Merge branches 'thermal-core', 'thermal-intel' and 'thermal-soc' into next

Documentation/devicetree/bindings/thermal/exynos-thermal.txt

@@ -11,6 +11,7 @@
 	       "samsung,exynos5420-tmu" for TMU channel 0, 1 on Exynos5420
 	       "samsung,exynos5420-tmu-ext-triminfo" for TMU channels 2, 3 and 4
 			Exynos5420 (Must pass triminfo base and triminfo clock)
+               "samsung,exynos5433-tmu"
 	       "samsung,exynos5440-tmu"
 	       "samsung,exynos7-tmu"
 - interrupt-parent : The phandle for the interrupt controller
@@ -40,9 +41,14 @@
 		for current TMU channel
 	-- "tmu_sclk" clock for functional operation of the current TMU
 		channel
-- vtmu-supply: This entry is optional and provides the regulator node supplying
-		voltage to TMU. If needed this entry can be placed inside
-		board/platform specific dts file.
+
+The Exynos TMU supports generating interrupts when reaching given
+temperature thresholds. Number of supported thermal trip points depends
+on the SoC (only first trip points defined in DT will be configured):
+ - most of SoC: 4
+ - samsung,exynos5433-tmu: 8
+ - samsung,exynos7-tmu: 8
+
 Following properties are mandatory (depending on SoC):
 - samsung,tmu_gain: Gain value for internal TMU operation.
 - samsung,tmu_reference_voltage: Value of TMU IP block's reference voltage
@@ -56,6 +62,12 @@ Following properties are mandatory (depending on SoC):
 - samsung,tmu_default_temp_offset: Default temperature offset
 - samsung,tmu_cal_type: Callibration type
 
+** Optional properties:
+
+- vtmu-supply: This entry is optional and provides the regulator node supplying
+		voltage to TMU. If needed this entry can be placed inside
+		board/platform specific dts file.
+
 Example 1):
 
 	tmu@100C0000 {

Documentation/devicetree/bindings/thermal/mediatek-thermal.txt

+* Mediatek Thermal
+
+This describes the device tree binding for the Mediatek thermal controller
+which measures the on-SoC temperatures. This device does not have its own ADC,
+instead it directly controls the AUXADC via AHB bus accesses. For this reason
+this device needs phandles to the AUXADC. Also it controls a mux in the
+apmixedsys register space via AHB bus accesses, so a phandle to the APMIXEDSYS
+is also needed.
+
+Required properties:
+- compatible: "mediatek,mt8173-thermal"
+- reg: Address range of the thermal controller
+- interrupts: IRQ for the thermal controller
+- clocks, clock-names: Clocks needed for the thermal controller. required
+                       clocks are:
+		       "therm":	 Main clock needed for register access
+		       "auxadc": The AUXADC clock
+- resets: Reference to the reset controller controlling the thermal controller.
+- mediatek,auxadc: A phandle to the AUXADC which the thermal controller uses
+- mediatek,apmixedsys: A phandle to the APMIXEDSYS controller.
+- #thermal-sensor-cells : Should be 0. See ./thermal.txt for a description.
+
+Optional properties:
+- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If
+               unspecified default values shall be used.
+- nvmem-cell-names: Should be "calibration-data"
+
+Example:
+
+	thermal: thermal@1100b000 {
+		#thermal-sensor-cells = <1>;
+		compatible = "mediatek,mt8173-thermal";
+		reg = <0 0x1100b000 0 0x1000>;
+		interrupts = <0 70 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>;
+		clock-names = "therm", "auxadc";
+		resets = <&pericfg MT8173_PERI_THERM_SW_RST>;
+		reset-names = "therm";
+		mediatek,auxadc = <&auxadc>;
+		mediatek,apmixedsys = <&apmixedsys>;
+		nvmem-cells = <&thermal_calibration_data>;
+		nvmem-cell-names = "calibration-data";
+	};

Documentation/thermal/sysfs-api.txt

@@ -72,6 +72,74 @@ temperature) and throttle appropriate devices.
     It deletes the corresponding entry form /sys/class/thermal folder and
     unbind all the thermal cooling devices it uses.
 
+1.1.3 struct thermal_zone_device *thermal_zone_of_sensor_register(
+		struct device *dev, int sensor_id, void *data,
+		const struct thermal_zone_of_device_ops *ops)
+
+	This interface adds a new sensor to a DT thermal zone.
+	This function will search the list of thermal zones described in
+	device tree and look for the zone that refer to the sensor device
+	pointed by dev->of_node as temperature providers. For the zone
+	pointing to the sensor node, the sensor will be added to the DT
+	thermal zone device.
+
+	The parameters for this interface are:
+	dev:		Device node of sensor containing valid node pointer in
+			dev->of_node.
+	sensor_id:	a sensor identifier, in case the sensor IP has more
+			than one sensors
+	data:		a private pointer (owned by the caller) that will be
+			passed back, when a temperature reading is needed.
+	ops:		struct thermal_zone_of_device_ops *.
+
+			get_temp:	a pointer to a function that reads the
+					sensor temperature. This is mandatory
+					callback provided by sensor driver.
+			get_trend: 	a pointer to a function that reads the
+					sensor temperature trend.
+			set_emul_temp:	a pointer to a function that sets
+					sensor emulated temperature.
+	The thermal zone temperature is provided by the get_temp() function
+	pointer of thermal_zone_of_device_ops. When called, it will
+	have the private pointer @data back.
+
+	It returns error pointer if fails otherwise valid thermal zone device
+	handle. Caller should check the return handle with IS_ERR() for finding
+	whether success or not.
+
+1.1.4 void thermal_zone_of_sensor_unregister(struct device *dev,
+		struct thermal_zone_device *tzd)
+
+	This interface unregisters a sensor from a DT thermal zone which was
+	successfully added by interface thermal_zone_of_sensor_register().
+	This function removes the sensor callbacks and private data from the
+	thermal zone device registered with thermal_zone_of_sensor_register()
+	interface. It will also silent the zone by remove the .get_temp() and
+	get_trend() thermal zone device callbacks.
+
+1.1.5 struct thermal_zone_device *devm_thermal_zone_of_sensor_register(
+		struct device *dev, int sensor_id,
+		void *data, const struct thermal_zone_of_device_ops *ops)
+
+	This interface is resource managed version of
+	thermal_zone_of_sensor_register().
+	All details of thermal_zone_of_sensor_register() described in
+	section 1.1.3 is applicable here.
+	The benefit of using this interface to register sensor is that it
+	is not require to explicitly call thermal_zone_of_sensor_unregister()
+	in error path or during driver unbinding as this is done by driver
+	resource manager.
+
+1.1.6 void devm_thermal_zone_of_sensor_unregister(struct device *dev,
+		struct thermal_zone_device *tzd)
+
+	This interface is resource managed version of
+	thermal_zone_of_sensor_unregister().
+	All details of thermal_zone_of_sensor_unregister() described in
+	section 1.1.4 is applicable here.
+	Normally this function will not need to be called and the resource
+	management code will ensure that the resource is freed.
+
 1.2 thermal cooling device interface
 1.2.1 struct thermal_cooling_device *thermal_cooling_device_register(char *name,
 		void *devdata, struct thermal_cooling_device_ops *)

drivers/thermal/Kconfig

@@ -178,6 +178,7 @@ config THERMAL_EMULATION
 config HISI_THERMAL
 	tristate "Hisilicon thermal driver"
 	depends on (ARCH_HISI && CPU_THERMAL && OF) || COMPILE_TEST
+	depends on HAS_IOMEM
 	help
 	  Enable this to plug hisilicon's thermal sensor driver into the Linux
 	  thermal framework. cpufreq is used as the cooling device to throttle
@@ -197,6 +198,7 @@ config IMX_THERMAL
 config SPEAR_THERMAL
 	tristate "SPEAr thermal sensor driver"
 	depends on PLAT_SPEAR || COMPILE_TEST
+	depends on HAS_IOMEM
 	depends on OF
 	help
 	  Enable this to plug the SPEAr thermal sensor driver into the Linux
@@ -206,6 +208,7 @@ config ROCKCHIP_THERMAL
 	tristate "Rockchip thermal driver"
 	depends on ARCH_ROCKCHIP || COMPILE_TEST
 	depends on RESET_CONTROLLER
+	depends on HAS_IOMEM
 	help
 	  Rockchip thermal driver provides support for Temperature sensor
 	  ADC (TS-ADC) found on Rockchip SoCs. It supports one critical
@@ -214,7 +217,7 @@ config ROCKCHIP_THERMAL
 
 config RCAR_THERMAL
 	tristate "Renesas R-Car thermal driver"
-	depends on ARCH_SHMOBILE || COMPILE_TEST
+	depends on ARCH_RENESAS || COMPILE_TEST
 	depends on HAS_IOMEM
 	help
 	  Enable this to plug the R-Car thermal sensor driver into the Linux
@@ -223,6 +226,7 @@ config RCAR_THERMAL
 config KIRKWOOD_THERMAL
 	tristate "Temperature sensor on Marvell Kirkwood SoCs"
 	depends on MACH_KIRKWOOD || COMPILE_TEST
+	depends on HAS_IOMEM
 	depends on OF
 	help
 	  Support for the Kirkwood thermal sensor driver into the Linux thermal
@@ -231,6 +235,7 @@ config KIRKWOOD_THERMAL
 config DOVE_THERMAL
 	tristate "Temperature sensor on Marvell Dove SoCs"
 	depends on ARCH_DOVE || MACH_DOVE || COMPILE_TEST
+	depends on HAS_IOMEM
 	depends on OF
 	help
 	  Support for the Dove thermal sensor driver in the Linux thermal
@@ -249,6 +254,7 @@ config DB8500_THERMAL
 config ARMADA_THERMAL
 	tristate "Armada 370/XP thermal management"
 	depends on ARCH_MVEBU || COMPILE_TEST
+	depends on HAS_IOMEM
 	depends on OF
 	help
 	  Enable this option if you want to have support for thermal management
@@ -266,7 +272,8 @@ config TEGRA_SOCTHERM
 
 config DB8500_CPUFREQ_COOLING
 	tristate "DB8500 cpufreq cooling"
-	depends on ARCH_U8500
+	depends on ARCH_U8500 || COMPILE_TEST
+	depends on HAS_IOMEM
 	depends on CPU_THERMAL
 	default y
 	help
@@ -365,8 +372,18 @@ config INTEL_PCH_THERMAL
 	  Thermal reporting device will provide temperature reading,
 	  programmable trip points and other information.
 
+config MTK_THERMAL
+	tristate "Temperature sensor driver for mediatek SoCs"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	depends on HAS_IOMEM
+	default y
+	help
+	  Enable this option if you want to have support for thermal management
+	  controller present in Mediatek SoCs
+
 menu "Texas Instruments thermal drivers"
 depends on ARCH_HAS_BANDGAP || COMPILE_TEST
+depends on HAS_IOMEM
 source "drivers/thermal/ti-soc-thermal/Kconfig"
 endmenu
 

drivers/thermal/Makefile

@@ -48,3 +48,4 @@ obj-$(CONFIG_INTEL_PCH_THERMAL)	+= intel_pch_thermal.o
 obj-$(CONFIG_ST_THERMAL)	+= st/
 obj-$(CONFIG_TEGRA_SOCTHERM)	+= tegra_soctherm.o
 obj-$(CONFIG_HISI_THERMAL)     += hisi_thermal.o
+obj-$(CONFIG_MTK_THERMAL)	+= mtk_thermal.o

drivers/thermal/intel_pch_thermal.c

@@ -24,6 +24,7 @@
 
 /* Intel PCH thermal Device IDs */
 #define PCH_THERMAL_DID_WPT	0x9CA4 /* Wildcat Point */
+#define PCH_THERMAL_DID_SKL	0x9D31 /* Skylake PCH */
 
 /* Wildcat Point-LP  PCH Thermal registers */
 #define WPT_TEMP	0x0000	/* Temperature */
@@ -201,6 +202,10 @@ static int intel_pch_thermal_probe(struct pci_dev *pdev,
 		ptd->ops = &pch_dev_ops_wpt;
 		dev_name = "pch_wildcat_point";
 		break;
+	case PCH_THERMAL_DID_SKL:
+		ptd->ops = &pch_dev_ops_wpt;
+		dev_name = "pch_skylake";
+		break;
 	default:
 		dev_err(&pdev->dev, "unknown pch thermal device\n");
 		return -ENODEV;
@@ -266,6 +271,7 @@ static void intel_pch_thermal_remove(struct pci_dev *pdev)
 
 static struct pci_device_id intel_pch_thermal_id[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_WPT) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_SKL) },
 	{ 0, },
 };
 MODULE_DEVICE_TABLE(pci, intel_pch_thermal_id);

drivers/thermal/of-thermal.c

@@ -555,6 +555,87 @@ void thermal_zone_of_sensor_unregister(struct device *dev,
 }
 EXPORT_SYMBOL_GPL(thermal_zone_of_sensor_unregister);
 
+static void devm_thermal_zone_of_sensor_release(struct device *dev, void *res)
+{
+	thermal_zone_of_sensor_unregister(dev,
+					  *(struct thermal_zone_device **)res);
+}
+
+static int devm_thermal_zone_of_sensor_match(struct device *dev, void *res,
+					     void *data)
+{
+	struct thermal_zone_device **r = res;
+
+	if (WARN_ON(!r || !*r))
+		return 0;
+
+	return *r == data;
+}
+
+/**
+ * devm_thermal_zone_of_sensor_register - Resource managed version of
+ *				thermal_zone_of_sensor_register()
+ * @dev: a valid struct device pointer of a sensor device. Must contain
+ *       a valid .of_node, for the sensor node.
+ * @sensor_id: a sensor identifier, in case the sensor IP has more
+ *	       than one sensors
+ * @data: a private pointer (owned by the caller) that will be passed
+ *	  back, when a temperature reading is needed.
+ * @ops: struct thermal_zone_of_device_ops *. Must contain at least .get_temp.
+ *
+ * Refer thermal_zone_of_sensor_register() for more details.
+ *
+ * Return: On success returns a valid struct thermal_zone_device,
+ * otherwise, it returns a corresponding ERR_PTR(). Caller must
+ * check the return value with help of IS_ERR() helper.
+ * Registered hermal_zone_device device will automatically be
+ * released when device is unbounded.
+ */
+struct thermal_zone_device *devm_thermal_zone_of_sensor_register(
+	struct device *dev, int sensor_id,
+	void *data, const struct thermal_zone_of_device_ops *ops)
+{
+	struct thermal_zone_device **ptr, *tzd;
+
+	ptr = devres_alloc(devm_thermal_zone_of_sensor_release, sizeof(*ptr),
+			   GFP_KERNEL);
+	if (!ptr)
+		return ERR_PTR(-ENOMEM);
+
+	tzd = thermal_zone_of_sensor_register(dev, sensor_id, data, ops);
+	if (IS_ERR(tzd)) {
+		devres_free(ptr);
+		return tzd;
+	}
+
+	*ptr = tzd;
+	devres_add(dev, ptr);
+
+	return tzd;
+}
+EXPORT_SYMBOL_GPL(devm_thermal_zone_of_sensor_register);
+
+/**
+ * devm_thermal_zone_of_sensor_unregister - Resource managed version of
+ *				thermal_zone_of_sensor_unregister().
+ * @dev: Device for which which resource was allocated.
+ * @tzd: a pointer to struct thermal_zone_device where the sensor is registered.
+ *
+ * This function removes the sensor callbacks and private data from the
+ * thermal zone device registered with devm_thermal_zone_of_sensor_register()
+ * API. It will also silent the zone by remove the .get_temp() and .get_trend()
+ * thermal zone device callbacks.
+ * Normally this function will not need to be called and the resource
+ * management code will ensure that the resource is freed.
+ */
+void devm_thermal_zone_of_sensor_unregister(struct device *dev,
+					    struct thermal_zone_device *tzd)
+{
+	WARN_ON(devres_release(dev, devm_thermal_zone_of_sensor_release,
+			       devm_thermal_zone_of_sensor_match, tzd));
+}
+EXPORT_SYMBOL_GPL(devm_thermal_zone_of_sensor_unregister);
+
 /***   functions parsing device tree nodes   ***/
 
 /**

drivers/thermal/rcar_thermal.c

@@ -430,8 +430,7 @@ static int rcar_thermal_probe(struct platform_device *pdev)
 	struct rcar_thermal_priv *priv;
 	struct device *dev = &pdev->dev;
 	struct resource *res, *irq;
-	const struct of_device_id *of_id = of_match_device(rcar_thermal_dt_ids, dev);
-	unsigned long of_data = (unsigned long)of_id->data;
+	unsigned long of_data = (unsigned long)of_device_get_match_data(dev);
 	int mres = 0;
 	int i;
 	int ret = -ENODEV;

drivers/thermal/rockchip_thermal.c

@@ -58,8 +58,8 @@ enum sensor_id {
 
 /**
  * The conversion table has the adc value and temperature.
- * ADC_DECREMENT: the adc value is of diminishing.(e.g. v2_code_table)
- * ADC_INCREMENT: the adc value is incremental.(e.g. v3_code_table)
+ * ADC_DECREMENT: the adc value is of diminishing.(e.g. rk3288_code_table)
+ * ADC_INCREMENT: the adc value is incremental.(e.g. rk3368_code_table)
  */
 enum adc_sort_mode {
 	ADC_DECREMENT = 0,
@@ -135,7 +135,13 @@ struct rockchip_thermal_data {
 	enum tshut_polarity tshut_polarity;
 };
 
-/* TSADC Sensor info define: */
+/**
+ * TSADC Sensor Register description:
+ *
+ * TSADCV2_* are used for RK3288 SoCs, the other chips can reuse it.
+ * TSADCV3_* are used for newer SoCs than RK3288. (e.g: RK3228, RK3399)
+ *
+ */
 #define TSADCV2_AUTO_CON			0x04
 #define TSADCV2_INT_EN				0x08
 #define TSADCV2_INT_PD				0x0c
@@ -149,13 +155,20 @@ struct rockchip_thermal_data {
 #define TSADCV2_AUTO_EN				BIT(0)
 #define TSADCV2_AUTO_SRC_EN(chn)		BIT(4 + (chn))
 #define TSADCV2_AUTO_TSHUT_POLARITY_HIGH	BIT(8)
+/**
+ * TSADCV1_AUTO_Q_SEL_EN:
+ * whether select (1024 - tsadc_q) as output
+ * 1'b0:use tsadc_q as output(temperature-code is rising sequence)
+ * 1'b1:use(1024 - tsadc_q) as output (temperature-code is falling sequence)
+ */
+#define TSADCV3_AUTO_Q_SEL_EN			BIT(1)
 
 #define TSADCV2_INT_SRC_EN(chn)			BIT(chn)
 #define TSADCV2_SHUT_2GPIO_SRC_EN(chn)		BIT(4 + (chn))
 #define TSADCV2_SHUT_2CRU_SRC_EN(chn)		BIT(8 + (chn))
 
-#define TSADCV1_INT_PD_CLEAR_MASK		~BIT(16)
 #define TSADCV2_INT_PD_CLEAR_MASK		~BIT(8)
+#define TSADCV3_INT_PD_CLEAR_MASK		~BIT(16)
 
 #define TSADCV2_DATA_MASK			0xfff
 #define TSADCV3_DATA_MASK			0x3ff
@@ -177,45 +190,46 @@ struct tsadc_table {
  * linearly interpolated.
  * Code to Temperature mapping should be updated based on sillcon results.
  */
-static const struct tsadc_table v1_code_table[] = {
-	{TSADCV3_DATA_MASK, -40000},
-	{436, -40000},
-	{431, -35000},
-	{426, -30000},
-	{421, -25000},
-	{416, -20000},
-	{411, -15000},
-	{406, -10000},
-	{401, -5000},
-	{395, 0},
-	{390, 5000},
-	{385, 10000},
-	{380, 15000},
-	{375, 20000},
-	{370, 25000},
-	{364, 30000},
-	{359, 35000},
-	{354, 40000},
-	{349, 45000},
-	{343, 50000},
-	{338, 55000},
-	{333, 60000},
-	{328, 65000},
-	{322, 70000},
-	{317, 75000},
-	{312, 80000},
-	{307, 85000},
-	{301, 90000},
-	{296, 95000},
-	{291, 100000},
-	{286, 105000},
-	{280, 110000},
-	{275, 115000},
-	{270, 120000},
-	{264, 125000},
+static const struct tsadc_table rk3228_code_table[] = {
+	{0, -40000},
+	{588, -40000},
+	{593, -35000},
+	{598, -30000},
+	{603, -25000},
+	{608, -20000},
+	{613, -15000},
+	{618, -10000},
+	{623, -5000},
+	{629, 0},
+	{634, 5000},
+	{639, 10000},
+	{644, 15000},
+	{649, 20000},
+	{654, 25000},
+	{660, 30000},
+	{665, 35000},
+	{670, 40000},
+	{675, 45000},
+	{681, 50000},
+	{686, 55000},
+	{691, 60000},
+	{696, 65000},
+	{702, 70000},
+	{707, 75000},
+	{712, 80000},
+	{717, 85000},
+	{723, 90000},
+	{728, 95000},
+	{733, 100000},
+	{738, 105000},
+	{744, 110000},
+	{749, 115000},
+	{754, 120000},
+	{760, 125000},
+	{TSADCV2_DATA_MASK, 125000},
 };
 
-static const struct tsadc_table v2_code_table[] = {
+static const struct tsadc_table rk3288_code_table[] = {
 	{TSADCV2_DATA_MASK, -40000},
 	{3800, -40000},
 	{3792, -35000},
@@ -253,7 +267,7 @@ static const struct tsadc_table v2_code_table[] = {
 	{3421, 125000},
 };
 
-static const struct tsadc_table v3_code_table[] = {
+static const struct tsadc_table rk3368_code_table[] = {
 	{0, -40000},
 	{106, -40000},
 	{108, -35000},
@@ -292,42 +306,43 @@ static const struct tsadc_table v3_code_table[] = {
 	{TSADCV3_DATA_MASK, 125000},
 };
 
-static const struct tsadc_table v4_code_table[] = {
-	{TSADCV3_DATA_MASK, -40000},
-	{431, -40000},
-	{426, -35000},
-	{421, -30000},
-	{415, -25000},
-	{410, -20000},
-	{405, -15000},
-	{399, -10000},
-	{394, -5000},
-	{389, 0},
-	{383, 5000},
-	{378, 10000},
-	{373, 15000},
-	{367, 20000},
-	{362, 25000},
-	{357, 30000},
-	{351, 35000},
-	{346, 40000},
-	{340, 45000},
-	{335, 50000},
-	{330, 55000},
-	{324, 60000},
-	{319, 65000},
-	{313, 70000},
-	{308, 75000},
-	{302, 80000},
-	{297, 85000},
-	{291, 90000},
-	{286, 95000},
-	{281, 100000},
-	{275, 105000},
-	{270, 110000},
-	{264, 115000},
-	{259, 120000},
-	{253, 125000},
+static const struct tsadc_table rk3399_code_table[] = {
+	{0, -40000},
+	{593, -40000},
+	{598, -35000},
+	{603, -30000},
+	{609, -25000},
+	{614, -20000},
+	{619, -15000},
+	{625, -10000},
+	{630, -5000},
+	{635, 0},
+	{641, 5000},
+	{646, 10000},
+	{651, 15000},
+	{657, 20000},
+	{662, 25000},
+	{667, 30000},
+	{673, 35000},
+	{678, 40000},
+	{684, 45000},
+	{689, 50000},
+	{694, 55000},
+	{700, 60000},
+	{705, 65000},
+	{711, 70000},
+	{716, 75000},
+	{722, 80000},
+	{727, 85000},
+	{733, 90000},
+	{738, 95000},
+	{743, 100000},
+	{749, 105000},
+	{754, 110000},
+	{760, 115000},
+	{765, 120000},
+	{771, 125000},
+	{TSADCV3_DATA_MASK, 125000},
 };
 
 static u32 rk_tsadcv2_temp_to_code(struct chip_tsadc_table table,
@@ -411,7 +426,7 @@ static int rk_tsadcv2_code_to_temp(struct chip_tsadc_table table, u32 code,
 	 * temperature between 2 table entries is linear and interpolate
 	 * to produce less granular result.
 	 */
-	num = table.id[mid].temp - v2_code_table[mid - 1].temp;
+	num = table.id[mid].temp - table.id[mid - 1].temp;
 	num *= abs(table.id[mid - 1].code - code);
 	denom = abs(table.id[mid - 1].code - table.id[mid].code);
 	*temp = table.id[mid - 1].temp + (num / denom);
@@ -453,20 +468,20 @@ static void rk_tsadcv2_initialize(void __iomem *regs,
 		       regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE);
 }
 
-static void rk_tsadcv1_irq_ack(void __iomem *regs)
+static void rk_tsadcv2_irq_ack(void __iomem *regs)
 {
 	u32 val;
 
 	val = readl_relaxed(regs + TSADCV2_INT_PD);
-	writel_relaxed(val & TSADCV1_INT_PD_CLEAR_MASK, regs + TSADCV2_INT_PD);
+	writel_relaxed(val & TSADCV2_INT_PD_CLEAR_MASK, regs + TSADCV2_INT_PD);
 }
 
-static void rk_tsadcv2_irq_ack(void __iomem *regs)
+static void rk_tsadcv3_irq_ack(void __iomem *regs)
 {
 	u32 val;
 
 	val = readl_relaxed(regs + TSADCV2_INT_PD);
-	writel_relaxed(val & TSADCV2_INT_PD_CLEAR_MASK, regs + TSADCV2_INT_PD);
+	writel_relaxed(val & TSADCV3_INT_PD_CLEAR_MASK, regs + TSADCV2_INT_PD);
 }
 
 static void rk_tsadcv2_control(void __iomem *regs, bool enable)
@@ -482,6 +497,25 @@ static void rk_tsadcv2_control(void __iomem *regs, bool enable)
 	writel_relaxed(val, regs + TSADCV2_AUTO_CON);
 }
 
+/**
+ * @rk_tsadcv3_control:
+ * TSADC controller works at auto mode, and some SoCs need set the tsadc_q_sel
+ * bit on TSADCV2_AUTO_CON[1]. The (1024 - tsadc_q) as output adc value if
+ * setting this bit to enable.
+ */
+static void rk_tsadcv3_control(void __iomem *regs, bool enable)
+{
+	u32 val;
+
+	val = readl_relaxed(regs + TSADCV2_AUTO_CON);
+	if (enable)
+		val |= TSADCV2_AUTO_EN | TSADCV3_AUTO_Q_SEL_EN;
+	else
+		val &= ~TSADCV2_AUTO_EN;
+
+	writel_relaxed(val, regs + TSADCV2_AUTO_CON);
+}
+
 static int rk_tsadcv2_get_temp(struct chip_tsadc_table table,
 			       int chn, void __iomem *regs, int *temp)
 {
@@ -531,17 +565,17 @@ static const struct rockchip_tsadc_chip rk3228_tsadc_data = {
 	.tshut_temp = 95000,
 
 	.initialize = rk_tsadcv2_initialize,
-	.irq_ack = rk_tsadcv1_irq_ack,
-	.control = rk_tsadcv2_control,
+	.irq_ack = rk_tsadcv3_irq_ack,
+	.control = rk_tsadcv3_control,
 	.get_temp = rk_tsadcv2_get_temp,
 	.set_tshut_temp = rk_tsadcv2_tshut_temp,
 	.set_tshut_mode = rk_tsadcv2_tshut_mode,
 
 	.table = {
-		.id = v1_code_table,
-		.length = ARRAY_SIZE(v1_code_table),
+		.id = rk3228_code_table,
+		.length = ARRAY_SIZE(rk3228_code_table),
 		.data_mask = TSADCV3_DATA_MASK,
-		.mode = ADC_DECREMENT,
+		.mode = ADC_INCREMENT,
 	},
 };
 
@@ -562,8 +596,8 @@ static const struct rockchip_tsadc_chip rk3288_tsadc_data = {
 	.set_tshut_mode = rk_tsadcv2_tshut_mode,
 
 	.table = {
-		.id = v2_code_table,
-		.length = ARRAY_SIZE(v2_code_table),
+		.id = rk3288_code_table,
+		.length = ARRAY_SIZE(rk3288_code_table),
 		.data_mask = TSADCV2_DATA_MASK,
 		.mode = ADC_DECREMENT,
 	},
@@ -586,8 +620,8 @@ static const struct rockchip_tsadc_chip rk3368_tsadc_data = {
 	.set_tshut_mode = rk_tsadcv2_tshut_mode,
 
 	.table = {
-		.id = v3_code_table,
-		.length = ARRAY_SIZE(v3_code_table),
+		.id = rk3368_code_table,
+		.length = ARRAY_SIZE(rk3368_code_table),
 		.data_mask = TSADCV3_DATA_MASK,
 		.mode = ADC_INCREMENT,
 	},
@@ -603,17 +637,17 @@ static const struct rockchip_tsadc_chip rk3399_tsadc_data = {
 	.tshut_temp = 95000,
 
 	.initialize = rk_tsadcv2_initialize,
-	.irq_ack = rk_tsadcv1_irq_ack,
-	.control = rk_tsadcv2_control,
+	.irq_ack = rk_tsadcv3_irq_ack,
+	.control = rk_tsadcv3_control,
 	.get_temp = rk_tsadcv2_get_temp,
 	.set_tshut_temp = rk_tsadcv2_tshut_temp,
 	.set_tshut_mode = rk_tsadcv2_tshut_mode,
 
 	.table = {
-		.id = v4_code_table,
-		.length = ARRAY_SIZE(v4_code_table),
+		.id = rk3399_code_table,
+		.length = ARRAY_SIZE(rk3399_code_table),
 		.data_mask = TSADCV3_DATA_MASK,
-		.mode = ADC_DECREMENT,
+		.mode = ADC_INCREMENT,
 	},
 };
 
@@ -693,14 +727,13 @@ static int rockchip_configure_from_dt(struct device *dev,
 			 thermal->chip->tshut_temp);
 		thermal->tshut_temp = thermal->chip->tshut_temp;
 	} else {
-		thermal->tshut_temp = shut_temp;
-	}
-
-	if (thermal->tshut_temp > INT_MAX) {
+		if (shut_temp > INT_MAX) {
 			dev_err(dev, "Invalid tshut temperature specified: %d\n",
-			thermal->tshut_temp);
+				shut_temp);
 			return -ERANGE;
 		}
+		thermal->tshut_temp = shut_temp;
+	}
 
 	if (of_property_read_u32(np, "rockchip,hw-tshut-mode", &tshut_mode)) {
 		dev_warn(dev,

drivers/thermal/samsung/Kconfig

 config EXYNOS_THERMAL
 	tristate "Exynos thermal management unit driver"
 	depends on THERMAL_OF
+	depends on HAS_IOMEM
 	help
 	  If you say yes here you get support for the TMU (Thermal Management
 	  Unit) driver for SAMSUNG EXYNOS series of SoCs. This driver initialises

drivers/thermal/samsung/exynos_tmu.c

@@ -184,6 +184,7 @@
  * @temp_error2: fused value of the second point trim.
  * @regulator: pointer to the TMU regulator structure.
  * @reg_conf: pointer to structure to register with core thermal.
+ * @ntrip: number of supported trip points.
  * @tmu_initialize: SoC specific TMU initialization method
  * @tmu_control: SoC specific TMU control method
  * @tmu_read: SoC specific TMU temperature read method
@@ -203,6 +204,7 @@ struct exynos_tmu_data {
 	u16 temp_error1, temp_error2;
 	struct regulator *regulator;
 	struct thermal_zone_device *tzd;
+	unsigned int ntrip;
 
 	int (*tmu_initialize)(struct platform_device *pdev);
 	void (*tmu_control)(struct platform_device *pdev, bool on);
@@ -346,6 +348,14 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
 	struct exynos_tmu_data *data = platform_get_drvdata(pdev);
 	int ret;
 
+	if (of_thermal_get_ntrips(data->tzd) > data->ntrip) {
+		dev_info(&pdev->dev,
+			 "More trip points than supported by this TMU.\n");
+		dev_info(&pdev->dev,
+			 "%d trip points should be configured in polling mode.\n",
+			 (of_thermal_get_ntrips(data->tzd) - data->ntrip));
+	}
+
 	mutex_lock(&data->lock);
 	clk_enable(data->clk);
 	if (!IS_ERR(data->clk_sec))
@@ -1210,6 +1220,7 @@ static int exynos_map_dt_data(struct platform_device *pdev)
 		data->tmu_control = exynos4210_tmu_control;
 		data->tmu_read = exynos4210_tmu_read;
 		data->tmu_clear_irqs = exynos4210_tmu_clear_irqs;
+		data->ntrip = 4;
 		break;
 	case SOC_ARCH_EXYNOS3250:
 	case SOC_ARCH_EXYNOS4412:
@@ -1222,6 +1233,7 @@ static int exynos_map_dt_data(struct platform_device *pdev)
 		data->tmu_read = exynos4412_tmu_read;
 		data->tmu_set_emulation = exynos4412_tmu_set_emulation;
 		data->tmu_clear_irqs = exynos4210_tmu_clear_irqs;
+		data->ntrip = 4;
 		break;
 	case SOC_ARCH_EXYNOS5433:
 		data->tmu_initialize = exynos5433_tmu_initialize;
@@ -1229,6 +1241,7 @@ static int exynos_map_dt_data(struct platform_device *pdev)
 		data->tmu_read = exynos4412_tmu_read;
 		data->tmu_set_emulation = exynos4412_tmu_set_emulation;
 		data->tmu_clear_irqs = exynos4210_tmu_clear_irqs;
+		data->ntrip = 8;
 		break;
 	case SOC_ARCH_EXYNOS5440:
 		data->tmu_initialize = exynos5440_tmu_initialize;
@@ -1236,6 +1249,7 @@ static int exynos_map_dt_data(struct platform_device *pdev)
 		data->tmu_read = exynos5440_tmu_read;
 		data->tmu_set_emulation = exynos5440_tmu_set_emulation;
 		data->tmu_clear_irqs = exynos5440_tmu_clear_irqs;
+		data->ntrip = 4;
 		break;
 	case SOC_ARCH_EXYNOS7:
 		data->tmu_initialize = exynos7_tmu_initialize;
@@ -1243,6 +1257,7 @@ static int exynos_map_dt_data(struct platform_device *pdev)
 		data->tmu_read = exynos7_tmu_read;
 		data->tmu_set_emulation = exynos4412_tmu_set_emulation;
 		data->tmu_clear_irqs = exynos4210_tmu_clear_irqs;
+		data->ntrip = 8;
 		break;
 	default:
 		dev_err(&pdev->dev, "Platform not supported\n");
@@ -1295,7 +1310,7 @@ static int exynos_tmu_probe(struct platform_device *pdev)
 	 * TODO: Add regulator as an SOC feature, so that regulator enable
 	 * is a compulsory call.
 	 */
-	data->regulator = devm_regulator_get(&pdev->dev, "vtmu");
+	data->regulator = devm_regulator_get_optional(&pdev->dev, "vtmu");
 	if (!IS_ERR(data->regulator)) {
 		ret = regulator_enable(data->regulator);
 		if (ret) {
@@ -1303,6 +1318,8 @@ static int exynos_tmu_probe(struct platform_device *pdev)
 			return ret;
 		}
 	} else {
+		if (PTR_ERR(data->regulator) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
 		dev_info(&pdev->dev, "Regulator node (vtmu) not found\n");
 	}
 

drivers/thermal/tegra_soctherm.c

@@ -57,7 +57,7 @@
 #define READBACK_VALUE_MASK			0xff00
 #define READBACK_VALUE_SHIFT			8
 #define READBACK_ADD_HALF			BIT(7)
-#define READBACK_NEGATE				BIT(1)
+#define READBACK_NEGATE				BIT(0)
 
 #define FUSE_TSENSOR8_CALIB			0x180
 #define FUSE_SPARE_REALIGNMENT_REG_0		0x1fc

drivers/thermal/ti-soc-thermal/ti-bandgap.c

@@ -1265,7 +1265,7 @@ static
 int ti_bandgap_probe(struct platform_device *pdev)
 {
 	struct ti_bandgap *bgp;
-	int clk_rate, ret = 0, i;
+	int clk_rate, ret, i;
 
 	bgp = ti_bandgap_build(pdev);
 	if (IS_ERR(bgp)) {
@@ -1288,16 +1288,14 @@ int ti_bandgap_probe(struct platform_device *pdev)
 	}
 
 	bgp->fclock = clk_get(NULL, bgp->conf->fclock_name);
-	ret = IS_ERR(bgp->fclock);
-	if (ret) {
+	if (IS_ERR(bgp->fclock)) {
 		dev_err(&pdev->dev, "failed to request fclock reference\n");
 		ret = PTR_ERR(bgp->fclock);
 		goto free_irqs;
 	}
 
 	bgp->div_clk = clk_get(NULL, bgp->conf->div_ck_name);
-	ret = IS_ERR(bgp->div_clk);
-	if (ret) {
+	if (IS_ERR(bgp->div_clk)) {
 		dev_err(&pdev->dev, "failed to request div_ts_ck clock ref\n");
 		ret = PTR_ERR(bgp->div_clk);
 		goto free_irqs;
@@ -1314,7 +1312,7 @@ int ti_bandgap_probe(struct platform_device *pdev)
 		 * may not be accurate
 		 */
 		val = ti_bandgap_readl(bgp, tsr->bgap_efuse);
-		if (ret || !val)
+		if (!val)
 			dev_info(&pdev->dev,
 				 "Non-trimmed BGAP, Temp not accurate\n");
 	}

include/linux/thermal.h

@@ -362,6 +362,11 @@ thermal_zone_of_sensor_register(struct device *dev, int id, void *data,
 				const struct thermal_zone_of_device_ops *ops);
 void thermal_zone_of_sensor_unregister(struct device *dev,
 				       struct thermal_zone_device *tz);
+struct thermal_zone_device *devm_thermal_zone_of_sensor_register(
+		struct device *dev, int id, void *data,
+		const struct thermal_zone_of_device_ops *ops);
+void devm_thermal_zone_of_sensor_unregister(struct device *dev,
+					    struct thermal_zone_device *tz);
 #else
 static inline struct thermal_zone_device *
 thermal_zone_of_sensor_register(struct device *dev, int id, void *data,
@@ -376,6 +381,19 @@ void thermal_zone_of_sensor_unregister(struct device *dev,
 {
 }
 
+static inline struct thermal_zone_device *devm_thermal_zone_of_sensor_register(
+		struct device *dev, int id, void *data,
+		const struct thermal_zone_of_device_ops *ops)
+{
+	return ERR_PTR(-ENODEV);
+}
+
+static inline
+void devm_thermal_zone_of_sensor_unregister(struct device *dev,
+					    struct thermal_zone_device *tz)
+{
+}
+
 #endif
 
 #if IS_ENABLED(CONFIG_THERMAL)