdef CONFIG_MTD_PARTITIONS
struct mtd_partition *parts = info->platform->partitions;
int nr = info->platform->nr_partitions;
return add_mtd_partitions(mtd, parts, nr);
#else
return add_mtd_device(mtd);
#endif
}
static int bf5xx_nand_remove(struct platform_device *pdev)
{
struct bf5xx_nand_info *info = to_nand_info(pdev);
struct mtd_info *mtd = NULL;
platform_set_drvdata(pdev, NULL);
/* first thing we need to do is release all our mtds
* and their partitions, then go through freeing the
* resources used
*/
mtd = &info->mtd;
if (mtd) {
nand_release(mtd);
kfree(mtd);
}
peripheral_free_list(bfin_nfc_pin_req);
/* free the common resources */
kfree(info);
return 0;
}
/*
* bf5xx_nand_probe
*
* called by device layer when it finds a device matching
* one our driver can handled. This code checks to see if
* it can allocate all necessary resources then calls the
* nand layer to look for devices
*/
static int bf5xx_nand_probe(struct platform_device *pdev)
{
struct bf5xx_nand_platform *plat = to_nand_plat(pdev);
struct bf5xx_nand_info *info = NULL;
struct nand_chip *chip = NULL;
struct mtd_info *mtd = NULL;
int err = 0;
dev_dbg(&pdev->dev, "(%p)\n", pdev);
if (!plat) {
dev_err(&pdev->dev, "no platform specific information\n");
goto exit_error;
}
info = kzalloc(sizeof(*info), GFP_KERNEL);
if (info == NULL) {
dev_err(&pdev->dev, "no memory for flash info\n");
err = -ENOMEM;
goto exit_error;
}
platform_set_drvdata(pdev, info);
spin_lock_init(&info->controller.lock);
init_waitqueue_head(&info->controller.wq);
info->device = &pdev->dev;
info->platform = plat;
/* initialise chip data struct */
chip = &info->chip;
if (plat->data_width)
chip->options |= NAND_BUSWIDTH_16;
chip->options |= NAND_CACHEPRG | NAND_SKIP_BBTSCAN;
chip->read_buf = (plat->data_width) ?
bf5xx_nand_read_buf16 : bf5xx_nand_read_buf;
chip->write_buf = (plat->data_width) ?
bf5xx_nand_write_buf16 : bf5xx_nand_write_buf;
chip->read_byte = bf5xx_nand_read_byte;
chip->cmd_ctrl = bf5xx_nand_hwcontrol;
chip->dev_ready = bf5xx_nand_devready;
chip->priv = &info->mtd;
chip->controller = &info->controller;
chip->IO_ADDR_R = (void __iomem *) NFC_READ;
chip->IO_ADDR_W = (void __iomem *) NFC_DATA_WR;
chip->chip_delay = 0;
/* initialise mtd info data struct */
mtd = &info->mtd;
mtd->priv = chip;
mtd->owner = THIS_MODULE;
/* initialise the hardware */
err = bf5xx_nand_hw_init(info);
if (err != 0)
goto exit_error;
/* setup hardware ECC data struct */
if (hardware_ecc) {
if (plat->page_size == NFC_PG_SIZE_256) {
chip->ecc.bytes = 3;
chip->ecc.size = 256;
} else if (plat->page_size == NFC_PG_SIZE_512) {
chip->ecc.bytes = 6;
chip->ecc.size = 512;
}
chip->read_buf = bf5xx_nand_dma_read_buf;
chip->write_buf = bf5xx_nand_dma_write_buf;
chip->ecc.calculate = bf5xx_nand_calculate_ecc;
chip->ecc.correct = bf5xx_nand_correct_data;
chip->ecc.mode = NAND_ECC_HW;
chip->ecc.hwctl = bf5xx_nand_enable_hwecc;
} else {
chip->ecc.mode = NAND_ECC_SOFT;
}
/* scan hardware nand chip and setup mtd info data struct */
if (nand_scan(mtd, 1)) {
err = -ENXIO;
goto exit_error;
}
/* add NAND partition */
bf5xx_nand_add_partition(info);
dev_dbg(&pdev->dev, "initialised ok\n");
return 0;
exit_error:
bf5xx_nand_remove(pdev);
if (err == 0)
err = -EINVAL;
return err;
}
/* PM Support */
#ifdef CONFIG_PM
static int bf5xx_nand_suspend(struct platform_device *dev, pm_message_t pm)
{
struct bf5xx_nand_info *info = platform_get_drvdata(dev);
return 0;
}
static int bf5xx_nand_resume(struct platform_device *dev)
{
struct bf5xx_nand_info *info = platform_get_drvdata(dev);
if (info)
bf5xx_nand_hw_init(info);
return 0;
}
#else
#define bf5xx_nand_suspend NULL
#define bf5xx_nand_resume NULL
#endif
/* driver device registration */
static struct platform_driver bf5xx_nand_driver = {
.probe = bf5xx_nand_probe,
.remove = bf5xx_nand_remove,
.suspend = bf5xx_nand_suspend,
.resume = bf5xx_nand_resume,
.driver = {
.name = DRV_NAME,
.owner = THIS_MODULE,
},
};
static int __init bf5xx_nand_init(void)
{
printk(KERN_INFO "%s, Version %s (c) 2007 Analog Devices, Inc.\n",
DRV_DESC, DRV_VERSION);
return platform_driver_register(&bf5xx_nand_driver);
}
static void __exit bf5xx_nand_exit(void)
{
platform_driver_unregister(&bf5xx_nand_driver);
}
module_init(bf5xx_nand_init);
module_exit(bf5xx_nand_exit);
MODULE_LICENSE("GPL");
MODULE_AUTHOR(DRV_AUTHOR);
MODULE_DESCRIPTION(DRV_DESC);
......@@ -55,6 +55,7 @@
#define CH_SPORT3_RX 20
#define CH_SPORT3_TX 21
#define CH_SDH 22
#define CH_NFC 22
#define CH_SPI2 23
#define CH_MEM_STREAM0_DEST 24
......
/* linux/include/asm-blackfin/nand.h
*
* Copyright (c) 2007 Analog Devices, Inc.
* Bryan Wu <bryan.wu@analog.com>
*
* BF5XX - NAND flash controller platfrom_device info
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/* struct bf5xx_nand_platform
*
* define a interface between platfrom board specific code and
* bf54x NFC driver.
*
* nr_partitions = number of partitions pointed to be partitoons (or zero)
* partitions = mtd partition list
*/
#define NFC_PG_SIZE_256 0
#define NFC_PG_SIZE_512 1
#define NFC_PG_SIZE_OFFSET 9
#define NFC_NWIDTH_8 0
#define NFC_NWIDTH_16 1
#define NFC_NWIDTH_OFFSET 8
#define NFC_RDDLY_OFFSET 4
#define NFC_WRDLY_OFFSET 0
#define NFC_STAT_NBUSY 1
struct bf5xx_nand_platform {
/* NAND chip information */
unsigned short page_size;
unsigned short data_width;
/* RD/WR strobe delay timing information, all times in SCLK cycles */
unsigned short rd_dly;
unsigned short wr_dly;
/* NAND MTD partition information */
int nr_partitions;
struct mtd_partition *partitions;
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment