Skip to content

L
linux
Commit b7df53b3 authored by Andrew Morton's avatar Andrew Morton Committed by Linus Torvalds
Browse files
Options

[PATCH] MIPS: New 2.6 serial drivers 

From: Ralf Baechle <ralf@linux-mips.org>

Three new MIPS-specific serial drivers.  ip22.c is derived from the sparc
zilog driver; guess we should write a generic Zilog driver somewhen ...
parent 95b387a4
Show whitespace changes
Inline Side-by-side
Showing with 3980 additions and 0 deletions
drivers/serial/Kconfig
View file @ b7df53b3
...@@ -256,6 +256,27 @@ config SERIAL_CLPS711X_OLD_NAME ...@@ -256,6 +256,27 @@ config SERIAL_CLPS711X_OLD_NAME
help help
::: To be written ::: ::: To be written :::
config SERIAL_DZ
bool "DECstation DZ serial driver"
depends on DECSTATION
select SERIAL_CORE
help
DZ11-family serial controllers for VAXstations, including the
DC7085, M7814, and M7819.
config SERIAL_DZ_CONSOLE
bool "Support console on DECstation DZ serial driver"
depends on SERIAL_DZ=y
select SERIAL_CORE_CONSOLE
help
If you say Y here, it will be possible to use a serial port as the
system console (the system console is the device which receives all
kernel messages and warnings and which allows logins in single user
mode). Note that the firmware uses ttyS0 as the serial console on
the Maxine and ttyS2 on the others.
If unsure, say Y.
config SERIAL_21285 config SERIAL_21285
tristate "DC21285 serial port support" tristate "DC21285 serial port support"
depends on ARM && FOOTBRIDGE depends on ARM && FOOTBRIDGE
...@@ -422,6 +443,20 @@ config SERIAL_SUNSAB_CONSOLE ...@@ -422,6 +443,20 @@ config SERIAL_SUNSAB_CONSOLE
on your Sparc system as the console, you can do so by answering on your Sparc system as the console, you can do so by answering
Y to this option. Y to this option.
config SERIAL_IP22_ZILOG
tristate "IP22 Zilog8530 serial support"
depends on SGI_IP22
select SERIAL_CORE
help
This driver supports the Zilog8530 serial ports found on SGI IP22
systems. Say Y or M if you want to be able to these serial ports.
config SERIAL_IP22_ZILOG_CONSOLE
bool "Console on IP22 Zilog8530 serial port"
depends on SERIAL_IP22_ZILOG=y
select SERIAL_CORE_CONSOLE
help
config V850E_UART config V850E_UART
bool "NEC V850E on-chip UART support" bool "NEC V850E on-chip UART support"
depends on V850E_MA1 || V850E_ME2 || V850E_TEG || V850E2_ANNA || V850E_AS85EP1 depends on V850E_MA1 || V850E_ME2 || V850E_TEG || V850E2_ANNA || V850E_AS85EP1
...@@ -451,6 +486,22 @@ config SERIAL98_CONSOLE ...@@ -451,6 +486,22 @@ config SERIAL98_CONSOLE
depends on SERIAL98=y depends on SERIAL98=y
select SERIAL_CORE_CONSOLE select SERIAL_CORE_CONSOLE
config SERIAL_AU1X00
bool "Enable Au1x00 UART Support"
depends on MIPS && SOC_AU1X00
select SERIAL_CORE
help
If you have an Alchemy AU1X00 processor (MIPS based) and you want
to use serial ports, say Y. Otherwise, say N.
config SERIAL_AU1X00_CONSOLE
bool "Enable Au1x00 serial console"
depends on SERIAL_AU1X00
select SERIAL_CORE_CONSOLE
help
If you have an Alchemy AU1X00 processor (MIPS based) and you want
to use a console on a serial port, say Y. Otherwise, say N.
config SERIAL_CORE config SERIAL_CORE
tristate tristate
......
drivers/serial/Makefile
View file @ b7df53b3
...@@ -23,6 +23,7 @@ obj-$(CONFIG_SERIAL_SA1100) += sa1100.o ...@@ -23,6 +23,7 @@ obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
obj-$(CONFIG_SERIAL_UART00) += uart00.o obj-$(CONFIG_SERIAL_UART00) += uart00.o
obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o
obj-$(CONFIG_SERIAL_SUNZILOG) += sunzilog.o obj-$(CONFIG_SERIAL_SUNZILOG) += sunzilog.o
obj-$(CONFIG_SERIAL_IP22_ZILOG) += ip22zilog.o
obj-$(CONFIG_SERIAL_SUNSU) += sunsu.o obj-$(CONFIG_SERIAL_SUNSU) += sunsu.o
obj-$(CONFIG_SERIAL_SUNSAB) += sunsab.o obj-$(CONFIG_SERIAL_SUNSAB) += sunsab.o
obj-$(CONFIG_SERIAL_MUX) += mux.o obj-$(CONFIG_SERIAL_MUX) += mux.o
...@@ -32,3 +33,5 @@ obj-$(CONFIG_SERIAL_COLDFIRE) += mcfserial.o ...@@ -32,3 +33,5 @@ obj-$(CONFIG_SERIAL_COLDFIRE) += mcfserial.o
obj-$(CONFIG_V850E_UART) += v850e_uart.o obj-$(CONFIG_V850E_UART) += v850e_uart.o
obj-$(CONFIG_SERIAL98) += serial98.o obj-$(CONFIG_SERIAL98) += serial98.o
obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o
obj-$(CONFIG_SERIAL_AU1X00) += au1x00_uart.o
obj-$(CONFIG_SERIAL_DZ) += dz.o
drivers/serial/au1x00_uart.c 0 → 100644
View file @ b7df53b3
/*
* Driver for 8250/16550-type serial ports
*
* Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
*
* Copyright (C) 2001 Russell King.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* A note about mapbase / membase
*
* mapbase is the physical address of the IO port. Currently, we don't
* support this very well, and it may well be dropped from this driver
* in future. As such, mapbase should be NULL.
*
* membase is an 'ioremapped' cookie. This is compatible with the old
* serial.c driver, and is currently the preferred form.
*/
#include <linux/config.h>
#include <linux/module.h>
#include <linux/tty.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/sysrq.h>
#include <linux/serial.h>
#include <linux/serialP.h>
#include <linux/delay.h>
#include <asm/serial.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-au1x00/au1000.h>
#if defined(CONFIG_SERIAL_AU1X00_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
#include <linux/serial_core.h>
#include "8250.h"
/*
* Debugging.
*/
#if 0
#define DEBUG_AUTOCONF(fmt...) printk(fmt)
#else
#define DEBUG_AUTOCONF(fmt...) do { } while (0)
#endif
#if 0
#define DEBUG_INTR(fmt...) printk(fmt)
#else
#define DEBUG_INTR(fmt...) do { } while (0)
#endif
#define PASS_LIMIT 256
/*
* We default to IRQ0 for the "no irq" hack. Some
* machine types want others as well - they're free
* to redefine this in their header file.
*/
#define is_real_interrupt(irq) ((irq) != 0)
static struct old_serial_port old_serial_port[] = {
{ .baud_base = 0,
.iomem_base = (u8 *)UART0_ADDR,
.irq = AU1000_UART0_INT,
.flags = STD_COM_FLAGS,
.iomem_reg_shift = 2,
}, {
.baud_base = 0,
.iomem_base = (u8 *)UART1_ADDR,
.irq = AU1000_UART1_INT,
.flags = STD_COM_FLAGS,
.iomem_reg_shift = 2
}, {
.baud_base = 0,
.iomem_base = (u8 *)UART2_ADDR,
.irq = AU1000_UART2_INT,
.flags = STD_COM_FLAGS,
.iomem_reg_shift = 2
}, {
.baud_base = 0,
.iomem_base = (u8 *)UART3_ADDR,
.irq = AU1000_UART3_INT,
.flags = STD_COM_FLAGS,
.iomem_reg_shift = 2
}
};
#define UART_NR ARRAY_SIZE(old_serial_port)
struct uart_8250_port {
struct uart_port port;
struct timer_list timer; /* "no irq" timer */
struct list_head list; /* ports on this IRQ */
unsigned short rev;
unsigned char acr;
unsigned char ier;
unsigned char lcr;
unsigned char mcr_mask; /* mask of user bits */
unsigned char mcr_force; /* mask of forced bits */
unsigned char lsr_break_flag;
/*
* We provide a per-port pm hook.
*/
void (*pm)(struct uart_port *port,
unsigned int state, unsigned int old);
};
struct irq_info {
spinlock_t lock;
struct list_head *head;
};
static struct irq_info irq_lists[NR_IRQS];
/*
* Here we define the default xmit fifo size used for each type of UART.
*/
static const struct serial_uart_config uart_config[PORT_MAX_8250+1] = {
{ "unknown", 1, 0 },
{ "8250", 1, 0 },
{ "16450", 1, 0 },
{ "16550", 1, 0 },
/* PORT_16550A */
{ "AU1X00_UART",16, UART_CLEAR_FIFO | UART_USE_FIFO },
};
static _INLINE_ unsigned int serial_in(struct uart_8250_port *up, int offset)
{
return au_readl((unsigned long)up->port.membase + offset);
}
static _INLINE_ void
serial_out(struct uart_8250_port *up, int offset, int value)
{
au_writel(value, (unsigned long)up->port.membase + offset);
}
#define serial_inp(up, offset) serial_in(up, offset)
#define serial_outp(up, offset, value) serial_out(up, offset, value)
/*
* This routine is called by rs_init() to initialize a specific serial
* port. It determines what type of UART chip this serial port is
* using: 8250, 16450, 16550, 16550A. The important question is
* whether or not this UART is a 16550A or not, since this will
* determine whether or not we can use its FIFO features or not.
*/
static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
{
unsigned char save_lcr, save_mcr;
unsigned long flags;
if (!up->port.iobase && !up->port.mapbase && !up->port.membase)
return;
DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04x, 0x%08lx): ",
up->port.line, up->port.iobase, up->port.membase);
/*
* We really do need global IRQs disabled here - we're going to
* be frobbing the chips IRQ enable register to see if it exists.
*/
spin_lock_irqsave(&up->port.lock, flags);
// save_flags(flags); cli();
save_mcr = serial_in(up, UART_MCR);
save_lcr = serial_in(up, UART_LCR);
up->port.type = PORT_16550A;
serial_outp(up, UART_LCR, save_lcr);
up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size;
if (up->port.type == PORT_UNKNOWN)
goto out;
/*
* Reset the UART.
*/
serial_outp(up, UART_MCR, save_mcr);
serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR |
UART_FCR_CLEAR_XMIT));
serial_outp(up, UART_FCR, 0);
(void)serial_in(up, UART_RX);
serial_outp(up, UART_IER, 0);
out:
spin_unlock_irqrestore(&up->port.lock, flags);
// restore_flags(flags);
DEBUG_AUTOCONF("type=%s\n", uart_config[up->port.type].name);
}
static void serial8250_stop_tx(struct uart_port *port, unsigned int tty_stop)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
if (up->ier & UART_IER_THRI) {
up->ier &= ~UART_IER_THRI;
serial_out(up, UART_IER, up->ier);
}
}
static void serial8250_start_tx(struct uart_port *port, unsigned int tty_start)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
if (!(up->ier & UART_IER_THRI)) {
up->ier |= UART_IER_THRI;
serial_out(up, UART_IER, up->ier);
}
}
static void serial8250_stop_rx(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
up->ier &= ~UART_IER_RLSI;
up->port.read_status_mask &= ~UART_LSR_DR;
serial_out(up, UART_IER, up->ier);
}
static void serial8250_enable_ms(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
}
static _INLINE_ void
receive_chars(struct uart_8250_port *up, int *status, struct pt_regs *regs)
{
struct tty_struct *tty = up->port.info->tty;
unsigned char ch;
int max_count = 256;
do {
if (unlikely(tty->flip.count >= TTY_FLIPBUF_SIZE)) {
tty->flip.work.func((void *)tty);
if (tty->flip.count >= TTY_FLIPBUF_SIZE)
return; // if TTY_DONT_FLIP is set
}
ch = serial_inp(up, UART_RX);
*tty->flip.char_buf_ptr = ch;
*tty->flip.flag_buf_ptr = TTY_NORMAL;
up->port.icount.rx++;
if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
UART_LSR_FE | UART_LSR_OE))) {
/*
* For statistics only
*/
if (*status & UART_LSR_BI) {
*status &= ~(UART_LSR_FE | UART_LSR_PE);
up->port.icount.brk++;
/*
* We do the SysRQ and SAK checking
* here because otherwise the break
* may get masked by ignore_status_mask
* or read_status_mask.
*/
if (uart_handle_break(&up->port))
goto ignore_char;
} else if (*status & UART_LSR_PE)
up->port.icount.parity++;
else if (*status & UART_LSR_FE)
up->port.icount.frame++;
if (*status & UART_LSR_OE)
up->port.icount.overrun++;
/*
* Mask off conditions which should be ingored.
*/
*status &= up->port.read_status_mask;
#ifdef CONFIG_SERIAL_AU1X00_CONSOLE
if (up->port.line == up->port.cons->index) {
/* Recover the break flag from console xmit */
*status |= up->lsr_break_flag;
up->lsr_break_flag = 0;
}
#endif
if (*status & UART_LSR_BI) {
DEBUG_INTR("handling break....");
*tty->flip.flag_buf_ptr = TTY_BREAK;
} else if (*status & UART_LSR_PE)
*tty->flip.flag_buf_ptr = TTY_PARITY;
else if (*status & UART_LSR_FE)
*tty->flip.flag_buf_ptr = TTY_FRAME;
}
if (uart_handle_sysrq_char(&up->port, ch, regs))
goto ignore_char;
if ((*status & up->port.ignore_status_mask) == 0) {
tty->flip.flag_buf_ptr++;
tty->flip.char_buf_ptr++;
tty->flip.count++;
}
if ((*status & UART_LSR_OE) &&
tty->flip.count < TTY_FLIPBUF_SIZE) {
/*
* Overrun is special, since it's reported
* immediately, and doesn't affect the current
* character.
*/
*tty->flip.flag_buf_ptr = TTY_OVERRUN;
tty->flip.flag_buf_ptr++;
tty->flip.char_buf_ptr++;
tty->flip.count++;
}
ignore_char:
*status = serial_inp(up, UART_LSR);
} while ((*status & UART_LSR_DR) && (max_count-- > 0));
tty_flip_buffer_push(tty);
}
static _INLINE_ void transmit_chars(struct uart_8250_port *up)
{
struct circ_buf *xmit = &up->port.info->xmit;
int count;
if (up->port.x_char) {
serial_outp(up, UART_TX, up->port.x_char);
up->port.icount.tx++;
up->port.x_char = 0;
return;
}
if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
serial8250_stop_tx(&up->port, 0);
return;
}
count = up->port.fifosize;
do {
serial_out(up, UART_TX, xmit->buf[xmit->tail]);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
up->port.icount.tx++;
if (uart_circ_empty(xmit))
break;
} while (--count > 0);
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&up->port);
DEBUG_INTR("THRE...");
if (uart_circ_empty(xmit))
serial8250_stop_tx(&up->port, 0);
}
static _INLINE_ void check_modem_status(struct uart_8250_port *up)
{
int status;
status = serial_in(up, UART_MSR);
if ((status & UART_MSR_ANY_DELTA) == 0)
return;
if (status & UART_MSR_TERI)
up->port.icount.rng++;
if (status & UART_MSR_DDSR)
up->port.icount.dsr++;
if (status & UART_MSR_DDCD)
uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
if (status & UART_MSR_DCTS)
uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
wake_up_interruptible(&up->port.info->delta_msr_wait);
}
/*
* This handles the interrupt from one port.
*/
static inline void
serial8250_handle_port(struct uart_8250_port *up, struct pt_regs *regs)
{
unsigned int status = serial_inp(up, UART_LSR);
DEBUG_INTR("status = %x...", status);
if (status & UART_LSR_DR)
receive_chars(up, &status, regs);
check_modem_status(up);
if (status & UART_LSR_THRE)
transmit_chars(up);
}
/*
* This is the serial driver's interrupt routine.
*
* Arjan thinks the old way was overly complex, so it got simplified.
* Alan disagrees, saying that need the complexity to handle the weird
* nature of ISA shared interrupts. (This is a special exception.)
*
* In order to handle ISA shared interrupts properly, we need to check
* that all ports have been serviced, and therefore the ISA interrupt
* line has been de-asserted.
*
* This means we need to loop through all ports. checking that they
* don't have an interrupt pending.
*/
static irqreturn_t serial8250_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
struct irq_info *i = dev_id;
struct list_head *l, *end = NULL;
int pass_counter = 0;
DEBUG_INTR("serial8250_interrupt(%d)...", irq);
spin_lock(&i->lock);
l = i->head;
do {
struct uart_8250_port *up;
unsigned int iir;
up = list_entry(l, struct uart_8250_port, list);
iir = serial_in(up, UART_IIR);
if (!(iir & UART_IIR_NO_INT)) {
spin_lock(&up->port.lock);
serial8250_handle_port(up, regs);
spin_unlock(&up->port.lock);
end = NULL;
} else if (end == NULL)
end = l;
l = l->next;
if (l == i->head && pass_counter++ > PASS_LIMIT) {
/* If we hit this, we're dead. */
printk(KERN_ERR "serial8250: too much work for "
"irq%d\n", irq);
break;
}
} while (l != end);
spin_unlock(&i->lock);
DEBUG_INTR("end.\n");
/* FIXME! Was it really ours? */
return IRQ_HANDLED;
}
/*
* To support ISA shared interrupts, we need to have one interrupt
* handler that ensures that the IRQ line has been deasserted
* before returning. Failing to do this will result in the IRQ
* line being stuck active, and, since ISA irqs are edge triggered,
* no more IRQs will be seen.
*/
static void serial_do_unlink(struct irq_info *i, struct uart_8250_port *up)
{
spin_lock_irq(&i->lock);
if (!list_empty(i->head)) {
if (i->head == &up->list)
i->head = i->head->next;
list_del(&up->list);
} else {
BUG_ON(i->head != &up->list);
i->head = NULL;
}
spin_unlock_irq(&i->lock);
}
static int serial_link_irq_chain(struct uart_8250_port *up)
{
struct irq_info *i = irq_lists + up->port.irq;
int ret, irq_flags = up->port.flags & UPF_SHARE_IRQ ? SA_SHIRQ : 0;
spin_lock_irq(&i->lock);
if (i->head) {
list_add(&up->list, i->head);
spin_unlock_irq(&i->lock);
ret = 0;
} else {
INIT_LIST_HEAD(&up->list);
i->head = &up->list;
spin_unlock_irq(&i->lock);
ret = request_irq(up->port.irq, serial8250_interrupt,
irq_flags, "serial", i);
if (ret < 0)
serial_do_unlink(i, up);
}
return ret;
}
static void serial_unlink_irq_chain(struct uart_8250_port *up)
{
struct irq_info *i = irq_lists + up->port.irq;
BUG_ON(i->head == NULL);
if (list_empty(i->head))
free_irq(up->port.irq, i);
serial_do_unlink(i, up);
}
/*
* This function is used to handle ports that do not have an
* interrupt. This doesn't work very well for 16450's, but gives
* barely passable results for a 16550A. (Although at the expense
* of much CPU overhead).
*/
static void serial8250_timeout(unsigned long data)
{
struct uart_8250_port *up = (struct uart_8250_port *)data;
unsigned int timeout;
unsigned int iir;
iir = serial_in(up, UART_IIR);
if (!(iir & UART_IIR_NO_INT)) {
spin_lock(&up->port.lock);
serial8250_handle_port(up, NULL);
spin_unlock(&up->port.lock);
}
timeout = up->port.timeout;
timeout = timeout > 6 ? (timeout / 2 - 2) : 1;
mod_timer(&up->timer, jiffies + timeout);
}
static unsigned int serial8250_tx_empty(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
unsigned long flags;
unsigned int ret;
spin_lock_irqsave(&up->port.lock, flags);
ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
spin_unlock_irqrestore(&up->port.lock, flags);
return ret;
}
static unsigned int serial8250_get_mctrl(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
unsigned long flags;
unsigned char status;
unsigned int ret;
spin_lock_irqsave(&up->port.lock, flags);
status = serial_in(up, UART_MSR);
spin_unlock_irqrestore(&up->port.lock, flags);
ret = 0;
if (status & UART_MSR_DCD)
ret |= TIOCM_CAR;
if (status & UART_MSR_RI)
ret |= TIOCM_RNG;
if (status & UART_MSR_DSR)
ret |= TIOCM_DSR;
if (status & UART_MSR_CTS)
ret |= TIOCM_CTS;
return ret;
}
static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
unsigned char mcr = 0;
if (mctrl & TIOCM_RTS)
mcr |= UART_MCR_RTS;
if (mctrl & TIOCM_DTR)
mcr |= UART_MCR_DTR;
if (mctrl & TIOCM_OUT1)
mcr |= UART_MCR_OUT1;
if (mctrl & TIOCM_OUT2)
mcr |= UART_MCR_OUT2;
if (mctrl & TIOCM_LOOP)
mcr |= UART_MCR_LOOP;
mcr = (mcr & up->mcr_mask) | up->mcr_force;
serial_out(up, UART_MCR, mcr);
}
static void serial8250_break_ctl(struct uart_port *port, int break_state)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
unsigned long flags;
spin_lock_irqsave(&up->port.lock, flags);
if (break_state == -1)
up->lcr |= UART_LCR_SBC;
else
up->lcr &= ~UART_LCR_SBC;
serial_out(up, UART_LCR, up->lcr);
spin_unlock_irqrestore(&up->port.lock, flags);
}
static int serial8250_startup(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
unsigned long flags;
int retval;
/*
* Clear the FIFO buffers and disable them.
* (they will be reeanbled in set_termios())
*/
if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) {
serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
serial_outp(up, UART_FCR, 0);
}
/*
* Clear the interrupt registers.
*/
(void) serial_inp(up, UART_LSR);
(void) serial_inp(up, UART_RX);
(void) serial_inp(up, UART_IIR);
(void) serial_inp(up, UART_MSR);
/*
* At this point, there's no way the LSR could still be 0xff;
* if it is, then bail out, because there's likely no UART
* here.
*/
if (!(up->port.flags & UPF_BUGGY_UART) &&
(serial_inp(up, UART_LSR) == 0xff)) {
printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
return -ENODEV;
}
retval = serial_link_irq_chain(up);
if (retval)
return retval;
/*
* Now, initialize the UART
*/
serial_outp(up, UART_LCR, UART_LCR_WLEN8);
spin_lock_irqsave(&up->port.lock, flags);
if (up->port.flags & UPF_FOURPORT) {
if (!is_real_interrupt(up->port.irq))
up->port.mctrl |= TIOCM_OUT1;
} else
/*
* Most PC uarts need OUT2 raised to enable interrupts.
*/
if (is_real_interrupt(up->port.irq))
up->port.mctrl |= TIOCM_OUT2;
serial8250_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
/*
* Finally, enable interrupts. Note: Modem status interrupts
* are set via set_termios(), which will be occurring imminently
* anyway, so we don't enable them here.
*/
up->ier = UART_IER_RLSI | UART_IER_RDI;
serial_outp(up, UART_IER, up->ier);
if (up->port.flags & UPF_FOURPORT) {
unsigned int icp;
/*
* Enable interrupts on the AST Fourport board
*/
icp = (up->port.iobase & 0xfe0) | 0x01f;
outb_p(0x80, icp);
(void) inb_p(icp);
}
/*
* And clear the interrupt registers again for luck.
*/
(void) serial_inp(up, UART_LSR);
(void) serial_inp(up, UART_RX);
(void) serial_inp(up, UART_IIR);
(void) serial_inp(up, UART_MSR);
return 0;
}
static void serial8250_shutdown(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
unsigned long flags;
/*
* Disable interrupts from this port
*/
up->ier = 0;
serial_outp(up, UART_IER, 0);
spin_lock_irqsave(&up->port.lock, flags);
if (up->port.flags & UPF_FOURPORT) {
/* reset interrupts on the AST Fourport board */
inb((up->port.iobase & 0xfe0) | 0x1f);
up->port.mctrl |= TIOCM_OUT1;
} else
up->port.mctrl &= ~TIOCM_OUT2;
serial8250_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
/*
* Disable break condition and FIFOs
*/
serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC);
serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR |
UART_FCR_CLEAR_XMIT);
serial_outp(up, UART_FCR, 0);
/*
* Read data port to reset things, and then unlink from
* the IRQ chain.
*/
(void) serial_in(up, UART_RX);
if (!is_real_interrupt(up->port.irq))
del_timer_sync(&up->timer);
else
serial_unlink_irq_chain(up);
}
static unsigned int serial8250_get_divisor(struct uart_port *port, unsigned int baud)
{
unsigned int quot;
/*
* Handle magic divisors for baud rates above baud_base on
* SMSC SuperIO chips.
*/
if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
baud == (port->uartclk/4))
quot = 0x8001;
else if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
baud == (port->uartclk/8))
quot = 0x8002;
else
quot = uart_get_divisor(port, baud);
return quot;
}
static void
serial8250_set_termios(struct uart_port *port, struct termios *termios,
struct termios *old)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
unsigned char cval, fcr = 0;
unsigned long flags;
unsigned int baud, quot;
switch (termios->c_cflag & CSIZE) {
case CS5:
cval = 0x00;
break;
case CS6:
cval = 0x01;
break;
case CS7:
cval = 0x02;
break;
default:
case CS8:
cval = 0x03;
break;
}
if (termios->c_cflag & CSTOPB)
cval |= 0x04;
if (termios->c_cflag & PARENB)
cval |= UART_LCR_PARITY;
if (!(termios->c_cflag & PARODD))
cval |= UART_LCR_EPAR;
#ifdef CMSPAR
if (termios->c_cflag & CMSPAR)
cval |= UART_LCR_SPAR;
#endif
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = serial8250_get_divisor(port, baud);
quot = 0x35; /* FIXME */
/*
* Work around a bug in the Oxford Semiconductor 952 rev B
* chip which causes it to seriously miscalculate baud rates
* when DLL is 0.
*/
if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 &&
up->rev == 0x5201)
quot ++;
if (uart_config[up->port.type].flags & UART_USE_FIFO) {
if (baud < 2400)
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIGGER_1;
else
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIGGER_8;
}
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
spin_lock_irqsave(&up->port.lock, flags);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (termios->c_iflag & INPCK)
up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= UART_LSR_BI;
/*
* Characteres to ignore
*/
up->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (termios->c_iflag & IGNBRK) {
up->port.ignore_status_mask |= UART_LSR_BI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_OE;
}
/*
* ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
up->port.ignore_status_mask |= UART_LSR_DR;
/*
* CTS flow control flag and modem status interrupts
*/
up->ier &= ~UART_IER_MSI;
if (UART_ENABLE_MS(&up->port, termios->c_cflag))
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
serial_outp(up, 0x28, quot & 0xffff);
up->lcr = cval; /* Save LCR */
if (up->port.type != PORT_16750) {
if (fcr & UART_FCR_ENABLE_FIFO) {
/* emulated UARTs (Lucent Venus 167x) need two steps */
serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
}
serial_outp(up, UART_FCR, fcr); /* set fcr */
}
spin_unlock_irqrestore(&up->port.lock, flags);
}
static void
serial8250_pm(struct uart_port *port, unsigned int state,
unsigned int oldstate)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
if (state) {
/* sleep */
if (up->pm)
up->pm(port, state, oldstate);
} else {
/* wake */
if (up->pm)
up->pm(port, state, oldstate);
}
}
/*
* Resource handling. This is complicated by the fact that resources
* depend on the port type. Maybe we should be claiming the standard
* 8250 ports, and then trying to get other resources as necessary?
*/
static int
serial8250_request_std_resource(struct uart_8250_port *up, struct resource **res)
{
unsigned int size = 8 << up->port.regshift;
int ret = 0;
switch (up->port.iotype) {
case SERIAL_IO_MEM:
if (up->port.mapbase) {
*res = request_mem_region(up->port.mapbase, size, "serial");
if (!*res)
ret = -EBUSY;
}
break;
case SERIAL_IO_HUB6:
case SERIAL_IO_PORT:
*res = request_region(up->port.iobase, size, "serial");
if (!*res)
ret = -EBUSY;
break;
}
return ret;
}
static void serial8250_release_port(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
unsigned long start, offset = 0, size = 0;
size <<= up->port.regshift;
switch (up->port.iotype) {
case SERIAL_IO_MEM:
if (up->port.mapbase) {
/*
* Unmap the area.
*/
iounmap(up->port.membase);
up->port.membase = NULL;
start = up->port.mapbase;
if (size)
release_mem_region(start + offset, size);
release_mem_region(start, 8 << up->port.regshift);
}
break;
case SERIAL_IO_HUB6:
case SERIAL_IO_PORT:
start = up->port.iobase;
if (size)
release_region(start + offset, size);
release_region(start + offset, 8 << up->port.regshift);
break;
default:
break;
}
}
static int serial8250_request_port(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
struct resource *res = NULL, *res_rsa = NULL;
int ret = 0;
if (up->port.flags & UPF_RESOURCES) {
ret = serial8250_request_std_resource(up, &res);
}
/*
* If we have a mapbase, then request that as well.
*/
if (ret == 0 && up->port.flags & UPF_IOREMAP) {
int size = res->end - res->start + 1;
up->port.membase = ioremap(up->port.mapbase, size);
if (!up->port.membase)
ret = -ENOMEM;
}
if (ret < 0) {
if (res_rsa)
release_resource(res_rsa);
if (res)
release_resource(res);
}
return ret;
}
static void serial8250_config_port(struct uart_port *port, int flags)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
struct resource *res_std = NULL, *res_rsa = NULL;
int probeflags = PROBE_ANY;
probeflags &= ~PROBE_RSA;
if (flags & UART_CONFIG_TYPE)
autoconfig(up, probeflags);
/*
* If the port wasn't an RSA port, release the resource.
*/
if (up->port.type != PORT_RSA && res_rsa)
release_resource(res_rsa);
if (up->port.type == PORT_UNKNOWN && res_std)
release_resource(res_std);
}
static int
serial8250_verify_port(struct uart_port *port, struct serial_struct *ser)
{
if (ser->irq >= NR_IRQS || ser->irq < 0 ||
ser->baud_base < 9600 || ser->type < PORT_UNKNOWN ||
ser->type > PORT_MAX_8250 || ser->type == PORT_CIRRUS ||
ser->type == PORT_STARTECH)
return -EINVAL;
return 0;
}
static const char *
serial8250_type(struct uart_port *port)
{
int type = port->type;
if (type >= ARRAY_SIZE(uart_config))
type = 0;
return uart_config[type].name;
}
static struct uart_ops serial8250_pops = {
.tx_empty = serial8250_tx_empty,
.set_mctrl = serial8250_set_mctrl,
.get_mctrl = serial8250_get_mctrl,
.stop_tx = serial8250_stop_tx,
.start_tx = serial8250_start_tx,
.stop_rx = serial8250_stop_rx,
.enable_ms = serial8250_enable_ms,
.break_ctl = serial8250_break_ctl,
.startup = serial8250_startup,
.shutdown = serial8250_shutdown,
.set_termios = serial8250_set_termios,
.pm = serial8250_pm,
.type = serial8250_type,
.release_port = serial8250_release_port,
.request_port = serial8250_request_port,
.config_port = serial8250_config_port,
.verify_port = serial8250_verify_port,
};
static struct uart_8250_port serial8250_ports[UART_NR];
static void __init serial8250_isa_init_ports(void)
{
struct uart_8250_port *up;
static int first = 1;
int i;
if (!first)
return;
first = 0;
for (i = 0, up = serial8250_ports; i < ARRAY_SIZE(old_serial_port);
i++, up++) {
up->port.iobase = old_serial_port[i].port;
up->port.irq = old_serial_port[i].irq;
up->port.uartclk = get_au1x00_uart_baud_base();
up->port.flags = old_serial_port[i].flags |
UPF_RESOURCES;
up->port.hub6 = old_serial_port[i].hub6;
up->port.membase = old_serial_port[i].iomem_base;
up->port.iotype = old_serial_port[i].io_type;
up->port.regshift = old_serial_port[i].iomem_reg_shift;
up->port.ops = &serial8250_pops;
}
}
static void __init serial8250_register_ports(struct uart_driver *drv)
{
int i;
serial8250_isa_init_ports();
for (i = 0; i < UART_NR; i++) {
struct uart_8250_port *up = &serial8250_ports[i];
up->port.line = i;
up->port.ops = &serial8250_pops;
init_timer(&up->timer);
up->timer.function = serial8250_timeout;
/*
* ALPHA_KLUDGE_MCR needs to be killed.
*/
up->mcr_mask = ~ALPHA_KLUDGE_MCR;
up->mcr_force = ALPHA_KLUDGE_MCR;
uart_add_one_port(drv, &up->port);
}
}
#ifdef CONFIG_SERIAL_AU1X00_CONSOLE
#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
/*
* Wait for transmitter & holding register to empty
*/
static inline void wait_for_xmitr(struct uart_8250_port *up)
{
unsigned int status, tmout = 10000;
/* Wait up to 10ms for the character(s) to be sent. */
do {
status = serial_in(up, UART_LSR);
if (status & UART_LSR_BI)
up->lsr_break_flag = UART_LSR_BI;
if (--tmout == 0)
break;
udelay(1);
} while ((status & BOTH_EMPTY) != BOTH_EMPTY);
/* Wait up to 1s for flow control if necessary */
if (up->port.flags & UPF_CONS_FLOW) {
tmout = 1000000;
while (--tmout &&
((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
udelay(1);
}
}
/*
* Print a string to the serial port trying not to disturb
* any possible real use of the port...
*
* The console_lock must be held when we get here.
*/
static void
serial8250_console_write(struct console *co, const char *s, unsigned int count)
{
struct uart_8250_port *up = &serial8250_ports[co->index];
unsigned int ier;
int i;
/*
* First save the UER then disable the interrupts
*/
ier = serial_in(up, UART_IER);
serial_out(up, UART_IER, 0);
/*
* Now, do each character
*/
for (i = 0; i < count; i++, s++) {
wait_for_xmitr(up);
/*
* Send the character out.
* If a LF, also do CR...
*/
serial_out(up, UART_TX, *s);
if (*s == 10) {
wait_for_xmitr(up);
serial_out(up, UART_TX, 13);
}
}
/*
* Finally, wait for transmitter to become empty
* and restore the IER
*/
wait_for_xmitr(up);
serial_out(up, UART_IER, ier);
}
static int __init serial8250_console_setup(struct console *co, char *options)
{
struct uart_port *port;
int baud = 9600;
int bits = 8;
int parity = 'n';
int flow = 'n';
/*
* Check whether an invalid uart number has been specified, and
* if so, search for the first available port that does have
* console support.
*/
if (co->index >= UART_NR)
co->index = 0;
port = &serial8250_ports[co->index].port;
/*
* Temporary fix.
*/
spin_lock_init(&port->lock);
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
return uart_set_options(port, co, baud, parity, bits, flow);
}
extern struct uart_driver serial8250_reg;
static struct console serial8250_console = {
.name = "ttyS",
.write = serial8250_console_write,
.device = uart_console_device,
.setup = serial8250_console_setup,
.flags = CON_PRINTBUFFER,
.index = -1,
.data = &serial8250_reg,
};
static int __init serial8250_console_init(void)
{
serial8250_isa_init_ports();
register_console(&serial8250_console);
return 0;
}
console_initcall(serial8250_console_init);
#define SERIAL8250_CONSOLE &serial8250_console
#else
#define SERIAL8250_CONSOLE NULL
#endif
static struct uart_driver serial8250_reg = {
.owner = THIS_MODULE,
.driver_name = "serial",
.devfs_name = "tts/",
.dev_name = "ttyS",
.major = TTY_MAJOR,
.minor = 64,
.nr = UART_NR,
.cons = SERIAL8250_CONSOLE,
};
/*
* register_serial and unregister_serial allows for 16x50 serial ports to be
* configured at run-time, to support PCMCIA modems.
*/
static int __register_serial(struct serial_struct *req, int line)
{
struct uart_port port;
port.iobase = req->port;
port.membase = req->iomem_base;
port.irq = req->irq;
port.uartclk = req->baud_base * 16;
port.fifosize = req->xmit_fifo_size;
port.regshift = req->iomem_reg_shift;
port.iotype = req->io_type;
port.flags = req->flags | UPF_BOOT_AUTOCONF;
port.mapbase = req->iomap_base;
port.line = line;
if (HIGH_BITS_OFFSET)
port.iobase |= (long) req->port_high << HIGH_BITS_OFFSET;
/*
* If a clock rate wasn't specified by the low level
* driver, then default to the standard clock rate.
*/
if (port.uartclk == 0)
port.uartclk = BASE_BAUD * 16;
return uart_register_port(&serial8250_reg, &port);
}
/**
* register_serial - configure a 16x50 serial port at runtime
* @req: request structure
*
* Configure the serial port specified by the request. If the
* port exists and is in use an error is returned. If the port
* is not currently in the table it is added.
*
* The port is then probed and if necessary the IRQ is autodetected
* If this fails an error is returned.
*
* On success the port is ready to use and the line number is returned.
*/
int register_serial(struct serial_struct *req)
{
return __register_serial(req, -1);
}
int __init early_serial_setup(struct uart_port *port)
{
serial8250_isa_init_ports();
serial8250_ports[port->line].port = *port;
serial8250_ports[port->line].port.ops = &serial8250_pops;
return 0;
}
/**
* unregister_serial - remove a 16x50 serial port at runtime
* @line: serial line number
*
* Remove one serial port. This may be called from interrupt
* context.
*/
void unregister_serial(int line)
{
uart_unregister_port(&serial8250_reg, line);
}
/*
* This is for ISAPNP only.
*/
void serial8250_get_irq_map(unsigned int *map)
{
int i;
for (i = 0; i < UART_NR; i++) {
if (serial8250_ports[i].port.type != PORT_UNKNOWN &&
serial8250_ports[i].port.irq < 16)
*map |= 1 << serial8250_ports[i].port.irq;
}
}
/**
* serial8250_suspend_port - suspend one serial port
* @line: serial line number
* @level: the level of port suspension, as per uart_suspend_port
*
* Suspend one serial port.
*/
void serial8250_suspend_port(int line)
{
uart_suspend_port(&serial8250_reg, &serial8250_ports[line].port);
}
/**
* serial8250_resume_port - resume one serial port
* @line: serial line number
* @level: the level of port resumption, as per uart_resume_port
*
* Resume one serial port.
*/
void serial8250_resume_port(int line)
{
uart_resume_port(&serial8250_reg, &serial8250_ports[line].port);
}
static int __init serial8250_init(void)
{
int ret, i;
printk(KERN_INFO "Serial: Au1x00 driver\n");
for (i = 0; i < NR_IRQS; i++)
spin_lock_init(&irq_lists[i].lock);
ret = uart_register_driver(&serial8250_reg);
if (ret >= 0)
serial8250_register_ports(&serial8250_reg);
return ret;
}
static void __exit serial8250_exit(void)
{
int i;
for (i = 0; i < UART_NR; i++)
uart_remove_one_port(&serial8250_reg, &serial8250_ports[i].port);
uart_unregister_driver(&serial8250_reg);
}
module_init(serial8250_init);
module_exit(serial8250_exit);
EXPORT_SYMBOL(register_serial);
EXPORT_SYMBOL(unregister_serial);
EXPORT_SYMBOL(serial8250_get_irq_map);
EXPORT_SYMBOL(serial8250_suspend_port);
EXPORT_SYMBOL(serial8250_resume_port);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Au1x00 serial driver\n");
drivers/serial/dz.c 0 → 100644
View file @ b7df53b3
/*
* dz.c: Serial port driver for DECStations equiped
* with the DZ chipset.
*
* Copyright (C) 1998 Olivier A. D. Lebaillif
*
* Email: olivier.lebaillif@ifrsys.com
*
* [31-AUG-98] triemer
* Changed IRQ to use Harald's dec internals interrupts.h
* removed base_addr code - moving address assignment to setup.c
* Changed name of dz_init to rs_init to be consistent with tc code
* [13-NOV-98] triemer fixed code to receive characters
* after patches by harald to irq code.
* [09-JAN-99] triemer minor fix for schedule - due to removal of timeout
* field from "current" - somewhere between 2.1.121 and 2.1.131
Qua Jun 27 15:02:26 BRT 2001
* [27-JUN-2001] Arnaldo Carvalho de Melo <acme@conectiva.com.br> - cleanups
*
* Parts (C) 1999 David Airlie, airlied@linux.ie
* [07-SEP-99] Bugfixes
*
* [06-Jan-2002] Russell King <rmk@arm.linux.org.uk>
* Converted to new serial core
*/
#undef DEBUG_DZ
#include <linux/config.h>
#include <linux/module.h>
#include <linux/tty.h>
#include <linux/interrupt.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/serial.h>
#include <linux/serial_core.h>
#include <asm/bootinfo.h>
#include <asm/dec/interrupts.h>
#include <asm/dec/kn01.h>
#include <asm/dec/kn02.h>
#include <asm/dec/machtype.h>
#include <asm/dec/prom.h>
#include <asm/irq.h>
#include <asm/system.h>
#include <asm/uaccess.h>
#define CONSOLE_LINE (3) /* for definition of struct console */
#include "dz.h"
#define DZ_INTR_DEBUG 1
static char *dz_name = "DECstation DZ serial driver version ";
static char *dz_version = "1.02";
struct dz_port {
struct uart_port port;
unsigned int cflag;
};
static struct dz_port dz_ports[DZ_NB_PORT];
#ifdef DEBUG_DZ
/*
* debugging code to send out chars via prom
*/
static void debug_console(const char *s, int count)
{
unsigned i;
for (i = 0; i < count; i++) {
if (*s == 10)
prom_printf("%c", 13);
prom_printf("%c", *s++);
}
}
#endif
/*
* ------------------------------------------------------------
* dz_in () and dz_out ()
*
* These routines are used to access the registers of the DZ
* chip, hiding relocation differences between implementation.
* ------------------------------------------------------------
*/
static inline unsigned short dz_in(struct dz_port *dport, unsigned offset)
{
volatile unsigned short *addr =
(volatile unsigned short *) (dport->port.membase + offset);
return *addr;
}
static inline void dz_out(struct dz_port *dport, unsigned offset,
unsigned short value)
{
volatile unsigned short *addr =
(volatile unsigned short *) (dport->port.membase + offset);
*addr = value;
}
/*
* ------------------------------------------------------------
* rs_stop () and rs_start ()
*
* These routines are called before setting or resetting
* tty->stopped. They enable or disable transmitter interrupts,
* as necessary.
* ------------------------------------------------------------
*/
static void dz_stop_tx(struct uart_port *uport, unsigned int tty_stop)
{
struct dz_port *dport = (struct dz_port *)uport;
unsigned short tmp, mask = 1 << dport->port.line;
unsigned long flags;
spin_lock_irqsave(&dport->port.lock, flags);
tmp = dz_in(dport, DZ_TCR); /* read the TX flag */
tmp &= ~mask; /* clear the TX flag */
dz_out(dport, DZ_TCR, tmp);
spin_unlock_irqrestore(&dport->port.lock, flags);
}
static void dz_start_tx(struct uart_port *uport, unsigned int tty_start)
{
struct dz_port *dport = (struct dz_port *)uport;
unsigned short tmp, mask = 1 << dport->port.line;
unsigned long flags;
spin_lock_irqsave(&dport->port.lock, flags);
tmp = dz_in(dport, DZ_TCR); /* read the TX flag */
tmp |= mask; /* set the TX flag */
dz_out(dport, DZ_TCR, tmp);
spin_unlock_irqrestore(&dport->port.lock, flags);
}
static void dz_stop_rx(struct uart_port *uport)
{
struct dz_port *dport = (struct dz_port *)uport;
unsigned long flags;
spin_lock_irqsave(&dport->port.lock, flags);
dport->cflag &= ~DZ_CREAD;
dz_out(dport, DZ_LPR, dport->cflag);
spin_unlock_irqrestore(&dport->port.lock, flags);
}
static void dz_enable_ms(struct uart_port *port)
{
/* nothing to do */
}
/*
* ------------------------------------------------------------
* Here starts the interrupt handling routines. All of the
* following subroutines are declared as inline and are folded
* into dz_interrupt. They were separated out for readability's
* sake.
*
* Note: rs_interrupt() is a "fast" interrupt, which means that it
* runs with interrupts turned off. People who may want to modify
* rs_interrupt() should try to keep the interrupt handler as fast as
* possible. After you are done making modifications, it is not a bad
* idea to do:
*
* make drivers/serial/dz.s
*
* and look at the resulting assemble code in dz.s.
*
* ------------------------------------------------------------
*/
/*
* ------------------------------------------------------------
* receive_char ()
*
* This routine deals with inputs from any lines.
* ------------------------------------------------------------
*/
static inline void dz_receive_chars(struct dz_port *dport)
{
struct tty_struct *tty = NULL;
struct uart_icount *icount;
int ignore = 0;
unsigned short status, tmp;
unsigned char ch;
/* this code is going to be a problem...
the call to tty_flip_buffer is going to need
to be rethought...
*/
do {
status = dz_in(dport, DZ_RBUF);
/* punt so we don't get duplicate characters */
if (!(status & DZ_DVAL))
goto ignore_char;
ch = UCHAR(status); /* grab the char */
#if 0
if (info->is_console) {
if (ch == 0)
return; /* it's a break ... */
}
#endif
tty = dport->port.info->tty;/* now tty points to the proper dev */
icount = &dport->port.icount;
if (!tty)
break;
if (tty->flip.count >= TTY_FLIPBUF_SIZE)
break;
*tty->flip.char_buf_ptr = ch;
*tty->flip.flag_buf_ptr = 0;
icount->rx++;
/* keep track of the statistics */
if (status & (DZ_OERR | DZ_FERR | DZ_PERR)) {
if (status & DZ_PERR) /* parity error */
icount->parity++;
else if (status & DZ_FERR) /* frame error */
icount->frame++;
if (status & DZ_OERR) /* overrun error */
icount->overrun++;
/* check to see if we should ignore the character
and mask off conditions that should be ignored
*/
if (status & dport->port.ignore_status_mask) {
if (++ignore > 100)
break;
goto ignore_char;
}
/* mask off the error conditions we want to ignore */
tmp = status & dport->port.read_status_mask;
if (tmp & DZ_PERR) {
*tty->flip.flag_buf_ptr = TTY_PARITY;
#ifdef DEBUG_DZ
debug_console("PERR\n", 5);
#endif
} else if (tmp & DZ_FERR) {
*tty->flip.flag_buf_ptr = TTY_FRAME;
#ifdef DEBUG_DZ
debug_console("FERR\n", 5);
#endif
}
if (tmp & DZ_OERR) {
#ifdef DEBUG_DZ
debug_console("OERR\n", 5);
#endif
if (tty->flip.count < TTY_FLIPBUF_SIZE) {
tty->flip.count++;
tty->flip.flag_buf_ptr++;
tty->flip.char_buf_ptr++;
*tty->flip.flag_buf_ptr = TTY_OVERRUN;
}
}
}
tty->flip.flag_buf_ptr++;
tty->flip.char_buf_ptr++;
tty->flip.count++;
ignore_char:
} while (status & DZ_DVAL);
if (tty)
tty_flip_buffer_push(tty);
}
/*
* ------------------------------------------------------------
* transmit_char ()
*
* This routine deals with outputs to any lines.
* ------------------------------------------------------------
*/
static inline void dz_transmit_chars(struct dz_port *dport)
{
struct circ_buf *xmit = &dport->port.info->xmit;
unsigned char tmp;
if (dport->port.x_char) { /* XON/XOFF chars */
dz_out(dport, DZ_TDR, dport->port.x_char);
dport->port.icount.tx++;
dport->port.x_char = 0;
return;
}
/* if nothing to do or stopped or hardware stopped */
if (uart_circ_empty(xmit) || uart_tx_stopped(&dport->port)) {
dz_stop_tx(&dport->port, 0);
return;
}
/*
* if something to do ... (rember the dz has no output fifo so we go
* one char at a time :-<
*/
tmp = xmit->buf[xmit->tail];
xmit->tail = (xmit->tail + 1) & (DZ_XMIT_SIZE - 1);
dz_out(dport, DZ_TDR, tmp);
dport->port.icount.tx++;
if (uart_circ_chars_pending(xmit) < DZ_WAKEUP_CHARS)
uart_write_wakeup(&dport->port);
/* Are we done */
if (uart_circ_empty(xmit))
dz_stop_tx(&dport->port, 0);
}
/*
* ------------------------------------------------------------
* check_modem_status ()
*
* Only valid for the MODEM line duh !
* ------------------------------------------------------------
*/
static inline void check_modem_status(struct dz_port *dport)
{
unsigned short status;
/* if not ne modem line just return */
if (dport->port.line != DZ_MODEM)
return;
status = dz_in(dport, DZ_MSR);
/* it's easy, since DSR2 is the only bit in the register */
if (status)
dport->port.icount.dsr++;
}
/*
* ------------------------------------------------------------
* dz_interrupt ()
*
* this is the main interrupt routine for the DZ chip.
* It deals with the multiple ports.
* ------------------------------------------------------------
*/
static irqreturn_t dz_interrupt(int irq, void *dev, struct pt_regs *regs)
{
struct dz_port *dport;
unsigned short status;
/* get the reason why we just got an irq */
status = dz_in((struct dz_port *)dev, DZ_CSR);
dport = &dz_ports[LINE(status)];
if (status & DZ_RDONE)
dz_receive_chars(dport);
if (status & DZ_TRDY)
dz_transmit_chars(dport);
/* FIXME: what about check modem status??? --rmk */
return IRQ_HANDLED;
}
/*
* -------------------------------------------------------------------
* Here ends the DZ interrupt routines.
* -------------------------------------------------------------------
*/
static unsigned int dz_get_mctrl(struct uart_port *uport)
{
struct dz_port *dport = (struct dz_port *)uport;
unsigned int mctrl = TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
if (dport->port.line == DZ_MODEM) {
/*
* CHECKME: This is a guess from the other code... --rmk
*/
if (dz_in(dport, DZ_MSR) & DZ_MODEM_DSR)
mctrl &= ~TIOCM_DSR;
}
return mctrl;
}
static void dz_set_mctrl(struct uart_port *uport, unsigned int mctrl)
{
struct dz_port *dport = (struct dz_port *)uport;
unsigned short tmp;
if (dport->port.line == DZ_MODEM) {
tmp = dz_in(dport, DZ_TCR);
if (mctrl & TIOCM_DTR)
tmp &= ~DZ_MODEM_DTR;
else
tmp |= DZ_MODEM_DTR;
dz_out(dport, DZ_TCR, tmp);
}
}
/*
* -------------------------------------------------------------------
* startup ()
*
* various initialization tasks
* -------------------------------------------------------------------
*/
static int dz_startup(struct uart_port *uport)
{
struct dz_port *dport = (struct dz_port *)uport;
unsigned long flags;
unsigned short tmp;
/* The dz lines for the mouse/keyboard must be
* opened using their respective drivers.
*/
if ((dport->port.line == DZ_KEYBOARD) ||
(dport->port.line == DZ_MOUSE))
return -ENODEV;
spin_lock_irqsave(&dport->port.lock, flags);
/* enable the interrupt and the scanning */
tmp = dz_in(dport, DZ_CSR);
tmp |= DZ_RIE | DZ_TIE | DZ_MSE;
dz_out(dport, DZ_CSR, tmp);
spin_unlock_irqrestore(&dport->port.lock, flags);
return 0;
}
/*
* -------------------------------------------------------------------
* shutdown ()
*
* This routine will shutdown a serial port; interrupts are disabled, and
* DTR is dropped if the hangup on close termio flag is on.
* -------------------------------------------------------------------
*/
static void dz_shutdown(struct uart_port *uport)
{
dz_stop_tx(uport, 0);
}
/*
* get_lsr_info - get line status register info
*
* Purpose: Let user call ioctl() to get info when the UART physically
* is emptied. On bus types like RS485, the transmitter must
* release the bus after transmitting. This must be done when
* the transmit shift register is empty, not be done when the
* transmit holding register is empty. This functionality
* allows an RS485 driver to be written in user space.
*/
static unsigned int dz_tx_empty(struct uart_port *uport)
{
struct dz_port *dport = (struct dz_port *)uport;
unsigned short status = dz_in(dport, DZ_LPR);
/* FIXME: this appears to be obviously broken --rmk. */
return status ? TIOCSER_TEMT : 0;
}
static void dz_break_ctl(struct uart_port *uport, int break_state)
{
struct dz_port *dport = (struct dz_port *)uport;
unsigned long flags;
unsigned short tmp, mask = 1 << uport->line;
spin_lock_irqsave(&uport->lock, flags);
tmp = dz_in(dport, DZ_TCR);
if (break_state)
tmp |= mask;
else
tmp &= ~mask;
dz_out(dport, DZ_TCR, tmp);
spin_unlock_irqrestore(&uport->lock, flags);
}
static void dz_set_termios(struct uart_port *uport, struct termios *termios,
struct termios *old_termios)
{
struct dz_port *dport = (struct dz_port *)uport;
unsigned long flags;
unsigned int cflag, baud;
cflag = dport->port.line;
switch (termios->c_cflag & CSIZE) {
case CS5:
cflag |= DZ_CS5;
break;
case CS6:
cflag |= DZ_CS6;
break;
case CS7:
cflag |= DZ_CS7;
break;
case CS8:
default:
cflag |= DZ_CS8;
}
if (termios->c_cflag & CSTOPB)
cflag |= DZ_CSTOPB;
if (termios->c_cflag & PARENB)
cflag |= DZ_PARENB;
if (termios->c_cflag & PARODD)
cflag |= DZ_PARODD;
baud = uart_get_baud_rate(uport, termios, old_termios, 50, 9600);
switch (baud) {
case 50:
cflag |= DZ_B50;
break;
case 75:
cflag |= DZ_B75;
break;
case 110:
cflag |= DZ_B110;
break;
case 134:
cflag |= DZ_B134;
break;
case 150:
cflag |= DZ_B150;
break;
case 300:
cflag |= DZ_B300;
break;
case 600:
cflag |= DZ_B600;
break;
case 1200:
cflag |= DZ_B1200;
break;
case 1800:
cflag |= DZ_B1800;
break;
case 2000:
cflag |= DZ_B2000;
break;
case 2400:
cflag |= DZ_B2400;
break;
case 3600:
cflag |= DZ_B3600;
break;
case 4800:
cflag |= DZ_B4800;
break;
case 7200:
cflag |= DZ_B7200;
break;
case 9600:
default:
cflag |= DZ_B9600;
}
if (termios->c_cflag & CREAD)
cflag |= DZ_RXENAB;
spin_lock_irqsave(&dport->port.lock, flags);
dz_out(dport, DZ_LPR, cflag);
dport->cflag = cflag;
/* setup accept flag */
dport->port.read_status_mask = DZ_OERR;
if (termios->c_iflag & INPCK)
dport->port.read_status_mask |= DZ_FERR | DZ_PERR;
/* characters to ignore */
uport->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
dport->port.ignore_status_mask |= DZ_FERR | DZ_PERR;
spin_unlock_irqrestore(&dport->port.lock, flags);
}
static const char *dz_type(struct uart_port *port)
{
return "DZ";
}
static void dz_release_port(struct uart_port *port)
{
/* nothing to do */
}
static int dz_request_port(struct uart_port *port)
{
return 0;
}
static void dz_config_port(struct uart_port *port, int flags)
{
if (flags & UART_CONFIG_TYPE)
port->type = PORT_DZ;
}
/*
* verify the new serial_struct (for TIOCSSERIAL).
*/
static int dz_verify_port(struct uart_port *port, struct serial_struct *ser)
{
int ret = 0;
if (ser->type != PORT_UNKNOWN && ser->type != PORT_DZ)
ret = -EINVAL;
if (ser->irq != port->irq)
ret = -EINVAL;
return ret;
}
static struct uart_ops dz_ops = {
.tx_empty = dz_tx_empty,
.get_mctrl = dz_get_mctrl,
.set_mctrl = dz_set_mctrl,
.stop_tx = dz_stop_tx,
.start_tx = dz_start_tx,
.stop_rx = dz_stop_rx,
.enable_ms = dz_enable_ms,
.break_ctl = dz_break_ctl,
.startup = dz_startup,
.shutdown = dz_shutdown,
.set_termios = dz_set_termios,
.type = dz_type,
.release_port = dz_release_port,
.request_port = dz_request_port,
.config_port = dz_config_port,
.verify_port = dz_verify_port,
};
static void __init dz_init_ports(void)
{
static int first = 1;
struct dz_port *dport;
unsigned long base;
int i;
if (!first)
return;
first = 0;
if (mips_machtype == MACH_DS23100 ||
mips_machtype == MACH_DS5100)
base = (unsigned long) KN01_DZ11_BASE;
else
base = (unsigned long) KN02_DZ11_BASE;
for (i = 0, dport = dz_ports; i < DZ_NB_PORT; i++, dport++) {
spin_lock_init(&dport->port.lock);
dport->port.membase = (char *) base;
dport->port.iotype = SERIAL_IO_PORT;
dport->port.irq = dec_interrupt[DEC_IRQ_DZ11];
dport->port.line = i;
dport->port.fifosize = 1;
dport->port.ops = &dz_ops;
dport->port.flags = UPF_BOOT_AUTOCONF;
}
}
static void dz_reset(struct dz_port *dport)
{
dz_out(dport, DZ_CSR, DZ_CLR);
while (dz_in(dport, DZ_CSR) & DZ_CLR);
/* FIXME: cpu_relax? */
iob();
/* enable scanning */
dz_out(dport, DZ_CSR, DZ_MSE);
}
#ifdef CONFIG_SERIAL_DZ_CONSOLE
static void dz_console_put_char(struct dz_port *dport, unsigned char ch)
{
unsigned long flags;
int loops = 2500;
unsigned short tmp = ch;
/* this code sends stuff out to serial device - spinning its
wheels and waiting. */
spin_lock_irqsave(&dport->port.lock, flags);
/* spin our wheels */
while (((dz_in(dport, DZ_CSR) & DZ_TRDY) != DZ_TRDY) && loops--)
/* FIXME: cpu_relax, udelay? --rmk */
;
/* Actually transmit the character. */
dz_out(dport, DZ_TDR, tmp);
spin_unlock_irqrestore(&dport->port.lock, flags);
}
/*
* -------------------------------------------------------------------
* dz_console_print ()
*
* dz_console_print is registered for printk.
* The console must be locked when we get here.
* -------------------------------------------------------------------
*/
static void dz_console_print(struct console *cons,
const char *str,
unsigned int count)
{
struct dz_port *dport = &dz_ports[CONSOLE_LINE];
#ifdef DEBUG_DZ
prom_printf((char *) str);
#endif
while (count--) {
if (*str == '\n')
dz_console_put_char(dport, '\r');
dz_console_put_char(dport, *str++);
}
}
static int __init dz_console_setup(struct console *co, char *options)
{
struct dz_port *dport = &dz_ports[CONSOLE_LINE];
int baud = 9600;
int bits = 8;
int parity = 'n';
int flow = 'n';
int ret;
unsigned short mask, tmp;
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
dz_reset(dport);
ret = uart_set_options(&dport->port, co, baud, parity, bits, flow);
if (ret == 0) {
mask = 1 << dport->port.line;
tmp = dz_in(dport, DZ_TCR); /* read the TX flag */
if (!(tmp & mask)) {
tmp |= mask; /* set the TX flag */
dz_out(dport, DZ_TCR, tmp);
}
}
return ret;
}
static struct console dz_sercons =
{
.name = "ttyS",
.write = dz_console_print,
.device = uart_console_device,
.setup = dz_console_setup,
.flags = CON_CONSDEV | CON_PRINTBUFFER,
.index = CONSOLE_LINE,
};
void __init dz_serial_console_init(void)
{
dz_init_ports();
register_console(&dz_sercons);
}
#define SERIAL_DZ_CONSOLE &dz_sercons
#else
#define SERIAL_DZ_CONSOLE NULL
#endif /* CONFIG_SERIAL_DZ_CONSOLE */
static struct uart_driver dz_reg = {
.owner = THIS_MODULE,
.driver_name = "serial",
#ifdef CONFIG_DEVFS
.dev_name = "tts/%d",
#else
.dev_name = "ttyS%d",
#endif
.major = TTY_MAJOR,
.minor = 64,
.nr = DZ_NB_PORT,
.cons = SERIAL_DZ_CONSOLE,
};
int __init dz_init(void)
{
unsigned long flags;
int ret, i;
printk("%s%s\n", dz_name, dz_version);
dz_init_ports();
save_flags(flags);
cli();
#ifndef CONFIG_SERIAL_DZ_CONSOLE
/* reset the chip */
dz_reset(&dz_ports[0]);
#endif
/* order matters here... the trick is that flags
is updated... in request_irq - to immediatedly obliterate
it is unwise. */
restore_flags(flags);
if (request_irq(dz_ports[0].port.irq, dz_interrupt,
SA_INTERRUPT, "DZ", &dz_ports[0]))
panic("Unable to register DZ interrupt");
ret = uart_register_driver(&dz_reg);
if (ret != 0)
return ret;
for (i = 0; i < DZ_NB_PORT; i++)
uart_add_one_port(&dz_reg, &dz_ports[i].port);
return ret;
}
MODULE_DESCRIPTION("DECstation DZ serial driver");
MODULE_LICENSE("GPL");
drivers/serial/dz.h 0 → 100644
View file @ b7df53b3
/*
* dz.h: Serial port driver for DECStations equiped
* with the DZ chipset.
*
* Copyright (C) 1998 Olivier A. D. Lebaillif
*
* Email: olivier.lebaillif@ifrsys.com
*
*/
#ifndef DZ_SERIAL_H
#define DZ_SERIAL_H
/*
* Definitions for the Control and Status Received.
*/
#define DZ_TRDY 0x8000 /* Transmitter empty */
#define DZ_TIE 0x4000 /* Transmitter Interrupt Enable */
#define DZ_RDONE 0x0080 /* Receiver data ready */
#define DZ_RIE 0x0040 /* Receive Interrupt Enable */
#define DZ_MSE 0x0020 /* Master Scan Enable */
#define DZ_CLR 0x0010 /* Master reset */
#define DZ_MAINT 0x0008 /* Loop Back Mode */
/*
* Definitions for the Received buffer.
*/
#define DZ_RBUF_MASK 0x00FF /* Data Mask in the Receive Buffer */
#define DZ_LINE_MASK 0x0300 /* Line Mask in the Receive Buffer */
#define DZ_DVAL 0x8000 /* Valid Data indicator */
#define DZ_OERR 0x4000 /* Overrun error indicator */
#define DZ_FERR 0x2000 /* Frame error indicator */
#define DZ_PERR 0x1000 /* Parity error indicator */
#define LINE(x) (x & DZ_LINE_MASK) >> 8 /* Get the line number from the input buffer */
#define UCHAR(x) (unsigned char)(x & DZ_RBUF_MASK)
/*
* Definitions for the Transmit Register.
*/
#define DZ_LINE_KEYBOARD 0x0001
#define DZ_LINE_MOUSE 0x0002
#define DZ_LINE_MODEM 0x0004
#define DZ_LINE_PRINTER 0x0008
#define DZ_MODEM_DTR 0x0400 /* DTR for the modem line (2) */
/*
* Definitions for the Modem Status Register.
*/
#define DZ_MODEM_DSR 0x0200 /* DSR for the modem line (2) */
/*
* Definitions for the Transmit Data Register.
*/
#define DZ_BRK0 0x0100 /* Break assertion for line 0 */
#define DZ_BRK1 0x0200 /* Break assertion for line 1 */
#define DZ_BRK2 0x0400 /* Break assertion for line 2 */
#define DZ_BRK3 0x0800 /* Break assertion for line 3 */
/*
* Definitions for the Line Parameter Register.
*/
#define DZ_KEYBOARD 0x0000 /* line 0 = keyboard */
#define DZ_MOUSE 0x0001 /* line 1 = mouse */
#define DZ_MODEM 0x0002 /* line 2 = modem */
#define DZ_PRINTER 0x0003 /* line 3 = printer */
#define DZ_CSIZE 0x0018 /* Number of bits per byte (mask) */
#define DZ_CS5 0x0000 /* 5 bits per byte */
#define DZ_CS6 0x0008 /* 6 bits per byte */
#define DZ_CS7 0x0010 /* 7 bits per byte */
#define DZ_CS8 0x0018 /* 8 bits per byte */
#define DZ_CSTOPB 0x0020 /* 2 stop bits instead of one */
#define DZ_PARENB 0x0040 /* Parity enable */
#define DZ_PARODD 0x0080 /* Odd parity instead of even */
#define DZ_CBAUD 0x0E00 /* Baud Rate (mask) */
#define DZ_B50 0x0000
#define DZ_B75 0x0100
#define DZ_B110 0x0200
#define DZ_B134 0x0300
#define DZ_B150 0x0400
#define DZ_B300 0x0500
#define DZ_B600 0x0600
#define DZ_B1200 0x0700
#define DZ_B1800 0x0800
#define DZ_B2000 0x0900
#define DZ_B2400 0x0A00
#define DZ_B3600 0x0B00
#define DZ_B4800 0x0C00
#define DZ_B7200 0x0D00
#define DZ_B9600 0x0E00
#define DZ_CREAD 0x1000 /* Enable receiver */
#define DZ_RXENAB 0x1000 /* enable receive char */
/*
* Addresses for the DZ registers
*/
#define DZ_CSR 0x00 /* Control and Status Register */
#define DZ_RBUF 0x08 /* Receive Buffer */
#define DZ_LPR 0x08 /* Line Parameters Register */
#define DZ_TCR 0x10 /* Transmitter Control Register */
#define DZ_MSR 0x18 /* Modem Status Register */
#define DZ_TDR 0x18 /* Transmit Data Register */
#define DZ_NB_PORT 4
#define DZ_XMIT_SIZE 4096 /* buffer size */
#define DZ_WAKEUP_CHARS DZ_XMIT_SIZE/4
#ifdef MODULE
int init_module (void)
void cleanup_module (void)
#endif
#endif /* DZ_SERIAL_H */
drivers/serial/ip22zilog.c 0 → 100644
View file @ b7df53b3
/*
* Driver for Zilog serial chips found on SGI workstations and
* servers. This driver could actually be made more generic.
*
* This is based on the drivers/serial/sunzilog.c code as of 2.6.0-test7 and the
* old drivers/sgi/char/sgiserial.c code which itself is based of the original
* drivers/sbus/char/zs.c code. A lot of code has been simply moved over
* directly from there but much has been rewritten. Credits therefore go out
* to David S. Miller, Eddie C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell
* for their work there.
*
* Copyright (C) 2002 Ralf Baechle (ralf@linux-mips.org)
* Copyright (C) 2002 David S. Miller (davem@redhat.com)
*/
#include <linux/config.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/errno.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/major.h>
#include <linux/string.h>
#include <linux/ptrace.h>
#include <linux/ioport.h>
#include <linux/slab.h>
#include <linux/circ_buf.h>
#include <linux/serial.h>
#include <linux/sysrq.h>
#include <linux/console.h>
#include <linux/spinlock.h>
#include <linux/init.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/sgialib.h>
#include <asm/sgi/ioc.h>
#include <asm/sgi/hpc3.h>
#include <asm/sgi/ip22.h>
#if defined(CONFIG_SERIAL_IP22_ZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
#include <linux/serial_core.h>
#include "ip22zilog.h"
int ip22serial_current_minor = 64;
void ip22_do_break(void);
/*
* On IP22 we need to delay after register accesses but we do not need to
* flush writes.
*/
#define ZSDELAY() udelay(5)
#define ZSDELAY_LONG() udelay(20)
#define ZS_WSYNC(channel) do { } while (0)
#define NUM_IP22ZILOG 1
#define NUM_CHANNELS (NUM_IP22ZILOG * 2)
#define ZS_CLOCK 4915200 /* Zilog input clock rate. */
#define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */
/*
* We wrap our port structure around the generic uart_port.
*/
struct uart_ip22zilog_port {
struct uart_port port;
/* IRQ servicing chain. */
struct uart_ip22zilog_port *next;
/* Current values of Zilog write registers. */
unsigned char curregs[NUM_ZSREGS];
unsigned int flags;
#define IP22ZILOG_FLAG_IS_CONS 0x00000004
#define IP22ZILOG_FLAG_IS_KGDB 0x00000008
#define IP22ZILOG_FLAG_MODEM_STATUS 0x00000010
#define IP22ZILOG_FLAG_IS_CHANNEL_A 0x00000020
#define IP22ZILOG_FLAG_REGS_HELD 0x00000040
#define IP22ZILOG_FLAG_TX_STOPPED 0x00000080
#define IP22ZILOG_FLAG_TX_ACTIVE 0x00000100
unsigned int cflag;
/* L1-A keyboard break state. */
int kbd_id;
int l1_down;
unsigned char parity_mask;
unsigned char prev_status;
};
#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel *)((PORT)->membase))
#define UART_ZILOG(PORT) ((struct uart_ip22zilog_port *)(PORT))
#define IP22ZILOG_GET_CURR_REG(PORT, REGNUM) \
(UART_ZILOG(PORT)->curregs[REGNUM])
#define IP22ZILOG_SET_CURR_REG(PORT, REGNUM, REGVAL) \
((UART_ZILOG(PORT)->curregs[REGNUM]) = (REGVAL))
#define ZS_IS_CONS(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CONS)
#define ZS_IS_KGDB(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_KGDB)
#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & IP22ZILOG_FLAG_MODEM_STATUS)
#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CHANNEL_A)
#define ZS_REGS_HELD(UP) ((UP)->flags & IP22ZILOG_FLAG_REGS_HELD)
#define ZS_TX_STOPPED(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_STOPPED)
#define ZS_TX_ACTIVE(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_ACTIVE)
/* Reading and writing Zilog8530 registers. The delays are to make this
* driver work on the IP22 which needs a settling delay after each chip
* register access, other machines handle this in hardware via auxiliary
* flip-flops which implement the settle time we do in software.
*
* The port lock must be held and local IRQs must be disabled
* when {read,write}_zsreg is invoked.
*/
static unsigned char read_zsreg(struct zilog_channel *channel,
unsigned char reg)
{
unsigned char retval;
writeb(reg, &channel->control);
ZSDELAY();
retval = readb(&channel->control);
ZSDELAY();
return retval;
}
static void write_zsreg(struct zilog_channel *channel,
unsigned char reg, unsigned char value)
{
writeb(reg, &channel->control);
ZSDELAY();
writeb(value, &channel->control);
ZSDELAY();
}
static void ip22zilog_clear_fifo(struct zilog_channel *channel)
{
int i;
for (i = 0; i < 32; i++) {
unsigned char regval;
regval = readb(&channel->control);
ZSDELAY();
if (regval & Rx_CH_AV)
break;
regval = read_zsreg(channel, R1);
readb(&channel->data);
ZSDELAY();
if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) {
writeb(ERR_RES, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
}
}
}
/* This function must only be called when the TX is not busy. The UART
* port lock must be held and local interrupts disabled.
*/
static void __load_zsregs(struct zilog_channel *channel, unsigned char *regs)
{
int i;
/* Let pending transmits finish. */
for (i = 0; i < 1000; i++) {
unsigned char stat = read_zsreg(channel, R1);
if (stat & ALL_SNT)
break;
udelay(100);
}
writeb(ERR_RES, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
ip22zilog_clear_fifo(channel);
/* Disable all interrupts. */
write_zsreg(channel, R1,
regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
/* Set parity, sync config, stop bits, and clock divisor. */
write_zsreg(channel, R4, regs[R4]);
/* Set misc. TX/RX control bits. */
write_zsreg(channel, R10, regs[R10]);
/* Set TX/RX controls sans the enable bits. */
write_zsreg(channel, R3, regs[R3] & ~RxENAB);
write_zsreg(channel, R5, regs[R5] & ~TxENAB);
/* Synchronous mode config. */
write_zsreg(channel, R6, regs[R6]);
write_zsreg(channel, R7, regs[R7]);
/* Don't mess with the interrupt vector (R2, unused by us) and
* master interrupt control (R9). We make sure this is setup
* properly at probe time then never touch it again.
*/
/* Disable baud generator. */
write_zsreg(channel, R14, regs[R14] & ~BRENAB);
/* Clock mode control. */
write_zsreg(channel, R11, regs[R11]);
/* Lower and upper byte of baud rate generator divisor. */
write_zsreg(channel, R12, regs[R12]);
write_zsreg(channel, R13, regs[R13]);
/* Now rewrite R14, with BRENAB (if set). */
write_zsreg(channel, R14, regs[R14]);
/* External status interrupt control. */
write_zsreg(channel, R15, regs[R15]);
/* Reset external status interrupts. */
write_zsreg(channel, R0, RES_EXT_INT);
write_zsreg(channel, R0, RES_EXT_INT);
/* Rewrite R3/R5, this time without enables masked. */
write_zsreg(channel, R3, regs[R3]);
write_zsreg(channel, R5, regs[R5]);
/* Rewrite R1, this time without IRQ enabled masked. */
write_zsreg(channel, R1, regs[R1]);
}
/* Reprogram the Zilog channel HW registers with the copies found in the
* software state struct. If the transmitter is busy, we defer this update
* until the next TX complete interrupt. Else, we do it right now.
*
* The UART port lock must be held and local interrupts disabled.
*/
static void ip22zilog_maybe_update_regs(struct uart_ip22zilog_port *up,
struct zilog_channel *channel)
{
if (!ZS_REGS_HELD(up)) {
if (ZS_TX_ACTIVE(up)) {
up->flags |= IP22ZILOG_FLAG_REGS_HELD;
} else {
__load_zsregs(channel, up->curregs);
}
}
}
static void ip22zilog_receive_chars(struct uart_ip22zilog_port *up,
struct zilog_channel *channel,
struct pt_regs *regs)
{
struct tty_struct *tty = up->port.info->tty; /* XXX info==NULL? */
while (1) {
unsigned char ch, r1;
if (unlikely(tty->flip.count >= TTY_FLIPBUF_SIZE)) {
tty->flip.work.func((void *)tty);
if (tty->flip.count >= TTY_FLIPBUF_SIZE)
return; /* XXX Ignores SysRq when we need it most. Fix. */
}
r1 = read_zsreg(channel, R1);
if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
writeb(ERR_RES, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
}
ch = readb(&channel->control);
ZSDELAY();
/* This funny hack depends upon BRK_ABRT not interfering
* with the other bits we care about in R1.
*/
if (ch & BRK_ABRT)
r1 |= BRK_ABRT;
ch = readb(&channel->data);
ZSDELAY();
ch &= up->parity_mask;
if (ZS_IS_CONS(up) && (r1 & BRK_ABRT)) {
/* Wait for BREAK to deassert to avoid potentially
* confusing the PROM.
*/
while (1) {
ch = readb(&channel->control);
ZSDELAY();
if (!(ch & BRK_ABRT))
break;
}
ip22_do_break();
return;
}
/* A real serial line, record the character and status. */
*tty->flip.char_buf_ptr = ch;
*tty->flip.flag_buf_ptr = TTY_NORMAL;
up->port.icount.rx++;
if (r1 & (BRK_ABRT | PAR_ERR | Rx_OVR | CRC_ERR)) {
if (r1 & BRK_ABRT) {
r1 &= ~(PAR_ERR | CRC_ERR);
up->port.icount.brk++;
if (uart_handle_break(&up->port))
goto next_char;
}
else if (r1 & PAR_ERR)
up->port.icount.parity++;
else if (r1 & CRC_ERR)
up->port.icount.frame++;
if (r1 & Rx_OVR)
up->port.icount.overrun++;
r1 &= up->port.read_status_mask;
if (r1 & BRK_ABRT)
*tty->flip.flag_buf_ptr = TTY_BREAK;
else if (r1 & PAR_ERR)
*tty->flip.flag_buf_ptr = TTY_PARITY;
else if (r1 & CRC_ERR)
*tty->flip.flag_buf_ptr = TTY_FRAME;
}
if (uart_handle_sysrq_char(&up->port, ch, regs))
goto next_char;
if (up->port.ignore_status_mask == 0xff ||
(r1 & up->port.ignore_status_mask) == 0) {
tty->flip.flag_buf_ptr++;
tty->flip.char_buf_ptr++;
tty->flip.count++;
}
if ((r1 & Rx_OVR) &&
tty->flip.count < TTY_FLIPBUF_SIZE) {
*tty->flip.flag_buf_ptr = TTY_OVERRUN;
tty->flip.flag_buf_ptr++;
tty->flip.char_buf_ptr++;
tty->flip.count++;
}
next_char:
ch = readb(&channel->control);
ZSDELAY();
if (!(ch & Rx_CH_AV))
break;
}
tty_flip_buffer_push(tty);
}
static void ip22zilog_status_handle(struct uart_ip22zilog_port *up,
struct zilog_channel *channel,
struct pt_regs *regs)
{
unsigned char status;
status = readb(&channel->control);
ZSDELAY();
writeb(RES_EXT_INT, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
if (ZS_WANTS_MODEM_STATUS(up)) {
if (status & SYNC)
up->port.icount.dsr++;
/* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
* But it does not tell us which bit has changed, we have to keep
* track of this ourselves.
*/
if ((status & DCD) ^ up->prev_status)
uart_handle_dcd_change(&up->port,
(status & DCD));
if ((status & CTS) ^ up->prev_status)
uart_handle_cts_change(&up->port,
(status & CTS));
wake_up_interruptible(&up->port.info->delta_msr_wait);
}
up->prev_status = status;
}
static void ip22zilog_transmit_chars(struct uart_ip22zilog_port *up,
struct zilog_channel *channel)
{
struct circ_buf *xmit;
if (ZS_IS_CONS(up)) {
unsigned char status = readb(&channel->control);
ZSDELAY();
/* TX still busy? Just wait for the next TX done interrupt.
*
* It can occur because of how we do serial console writes. It would
* be nice to transmit console writes just like we normally would for
* a TTY line. (ie. buffered and TX interrupt driven). That is not
* easy because console writes cannot sleep. One solution might be
* to poll on enough port->xmit space becomming free. -DaveM
*/
if (!(status & Tx_BUF_EMP))
return;
}
up->flags &= ~IP22ZILOG_FLAG_TX_ACTIVE;
if (ZS_REGS_HELD(up)) {
__load_zsregs(channel, up->curregs);
up->flags &= ~IP22ZILOG_FLAG_REGS_HELD;
}
if (ZS_TX_STOPPED(up)) {
up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED;
goto ack_tx_int;
}
if (up->port.x_char) {
up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
writeb(up->port.x_char, &channel->data);
ZSDELAY();
ZS_WSYNC(channel);
up->port.icount.tx++;
up->port.x_char = 0;
return;
}
if (up->port.info == NULL)
goto ack_tx_int;
xmit = &up->port.info->xmit;
if (uart_circ_empty(xmit)) {
uart_write_wakeup(&up->port);
goto ack_tx_int;
}
if (uart_tx_stopped(&up->port))
goto ack_tx_int;
up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
writeb(xmit->buf[xmit->tail], &channel->data);
ZSDELAY();
ZS_WSYNC(channel);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
up->port.icount.tx++;
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&up->port);
return;
ack_tx_int:
writeb(RES_Tx_P, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
}
static irqreturn_t ip22zilog_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
struct uart_ip22zilog_port *up = dev_id;
while (up) {
struct zilog_channel *channel
= ZILOG_CHANNEL_FROM_PORT(&up->port);
unsigned char r3;
spin_lock(&up->port.lock);
r3 = read_zsreg(channel, R3);
/* Channel A */
if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
writeb(RES_H_IUS, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
if (r3 & CHARxIP)
ip22zilog_receive_chars(up, channel, regs);
if (r3 & CHAEXT)
ip22zilog_status_handle(up, channel, regs);
if (r3 & CHATxIP)
ip22zilog_transmit_chars(up, channel);
}
spin_unlock(&up->port.lock);
/* Channel B */
up = up->next;
channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
spin_lock(&up->port.lock);
if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
writeb(RES_H_IUS, &channel->control);
ZSDELAY();
ZS_WSYNC(channel);
if (r3 & CHBRxIP)
ip22zilog_receive_chars(up, channel, regs);
if (r3 & CHBEXT)
ip22zilog_status_handle(up, channel, regs);
if (r3 & CHBTxIP)
ip22zilog_transmit_chars(up, channel);
}
spin_unlock(&up->port.lock);
up = up->next;
}
return IRQ_HANDLED;
}
/* A convenient way to quickly get R0 status. The caller must _not_ hold the
* port lock, it is acquired here.
*/
static __inline__ unsigned char ip22zilog_read_channel_status(struct uart_port *port)
{
struct zilog_channel *channel;
unsigned long flags;
unsigned char status;
spin_lock_irqsave(&port->lock, flags);
channel = ZILOG_CHANNEL_FROM_PORT(port);
status = readb(&channel->control);
ZSDELAY();
spin_unlock_irqrestore(&port->lock, flags);
return status;
}
/* The port lock is not held. */
static unsigned int ip22zilog_tx_empty(struct uart_port *port)
{
unsigned char status;
unsigned int ret;
status = ip22zilog_read_channel_status(port);
if (status & Tx_BUF_EMP)
ret = TIOCSER_TEMT;
else
ret = 0;
return ret;
}
/* The port lock is not held. */
static unsigned int ip22zilog_get_mctrl(struct uart_port *port)
{
unsigned char status;
unsigned int ret;
status = ip22zilog_read_channel_status(port);
ret = 0;
if (status & DCD)
ret |= TIOCM_CAR;
if (status & SYNC)
ret |= TIOCM_DSR;
if (status & CTS)
ret |= TIOCM_CTS;
return ret;
}
/* The port lock is held and interrupts are disabled. */
static void ip22zilog_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
unsigned char set_bits, clear_bits;
set_bits = clear_bits = 0;
if (mctrl & TIOCM_RTS)
set_bits |= RTS;
else
clear_bits |= RTS;
if (mctrl & TIOCM_DTR)
set_bits |= DTR;
else
clear_bits |= DTR;
/* NOTE: Not subject to 'transmitter active' rule. */
up->curregs[R5] |= set_bits;
up->curregs[R5] &= ~clear_bits;
write_zsreg(channel, R5, up->curregs[R5]);
}
/* The port lock is held and interrupts are disabled. */
static void ip22zilog_stop_tx(struct uart_port *port, unsigned int tty_stop)
{
struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
up->flags |= IP22ZILOG_FLAG_TX_STOPPED;
}
/* The port lock is held and interrupts are disabled. */
static void ip22zilog_start_tx(struct uart_port *port, unsigned int tty_start)
{
struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
unsigned char status;
up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED;
status = readb(&channel->control);
ZSDELAY();
/* TX busy? Just wait for the TX done interrupt. */
if (!(status & Tx_BUF_EMP))
return;
/* Send the first character to jump-start the TX done
* IRQ sending engine.
*/
if (port->x_char) {
writeb(port->x_char, &channel->data);
ZSDELAY();
ZS_WSYNC(channel);
port->icount.tx++;
port->x_char = 0;
} else {
struct circ_buf *xmit = &port->info->xmit;
writeb(xmit->buf[xmit->tail], &channel->data);
ZSDELAY();
ZS_WSYNC(channel);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
port->icount.tx++;
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&up->port);
}
}
/* The port lock is not held. */
static void ip22zilog_stop_rx(struct uart_port *port)
{
struct uart_ip22zilog_port *up = UART_ZILOG(port);
struct zilog_channel *channel;
unsigned long flags;
if (ZS_IS_CONS(up))
return;
spin_lock_irqsave(&port->lock, flags);
channel = ZILOG_CHANNEL_FROM_PORT(port);
/* Disable all RX interrupts. */
up->curregs[R1] &= ~RxINT_MASK;
ip22zilog_maybe_update_regs(up, channel);
spin_unlock_irqrestore(&port->lock, flags);
}
/* The port lock is not held. */
static void ip22zilog_enable_ms(struct uart_port *port)
{
struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
unsigned char new_reg;
unsigned long flags;
spin_lock_irqsave(&port->lock, flags);
new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
if (new_reg != up->curregs[R15]) {
up->curregs[R15] = new_reg;
/* NOTE: Not subject to 'transmitter active' rule. */
write_zsreg(channel, R15, up->curregs[R15]);
}
spin_unlock_irqrestore(&port->lock, flags);
}
/* The port lock is not held. */
static void ip22zilog_break_ctl(struct uart_port *port, int break_state)
{
struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
unsigned char set_bits, clear_bits, new_reg;
unsigned long flags;
set_bits = clear_bits = 0;
if (break_state)
set_bits |= SND_BRK;
else
clear_bits |= SND_BRK;
spin_lock_irqsave(&port->lock, flags);
new_reg = (up->curregs[R5] | set_bits) & ~clear_bits;
if (new_reg != up->curregs[R5]) {
up->curregs[R5] = new_reg;
/* NOTE: Not subject to 'transmitter active' rule. */
write_zsreg(channel, R5, up->curregs[R5]);
}
spin_unlock_irqrestore(&port->lock, flags);
}
static void __ip22zilog_startup(struct uart_ip22zilog_port *up)
{
struct zilog_channel *channel;
channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
up->prev_status = readb(&channel->control);
/* Enable receiver and transmitter. */
up->curregs[R3] |= RxENAB;
up->curregs[R5] |= TxENAB;
up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
ip22zilog_maybe_update_regs(up, channel);
}
static int ip22zilog_startup(struct uart_port *port)
{
struct uart_ip22zilog_port *up = UART_ZILOG(port);
unsigned long flags;
if (ZS_IS_CONS(up))
return 0;
spin_lock_irqsave(&port->lock, flags);
__ip22zilog_startup(up);
spin_unlock_irqrestore(&port->lock, flags);
return 0;
}
/*
* The test for ZS_IS_CONS is explained by the following e-mail:
*****
* From: Russell King <rmk@arm.linux.org.uk>
* Date: Sun, 8 Dec 2002 10:18:38 +0000
*
* On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote:
* > I boot my 2.5 boxes using "console=ttyS0,9600" argument,
* > and I noticed that something is not right with reference
* > counting in this case. It seems that when the console
* > is open by kernel initially, this is not accounted
* > as an open, and uart_startup is not called.
*
* That is correct. We are unable to call uart_startup when the serial
* console is initialised because it may need to allocate memory (as
* request_irq does) and the memory allocators may not have been
* initialised.
*
* 1. initialise the port into a state where it can send characters in the
* console write method.
*
* 2. don't do the actual hardware shutdown in your shutdown() method (but
* do the normal software shutdown - ie, free irqs etc)
*****
*/
static void ip22zilog_shutdown(struct uart_port *port)
{
struct uart_ip22zilog_port *up = UART_ZILOG(port);
struct zilog_channel *channel;
unsigned long flags;
if (ZS_IS_CONS(up))
return;
spin_lock_irqsave(&port->lock, flags);
channel = ZILOG_CHANNEL_FROM_PORT(port);
/* Disable receiver and transmitter. */
up->curregs[R3] &= ~RxENAB;
up->curregs[R5] &= ~TxENAB;
/* Disable all interrupts and BRK assertion. */
up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
up->curregs[R5] &= ~SND_BRK;
ip22zilog_maybe_update_regs(up, channel);
spin_unlock_irqrestore(&port->lock, flags);
}
/* Shared by TTY driver and serial console setup. The port lock is held
* and local interrupts are disabled.
*/
static void
ip22zilog_convert_to_zs(struct uart_ip22zilog_port *up, unsigned int cflag,
unsigned int iflag, int brg)
{
up->curregs[R10] = NRZ;
up->curregs[R11] = TCBR | RCBR;
/* Program BAUD and clock source. */
up->curregs[R4] &= ~XCLK_MASK;
up->curregs[R4] |= X16CLK;
up->curregs[R12] = brg & 0xff;
up->curregs[R13] = (brg >> 8) & 0xff;
up->curregs[R14] = BRSRC | BRENAB;
/* Character size, stop bits, and parity. */
up->curregs[3] &= ~RxN_MASK;
up->curregs[5] &= ~TxN_MASK;
switch (cflag & CSIZE) {
case CS5:
up->curregs[3] |= Rx5;
up->curregs[5] |= Tx5;
up->parity_mask = 0x1f;
break;
case CS6:
up->curregs[3] |= Rx6;
up->curregs[5] |= Tx6;
up->parity_mask = 0x3f;
break;
case CS7:
up->curregs[3] |= Rx7;
up->curregs[5] |= Tx7;
up->parity_mask = 0x7f;
break;
case CS8:
default:
up->curregs[3] |= Rx8;
up->curregs[5] |= Tx8;
up->parity_mask = 0xff;
break;
};
up->curregs[4] &= ~0x0c;
if (cflag & CSTOPB)
up->curregs[4] |= SB2;
else
up->curregs[4] |= SB1;
if (cflag & PARENB)
up->curregs[4] |= PAR_ENAB;
else
up->curregs[4] &= ~PAR_ENAB;
if (!(cflag & PARODD))
up->curregs[4] |= PAR_EVEN;
else
up->curregs[4] &= ~PAR_EVEN;
up->port.read_status_mask = Rx_OVR;
if (iflag & INPCK)
up->port.read_status_mask |= CRC_ERR | PAR_ERR;
if (iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= BRK_ABRT;
up->port.ignore_status_mask = 0;
if (iflag & IGNPAR)
up->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
if (iflag & IGNBRK) {
up->port.ignore_status_mask |= BRK_ABRT;
if (iflag & IGNPAR)
up->port.ignore_status_mask |= Rx_OVR;
}
if ((cflag & CREAD) == 0)
up->port.ignore_status_mask = 0xff;
}
/* The port lock is not held. */
static void
ip22zilog_set_termios(struct uart_port *port, struct termios *termios,
struct termios *old)
{
struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
unsigned long flags;
int baud, brg;
baud = uart_get_baud_rate(port, termios, old, 1200, 76800);
spin_lock_irqsave(&up->port.lock, flags);
brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
ip22zilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg);
if (UART_ENABLE_MS(&up->port, termios->c_cflag))
up->flags |= IP22ZILOG_FLAG_MODEM_STATUS;
else
up->flags &= ~IP22ZILOG_FLAG_MODEM_STATUS;
up->cflag = termios->c_cflag;
ip22zilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port));
spin_unlock_irqrestore(&up->port.lock, flags);
}
static const char *ip22zilog_type(struct uart_port *port)
{
return "IP22-Zilog";
}
/* We do not request/release mappings of the registers here, this
* happens at early serial probe time.
*/
static void ip22zilog_release_port(struct uart_port *port)
{
}
static int ip22zilog_request_port(struct uart_port *port)
{
return 0;
}
/* These do not need to do anything interesting either. */
static void ip22zilog_config_port(struct uart_port *port, int flags)
{
}
/* We do not support letting the user mess with the divisor, IRQ, etc. */
static int ip22zilog_verify_port(struct uart_port *port, struct serial_struct *ser)
{
return -EINVAL;
}
static struct uart_ops ip22zilog_pops = {
.tx_empty = ip22zilog_tx_empty,
.set_mctrl = ip22zilog_set_mctrl,
.get_mctrl = ip22zilog_get_mctrl,
.stop_tx = ip22zilog_stop_tx,
.start_tx = ip22zilog_start_tx,
.stop_rx = ip22zilog_stop_rx,
.enable_ms = ip22zilog_enable_ms,
.break_ctl = ip22zilog_break_ctl,
.startup = ip22zilog_startup,
.shutdown = ip22zilog_shutdown,
.set_termios = ip22zilog_set_termios,
.type = ip22zilog_type,
.release_port = ip22zilog_release_port,
.request_port = ip22zilog_request_port,
.config_port = ip22zilog_config_port,
.verify_port = ip22zilog_verify_port,
};
static struct uart_ip22zilog_port *ip22zilog_port_table;
static struct zilog_layout **ip22zilog_chip_regs;
static struct uart_ip22zilog_port *ip22zilog_irq_chain;
static int zilog_irq = -1;
static struct uart_driver ip22zilog_reg = {
.owner = THIS_MODULE,
.driver_name = "ttyS",
.devfs_name = "tty/",
.major = TTY_MAJOR,
};
static void * __init alloc_one_table(unsigned long size)
{
void *ret;
ret = kmalloc(size, GFP_KERNEL);
if (ret != NULL)
memset(ret, 0, size);
return ret;
}
static void __init ip22zilog_alloc_tables(void)
{
ip22zilog_port_table = (struct uart_ip22zilog_port *)
alloc_one_table(NUM_CHANNELS * sizeof(struct uart_ip22zilog_port));
ip22zilog_chip_regs = (struct zilog_layout **)
alloc_one_table(NUM_IP22ZILOG * sizeof(struct zilog_layout *));
if (ip22zilog_port_table == NULL || ip22zilog_chip_regs == NULL) {
panic("IP22-Zilog: Cannot allocate IP22-Zilog tables.");
}
}
/* Get the address of the registers for IP22-Zilog instance CHIP. */
static struct zilog_layout * __init get_zs(int chip)
{
unsigned long base;
if (chip < 0 || chip >= NUM_IP22ZILOG) {
panic("IP22-Zilog: Illegal chip number %d in get_zs.", chip);
}
/* Not probe-able, hard code it. */
base = (unsigned long) &sgioc->serport;
zilog_irq = SGI_SERIAL_IRQ;
request_mem_region(base, 8, "IP22-Zilog");
return (struct zilog_layout *) base;
}
#define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */
#ifdef CONFIG_SERIAL_IP22_ZILOG_CONSOLE
static void ip22zilog_put_char(struct zilog_channel *channel, unsigned char ch)
{
int loops = ZS_PUT_CHAR_MAX_DELAY;
/* This is a timed polling loop so do not switch the explicit
* udelay with ZSDELAY as that is a NOP on some platforms. -DaveM
*/
do {
unsigned char val = readb(&channel->control);
if (val & Tx_BUF_EMP) {
ZSDELAY();
break;
}
udelay(5);
} while (--loops);
writeb(ch, &channel->data);
ZSDELAY();
ZS_WSYNC(channel);
}
static void
ip22zilog_console_write(struct console *con, const char *s, unsigned int count)
{
struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index];
struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
unsigned long flags;
int i;
spin_lock_irqsave(&up->port.lock, flags);
for (i = 0; i < count; i++, s++) {
ip22zilog_put_char(channel, *s);
if (*s == 10)
ip22zilog_put_char(channel, 13);
}
udelay(2);
spin_unlock_irqrestore(&up->port.lock, flags);
}
void
ip22serial_console_termios(struct console *con, char *options)
{
int baud = 9600, bits = 8, cflag;
int parity = 'n';
int flow = 'n';
if (!serial_console)
return;
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
cflag = CREAD | HUPCL | CLOCAL;
switch (baud) {
case 150: cflag |= B150; break;
case 300: cflag |= B300; break;
case 600: cflag |= B600; break;
case 1200: cflag |= B1200; break;
case 2400: cflag |= B2400; break;
case 4800: cflag |= B4800; break;
case 9600: cflag |= B9600; break;
case 19200: cflag |= B19200; break;
case 38400: cflag |= B38400; break;
default: baud = 9600; cflag |= B9600; break;
}
con->cflag = cflag | CS8; /* 8N1 */
}
static int __init ip22zilog_console_setup(struct console *con, char *options)
{
struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index];
unsigned long flags;
int baud, brg;
printk("Console: ttyS%d (IP22-Zilog)\n",
(ip22zilog_reg.minor - 64) + con->index);
/* Get firmware console settings. */
ip22serial_console_termios(con, options);
/* Firmware console speed is limited to 150-->38400 baud so
* this hackish cflag thing is OK.
*/
switch (con->cflag & CBAUD) {
case B150: baud = 150; break;
case B300: baud = 300; break;
case B600: baud = 600; break;
case B1200: baud = 1200; break;
case B2400: baud = 2400; break;
case B4800: baud = 4800; break;
default: case B9600: baud = 9600; break;
case B19200: baud = 19200; break;
case B38400: baud = 38400; break;
};
brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
spin_lock_irqsave(&up->port.lock, flags);
up->curregs[R15] = BRKIE;
ip22zilog_convert_to_zs(up, con->cflag, 0, brg);
__ip22zilog_startup(up);
spin_unlock_irqrestore(&up->port.lock, flags);
return 0;
}
static struct console ip22zilog_console = {
.name = "ttyS",
.write = ip22zilog_console_write,
.device = uart_console_device,
.setup = ip22zilog_console_setup,
.flags = CON_PRINTBUFFER,
.index = -1,
.data = &ip22zilog_reg,
};
#define IP22ZILOG_CONSOLE (&ip22zilog_console)
static int __init ip22zilog_console_init(void)
{
int i;
if (con_is_present())
return 0;
for (i = 0; i < NUM_CHANNELS; i++) {
int this_minor = ip22zilog_reg.minor + i;
if ((this_minor - 64) == (serial_console - 1))
break;
}
if (i == NUM_CHANNELS)
return 0;
ip22zilog_console.index = i;
register_console(&ip22zilog_console);
return 0;
}
#else /* CONFIG_SERIAL_IP22_ZILOG_CONSOLE */
#define IP22ZILOG_CONSOLE (NULL)
#define ip22zilog_console_init() do { } while (0)
#endif
static void __init ip22zilog_prepare(void)
{
struct uart_ip22zilog_port *up;
struct zilog_layout *rp;
int channel, chip;
/*
* Temporary fix.
*/
for (channel = 0; channel < NUM_CHANNELS; channel++)
spin_lock_init(&ip22zilog_port_table[channel].port.lock);
ip22zilog_irq_chain = up = &ip22zilog_port_table[0];
for (channel = 0; channel < NUM_CHANNELS - 1; channel++)
up[channel].next = &up[channel + 1];
up[channel].next = NULL;
for (chip = 0; chip < NUM_IP22ZILOG; chip++) {
if (!ip22zilog_chip_regs[chip]) {
ip22zilog_chip_regs[chip] = rp = get_zs(chip);
up[(chip * 2) + 0].port.membase = (char *) &rp->channelA;
up[(chip * 2) + 1].port.membase = (char *) &rp->channelB;
}
/* Channel A */
up[(chip * 2) + 0].port.iotype = UPIO_MEM;
up[(chip * 2) + 0].port.irq = zilog_irq;
up[(chip * 2) + 0].port.uartclk = ZS_CLOCK;
up[(chip * 2) + 0].port.fifosize = 1;
up[(chip * 2) + 0].port.ops = &ip22zilog_pops;
up[(chip * 2) + 0].port.type = PORT_IP22ZILOG;
up[(chip * 2) + 0].port.flags = 0;
up[(chip * 2) + 0].port.line = (chip * 2) + 0;
up[(chip * 2) + 0].flags |= IP22ZILOG_FLAG_IS_CHANNEL_A;
/* Channel B */
up[(chip * 2) + 1].port.iotype = UPIO_MEM;
up[(chip * 2) + 1].port.irq = zilog_irq;
up[(chip * 2) + 1].port.uartclk = ZS_CLOCK;
up[(chip * 2) + 1].port.fifosize = 1;
up[(chip * 2) + 1].port.ops = &ip22zilog_pops;
up[(chip * 2) + 1].port.type = PORT_IP22ZILOG;
up[(chip * 2) + 1].port.flags = 0;
up[(chip * 2) + 1].port.line = (chip * 2) + 1;
up[(chip * 2) + 1].flags |= 0;
}
}
static void __init ip22zilog_init_hw(void)
{
int i;
for (i = 0; i < NUM_CHANNELS; i++) {
struct uart_ip22zilog_port *up = &ip22zilog_port_table[i];
struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
unsigned long flags;
int baud, brg;
spin_lock_irqsave(&up->port.lock, flags);
if (ZS_IS_CHANNEL_A(up)) {
write_zsreg(channel, R9, FHWRES);
ZSDELAY_LONG();
(void) read_zsreg(channel, R0);
}
/* Normal serial TTY. */
up->parity_mask = 0xff;
up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
up->curregs[R3] = RxENAB | Rx8;
up->curregs[R5] = TxENAB | Tx8;
up->curregs[R9] = NV | MIE;
up->curregs[R10] = NRZ;
up->curregs[R11] = TCBR | RCBR;
baud = 9600;
brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
up->curregs[R12] = (brg & 0xff);
up->curregs[R13] = (brg >> 8) & 0xff;
up->curregs[R14] = BRSRC | BRENAB;
__load_zsregs(channel, up->curregs);
spin_unlock_irqrestore(&up->port.lock, flags);
}
}
static int __init ip22zilog_ports_init(void)
{
int ret;
printk(KERN_INFO "Serial: IP22 Zilog driver (%d chips).\n", NUM_IP22ZILOG);
ip22zilog_prepare();
if (request_irq(zilog_irq, ip22zilog_interrupt, 0,
"IP22-Zilog", ip22zilog_irq_chain)) {
panic("IP22-Zilog: Unable to register zs interrupt handler.\n");
}
ip22zilog_init_hw();
/* We can only init this once we have probed the Zilogs
* in the system.
*/
ip22zilog_reg.nr = NUM_CHANNELS;
ip22zilog_reg.cons = IP22ZILOG_CONSOLE;
ip22zilog_reg.minor = ip22serial_current_minor;
ip22serial_current_minor += NUM_CHANNELS;
ret = uart_register_driver(&ip22zilog_reg);
if (ret == 0) {
int i;
for (i = 0; i < NUM_CHANNELS; i++) {
struct uart_ip22zilog_port *up = &ip22zilog_port_table[i];
uart_add_one_port(&ip22zilog_reg, &up->port);
}
}
return ret;
}
static int __init ip22zilog_init(void)
{
/* IP22 Zilog setup is hard coded, no probing to do. */
ip22zilog_alloc_tables();
ip22zilog_ports_init();
ip22zilog_console_init();
return 0;
}
static void __exit ip22zilog_exit(void)
{
int i;
for (i = 0; i < NUM_CHANNELS; i++) {
struct uart_ip22zilog_port *up = &ip22zilog_port_table[i];
uart_remove_one_port(&ip22zilog_reg, &up->port);
}
uart_unregister_driver(&ip22zilog_reg);
}
module_init(ip22zilog_init);
module_exit(ip22zilog_exit);
/* David wrote it but I'm to blame for the bugs ... */
MODULE_AUTHOR("Ralf Baechle <ralf@linux-mips.org>");
MODULE_DESCRIPTION("SGI Zilog serial port driver");
MODULE_LICENSE("GPL");
drivers/serial/ip22zilog.h 0 → 100644
View file @ b7df53b3
#ifndef _IP22_ZILOG_H
#define _IP22_ZILOG_H
#include <asm/byteorder.h>
struct zilog_channel {
#ifdef __BIG_ENDIAN
volatile unsigned char unused0[3];
volatile unsigned char control;
volatile unsigned char unused1[3];
volatile unsigned char data;
#else /* __LITTLE_ENDIAN */
volatile unsigned char control;
volatile unsigned char unused0[3];
volatile unsigned char data;
volatile unsigned char unused1[3];
#endif
};
struct zilog_layout {
struct zilog_channel channelB;
struct zilog_channel channelA;
};
#define NUM_ZSREGS 16
/* Conversion routines to/from brg time constants from/to bits
* per second.
*/
#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
/* The Zilog register set */
#define FLAG 0x7e
/* Write Register 0 */
#define R0 0 /* Register selects */
#define R1 1
#define R2 2
#define R3 3
#define R4 4
#define R5 5
#define R6 6
#define R7 7
#define R8 8
#define R9 9
#define R10 10
#define R11 11
#define R12 12
#define R13 13
#define R14 14
#define R15 15
#define NULLCODE 0 /* Null Code */
#define POINT_HIGH 0x8 /* Select upper half of registers */
#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
#define SEND_ABORT 0x18 /* HDLC Abort */
#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
#define RES_Tx_P 0x28 /* Reset TxINT Pending */
#define ERR_RES 0x30 /* Error Reset */
#define RES_H_IUS 0x38 /* Reset highest IUS */
#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
#define RES_EOM_L 0xC0 /* Reset EOM latch */
/* Write Register 1 */
#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
#define TxINT_ENAB 0x2 /* Tx Int Enable */
#define PAR_SPEC 0x4 /* Parity is special condition */
#define RxINT_DISAB 0 /* Rx Int Disable */
#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
#define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */
#define INT_ERR_Rx 0x18 /* Int on error only */
#define RxINT_MASK 0x18
#define WT_RDY_RT 0x20 /* Wait/Ready on R/T */
#define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */
#define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */
/* Write Register #2 (Interrupt Vector) */
/* Write Register 3 */
#define RxENAB 0x1 /* Rx Enable */
#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
#define ENT_HM 0x10 /* Enter Hunt Mode */
#define AUTO_ENAB 0x20 /* Auto Enables */
#define Rx5 0x0 /* Rx 5 Bits/Character */
#define Rx7 0x40 /* Rx 7 Bits/Character */
#define Rx6 0x80 /* Rx 6 Bits/Character */
#define Rx8 0xc0 /* Rx 8 Bits/Character */
#define RxN_MASK 0xc0
/* Write Register 4 */
#define PAR_ENAB 0x1 /* Parity Enable */
#define PAR_EVEN 0x2 /* Parity Even/Odd* */
#define SYNC_ENAB 0 /* Sync Modes Enable */
#define SB1 0x4 /* 1 stop bit/char */
#define SB15 0x8 /* 1.5 stop bits/char */
#define SB2 0xc /* 2 stop bits/char */
#define MONSYNC 0 /* 8 Bit Sync character */
#define BISYNC 0x10 /* 16 bit sync character */
#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
#define EXTSYNC 0x30 /* External Sync Mode */
#define X1CLK 0x0 /* x1 clock mode */
#define X16CLK 0x40 /* x16 clock mode */
#define X32CLK 0x80 /* x32 clock mode */
#define X64CLK 0xC0 /* x64 clock mode */
#define XCLK_MASK 0xC0
/* Write Register 5 */
#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
#define RTS 0x2 /* RTS */
#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
#define TxENAB 0x8 /* Tx Enable */
#define SND_BRK 0x10 /* Send Break */
#define Tx5 0x0 /* Tx 5 bits (or less)/character */
#define Tx7 0x20 /* Tx 7 bits/character */
#define Tx6 0x40 /* Tx 6 bits/character */
#define Tx8 0x60 /* Tx 8 bits/character */
#define TxN_MASK 0x60
#define DTR 0x80 /* DTR */
/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
/* Write Register 8 (transmit buffer) */
/* Write Register 9 (Master interrupt control) */
#define VIS 1 /* Vector Includes Status */
#define NV 2 /* No Vector */
#define DLC 4 /* Disable Lower Chain */
#define MIE 8 /* Master Interrupt Enable */
#define STATHI 0x10 /* Status high */
#define NORESET 0 /* No reset on write to R9 */
#define CHRB 0x40 /* Reset channel B */
#define CHRA 0x80 /* Reset channel A */
#define FHWRES 0xc0 /* Force hardware reset */
/* Write Register 10 (misc control bits) */
#define BIT6 1 /* 6 bit/8bit sync */
#define LOOPMODE 2 /* SDLC Loop mode */
#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
#define MARKIDLE 8 /* Mark/flag on idle */
#define GAOP 0x10 /* Go active on poll */
#define NRZ 0 /* NRZ mode */
#define NRZI 0x20 /* NRZI mode */
#define FM1 0x40 /* FM1 (transition = 1) */
#define FM0 0x60 /* FM0 (transition = 0) */
#define CRCPS 0x80 /* CRC Preset I/O */
/* Write Register 11 (Clock Mode control) */
#define TRxCXT 0 /* TRxC = Xtal output */
#define TRxCTC 1 /* TRxC = Transmit clock */
#define TRxCBR 2 /* TRxC = BR Generator Output */
#define TRxCDP 3 /* TRxC = DPLL output */
#define TRxCOI 4 /* TRxC O/I */
#define TCRTxCP 0 /* Transmit clock = RTxC pin */
#define TCTRxCP 8 /* Transmit clock = TRxC pin */
#define TCBR 0x10 /* Transmit clock = BR Generator output */
#define TCDPLL 0x18 /* Transmit clock = DPLL output */
#define RCRTxCP 0 /* Receive clock = RTxC pin */
#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
#define RCBR 0x40 /* Receive clock = BR Generator output */
#define RCDPLL 0x60 /* Receive clock = DPLL output */
#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
/* Write Register 12 (lower byte of baud rate generator time constant) */
/* Write Register 13 (upper byte of baud rate generator time constant) */
/* Write Register 14 (Misc control bits) */
#define BRENAB 1 /* Baud rate generator enable */
#define BRSRC 2 /* Baud rate generator source */
#define DTRREQ 4 /* DTR/Request function */
#define AUTOECHO 8 /* Auto Echo */
#define LOOPBAK 0x10 /* Local loopback */
#define SEARCH 0x20 /* Enter search mode */
#define RMC 0x40 /* Reset missing clock */
#define DISDPLL 0x60 /* Disable DPLL */
#define SSBR 0x80 /* Set DPLL source = BR generator */
#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
#define SFMM 0xc0 /* Set FM mode */
#define SNRZI 0xe0 /* Set NRZI mode */
/* Write Register 15 (external/status interrupt control) */
#define ZCIE 2 /* Zero count IE */
#define DCDIE 8 /* DCD IE */
#define SYNCIE 0x10 /* Sync/hunt IE */
#define CTSIE 0x20 /* CTS IE */
#define TxUIE 0x40 /* Tx Underrun/EOM IE */
#define BRKIE 0x80 /* Break/Abort IE */
/* Read Register 0 */
#define Rx_CH_AV 0x1 /* Rx Character Available */
#define ZCOUNT 0x2 /* Zero count */
#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
#define DCD 0x8 /* DCD */
#define SYNC 0x10 /* Sync/hunt */
#define CTS 0x20 /* CTS */
#define TxEOM 0x40 /* Tx underrun */
#define BRK_ABRT 0x80 /* Break/Abort */
/* Read Register 1 */
#define ALL_SNT 0x1 /* All sent */
/* Residue Data for 8 Rx bits/char programmed */
#define RES3 0x8 /* 0/3 */
#define RES4 0x4 /* 0/4 */
#define RES5 0xc /* 0/5 */
#define RES6 0x2 /* 0/6 */
#define RES7 0xa /* 0/7 */
#define RES8 0x6 /* 0/8 */
#define RES18 0xe /* 1/8 */
#define RES28 0x0 /* 2/8 */
/* Special Rx Condition Interrupts */
#define PAR_ERR 0x10 /* Parity error */
#define Rx_OVR 0x20 /* Rx Overrun Error */
#define CRC_ERR 0x40 /* CRC/Framing Error */
#define END_FR 0x80 /* End of Frame (SDLC) */
/* Read Register 2 (channel b only) - Interrupt vector */
#define CHB_Tx_EMPTY 0x00
#define CHB_EXT_STAT 0x02
#define CHB_Rx_AVAIL 0x04
#define CHB_SPECIAL 0x06
#define CHA_Tx_EMPTY 0x08
#define CHA_EXT_STAT 0x0a
#define CHA_Rx_AVAIL 0x0c
#define CHA_SPECIAL 0x0e
#define STATUS_MASK 0x0e
/* Read Register 3 (interrupt pending register) ch a only */
#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
#define CHBTxIP 0x2 /* Channel B Tx IP */
#define CHBRxIP 0x4 /* Channel B Rx IP */
#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
#define CHATxIP 0x10 /* Channel A Tx IP */
#define CHARxIP 0x20 /* Channel A Rx IP */
/* Read Register 8 (receive data register) */
/* Read Register 10 (misc status bits) */
#define ONLOOP 2 /* On loop */
#define LOOPSEND 0x10 /* Loop sending */
#define CLK2MIS 0x40 /* Two clocks missing */
#define CLK1MIS 0x80 /* One clock missing */
/* Read Register 12 (lower byte of baud rate generator constant) */
/* Read Register 13 (upper byte of baud rate generator constant) */
/* Read Register 15 (value of WR 15) */
/* Misc macros */
#define ZS_CLEARERR(channel) do { writeb(ERR_RES, &channel->control); \
udelay(5); } while(0)
#define ZS_CLEARSTAT(channel) do { writeb(RES_EXT_INT, &channel->control); \
udelay(5); } while(0)
#define ZS_CLEARFIFO(channel) do { readb(&channel->data); \
udelay(2); \
readb(&channel->data); \
udelay(2); \
readb(&channel->data); \
udelay(2); } while(0)
#endif /* _IP22_ZILOG_H */
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7