Commit b5de1ce0 authored by Olof Johansson's avatar Olof Johansson

Merge tag 'qcom-drivers-for-3.16-2' of...

Merge tag 'qcom-drivers-for-3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/drivers

Merge "Qualcomm ARM Based driver Updates for v3.16-2" from Kumar Gala:

* Updated MSM uart driver to not access GSBI control registers

* tag 'qcom-drivers-for-3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
  tty: serial: msm: Remove direct access to GSBI
Signed-off-by: default avatarOlof Johansson <olof@lixom.net>
parents 182434f7 31964ffe
......@@ -52,7 +52,6 @@ struct msm_port {
struct clk *clk;
struct clk *pclk;
unsigned int imr;
void __iomem *gsbi_base;
int is_uartdm;
unsigned int old_snap_state;
};
......@@ -599,9 +598,7 @@ static const char *msm_type(struct uart_port *port)
static void msm_release_port(struct uart_port *port)
{
struct platform_device *pdev = to_platform_device(port->dev);
struct msm_port *msm_port = UART_TO_MSM(port);
struct resource *uart_resource;
struct resource *gsbi_resource;
resource_size_t size;
uart_resource = platform_get_resource(pdev, IORESOURCE_MEM, 0);
......@@ -612,28 +609,12 @@ static void msm_release_port(struct uart_port *port)
release_mem_region(port->mapbase, size);
iounmap(port->membase);
port->membase = NULL;
if (msm_port->gsbi_base) {
writel_relaxed(GSBI_PROTOCOL_IDLE,
msm_port->gsbi_base + GSBI_CONTROL);
gsbi_resource = platform_get_resource(pdev, IORESOURCE_MEM, 1);
if (unlikely(!gsbi_resource))
return;
size = resource_size(gsbi_resource);
release_mem_region(gsbi_resource->start, size);
iounmap(msm_port->gsbi_base);
msm_port->gsbi_base = NULL;
}
}
static int msm_request_port(struct uart_port *port)
{
struct msm_port *msm_port = UART_TO_MSM(port);
struct platform_device *pdev = to_platform_device(port->dev);
struct resource *uart_resource;
struct resource *gsbi_resource;
resource_size_t size;
int ret;
......@@ -652,30 +633,8 @@ static int msm_request_port(struct uart_port *port)
goto fail_release_port;
}
gsbi_resource = platform_get_resource(pdev, IORESOURCE_MEM, 1);
/* Is this a GSBI-based port? */
if (gsbi_resource) {
size = resource_size(gsbi_resource);
if (!request_mem_region(gsbi_resource->start, size,
"msm_serial")) {
ret = -EBUSY;
goto fail_release_port_membase;
}
msm_port->gsbi_base = ioremap(gsbi_resource->start, size);
if (!msm_port->gsbi_base) {
ret = -EBUSY;
goto fail_release_gsbi;
}
}
return 0;
fail_release_gsbi:
release_mem_region(gsbi_resource->start, size);
fail_release_port_membase:
iounmap(port->membase);
fail_release_port:
release_mem_region(port->mapbase, size);
return ret;
......@@ -683,7 +642,6 @@ static int msm_request_port(struct uart_port *port)
static void msm_config_port(struct uart_port *port, int flags)
{
struct msm_port *msm_port = UART_TO_MSM(port);
int ret;
if (flags & UART_CONFIG_TYPE) {
port->type = PORT_MSM;
......@@ -691,9 +649,6 @@ static void msm_config_port(struct uart_port *port, int flags)
if (ret)
return;
}
if (msm_port->gsbi_base)
writel_relaxed(GSBI_PROTOCOL_UART,
msm_port->gsbi_base + GSBI_CONTROL);
}
static int msm_verify_port(struct uart_port *port, struct serial_struct *ser)
......@@ -1110,6 +1065,7 @@ static struct of_device_id msm_match_table[] = {
static struct platform_driver msm_platform_driver = {
.remove = msm_serial_remove,
.probe = msm_serial_probe,
.driver = {
.name = "msm_serial",
.owner = THIS_MODULE,
......@@ -1125,7 +1081,7 @@ static int __init msm_serial_init(void)
if (unlikely(ret))
return ret;
ret = platform_driver_probe(&msm_platform_driver, msm_serial_probe);
ret = platform_driver_register(&msm_platform_driver);
if (unlikely(ret))
uart_unregister_driver(&msm_uart_driver);
......
......@@ -109,11 +109,6 @@
#define UART_ISR 0x0014
#define UART_ISR_TX_READY (1 << 7)
#define GSBI_CONTROL 0x0
#define GSBI_PROTOCOL_CODE 0x30
#define GSBI_PROTOCOL_UART 0x40
#define GSBI_PROTOCOL_IDLE 0x0
#define UARTDM_RXFS 0x50
#define UARTDM_RXFS_BUF_SHIFT 0x7
#define UARTDM_RXFS_BUF_MASK 0x7
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment