Merge branch 'cadence'

Boris BREZILLON says:

====================
net/cadence/macb: add support for dt phy definition

This patch series adds support for ethernet phy definition using device
tree.

This may help in moving some at91 boards to dt (some of them define an
interrupt pin).

Tested on samad31ek.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

arch/arm/boot/dts/sama5d3xmb.dtsi

@@ -81,6 +81,14 @@ &pinctrl_adc0_ad4
 
 			macb1: ethernet@f802c000 {
 				phy-mode = "rmii";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+				phy0: ethernet-phy@0 {
+					interrupt-parent = <&pioE>;
+					interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
+					reg = <1>;
+				};
 			};
 
 			pinctrl@fffff200 {

drivers/net/ethernet/cadence/macb.c

@@ -27,6 +27,7 @@
 #include <linux/phy.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include <linux/pinctrl/consumer.h>
 
@@ -314,6 +315,7 @@ static int macb_mii_probe(struct net_device *dev)
 int macb_mii_init(struct macb *bp)
 {
 	struct macb_platform_data *pdata;
+	struct device_node *np;
 	int err = -ENXIO, i;
 
 	/* Enable management port */
@@ -335,21 +337,46 @@ int macb_mii_init(struct macb *bp)
 	bp->mii_bus->parent = &bp->dev->dev;
 	pdata = bp->pdev->dev.platform_data;
 
-	if (pdata)
-		bp->mii_bus->phy_mask = pdata->phy_mask;
-
 	bp->mii_bus->irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL);
 	if (!bp->mii_bus->irq) {
 		err = -ENOMEM;
 		goto err_out_free_mdiobus;
 	}
 
+	dev_set_drvdata(&bp->dev->dev, bp->mii_bus);
+
+	np = bp->pdev->dev.of_node;
+	if (np) {
+		/* try dt phy registration */
+		err = of_mdiobus_register(bp->mii_bus, np);
+
+		/* fallback to standard phy registration if no phy were
+		   found during dt phy registration */
+		if (!err && !phy_find_first(bp->mii_bus)) {
+			for (i = 0; i < PHY_MAX_ADDR; i++) {
+				struct phy_device *phydev;
+
+				phydev = mdiobus_scan(bp->mii_bus, i);
+				if (IS_ERR(phydev)) {
+					err = PTR_ERR(phydev);
+					break;
+				}
+			}
+
+			if (err)
+				goto err_out_unregister_bus;
+		}
+	} else {
 		for (i = 0; i < PHY_MAX_ADDR; i++)
 			bp->mii_bus->irq[i] = PHY_POLL;
 
-	dev_set_drvdata(&bp->dev->dev, bp->mii_bus);
+		if (pdata)
+			bp->mii_bus->phy_mask = pdata->phy_mask;
 
-	if (mdiobus_register(bp->mii_bus))
+		err = mdiobus_register(bp->mii_bus);
+	}
+
+	if (err)
 		goto err_out_free_mdio_irq;
 
 	if (macb_mii_probe(bp->dev) != 0) {