Commit ba714a9c authored by Thomas Gleixner's avatar Thomas Gleixner Committed by Linus Walleij

pinctrl/amd: Use regular interrupt instead of chained

The AMD pinctrl driver uses a chained interrupt to demultiplex the GPIO
interrupts. Kevin Vandeventer reported, that his new AMD Ryzen locks up
hard on boot when the AMD pinctrl driver is initialized. The reason is an
interrupt storm. It's not clear whether that's caused by hardware or
firmware or both.

Using chained interrupts on X86 is a dangerous endavour. If a system is
misconfigured or the hardware buggy there is no safety net to catch an
interrupt storm.

Convert the driver to use a regular interrupt for the demultiplex
handler. This allows the interrupt storm detector to catch the malfunction
and lets the system boot up.

This should be backported to stable because it's likely that more users run
into this problem as the AMD Ryzen machines are spreading.

Reported-by: Kevin Vandeventer
Link: https://bugzilla.suse.com/show_bug.cgi?id=1034261Signed-off-by: default avatarThomas Gleixner <tglx@linutronix.de>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent 3c2993b8
......@@ -495,64 +495,54 @@ static struct irq_chip amd_gpio_irqchip = {
.flags = IRQCHIP_SKIP_SET_WAKE,
};
static void amd_gpio_irq_handler(struct irq_desc *desc)
#define PIN_IRQ_PENDING (BIT(INTERRUPT_STS_OFF) | BIT(WAKE_STS_OFF))
static irqreturn_t amd_gpio_irq_handler(int irq, void *dev_id)
{
u32 i;
u32 off;
u32 reg;
u32 pin_reg;
u64 reg64;
int handled = 0;
unsigned int irq;
struct amd_gpio *gpio_dev = dev_id;
struct gpio_chip *gc = &gpio_dev->gc;
irqreturn_t ret = IRQ_NONE;
unsigned int i, irqnr;
unsigned long flags;
struct irq_chip *chip = irq_desc_get_chip(desc);
struct gpio_chip *gc = irq_desc_get_handler_data(desc);
struct amd_gpio *gpio_dev = gpiochip_get_data(gc);
u32 *regs, regval;
u64 status, mask;
chained_irq_enter(chip, desc);
/*enable GPIO interrupt again*/
/* Read the wake status */
raw_spin_lock_irqsave(&gpio_dev->lock, flags);
reg = readl(gpio_dev->base + WAKE_INT_STATUS_REG1);
reg64 = reg;
reg64 = reg64 << 32;
reg = readl(gpio_dev->base + WAKE_INT_STATUS_REG0);
reg64 |= reg;
status = readl(gpio_dev->base + WAKE_INT_STATUS_REG1);
status <<= 32;
status |= readl(gpio_dev->base + WAKE_INT_STATUS_REG0);
raw_spin_unlock_irqrestore(&gpio_dev->lock, flags);
/*
* first 46 bits indicates interrupt status.
* one bit represents four interrupt sources.
*/
for (off = 0; off < 46 ; off++) {
if (reg64 & BIT(off)) {
/* Bit 0-45 contain the relevant status bits */
status &= (1ULL << 46) - 1;
regs = gpio_dev->base;
for (mask = 1, irqnr = 0; status; mask <<= 1, regs += 4, irqnr += 4) {
if (!(status & mask))
continue;
status &= ~mask;
/* Each status bit covers four pins */
for (i = 0; i < 4; i++) {
pin_reg = readl(gpio_dev->base +
(off * 4 + i) * 4);
if ((pin_reg & BIT(INTERRUPT_STS_OFF)) ||
(pin_reg & BIT(WAKE_STS_OFF))) {
irq = irq_find_mapping(gc->irqdomain,
off * 4 + i);
regval = readl(regs + i);
if (!(regval & PIN_IRQ_PENDING))
continue;
irq = irq_find_mapping(gc->irqdomain, irqnr + i);
generic_handle_irq(irq);
writel(pin_reg,
gpio_dev->base
+ (off * 4 + i) * 4);
handled++;
}
/* Clear interrupt */
writel(regval, regs + i);
ret = IRQ_HANDLED;
}
}
}
if (handled == 0)
handle_bad_irq(desc);
/* Signal EOI to the GPIO unit */
raw_spin_lock_irqsave(&gpio_dev->lock, flags);
reg = readl(gpio_dev->base + WAKE_INT_MASTER_REG);
reg |= EOI_MASK;
writel(reg, gpio_dev->base + WAKE_INT_MASTER_REG);
regval = readl(gpio_dev->base + WAKE_INT_MASTER_REG);
regval |= EOI_MASK;
writel(regval, gpio_dev->base + WAKE_INT_MASTER_REG);
raw_spin_unlock_irqrestore(&gpio_dev->lock, flags);
chained_irq_exit(chip, desc);
return ret;
}
static int amd_get_groups_count(struct pinctrl_dev *pctldev)
......@@ -821,10 +811,11 @@ static int amd_gpio_probe(struct platform_device *pdev)
goto out2;
}
gpiochip_set_chained_irqchip(&gpio_dev->gc,
&amd_gpio_irqchip,
irq_base,
amd_gpio_irq_handler);
ret = devm_request_irq(&pdev->dev, irq_base, amd_gpio_irq_handler, 0,
KBUILD_MODNAME, gpio_dev);
if (ret)
goto out2;
platform_set_drvdata(pdev, gpio_dev);
dev_dbg(&pdev->dev, "amd gpio driver loaded\n");
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment